C Y P O This manual is for the EOS-1D C installed with firmware version 1.1.0 or later. Read this manual together with the EOS-1D X Instruction Manual (firmware version 1.2.0 or later) and EOS-1D X Wired LAN Instruction Manual. The “Software Start Guide” is included at the end of this manual.
Introduction Based on the top-of-the-line EOS-1D X, the EOS-1D C is a digital SLR camera with enhanced movie shooting functions. Its advanced movie shooting functions include a full-frame (approx. 36 x 24 mm) CMOS sensor with approx. 18.1 effective megapixels to create beautiful and impressive background blur effects, high ISO speeds for low-light shooting, 4K (4096 x 2160 pixels) movie recording, Full HD 60p/50p, Super 35mm Crop, Canon Log gamma, and uncompressed movie output via HDMI.
Instruction Manuals The EOS-1D C comes with three manuals: 1. EOS-1D C Instruction Manual (this booklet), 2. EOS-1D X Instruction Manual, and 3. EOS-1D X Wired LAN Instruction Manual. For movie shooting, refer to 1. For basic operations, still photo shooting, playback functions, wired LAN functions, and other information not in 1, see manuals 2 and 3 as they are basically common with those of the EOS-1D X.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer.
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0, 9, 7, 8 : Indicates the Main Dial. : Indicates the Quick Control Dial. : Indicates the Multi-controller. : Indicates the Setting button. : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec. respectively after you let go of the button.
Contents Introduction 2 Instruction Manuals .......................................................................... 3 Item Check List................................................................................. 4 Conventions Used in this Manual ..................................................... 5 Handling Precautions ....................................................................... 8 Nomenclature .................................................................................
Contents 2 Reference 61 Differences with the EOS-1D X Instruction Manual ........................ 62 System Map .................................................................................... 66 Menu Settings ................................................................................. 68 Troubleshooting Guide.................................................................... 70 Specifications.................................................................................. 76 Safety Warnings.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there may be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Nomenclature Lens mount index Mirror Depth-of-field preview button Movie microphone (p.39) Multi-function button 2 Self-timer lamp Lens lock pin Shutter button (p.18) Lens release button Lens mount Grip Vertical-grip Multi-function button 2 Vertical-grip on/off switch Vertical-grip AF area selection mode/ Multi-function/ Multi-spot metering button C Y P O Tripod socket Body number Vertical-grip Main Dial (p.19) Vertical-grip shutter button (p.
Nomenclature White balance selection button Exposure compensation/ Aperture button AF area selection mode/Multi-function/ Multi-spot metering button LCD panel illumination button Hot shoe ISO speed setting button (p.23) Flash-sync contacts <6> Main Dial Eyecup Strap mount C Y P O <9> Multi-controller <0> Setting button <5> Quick Control Dial (p.18) LCD monitor Quick Control button Touch pad (p.42) Power/Multi function lock switch Vertical-grip AF start button (p.
Nomenclature Top LCD panel Focal plane mark Metering mode selection/Flash exposure compensation button Live View shooting/ Movie shooting button (p.16) Shooting mode selection button (p.18) AF start button (p.28) AE lock button (p.22) AF mode selection/ Drive mode selection button AF point selection button AEB setting button System extension mounting hole C Y P O Eyepiece shutter lever Speaker (p.
Nomenclature Info button (p.57) Menu button Card slot 1 Strap mount Card slot 2 Card slot cover Terminal cover Card 1 eject button Network lamp Playback button (p.57) Card/ Image size selection button C Index/Magnify/ Reduce button System extension terminal External microphone IN terminal (p.39) Remote control terminal (N3 type) Headphone terminal (p.
Using the Cable Protector and Clamp With a Canon HDMI cable (sold separately): 1 2 Interface cable HDMI cable (sold separately) Cable protector 3 Cable clamp C 4 Y P O With a third party HDMI cable (commercially available): 1 2 3 4 If the plug of a third-party HDMI cable can fit into the Cable protector, using the Cable protector is recommended.
