REVISION 0 Apr. 2000 QY8-1370-000 COPYRIGHT 2000 CANON INC. CANON BJC-6200 0400 AB 0.
042000 AB 0.
Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality. Corrections This manual could include technical inaccuracies or typographical errors due to improvements or changes in the products.
I. ABOUT THIS MANUAL This manual consists of three parts containing information for servicing the product. Product Specifications Part 1: Product Specifications Product overview and specifications. Disassembly and reassembly procedures are not fully covered in this manual. Refer to the separate Parts Catalog instead. I Appendix Part 3: Appendix Block diagrams, information on the hardware technologies, and pin configurations.
II. TABLE OF CONTENTS Page 1- 1 1- 1 1- 2 1- 2 1- 2 1- 2 1- 3 1- 3 1- 3 1- 4 1- 4 1- 5 1- 5 1- 6 1- 7 1- 8 Part 1: PRODUCT SPECIFICATIONS 1. PRODUCT OUTLINE 1.1 Product Outline 2. SPECIFICATIONS 2.1 Printer Specifications 2.1.1 Printer specifications 2.1.2 Printer service life 2.2 Paper Specifications 2.2.1 Paper sizes and weights 2.2.2 Paper types and handling 2.2.3 Printable area 2.3 BJ Cartridge Specifications 2.4 Optional Scanner Cartridge Specifications 2.4.1 Scannable area 2.
Page 2 -23 2 -23 2 -24 2 -24 2 -25 2 -25 2 -25 2 -25 2 -26 2 -26 2 -26 2 -27 2 -28 2 -28 2 -29 2 -30 2 -31 2 -31 2 -31 2 -31 2 -31 4. OPERATION CHECK AFTER DISASSEMBLY AND REASSEMBLY 4.1 Check Procedure 5. TRANSPORTING THE PRINTER 5.1 Preparation for Transport 6. PARTS REPLACEMENT, PERIODIC INSPECTIONS, & TOOLS 6.1 Parts Replacement 6.2 Periodic Inspections 6.3 Tool List 6.4 Operation with the Printer's Operation Panel 6.4.1 Cleaning 6.4.2 Printing the nozzle check pattern 6.4.3 Roller cleaning 7.
III.
IV.
Part 1 PRODUCT SPECIFICATIONS Page 1- 1 1- 1 1- 2 1- 2 1- 3 1- 4 1- 5 1- 6 1- 7 1- 8 1. PRODUCT OUTLINE 1.1 Product Outline 2. SPECIFICATIONS 2.1 Printer Specifications 2.2 Paper Specifications 2.3 BJ Cartridge Specifications 2.4 Optional Scanner Cartridge Specifications 2.5 Printer and Scanner Drivers 3. PACKING CONFIGURATION 4.
Part 1: Product Specifications BJC-6200 1. PRODUCT OUTLINE 1.
Part 1: Product Specifications BJC-6200 2. SPECIFICATIONS 2.1 Printer Specifications 2.1.1 Printer specifications Type Paper Feed System Resolution Throughput (Reference only) Printing Direction Max. Printing Width Interface ASF Capacity Sensors Operating Noise Ambient Conditions Power Source External Dimensions Required Space Weight Standard Conformance Desktop serial printer Automatic feed only (No manual feed) 1440 × 720 dpi (Max.
Part 1: Product Specifications BJC-6200 2.2 Paper Specifications 2.2.1 Paper sizes and weights 2.2.2 Paper types and handling Type Plain paper Plain paper for Color BJ High-quality paper Photo glossy paper Glossy film Transparency film Back print film Banner T-shirt transfer Photo glossy card Postcard Envelope LC-301* Size A4/B5/LTR/LGL/ A5 (Portrait/ Landscape) A4/LTR ASF Capacity Paper Thickness Lever Position Approx. 10 mm or less Up (Approx. 100 sheets of 64 g weight) Approx.
Part 1: Product Specifications BJC-6200 2.2.3 Printable area A4/A5/B5/Letter (LTR)/Legal (LGL)/ 3.0mm Envelope 3.0mm 32mm 5.0mm 6.4mm (COM#10: 31.4mm) (DL size: 10.4mm) (2) 26mm (1) 23mm 5.0mm 3.4mm: A4/A5/B5 6.4mm: LTR/ LGL 3.4mm: A4/A5/B5 6.3mm: LTR/ LGL Banner Paper 3mm 3.4mm 1 2 3 4 5 6 3.4mm Max. 6 sheets printable. After printing, the seventh sheet is cut off. 32mm : Recommended printing area : Printable area (1) For monochrome printing. (2) For color or photo-quality printing.
