INSTRUCTION MANUAL E E The “Software Start Guide” is included at the end of this manual.
Introduction The EOS 5D Mark III is a high-performance, digital single-lens reflex camera featuring a fine-detail, full-frame (approx. 36 x 24 mm) CMOS sensor with approx. 22.3 effective megapixels, DIGIC 5+, approx. 100% viewfinder coverage, high-precision and high-speed 61-point AF, approx. 6 fps continuous shooting, Live View shooting, and Full HighDefinition (Full HD) movie shooting.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer.
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0, 9, 7, 8 : Indicates the Main Dial. : Indicates the Quick Control Dial. : Indicates the Multi-controller. : Indicates the Setting button. : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec. respectively after you let go of the button.
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.
Contents Introduction 2 Item Check List................................................................................. 3 Conventions Used in this Manual ..................................................... 4 Chapters........................................................................................... 5 Index to Features ........................................................................... 12 Handling Precautions .....................................................................
Contents 2 Basic Shooting 63 A Fully Automatic Shooting (Scene Intelligent Auto) ................... 64 A Full Auto Techniques (Scene Intelligent Auto) ......................... 67 3 Setting the AF and Drive Modes 69 f: Selecting the AF Mode ............................................................ 70 S Selecting the AF Area............................................................... 72 AF Area Selection Modes ...............................................................
Contents Noise Reduction Settings ............................................................. 143 Highlight Tone Priority .................................................................. 146 Lens Peripheral Illumination / Chromatic Aberration Correction........ 147 Creating and Selecting a Folder ................................................... 150 Changing the File Name............................................................... 152 File Numbering Methods ........................................
Contents 7 Shooting with the LCD Monitor (Live View Shooting) 197 A Shooting with the LCD Monitor ............................................... 198 Shooting Function Settings ........................................................... 202 Menu Function Settings ................................................................ 203 Using AF to Focus ........................................................................ 207 Focusing Manually ..............................................................
Contents k Enjoying Movies ..................................................................... 259 k Playing Movies ....................................................................... 261 X Editing the Movie’s First and Last Scenes .............................. 263 Slide Show (Auto Playback) ......................................................... 265 Viewing the Images on TV ........................................................... 268 K Protecting Images.........................................
Contents 13 Customizing the Camera 313 Custom Functions ......................................................................... 314 Custom Function Settings............................................................. 315 C.Fn1: Exposure ........................................................................ 315 C.Fn2: Disp./Operation .............................................................. 318 C.Fn3: Others.............................................................................
Index to Features Power Charging the battery Battery check Battery information check Power outlet Auto power off AF Î p.28 Î p.35 Î p.338 Î p.342 Î p.55 Card Format Î p.53 Select card Î p.116 Release shutter without card Î p.32 Î p.39 Î p.40 Î p.42 Î p.38 Î p.36 Î p.348 Î p.156 Î p.56 Viewfinder Dioptric adjustment Eyepiece cover Grid display Electronic level Î p.43 Î p.185 Î p.59 Î p.59 LCD Monitor Brightness adjustment Electronic level Feature guide 12 Metering Metering mode Î p.
Index to Features Chromatic aberration correction Color space Playback Î p.148 Î p.158 Shooting Shooting mode HDR Multiple exposures Mirror lockup Depth-of-field preview Remote control Quick Control Î p.24 Î p.173 Î p.177 Î p.184 Î p.165 Î p.186 Î p.49 Exposure Adjustment Exposure compensation AEB AE lock Safety shift Î p.169 Î p.170 Î p.171 Î p.317 Flash External flash External flash function settings External Speedlite Custom Functions Î p.187 Î p.191 Î p.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there may be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Quick Start Guide 1 2 Insert the battery (p.30). To charge the battery, see page 28. Insert a card (p.31). The camera-front side slot is for a CF card, and the camera-back side slot is for an SD card. 3 Attach the lens (p.39). 4 Set the lens focus mode switch to (p.39). 5 Set the power switch to <1> (p.34). 16 Align it with the red dot.
Quick Start Guide 6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto) (p.64). All the necessary camera settings will be set automatically. 7 Focus the subject (p.44). 8 Take the picture (p.44). 9 Review the picture (p.55). Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus the subject. Press the shutter button completely to take the picture.
Nomenclature AF mode selection/ Drive mode selection button (p.70/112) ISO speed setting/Flash exposure compensation button (p.124/188) LCD panel illumination button (p.48) Metering mode selection/ White balance selection button (p.167/137) AF area selection mode/ Multi-function button (p.73/188) Lens mount index (p.39) Flash-sync contacts Hot shoe (p.188) Mode Dial lock release button (p.45) <6> Main Dial (p.45) Shutter button (p.44) Mode Dial (p.24) Strap mount (p.
Nomenclature LCD panel (p.21, 22) Eyecup (p.185) Viewfinder eyepiece
AF start button (p.44, 70, 199, 226) AE lock button (p.171) AF point selection button (p.72) Info button (p.60, 61, 200, 225, 244, 336) Power switch (p.34) Quick Control button (p.49) Menu button (p.51) Terminal cover <5> Quick Control Dial (p.46) Date/time battery (p.343) Touch pad (p.46) <0> Setting button (p.51) External microphone IN terminal (p.235) Headphone terminal (p.
Nomenclature Focal plane mark Dioptric adjustment knob (p.43) Creative Photo/ Comparative playback (Two-image display)/ Direct print button (p.129, 173, 177/253/ 301) Live View shooting/ Movie shooting switch (p.197/217) <0> Start/Stop button (p.198, 218) <9> Multi-controller (p.47) Rating button (p.255, 273) Strap mount (p.27) Index/ Magnify/Reduce button (p.249/251) Card slot cover (p.31) Playback button (p.244) Erase button (p.
Nomenclature LCD Panel Shutter speed FE lock (FEL) Busy (buSY) Multi function lock warning (L) No card warning (Card) Error code (Err) Cleaning image sensor (CLn) White balance (p.137) Q Auto W Daylight E Shade R Cloudy Y Tungsten light U White fluorescent light I Flash O Custom P Color temperature Aperture AF point selection ([ -- -- -- ] AF, SEL [ ], SEL AF) AF point registration ([ -- -- -- ] HP, SEL [ ], SEL HP) Card warning (Card 1/2/1.
Nomenclature CF card indicator CF card selection icon ISO speed (p.124) ISO speed (p.124) Highlight tone priority (p.146) Exposure level indicator Exposure compensation amount (p.169) AEB range (p.170) Flash exposure compensation amount (p.188) Image-recording quality (p.119) 3 Large 4 Medium a Small 1 b Small 2 (Fine) c Small 3 (Fine) 1 RAW 41 Medium RAW 61 Small RAW 22 SD card selection icon SD card indicator AEB (p.170) Metering mode (p.
Nomenclature Viewfinder Information Spot metering circle (p.168) Focusing screen Grid (p.59) Area AF frame (p.73) Single AF point Spot AF (single point) (p.75) ISO speed (p.124) Warning symbol (p.318) Focus confirmation light (p.64) Battery check (p.35) AE lock (p.171) / AEB in-progress (p.170) Flash-ready (p.188) Improper FE lock warning AF status indicator (p.64) Max. burst (p.123) Number of remaining multiple exposures (p.179) ISO speed (p.124) FE lock (p.
Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). F : Bulb (p.172) a : Manual exposure (p.166) f : Aperture-priority AE (p.164) s : Shutter-priority AE (p.162) d : Program AE (p.160) A :Scene Intelligent Auto (p.64) Custom shooting modes You can register the shooting mode (d/s/f/a/F), AF mode, menu settings, etc., to w, x, y Mode Dial settings and shoot (p.332).
Nomenclature EF24-105mm f/4L IS USM lens Focus mode switch (p.39) Distance scale Infrared index Hood mount (p.41) 77 mm filter thread (front of lens) Zoom ring (p.40) Zoom position index (p.40) Focusing ring (p.111, 214) Contacts (p.15) Image Stabilizer switch (p.42) Lens mount index (p.
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.28). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. Battery Charger LC-E6E Charger for Battery Pack LP-E6 (p.28).
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap (p.185).
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Recharge the battery before using. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully-charged Battery Pack LP-E6 into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. the cover. 3 Close Press the cover until it snaps shut. Only Battery Pack LP-E6 can be used.
Installing and Removing the Card The camera can use a CF card and SD card. Images can be recorded when at least one card is installed in the camera. If a card is inserted in both slots, you can select which card to record images to or record the same images simultaneously on both cards (p.116, 118). If you use an SD card, be sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 CF card SD card Write-protect switch Open the cover.
Installing and Removing the Card the cover. 3 Close Close the cover and slide it in the Card selection icon Possible shots direction shown by the arrows until it snaps shut. X When you set the power switch to <1> (p.34), the number of possible shots and the loaded card(s) will be displayed on the LCD panel. The images will be recorded to the card with the < > icon next to the respective card’s indicator. CF card indicator SD card indicator The camera cannot use Type II CF cards or hard disk cards.
Installing and Removing the Card Removing the Card 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording ...] is displayed, close the cover. Access lamp the card. 2 Remove To remove the CF card, push the eject button. To remove the SD card, push it in gently and release it. Then pull it out. Pull the card straight out, then close the cover.
Turning on the Power If you turn on the power switch and the Date/Time/Zone setting screen appears, see page 36 to set the Date/Time/Zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera. About the Automatic Self-Cleaning Sensor Whenever you set the power switch to <1> or <2>, sensor cleaning will be executed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Icon Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 Battery Life 9-1 0 [Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time has been reset, the Date/Time/Zone setting screen will appear. Follow steps 3 to 6 to set the current date, time, and time zone. Note that the date/time appended to recorded images will be based on this date/time setting. Be sure to set the correct date/time. You can also set the time zone of your current address.
3 Setting the Date, Time, and Zone the date and time. 4 SetTurn the <5> dial to select the number. Press <0> so is displayed. Turn the <5> dial to select the desired setting, then press <0> (Returns to ). daylight saving time. 5 SetSettheif necessary. Turn the <5> dial to select [Y]. Press <0> so is displayed. Turn the <5> dial to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 3 will advance by 1 hour.
3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK]. Press the button and select the [5] tab. Turn the <6> dial to select the [52] tab. Turn the <5> dial to select [LanguageK] (the fourth item from the top), then press <0>. the desired language. 3 SetTurn the <5> dial to select the language, then press <0>. X The interface language will change.
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S lenses. 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the red dots on the lens and camera and turn the lens as shown by the arrow until it clicks in place. the lens focus mode switch to 3 Set . stands for Autofocus. If it is set to (manual focus), autofocus will not operate.
Attaching and Detaching a Lens Minimizing Dust When changing lenses, do it quickly in a place with minimal dust. When storing the camera without a lens attached, be sure to attach the body cap to the camera. Remove dust on the body cap before attaching it. About Zooming To zoom, turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus slightly.
Attaching and Detaching a Lens Attaching a Lens Hood When the dedicated EW-83H hood is attached to the EF24-105mm f/4L IS USM lens, it blocks stray light and protects the front of the lens from snow, rain, dust, etc. Before storing the lens in a bag, etc., you can attach the hood in reverse. 1 Align the red dots on the hood and lens edges. the hood as shown in the 2 Turn illustration. Turn the lens hood clockwise until it attaches securely.
About the Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF24-105mm f/4L IS USM lens as an example. * IS stands for Image Stabilizer. 1 Set the IS switch to <1>. Also set the camera’s power switch to <1>. the shutter button halfway. 2 Press X The Image Stabilizer will operate. the picture.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.185). If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens Eg (sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake. Horizontal shooting Vertical shooting 1.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0). Pressing completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for 6 seconds (9). During this time, you can turn the <6> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for 6 seconds (9). During this time, you can turn the <5> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select or set the white balance, drive mode, flash exposure compensation, AF point, etc. (2) Turn the <5> dial only.
Basic Operation 9 Multi-controller The <9> consists of an eight-direction key and a button at the center. Use it to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, operate the Quick Control screen, etc. You can also use it to select or set menu options (except [31: Erase images] and [51: Format card]).
Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Settings After you press the button a number of times, the shooting settings will be displayed. With the shooting settings displayed, you can turn the Mode Dial to see the settings for each shooting mode (p.337).
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called the Quick Control screen. 1 Press the button. X The Quick Control screen will appear (7). the desired function. 2 SetUse <9> to select a function. X The setting of the selected function is displayed at the bottom. Turn the <5> or <6> dial to change the setting. A mode d/s/f/a/F modes the picture. 3 TakePress the shutter button completely to take the picture.
Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen Auto Lighting Optimizer (p.142) Shutter speed (p.162) Aperture (p.164) AE lock* (p.171) Highlight tone priority* (p.146) Shooting mode* (p.24) ISO speed (p.124) Exposure compensation/ AEB setting (p.169, 170) Custom Controls (p.321) Picture Style (p.129) AF mode (p.70) White balance (p.137) Metering mode (p.167) White balance correction (p.140) Image-recording quality (p.119) Recording function/ Card selection (p.
3 Menu Operations With menus, you can set various functions such as the image-recording quality, date/time, etc. While looking at the LCD monitor, use the and buttons on the camera back and the <6> <5> dials. button LCD monitor <6> Main Dial button <5> Quick Control Dial <0> button A Mode Menu Screen * Some menu tabs and menu items are not displayed in the mode.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Each time you press the button, the main tab will switch. Turn the <6> dial to select a secondary tab. For example, the [z4] tab refers to the screen displayed when the z (Shooting) tab’s fourth dot from the left is selected. the desired item. 3 Select Turn the <5> dial to select the item, then press <0>. the setting.
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data in the card will be erased. As even protected images will be erased, make sure there is nothing you need to keep. If necessary, transfer the images to a personal computer, etc., before formatting the card. 1 Select [Format card]. Under the [51] tab, select [Format card], then press <0>. the card.
Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed (p.371). About Low-level Formatting Do low-level formatting if the SD card’s recording or reading speed seems slow or if you want to totally erase all data in the card.
Before You Start 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. If you do not want the camera to turn off automatically, set this to [Disable]. After the power turns off, you can turn on the camera again by pressing the shutter button or other buttons. 1 Select [Auto power off]. Under the [52] tab, select [Auto power off], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>.
Before You Start 3 Reverting the Camera to the Default SettingsN The camera’s shooting settings and menu settings can be reverted to their defaults. 1 Select [Clear all camera settings]. Under the [54] tab, select [Clear all camera settings], then press <0>. [OK]. 2 Select Select [OK], then press <0>.
Before You Start Image-recording Settings AF Settings Image quality 73 Picture Style Standard Auto Lighting Optimizer Standard Peripheral illumination correction Enable/ Correction data retained Chromatic aberration correction Enable/ Correction data retained USM lens electronic Enable after MF One-Shot AF White balance Q (Auto) Custom White Balance Canceled One-Shot AF release priority White balance correction Canceled Lens drive when AF Continue focus search impossible White balance b
Before You Start Camera Settings Live View Shooting Settings Auto power off 1 min. Live View shooting Enable Beep Enable AF mode Live mode Grid display Off Aspect ratio 3:2 Enable Release shutter without card Enable Image review 2 sec. Highlight alert Disable Exposure simulation AF point display Disable Silent LV shooting Mode 1 Histogram display Brightness Playback grid Magnification (Approx.) 2x Image jump w/6 Auto rotate Metering timer 16 sec.
Displaying the Grid and Electronic Level You can display a grid and electronic level in the viewfinder and on the LCD monitor to help correct camera tilt. Displaying the Grid in the Viewfinder 1 Select [VF grid display]. Under the [52] tab, select [VF grid display], then press <0>. [Enable]. 2 Select Turn the <5> dial to select [Enable], then press <0>. The grid will be displayed in the viewfinder.
Displaying the Grid and Electronic Level Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level. If the electronic level does not appear, set [53: z button display options] so that the electronic level can be displayed (p.336). the camera’s tilt. 2 Check The horizontal and vertical tilt are displayed in 1° increments. When the red line turns green, it indicates that the tilt is corrected.
Feature Guide When [zHelp] is displayed at the bottom of the menu screen, the Feature guide can be displayed. The Feature guide is displayed while you hold down the button. If the Feature guide fills two or more screens, a scroll bar will appear on the right edge. To scroll, hold down the button and turn the <5> dial.
Basic Shooting This chapter explains how to use the Mode Dial’s (Scene Intelligent Auto) mode for easy picture taking. In the mode, all you do is point and shoot and the camera sets everything automatically (p.346). Also, to prevent botched pictures due to mistaken operations, major shooting settings cannot be changed. Scene Intelligent Auto About the Auto Lighting Optimizer In the mode, the Auto Lighting Optimizer (p.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully-automatic mode. The camera analyzes the scene and sets the optimum settings automatically. Detecting whether the subject is still or moving, it also adjusts focus automatically. 1 Area AF frame Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. the Area AF frame over the 2 Aim target subject. All the AF points will be used to focus, and generally the closest object will be focused.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. X The captured image will be displayed for 2 sec. on the LCD monitor. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If you did not obtain the desired color tones, change the shooting mode to , set a Picture Style other than , then shoot again. FAQ The focus confirmation light blinks and focus is not achieved.
A Fully Automatic Shooting (Scene Intelligent Auto) The shutter speed display is blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (p.188) (sold separately) is recommended. When flash was used, the bottom part of the picture came out unnaturally dark. If a hood is attached to the lens, it can obstruct the flash coverage. If the subject is close, detach the hood before taking the picture with flash.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, while you press the shutter button halfway to focus a still subject, the focus will be locked. You can then recompose the shot and press the shutter button completely to take the picture. This is called “focus lock”.
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 197. 1 Set the Live View shooting/Movie shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. X The Live View image will appear on the LCD monitor. the subject. 3 Focus Aim the center AF point < > on the subject. Press the shutter button halfway to focus.
Setting the AF and Drive Modes The 61 AF points in the viewfinder make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF mode and drive mode that best match the shooting conditions and subject. A M icon at the upper right of a page title indicates that the function can be used when the Mode Dial is set to . In the mode, the AF mode and AF point (AF area selection mode) will be set automatically. stands for autofocus.
f: Selecting the AF ModeN You can select the AF mode to suit the shooting conditions or subject. In the mode, “AI Focus AF” is set automatically. 1 On the lens, set the focus mode switch to . 2 Press the button. (9) the AF mode. 3 Select While looking at the LCD panel, turn the <6> dial. X: One-Shot AF 9: AI Focus AF Z: AI Servo AF In the d/s/f/a/F shooting modes, AF is also possible by pressing the button. One-Shot AF for Still Subjects Suited for still subjects.
f: Selecting the AF ModeN If focus cannot be achieved, the focus confirmation light and AF status indicator in the viewfinder will blink. If this occurs, the picture cannot be taken even if the shutter button is pressed completely. Recompose the picture and try to focus again. Or see “When Autofocus Fails” (p.110). If [z1: Beep] is set to [Disable], the beeper will not sound when focus is achieved. After achieving focus with One-Shot AF, you can lock the focus on a subject and recompose the shot.