Shooting and Playing Movies Y P O The live image displayed on the camera’s LCD monitor can be recorded as a movie to the card. The movie recording format will be MOV. C This chapter assumes that an EF lens is used with the camera. If you use an EF Cinema (CN-E) lens, see the cautions on pages 17 and 29, and start movie shooting.
k Preparing to Shoot Movies Set the camera so it can record the live image displayed on the LCD monitor as a movie. To shoot still photos, see page 31. 1 Check the [Movies] setting. Select the [z4] tab and check that [LV z/k set.] is set to [Movies]. If it is set to [Disable] or [Stills], select [Movies], then press <0>. “LV” stands for Live View. rec. size]. 2 SetFor[Movie details on [Movie rec. size], see Y P O page 34. C the image. 3 Display Press the button.
k Preparing to Shoot Movies EF Cinema (CN-E) Lenses With EF Cinema single focal length lenses, you can shoot at all movierecording quality settings. If you use an EF Cinema zoom lens, you can shoot movies only with I Super 35mm Crop. (Since the image circle is small, the image periphery will be dark if you shoot a movie in H A B C quality or still photo.) Cards that Can Record Movies Use a large-capacity card with a fast writing/reading speed (required card performance) as shown in the table.
k Shooting Movies Autoexposure Shooting When the shooting mode is set to or , autoexposure control will take effect to suit the scene’s current brightness. Autoexposure control will be the same for and . 1 Set the shooting mode to . Press the button and turn the <6> or <5> dial to select or . the subject. 2 Focus Before shooting a movie, focus with AF Y P O or manual focus (zp.213 to 220).
k Shooting Movies Shutter-priority AE When the shooting mode is , you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the shooting mode to . Press the button and turn the <6> or <5> dial to select . the desired shutter speed. 2 SetWhile looking at the LCD monitor, Shutter speed C3 Y P O turn the <6> dial. The settable shutter speeds depend on the frame rate <9>.
k Shooting Movies Aperture-priority AE When the shooting mode is , you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the shooting mode to . Press the button and turn the <6> or <5> dial to select . the desired aperture. 2 SetWhile looking at the LCD monitor, Y P O turn the <6> dial. Aperture C and shoot the movie.
k Shooting Movies ISO speed in the d, s, f, and BULB modes The ISO speed will be set automatically within ISO 100 - 25600. Under [z2: ISO speed settings], if [ISO speed range]’s [Maximum] setting (zp.130) is set to [51200/H] in the d, s, and BULB modes, the automatic ISO speed setting range’s maximum will be expanded to H (equivalent to ISO 51200). Note that even if you set [Maximum] to [51200], the maximum will remain at ISO 25600 and will not be expanded.
k Shooting Movies Notes for Autoexposure, Shutter-priority AE, and Aperture-priority AE You can lock the exposure (AE lock) by pressing the button (zp.181). After applying AE lock during movie shooting, you can cancel it by pressing the button. (AE lock setting is retained until you press .) If you set the power switch to <1> and turn the <5> dial, you can set the exposure compensation. Pressing the shutter button halfway displays the ISO speed and shutter speed on the screen’s bottom.
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. 1 Set the shooting mode to . Press the button and turn the <6> or <5> dial to select . the ISO speed. 2 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> or <5> dial to set the ISO speed. For details on the ISO speed, see the next page. Y P O the shutter speed and aperture.
k Shooting Movies ISO speed during manual-exposure shooting ISO 400 is set by default. You can set the ISO speed manually within ISO 100 - 25600 in 1/3stop increments. Under [z2: ISO speed settings], if [ISO speed range]’s [Maximum] is set to [51200/H], the manual ISO speed setting range’s maximum will be expanded to H (equivalent to ISO 51200). Note that even if you set [Maximum] to [51200], the maximum will remain at ISO 25600 and not be expanded.
k Shooting Movies Since shooting a movie at ISO 32000/40000/51200 may result in substantial noise, these speeds are designated as expanded ISO speeds (displayed as [H]). If [ISO speed range]’s [Minimum] is set to [L (50)] and you switch from still photo shooting to movie shooting, the manual ISO speed setting range’s minimum for movie shooting will be ISO 100. It cannot be expanded to ISO 50.