Part 1: Product Specifications BJC-6200 2.4 Optional Scanner Cartridge Specifications IS-32 Cartridge replacement type color scanner 90 × 90, 180 × 180, 200 × 180, 300 × 360, 360 × 360, 720 × 720 256-pixel, linear (single line) CCD RGB (Red, Green, Blue) RGB-switching progressive scanning Document inserted in scanning holder and fed via the ASF ECP/Nibble Approx. 41 mm (W) × 90 mm (D) × 77 mm (H) Approx. 100 g Printer setting for scanning: Paper thickness lever must be up.
Part 1: Product Specifications BJC-6200 2.5 Printer and Scanner Drivers The drivers and interface ports that can be used with the printer are listed below. Windows 95/98 Windows NT4.0 Windows 2000 Macintosh Printer Driver Parallel I/F USB I/F ● ▲* ● ✕ ● ●* --●** Scanner Driver Parallel I/F USB I/F ●*** ▲* ●*** ✕ ●*** ●* --●** ●: * ** Compatible. ▲: Conditionally compatible. ✕: Incompatible. For USB, compatibility is assured only with personal computers with Windows 98/2000 preinstalled.
Part 1: Product Specifications BJC-6200 3. PACKING CONFIGURATION After opening the package, make sure all the items below have been included.
Part 1: Product Specifications BJC-6200 4. PARTS CODE LIST A list of printer parts, consumables, and optional equipment are listed below.
Part 2 TROUBLESHOOTING Page 2- 1 2- 1 2- 2 2- 2 2- 3 2- 6 2- 7 2 -10 2 -10 2 -11 2 -13 2 -17 2 -23 2 -23 2 -24 2 -24 2 -25 2 -25 2 -25 2 -25 2 -26 2 -28 2 -28 2 -29 2 -30 2 -31 2 -31 2 -31 2 -31 2 -31 1. PRINTER OPERATION 1.1 Status Indicator 2. SERVICING 2.1 Before Troubleshooting 2.2 Detectable Problems from System Start to Exit 2.3 Troubleshooting Problems 2.4 Troubleshooting With Error Indications 3. DISASSEMBLY AND REASSEMBLY 3.1 Cautions for Disassembly and Reassembly 3.2 Exploded View 3.
Part 2: Troubleshooting BJC-6200 1. PRINTER OPERATION The printer's operation status is indicated by the status indicator, and the printer can be controlled from the computer or with the printer itself. 1.1 Status Indicator The printer's operation status is indicated by the indicator. When an error occurs, the nature of the error can be known by the number of times the indicator blinks in orange and/or green. Indicator Figure 2-1 Operation Panel 1.1.
Part 2: Troubleshooting BJC-6200 2. SERVICING 2.1 Before Troubleshooting Before troubleshooting the printer, check the following and see if any of the applicable problems can be fixed. Problem The printer does not operate at all Paper feeding does not work No printing Stripes appear in the printing Probable Cause The power outlet is not supplying the required voltage. The power cord is not properly connected to the printer or power outlet. The power switch is not ON.
Part 2: Troubleshooting BJC-6200 2.
Part 2: Troubleshooting BJC-6200 From preceding page Error check Normal? No • Indicator repeats: Blinks 3 times in Yes Diode sensor check Normal? orange/green, then one long blink in green. (See page 2-8) • Indicator repeats: Blinks once in orange, repeatedly. ROM error* (See page 2-8) • Indicator repeats: Blinks 2 times in RAM error* orange, repeatedly. (See page 2-8) • Indicator repeats: Blinks 6 times in Waste ink-full error orange/green, followed by a long blink in green, repeatedly.
Part 2: Troubleshooting BJC-6200 From preceding page ASF sensor check Normal (ON)? No Yes ASF sensor error BJ cartridge check • Indicator repeats: Blinks 10 times in No Normal? Yes Cleaning • Cartridge installation • Cartridge not recognized • Not installed properly Cover open check Open/ Closed? Closed The sensor will determine if the front cover is open or closed.