S Selecting the AF AreaN 61 AF points are provided for AF. You can select the AF point(s) suiting the scene or subject. Depending on the lens attached to the camera, the number of usable AF points and AF point patterns will differ. For details, see “Lenses and Usable AF Points” on page 79. AF Area Selection Mode You can select one of six AF area selection modes. See the next page for the selection procedure. Single-point Spot AF (Manual selection) For pinpoint focusing.
S Selecting the AF AreaN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and the surrounding AF points are used to focus. Zone AF (Manual selection of zone) The 61 AF points are divided into nine zones for focusing. 61-point automatic selection AF All the AF points are used to focus. This mode is set automatically in the mode. Select the AF Area Selection Mode Select the AF area selection mode. Press the button.
S Selecting the AF AreaN Selecting the AF Point Manually You can manually select the AF point or zone. With 61-point automatic selection AF, you can set the starting AF point for AI Servo AF. 1 Press the button. X The AF points will be displayed in the viewfinder. In AF point expansion modes, effective adjacent AF points will also be displayed. In the Zone AF mode, the selected zone will be displayed. an AF point. 2 Select The AF point selection will change in the direction you tilt the <9>.
AF Area Selection ModesN Single-point Spot AF (Manual selection) Although this is the same as single-point AF, the selected AF point covers a smaller area to focus. Effective for pinpoint focusing of overlapping subjects such as an animal in a cage. Since Spot AF covers a very small area, focusing may be difficult during hand-held shooting or for a moving subject. Single-point AF (Manual selection) Select one AF point to be used for focusing.
AF Area Selection ModesN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and adjacent AF points are used to focus. The AF point expansion is larger than with AF point expansion (Manual selection ), so the focusing is executed over a wider area. Effective when it is difficult to track a moving subject with just one AF point. AI Servo AF and One-Shot AF work in the same way as with AF point expansion (Manual selection ) mode (p.75).
AF Area Selection ModesN 61-point automatic selection AF All the AF points are used to focus. This mode is set automatically in the mode. With One-Shot AF, pressing the shutter button halfway will display the AF point(s) that achieved focus. If multiple AF points are displayed, it means they all have achieved focus. This mode tends to focus the nearest subject. With AI Servo AF, the manually-selected (p.74) AF point is used first to achieve focus.
About the AF Sensor The camera’s AF sensor has 61 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. With f/2.8 or larger maximum aperture lenses, high-precision AF is possible at the viewfinder center. Depending on the lens attached to the camera, the number of usable AF points and AF pattern will differ. For details, see pages 79 to 84. Diagram Cross-type focusing: f/4 horizontal + f/5.6 vertical Cross-type focusing: f/5.6 vertical + f/5.6 horizontal f/5.
Lenses and Usable AF Points Although the camera has 61 AF points, the number of usable AF points and focusing patterns will differ depending on the lens. The lenses are thereby classified into eight groups from A to H. Check which group your lens belongs to. When using a lens in Groups F to H, fewer AF points will be usable. When you press the button, the AF points indicated by the mark will blink. (The / / AF points will stay lit.) Both “Extender EF1.
Lenses and Usable AF Points EF400mm f/2.8L II USM EF400mm f/2.8L IS USM EF400mm f/2.8L IS II USM TS-E45mm f/2.8* TS-E90mm f/2.8* EF16-35mm f/2.8L USM EF16-35mm f/2.8L II USM EF17-35mm f/2.8L USM EF20-35mm f/2.8L EF24-70mm f/2.8L II USM EF28-70mm f/2.8L USM EF70-200mm f/2.8L USM EF70-200mm f/2.8L IS USM EF70-200mm f/2.8L IS II USM EF80-200mm f/2.8L * Manual focus without tilt/shift. Group B Autofocusing with 61 points is possible. All of the AF area selection modes are selectable.
Lenses and Usable AF Points EF50mm f/2.5 Compact Macro TS-E24mm f/3.5L* EF100mm f/2.8 Macro TS-E24mm f/3.5L II* EF100mm f/2.8L Macro IS USM EF300mm f/4L USM EF300mm f/4L IS USM EF400mm f/4 DO IS USM EF500mm f/4L IS USM EF500mm f/4L IS II USM EF600mm f/4L USM EF600mm f/4L IS USM EF600mm f/4L IS II USM TS-E17mm f/4L* EF200mm f/2.8L USM + Extender EF1.4x EF200mm f/2.8L II USM + Extender EF1.4x EF300mm f/2.8L USM + Extender EF1.4x EF300mm f/2.8L IS USM + Extender EF1.4x EF300mm f/2.
Lenses and Usable AF Points Group E Autofocusing with 61 points is possible. All of the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. EF50mm f/2.5 Compact Macro EF300mm f/2.8L IS II USM + LIFE SIZE Converter + Extender EF2x EF400mm f/2.8L USM EF100mm f/2.8 Macro USM + Extender EF2x EF400mm f/2.8L II USM EF400mm f/5.6L USM + Extender EF2x EF400mm f/2.8L IS USM EF500mm f/4.
Lenses and Usable AF Points EF70-200mm f/2.8L USM + Extender EF2x EF70-200mm f/2.8L IS USM + Extender EF2x EF70-200mm f/2.8L IS II USM + Extender EF2x EF70-200mm f/4L USM + Extender EF1.4x EF70-200mm f/4L IS USM + Extender EF1.4x EF70-210mm f/3.5-4.5 USM EF70-300mm f/4-5.6 IS USM EF70-300mm f/4-5.6L IS USM EF70-300mm f/4.5-5.6 DO IS USM EF80-200mm f/4.5-5.6 EF75-300mm f/4-5.6 EF90-300mm f/4.5-5.6 EF75-300mm f/4-5.6 USM EF90-300mm f/4.5-5.6 USM EF75-300mm f/4-5.6 II EF100-200mm f/4.
Lenses and Usable AF Points Group G Autofocusing with only 33 points is possible. (Not possible with all 61 AF points.) All of the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 61-point automatic selection AF. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. : Disabled AF points (not displayed). EF180mm f/3.
3 Selecting AI Servo AF Characteristics (For a Subject)N You can easily fine-tune AI Servo AF to suit a particular subject or scene just by selecting between case 1 to case 6. This feature is called the “AF Configuration Tool.” 1 Select the [21] tab. a case. 2 Select Turn the <5> dial to select a case icon, then press <0>. X The selected case will be set. The selected case is indicated in blue.
3 Selecting AI Servo AF Characteristics (For a Subject)N Case 1: Versatile multi purpose setting Default settings • Tracking sensitivity: [0] • Accel./decel. tracking: [0] • AF pt auto switching: [0] Standard setting suited for any moving subject. Works with many subjects and scenes.
3 Selecting AI Servo AF Characteristics (For a Subject)N Case 3: Instantly focus on subjects suddenly entering AF points Default settings • Tracking sensitivity: [Responsive: +1] • Accel./decel. tracking: [+1] • AF pt auto switching: [0] Once an AF point starts tracking the subject, this setting enables the camera to focus consecutive subjects at different distances. If a new subject appears in front of the target subject, the camera will start focusing the new subject.
3 Selecting AI Servo AF Characteristics (For a Subject)N Case 5: For erratic subjects moving quickly in any direction Default settings • Tracking sensitivity: [0] • Accel./decel. tracking: [0] • AF pt auto switching: [+1] Even if the target subject moves dramatically up, down, left, or right, the AF point will switch automatically to focus-track the subject. Effective for shooting subjects that move dramatically up, down, left, or right.
3 Selecting AI Servo AF Characteristics (For a Subject)N Case 6: For subjects that change speed and move erratically Default settings • Tracking sensitivity: [0] • Accel./decel. tracking: [+1] • AF pt auto switching: [+1] Geared for tracking moving subjects whose speed can change dramatically and suddenly. Also, if the target subject moves dramatically up, down, left or right and it is difficult to focus, the AF point switches automatically to track the subject.
3 Selecting AI Servo AF Characteristics (For a Subject)N About the Parameters Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. [0] Standard setting suited for most moving subjects. [Locked on: -2 / Locked on: -1] The camera will try to continue focusing the subject even if an obstacle enters the AF points or if the subject strays from the AF points.
3 Selecting AI Servo AF Characteristics (For a Subject)N Accel./decel. tracking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly, etc. [0] Suited for subjects that move at a fixed speed. [+2 / +1] Effective for subjects having sudden movements, sudden acceleration/deceleration, or sudden stops. Even if the moving subject’s speed suddenly changes dramatically, the camera continues to focus the target subject.
3 Selecting AI Servo AF Characteristics (For a Subject)N AF pt auto switching This sets the switching sensitivity of the AF points as they track the subject moving dramatically up, down, left, or right. This setting takes effect in the following AF area selection modes: AF point expansion (Manual selection ), AF point expansion (Manual selection, surrounding points), Zone AF (Manual selection), 61-point automatic selection AF. [0] Standard setting for gradual AF point switching.
3 Selecting AI Servo AF Characteristics (For a Subject)N Changing Cases’ Parameter Settings You can adjust each case’s three parameters (1. Tracking sensitivity, 2. Accel./decel. tracking, and 3. AF pt auto switching) as desired. 1 Select a case. Turn the <5> dial to select the icon of the case you want to adjust. the button. 2 Press The selected case will have a purple frame. the desired item. 3 Select Turn the <5> dial to select a parameter, then press <0>.
3 Customizing AF FunctionsN With the [22] to [25] menu tabs, you can set the AF functions to suit your shooting style or subject. 22: AI Servo AI Servo 1st image priority You can set the AF operation characteristics and shutter-release timing for the first shot during continuous shooting with AI Servo AF. : Equal priority Equal priority is given to focusing and shutter release. : Release priority Pressing the shutter button takes the picture immediately even if focus has not been achieved.
3 Customizing AF FunctionsN AI Servo 2nd image priority You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF. : Equal priority Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, shooting speed may slow down. : Shooting speed priority Priority is given to the continuous shooting speed instead of achieving focus. The continuous shooting speed does not slow down.
3 Customizing AF FunctionsN 23: One Shot USM lens electronic MF For the lenses below, which have an electronic focusing ring, you can set whether to use the electronic focusing ring. EF50mm f/1.0L USM EF85mm f/1.2L USM EF85mm f/1.2L II USM EF200mm f/1.8L USM EF300mm f/2.8L USM EF400mm f/2.8L USM EF400mm f/2.8L II USM EF500mm f/4.5L USM EF600mm f/4L USM EF1200mm f/5.6L USM EF28-80mm f/2.8-4L USM : Enable after One-Shot AF After AF operates, if you keep pressing the shutter button, you can focus manually.
3 Customizing AF FunctionsN AF-assist beam firing Enables or disables the EOS-dedicated Speedlite’s AF-assist beam. ON: Enable The external Speedlite emits the AFassist beam when necessary. OFF: Disable The external Speedlite will not emit the AF-assist beam. This prevents the AFassist beam from disturbing others. IR: IR AF assist beam only Among external Speedlites, only models with an infrared AF-assist beam will be able to emit the beam.
3 Customizing AF FunctionsN 24 Lens drive when AF impossible If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop searching. ON: Continue focus search If focus cannot be achieved with autofocus, the lens is driven to search for the correct focus. OFF: Stop focus search If autofocus starts and the focus is far off or if focus cannot be achieved, the lens drive stops.
3 Customizing AF FunctionsN : 15 points Fifteen major AF points will be manually selectable. : 9 points Nine major AF points will be manually selectable. With a lens from groups F to H (p.83, 84), the number of manually selectable AF points will be fewer. Even with settings other than [61 points], AF point expansion (Manual selection ), AF point expansion (Manual selection, surrounding points), and Zone AF (manual selection of Zone) are still possible.
3 Customizing AF FunctionsN : Manual select.:Zone AF The 61 AF points are divided into nine zones for focusing. : Auto selection: 61 pt AF All of the AF points are used for focusing. The mark cannot be deleted from [Manual selection:1 pt AF]. If the attached lens belongs to group H (p.84), you can only select [Manual select.:Spot AF] and [Manual selection:1 pt AF]. AF area selection method You can set the method for changing the AF area selection mode.
3 Customizing AF FunctionsN Orientation linked AF point You can set the AF area selection mode and manually-selected AF point separately for vertical shooting and horizontal shooting. : Same for both vert/horiz The same AF area selection mode and manually-selected AF point (or Zone) are used for both vertical shooting and horizontal shooting. : Select separate AF points The AF area selection mode and manually-selected AF point (or Zone) can be set separately for each camera orientation (1. Horizontal, 2.
3 Customizing AF FunctionsN 25 Manual AF point selection pattern During manual AF point selection, the selection can either stop at the outer edge or it can move to the opposite AF point. This function works in AF area selection modes other than 61-point automatic selection AF and Zone AF. (It works in 61-point automatic selection AF only with AI Servo AF.) : Stops at AF area edges Convenient if you often use an AF point along the edge.
3 Customizing AF FunctionsN If [Selected (pre-AF, focused)] or [Selected (focused)] is set, the AF point will not be displayed even when focus is achieved with AI Servo AF. VF display illumination The AF points and grid in the viewfinder can be illuminated in red when focus is achieved. AUTO: Auto The AF points and grid are automatically illuminated in red under low light. ON: Enable The AF points and grid are illuminated in red regardless of the ambient light level.
3 Fine Adjustment of AF’s Point of FocusN Fine adjustment of the AF’s point of focus is possible for viewfinder shooting and Live View shooting in the Quick mode. This is called “AF Microadjustment”. Before making the adjustment, read “Notes for AF Microadjustment” on page 109. Normally, this adjustment is not required. Do this adjustment only if necessary. Note that doing this adjustment may prevent correct focusing from being achieved.
3 Fine Adjustment of AF’s Point of FocusN the adjustment. 4 Make Turn the <5> dial to make the adjustment. The adjustable range is ±20 steps. Setting it toward “–: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to the rear of the standard point of focus. After making the adjustment, press <0>. Turn the <5> dial to select [All by same amount], then press <0>. The menu will reappear. the result of the 5 Check adjustment.
3 Fine Adjustment of AF’s Point of FocusN Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment has been registered, the point of focus will always be shifted by the adjustment amount. Set the adjustment manually by adjusting, shooting, and checking the result. Repeat this until the desired adjustment is made.
3 Fine Adjustment of AF’s Point of FocusN Enter the serial number. Turn the <5> dial to select the digit, then press <0> to display . Turn the <5> dial to enter the number, then press <0>. After entering all the digits, turn the <5> dial to select [OK], then press <0>. About the Lens Serial Number In step 3, if “ * ” appears in front of the 10-digit lens serial number, you cannot register several copies of the same lens model. Even if you enter the serial number, “ * ” will remain displayed.
3 Fine Adjustment of AF’s Point of FocusN Single focal length lens Zoom lens the adjustment. 4 Make For a zoom lens, turn the <5> dial and select the wide-angle (W) or telephoto (T) end. Pressing <0> will turn off the purple frame and make the adjustment possible. Turn the <5> dial to adjust as desired, then press <0>. The adjustable range is ±20 steps. Setting it toward “–: ” will shift the point of focus in front of the standard point of focus.
3 Fine Adjustment of AF’s Point of FocusN Clearing All AF Microadjustments When [ Clear all] appears at the bottom of the screen, pressing the button will clear all the adjustments made for [All by same amount] and [Adjust by lens]. Notes for AF Microadjustment The AF’s point of focus will vary slightly depending on the subject conditions, brightness, zoom position, and other shooting conditions.
When Autofocus Fails Autofocus can fail to achieve focus (viewfinder’s focus confirmation light blinks) with certain subjects such as the following: Subjects difficult to focus Very low-contrast subjects (Example: Blue sky, solid-color walls, etc.) Subjects in very low light Extremely backlit or reflective subjects (Example: Car with a highly reflective body, etc.) Near and far subjects covered by an AF point (Example: Animal in a cage, etc.
When Autofocus Fails MF: Manual Focusing 1 Set the lens focus mode switch to . X <4 L> will be displayed on the LCD panel. Focusing ring the subject. 2 Focus Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder. When you press the shutter button halfway while focusing manually, the focus confirmation light will light up when focus is achieved.
i Selecting the Drive Mode Single and continuous drive modes are provided. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel, turn the <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. o: High-speed continuous shooting (Max. approx. 6 shots/sec.) i : Low-speed continuous shooting (Max. approx. 3 shots/sec.) While you hold down the shutter button completely, shots will be taken continuously.
j Using the Self-timer If or is set, the time lag from when you press the shutter button completely until the picture is taken will be longer than normal. When the battery level is low, the continuous shooting speed may become slightly slower. o: The maximum continuous shooting speed of approx. 6 shots/sec. is attained under the following conditions*: At 1/500 sec. or faster shutter speed, and at the maximum aperture (varies depending on the lens).
j Using the Self-timer If you will not look through the viewfinder when you press the shutter button, attach the eyepiece cover (p.185). If stray light enters the viewfinder when the picture is taken, it may throw off the exposure. The enables you to shoot while not touching the camera mounted on a tripod. This prevents camera shake while you shoot still lifes or bulb exposures. After taking self-timer shots, playing back the image (p.244) to check focus and exposure is recommended.
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. A M icon at the upper right of a page title indicates that the function can be used when the Mode Dial is set to . * The function cannot be used in the mode.
3 Selecting the Card for Recording and Playback If either a CF card or SD card is already inserted, you can start shooting. When only one card is inserted, the procedures described on pages 116 to 118 are not necessary. If you insert both a CF card and SD card, you can select the recording method and select which card to use for recording and playing back images. Recording Method with Two Cards Inserted 1 Select [Record func+card/folder sel.]. Under the [51] tab, select [Record func+card/folder sel.
3 Selecting the Card for Recording and Playback Standard Images will be recorded to the card selected with [Record/play]. Auto switch card Same as with the [Standard] setting, but if the card becomes full, the camera will automatically switch to the other card to record images. When the camera switches to the other card, a new folder will be created automatically. Rec. separately You can set the image-recording quality for each card (p.119).
3 Selecting the Card for Recording and Playback Selecting the CF or SD Card for Recording and Playback If [Record func.] is set to [Standard] or [Auto switch card], select the card for recording and playing images. If [Record func.] is set to [Rec. separately] or [Rec. to multiple], select the card for playing images. If [Standard] or [Auto switch card] is set: Select [Record/play]. Turn the <5> dial to select [Record/ play], then press <0>. f : Record images to and play images back from the CF card.