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies Notes on Movie Shooting The camera cannot autofocus continuously like a camcorder. If you use AF during movie shooting, the focus may become greatly blurred momentarily and the exposure may change. If you use a USM lens and perform AF while shooting a movie in low light, horizontal noise stripes may be recorded. With certain lenses having an electronic focusing ring, horizontal noise stripes may be recorded even when you focus manually (MF).
k Shooting Movies Notes on Movie Shooting Movie-related settings are under the [z4] and [z5] tabs (p.51). A movie file is recorded each time you shoot a movie. If the file size exceeds 4 GB for a single movie shoot (single clip), a new file will be created. The movie image’s field of view is approx. 100% (with movie recording size set to [A]). You can also focus the image by pressing the
button. To focus during movie shooting, press the
button. You cannot focus by pressing the shutter button.
k Shooting Movies Cautions for Using EF Cinema (CN-E) Lenses EF Cinema lenses with PL mount are not supported. EF Cinema lenses require the aperture to be adjusted manually. Therefore, they are not suitable for autoexposure shooting (p.18) and shutter-priority AE shooting (p.19) for which the aperture is set automatically to suit the brightness. If the EF Cinema lens is not fitted with a function for sending information to the camera, the aperture will be indicated as “00.
k Shooting Movies Final Image Simulation The final image simulation is a function that allows you to see the effects of the Picture Style, white balance, etc., on the image. During movie shooting, the image displayed will automatically reflect the effects of the settings listed below. Final image simulation for movies Picture Style * All settings such as sharpness, contrast, color saturation, and color tone will be reflected.
k Shooting Movies Shooting Still Photos Set [z5: Movie shoot. btn] to [o] (p.52) and press the shutter button completely. You can then shoot still photos while shooting the movie. Note that you cannot shoot still photos if H, I, A:8/7, or Canon Log gamma is set. Taking still photos during movie shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx. 1 sec. The movie and still photo will be recorded as separate files on the card.
k Shooting Movies If [z5: Movie shoot. btn] is set to [V/o], still photo shooting is not possible. Since the image circle of EF Cinema zoom lenses does not support the image size of 35mm full-frame size image sensor, still photo shooting is not possible. (The image periphery will look dark.) AEB cannot be used. Even if an external Speedlite is used, it will not fire. Continuous still photo shooting is possible during movie shooting. However, the captured images will not be displayed on the monitor.
Shooting Function Settings W / f / R / S / i / O / B Settings If you press the , , , , , or button while the image is displayed on the LCD monitor, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective function. When f is set, you can press the button to select the AF area selection mode and AF point. The procedure is the same as with viewfinder shooting. During manual-exposure shooting (p.
3 Setting the Movie-recording Size The menu option [z4: Movie rec. size] enables you to set the movie’s image size, frame rate per second, and movie recording/compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image size H [4096x2160] : The image at the center of the image sensor is recorded in 4K resolution. The effective angle of view is approx. 1.3 times the lens focal length.
3 Setting the Movie-recording Size Image Area When H, I, A, or B is set, the respective image sensor area below is used to record the movie. H 4K Still photos C SD A Full HD/B HD Y P O I Super 35mm Crop C When I or A is set, the movie will be recorded in 1920x1080 resolution. When B is set, the movie will be recorded in 1280x720 resolution. When C is set, the movie will be recorded in 640x480 resolution.
3 Setting the Movie-recording Size Frame rate (fps: frames per second) 8/6 : For areas where the TV format is NTSC (North America, Japan, Korea, Mexico, etc.). 7/5 : For areas where the TV format is PAL (Europe, Russia, China, Australia, etc.). 4 : Mainly for motion pictures. Movie recording method and compression method J MJPG : When shooting in H, Motion JPEG is used to compress the movie recorded. Each frame is compressed separately and recorded without compression between frames.
