rr e ea ad d tt h h ii ss ff ii rr ss tt Canon Color Image Scanner CanoScan FB1200S Getting Started Inspect the package contents ▼ Setting Up the scanner ▼ Installing the software ▼ Test scanning operation Guide to the software how to use the scanning software Windows ScanGear CS-S ScanGear Toolbox CS Adobe Photoshop 5.0 LE Caere OmniPage Limited Edition Macintosh Plug-in Module CS-S CanoScan Toolbox CS Adobe Photoshop 5.
How to Make Best Use of the Manuals When you open the box Printed Manual ide u is G CanoScan FB1200S Th Getting Started Describes operating procedure from set up and software installation to scanning and confirmation of operation. Please read before using the scanner for the first time. Windows Macintosh Learn advanced techniques for scanning after reading this guide and setting up the scanner.
How to Use this Guide Thank you for purchasing the CanoScan FB1200S color image scanner. This Getting Started guide explains the necessary steps to connect the scanner to your computer and begin scanning. We recommend that you carefully read this entire guide to learn the proper procedures to avoid malfunctions. Organization of the Guide The guide is divided into two main sections. • Setting Up the Scanner This section provides a step-by-step explanation of how to set up the scanner for first-time users.
Table of Contents CHAPTER 1 Setting Up the Scanner Before using this scanner for the first time, follow the procedures in this section to connect to the computer and install the software. Inspecting the Package Contents ....................................................... 5 Setting Up the Scanner ...................................................................... 6 Installing the SCSI Card ..................................................................... 7 Connecting to the Computer .............
Features of the CanoScan FB1200S This scanner is a flatbed color scanner with 1200 dpi optical resolution incorporating the following features. • Fine Color Tones and High Resolution Achieves a maximum optical resolution of 1200 dpi x 1200 dpi. The 1200 dpi primary scan (horizontally across document) is realized with VAROS, the proprietary Canon system short for VAriable Refraction Optical System.
CHAPTER 1 Setting Up the Scanner In this section, we explain the step-by-step procedures for setting up the scanner from opening the package to checking the operation of the scanner. Please follow the procedures without skipping any steps. Inspecting the Package Contents P. 5 Setting Up the Scanner Unlock the Scanning Unit P. 6 Will the Scanner be the only SCSI Device Connected to the Computer? NO YES Setting the SCSI ID and the Terminator Settings Product Guide p.
Inspecting the Package Contents After opening the box, inspect its contents. Scanner Unit and Accessories Power Cord AC Adapter Scanner Unit AVA-2902E SCSI Card Windows Platform SCSI Interface Cable Connects the scanner to a computer (Half Pitch 50-Pin, D-Sub 25-Pin) Software and Documents • CanoScan Setup Utility CD-ROM Contains the software to operate the scanner, the software manuals and reader software for the manuals.
Setting Up the Scanner Unlock the Scanning Unit The scanner is shipped with the scanning unit locked to prevent damage during transport. You must unlock it to use the scanner. ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Remove the document cover. Grasp it with both hands at the hinges and lift straight up.
Installing the SCSI Card Windows Macintosh These procedures are only required for use of the scanner with the Windows platform. What is a SCSI Card? SCSI (pronounced ‘scuzzy’) is a standard interface for connecting SCSI devices, such as scanners and hard disk drives. SCSI connectors are usually not supplied as standard equipment on computers running Windows. Accordingly, a SCSI card with a SCSI connector must be installed to connect SCSI devices together.
Windows Macintosh How to Install the SCSI Card Have a Phillips (+) screwdriver handy and follow the procedures below to install the AVA-2902E SCSI Card into your computer. ○ 1 ○ 2 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Turn off your computer and disconnect all the connected devices and cables. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Remove the computer casing.
Windows Macintosh ○ 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Gently insert the SCSI card all the way into the PCI bus slot. • Insert the SCSI card in straight, being careful not to tilt it at an angle. A reasonable amount of force is required to insert the card all the way into the slot. Ensure that you push it in until your hand meets solid resistance.