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.122). 1 With [Standard / Auto switch card / Rec. to multiple] set: Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording 2 Select quality. To select a RAW setting, turn the <6> dial.
3 Setting the Image-Recording Quality Image-recording Quality Setting Examples 73 only 1 only 1 + 73 61 + 74 If [–] is set for both RAW and JPEG, 73 will be set. The number of possible shots will be displayed up to 1999 on the LCD panel.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Pixels Recorded (megapixels) Printing Size 22M A2 or larger 7.0 1010 65 (16270) 3.7 1930 1930 (30990) 9.8M A3 or larger 3.8 1860 1860 (29800) 2.0 3430 3430 (55000) 5.5M A4 or larger 2.5 2810 2810 (45140) 1.3 5240 5240 (83980) 1 b* 2.5M Around 9x13 cm 1.4 5030 5030 (80520) c*2 0.3M — 0.3 19520 19520 (312420) 1 22M A2 or larger 27.1 260 13 (18) 10M A3 or larger 19.
3 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded simultaneously to the card in both RAW and JPEG at the imagerecording quality that was set. The two images will be recorded with the same file numbers (file extension .JPG for JPEG and .CR2 for RAW). The image-recording quality icons are as follows: 1 (RAW), 41 (Medium RAW), 61 (Small RAW), JPEG, 7 (Fine), 8 (Normal), 3 (Large), 4 (Medium), and 6 (Small).
3 Setting the Image-Recording Quality One-touch Image Quality Setting With Custom Controls, you can assign the image-recording quality to the button or depth-of-field preview button so you can switch to it momentarily. If you assign [One-touch image quality setting] to the button or depth-of-field preview button, you can quickly switch to the desired image-recording quality and shoot. For details, see Custom Controls (p.321). If [51: Record func+card/folder sel.] is set to [Rec.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. With the mode selected, the ISO speed will be set automatically (p.125). Regarding the ISO speed during movie shooting, see pages 221 and 224. 1 Press the button. (9) the ISO speed. 2 SetWhile looking at the LCD panel or viewfinder, turn the <6> dial. ISO speed can be set within ISO 100 - 25600 in 1/3-stop increments. “A” indicates ISO Auto. The ISO speed will be set automatically (p.
i: Setting the ISO SpeedN As H1 (equivalent to ISO 51200) and H2 (equivalent to 102400) are expanded ISO speed settings, noise (dots of light, banding, etc.) and irregular colors will be more noticeable, and the resolution lower than usual. If you use a high ISO speed and flash to shoot a close subject, overexposure may result.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within L (ISO 50) to H1 (ISO 51200), and the maximum limit within ISO 100 to H2 (ISO 102400). 1 Select [ISO speed settings]. Under the [z2] tab, select [ISO speed settings], then press <0>. [ISO speed range]. 2 Select Select [ISO speed range], then press <0>. the minimum limit. 3 SetSelect the minimum limit box, then press <0>.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range for Auto ISO You can set the automatic ISO speed range for Auto ISO within ISO 100 - 25600. You can set the minimum limit within ISO 100 - 12800, and the maximum limit within ISO 200 - 25600 in whole-stop increments. 1 Select [Auto ISO range]. Select [Auto ISO range], then press <0>. the minimum limit. 2 SetSelect the minimum limit box, then press <0>. Turn the <5> dial to select the minimum limit ISO speed, then press <0>. the maximum limit.
i: Setting the ISO SpeedN 3 Setting the Minimum Shutter Speed for Auto ISO When Auto ISO is set, you can set the minimum shutter speed (1/250 sec. to 1 sec.) so that the automatically-set shutter speed is not too slow. This is convenient in the and modes when you use a wideangle lens to shoot a moving subject. You can minimize both camera shake and subject blur. 1 Select [Min. shutter spd.]. Select [Min. shutter spd.], then press <0>. the desired minimum shutter 2 Set speed.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. The Picture Style is set automatically to (Auto) in the mode. 1 Press the button. [A]. 2 Select Turn the <5> dial to select [A], then press <0>. X The Picture Style selection screen will appear. a Picture Style. 3 Select Turn the <5> dial to select the desired Picture Style, then press <0>.
A Selecting a Picture StyleN Picture Style Characteristics D Auto The color tone will be adjusted automatically to suit the scene. The colors will look vivid, especially for blue skies, greenery, and sunsets in nature, outdoor, and sunset scenes. P Standard The image looks vivid, sharp, and crisp. This is a general-purpose Picture Style suitable for most scenes. Q Portrait For nice skin tones. The image looks softer. Suited for close-up portraits. By changing the [Color tone] (p.
A Selecting a Picture StyleN V Monochrome Creates black-and-white images. Black-and-white images shot in JPEG cannot be reverted to color. If you want to later shoot pictures in color, make sure the [Monochrome] setting has been canceled. When [Monochrome] is selected, <0> will appear on the LCD panel. can be displayed in the viewfinder when [Monochrome] is set (p.318). W User Def. 1-3 You can register a basic style such as [Portrait], [Landscape], a Picture Style file, etc.
A Customizing a Picture StyleN You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see page 134. 1 Press the button. [A]. 2 Select Turn the <5> dial to select [A], then press <0>. X The Picture Style selection screen will appear. a Picture Style. 3 Select Turn the <5> dial to select the desired Picture Style, then press . a parameter.
A Customizing a Picture StyleN the parameter. 5 SetTurn the <5> dial to set the parameter as desired, then press <0>. Press the button to save the adjusted parameters. The Picture Style selection screen will reappear. X Any settings different from the default will be displayed in blue.
A Customizing a Picture StyleN V Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page. kFilter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. Filter Sample Effects N : None Normal black-and-white image with no filter effects. Ye: Yellow The blue sky will look more natural, and the white clouds will look crisper.
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create Picture Styles whose parameter settings such as sharpness and contrast are different. You can also adjust the parameters of a Picture Style that has been registered to the camera with EOS Utility (provided software, p.394). 1 Press the button. [A].
A Registering a Picture StyleN a parameter. 6 Select Turn the <5> dial to select a parameter such as [Sharpness], then press <0>. the parameter. 7 SetTurn the <5> dial to set the parameter as desired, then press <0>. For details, see “Customizing a Picture Style” on pages 132-134. Press the button to register the modified Picture Style. The Picture Style selection screen will then reappear. X The base Picture Style will be indicated on the right of [User Def. *].
B: Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the (Auto) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with , you can select the white balance to match the light source or set it manually by shooting a white object. is automatically set in the mode. 1 Press the button. (9) the white balance. 2 Select While looking at the LCD panel, turn the <5> dial.
B: Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Do this procedure under the actual light source to be used. 1 Photograph a white object. The plain, white object should fill the spot metering circle. Focus manually and set the standard exposure for the white object. You can set any white balance. Spot metering circle [Custom White Balance].
B: Setting the White BalanceN If the exposure obtained in step 1 differs greatly from the standard exposure, a correct white balance may not be obtained. In step 3, the following images cannot be selected: images captured while the Picture Style was set to [Monochrome], multiple-exposure images, and images taken with another camera. Instead of a white object, an 18% gray card (commercially available) can produce a more accurate white balance.
u White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters. White Balance Correction 1 Select [WB Shift/Bkt.]. Under the [z2] tab, select [WB Shift/Bkt.], then press <0>.
u White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images having a different color balance can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
3 Correcting the Brightness and Contrast AutomaticallyN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. [Standard] is automatically set in the mode. 1 Select [Auto Lighting Optimizer]. Under the [z2] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Noise Reduction SettingsN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the shadow areas is further reduced. 1 Select [High ISO speed NR]. Under the [z3] tab, select [High ISO speed NR], then press <0>. the desired setting. 2 SetTurn the <5> dial to select the desired noise reduction setting, then press <0>.
3 Noise Reduction SettingsN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z3] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetTurn the <5> dial to select the desired setting, then press <0>. X The setting screen closes and the menu will reappear. [Auto] For 1 sec.
3 Noise Reduction SettingsN With [Auto] and [Enable], after the picture is taken, the noise reduction process may take the same amount of time as the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1” or higher. Images taken at ISO 1600 or higher may look grainier with the [Enable] setting than with the [Disable] and [Auto] settings.
3 Highlight Tone PriorityN You can minimize overexposed highlight areas. 1 Select [Highlight tone priority]. Under the [z3] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Turn the <5> dial to select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. picture.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off occurs in lenses whose characteristics make the image corners look darker. Color fringing along subject outlines also is a chromatic aberration. Light fall-off and color fringing can be corrected. The default setting is [Enable] for both corrections. Peripheral Illumination Correction 1 Select [Lens aberration correction]. Under the [z1] tab, select [Lens aberration correction], then press <0>. the setting.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Turn the <5> dial to select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “About the Lens Correction Data” on the next page. picture. 2 TakeThetheimage will be recorded with the chromatic aberration corrected.
3 Lens Peripheral Illumination / Chromatic Aberration Correction About the Lens Correction Data The camera already contains lens peripheral illumination correction data and chromatic aberration correction data for approx. 25 lenses. If you select [Enable], the peripheral illumination correction and chromatic aberration correction will be applied automatically for any lens whose correction data has been registered in the camera.
3 Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This is optional since a folder will be created automatically for saving captured images. Creating a Folder 1 Select [Record func+card/folder sel.]. Under the [51] tab, select [Record func+card/folder sel.], then press <0>. [Folder]. 2 Select Turn the <5> dial to select [Folder], then press <0>. [Create folder]. 3 Select Turn the <5> dial to select [Create folder], then press <0>.
3 Creating and Selecting a Folder Selecting a Folder Lowest file number Number of images in folder With the folder selection screen displayed, turn the <5> dial to select the desired folder, then press <0>. X The folder where the captured images will be saved is selected. Subsequent captured images will be recorded into the selected folder.
3 Changing the File Name The file name has four alphanumeric characters followed by a four-digit image (Ex.) BE3B0001.JPG number (p.154) and extension. The first four alphanumeric characters are set upon factory shipment and unique to the camera. However, you can change them. With “User setting1”, you can change and register the four characters as desired. With “User setting2”, if you register three characters, the fourth character from the left will be appended automatically to indicate the image size.
3 Changing the File Name the setting. 4 ExitEnter the required number of alphanumeric characters, then press the button. X The new file name will be registered and the screen in step 2 will reappear. the registered file name. 5 Select Turn the <5> dial to select [File Settings name], then press <0>. Turn the <5> dial to select the registered file name, then press <0>. If User setting2 has been registered, select “*** (the 3 characters registered) + image size”.
3 File Numbering Methods The four-digit file number is like the frame number on a roll of film. The captured images (Ex.) BE3B0001.JPG are assigned a sequential file number from 0001 to 9999 and saved in one folder. You can change how the file number is assigned. 1 Select [File numbering]. Under the [51] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Turn the <5> dial to select the desired setting, then press <0>.
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. When you replace the card, create a folder, or switch the target card (such as f → g), the file numbering continues in sequence from 0001 for the images saved. This is convenient if you want to organize images according to cards or folders.
3 Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. 1 Select [Copyright information]. Under the [54] tab, select [Copyright information], then press <0>. the option to be set. 2 Select Turn the <5> dial, select either [Enter author’s name] or [Enter copyright details], then press <0>. text. 3 Enter Press the button, and the text palette will be highlighted in a color frame. Text can be entered.
3 Setting Copyright InformationN Checking the Copyright Information When you select [Display copyright info.] in step 2 on the preceding page, you can check the [Author] and [Copyright] information that you entered. Deleting the Copyright Information When you select [Delete copyright information] in step 2 on the preceding page, you can delete the [Author] and [Copyright] information. You can also set or check the copyright information with EOS Utility (provided software, p.394).
3 Setting the Color SpaceN The range of reproducible colors is called the color space. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. The color space is set automatically to sRGB in the mode. 1 Select [Color space]. Under the [z2] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>.
Advanced Operations In the d/s/f/a/F shooting modes, you can select the shutter speed, aperture, and other camera settings to change the exposure and obtain the desired result. AM icon at the upper right of a page title indicates that the function can be used when the Mode Dial is set to . * The function cannot be used in the mode. After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the LCD panel for 4 sec. (0).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for autoexposure. 1 Set the Mode Dial to . the subject. 2 Focus Look through the viewfinder and aim the AF point over the subject. Then press the shutter button halfway. X When focus is achieved, the focus confirmation light on the viewfinder’s bottom right will light up. (In One-Shot AF mode.
d: Program AE If the “30"” shutter speed and the maximum aperture blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the minimum aperture blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and Modes In the mode, many functions such the AF mode and metering mode are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen action (Fast shutter speed: 1/2000 sec.
s: Shutter-Priority AE If the maximum aperture blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the minimum aperture blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (higher aperture f/number) until the shutter speed blinking stops or set a lower ISO speed. Aperture Display The higher the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . speed and aperture. 2 SetTotheset shutter the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
q Selecting the Metering ModeN In [z2: Auto Lighting Optimizer], if the checkmark for [Disable during man expo] is removed, it can be set in the mode (p.142). When ISO Auto is set, you can press the button to lock the ISO speed. After recomposing the picture, you can see the exposure level difference on the exposure level indicator (p.22, 23) compared to when you pressed the button. q Selecting the Metering ModeN You can select one of four methods to measure the subject brightness.
q Selecting the Metering ModeN r Spot metering This is for metering a specific spot of the subject or scene. The metering is weighted at the center covering approx. 1.5% of the viewfinder area. e Center-weighted average metering The metering is weighted at the center and then averaged for the entire scene. When is set, can be displayed in the viewfinder (p.318).
Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z2] tab, select [Expo. comp./AEB], then press <0>. the AEB range. 2 SetTurn the <6> dial to set the AEB AEB range range. If you turn <5>, you can set the exposure compensation. Press <0> to set it.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the shot. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
F: Bulb Exposures When bulb is set, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the Mode Dial to . the desired aperture. 2 SetWhile looking at the LCD panel, turn the <6> or <5> dial. 3 Elapsed exposure time Take the picture.
w: HDR (High Dynamic Range) ShootingN You can take artistic photos having a high dynamic range and preserving detail in highlight and shadow areas. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured for each shot and then merged together automatically. The HDR image is recorded as a JPEG image. * HDR stands for High Dynamic Range. HDR Shooting 1 Press the button.
w: HDR (High Dynamic Range) ShootingN About Effects Natural For images preserving a wide tonal range where the highlight and shadow detail would otherwise be lost. Art standard While the highlight and shadow detail will be better preserved than with [Natural], the contrast will be lower and the gradation flatter to have the picture look like a painting. The subject outlines will have bright (or dark) edges.
w: HDR (High Dynamic Range) ShootingN [Continuous HDR]. 5 SetSelect either [1 shot only] or [Every shot], then press <0>. With [1 shot only], HDR shooting will be canceled automatically after the shooting ends. With [Every shot], HDR shooting continues until the setting in step 3 is set to [Disable HDR]. Image Align]. 6 SetFor[Auto handheld shooting, select [Enable]. When using a tripod, select [Disable]. Then, press <0>. to be saved.
w: HDR (High Dynamic Range) ShootingN Using a tripod is recommended. For handheld shooting, using a fast shutter speed is recommended. HDR shooting of a moving subject is not recommended because the movement of the subject will appear as afterimages in the merged image. HDR shooting is suited for still subjects. In HDR shooting, 3 images are captured with different shutter speeds set automatically.
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.197), you can see how the single exposures merge while shooting. 1 Press the button. multiple exposure. 2 Select Turn the <5> dial to select [P], then press <0>. X The multiple exposure setting screen will appear. [Multiple exposure]. 3 SetSelect [On:Func/Ctrl] or [On:ContShtng], then press <0>. To quit shooting multiple exposures, select [Disable].
P Multiple ExposuresN [Multi-expos ctrl]. 4 SetSelect the desired multiple-exposure control method, then press <0>. Additive The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation. Exposure Compensation Setting Guide for Multiple Exposures Two exposures: -1 stop, three exposures: -1.
P Multiple ExposuresN to be saved. 6 SetTothesaveimages all the single exposures and the merged multiple-exposure image, select [All images], then press <0>. To save only the merged multipleexposure image, select [Result only], then press <0>. [Continue Mult-exp]. 7 SetSelect either [1 shot only] or [Continuously], then press <0>. With [1 shot only], the setting in step 3 will be set automatically to [Disable]. Multiple-exposure shooting will be canceled automatically after the shooting ends.
P Multiple ExposuresN 9 Shoot subsequent exposures. X When [On:Func/Ctrl] is set, the merged multiple-exposure image will be displayed. With Live View shooting, the multiple-exposure images merged so far will be displayed. By pressing the button, you can display only the Live View image. After you shoot the set number of exposures, multiple-exposure shooting will be canceled.
P Multiple ExposuresN Merging multiple exposures with an image recorded in the card You can select an image recorded in the card as the first single exposure. The original of the selected image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images. 1 Select [Select image for multi. expo.]. Select [Select image for multi. expo.], then press <0>. X The images in the card will be displayed. an image.
P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single exposure. If you select [Deselect img], the selected image will be canceled. Checking and Deleting Multiple Exposures During Shooting When [On:Func/ctrl] is set and you have not finished shooting the set number of exposures, you can press the button to view the merged multiple-exposure image so far. You can check how it looks and the exposure. (Not possible when [On:ContShtng] is set.
P Multiple ExposuresN FAQ Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Image-Recording Quality Setting Single Exposures Merged MultipleExposure JPEG JPEG JPEG 1 1 1 41/61 41/61 1 1+JPEG 1+JPEG 1+JPEG 41/61+JPEG 41/61+JPEG 1+JPEG Can I merge images recorded in the card? With [Select image for multi. expo.
2 Mirror LockupN Although using the self-timer or Remote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). 1 Set [Mirror lockup] to [Enable]. Under the [z1] tab, select [Mirror lockup], then press <0>. Select [Enable], then press <0>. 2 Focus the subject, then press the shutter button completely. X The mirror will swing up, and the <2> icon will blink on the LCD panel.
Using the Eyepiece Cover When you use the self-timer or shoot bulb exposures and do not look through the viewfinder, stray light entering the viewfinder can cause the image to come out dark. To prevent this, use the eyepiece cover (p.27) attached to the camera strap. During Live View shooting and movie shooting, attaching the eyepiece cover is not necessary. 1 Remove the eyecup. While grasping both sides of the eyecup, slide it upward to remove. the eyepiece cover.