3 Setting the Movie-recording Size Total Movie Recording Time and File Size Per Minute Movie-Recording Size H 54 I File Size (approx.) J 3.76 GB/min. Total Recording Time (approx.) 4 GB Card 32 GB Card 128 GB Card 55 sec. 8 min. 32 min. 654 X 385 MB/min. 9 min. 30 sec. 1 hr. 19 min. 5 hr. 16 min. 654 W 685 MB/min. 2 hr. 57 min. 87 5 min. 44 min. W 1.36 GB/min. 2 min. 30 sec. 1 hr. 29 min. 2 hr. 9 min. 8 hr. 37 min. A 654 X 235 MB/min. 654 W 685 MB/min. 5 min. 44 min. 2 hr.
3 Setting the Movie-recording Size An increase of the camera’s internal temperature may cause movie shooting to stop before the maximum recording time shown on the preceding page (p.55). Even if [Record func.] is set to [Auto switch card], the card cannot be switched automatically during movie shooting.
3 Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or with a commerciallyavailable stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [z4: Sound recording]. Sound Recording/Sound-Recording Level [Auto] [Manual] [Disable] : The sound-recording level is adjusted automatically. Auto level control will operate automatically in response to the sound level.
3 Setting the Sound Recording Using the microphone The built-in microphone records monaural sound. Stereo sound recording is possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (3.5 mm) to the camera’s external microphone IN terminal (p.13). When an external microphone is connected, sound recording will switch automatically to the external microphone. C Y P O The sound volume balance between L (left) and R (right) cannot be adjusted.
3 Setting the Sound Recording Using headphones By connecting stereo headphones (commercially available) equipped with a 3.5 mm mini plug to the camera’s headphone terminal (p.13), you can listen to the sound during movie shooting. If you are using an external stereo microphone, you can listen to the sound in stereo. To adjust the headphone’s sound volume, press the button, then hold down the button and tilt the <9> up or down. The sound volume level is not displayed on the screen.
3 Silent Control This function is convenient when you want to change the ISO speed, sound-recording level, etc., silently while shooting a movie. When [z5: Silent Control] is set to [Enable h], you can use the touch pad on the inner ring of the Quick Control Dial. You can operate the camera silently just by touching the top, bottom, left, or right of . During movie shooting, you can press to display the Quick Control screen and change the settings below with .
Setting the Canon Log Gamma Canon Log gamma is gamma correction for post-production. It is geared to maximize the image sensor’s characteristics and attain a wide dynamic range. It minimizes loss of shadow and highlight details, and tonal information from the shadows to highlights can be incorporated in the movie. A movie shot with Canon Log gamma can be applied with a lookup table (LUT) during post-production. Download the LUT data from the Canon Web site. 1 Select [Canon Log settings].
Setting the Canon Log Gamma the Canon Log gamma. 4 Adjust Adjust as necessary. Turn the <5> dial to select a parameter ([Sharpness], [Saturation], [Hue]), then press <0>. Turn the <5> dial to set the parameter, then press <0>.
Setting the Canon Log Gamma Setting View Assist Canon Log gamma is a movie characteristic to attain wide dynamic range. As a result, the image displayed on the LCD monitor has low contrast and is somewhat dark compared to when a Picture Style is set. With View Assist, the movie image will be displayed on the LCD monitor with a conspicuous characteristic. This makes it easier to check the angle of view, details, etc. Note that even if View Assist is set, it will not affect the movie recorded to the card.
Setting the Canon Log Gamma When [Peripheral illumin.] is set to [Enable], Canon Log gamma icon on the information display screen (p.26) blinks, since noise may appear in the movie image periphery. If you set Canon Log gamma, Picture Style, Auto Lighting Optimizer, and highlight tone priority cannot be set (not applied) for movie shooting. Also, still photo shooting during movie shooting is not possible. If you set Canon Log gamma, although AF is not possible, AF point (p.
3 Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Set the time code with [z5: Time code]. Count Up [Rec run] [Free run] : The time code counts up only while you are shooting a movie. The time code will be continuous across sequential movie files.
3 Setting the Time Code Movie Recording Count You can select what to display on the movie-shooting screen. [Rec time] : Indicates the elapsed time from the start of the movie shooting. [Time code] : Indicates the time code during movie shooting. Shooting still photos during movie shooting will cause a discrepancy between the actual time and time code. Regardless of the [Movie rec count] setting, the time code will always be recorded to the movie file.