Part 2: Troubleshooting BJC-6200 2.3 Troubleshooting Problems Problem Power does not come on No printing White stripes or smearing appear Soiled paper Spur tracks appear Broken vertical lines Error does not occur at ink-out Abnormal noise Probable Cause / Check Items AC adapter, control board, DC cable. BJ cartridge, purge unit, ink tank, or orange cap/tape still affixed to print head. BJ cartridge, faulty BJ cartridge contacts, cartridge ribbon cable, purge unit, control board, ink tank.
Part 2: Troubleshooting BJC-6200 2.4 Troubleshooting With Error Indications 1) Error indication when a user-recoverable error occurs The indicator indicates an error by blinking in orange for a certain number of times. After it blinks in orange to indicate the error, it blinks once, long, in green. This indication is repeated. 2) Error indication when an error un-recoverable by the user occurs The indicator indicates an error by blinking alternately in orange and green for a certain number of times.
Part 2: Troubleshooting BJC-6200 8 times in orange --- Waste-ink warning** 9 times in orange --- Auto Print Position Adjustment 1 Cause: The total waste-ink count recorded in the EEPROM exceeds 95% of the stipulated amount indicating waste-ink full. Suspect: Waste-ink absorber, control board Cause: Auto head position adjustment problem occurred.
Part 2: Troubleshooting BJC-6200 5200 Print head temperature sensor (diode sensor) error 9 times in orange/green 5600 No cartridge error 10 times in orange/green 5700 ASF sensor error 11 times in orange/green 12 times in orange/green 5210 Scanner cartridge error 5000 Recovery system error --- Ink sensor Internal Error No error indication Cause: Faulty temperature sensor in the BJ cartridge.
Part 2: Troubleshooting BJC-6200 3. DISASSEMBLY AND REASSEMBLY 3.1 Cautions for Disassembly and Reassembly 3.1.1 Ink stains (Ink path/ink mist) During servicing, be careful not to touch the ink path and get ink stains on the printer, work table, and your hands and clothing. The ink path includes the BJ cartridge's ink tank supply inlet, the BJ cartridge's ink filter, the ink nozzles and maintenance jet receptacle, head cap, wiper, and waste-ink absorber.
Figure 2-2 Exploded View Troubleshooting 3.
Part 2: Troubleshooting BJC-6200 3.3 Disassembly and Reassembly Cautions for disassembling and reassembling the printer are stated below. As for the disassembly procedure, refer to the Parts Catalog. The illustrations in the Parts Catalog are numbered according to the order of disassembly. 3.3.1 Carriage lock release Normally, when a cartridge is installed on the carriage and the power is turned off, the printer moves the carriage to the capping position to lock it.
Part 2: Troubleshooting BJC-6200 3.3.3 Removing the upper cover unit To remove the upper cover unit, see the figure below. 1) Unhook the upper cover unit's four hooks on the sides and back. 2) Unhook the two hooks on the front. To reinstall, follow this procedure in reverse. Figure 2-4 Upper Cover Unit Removal and Installation 3.3.4 Removing the printer unit Remove the printer unit as shown in the figure below. 1) First remove the two screws securing the printer unit and bottom case.
Part 2: Troubleshooting BJC-6200 3.3.5 Removing the pressure roller unit To remove the pressure roller unit, release the three hooks in turn as shown by the arrows in the figure. Then pull it out from rear of the printer unit. When releasing the hooks, start with the one on the left (when facing the front of the pressure roller unit). This will make removal easier. Troubleshooting Figure 2-6 Removing the Pressure Roller Unit 3.3.
Part 2: Troubleshooting BJC-6200 3.3.7 Removing the ASF unit Set screw ASF unit Set screw Figure 2-8 Removing the ASF Unit 3.3.8 Removing the head gap adjustment section Secured to the printer frame, the head gap adjustment plate is for adjusting the gap between the BJ cartridge's nozzles and platen so that the optimum printing quality is obtained. If the set screw securing the head gap adjustment plate to the printer frame is loosened, the head gap will change and head gap adjustment will be necessary.
Part 2: Troubleshooting BJC-6200 3.4 Adjustments and Settings After Disassembly and Reassembly 3.4.1 Adjustments (1) User Level Adjustment BJ cartridge printing position adjustment Timing After BJ cartridge installation/removal Time Required Tools Required 2 min. 2 sheets of B5 or larger paper (2) Serviceman Level Adjustment Belt tension Time Required Tools Required 1 min. Tension spring (QY9-0043) 1 min. None EEPROM setting BJ cartridge printing position adjustment 2 min.
