Owner's Manual
Table Of Contents
- Safety Instructions
- Table of Contents
- 1. Introduction
- 2. Preparations
- 3. Recording
- Recording Video and Photos
- Adjusting Camera and Recording Settings
- Video Recording Configuration: Video Format, System Frequency, Resolution and Frame Rate
- Proxy Clips
- Sub Recording Clips
- Shutter Speed
- ISO Speed/Gain
- ND Filter
- Aperture
- White Balance
- Zoom
- Focus
- Image Stabilization
- Onscreen Markers, Zebra Patterns and False Color
- Setting the Time Code
- Synchronizing with an External Device
- Recording Audio
- Audio Format for MP4 Clips
- Recording Audio Using the Second Card Recording Functions
- Connecting an External Microphone or External Audio Input Source to the Camera
- Selecting the Audio Input Source for Audio Channels
- Adjusting the Audio Recording Level
- Advanced Audio Input Settings
- Monitoring the Audio with Headphones
- Colors Bars/Audio Reference Signal
- Video Scopes
- Adding Marks to Clips in CAMERA Mode
- Using Metadata
- Special Recording Modes
- Infrared Recording
- Using the RC-V100 Remote Controller
- Recording Remotely Using an NU Protocol Compatible Device
- Web Camera Function
- 4. Customization
- 5. Playback
- 6. External Connections
- 7. Network Functions
- 8. Additional Information
99
Video Scopes
Video Scopes
The camera can display a simplified waveform monitor or a vectorscope to check your recordings. The selected
video scope is displayed on the screen and can be output to other monitoring devices as well.
Displaying a Video Scope
1 Select > [
A
Assistance Functions] >
[WFM Function] > [Waveform Monitor] or
[Vectorscope].
2Press the WFM button.
• You can also use direct touch control (A 49) to turn
the [Waveform Monitor]/[Vectorscope] setting on/off.
• Alternatively, you can use one of the >
[
A
Assistance Functions] > [WFM:] settings to turn the
video scope on/off separately on the desired video
output.
• By default, the video scope will appear on the right of
the screen. Using the > [
A
Assistance
Functions] > [Waveform Settings] or [Vectorscope
Settings] > [Position] settings, you can select where to display it (left or right side).
NOTES
NOTES
• The video scopes will also be displayed while adjusting a custom picture file's image settings (A 120).
Changing the Waveform Monitor Settings
1 Select > [
A
Assistance Functions] > [Waveform Settings] > [Type] > Desired option.
• If you selected an option other than [Select Line], skip to step 4.
2 Select > [
A
Assistance Functions] > [Waveform Settings] > [Select Line].
3 Enter the Y coordinate of the red horizontal line to display using the data entry screen (A 27).
• The available range of lines that can be selected depends on the vertical component of the resolution used.
For 2160: 0 to 2158 (in 2-line increments)
For 1080: 0 to 1079 (in 1-line increments)
For 720: 0 to 719 (in 1-line increments)
4 Select > [
A
Assistance Functions] > [Waveform Settings] > [Vertical Scale for HDR] >
Desired option.
• Select the Y axis (luminance) scale used when displaying the waveform monitor of an HDR image.
5 Select > [
A
Assistance Functions] > [Waveform Settings] > [Gain] > [1x] or [2x].
• If you selected [1x], the rest of the procedure is not necessary.
6 Select > [
A
Assistance Functions] > [Waveform Settings] > [Y Position] > Desired option.
• The display range of the waveform monitor’s Y axis will be reduced by half. Select the minimum luminance
value (in %) shown on the Y axis.