R Remote Control Shooting With Remote Controller RC-6 (sold separately), you can shoot remotely up to approx. 5 meters/16.4 feet from the camera. You can either shoot immediately or use a 2-sec. delay. You can also use Remote Controller RC-1 and RC-5. 1 Focus the subject. the lens focus mode switch to 2 Set . You can also shoot with . 3 Press the button. (9) the self-timer. 4 Select Look at the LCD panel and turn the <5> dial to select or .
Flash Photography This chapter explains how to shoot with an EOSdedicated, EX-series Speedlite (sold separately) or nonCanon flash unit and how to set flash functions on the camera’s menu screen.
D Flash Photography EOS-dedicated, EX-series Speedlites An EX-series Speedlite (sold separately) makes flash photography as easy as normal shooting. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions with the camera’s menu, see pages 191-196.
D Flash Photography Using Non-EX-series Canon Speedlites With an EZ/E/EG/ML/TL-series Speedlite set to A-TTL or TTL autoflash mode, the flash can be fired at full output only. Set the camera’s shooting mode to (manual exposure) or (aperture-priority AE) and adjust the aperture setting before shooting. When using a Speedlite that has manual flash mode, shoot in the manual flash mode. Using Non-Canon Flash Units Sync Speed The camera can synchronize with non-Canon compact flash units at 1/200 sec.
D Flash Photography If the camera is used with a flash unit or flash accessory dedicated to another camera brand, the camera may not operate properly and malfunction may result. Do not connect to the camera’s PC terminal any flash unit requiring 250 V or more. Do not attach a high-voltage flash unit on the camera’s hot shoe. It may not fire. A flash unit attached to the camera’s hot shoe and a flash unit connected to the PC terminal can both be used at the same time.
3 Setting the FlashN With an EX-series Speedlite having compatible flash function settings, you can use the camera’s menu screen to set the Speedlite’s functions and Custom Functions. Attach the Speedlite to the camera and turn on the Speedlite. For details on the Speedlite’s functions, refer to the Speedlite’s instruction manual. 1 Select [External Speedlite control]. Under the [z1] tab, select [External Speedlite control], then press <0>. X The external Speedlite control screen will appear.
3 Setting the FlashN [Flash sync. speed in Av mode] You can set the flash-sync speed for flash photography in the aperture-priority AE (f) mode. : Auto The flash sync speed is set automatically within a range of 1/200 sec. to 30 sec. to suit the scene’s brightness. High-speed sync is also possible. : 1/200-1/60 sec. auto Prevents a slow shutter speed from being set in low-light conditions. It is effective for preventing subject blur and camera shake.
3 Setting the FlashN [Flash function settings] On the screen, the settable functions and the display will differ depending on the Speedlite, current flash mode, flash Custom Function settings, etc. For details on your Speedlite’s flash functions, refer to the Speedlite’s instruction manual.
3 Setting the FlashN Wireless functions Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the Speedlite’s instruction manual. Flash zoom (Flash coverage) With Speedlites having a zooming flash head, you can set the flash coverage. Normally, set this to [AUTO] so that the camera will automatically set the flash coverage to match the lens focal length.
3 Setting the FlashN Flash exposure compensation The same setting as “Flash exposure compensation” on page 188 can be set. For details, refer to the Speedlite’s instruction manual. Flash exposure bracketing While the flash output is changed automatically, three shots are taken. For details on FEB (Flash Exposure Bracketing), refer to the Speedlite’s instruction manual. When using second-curtain synchronization, set the shutter speed to 1/25 sec. or slower. If the shutter speed is 1/30 sec.
3 Setting the FlashN Flash Custom Function Settings For details on the Speedlite’s Custom Functions, refer to the Speedlite’s instruction manual. 1 Select [Flash C.Fn settings]. Select [Flash C.Fn settings], then press <0>. the functions. 2 SetTurn the <5> dial to select the number, then press <0>. Turn the <5> dial to select the menu option, then press <0>. Clearing Flash Custom Function Settings Selecting [Clear all Speedlite C.Fn’s] will clear all the Speedlite’s Custom Function settings (except [C.
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . Live View shooting is effective for photos of still subjects. If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images. Using a tripod is recommended.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. X The Live View image will appear on the LCD monitor. The Live View image will closely reflect the brightness level of the actual image you capture. the subject. 3 Focus When you press the shutter button halfway, the camera will focus with the current AF mode (p.207). the picture. 4 TakePress the shutter button completely.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [z4: Live View shoot.] to [Enable]. In the mode, it is displayed under [z2]. Battery Life with Live View Shooting [Approx. number of shots] Temperature At 23°C / 73°F At 0°C / 32°F Possible shots 200 180 The figures above are based on a fully-charged Battery Pack LP-E6 and CIPA (Camera & Imaging Products Association) testing standards. With a fully-charged Battery Pack LP-E6, continuous Live View shooting is possible for approx.
A Shooting with the LCD Monitor About the Information Display Each time you press the button, the information display will change.
A Shooting with the LCD Monitor Final Image Simulation The final image simulation reflects the effects of the Picture Style, white balance, etc., in the Live View image so you can see what the captured image will look like. During shooting, the Live View image will automatically reflect the function settings listed below. Final image simulation during Live View shooting Picture Style * All parameters such as sharpness, contrast, color saturation, and color tone are reflected.
Shooting Function Settings i / y / f / R / B / S / A Settings While the Live View image is displayed, if you press the , , , , or button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function. When f is set, you can press the button to select the AF area selection mode and AF point. The procedure is the same as with viewfinder shooting. Note that the metering mode cannot be set.
3 Menu Function Settings Function settings particular to Live View shooting are explained here. The menu options under the [z4] tab are explained on pages 203-206. In the mode, it is displayed under [z2]. The functions settable on this menu screen only apply during Live View shooting. These functions do not take effect during viewfinder shooting. Live View shooting You can set Live View shooting to [Enable] or [Disable]. AF mode You can select [Live mode] (p.207), [u Live mode] (p.
3 Menu Function Settings Aspect ratioN The image’s aspect ratio can be set to [3:2], [4:3], [16:9], or [1:1]. The area surrounding the Live View image is masked in black when the following aspect ratios are set: [4:3] [16:9] [1:1]. JPEG images will be saved with the set aspect ratio. RAW images will always be saved with the [3:2] aspect ratio.
3 Menu Function Settings For asterisked image-recording quality, the pixel count does not exactly match the set aspect ratio. The image area displayed for the asterisked aspect ratio is slightly larger than the recorded area. Check the captured images on the LCD monitor when shooting. If you use a different camera to directly print images shot with this camera in the 1:1 aspect ratio, the images may not be correctly printed.
3 Menu Function Settings Silent LV shootingN • Mode 1 The shooting operation noise is quieter than with normal shooting. Continuous shooting is also possible. If is set, you can shoot at a maximum continuous shooting speed of approx. 6 fps. • Mode 2 When the shutter button is pressed completely, only one shot will be taken. While you keep holding down the shutter button, the camera operation will be suspended.
Using AF to Focus Selecting the AF Mode The AF modes available are [Live mode], [u Live mode] (face detection, p.208), and [Quick mode] (p.212). If you want to achieve precise focus, set the lens focus mode switch to , magnify the image, and focus manually (p.214). Select the AF mode. Under the [z4] tab, select [AF mode]. In the mode, it is displayed under [z2]. While the Live View image is displayed, you can press the button to select the AF mode on the setting screen displayed.
Using AF to Focus the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. X When focus is achieved, the AF point will turn green and the beeper will sound. X If focus is not achieved, the AF point will turn orange. the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.198). u (Face detection) Live Mode: c With the same AF method as the Live mode, human faces are detected and focused.
Using AF to Focus the subject. 2 Focus Press the shutter button halfway and the camera will focus the face covered by the
frame. X When focus is achieved, the AF point will turn green and the beeper will sound. X If focus is not achieved, the AF point will turn orange. If a face cannot be detected, the AF point < > will be displayed and AF will be executed at the center. the picture. 3 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.198).
Using AF to Focus Live Mode and u (Face Detection) Live Mode Notes AF operation Focusing will take slightly longer. Even when focus has been achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult. If this happens, stop the Live View shooting and autofocus under the actual light source.
Using AF to Focus Shooting conditions that can make focusing difficult Low-contrast subjects such as the blue sky and solid-color, flat surfaces. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Under a light source whose brightness, color, or pattern keeps changing. Night scenes or points of light. Under fluorescent or LED light sources or when the image flickers. Extremely small subjects. Subjects at the edge of the picture.
Using AF to Focus Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.70), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation. In AF area selection modes other than 61-point automatic selection AF, you can manually select the AF point or zone. In the mode, “61point automatic selection AF” is set automatically.
Using AF to Focus the AF point. 3 Select The AF point selection will change in the direction you tilt the <9>. If you press <9> straight down, the center AF point (or center Zone) will be selected. You can also use the <6> and <5> dials to select the AF point. The <6> dial selects an AF point in the horizontal direction, and the <5> dial selects an AF point in the vertical direction. the subject. 4 Focus Aim the AF point over the subject and press the shutter button halfway.
Focusing Manually You can magnify the image and focus precisely with manual focus. 1 Set the lens focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame. 2 Move Use <9> to move the magnifying Magnifying frame frame to the position where you want to focus. Pressing <9> straight down will return the magnifying frame to the image center. the image. 3 Magnify Press the button. X The area within the magnifying frame will be magnified.
Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (dots of light, banding, etc.) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a long period, the camera’s internal temperature may rise, degrading image quality. Stop Live View shooting when not shooting images. If you shoot a long exposure while the camera’s internal temperature is high, image quality may be degraded.
Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. If the light source within the image changes, the screen may flicker. If this happens, stop the Live View shooting and resume shooting under the actual light source to be used. If you point the camera in a different direction, it may throw off the Live View image’s correct brightness momentarily.
Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . The movie recording format will be MOV. Cards that can record movies When shooting movies, use a large-capacity card with a fast writing/reading speed as shown in the table. Compression Method (p.231) CF Card SD Card IPB 10 MB/sec. or faster 6 MB/sec. or faster ALL-I (I-only) 30 MB/sec. or faster 20 MB/sec.
k Shooting Movies Autoexposure Shooting When the shooting mode is set to , , or , autoexposure control will take effect to suit the scene’s current brightness. Exposure control will be the same for the three shooting modes. the Mode Dial to , , 1 Set or . the Live View shooting/Movie 2 Set shooting switch to . X The reflex mirror will make a sound, then the image will appear on the LCD monitor. the subject. 3 Focus Before shooting, focus with AF or manual focus (p.207-214).
k Shooting Movies Shutter-priority AE When the shooting mode is , you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired shutter speed. 3 SetWhile looking at the LCD monitor, turn the <6> dial. The settable shutter speeds depend on the frame rate <9>. • 6 5 4 : 1/4000 sec. - 1/30 sec.
k Shooting Movies Aperture-priority AE When the shooting mode is , you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired aperture. 3 SetWhile looking at the LCD monitor, turn the <6> dial. Aperture 4 Focus and shoot the movie.
k Shooting Movies ISO speed in the A mode In the A mode, the ISO speed will be set automatically within ISO 100 - 12800. ISO speed in the d, s, f, and F modes The ISO speed will be set automatically within ISO 100 - 12800. Under [z2: ISO speed settings] (p.126), if you set the [ISO speed range]’s [Maximum] setting to [25600/H] in the d, f, or F mode, the automatic ISO range will be expanded to H (equivalent to ISO 25600).
k Shooting Movies Notes for Autoexposure, Shutter-priority AE, and Aperture-priority AE You can lock the exposure (AE lock) by pressing the button (except in the A mode, p.171). After applying AE lock during movie shooting, you can cancel it by pressing the button. (AE lock setting is retained until you press ) You can set exposure compensation by setting the switch to the left and turning the <5> dial (except in the mode).
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. For details on the ISO speed, see the next page. the shutter speed and 4 Set aperture.
k Shooting Movies ISO speed during manual-exposure shooting With [Auto] (A), the ISO speed will be set automatically within ISO 100 - 12800. You can set the ISO speed manually within ISO 100 - 12800 in 1/3stop increments. Under [z2: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [25600/H], the maximum ISO speed for manual ISO speed setting will be expanded to H (equivalent to 25600).
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies Notes on Movie Shooting The camera cannot autofocus continuously like a camcorder. Autofocusing during movie shooting may momentarily throw the focus far off or change the exposure. During movie shooting, do not point the lens toward the sun. The sun’s heat can damage the camera’s internal components. Under [51: Record func+card/folder sel.], even if [Record func.] is set to [Rec. to multiple] (p.116), the movie cannot be recorded to both the CF card and SD card . If [Rec.
k Shooting Movies Notes on Movie Shooting By connecting stereo headphones (commercially available) equipped with a 3.5 mm mini plug to the camera’s headphone terminal (p.19), you can listen to the sound during movie shooting. You can use Remote Controller RC-6 (sold separately, p.186) to start and stop the movie shooting if the drive mode is or . Set the shooting timing switch to <2> (2-sec. delay), then press the transmit button.
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking still photos during movie shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx. 1 sec. The captured still photo will be recorded to the card, and the movie shooting will resume automatically when the Live View image is displayed. The movie and still photo will be recorded as separate files on the card.
k Shooting Movies AEB cannot be used. Even if an external Speedlite is used, it will not fire. Continuous still photo shooting is possible during movie shooting. However, the captured images will not be displayed on the screen. Depending on the still photo’s image-recording quality, number of shots during continuous shooting, card performance, etc., movie shooting may stop automatically. If [z5: Movie shoot. btn] is set to [V/ ], you cannot take still photos.
Shooting Function Settings f / R / B / i / S / A Settings If you press the , , , , or button while the image is displayed on the LCD monitor, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective function. When f is set, you can press the button to select the AF area selection mode and AF point. The procedure is the same as with viewfinder shooting. During manual-exposure shooting (p.
3 Setting the Movie-Recording Size With [z4: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. In the mode, these menu options are displayed under [z2]. Image size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9. B [1280x720] : High-Definition (HD) recording quality. The aspect ratio will be 16:9.
3 Setting the Movie-Recording Size Total Movie Recording Time and File Size Per Minute Total Recording Time (approx.) Movie-Recording Size 4 GB Card 8 GB Card 16 GB Card File Size (approx.) 654 X 16 min. 32 min. 1 hr. 4 min. 235 MB/min. 654 W 5 min. 11 min. 22 min. 685 MB/min. 87 X 18 min. 37 min. 1 hr. 14 min. 205 MB/min. 87 W 6 min. 12 min. 25 min. 610 MB/min. C 65 X 48 min. 1 hr. 37 min. 3 hr. 14 min. 78 MB/min.
3 Setting the Movie-Recording Size An increase of the camera’s internal temperature may cause movie shooting to stop before the maximum recording time shown in the preceding page (p.241). Even if [Record func.] is set to [Auto switch card], the card cannot be switched automatically during movie shooting. About Full HD 1080 Full HD 1080 indicates compatibility with High-Definition featuring 1080 vertical pixels (scanning lines).
3 Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or a commercially-available stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [z4: Sound recording]. In the mode, this setting is displayed in [z2]. Sound Recording/Sound-Recording Level [Auto] [Manual] [Disable] : The sound-recording level is adjusted automatically.
3 Setting the Sound Recording Using the microphone The built-in microphone records monaural sound. Stereo sound recording is possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (3.5 mm) to the camera’s external microphone IN terminal (p.19). When an external microphone is connected, sound recording will switch automatically to the external microphone. Using headphones By connecting stereo headphones (commercially available) equipped with a 3.
3 Silent Control This function is convenient when you want to change the ISO speed, soundrecording level, etc., silently while shooting a movie. When [z5: Silent Control] is set to [Enable h], you can use the touch pad on the inner ring of the Quick Control Dial. In the mode, this function is displayed in [z3]. You can just touch the top, bottom, left, or right of for silent operation.
3 Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Set the time code with [z5: Time code]. In the mode, this function is displayed in [z3]. Count Up [Rec run] : The time code counts up only while you are shooting a movie.
3 Setting the Time Code Regardless of the [Movie rec count] setting, the time code will always be recorded to the movie file. Movie Playback Count You can select what to display on the movie playback screen. [Rec time] : Displays the recording time and playback time during movie playback. [Time code] : Displays the time code during movie playback.
3 Menu Function Settings [z4] Menu When the Live View shooting/Movie shooting switch is set to , the [z4] and [z5] tabs dedicated to movie shooting will be displayed. The menu options are as follows. In the mode, [z2] and [z3] will be displayed. AF mode The AF modes will be the same as described on pages 207-213. You can select [Live mode], [u Live mode], or [Quick mode]. Note that continuous focusing of a moving subject is not possible.
3 Menu Function Settings Silent LV shootingN This function applies to still photo shooting. For details, see page 206. Metering timerN You can change how long the exposure setting is displayed (AE lock time). [z5] Menu Time code You can set the time code. For details, see pages 237 and 238. Silent Control When [Enable h] is set, you can use the touch pad and Quick Control screen to change settings silently during movie shooting. For details, see page 236.
Movie Shooting Cautions White and Red Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or a high ambient temperature, a white icon will appear. Even if you shoot a movie while this icon is displayed, the movie’s image quality will hardly be affected. However, if you shoot still photos, the image quality of the still photos may degrade. You should stop shooting still photos for a while and allow the camera to cool down.
Movie Shooting Cautions Recording and Image Quality If you use a card having a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator becomes full, movie shooting will stop automatically.
Image Playback This chapter explains how to play back and erase photos and movies, how to display them on a TV screen, and other playback-related functions. About images taken with another camera The camera may not be able to properly display images captured with a different camera or edited with a computer or whose file name was changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. X The last captured image or last image viewed will appear. an image. 2 Select To play back images starting with the last image, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the display format will change.
x Image Playback the image playback. 3 ExitPress the button to exit the image playback and return to shooting-ready state. 3 Grid Display In single-image display and two-image display (p.253) display, you can overlay the grid on the image playback. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag n]. This function is convenient for checking the image’s tilt and composition. The grid is not displayed during movie playback.
B: Shooting Information Display Sample Information for Still Photos AF Microadjustment Exposure compensation amount Flash exposure compensation amount Aperture Protect images Rating Folder number - File number Card Histogram (Brightness/RGB) Shutter speed Picture Style/Settings Metering mode Shooting mode ISO speed Highlight tone priority White balance Image-recording quality Playback number/ Total images recorded Color temperature when
is set Color space Shooting date and time White balance corr
B: Shooting Information Display Sample Information for Movies Shooting time, Playback time/ Time code Playback Shutter speed Aperture Shooting mode Movie file size Movie recording size Frame rate Compression method About the Highlight Alert When [33: Highlight alert] is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again. About the AF Point Display When [33: AF point disp.
