Öppna förpackningen Snabbguide (den här handboken) Denna handbok innehåller en beskrivning av en rad procedurer – från öppning av förpackningen till användning av skannern. LÄS DENNA HANDBOK FÖRST! Skanningshandbok (handbok i HTML-format) Läs denna handbok när du har installerat skannern enligt anvisningarna i Snabbguide. Handboken beskriver hur du använder skannern tillsammans med den medföljande programvaran och hur du löser problem när de uppstår.
Skanner och tillbehör CanoScan 3000F CanoScan 3000 USB gränssnittskabel AC-adapter Filmguide för CanoScan 3000F (för filmremsa eller dia) Dokument och programvaror • Snabbguide (denna handbok) • Ytterligare dokument • CanoScan Setup Utility-CD-ROM [installations-CD] • Det krävs cirka 229 MB ledigt hårddiskutrymmet för att installera alla program. Ytterligare ledigt diskutrymme krävs för att köra programmen.
• I Windows XP/2000 ska du logga in med administratörsbehörighet när du installerar eller avinstallerar programvara. 1 Starta datorn. Klicka på [Cancel/Avbryt] om guiden ”Found New Hardware Wizard” [Hittade ny maskinvara] eller ”Add New Hardware” [Lägg till ny maskinvara] visas. 2 Sätt in CD-skivan CanoScan Setup Utility i CD-enheten. När du har valt språk visas huvudmenyn för CanoScan Setup Utility. 3 Klicka på [Install the Software/Installera programmet]. Läs Användarlicensavtalet för programvaran.
• Lås upp skannern innan du ansluter den till datorn. Om den lämnas låst kan det medföra fel eller andra problem. Bilder till CanoScan 3000F visas när tillvägagångssättet är lika för både CanoScan 3000F and CanoScan 3000 modellerna. 1 Ta av skannerns förseglingar. 2 Vänd skannern försiktigt. 3 För låsreglaget till märket för upplåst läge ( Låsreglage ). Märke, upplåst läge 4 Sätt tillbaka skannern i vågrätt läge.
• Kontrollera att skannern är upplåst. (s. 5) 1 Ta av skannerns förseglingar. 2 Anslut skannern till datorn med den medföljande USB-gränssnittskabeln. Bred platt kontakt USB gränssnittskabel Liten fyrkantig kontakt 3 Anslut AC-adaptern till skannern. AC-adapter • Använd bara den USB-kabel och den AC-adapter som medföljer skannern. Om du använder andra kablar eller adaptrar kan detta orsaka fel. • Skannern har ingen till/från-knapp. Spänningsmatningen aktiveras så snart som datorn startas.
Följande steg förklarar hur man skannar in bilder med ArcSoft PhotoStudio. 1 Lägg ett foto eller en bild på glaset. Lägg den övre kanten vid riktmärket. Stäng dokumentlocket. Överkant Nederkant Riktmärke 2 Välj [Start/Starta], [Programs/Program] eller [All programs/Alla program], [ArcSoft PhotoStudio 5] och [PhotoStudio 5]. PhotoStudio startar. 3 Klicka på ikonen Acquire [Hämta] på verktygsmenyn, eller gå till menyn [File/Arkiv] och välj [Acquire/Hämta]. ScanGear CS startar.
Om ett felmeddelande visas, klicka på menyn [File/Arkiv], välj [Select Source/Välj källa], välj din skannermodell och klicka på knappen [Select/Välj]. 4 För CanoScan 3000F, under [Image Source/Bildkälla] 5 väljer du [Platen/Glasplatta]. (För CanoScan 3000, kan bara [Platen/Glasplatta] väljas.) Välj [Type of original/Originaltyp]. Du kan välja ”Photo” [Foto], ”Magazine” [Tidskrift], ”Newspaper” [Dagstidning] eller ”Document” [Dokument].
8 Klicka på eller (stäng dialogruta) i ScanGear CSfönstret när du vill stänga det. Den skannade bilden visas nu i PhotoStudio-fönstret. 9 Spara den skannade bilden. Klicka på menyn [File/Arkiv] och välj [Save As/Spara som]. Ange den mapp där du vill spara bildfilen, skriv in filnamn, välj filtyp (JPG rekommenderas) och klicka sedan på [Save/Spara]. 10 Klicka på (stäng dialogrutan) i PhotoStudio när du vill stänga fönstret.