Windows Macintosh Start Windows After you have installed the SCSI card, start the Windows program. ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Turn on the computer. ▼After a few moments, the New Hardware Found message will display and the required software will automatically install. Subsequently, a new message asking you to restart the computer will display.
Windows Macintosh WARNING • If the scanner is already connected to the SCSI card, the New Hardware Found dialog (old Windows 95 version) or Device Driver Wizard dialog (new Windows 95 version) will display. In this case, refer to Step 3 in Installing the Scanner Software (p. 22). Confirming the Status of the SCSI Card The following procedures show how to confirm that the SCSI card is operating correctly.
Windows Macintosh ○ 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Click the [Device Manager] tab and click the [+] mark beside the SCSI Controller item. • The SCSI card is operating correctly if “Adaptec AIC-7850 PCI SCSI Controller” displays underneath the SCSI Controller item. ○ 4 ○ ○ Click it. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ at the top right of each window to close • Windows NT 4.
Windows Macintosh Installing the SCSI Driver After the SCSI card has been installed, you should install the SCSI driver from the CanoScan Setup Utility CD-ROM onto the computer’s hard disk. The SCSI driver software is required to operate the SCSI card with your computer. Have the CanoScan Setup Utility CD-ROM close at hand and follow the steps below. • Windows 98 There is no need to install the SCSI driver provided on the CD-ROM.
Windows Macintosh ○ 2 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Click [Install the SCSI driver]. ▼Installation of the SCSI driver will commence. ○ 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Follow the instructions in the window to complete the installation.
Windows Macintosh Confirming the Status of the SCSI Card with Windows NT 4.0 After you have installed the SCSI card and driver, use the procedures below to ensure that they are operating correctly. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 1 Turn on the computer. 2 Click the Windows [Start] button on the taskbar and select [Settings] and [Control Panel].
Windows Macintosh Connecting to the Computer This section explains the procedures for connecting the scanner to the computer. Until the scanner operation is confirmed, place the scanner in a stable location near the computer. WARNING • Check the SCSI ID and terminator settings if multiple SCSI devices, other than the scanner, are connected. For details, please read When Connecting Two or More SCSI Devices in the Product Guide electronic manual.
Windows Macintosh ○ 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Attach the supplied SCSI interface cable to the SCSI connector on the computer. • The connectors on both ends of the SCSI interface cable are different. • To attach a Half Pitch 50-Pin (Male) connector, press the clips on both sides then insert it into the connector on the computer.
Windows Macintosh ○ 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Connect the other end of the SCSI interface cable to the scanner’s SCSI connector. • This scanner is equipped with two different connector types. Attach the matching connector on the SCSI interface cable to the scanner.
Windows Macintosh ○ 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Attach the power cord to the AC adapter. Power Cord ○ 7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Close the document cover. Plug the power cord into an electrical outlet. • Ensure that the document cover is closed before you plug in the power cord.
Installing the Software Windows Macintosh This section explains how to install the software contained on the accompanying CD-ROM. List of Software to be Installed The following software will be installed onto the computer. Windows • ScanGear CS-S Approx. 3 MB The software (TWAIN Driver) required to scan images into your computer. (Chapter 2 discusses TWAIN driver issues.) • ScanGear Toolbox CS Approx. 3 MB The software that loads and copies scanned images directly into registered programs.
Windows Macintosh Macintosh • Plug-in Module CS-S Approx. 700 KB (English version) (Multiply this by the number of programs with which it will be used.) The software required (Plug-in Software) to scan images into your computer. • CanoScan Toolbox CS Approx. 4 MB (English version) The software that loads and copies scanned images directly into registered programs. • Adobe Photoshop 5.0 LE Approx. 40 MB An image editing and retouching program. • Adobe Acrobat Reader 3.0 Approx.
Windows Macintosh Installing the Scanner Software Windows It is now time to install the software required to operate the scanner. This section explains the procedures for the Windows platform. For Macintosh, see page 34. ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Confirm that the scanner is correctly attached. • Confirm that the AC adapter is plugged into the scanner, and the power cord into the electrical outlet.