B: Shooting Information Display About the Histogram The brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram is for checking the color saturation and gradation. The display can be switched with [33: Histogram disp]. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) You can search for images quickly with the index display showing four or nine images on one screen. 1 Press the button. During image playback, press the button. X [6u] will be displayed on the lower right of the screen. to the index display. 2 Switch Turn the <6> dial counterclockwise. X The 4-image index display will appear. The currently-selected image will be highlighted in a blue frame.
x Searching for Images Quickly I Jump through Images (Jump Display) With the single image display, you can turn the <6> dial to jump through the images forward or back according to the jump method set. 1 Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>. the jump method. 2 Select Turn the <5> dial to select the jump method, then press <0>.
u Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. 1 Magnified area position Magnify the image. The image can be magnified during image playback (single-image display), during image review after image capture, and from shooting-ready state. Press the button. X The magnified view will appear. The magnified area and [6u] will be displayed on the lower right of the screen. The image magnification increases as you turn the <6> dial clockwise.
u Magnified View 3 Magnification Settings Under the [33] tab, when you select [Magnificatn (apx)], you can set the starting magnification and initial position for the magnified view. 1x (no magnification) The image will not be magnified. The magnified view will start with the single-image display. 2x, 4x, 8x, 10x (magnify from center) The magnified view will start at the image center at the selected magnification. Actual size (from selected point) The recorded image’s pixels will be displayed at approx.
X Comparing Images (Two-Image Display) You can compare two images side by side on the LCD monitor. 1 Set the two-image display. During image playback, press the button. X Two images will be displayed. The currently-selected image will be highlighted in a blue frame. the images to be 2 Select compared. Pressing <0> switches the blue frame between the two images. Turn the <5> dial to select an image. Repeat step 2 to select the other image to be compared.
b Rotating the Image You can rotate the displayed image to the desired orientation. 1 Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. an image. 2 Select Turn the <5> dial to select the image to be rotated. You can also select an image on the index display (p.249). the image. 3 Rotate Each time you press <0>, the image will rotate clockwise as follows: 90° → 270° → 0° To rotate another image, repeat steps 2 and 3. Press the button to return to the menu.
Setting Ratings You can rate images and movies with one of five rating marks: l/m/ n/o/p. This function is called rating. Set ratings with the Button 1 Select an image or movie. During image playback, turn the <5> dial to select an image or movie to be rated. You can also select an image or movie on the index display (p.249). or movie. 2 RateEachthetimeimage you press the button, the rating mark will change: l/m/n/o/p/None. To rate another image or movie, repeat steps 1 and 2.
Setting Ratings an image or movie. 2 Select Turn the <5> dial to select the image or movie to be rated. If you press the button and turn the <6> dial counterclockwise, you can select an image or movie from a three-image display. To return to the single-image display, turn the <6> dial clockwise. the image or movie. 3 RatePressing <0> will turn off the [s] icon. Turn the <5> dial to select a rating. X The total number of images and movies rated will be counted for each rating.
Q Quick Control During Playback During playback, you can press the button to set the following: [K: Protect images, b: Rotate image, 9: Rating, R: RAW image processing (RAW images only), S: Resize (JPEG image only), : Highlight alert, :AF point display, e: Image jump w/6]. For movies, only the functions in bold above can be set. 1 Press the button. During image playback, press the button. X The Quick Control screen will appear. a function and set it.
Q Quick Control During Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the button during the index display will switch to the single-image display and the Quick Control screen will appear. Pressing the button again will return to the index display.
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV set (p.268, 271) Use the provided AV cable or an HDMI Cable HTC-100 (sold separately) to connect the camera to a TV set. Then you can play back captured movies and still photos on the TV. If you have a High-Definition TV set and connect your camera with an HDMI cable, you can watch Full High-Definition (Full HD: 1920x1080) and HighDefinition (HD: 1280x720) movies with higher image quality.
k Enjoying Movies Playback and Editing with a Personal Computer (p.394) The movie files recorded on the card can be transferred to a personal computer and played with ImageBrowser EX. To have the movie play back smoothly on a personal computer, use a high-performance personal computer. Regarding the computer hardware requirements for ImageBrowser EX, refer to the PDF file ImageBrowser EX User Guide.
k Playing Movies 1 Play back the image. Press the button to display images. a movie. 2 Select Turn the <5> dial to select the movie to be played. With the single-image display, the <1s> icon displayed on the upper left indicates a movie. On the index display, the perforations on the left edge of the image indicates a movie. As movies cannot be played on the index display, press <0> to switch to the single-image display. the single-image display, 3 On press <0>.
k Playing Movies Function Playback Description 2 Exit Returns to the single-image display. 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by turning the <5> dial. The slow-motion speed is indicated on the upper right. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie.
X Editing the Movie’s First and Last Scenes You can edit out the first and last scenes of a movie in 1-sec. increments. 1 On the movie playback screen, select [X]. X The movie editing panel will be displayed at the bottom of the screen. the part to be edited out. 2 Specify Select either [U] (Cut beginning) or [V] (Cut end), then press <0>. Tilt <9> to the left or right to see the previous or next frames. Holding it down will fast forward the frames. Turn the <5> dial for frame-byframe playback.
X Editing the Movie’s First and Last Scenes the movie. 4 Save Select [W], then press <0>. X The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite]. Then press <0>. On the confirmation screen, select [OK], then press <0> to save the edited movie and return to the movie playback screen. Since the editing is performed in 1-sec.
3 Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. 1 Number of images to be played Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. the images to be played. 2 Select Turn the <5> dial to select the desired option, then press <0>. [All images/Movies/Stills] Turn the <5> dial to select one of the following: [jAll images/ kMovies/zStills]. Then press <0>.
3 Slide Show (Auto Playback) Item Playback Description jAll images All the still photos and movies on the card will be played back. iDate Still photos and movies taken on the selected shooting date will be played back. nFolder Still photos and movies in the selected folder will be played back. kMovies Only the movies on the card will be played back. zStills Only the still photos on the card will be played back.
3 Slide Show (Auto Playback) show. 4 StartTurnthetheslide <5> dial to select [Start], then press <0>. X After [Loading image...] is displayed, the slide show will start. slide show. 5 QuitTo the quit the slide show and return to the setting screen, press the button. To pause the slide show, press <0>. During pause, [G] will be displayed on the upper left of the image. Press <0> again to resume the slide show.
Viewing the Images on TV You can view the still photos and movies on a TV set. Adjust the movie’s sound volume with the TV set. The sound volume cannot be adjusted with the camera. Before connecting or disconnecting the cable between the camera and television, turn off the camera and TV set. Depending on the TV set, part of the image displayed may be cut off. Viewing on High-Definition (HD) TV Sets HDMI Cable HTC-100 (sold separately) is required. 1 Connect the HDMI cable to the camera.
Viewing the Images on TV the button. 5 Press X The image will appear on the TV screen. (Nothing will be displayed on the camera’s LCD monitor.) The images will automatically be displayed at the TV’s optimum resolution. By pressing the button, you can change the display format. To play back movies, see page 261. The movie cannot be output at the same time from both the and terminals. Do not connect any other device’s output to the camera’s terminal. Doing so may cause a malfunction.
Viewing the Images on TV the camera to a TV set. 2 Connect Use an HDMI cable to connect the camera to the TV. X The TV’s input will switch automatically to the HDMI port connected to the camera. the camera’s button. 3 Press X An image will appear on the TV screen and you can use the TV’s remote control to play back images. an image or movie. 4 Select Point the remote control toward the TV set and press the / button to select an image. Still photo playback menu the remote control’s Enter button.
Viewing the Images on TV Viewing on Non High-Definition (HD) TV Sets 1 Connect the provided AV cable to the camera. With the plug’s logo facing the back of the camera, insert it into the terminal. (Red) (White) (Yellow) the AV cable to the TV 2 Connect set. Connect the AV cable to the TV’s video IN terminal and audio IN terminal. on the TV and switch the 3 Turn TV’s video input to select the connected port. the camera’s power switch to 4 Set <1>. the button.
K Protecting Images Protecting an image prevents it from being erased accidentally. 3 Protecting a Single Image 1 Select [Protect images]. Under the [31] tab, select [Protect images], then press <0>. [Select images]. 2 Select Select [Select images], then press <0>. X The images will be displayed. Image protect icon the image. 3 Protect Turn the <5> dial to select the image to be protected, then press <0>. X The image will be protected, and the icon will appear at the top of the screen.
K Protecting Images 3 Protecting All Images in a Folder or Card You can protect all the images in a folder or on a card at one time. Under [31: Protect images], when you select [All images in folder] or [All images on card], all the images in the folder or on a card will be protected. To cancel the image protection, select [Unprotect all images in folder] or [Unprotect all images on card]. Set with the Button During image playback, you can use the button to protect an image.
a Copying Images The images recorded on one card can be copied to the other card. 3 Copying Individual Images 1 Select [Image copy]. Under the [31] tab, select [Image copy], then press <0>. [Sel.Image]. 2 Select Check the copy source and target card’s capacity. Turn the <5> dial to select [Sel.Image], then press <0>. Lowest file number Number of images in folder the folder. 3 Select Turn the <5> dial to select the folder containing the image to be copied, then press <0>.
a Copying Images Total images selected the images to be copied. 4 Select Turn the <5> dial to select an image to be copied, then press <0>. X The icon will appear on the upper left of the screen. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the <6> dial clockwise. To select other images to be copied, repeat step 4. the button.
a Copying Images [OK]. 8 Select Check the copy source and target card’s information. Turn the <5> dial to select [OK], then press <0>. X The copying will start and the progress will be displayed. When the copying is completed, the result will be displayed. Select [OK] to return to the screen in step 2. 3 Copying All Images in a Folder or Card You can copy all the images in a folder or on a card at one time. Under [x1: Image copy], when you select [Sel.
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images (p.272) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button.
L Erasing Images [Select and erase images]. 2 Select Select [Select and erase images], then press <0>. X The images will be displayed. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6> dial clockwise. the images to be erased. 3 Select Turn the <5> dial to select the image to be erased, then press <0>. X A checkmark will be displayed on the upper left.
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness The LCD monitor’s brightness is adjusted automatically for optimum viewing. You can set the automatic adjustment’s brightness level (brighter or darker) or adjust the brightness manually. 1 Select [LCD brightness]. Under the [52] tab, select [LCD brightness], then press <0>. [Auto] or [Manual]. 2 Select Turn the <6> dial to make the selection. the brightness.
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the personal computer instead of horizontally. The setting of this feature can be changed. 1 Select [Auto rotate]. Under the [51] tab, select [Auto rotate], then press <0>. the auto rotation. 2 SetSelect the desired option, then press <0>.
Post-Processing Images You can process RAW images with the camera or resize (shrink) JPEG images. A M icon at the upper right of a page title indicates that the function can be used when the Mode Dial is set to . * The function cannot be used in the mode. The camera may not be able to process images taken with another camera.
R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. While the RAW image itself does not change, you can process the RAW image according to different conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera. Use Digital Photo Professional (provided software, p.394) to process those images. 1 Select [RAW image processing].
R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the setting screen. Turn the <5> or <6> dial to change the setting. To return to the screen in step 3, press <0>. the image. 4 Save Select [W] (Save), then press <0>. Select [OK] to save the image. Check the destination folder and image file number, then select [OK]. To process another image, repeat steps 2 to 4. Press the button to return to the menu.
R Processing RAW Images with the CameraN RAW Image-processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance (p.137) You can select the white balance. If you select [P], turn the <6> dial to set the color temperature on the setting screen. The displayed image will reflect the setting’s effect. Picture Style (p.129) You can select the Picture Style.
R Processing RAW Images with the CameraN Color space (p.158) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.147) If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, press the button to magnify the image and check the corners. (Press the button to return to the normal view.
R Processing RAW Images with the CameraN Chromatic aberration correction When [Enable] is set, the lens’ chromatic aberrations (color fringing along the subject’s outline) can be corrected. If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, press the button to magnify the image. (Press the button to return to the normal view.
S Resize You can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/4/a/b images. JPEG c and RAW images cannot be resized. 1 Select [Resize]. Under the [32] tab, select [Resize], then press <0>. X The images will be displayed. an image. 2 Select Turn the <5> dial to select the image you want to resize. If you press the button and turn the <6> dial counterclockwise, you can select an image from the index display.
S Resize Resize Options According to Original Image Size Original Image Size 3 Available Resize Settings 4 a b c k k k k k k k k k 4 a k b About Image Sizes The image size displayed in step 3 on the preceding page, such as [**M ****x****], has a 3:2 aspect ratio. The image size according to aspect ratios is shown in the table below. The asterisked image-recording quality figures do not exactly match the aspect ratio. The image will be cropped slightly.
Sensor Cleaning The camera has a Self Cleaning Sensor Unit attached to the image sensor’s front layer (low-pass filter) to shake off dust automatically. The Dust Delete Data can also be appended to the image so that the dust spots remaining can be erased automatically by Digital Photo Professional (provided software, p.394).
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation. However, you can choose to perform sensor cleaning at any time, or disable it. Cleaning the Sensor Now 1 Select [Sensor cleaning]. Under the [53] tab, select [Sensor cleaning], then press <0>. [Clean nowf]. 2 Select Select [Clean nowf], then press <0>.
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later. The Dust Delete Data is used by Digital Photo Professional (provided software, p.394) to erase the dust spots automatically. Preparation Prepare a solid white object such as a sheet of paper. Set the lens focal length to 50 mm or longer.
3 Appending Dust Delete DataN a solid-white object. 3 Photograph At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in aperturepriority AE mode at an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no card in the camera. X When the picture is taken, the camera will start collecting the Dust Delete Data.
3 Manual Sensor CleaningN Dust that could not be removed by the automatic sensor cleaning can be removed manually with a blower, etc. Before cleaning the sensor, detach the lens from the camera. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. 1 Select [Sensor cleaning]. Under the [53] tab, select [Sensor cleaning], then press <0>. [Clean manually]. 2 Select Select [Clean manually], then press <0>.
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. Doing any of the following will cut off the power and close the shutter. The shutter curtains and image sensor may then get damaged. • Setting the power switch to <2>. • Removing or inserting the battery. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor.
Printing Images and Transferring Images to a Computer Printing (p.298) You can connect the camera directly to a printer and print out the images on the card. The camera is compatible with “wPictBridge” which is the standard for direct printing. Digital Print Order Format (DPOF) (p.305) DPOF (Digital Print Order Format) enables you to print images recorded on the card according to your printing instructions such as the image selection, quantity to print, etc.
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the LCD monitor. Connecting the Camera to a Printer 1 Set the camera’s power switch to <2>. the printer. 2 SetForupdetails, refer to the printer’s instruction manual. the camera to the 3 Connecting printer. Use the interface cable provided with the camera. Connect the cable to the camera’s terminal with the cable plug’s icon facing the front of the camera.
Preparing to Print wPictBridge back the image. 6 PlayPress the button. X The image will appear, and the icon will appear on the upper left to indicate that the camera is connected to a printer. Movies cannot be printed. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct. Do not use any interface cable other than the one provided. If there is a long beeping sound in step 5, it indicates a problem with the printer.
wPrinting The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon 1 Select the image to be printed. Check that the icon is displayed on the upper left of the LCD monitor. Turn the <5> dial to select the image to be printed. <0>. 2 Press X The print settings screen will appear. Print setting screen Sets the printing effects (p.300).
wPrinting Q Setting the Paper Size Select the size of the paper loaded in the printer, then press <0>. X The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in the printer, then press <0>. X The page layout screen will appear. U Setting the Page Layout Select the page layout, then press <0>. X The print settings screen will reappear. Bordered The print will have white borders along the edges. Borderless The print will have no borders.
wPrinting printing effects. 4 SetSettheif necessary. If you do not need to set any printing effects, go to step 5. What is displayed on the screen differs depending on the printer. Select the option, then press <0>. Select the desired printing effect, then press <0>. If the icon is displayed brightly next to , you can also adjust the printing effect (p.302). Printing Effect Description EOn The image will be printed according to the printer’s standard colors.
wPrinting the date and file number 5 Set imprinting. Set if necessary. Select , then press <0>. Set as desired, then press <0>. number of copies. 6 SetSettheif necessary. Select , then press <0>. Set the number of copies, then press <0>. printing. 7 StartSelect [Print], then press <0>. With Easy printing, you can print another image using the same settings. Just select the image and press the button. With Easy printing, the number of copies will always be 1.
wPrinting e Adjustment of Printing Effects In step 4 on page 300, select the printing effect. When the icon is displayed brightly next to , you can press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels When you select [Manual], you can change the histogram’s distribution and adjust the image’s brightness and contrast.
wPrinting Trimming the Image Tilt correction You can crop the image and print only the trimmed portion as if the image was recomposed. Set the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again before printing. 1 On the print settings screen, select [Trimming]. 2 Set the trimming frame size, position, and aspect ratio. The image area within the trimming frame will be printed.
wPrinting Depending on the printer, the trimmed image area may not be printed as you specified. The smaller you make the trimming frame, the grainier the picture will look in the print. While trimming the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the trimming frame may not be displayed accurately. Handling Printer Errors If you resolve a printer error (no ink, no paper, etc.
W Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options 1 Select [Print order]. Under the [31] tab, select [Print order], then press <0>. [Set up]. 2 Select Select [Set up], then press <0>. as desired. 3 SetSetthetheoption [Print type], [Date], and [File No.]. Select the option to be set, then press <0>.
W Digital Print Order Format (DPOF) Print type Date File number K L K L Standard Prints one image on one sheet. Index Multiple thumbnail images are printed on one sheet. Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date on the print. [On] imprints the file number on the print. 4 Exit the setting. Press the button. X The print order screen will reappear. Next, select [Sel.Image], [Byn], or [All image] to order the images to be printed.
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6> dial clockwise. Press the button to save the print order to the card. Quantity Total images selected Checkmark Index icon [Standard] [Both] Press <0> and a print order for one copy of the displayed image will be placed.