Part 2: Troubleshooting BJC-6200 3.4.2 Applying grease Apply the correct grease to the places shown below. Use a flat brush to spread a thin coat of grease. To disassemble and reassemble the printer, refer to the Parts Catalog. When applying grease, be careful not to get any grease on the wiper and cap. Cam friction surface Approx. 27 mg (Molykote PG-641) Pick-up roller friction surface Approx.
Part 2: Troubleshooting BJC-6200 3.4.3 Print head position adjustment Since the printer has two BJ cartridges installed, the ejected ink's placement can be thrown off due to the differences in the BJ cartridges and the installation conditions. Less than optimum printing quality will result. To eliminate this misalignment, perform the auto print head position adjustment with the printer driver's utility after installing the BJ cartridges.
Part 2: Troubleshooting BJC-6200 3.4.4 Setting the EEPROM After replacing the control board or waste-ink absorber, reset the EEPROM, set the model settings, and do a test printout to confirm the settings. The EEPROM (IC502) on the control board stores various printer data such as the waste-ink amount and other printer specific settings. The procedure is described in 7.1 Service Mode Operations on page 2-28.
Part 2: Troubleshooting BJC-6200 3.4.6 Adjusting the head gap If the set screws securing the head gap adjustment plate to the printer frame are loosened or removed, the head gap adjustment will be necessary. Preparation 1) Remove the upper cover unit and bottom case. (Or, reassemble the printer so that the upper cover unit and bottom case are to be attached next.) 2) Remove the paper thickness lever spring and the left and right shaft clips, then attach the bottom case.
Part 2: Troubleshooting BJC-6200 Adjustment Procedure 1) Set the gap gauge (QY9-0038) to position A1. 2) Move the carriage belt by hand so that the carriage goes to position A2. Align the bottom case's rib with the carriage's right end. 3) Install a black BJ cartridge without ink tank in the carriage. 4) Move the paper thickness lever up and down two or three times, then, while holding the lever in the normal paper (up) position, tighten the red set screw on the right end.
Part 2: Troubleshooting BJC-6200 4. OPERATION CHECK AFTER DISASSEMBLY AND REASSEMBLY 4.1 Check Procedure After disassembly and reassembly, follow the procedure below to check the printer's operation. 1) After service/factory test printout with the printer alone Check that the printer can print properly. The procedure is described in 7.1 Service Mode Operations on page 2-28. After replacing the control board or the ink absorber, the following check procedure is also necessary in addition to 1) above.
Part 2: Troubleshooting BJC-6200 5. TRANSPORTING THE PRINTER Before moving or transporting the printer, put one BJ cartridge (with the ink tank installed) in the cartridge container. This is to prevent the ink from leaking and the BJ cartridge's ink nozzles from drying up. Before returning the repaired printer back to the customer, move the carriage to the cartridge replacement position and tape it at that position. 5.1 Preparation for Transport When transporting the printer, follow the procedure below.
Part 2: Troubleshooting BJC-6200 6. PARTS REPLACEMENT, PERIODIC INSPECTIONS, & TOOLS 6.1 Parts Replacement Level User Serviceman Level User Consumables Black BJ cartridge: BC-30 Color BJ cartridge: BC-31 Photo BJ cartridge: BC-32 Black BJ cartridge ink tank (Black: BCI-3BK) Color BJ cartridge ink tank (Black: BCI-3BK, Cyan: BCI-3C, Magenta: BCI-3M, Yellow: BCI-3Y) Photo BJ cartridge ink tank (Black: BCI-3BK Photo, Cyan: BCI-3C Photo, Magenta: BCI-3M Photo) None 6.
Part 2: Troubleshooting BJC-6200 6.4 Operation with the Printer's Operation Panel The printer can be operated in the offline operation mode, with the power turned on and without connection to a computer. With the printer turned on, you can start various printer operations by holding down the RESUME button and releasing after the green indicator blinks the stipulated number of times.
