Quick Start Guide Please read this guide before operating this scanner. After you finish reading this guide, store it in a safe place for future reference. Table of Contents Safety Precautions.............................. 1 Using the Scanner Buttons ................. 10 Package Contents............................... 3 Scanning with MP Navigator EX......... 11 Installing the Software......................... 4 Scanning Film ..................................... 12 Preparing the Scanner ..............
FCC Notice (U.S.A. Only) For 120V, 60Hz model Model Number : K10346 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety Precautions Safety Precautions Please read and take note of the following precautions before using the scanner and accessories. WARNING Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. In order to use the scanner safely, always pay attention to these warnings. CAUTION Indicates a caution concerning operations that may lead to injury to persons or damage to property if not performed correctly.
Safety Precautions CAUTION • As a rule, do not use electrical extension cords. Fire or electrical shock may result. If the use of an extension cord is necessary, do not use one longer than 5 m (approximately 16.4 feet). Make sure that the extension cord is not twisted, and that the power cord is fully plugged into the extension cord. Do not use multiple extension cords. • When unplugging the power cord, always pull on the main body.
Package Contents Package Contents Scanner and Accessories Scanner USB Cable Power Cord Film Guides (for 35 mm film strip/slide) Film Guide (for 120 format film) Documentation • Quick Start Guide (this document) • Additional Documents Setup CD-ROM • Software Programs - ScanGear (scanner driver) MP Navigator EX (utility software) Solution Menu (menu panel software) ArcSoft PhotoStudio (image editing software) • On-Screen Manual (for ScanGear, MP Navigator EX, and troubleshooting) Adobe Photoshop
Installing the Software Installing the Software • Do NOT connect the scanner to a computer before installing the software. If you connect the scanner, unplug the USB cable from the computer. When the Found New Hardware screen appears, unplug the USB cable from the computer and click Cancel. The screen may close automatically when the USB cable is unplugged. • Quit all running applications before installation.
Installing the Software 4 Click Easy Install on the main menu. 5 Click Install to start installation. Carefully read the License Agreement, and then click Yes to proceed. For Macintosh, skip step 6 and go to step 7. 6 For Windows, carefully read the Please Allow All Install Wizard Processes screen, and then click Next. 7 Follow the on-screen instructions to perform the installation. 8 For users in the U.S.A.
Installing the Software 9 For Windows, when the Extended Survey Program screen appears, confirm it. If you can agree, click Agree. 10 When the installation is complete, follow the on-screen instructions. For Windows: Click Restart. After restarting the computer, Solution Menu will appear. For Macintosh: Click Exit. Solution Menu icon will be registered in the Dock. You can select either MP Navigator EX, "On-Screen Manual", or the Online Registration.
Preparing the Scanner Preparing the Scanner Unlocking the Scanner 1 2 Peel the shipping tapes off the scanner. Open the document cover and slide the scanner lock switch toward the unlock mark ( ). Unlock Mark • The document cover is locked temporarily at an angle of about 50 degrees. 3 Close the document cover. • Handle the scanner with both hands. Be careful not to drop the scanner.
Preparing the Scanner Connecting the Scanner 1 2 3 4 Connect the scanner to your computer with the supplied USB cable. Connect the supplied power cord to the scanner. Plug the power cord into the electrical outlet. Press ( ) to turn the power on. Turning the Power Off To turn the scanner off, be sure to press the ON button. Check the POWER lamp goes off, and then unplug the power cord. If you unplug the power cord while the POWER lamp is lighting or blinking, the scanning unit does not move correctly.
Try Scanning Try Scanning This section explains the basic scanning procedures using MP Navigator EX. 1 Open the document cover to make sure the protective sheet is put on. 2 Place a color photo document with the side to be scanned facing down on the platen glass at least 1 cm (0.4 in.) away from the edges of the platen glass, and then close the document cover. 3 Top protective sheet Bottom Start MP Navigator EX.
Using the Scanner Buttons Using the Scanner Buttons Scanner buttons allow you to copy, scan, e-mail, and save scanned images in PDF format with a press of a button. Simply place your document on the scanner, and then press the scanner button for the required function. For more information, see "On-Screen Manual". AUTO SCAN Button Discriminates the document type automatically, then scans and saves it with appropriate settings.
Scanning with MP Navigator EX Scanning with MP Navigator EX MP Navigator EX enables you to perform various tasks, such as compositing images, scanning with the scanner driver (ScanGear), and correcting/editing scanned images, as well as simply scanning. Starting MP Navigator EX 1 Click Scan/import photos or documents in the Solution Menu. You can also start it by following procedure. For Windows: Select Start – (All) Programs – Canon Utilities – MP Navigator EX 3.1, and click MP Navigator EX 3.1.
Scanning Film Scanning Film This scanner can scan 35 mm film (film strip or slide) and 120 format film. Follow the procedure below when scanning film. 1 Remove the protective sheet from the document cover. Press and hold the lever at the top of the protective sheet c while you pull the sheet outward and detach it d. protective sheet light source • Store the protective sheet in a safe place so that it will not get bent or broken.
Scanning Film 35 mm Slides c Align the Film Guide’s tab with the FILM symbol on the platen glass of the scanner. Calibration Slot d Place a slide or slides face down (correctly viewed from below) in the Film Guide as shown in the figure on the right. 120 Format Films c Align the Film Guide’s tab with the FILM symbol on the platen glass of the scanner, then open the Film Holder and remove the Film Retainer Sheet. Calibration Slot d e Place the film face down. Close the Film Holder.
Scanning Film Using a Film Retainer Sheet Curled film strips can stick to the platen glass and cause a pattern of rings called Newton Rings to appear on the scanned image. If this occurs, scan using the supplied Film Retainer Sheet as shown in the diagram. (A) (A) Scan with the Film Retainer Sheet inserted beneath the film.
Scanning Film 6 Click Scan. Do not move the scanner while it is operating. 7 When the preview is displayed, place a check mark beside the number(s) of the frame(s) you want to scan, and then click Scan to start scanning. Do not move the scanner while it is operating. 8 When prompted that the scanning completed, click Exit. 9 Click Save to save the images and close MP Navigator EX.
Specifications Specifications CanoScan 9000F Scanner Type Flatbed Sensor Type CCD 12-line color Light Source White LED Transparencies: 9600 x 9600 dpi Reflectives: 4800 x 4800 dpi Optical Resolution *1 Selectable Resolution 25-19200 dpi (ScanGear) Color Scanning Bit Depth Grayscale 48 bit input (16 bit input for each color (RGB)) 48 bit or 24 bit output (16 bit or 8 bit output for each color (RGB)) 48 bit input (16 bit input for each color (RGB)) 16 bit *2 or 8 bit output Hi-Speed USB *3 Interfac
Quick Start Guide Please read this guide before operating this scanner. After you finish reading this guide, store it in a safe place for future reference. Table of Contents Safety Precautions.............................. 1 Using the Scanner Buttons ................. 10 Package Contents............................... 3 Scanning with MP Navigator EX......... 11 Installing the Software......................... 4 Scanning Film ..................................... 12 Preparing the Scanner ..............