3 Setting the Time Code HDMI Time code You can append the time code to a movie that was output from HDMI. This is convenient for proxy editing after the movie output from HDMI is recorded to an external recording device (p.54). [On]: Time code is appended to the HDMI output image. [Off]: Time code is not appended to the HDMI output image.
3 Setting the Time Code Drop Frame If the frame rate setting is 6(29.97 fps) or 8(59.94 fps), the time code’s frame count causes a discrepancy between the actual time and time code. This discrepancy can be corrected automatically. This correction function is called drop frame. [Enable] : The discrepancy is corrected automatically by skipping time code numbers (DF: Drop frame). [Disable] : The discrepancy is not corrected (NDF: Non-drop frame).
3 Menu Function Settings [z4] Menu When you select [Movies] under [z4: LV z/k set.], the [z4] [z5] tabs for movie shooting will appear. The menu options are as follows. AF mode The AF modes are the same as described on zpages 213 to 219. You can select [Live mode], [u Live mode], or [Quick mode]. Note that continuous focusing of a moving subject is not possible. Even if the AF mode is set to [Quick mode], it will switch to [Live mode] during movie shooting.
3 Menu Function Settings Silent LV shooting This function applies to still photo shooting. For details, see zpage 212. Metering timer You can change how long the exposure settings are displayed (AE lock time). [z5] Menu Y P O Time code You can set the time code. For details, see pages 47 to 50. C Silent Control When [Enable h] is set, you can use the touch pad and Quick Control screen to change settings silently during movie shooting. For details, see page 42.
3 Menu Function Settings HDMI output + LCD Movies displayed on the LCD monitor as they are being recorded can also be displayed from the HDMI output. The default setting is [Mirroring]. Note that the video from the HDMI output will be displayed without the shooting information or masking for indicating image area (output without information overlay: through display). This makes it convenient to record the HDMI output image to a commercially-available external recording device.
3 Menu Function Settings By pressing the button, you can change the information displayed on the screen. You can append a time code to the HDMI output image (p.49). Canon Log settings This is a gamma for attaining wide dynamic range in postproduction. For details, see pages 43 to 46. [53] Menu Y P O HDMI frame rate You can set the HDMI output frame rate to [Auto], [24p], or [60i/50i].
Movie Shooting Cautions White and Red Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a white icon will appear. Even if you shoot a movie while this icon is displayed, the movie’s image quality will hardly be affected. However, if you shoot still photos, the image quality of the still photos may deteriorate.
Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator becomes full, movie shooting will stop automatically.
k Playing Movies 1 Play back the image. Press the button. X The last captured image or last image viewed will appear. a movie. 2 Select To play back images starting with the last image, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. With the single-image display, the <1s> icon displayed on the upper left indicates a movie. Each time you press the button, the display format will change.
k Playing Movies Index display Press the button and turn the <6> dial counterclockwise to display the index. In the index display, perforations at the left edge of a thumbnail indicate a movie. As movies cannot be played on the index display, press <0> to switch to the single-image display. the single-image display, press 3 In<0>. X The movie playback panel will appear at the bottom of the screen. Y P O the movie. 4 PlayTurnback the <5> dial to select [7] (Play), then press <0>.
k Playing Movies Function Playback Description 2 Exit Returns to the single-image display. 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by turning the <5> dial. The slow-motion speed is indicated at the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie.
B: Shooting Information Display Sample Information for Movies Shooting time, Playback time/ Time code Playback Shutter speed Aperture Shooting mode Canon Log gamma/ Picture Style Movie recording size File size Frame rate Movie recording/compression method C Y P O If you use HDMI output to play a H movie, it will be played in Full HD (1080 60i/50i). However, using EOS MOVIE Utility (p.95) enables you to play the movie in H quality.
Reference Y P O This chapter covers other differences with the EOS-1D X’s Instruction Manual, system accessories, and an FAQ.
Differences with the EOS-1D X Instruction Manual As explained on page 3, the EOS-1D C Instruction Manual centers on movie shooting. Other differences between this manual and the EOS-1D X Instruction Manual (Firmware version 1.1.0 or later) are outlined below. Nomenclature: Rear LCD panel (zp.26) The EOS-1D C’s rear LCD panel does not display the movie-recording size. Reverting the Camera to the Default Settings (zp.