Part 2: Troubleshooting BJC-6200 Black BJ cartridge Color BJ cartridge Large-dot printing by the 1st nozzle Large-dot printing Large-dot printing by the 1st nozzle Black Yellow 48 nozzles Cyan 48 nozzles Magenta 48 nozzles 160 nozzles Large-dot printing by the 48th nozzle Large-dot printing by the 160th nozzle Small-dot printing Small-dot printing by the 1st nozzle Small-dot printing by the 1st nozzle Small-dot printing by the 160th nozzle (Y) 180 dpi horizontal position forward direction (
Part 2: Troubleshooting BJC-6200 7. SERVICE-RELATED FEATURES The printer has a Service Mode for accessing service settings and executing test printouts. The operations can be selected via the operation panel buttons. 7.1 Service Mode Operations 1) With the printer turned off, hold down the RESUME button and press and hold the POWER button (the green indicator lights). 2) While holding down POWER button, release the RESUME button and then press the RESUME button twice in succession.
Part 2: Troubleshooting BJC-6200 7.2 Service/Factory Test Printout The header of the service/factory test printout shows the control ROM version, model setting, total printed sheet count, total waste-ink absorption amount, and other information. Total printed sheet count with photo/color BJ cartridge Installed cartridges Model designation ROM version Total printed sheet count with black/color BJ cartridge Unused Unused Total passed sheet count with scanner cartridge ROM Ver Vx.
Part 2: Troubleshooting BJC-6200 7.3 Printing the EEPROM Information The EEPROM stores information such as the various settings; the total printed sheet count of the black, color, and photo BJ cartridges and scanner cartridge; the total waste-ink absorption amount; and the error history of the last three non user-recoverable errors. The information stored in the EEPROM is printed in the hexadecimal dump format in the EEPROM information printout.
Part 2: Troubleshooting BJC-6200 7.4 Resetting the EEPROM The EEPROM stores information such as the various settings; the total printed sheet count of the black, color, and photo BJ cartridges and scanner cartridge; the total waste-ink absorption amount; and the error history of the last three non user-recoverable errors. The printer uses the total waste-ink absorption amount recorded by the EEPROM as the basis for determining whether the waste ink is full.
Part 2: Troubleshooting BJC-6200 This page intentionally left blank 2-32
Part 3 APPENDIX Page 3- 1 3- 1 3- 2 3- 2 3- 3 3- 4 3- 5 3- 6 3 -10 3 -11 3 -12 3 -13 3 -13 3 -14 3 -14 3 -14 3 -15 3 -15 3 -15 3 -17 1. TECHNICAL REFERENCE 1.1 Print Mode List 1.2 Purge Unit's Capping and Cleaning Functions 1.3 Cautions About the Inks 1.4 Operation with a Computer 1.5 Detection Functions by Sensors 1.6 Electronic Circuit Description 2. CONNECTOR LOCATIONS AND PIN CONFIGURATIONS 2.1 Carriage Board 2.2 BJ Cartridge 2.3 Scanner Cartridge (Optional) 2.4 AC Adapter 2.5 DC Power Cable 2.
Part 3: Appendix BJC-6200 1. TECHNICAL REFERENCE 1.1 Print Mode List The print mode list for the black, color, and photo BJ cartridges is shown below. By setting the printer driver's "Dithering," "Paper Type," and "Printing Quality" settings, the printer will operate in the printing modes below.
Part 3: Appendix BJC-6200 1.2 Purge Unit's Capping and Cleaning Functions Capping is executed at the following times: • When the power is turned off with the POWER button. • When uncapped and print signals have not been received within the stipulated time during standby. During paper feeding: After 20 min. Other times: After 30 sec. • After the front cover has been left open for 10 minutes. Cleaning is executed at the times listed in the table below.
Part 3: Appendix BJC-6200 1.4 Operation with a Computer You can set the printer's functions via the dedicated printer driver. 1.4.
Part 3: Appendix BJC-6200 1.5 Detection Functions by Sensors The printer has the following sensors to detect the printer's operating status.
Part 3: Appendix BJC-6200 1.6 Electronic Circuit Description 1.6.1 Circuit block diagram A block diagram of the printer's electronic circuit comprising the control board and carriage board is shown below.
Part 3: Appendix BJC-6200 2.