W Direct Printing with DPOF With a PictBridge printer, you can easily print images with DPOF. 1 Prepare to print. See page 296. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [31] tab, select [Print order]. 3 Select [Print]. [Print] will be displayed only if the camera is connected to a printer and printing is possible. 4 Set the [Paper settings] (p.298). Set the printing effects (p.300) if necessary. 5 Select [OK]. Before printing, be sure to set the paper size.
d Transferring Images to a Personal Computer You can connect the camera to a personal computer and operate the camera to transfer images on the card to the personal computer. This is called direct image transfer. The direct image transfer can be performed with the camera while you look at the LCD monitor. The images transferred to the personal computer will be saved in the [Pictures] or [My Pictures] folder and organized in folders by shooting date.
d Transferring Images to a Personal Computer the camera’s power switch to 3 Set <1>. When the personal computer displays a screen to select the program, select [EOS Utility]. X The EOS Utility screen will appear on the personal computer. After the EOS Utility screen appears, do not operate EOS Utility. If any screen other than EOS Utility’s top screen is displayed, [Direct transfer] in step 5 on page 312 will not be displayed. (The image transfer function will not be available.
d Transferring Images to a Personal Computer 3 Select the Images to be Transferred Sel.Image 1 Select [Image transfer]. Under the [32] tab, select [Image transfer], then press <0>. [Image sel./transfer]. 2 Select Select [Image sel./transfer], then press <0>. [Sel.Image]. 3 Select Select [Sel.Image], then press <0>. the images to be 4 Select transferred. Turn the <5> dial to select the image to be transferred, then press <0>.
d Transferring Images to a Personal Computer the image. 5 Transfer On the computer screen, check that EOS Utility’s top screen is displayed. Select [Direct transfer], then press <0>. On the confirmation screen, select [OK] and the images will be transferred to the personal computer. Images selected with [Sel.n] and [All image] can also be transferred in this way. Sel.n Select [Sel.n] and select [Folder images not transfer’d].
Customizing the Camera You can customize various camera features to suit your picture-taking preferences with Custom Functions. Also, the current camera settings can be saved under the Mode Dial’s , , and positions. The features explained in this chapter can be set and used in the following shooting modes: d/s/f/a/ F.
3 Custom FunctionsN A LV Shooting 81: Exposure Exposure level increments ISO speed setting increments p.315 Bracketing auto cancel Bracketing sequence Number of bracketed shots Safety shift p.316 p.317 k Movie Shooting k k k In a k (Still photo, with WB bracketing set) k k k 82: Display/Operation Warnings z in viewfinder LV shooting area display p.318 Dial direction during Tv/Av Multi function lock p.
3 Custom Function SettingsN Under the [8] tab, you can customize various camera features to suit your picture-taking preferences. Any settings different from the default will be displayed in blue. C.Fn1: Exposure Exposure level increments 1/3: 1/3-stop 1/2: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. Effective when you prefer to control the exposure in less fine increments than 1/3-stop increments.
3 Custom Function SettingsN Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed.
3 Custom Function SettingsN Safety shift OFF: Disable Tv/Av: Shutter speed/Aperture This takes effect in the shutter-priority AE (s) and aperture-priority AE (f) modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure. ISO: ISO speed This works in the Program AE (d), shutter-priority AE (s), and aperture-priority AE (f) modes.
3 Custom Function SettingsN C.Fn2: Disp./Operation Warnings z in viewfinder When any of the following functions are set, the icon can be displayed on the viewfinder’s bottom right (p.23). Select the function for which you want the warning icon to appear, press <0> to append a , then select [OK]. When monochrome V is set If the Picture Style is set to [Monochrome] (p.131), the warning icon will appear. When WB is corrected If white balance correction (p.140) is set, the warning icon will appear.
3 Custom Function SettingsN Dial direction during Tv/Av Normal Reverse direction The dial’s turning direction for setting the shutter speed and aperture can be reversed. In the shooting mode, the turning direction of the <6> and <5> dial will be reversed. In the other shooting modes, the turning direction of only the <6> dial will be reversed. The <5> dial’s turning direction will be the same for the mode and for setting the exposure compensation.
3 Custom Function SettingsN C.Fn3: Others Add cropping information If you set cropping information, vertical lines for the aspect ratio you have set will appear on the Live View image. You can then compose the shot as if you were shooting with a medium- or large-format camera (6x6 cm, 4x5 inch, etc.). When you take a picture, the aspect ratio information for cropping the image with the provided software will be appended to the image. (The image is recorded to the card without being cropped.
82: Custom Controls You can assign frequently-used functions to camera buttons or dials according to your preferences. 1 Select [82: Custom Controls]. Under the [82] tab, select [Custom Controls], then press <0>. X The Custom Controls screen will appear. a camera button or dial. 2 Select Turn the <5> dial to select a button or dial, then press <0>. X The name of the camera control and the assignable functions will be displayed. a function.
82: Custom Controls Assignable Functions to Camera Controls Function Page k*1 k*1 k k k k AE lock (hold) k k FE lock k k k k Metering and AF start 324 k AF stop AF Switch to registered AF function 325 ONE SHOT z AI SERVO Switch to registered AF point 326 AF point direct selection k Metering start AE lock 326 AE lock (while button pressed) Exposure Set ISO speed (hold button, turn Set ISO speed ( k ) during metering) 327 Shutter speed setting in M mode Aperture setting in M
82: Custom Controls * k k k k*2 k*2 k k k*3 k*3 k k k k k k k k k*4 k k k k*5 k*5 k* k*5 5 k k k k k k k k k k k k k k k * The AF stop button ( k k ) is provided only on super telephoto IS lenses.
82: Custom Controls : Metering and AF start When you press the button assigned to this function, metering and AF are executed. *1: If you assign the [Metering and AF start] function to the
and buttons and add the function to switch to the registered AF point, you can instantly switch to the registered AF point. To enable this function, press the button in step 3 on page 321. On the [AF start point] selection screen, select [Registered AF point]. Registering and using an AF point 1.
82: Custom Controls : AF stop The AF will stop while you hold down the button assigned to this function. Convenient when you want to lock the focus during AI Servo AF. : Switch to registered AF function After setting AF area selection mode (p.72), Tracking sensitivity (p.90), Acceleration/deceleration tracking (p.91), AF point auto switching (p.92), AI Servo 1st image priority (p.94), and AI Servo 2nd image priority (p.
82: Custom Controls : Switch to registered AF point During metering, when you press the button assigned to this function, the camera will switch to the AF point registered on page 324. *3: In step 3 on page 321, when you press the button, you can select [Switch only when btn is held] or [Switch each time btn is pressed]. : AF point direct selection During metering, you can select an AF point directly with the <5> dial or <9> without pressing the button.
82: Custom Controls : FE lock During flash photography, pressing the button assigned to this function will fire a preflash and record the required flash output (FE lock). : Set ISO speed (hold button, turn ) You can set the ISO speed by holding down <0> and turning the <6> dial. If Auto ISO is set, manual ISO speed setting will take effect. Auto ISO cannot be set.
82: Custom Controls : One-touch image quality setting When you press the button assigned to this function, you can switch to the image-recording quality set here. While the camera switches the image-recording quality, the image-recording quality will blink on the LCD panel. After the shooting ends, the One-touch image quality setting will be canceled and the camera will switch back to the previous imagerecording quality.
82: Custom Controls : Depth-of-field preview When you press the depth-of-field preview button, the aperture will stop down and you can check the depth of field (p.165). : IS start With the lens’ IS switch set to <1>, the lens’ Image Stabilizer operates when you press the button assigned to this function. : VF electronic level When you press the button assigned to this function, the viewfinder will display a grid and an electronic level using the AF points.
82: Custom Controls : Menu display Pressing <0> will display the menu on the LCD monitor. : Image playback Pressing <0> will play back images. : Magnify/Reduce (press SET, turn ) Press <0> to magnify the images recorded on the card. See p.251 for the operation procedure. You can also magnify the Live View image during Live View shooting and movie shooting when focusing with Live Mode, Quick Mode, and manual focus (p.210, 214).
3 Registering My MenuN Under the My Menu tab, you can register up to six menu options and Custom Functions whose settings you change frequently. 1 Select [My Menu settings]. Under the [9] tab, select [My Menu settings], then press <0>. [Register to My Menu]. 2 Select Select [Register to My Menu], then press <0>. the desired items. 3 Register Select an item to register, then press <0>. On the confirmation dialog, select [OK] and press <0> to register the item. You can register up to six items.
w Register Custom Shooting ModesN You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial’s , , and positions. 1 Select [Custom shooting mode (C1-C3)]. Under the [54] tab, select [Custom shooting mode (C1-C3)], then press <0>. [Register settings]. 2 Select Turn the <5> dial to select [Register settings], then press <0>. the Custom shooting mode.
w Register Custom Shooting ModesN Settings Registered Shooting functions Shooting mode + exposure setting, ISO speed, AF mode, AF area selection mode, AF point, Metering mode, Drive mode, Exposure compensation amount, Flash exposure compensation amount Menu functions [z1] Image quality, Image review, Beep, Release shutter without card, Lens aberration correction (Peripheral illumination correction, Chromatic aberration correction), External Speedlite control, Mirror lockup [z2] Exposure compensation/AEB, I
w Register Custom Shooting ModesN [x2] Slide show, Image jump with 6 [x3] Highlight alert, AF point disp., Playback grid, Histogram display, Movie play count, Magnificatn (approx.
Reference This chapter provides reference information for camera features, system accessories, etc.
B Button Functions When you press the button while the camera is ready to shoot, you can display [Displays camera settings], [Electronic level] (p.60), and [Displays shooting functions] (p.337). Under the [53] tab, [z button display options] enables you to select the options displayed when the button is pressed. Select the desired display option and press <0> to append a checkmark . After making the selection, select [OK], then press <0>.
B Button Functions Shooting Settings White balance correction Shutter speed Shooting mode Exposure level indicator Aperture AE lock Flash exposure compensation ISO speed Highlight tone priority Custom Controls Picture Style AF mode Quick Control icon Battery check White balance Eye-Fi card transmission status Metering mode Flash-ready/FE lock/ High-speed sync Drive mode Image-recording quality Possible shots Remaining number of exposures (multiple exposures) Card indicator Card selection icon Multiple e
3 Checking the Battery Information You can check the battery’s condition on the LCD monitor. Each Battery Pack LP-E6 has a unique serial number, and you can register multiple battery packs to the camera. When you use this feature, you can check the registered battery pack’s remaining capacity and operation history. Select [Battery info.]. Under the [53] tab, select [Battery info.], then press <0>. X The battery info screen will appear. Battery position Battery model or household power source being used.
3 Checking the Battery Information Registering the Battery to the Camera You can register up to six LP-E6 battery packs to the camera. To register multiple battery packs to the camera, do the procedure below for each battery pack. 1 Press the button. With the battery info. screen displayed, press the button. X The battery history screen will appear. X If the battery has not been registered, it will be grayed out. [Register]. 2 Select Select [Register], then press <0>.
3 Checking the Battery Information Labeling the Serial No. on the Battery Affixing a serial number label onto all the registered Battery Pack LPE6’s makes it convenient. 1 Serial No. Write the serial number on a label. Write the serial number displayed on the battery history screen on a commercially-available label approx. 25 mm x 15 mm / 1.0 in. x 0.6 in. in size. 7c40 0300 out the battery and affix the 2 Take label. Set the power switch to <2>.
3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery Pack You can check the remaining capacity of any battery pack (even when not installed) and also when it was last used. Serial No. Date last used Look for the serial number. Refer to the battery’s serial number label and look for the battery’s serial number on the battery history screen. X You can check the respective battery pack’s remaining capacity and the date when it was last used.
Using a Household Power Outlet With the AC Adapter Kit ACK-E6 (sold separately), you can connect the camera to a household power outlet and not worry about the remaining battery level. 1 Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the AC Adapter’s socket. the power cord. 2 Connect Connect the power cord as shown in the illustration. After using the camera, unplug the power plug from the power outlet. the cord in the groove.
Replacing the Date/Time Battery The date/time (backup) battery maintains the camera’s date and time. Its service life is approx. 5 years. If the date/time is reset when camera is turned on, follow the procedure below to replace the backup battery with a new CR1616 lithium battery. The date/time/zone setting will also be reset, so be sure to set the correct date/time/zone (p.36). 1 Set the power switch to <2>. the battery holder 2 Unscrew screw. Use a small Phillips screwdriver.
Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a personal computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card’s manufacturer.
Using Eye-Fi Cards the [Access point SSID:]. 5 Check Check that an access point is displayed for [Access point SSID:]. You can also check the Eye-Fi card’s MAC address and firmware version. Press the button to exit the menu. the picture. 6 Take X The picture is transferred and the Transmission status icon H (Gray) Not connected : H (Blinking) Connecting : H (Displayed) Connected : H ( ) Transferring : icon switches from gray (Not connected) to one of the icons below.
Function Availability Table According to Shooting Mode o: Set automatically k: User selectable Function All image quality settings selectable ISO speed Automatically set/Auto ISO A k k k k k k o k k k k k Manual Picture Style F k k k k k Automatic selection Movies k z*1 k o Except a kIn a kIn a A mode: D D Manual selection k k k k k k k k k k k k Preset k k k k k k Custom k k k k k k Color temperature setting k k k k k k Correction/Bracketing k k k k k Auto White balance : No
Function Availability Table According to Shooting Mode Function AF point selection AF A Auto o Manual o k k k k k Manual focusing (MF) k k k k k k k k k k k o External Speedlite k k k k k Program shift k AE lock*3 k k k Exposure compensation k k k AEB k k k k With f (except A) In d, s, f, F k k k k k Single shooting k k k k k k k High-speed continuous shooting k k k k k k k Low-speed continuous shooting k k k k k k k Silent single shooting k k k k k k k Silent contin
Menu Settings For Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Image quality Page 1 / 41 / 61 73 / 83 / 74 / 84 / 7a / 8a / b / c 119 Image review Off / 2 sec. / 4 sec. / 8 sec. / Hold Beep Enable / Disable 55 - Release shutter without card Enable / Disable 32 Lens aberration correction Peripheral illumination: Enable / Disable Chromatic aberration: Enable / Disable 147 External Speedlite control Flash firing / E-TTL II metering / Flash sync.
Menu Settings z: Shooting 2 (Red) Page Exposure compensation/AEB 1/3-stop increments, ±5 stops (AEB ±3 stops) 169 170 ISO speed settings ISO speed / ISO speed range / Auto ISO range / Minimum shutter speed 124 to 128 Auto Lighting Optimizer White balance Disable / Low / Standard / High Disable during manual exposure Q/W/E/R/Y/U/D/O/P (Approx.
Menu Settings z: Shooting 4* (Red) Page Live View shooting Enable / Disable 203 AF mode Live mode / u Live mode / Quick mode 207 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 203 Aspect ratio 3:2 / 4:3 / 16:9 / 1:1 204 Exposure simulation Enable / During e / Disable 205 Silent LV shooting Mode 1 / Mode 2 / Disable 206 Metering timer 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 30 min. 206 * In the mode, these menu options are displayed under [z2].
Menu Settings 2: AF3 (Purple) Page Enable after One-Shot AF / Disable after OneUSM lens electronic MF Shot AF / Disable in AF mode 96 AF-assist beam firing Enable / Disable / IR AF assist beam only 97 One-Shot AF release priority Release priority / Focus priority 97 Lens drive when AF impossible Continue focus search / Stop focus search 98 Selectable AF point 61 points / Only cross-type AF points / 15 points / 9 points 98 Select AF area selection mode Manual selection: Spot AF / Manual sel
Menu Settings 3: Playback 1 (Blue) Page Protect images Erase-protect images 272 Rotate image Rotate vertical images 254 Erase images Erase images 277 Print order Specify images to be printed (DPOF) 305 Image copy Copy images between cards 274 RAW image processing Process 1 images 282 3: Playback 2 (Blue) Resize Downsize the image’s pixel count 287 Rating [OFF] / l / m / n / o / p 255 Slide show Playback description, Display time, and Repeat for auto playback 265 Image transfer
Menu Settings 5: Set-up 1 (Yellow) Page Record function+card/ folder selection [Record func.
Menu Settings 5: Set-up 3 (Yellow) Page Video system NTSC / PAL 231 271 Battery info.
Menu Settings For Movie Shooting z: Shooting 4*1 (Movie) (Red) Page AF mode Live mode / u Live mode / Quick mode 239 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 239 Movie recording size 1920x1080 (6 / 5 / 4) (W / X) 1280x720 (8 / 7) (W / X) 640x480 (6 / 5) (X) 231 Sound recording: Auto / Manual / Disable Sound recording*2 Recording level 234 Wind filter: Disable / Enable Silent LV shooting Mode 1 / Mode 2 / Disable 240 Metering timer 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min.
System Map ST-E2 ST-E3-RT 270EX II Dioptric Adjustment Lenses Eg 320EX 430EX II 600EX-RT/ Macro Ring Lite Macro Twin Lite MR-14EX MT-24EX 600EX Bundled Accessories Anti-Fog Eyepiece Eg Eyecup Eg Wide Strap EW-EOS5DMKIII Angle Finder C Battery Pack LP-E6 Date / time CR1616 Battery Charger lithium battery LC-E6 or LC-E6E Hand Strap E2 Battery Grip BG-E11 AC Adapter DC Coupler Battery Magazine AC-E6 DR-E6 BGM-E11L for two AC Adapter Kit LP-E6 battery packs ACK-E6 (attached to BG-E11) 356 Car Batter
System Map GPS Receiver Headphones Remote Controller GP-E2 RC-6 Timer Remote Remote Switch Controller RS-80N3 TC-80N3 Wireless Controller LC-5 External microphone EF lenses HDMI Cable HTC-100 (2.9 m/9.5 ft.) Stereo AV Cable AVC-DC400ST (1.3 m/4.3 ft.) Wireless File Transmitter WFT-E7 TV/Video EOS DIGITAL Software Instruction Solution Disk Manual Interface Cable IFC-200U (1.9 m/6.2 ft.) Wireless LAN access point Wireless LAN adapter Interface Cable IFC-500U (4.7 m/15.4 ft.
Troubleshooting Guide If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power-Related Problems The battery pack does not recharge. If the battery’s remaining capacity (p.338) is 94% or higher, the battery will not be recharged. Do not recharge any battery pack other than genuine Canon Battery Pack LP-E6. The charger’s lamp blinks at high speed.
Troubleshooting Guide The access lamp still blinks even when the power switch is set to <2>. If the power is turned off while an image is being recorded to the card, the access lamp will remain on/continue to blink for a few seconds. When the image recording is completed, the power will turn off automatically. The battery becomes exhausted quickly. Use a fully-charged battery pack (p.28). The battery performance may have degraded. See [53: Battery info.
Troubleshooting Guide Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-S lenses (p.39). The viewfinder is dark. Install a recharged battery pack in the camera (p.28). No images can be shot or recorded. The card is not properly inserted (p.31). If you are using an SD card, slide the card’s write-protect switch to the Write/Erase setting (p.31). If the card is full, replace the card or delete unnecessary images to make room (p.31, 277).