Differences with the EOS-1D X Instruction Manual w: Registering Custom Shooting Modes (zp.354 to 356) With the EOS-1D C, the following functions are added and registered. [z5 (Movie)] HDMI output + LCD, and Canon Log settings [53] HDMI frame rate When [Canon Log] is set to [On] and Custom shooting mode , , or is set, the shooting mode will also be switched to . Be aware that the shooting mode may be updated when [Auto update set.] is set to [Enable].
Differences with the EOS-1D X Instruction Manual Setting the Image-Recording Quality: Guide to Image Size Settings (Approx.) (zp.124) Only the “Maximum Burst” numerals in bold frame are different from those of EOS-1D X. Image Size Pixels Recorded Printing (megapixels) Size File Size (MB) Possible Shots Maximum Burst 3 18M Around A2 6.0 1200 100 (160) H 14M A3 or larger 4.8 1470 150 (280) 5 8.0M Around A3 3.3 2170 290 (860) 6 4.5M Around A4 2.
Differences with the EOS-1D X Instruction Manual The file size, possible shots, and maximum burst during continuous shooting are based on Canon’s 8 GB testing card and Canon’s testing standards (JPEG quality 8, ISO 100, and Standard Picture Style). These figures will vary depending on the subject, card brand, ISO speed, Picture Style, Custom Functions, and other settings. The maximum burst applies to high-speed continuous shooting.
System Map ST-E2 ST-E3-RT 270EX II 90EX 320EX 430EX II 600EX-RT/ Macro Ring Lite Macro Twin Lite MR-14EX MT-24EX 600EX Bundled Accessories Angle Finder C Eyecup Eg Wide Strap L7 C Y P O Cable Protector and Clamp CR2025 lithium battery Dioptric Adjustment Lenses Eg Anti-Fog Eyepiece Eg Hand Strap E2 Focusing Screen Ec series EOS DIGITAL Software Instruction Solution Disk Manual Battery Pack LP-E4N AC Adapter Kit ACK-E4 Battery Charger LC-E4N * Battery Pack LP-E4 and Battery Charger LC-E4
System Map GPS Receiver GP-E2 Headphone Timer Remote Remote Switch Controller RS-80N3 TC-80N3 Wireless Controller LC-5 EF lenses External microphone Interface Cable IFC-200U (1.9 m/6.2 ft.) Y P O HDMI Cable HTC-100 (2.9 m/9.5 ft.) Stereo AV Cable AVC-DC400ST (1.3 m/4.3 ft.) C Interface Cable IFC-500U (4.7 m/15.4 ft.
Menu Settings For Movie Shooting z: Shooting 4 (Movie) (Red) Page LV z/k setting Disable / Stills / Movies 16 AF mode Live mode / u Live mode / Quick mode 51 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 51 Movie recording size H:4096x2160 (5 / 4) (J) I:1920x1080 (6 / 5 / 4) (W / X) 1920x1080 (8 / 7) (W) 1920x1080 (6 / 5 / 4) (W / X) 1280x720 (8 / 7) (W / X) 640x480 (6 / 5) (X) 34 Sound recording Recording level Sound recording: Auto / Manual / Disable Y P O 39 Wind filter: Disable / Enab
Menu Settings z: Shooting 5 (Movie) (Red) Page Time code Count up / Start time setting / Movie rec count / Movie play count* / HDMI / Drop frame 47 Silent Control Enable h / Disable h 42 Movie shooting button o / V/o 52 HDMI output + LCD Mirroring / No mirroring 53 Canon Log settings Canon Log / View Assist. / Sharpness / Saturation / Hue 43 * The setting is linked to [Movie play count] under the [x3] tab (zp.372). 5: Set-up 3 (Yellow) Video system NTSC / PAL Battery info.
Troubleshooting Guide A white icon or red E icon is displayed. This indicates that the camera’s internal temperature is high. If the white < > icon is displayed, still photo image quality may deteriorate. If the red icon is displayed, movie shooting will soon stop automatically (p. 55). Movie shooting stops by itself. If the card’s writing speed is slow, movie shooting may stop automatically.
Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie when [Maximum: 51200] is set with [ISO speed range] and ISO speed is set to ISO 32000/40000/51200, the ISO speed will switch to ISO 25600 (during movie shooting with manual exposure). Even if you switch back to still photo shooting, the ISO speed will not revert to the original setting.
Troubleshooting Guide The screen flickers or horizontal stripes appear. Flickering, horizontal stripes (noise), or irregular exposures can be caused by fluorescent light, LED bulbs, or other light sources during movie shooting. Also, changes in the exposure (brightness) or color tone may also be recorded. In the mode, a slow shutter speed may solve the problem. When I shoot still photos during movie shooting, the movie shooting stops.
Troubleshooting Guide Shooting mode is automatically set to or cannot shoot with ISO Auto. When Canon Log gamma is set, shooting mode will be automatically switched to manual exposure. If ISO Auto is set, it will be automatically switched to manual ISO speed setting (p.43). Vertical noise stripes appear. When Canon Log gamma is set, vertical noise stripes may appear in movies depending on subject or shooting conditions. For details, see page 44.
Troubleshooting Guide AF is not possible. AF is not possible when Canon Log gamma is set. If H, I or A:8/7 is set, AF is not possible in the f mode. Even if the AF mode is set to f, it will switch to d during movie shooting. The time code cannot be appended during HDMI output. If the movie-recording quality’s frame rate setting is set to a value that does not function properly in combination with the NTSC/PAL frame rate, the time code will not be appended to the HDMI output image.
Troubleshooting Guide Movie Playback Problems The movie cannot be played back. Movies edited with a personal computer cannot be played back with the camera. Movies shot with Canon Log gamma or shot in H, A:8/7 cannot be played back by another EOS DIGITAL camera. When the movie is played back, camera operation noise can be heard. If you operate the camera’s dials or lens during movie shooting, the operation noise will also be recorded.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera Type I or II CF card, UDMA mode 7-compatible * Dual CF card slots Approx. 36.0 x 24.0 mm 1. Canon EF lenses (except EF-S and EF-M lenses) 2. Canon Cinema (CN-E) lenses (EF mount) * The effective angle of view is equivalent to the lens focal length. * Canon EF Cinema zoom lenses are compatible only with Super 35mm Crop movies.
Specifications • Image Processing During Shooting Picture Style: White balance: Auto, Standard, Portrait, Landscape, Neutral, Faithful, Monochrome, User Def. 1 - 3 Auto, Preset (Daylight, Shade, Cloudy, Tungsten light, White fluorescent light, Flash), Custom, Color temperature setting (Approx.
Specifications AF area selection modes: Single-point Spot AF (manual selection), Single-point AF (manual selection), AF point expansion (manual selection: up, down, left, and right), AF point expansion (manual selection: surround), Zone AF (manual selection), 61-point automatic selection AF AF point automatic selection conditions: Depending on EOS iTR AF setting (AF using color and face detection information possible) * iTR: Intelligent Tracking and Recognition AF Configuration tool: Case 1 - 6 AI Servo ch
Specifications Standard exposure level adjustment: AE Microadjustment possible • Multiple Exposures Shooting method: Function/control priority, Continuous shooting priority Number of multiple exposures: 2 to 9 exposures Multiple-exposure control: Additive, Average, Bright, Dark • Shutter Type: Shutter speeds: Electronically-controlled, focal-plane shutter 1/8000 sec. to 30 sec., Bulb (Total shutter speed range. Available range varies by shooting mode.), X-sync at 1/250 sec.
Specifications • Live View Shooting Focus modes: Live mode, Face detection Live mode (contrast detection), Quick mode (phase-difference detection), Manual focusing (approx. 5x / 10x magnification possible) Focusing brightness range: EV 1 - 20 (with contrast detection, at 23°C/73°F, ISO 100) Metering modes: Evaluative metering with the image sensor EV 0 - 20 (at 23°C/73°F with EF50mm f/1.