Du kan använda de tre bekvämt placerade knapparna på skannerns framsida för att enkelt kunna skanna och utföra tillhörande uppgifter – helt enkelt genom att trycka på knappen. Lägg en bild på skannern innan du trycker på en knapp. • Om du vill använda dessa knappar måste ScanGear CS, CanonScan Toolbox och ArcSoft PhotoBase vara installerade från CD-skivan CanoScan Setup Utility CD-ROM. SCAN COPY Knappen SCAN Öppna den inskannade bilden i PhotoBase-fönstret: 1 Tryck på knappen SCAN [SKANNA].
Du kan skanna 35 mm film (en ram eller dia åt gången) med CanoScan 3000F. Placera filmen 1 Avlägsna skyddsarket från dokumentlocket. Dra skyddsarket uppåt för att avlägsna det. När du har slutfört skanningen, sätt tillbaka skyddsarket genom att passa in det i hålen i dokumentlocket och skjuta det nedåt i läge. • Förvara skyddsarket på en säker plats så att det inte böjs eller bryts. • Återställ alltid skyddsarket när du inte skannar film för att förhindra att ljuskällesektionen repas.
4 Fäst filmhållaren i spåret till filmstyrningen för 35 mm film. Filmhållare Vid arbete med dia behöver inte filmhållaren vara stängd. 5 Placera den laddade filmhållaren i rätt läge på dokumentglaset. Kalibreringsspår Rikta in filmhållarens med skannerns märke längs märke. • Filmhållaren har ett kalibreringsspår som skannern använder för att beräkna färgbalansen. Filmen kan inte skannas med rätt färgbalans om spåret är igensatt. Håll det öppet. 6 Stäng dokumentlocket.
Skanning av film Följande steg förklarar hur man skannar in bilder med ArcSoft PhotoStudio. 1 Välj [Start/Starta], [Programs/Program] eller [All programs/Alla program], [ArcSoft PhotoStudio 5] och [PhotoStudio 5]. 2 Klicka på ikonen Acquire [Hämta] på verktygsmenyn, eller gå till menyn [File/Arkiv] och välj [Acquire/Hämta]. ScanGear CS startar. Om ett felmeddelande visas, klicka på menyn [File/Arkiv], välj [Select Source/Välj källa], välj din skannermodell och klicka på knappen [Select/Välj].
Den skannade bilden visas nu i PhotoStudio-fönstret. 7 Spara den skannade bilden. Klicka på menyn [File/Arkiv] och välj [Save As/Spara som]. Ange den mapp där du vill spara bildfilen, skriv in filnamn, välj filtyp (JPG rekommenderas) och klicka sedan på [Save/Spara]. 8 Klicka på (stäng dialogrutan) i PhotoStudio när du vill stänga fönstret. • Om skannern inte fungerar som det beskrivs ovan läser du avsnittet om ”Felsökning” i Skanningshandbok (HTML-format).
CanoScan 3000F Skannertyp Skannerelement Ljuskälla Optisk upplösning Valbar upplösning Färg Gråskala Färg Skanningshastighet*1 Gråskala / (Foto eller Dokument) Svartvit Skanningshastighet*1 Färg / Gråskala / (Film) Svartvit Förhandsgranskningshastighet*2 Skanningsbitdjup Gränssnitt Maximalt dokumentformat Filmtyp/antal bilder Skannerknappar Temperatur Driftområde Strömkrav Strömförbrukning Maximala yttermått Vikt Luftfuktighet CanoScan 3000 Flatbädd Färgdisplay med 6 linjer Fluorescerande lampa med kal
Denna blankett ska användas för att anteckna driftmiljön för den inköpta skannern. Vid eventuella problem med skannern behöver du denna information när du kontaktar vår kundsupport. Anteckna informationen och förvara den på en säker plats. • Informationen krävs också vid garantireparationer. Se till att du har antecknat informationen och att du förvarar den på en säker plats. • Service av denna utrustning ges som längst fem år efter att tillverkningen har upphört.