Troubleshooting Guide The image is out of focus. Set the lens focus mode switch to (p.39). To prevent camera shake, press the shutter button gently (p.43, 44). If the lens has an Image Stabilizer, set the IS switch to <1> (p.42). In low light, the shutter speed may become slow. Use a faster shutter speed (p.162), set a higher ISO speed (p.124), use flash (p.188), or use a tripod. There are fewer AF points. Depending on the attached lens, the number of usable AF points and patterns will differ.
Troubleshooting Guide The maximum burst during continuous shooting is lower. If you shoot something that has fine detail (such as a field of grass), the file size will be larger and the actual maximum burst may be lower than the number mentioned on page 121. ISO 100 cannot be set. ISO speed expansion cannot be selected. If [z3: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200-25600 (or up to 12800 for movie shooting).
Troubleshooting Guide When I use the mode with flash, the shutter speed becomes slow. If you shoot at night when the background is dark, the shutter speed becomes slow automatically (slow-sync shooting) so that both the subject and background are properly exposed. To prevent a slow shutter speed, under [z1: External Speedlite control], set [Flash sync. speed in Av mode] to [1/200-1/60 sec. auto] or [1/200 sec. (fixed)] (p.192). The flash does not fire.
Troubleshooting Guide During Live View and movie shooting, a white icon is displayed. or red E It indicates that the camera’s internal temperature is high. If the white < > icon displayed, the still photo’s image quality may deteriorate. If the red icon is displayed, it indicates that the Live View or movie shooting will soon be terminated automatically (p.215, 241). Movie shooting terminates by itself. If the card’s writing speed is slow, movie shooting may stop automatically.
Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie when [Maximum: 25600] is set with [ISO speed range] and ISO speed is set to ISO 16000/20000/25600, the ISO speed will switch to ISO12800 (during movie shooting with manual exposure). Even if you switch back to still photo shooting, the ISO speed will not revert to the original setting. If you shoot a movie when 1. L (50) or 2. H1 (51200)/H2 (102400) is set, the ISO speed setting will switch to 1.
Troubleshooting Guide When I shoot still photos during movie shooting, the movie shooting stops. To shoot still photos during movie shooting, using a CF card compatible with UDMA transfer rates is recommended. Setting a lower image quality for still photos and shooting fewer continuous still photos can also resolve the problem. Time code is off. Shooting still photos during movie shooting will cause a discrepancy between the actual time and time code.
Troubleshooting Guide The fourth character in the file name changes. With [51: File name], select the camera’s unique file name or the file name registered under User setting 1 (p.152). The file numbering does not start from 0001. If the card already contains recorded images, the image number may not start from 0001 (p.154). The shooting date and time displayed is incorrect. The correct date and time has not been set (p.36). Check the time zone and daylight savings time (p.37).
Troubleshooting Guide [Eye-Fi settings] does not appear. [Eye-Fi settings] will appear only when an Eye-Fi card is inserted into the camera. If the Eye-Fi card has a write-protect switch set to the LOCK position, you will not be able to check the card’s connection status or disable Eye-Fi card transmission (p.344). Playback Problems Part of the image blinks in black. [33: Highlight alert] is set to [Enable] (p.247). A red box is displayed on the image. [33: AF point disp.] is set to [Enable] (p.247).
Troubleshooting Guide No image appears on the TV screen. Use the stereo AV cable that came with the camera (p.271). Make sure the stereo AV cable or HDMI cable’s plug is inserted all the way in (p.268, 271). Set the video OUT system (NTSC/PAL) to the same video system as the TV set (p.271). There are multiple movie files for a single movie shoot. If the movie file size reaches 4 GB, another movie file will be created automatically (p.232). My card reader does not recognize the card.
Troubleshooting Guide Sensor Cleaning Problems The shutter makes a noise during sensor cleaning. If you selected [Clean nowf], the shutter will make a noise, but no picture is taken (p.290). Automatic sensor cleaning does not work. If you repeatedly turn the power switch <1> and <2> at a short interval, the icon may not be displayed (p.34). Printing-Related Problems There are fewer printing effects than listed in the instruction manual.
Error Codes Error number If there is a problem with the camera, an error message will appear. Follow the onscreen instructions. Countermeasures No. 01 02 Error Message & Solution Communications between the camera and lens is faulty. Clean the lens contacts. Î Clean the electrical contacts on the camera and lens or use a Canon lens (p.15, 18). Card * cannot be accessed. Reinsert/change card * or format card * with camera. Î Remove and insert the card again, replace the card, or format the card (p.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera CF card (Type I, UDMA mode 7-compatible), SD memory card, SDHC memory card, SDXC memory card Approx. 36 x 24 mm Canon EF lenses (except EF-S lenses) (35 mm-equivalent lens focal length will be as indicated on the lens) Canon EF mount • Image Sensor Type: Effective pixels: Aspect ratio: Dust delete feature: CMOS sensor Approx. 22.
Specifications Noise reduction: Automatic image brightness correction: Highlight tone priority: Lens aberration correction: Applicable to long exposures and high ISO speed shots Auto Lighting Optimizer Provided Peripheral illumination correction, Chromatic aberration correction • Viewfinder Type: Coverage: Eye-level pentaprism Vertical/Horizontal approx. 100% (with Eye point approx. 21 mm) Magnification: Approx. 0.71x (-1 m-1 with 50 mm lens at infinity) Eye point: Approx.
Specifications AF fine adjustment: AF-assist beam: AF Microadjustment (All lenses by same amount or Adjust by lens) Emitted by the EOS-dedicated external Speedlite • Exposure Control Metering modes: 63-zone TTL full-aperture metering Evaluative metering (linked to all AF points) Partial metering (approx. 6.2% of viewfinder at center) Spot metering (approx. 1.5% of viewfinder at center) Center-weighted average metering Metering range: EV 1 - 20 (at 23°C/73°F with EF50mm f/1.
Specifications • Shutter Type: Shutter speeds: Electronically-controlled, focal-plane shutter 1/8000 sec. to 30 sec., bulb (Total shutter speed range. Available range varies by shooting mode.), X-sync at 1/200 sec. • Drive System Drive modes: Continuous shooting speed: Max. burst: Single shooting, High-speed continuous shooting, Lowspeed continuous shooting, Silent single shooting, Silent continuous shooting, 10-sec. self-timer/remote control, 2sec.
Specifications • Live View Shooting Aspect ratio settings: Focus modes: 3:2, 4:3, 16:9, 1:1 Live mode, Face detection Live mode (contrast detection), Quick mode (phase-difference detection), Manual focusing (Approx. 5x / 10x magnification possible) Focusing brightness range: EV 1 - 18 (with contrast detection, at 23°C/73°F, ISO 100) Metering modes: Evaluative metering with the image sensor Metering range: EV 0 - 20 (at 23°C/73°F with EF50mm f/1.
Specifications Metering range: Exposure control: EV 0 - 20 (at 23°C/73°F with EF50mm f/1.4 USM lens, ISO 100) 1. Autoexposure, 2. Shutter-priority AE, 3. Aperturepriority AE, 4. Manual exposure * With 1, 2, and 3, exposure compensation and AE lock are possible (except in Scene Intelligent Auto mode).
Specifications Image rotate: Ratings: Movie playback: Slide show: Image protect: Copying images: Possible Provided Enabled (LCD monitor, video/audio OUT, HDMI OUT), built-in speaker All images, by date, by folder, movies, stills, or by rating Possible Possible • Post-Processing of Images In-camera RAW image Brightness correction, White balance, Picture Style, Auto Lighting processing: Optimizer, High ISO speed noise reduction, JPEG imagerecording quality, Color space, Peripheral illumination correction,
Specifications Wireless remote control: Remote Controller RC-6 Eye-Fi card: Compatible • Power Battery: Battery information: Battery life: (Based on CIPA testing standards) Movie shooting time: Date/Time battery: Battery Pack LP-E6 (Quantity 1) * AC power can be supplied via AC Adapter Kit ACK-E6. * With Battery Grip BG-E11 attached, size-AA/LR6 batteries can be used. Remaining capacity, Shutter count, Recharge performance, and Battery registration possible With viewfinder shooting: Approx.
Specifications • Battery Charger LC-E6 Compatible battery: Battery Pack LP-E6 Recharging time: Approx. 2 hr. 30 min. Rated input: 100 - 240 V AC (50/60 Hz) Rated output: 8.4 V DC / 1.2 A Working temperature range: 5°C - 40°C / 41°F - 104°F Working humidity: 85% or less Dimensions (W x H x D):Approx. 69.0 x 33.0 x 93.0 mm / 2.7 x 1.3 x 3.7 in. Weight: Approx. 130 g / 4.6 oz.
Specifications All the data above is based on Canon’s testing standards and CIPA (Camera & Imaging Products Association) testing standards and guidelines. Dimensions, maximum diameter, length and weight listed above are based on CIPA Guidelines (except weight for camera body only). Product specifications and the exterior are subject to change without notice. If a problem occurs with a non-Canon lens attached to the camera, consult the respective lens maker.
Use of genuine Canon accessories is recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of nongenuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
Digital Camera Model DS126321 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS — This manual contains important safety and operating instructions for Battery Charger LC-E6 & LC-E6E. 2. Before using the charger, read all instructions and cautionary remarks on (1) the charger, (2) the battery pack, and (3) the product using the battery pack. 3. CAUTION — To reduce risk of injury, charge only the Battery Pack LP-E6. Other types of batteries may burst, causing personal injury and other damage. 4.
MEMO 387
MEMO 388
MEMO 389
MEMO 390
MEMO 391
MEMO 392
Software Start Guide This chapter gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM) provided with the camera and explains how to install the software on a personal computer. It also explains how to view the PDF files in the Software Instruction Manual CD-ROM.
Software Start Guide EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a personal computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use the personal computer to set various camera settings and shoot remotely with the computer connected to the camera. Digital Photo Professional This software is recommended for users who mainly shoot RAW images.
Software Start Guide Installing the Software Do not connect the camera to your computer before you install the software. The software will not be installed correctly. Even if a previous version of the software is installed, install the software by following the steps below. (The newer version will overwrite the previous version.) 1 Insert EOS DIGITAL Solution Disk (CD-ROM). For Macintosh, double-click to open the CD-ROM icon displayed on the desktop, then double-click on [Canon EOS Digital Installer].
Software Start Guide Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Instruction Manual PDFs 1 Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. 2 Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. 3 Copy the [English] folder to your computer. Instruction Manual PDFs with the names below are copied.
Index 10-sec. or 2-sec. delay..................113 1280x720 ......................................231 1920x1080 ....................................231 4- or 9-image index display...........249 61-point automatic selection AF ..............................73, 77 640x480 ........................................231 A ALL-I (I-only)................................. 231 Ambient light sensor....................... 20 Aperture-priority AE.............. 164, 220 Area AF frame ....................
Index Camera shake ..........................42, 43 Card ....................................15, 31, 53 Card reminder ............................32 Format ........................................53 Low-level format .........................54 Problem ................................33, 54 Center-weighted average metering........................................168 CF card 9 Card Charger.....................................26, 28 Chromatic aberration correction ...148 Cleaning...............................
Index First-curtain synchronization .........194 Headphones ................................. 235 Flash (Speedlite) Custom Functions.....................196 External Speedlite.....................188 FE lock......................................188 Flash control .............................191 Flash exposure compensation..188 Flash-sync speed .....................189 Manual flash .............................193 Shutter synchronization (1st/2nd curtain)........................194 Wireless...............
Index Image-recording quality ................119 Index display.................................249 INFO. button .........200, 225, 244, 336 IPB ................................................231 ISO speed.....................124, 221, 224 Automatic setting (Auto) ...........125 Automatic setting range............127 ISO expansion..........................126 Manual Setting range ...............126 Minimum shutter speed ............128 Setting increments....................315 J JPEG ....................
Index Metering timer .......................206, 240 M-RAW (Medium RAW) ....... 119, 122 MF (Manual focusing) ...........111, 214 Multi function .................. 73, 188, 323 M-Fn........................................73, 323 Multi-controller................................ 47 Microadjustment............................104 Multi-function lock........................... 47 Microphone ...........................218, 235 Multiple exposures ....................... 177 Mirror lockup ...............
Index Power Auto power off ............................55 Battery check......................35, 338 Battery info ...............................338 Household power .....................342 Possible shots ............35, 121, 199 Recharge....................................28 Recharge performance.............338 Pressing completely........................44 Pressing halfway.............................44 Printing..........................................295 Layout.......................................
Index Silent shooting Continuous shooting.................112 Silent LV shooting.............206, 240 Single shooting .........................112 Single image display .....................244 Single shooting .............................112 Single-point AF .........................72, 75 Single-point Spot AF .................72, 75 Slide show.....................................265 Small (Image-recording quality) ..................................121, 287 Software........................................
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.
This quick guide explains basic function settings and how to shoot and play back images. You can take this guide with you for shooting. For detailed instructions, refer to the EOS 5D Mark III Instruction Manual. E English Edition CPQ-E002-000 © CANON INC.
Quick Start Guide 1 2 Insert the battery. Insert a card.* The camera-front side slot is for a CF card, and the camera-back side slot is for an SD card. 3 Attach the lens. 4 Set the lens focus mode switch to . 5 Set the power switch to <1>. Align it with the red dot. * Shooting is possible with either a CF card or an SD card in the camera.
6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto). 7 Focus the subject. Aim the viewfinder center over the subject and press the shutter button halfway to autofocus. 8 Take the picture. 9 View the image. Press the shutter button completely to take the picture. The captured image will be displayed for 2 sec. on the LCD monitor. The M on the right of the function indicates that the function is available only when the Mode Dial is set to d,s,f,a, or F.
Image Playback 6 Index 0 Magnify 6 u x Playback L Erase 9 56 Select image BShooting information
Preparation Menu Operations button LCD monitor <6> Main Dial button <0> button <5> Quick Control Dial 1. Press the button to display the menu. 2. Each time you press the button, the main tab will switch. 3. Turn the <6> dial to select a secondary tab, then turn the <5> dial to select the desired item. 4. Press <0> to display the setting. 5. Turn the <5> dial to set the item, then press <0>.
Image-recording Quality Select [z1: Image quality], then press <0>. Turn the <6> or <5> dial to select the image-recording quality, then press <0>. Image-recording quality Pixels Possible shots RAW: Turn the <6> dial to select the quality. JPEG: Turn the <5> dial to select the quality. A Picture StyleN Press the button. Select [A], then press <0>. Turn the <5> dial to select the Picture Style, then press <0>. Style Description Color tones optimized for the particular scene.
Q Quick Control Press the button. The Quick Control screen will appear. White balance correction Aperture Highlight tone priority ISO speed Shutter speed Shooting mode Exposure compensation/ AEB setting Flash exposure compensation Custom Controls Picture Style Image-recording quality AF mode White balance Metering mode Drive mode Recording function/ Card selection Auto Lighting Optimizer Tilt the <9> to select the function, then turn the <6> or <5> dial to set it.
Custom Functions 81: Exposure Exposure level increments ISO speed setting increments Bracketing auto cancel Bracketing sequence Number of bracketed shots Safety shift 82: Display/Operation Warnings z in viewfinder LV shooting area display Dial direction during Tv/Av Multi function lock Custom Controls 83: Others Add cropping information Default Erase option 84: Clear Clear all Custom Func. (C.
Shooting Operation Nomenclature ISO speed setting/ Flash exposure compensation button AF area selection mode/ Multi-function button AF mode selection/ Drive mode selection button Metering mode selection/ White balance selection button Mode Dial lock release button Mode Dial <6> Main Dial Shutter button Live View shooting/ Movie shooting switch <0> Start/Stop button Focus mode switch AF start button AE lock button AF point selection button Power switch <9> Multi-contro
LCD Panel Monochrome shooting Aperture Possible shots ISO speed Shutter speed AEB AF mode White balance Drive mode Metering mode Exposure level indicator Image-recording quality Battery check Flash exposure compensation OK NG Viewfinder Information Grid ([52] tab) Area AF frame AE lock Battery check Flash-ready Flash exposure compensation Shutter speed Aperture Focus confirmation light AF status indicator Maximum burst ISO speed Exposure level indicator
A Mode All the settings necessary for shooting are set automatically. You just press the shutter button, and the camera does the rest. Scene Intelligent Auto Aim the center of the Area AF frame over the subject. Press the shutter button halfway to focus. Check the display. Compose the shot and press the shutter button completely. d/s/f/a Modes You can change the camera settings as desired to shoot in various ways. * Set the switch to the left (Multi function lock released).
s: Shutter-priority AE Set the Mode Dial to . Turn the <6> dial to set the desired shutter speed, then focus the subject. The aperture will be set automatically. If the aperture display blinks, turn the <6> dial until it stops blinking. f: Aperture-priority AE Set the Mode Dial to . Turn the <6> dial to set the desired aperture, then focus the subject. The shutter speed will be set automatically. If the shutter speed display blinks, turn the <6> dial until it stops blinking.
i: ISO SpeedN Press the button, then turn the <6> dial. ISO 100 to 25600 can be set in 1/3-stop increments. When “A” is selected, the ISO speed is set automatically. When you press the shutter button halfway, the ISO speed setting is displayed. i Drive Mode Press the button, then turn the <5> dial. u: Single shooting o: High-speed continuous shooting i: Low-speed continuous shooting B: Silent single shooting M: Silent continuous shooting Q: 10-sec. self-timer/ Remote control k: 2-sec.
f: AF ModeN Set the lens focus mode switch to . Press the button, then turn the <6> dial. X(One-Shot AF): For still subjects 9(AI Focus AF): Switches the AF mode automatically Z(AI Servo AF): For moving subjects S AF Point SelectionN Press the button, then look through the viewfinder. The AF point selection will change in the direction you tilt the <9>. If you press <9> straight down, the center AF point (or center Zone) will be selected.
AF Area Selection Mode Press the button. Look through the viewfinder and press the button. Each time you press the button, the AF area selection mode changes. A Live View Shooting Set the switch to . Press the <0> button and the Live View image will appear on the LCD monitor. Press the shutter button halfway to focus, then press it completely to take the picture. Press the <0> button to stop the Live View shooting.
k Shooting Movies Set the switch to . The image will appear on the LCD monitor. Press the shutter button halfway to focus. Press the <0> button to start shooting a movie. To stop movie shooting, press the <0> button again. To shoot still photos, press the shutter button completely.