Part 3: Appendix BJC-6200 CN304 (Parallel Interface Connector) Compatible Mode STROBE DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 ACKNLG BUSY P.E. SELECT AUTO FEED XT N.C. GND GND +5.0V STROBE-RET (GND) DATA1-RET (GND) DATA2-RET (GND) DATA3-RET (GND) DATA4-RET (GND) DATA5-RET (GND) DATA6-RET (GND) DATA7-RET (GND) DATA8-RET (GND) ACKNLG-RET (GND) BUSY-RET (GND) P.E.-RET (GND) INIT ERROR GND N.C +5.
Part 3: Appendix BJC-6200 CN401 (Ink Sensor Connector) Pin No. 1 2 3 Signal INK_PWM ... INKS IN/OUT OUT ... IN Function Photo LED drive signal in the ink sensor GND Voltage varying according to the reflected light amount CN402 (Pump Sensor Connector) Pin No. 1 2 3 Signal VSEN ... SNS_DO_RUCK IN/OUT OUT ... IN Function Photo LED drive signal in the ink sensor GND Pump sensor sense signal High (sense)/Low CN501 (DC Power Source Connector) Pin No. 1 2 3 4 Signal +24V HGND +5-GND +5V IN/OUT IN ... .
Part 3: Appendix BJC-6200 CN202 (Carriage Ribbon Cable Connector) ↔ CN2: Carriage Board Signal IN/OUT Function DIR OUT Serial data I/O direction control signal HENB3 OUT Front heater driving signal for nozzles 113-160 in the head HENB2 OUT Rear heater driving signal for nozzles 113-160 in the head HENB1 OUT Front heater driving signal for nozzles 1-112 in the head HENB0 OUT Rear heater driving signal for nozzles 1-112 in the head BENB1* OUT Heater enable decoder's output signal-generation signal BENB0* OUT
Part 3: Appendix BJC-6200 2.1 Carriage Board 4 CN4 32 34 2 31 1 1 1 CN5 33 CN3 18 32 34 31 3 33 1 CN1 27 CN6 4 3 4 1 CN2 27 1 2 Figure 3-7 Carriage Board CN1 (Carriage Ribbon Cable Connector) See page 3-8 (CN201 Carriage Ribbon Cable Connector). CN2 (Carriage Ribbon Cable Connector) See page 3-9 (CN202 Carriage Ribbon Cable Connector). CN3 (Carriage Ribbon Cable Connector) See page 3-9 (CN203 Carriage Ribbon Cable Connector). CN4/CN5 (Left/Right Cartridge) Pin No.
Part 3: Appendix BJC-6200 2.2 BJ Cartridge 32 28 24 20 16 12 8 30 26 22 18 14 10 31 27 23 19 15 11 29 25 21 17 13 9 4 6 7 2 3 5 1 Figure 3-8 BJ Cartridge Signal HVH SUBH0/1 VHG HDATA0/1 IN/OUT OUT OUT ...
Part 3: Appendix BJC-6200 2.3 Scanner Cartridge (Optional) 32 28 24 20 16 12 8 30 26 22 18 14 10 31 27 23 19 15 11 29 25 21 17 13 9 4 6 7 2 3 5 1 Figure 3-9 Scanner Cartridge Pin No. 1, 2, 3 4 5 6 7, 8 9 10 11 12 13 14 15 16 17 18 19 20, 21, 22 23 24 25 26, 27, 28 29 30 31 32 Signal VHLED N.C. GNDLED N.C. GNDLED DT0 GNDLED RWR VDD DTCK VSS REN VSS RDT SCHKR LNST N.C. DT1 DT2 DT3 N.C. RST DIA DIK ... IN/OUT IN ... ... ... ... IN/OUT ... IN IN IN/OUT ... IN ...
Part 3: Appendix BJC-6200 2.4 AC Adapter 13 57 2 68 Figure 3-10 AC Adapter Signal ... ... +24V ... +5V +5-GND ... HGND IN/OUT ... ... ... ... OUT ... ... ... Function N.C. N.C. +24V DC N.C. +5V DC GND N.C. GND Appendix Pin No. 1 2 3 4 5 6 7 8 2.5 DC Power 1 3 5 4 1 5 Figure 3-11 DC Power Cable Pin No. 1 2 3 4 5 Signal +24V ... HGND +5V-GND +5V IN/OUT OUT ... ... ...