Specifications Pixel range: Movie characteristic: 8 bit, 0 to 255 (with Canon Log Gamma: 8 bit, 16 to 254) 1. Canon Log gamma, 2. Picture Style selectable * If Canon Log gamma is set, View Assist is possible. Required card 4K: UDMA7 100 MB/sec. or higher performance: Full HD 60p/50p: 60 MB/sec. or higher (Writing/reading speed) Super 35mm Crop/IPB: 20 MB/sec. or higher Other than the above: IPB: 10 MB/sec. or higher, ALL-I: 30 MB/sec.
Specifications Two-screen display: Simultaneous display of LCD monitor and HDMI output image is possible. HDMI output: Image without information display can be output. * Selectable from Auto, 24p, 60i, and 50i. Accessory attachment: Camera bottom provides an alignment hole to prevent rotation. • LCD Monitor Type: TFT color, liquid-crystal monitor Monitor size and dots: Wide, 8.1 cm (3.2-in.) (3:2) with approx. 1.
Specifications • Direct Printing Compatible printers: Printable images: Print ordering: PictBridge-compatible printers JPEG and RAW images DPOF Version 1.
Specifications • Power Battery: Battery information: Battery life: (Based on CIPA testing standards) Movie shooting time: Date/Time battery: Battery Pack LP-E4N/LP-E4 (Quantity 1) * AC power can be supplied via AC Adapter Kit ACK-E4 Remaining capacity, Shutter count, and Recharge performance displayed With viewfinder shooting: Approx. 1120 shots at 23°C/73°F, approx. 860 shots at 0°C/32°F With Live View shooting: Approx. 290 shots at 23°C/73°F, approx. 250 shots at 0°C/32°F Approx. 1 hr. 25 min.
Specifications All the data above is based on Canon’s testing standards and CIPA (Camera & Imaging Products Association) testing standards and guidelines. Dimensions, maximum diameter, length and weight listed above are based on CIPA Guidelines (except weight for camera body only). Product specifications and the exterior are subject to change without notice. If a problem occurs with a non-Canon lens attached to the camera, consult the respective lens maker.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Macintosh and Mac OS are trademarks or registered trademarks of Apple Inc. in the United States and other countries. CompactFlash is a trademark of SanDisk Corporation. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Use of genuine Canon accessories is recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of nongenuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
MEMO C 90 Y P O
MEMO C Y P O 91
MEMO C 92 Y P O
Software Start Guide Y P O This chapter gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM) provided with the camera and explains how to install the software on a personal computer. It also explains how to view the PDF files on the Software Instruction Manual CD-ROM.
Software Start Guide EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a personal computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use the personal computer to set various camera settings and shoot remotely with the computer connected to the camera.
Software Start Guide Downloading from Canon Web site The following software can be downloaded from Canon Web site. EOS MOVIE Utility for EOS-1D C [On Windows] You can play back movies you shot, consecutively play back separate movie files, and save them as a single movie file with this software. Exporting still photos from movies is also possible. [On Macintosh] You can save separate movie files as a single movie file with this software.
Software Start Guide Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Instruction Manual PDFs 1 Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. 2 Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. 3 Copy the [English] folder to your computer. Y P O Instruction Manual PDFs with the names below are copied.
Index Numerics Free run.......................................... 47 B (1280x720) ...............................34 Full HD ..................................... 34, 38 A (1920x1080) .............................34 Full High-Definition (Full HD).......... 34 I (1920x1080) ............................34 H (4096x2160) .............................34 C (640x480).................................34 A G Grid display .................................... 51 H HD ............................................
Index Compression method .................36 Count..........................................48 Drop frame .................................50 External microphone ..................40 File size ......................................37 Frame rate..................................36 Grid display ................................51 Information display .....................26 Manual exposure shooting .........23 Metering timer ............................52 Microphone.................................
MEMO C Y P O 99
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. http://pro.usa.canon.com http://pro.usa.canon.com/support (855) CINE-EOS (855-246-3367) (USA only) CANADA CANON CANADA INC. http://www.canon.ca/pro Professional Product Support / Soutien des produits professionnels (800) 667-2666 EUROPE, AFRICA & MIDDLE EAST CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands CANON FRANCE S.A.S.