() PP I / ,6 860 (1* Instructions
7KDQN \RX IRU SXUFKDVLQJ D &DQRQ SURGXFW &DQRQ¶V () PP I / ,6 860 LV D KLJK SHUIRUPDQFH VWDQGDUG ]RRP OHQV IRU XVH ZLWK (26 FDPHUDV 7KH OHQV LV LQVWDOOHG ZLWK DQ ,PDJH 6WDELOL]HU DQG DOORZV IRU FORVH XS VKRRWLQJ XS WR D PDJQL¿FDWLRQ RI [ ZKHQ WKH ]RRP ULQJ LV VHW WR PDFUR ● ³,6´ VWDQGV IRU ,PDJH 6WDELOL]HU ● ³860´ VWDQGV IRU 8OWUDVRQLF 0RWRU )HDWXUHV 7KH ,PDJH 6WDELOL]HU SURYLGHV WKH HIIHFW RI KDYLQJ D VKXWWHU VSHHG DERXW IRXU VWRSV IDVWHU GXULQJ QRUPDO VKRRWLQJ 7KLV IXQFWLRQ
6DIHW\ 3UHFDXWLRQV +DQGOLQJ &DXWLRQV ● ,I WKH OHQV LV WDNHQ IURP D FROG HQYLURQPHQW LQWR D ZDUP RQH FRQGHQVDWLRQ PD\ GHYHORS RQ WKH OHQV VXUIDFH DQG LQWHUQDO SDUWV 7R SUHYHQW FRQGHQVDWLRQ LQ WKLV FDVH ¿UVW SXW WKH OHQV LQWR DQ DLUWLJKW SODVWLF EDJ EHIRUH WDNLQJ LW IURP D FROG WR ZDUP HQYLURQPHQW 7KHQ WDNH RXW WKH OHQV DIWHU LW KDV ZDUPHG JUDGXDOO\ 'R WKH VDPH ZKHQ WDNLQJ WKH OHQV IURP D ZDUP HQYLURQPHQW LQWR D FROG RQH ● 'R QRW OHDYH WKH OHQV LQ H[FHVVLYH KHDW VXFK DV LQ D FDU LQ GLUHFW VXQOL
6DIHW\ 3UHFDXWLRQV 7KLV GHYLFH FRPSOLHV ZLWK 3DUW RI WKH )&& 5XOHV 2SHUD LRQ LV VXEMHFW WR WKH IROORZLQJ WZR FRQGL LRQV 7KLV GHYLFH PD\ QRW FDXVH KDUPIXO LQWHUIHUHQFH DQG WKLV GHYLFH PXVW DFFHSW DQ\ LQWHUIHUHQFH UHFHLYHG LQFOXGLQJ LQWHUIHUHQFH WKDW PD\ FDXVH XQGHVLUHG RSHUDWLRQ 'R QRW PDNH DQ\ FKDQJHV RU PRGL¿FDWLRQV WR WKH HTXLSPHQW XQOHVV RWKHUZLVH VSHFL¿HG LQ WKH LQVWUXFWLRQV ,I VXFK FKDQJHV RU PRGL¿FDWLRQV VKRXOG EH PDGH \RX FRXOG EH UHTXLUHG WR VWRS RSHUD LRQ RI KH HTXLSPHQW
1RPHQFODWXUH )RFXV PRGH VZLWFK m 'LVWDQFH VFDOH m +RRG PRXQW m =RRP ULQJ m 5XEEHU ULQJ m )LOWHU 0RXQWLQJ 7KUHDG m =RRP ULQJ ORFN OHYHU DOVR VHUYHV DV D PDFUR VZLWFK m &RQWDFWV m )RFXVLQJ ULQJ m ,PDJH VWDELOL]HU VZLWFK m /HQV PRXQW LQGH[ m ● )RU GHWDLOHG LQIRUPDWLRQ UHIHUHQFH SDJH QXPEHUV DUH SURYLGHG LQ SDUHQWKHVHV o (1*
0RXQWLQJ DQG 'HWDFKLQJ WKH /HQV 6HH \RXU FDPHUD¶V LQVWUXFWLRQV IRU GHWDLOV RQ PRXQWLQJ DQG GHWDFKLQJ WKH OHQV 7KH OHQV PRXQW KDV D UXEEHU ULQJ IRU HQKDQFHG GXVW DQG ZDWHU UHVLVWDQFH 7KH UXEEHU ULQJ PD\ FDXVH VOLJKW DEUDVLRQV DURXQG WKH FDPHUD¶V OHQV PRXQW EXW WKLV ZLOO QRW FDXVH DQ\ SUREOHPV ,I WKH UXEEHU ULQJ EHFRPHV ZRUQ LW LV UHSODFHDEOH E\ D &DQRQ 6HUYLFH &HQWHU DW FRVW ● $IWHU GHWDFKLQJ WKH OHQV SODFH WKH OHQV ZLWK KH UHDU HQG XS WR SUHYHQW WKH OHQV VXUIDFH DQG FRQWDFWV IURP JHWWLQ
6HWWLQJ WKH )RFXV 0RGH 7R VKRRW LQ DXWRIRFXV $) PRGH VHW WKH IRFXV PRGH VZLWFK WR $) 7R VKRRW LQ PDQXDO IRFXV 0) PRGH VHW WKH IRFXV PRGH VZLWFK WR 0) DQG IRFXV E\ WXUQLQJ WKH IRFXVLQJ ULQJ 7KH IRFXVLQJ ULQJ DOZD\V ZRUNV UHJDUGOHVV RI WKH IRFXV PRGH =RRPLQJ 7R ]RRP URWDWH WKH ]RRP ULQJ %H VXUH WR ¿QLVK ]RRPLQJ EHIRUH IRFXVLQJ =RRPLQJ DIWHU IRFXVLQJ FDQ DIIHFW WKH IRFXV $IWHU DXWRIRFXVLQJ LQ 21( 6+27 $) PRGH IRFXV PDQXDOO\ E\ SUHVVLQJ WKH VKXWWHU EXWWRQ KDOIZD\ DQG WXUQLQJ
)L[LQJ WKH =RRP 5LQJ 7KH ]RRP ULQJ FDQ EH ¿[HG WR NHHS WKH OHQV DW WKH VKRUWHVW SRLQW 7KLV IXQFWLRQ LV FRQYHQLHQW IRU FDUU\LQJ D FDPHUD RQ D VWUDS EHFDXVH LW SUHYHQWV WKH OHQV IURP H[WHQGLQJ 1 5RWDWH WKH ]RRP ULQJ WR WKH 2 6OLGH WKH ]RRP ULQJ ORFN ZLGHVW SRVLWLRQ PP OHYHU LQ WKH GLUHFWLRQ LQGLFDWHG E\ WKH DUURZ ● 7R UHOHDVH WKH ]RRP ULQJ VOLGH WKH ]RRP ULQJ ORFN OHYHU LQ WKH GLUHFWLRQ RSSRVLWH WR WKH DUURZ 7KH ]RRP ULQJ FDQ RQO\ EH ORFNHG DW PD[LPXP ZLGH DQJOH (1*
6HWWLQJ IRU &ORVH XS 6KRRWLQJ 6HWWLQJ WKH ]RRP ULQJ WR PDFUR DOORZV IRU FORVH XS VKRRWLQJ 1 6OLGH WKH PDFUR VZLWFK ]RRP 2 5RWDWH WKH ]RRP ULQJ SDVW WKH 3 5HOHDVH WKH PDFUR VZLWFK ULQJ ORFN OHYHU WR 0$&52 .HHS \RXU ¿QJHU RQ WKH OHYHU VR WKDW LW GRHV QRW VOLGH EDFN WR LWV QRUPDO SRVLWLRQ WHOHSKRWR HQG PP LQWR WKH PDFUR UDQJH LQGLFDWHG E\ WKH \HOORZ OLQH ● $IWHU WKH ]RRP ULQJ KDV EHHQ VHW WR PDFUR WKH ]RRP ULQJ FDQ RQO\ EH RSHUDWHG ZLWKLQ WKH PDFUR UDQJH LQGLFDWHG E\ WKH \HOORZ OL
&ORVH XS 6KRRWLQJ 7KH \HOORZ OLQH RQ WKH GLVWDQFH VFDOH LQGLFDWHV WKH UDQJH LQ ZKLFK LPDJH GHJUDGDWLRQ LV PLQLPDO GXULQJ FORVH XS VKRRWLQJ 7KH IROORZLQJ SURFHGXUH VKRZV KRZ WR IRFXV ZLWKLQ WKH UDQJH LQGLFDWHG E\ WKH \HOORZ OLQH LQ RUGHU WR FDSWXUH SKRWRV ZLWK KLJK GH¿QLWLRQ +RZHYHU PD[LPXP PDJQL¿FDWLRQ LV [ ZKHQ VKRRWLQJ ZLWKLQ WKH UDQJH LQGLFDWHG E\ WKH \HOORZ OLQH RQ WKH GLVWDQFH VFDOH :H UHFRPPHQG XVLQJ D WULSRG IRU FORVH XS PDFUR VKRRWLQJ 1 $IWHU VHWWLQJ WKH ]RRP ULQJ WR PDFUR SRV
&ORVH XS 6KRRWLQJ ● 3OHDVH IRFXV FDUHIXOO\ VLQFH WKH GHSWK RI ¿HOG ZLWK FORVH XSV LV VKDOORZ ● 7KH IRFXVLQJ ULQJ GLVWDQFH VFDOH LV GHVLJQHG WR GLVSOD\ GLVWDQFHV GXULQJ QRUPDO VKRRWLQJ $V D UHVXOW LW GRHV QRW GLVSOD\ GLVWDQFHV GXULQJ FORVH XS VKRRWLQJ ● :KHQ WKH ]RRP ULQJ LV VHW WR WKH PDFUR UDQJH WKHUH DUH FDPHUDV WKDW ZLOO UHFRUG WKH IRFDO OHQJWK LQIRUPDWLRQ LQWR WKH LPDJH DW D YDOXH EHWZHHQ WKH UDQJH IURP DERYH PP WR PP GXH WR V\VWHP LVVXHV +RZHYHU WKH DFWXDOO\ IRFDO OHQJWK ZLOO QH
([SRVXUH GXULQJ &ORVH XS 6KRRWLQJ 6HWWLQJ WKH ([SRVXUH :KHQ WDNLQJ SKRWRJUDSKV XVLQJ 77/ PHWHULQJ QR H[SRVXUH FRPSHQVDWLRQ LV QHFHVVDU\ WR PHWHU WKH OLJKW FRPLQJ WKURXJK WKH OHQV :LWK 77/ PHWHULQJ $( DXWRH[SRVXUH LV SRVVLEOH DW DOO IRFXVLQJ GLVWDQFHV -XVW VHW WKH GHVLUHG SLFWXUH WDNLQJ PRGH WKHQ FKHFN WKH VKXWWHU VSHHG DQG DSHUWXUH EHIRUH WDNLQJ WKH SLFWXUH 0DJQL¿FDWLRQ DQG (IIHFWLYH I QXPEHU 7KH DSHUWXUH GLVSOD\HG E\ WKH FDPHUD DVVXPHV WKDW WKH IRFXV LV VHW WR LQ¿QLW\ 7KH DFWXDO DSH
,Q¿QLW\ &RPSHQVDWLRQ 0DUN ,QIUDUHG ,QGH[ ,Q¿QLW\ FRPSHQVDWLRQ PDUN 'LVWDQFH LQGH[ 7R FRPSHQVDWH IRU VKLIWLQJ RI WKH LQ¿QLW\ IRFXV SRLQW WKDW UHVXOWV IURP FKDQJHV LQ WHPSHUDWXUH 7KH LQ¿QLW\ SRVLWLRQ DW QRUPDO WHPSHUDWXUH LV WKH SRLQW DW ZKLFK WKH YHUWLFDO OLQH RI WKH GLVWDQFH VFDOH / PDUN LV DOLJQHG ZLWK WKH GLVWDQFH LQGH[ )RU DFFXUDWH PDQXDO IRFXVLQJ RI VXEMHFWV DW LQ¿QLW\ ORRN WKURXJK WKH YLHZ¿QGHU RU ORRN DW WKH PDJQL¿HG LPDJH RQ WKH /&' VFUHHQ ZKLOH URWDWLQJ WKH IRFXVLQJ ULQJ )RU
,PDJH 6WDELOL]HU
,PDJH 6WDELOL]HU ● 7KH VKRUWHU WKH VXEMHFW GLVWDQFH IURP WKH FDPHUD WKH OHVVHU WKH ,PDJH 6WDELOL]HU HIIHFW ZLOO EH ● 7KH ,PDJH 6WDELOL]HU FDQQRW FRPSHQVDWH IRU D EOXUUHG VKRW FDXVHG E\ D VXEMHFW WKDW PRYHG ● 6HW WKH 67$%,/,=(5 VZLWFK WR 2)) ZKHQ \RX DUH WDNLQJ SLFWXUHV XVLQJ WKH %XOE VHWWLQJ ORQJ H[SRVXUHV ,I WKH 67$%,/,=(5 VZLWFK LV VHW WR 21 WKH LPDJH VWDELOL]HU IXQFWLRQ PD\ LQWURGXFH HUURUV ● 7KH ,PDJH 6WDELOL]HU PD\ QRW EH IXOO\ HIIHFWLYH LI \RX VKRRW IURP D YLROHQWO\ VKDNLQJ YHKLFOH RU
,PDJH 6WDELOL]DWLRQ GXULQJ &ORVH XS 6KRRWLQJ )RU QRUPDO FORVH XS VKRRWLQJ WKH KLJKHU WKH PDJQL¿FDWLRQ WKH IDVWHU WKH VKXWWHU VSHHG PXVW EH WR SUHYHQW EOXU FDXVHG E\ FDPHUD VKDNH $OWKRXJK LW GHSHQGV RQ WKH VKRRWLQJ FRQGLWLRQV XVXDOO\ WKH VKXWWHU VSHHG PXVW EH DW OHDVW RQH RU WZR VWRSV IDVWHU WKDQ QRUPDO 7KH PDJQL¿FDWLRQ UHIHUV WR WKH UDWLR EHWZHHQ WKH VXEMHFW¶V VL]H DQG WKH FRUUHVSRQGLQJ LPDJH VL]H RQ WKH IRFDO SODQH 7KH () PP I / ,6 860 LV LQVWDOOHG ZLWK DQ ,PDJH 6WDELOL]HU WKDW J
7DNLQJ +DQG KHOG &ORVH XSV &ORVH XS VKRWV DUH PRUH SURQH WR EH DIIHFWHG E\ FDPHUD VKDNH WKDQ ZLWK QRUPDO VKRRWLQJ 7KH ,PDJH 6WDELOL]HU¶V FRUUHFWLYH HIIHFW LV WKHUHIRUH OHVV GXULQJ FORVH XSV WKDQ GXULQJ QRUPDO VKRRWLQJ HYHQ ZLWK WKH VDPH GHJUHH RI FDPHUD VKDNH 7KH GHSWK RI ¿HOG DOVR EHFRPHV YHU\ VKDOORZ ZLWK FORVH XSV DQG PRYLQJ IRUZDUG RU EDFN HYHQ VOLJKWO\ ZLOO WKURZ RII WKH IRFXV 3ODFH ERWK HOERZV RQ D VWHDG\ VXUIDFH VXFK DV D WDEOH :KHQ KDQG KROGLQJ WKH FDPHUD IRU FORVH XS VKRRWLQJ PLQ
+RRG 7KH (: / KRRG FXWV RXW XQZDQWHG OLJKW DQG SURWHFWV WKH IURQW RI WKH OHQV IURP UDLQ VQRZ DQG GXVW %XWWRQ Ɣ$WWDFKLQJ 7R DWWDFK WKH KRRG DOLJQ WKH KRRG¶V DWWDFKPHQW SRVLWLRQ PDUN ZLWK WKH UHG GRW RQ WKH IURQW RI WKH OHQV WKHQ WXUQ WKH KRRG DV VKRZQ E\ WKH DUURZ XQWLO WKH OHQV¶ UHG GRW LV DOLJQHG ZLWK WKH KRRG¶V VWRS SRVLWLRQ PDUN Ɣ5HPRYLQJ 7R UHPRYH WKH KRRG KROG GRZQ WKH EXWWRQ RQ WKH VLGH DQG WXUQ WKH KRRG LQ WKH GLUHFWLRQ RI WKH DUURZ XQWLO WKH SRVLWLRQ PDUN RQ WKH KRRG DOLJQV
)LOWHUV 6ROG VHSDUDWHO\
6SHFL¿FDWLRQV )RFDO /HQJWK $SHUWXUH PP I /HQV &RQVWUXFWLRQ JURXSV HOHPHQWV 0LQLPXP $SHUWXUH I $QJOH RI 9LHZ 'LDJRQDO ± 9HUWLFDO ± ƍ +RUL]RQWDO ± 0LQ )RFXVLQJ 'LVWDQFH P IW P IW LQ WKH PDFUR UDQJH ZRUNLQJ GLVWDQFH RI DSSUR[ FP LQ 0D[ 0DJQLILFDWLRQ [ DW PP [ LQ WKH PDFUR UDQJH )LHOG RI 9LHZ $SSUR[ [ ± [ PP [ ± [ LQFK DW P IW )LOWHU 'LDPHWHU PP
CT1-8585-001 1012Ni © CANON INC.
Cak•,..,.O,... • '•• Complete this card at time of sale. A remplir au moment de l'achat PRESENT OWNERSHIP AND PRODUCTS INTERESTED IN Articles deja en possession ou juges dignes d'interet CAMERAS APPAREILS -PHOTO canOiJI Dealer Record of Canon Purchase Fiche d' Achat our Concessionnaire Canon (Camera) (Appareil) (Camera) (Appareil) INTERCHANGEABLE LENS Objectif interchangeable CANON U.S.A., INC. 1111111111111111111111111111111111111111 CANON CANADA INC.
Canon CANON®EF Lens and Accessories Limited WarrantyFor U.S.A. & Canada Only T he limited warranty set forth below is given by Canon U.S.A ., Inc. (Canon U.S.A.) in the United States or Canon Canada, Inc.
Ca11011 Garantie limitee des _objectifs EF et des accessoires de CANON®Pour les Etats-Unis et le Canada seulement La pn§sente garantie limitOO est fournie par Canon U.S.A., Inc_(Canon U.S.A.) aux Etats-Unis ou Canon Canada, Inc. (Canoo Canada) au Canada a regard des objectifs EF de marque Canon. des accessokes livres avec cette garantie limitee (collectivement les « produits " ).lorsqu'ils sont achetes et utilises aux Etats-Unis ou au Canada.
REMARKS Canon i Canon U.S.A. You may obtain technical support for your Products as follows: • Internet support at www.usa.canon .com/support (E·mail support also available) • Telephone assistance from a Canon U.S.A. Customer Care representative free of charge during regular business hours at 1-800-0K-CANON (1-800-652-2666). Canon Canada You may obtain technical support for your Products as follows: • Internet support for English at www.canon.