Part 3: Appendix BJC-6200 2.6 DC Carriage Motor 1 4 Figure 3-12 Carriage Motor Pin No. 1 2 3 4 Signal CRA CRB CRA CRB IN/OUT IN IN IN IN Function Carriage motor phase A Carriage motor phase B Carriage motor phase A Carriage motor phase B 2.7 Paper Feed Motor 1 4 Figure 3-13 Paper Feed Motor Pin No. 1 2 3 4 Signal LFA LFB LFA LFB IN/OUT IN IN IN IN Function Paper-feed motor phase A Paper-feed motor phase B Paper-feed motor phase A Paper-feed motor phase B 2.
Part 3: Appendix BJC-6200 2.9 Ink Sensor 3 1 1 3 3 1 Figure 3-15 Ink Sensor Pin No. 1 2 3 Signal INK/PWM ... INKS IN/OUT IN ... OUT Function Photo LED drive voltage in the ink sensor GND Voltage varying according to the reflected light amount 2.10 Printing Position Sensor 1 Appendix 4 Figure 3-16 Print Position Sensor Pin No. 1 2 3 4 Signal REGA SNSG REGC LGND IN/OUT OUT ... OUT ...
Part 3: Appendix BJC-6200 This page intentionally left blank 3-16
Part 3: Appendix BJC-6200 2.
Part 3: Appendix BJC-6200 7 6 5 4 3 2 1 LOGIC BOARD 01 <01-F1> R101 1 7 +3.3R 2 5 8 R123 0,1A 2 1 1 1U,10V ROMA15 ROMA2 ROMA14 ROMA3 ROMA13 ROMA4 ROMA12 ROMA5 ROMA11 ROMA6 ROMA10 ROMA7 ROMA9 5VDD3 103 161 XT2 ROM_A20 100 check 13 ROMD0 14 ROMD8 15 ROMD1 16 ROMD9 17 ROMD2 18 ROMD10 19 ROMD3 20 ROMD11 A1 A15 A0 A16 CE _BYTE/VPP GND1 GND2 OE D15/A1-1 D0 D7 D8 D14 D1 D6 D9 D13 D2 D5 D10 D12 D3 D4 D11 VDD 35 34 33 ROMA10 +3.
Part 3: Appendix BJC-6200 8 7 6 5 3 IC201 LA6324NML +5V HEADCONT1 1K HEADCONT3 8 11 1 RA201 100K HEADCONT4 FB203 +5V RA201 3 7 RA202 3 5 33K +5V HEADCONT5 BK32164S601 RA201 6 2 HEADCONT6 RA202 6 180K 7.
Part 3: Appendix BJC-6200 8 7 6 5 4 3 2 1 LOGIC BOARD 03 VIF <04-D4> F RA303 3.3K,0.063W IFD[7:0] CA301 NFA3216G2C100R6R8 IFD1 3 RA301 0.
Part 3: Appendix BJC-6200 8 7 6 5 4 3 2 1 LOGIC BOARD 04 +5V +3.3V TH401 1 <01-F4> R407 2 1 INK_PWM 3 Q404 2 47K,0.063W FP1L3N TBPS1473J475H5Q 2 1 SKHVLH R412 SKQNLA DOOR 1 SKQNLA RESUME R413 1 2 FB 2 1 BK1608HS121 150,1/4W <01-F3> 1 CN401 2 CN401 3 CN401 J3P FB404 C408 1 1 2 1 POWER 2 DOOR C403 <01-F4> SKQNLA 1 2SW403 SKHVLH 2 SKQNLA 1 2SW402 C402 1 RESUME_SW C401 POW_SW <01-F4> 2 2SW401 <01-F4> 68K,1/16W F +3.3V THERMO 2 1 0.
Part 3: Appendix BJC-6200 8 7 6 5 4 3 2 1 LOGIC BOARD 05 +5V FB501 FBMH3216HM501NT 1 2 FB J4P 2 RESETX C531 3 1000P,50V 1000P,50V by IC501 <01-F6> 1 2 1 FB502 FBMH3216HM501NT C530 2 2 1 R502 2 FB 1 MM1478FFBE 1 5 2 2 VOUT 5 2 J4P R531 0,1A R530 0,1A C503 47U,35V 2 4 VIN 2 CN501 N.C 6 1 3 CONT ZD501 1K,1/16W 2 RESETX GND 7 2 CD 8 1 J4P HGND F +3.3V 1 N.C.
The printing paper contains 100% waste paper. PRINTED IN JAPAN (IMPRIME AU JAPON) CANON INC.