Windows Macintosh C Click the [Browse] button and specify the CD-ROM drive in the input box. Although this example uses [D:] as the CD-ROM drive Input the drive letter, your computer may letter corresponduse another letter, such as ing to your CD[E:] or [F:]. Substitute the ROM drive. appropriate drive letter for your system. ▼The required files will be loaded onto your computer and Windows will start. D Remove the CanoScan Setup Utility CD-ROM from the drive.
Windows Macintosh Add New Hardware Wizard Displays (Windows 98) A Click the [Next] button. B Select [Search for the best driver for your device] and click the [Next] button. C Place the CanoScan Setup Utility CD-ROM in the drive. D Select the CD-ROM drive and click the [Next] button. E Click the [Next] button if Canon CanoScan FB1200S Scanner displays in the following dialog.
Windows Macintosh F Click the [Finish] button. ▼Windows will start. G Remove the CanoScan Setup Utility CD-ROM from the drive. ○ 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Place the CanoScan Setup Utility CD-ROM in the computer drive. • Language select window will display to select your language, then the following window will automatically display.
Windows Macintosh ○ 5 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Click the [Install/Uninstall Software] button. ▼The following window will display. • If you accidentally click the wrong item, click the [Return to the previous menu] button and reclick the correct item. ○ 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Click the [Start Installation] button at the window’s bottom right.
Windows Macintosh WARNING • Please see the Users Registration Card for the serial number required to install Adobe Photoshop 5.0 LE. • If the installation is unsuccessful even when all the prescribed procedures are followed, read the following procedures. Installation does not seem to be working (Windows) Solution: Manually install the software by clicking the [Start] button, selecting [Run] and typing one of the command lines below into the box.
Windows Macintosh Trying Out the Scanner Windows The following instructions show you how to test the scanner and experiment with two software programs. You will use Adobe Photoshop 5.0 LE and ScanGear CS-S. WARNING • ScanGear CS-S is a TWAIN driver and cannot be started by itself. It has to be operated from an application software such as Adobe Photoshop 5.0 LE. For details, please read What is a TWAIN Driver? (p. 48).
Windows Macintosh Run the Scanning Software ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Place your document on the document glass as illustrated. • For the purposes of calibration, a single, thin sheet of paper is best. • Open the document cover, orient the image face down and align its top edge with the alignment mark at the back of the scanner. • Close the document cover, being careful not to dislodge the document.
Windows Macintosh ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Choose [CanoScan FB1200S] from the list and click the [OK] button. 4 Click the [File] menu and select [Import] and [TWAIN_32]. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ▼Calibration will commence. WARNING • Never lift the document cover during the calibration process.
Windows Macintosh • NOTE • • Calibration enables the scanner to reproduce colors more closely aligned to the original tones. It teaches your scanner the correct white balance from which to calculate the other colors. • Calibration will automatically be performed each time a preview or final scan is initiated. • When the scanner is used in low ambient temperatures, it may take a few moments for the unit to settle after the lamp lights.
Windows Macintosh Perform Scanning ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ To initiate the final scan, click the [Scan] button. • The final scan will be performed. WARNING • Never lift the document cover during the scanning process. • NOTE • • After clicking the [Scan] button, the calibration process commences again. ▼The scan will end when the Scanning progress dialog disappears from the window.
Windows Macintosh • NOTE • • The size of the image in the window will depend on the scanning resolution used. For ScanGear CS-S operating details, please read the ScanGear CS-S User’s Guide electronic manual. ○ 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Retouch or save the image as required. • ScanGear CS-S does not save the image, it only displays it in the Adobe Photoshop 5.0 LE window. To save it, use Adobe Photoshop 5.0 LE.
Windows Macintosh Installing the Scanner Software Macintosh The following procedures are for installing the software onto the Macintosh platform. For Windows, see page 22. ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Confirm that the scanner is correctly attached to the computer. • Check that the AC adapter is plugged into the scanner, and the power cord into the electrical outlet.
Windows Macintosh ○ 4 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Click the [Install Software] button. ▼The following window will appear. • Begin by installing Adobe Photoshop 5.0 LE. Quit all other applications that are running before starting the installation. • If Adobe Photoshop 5.
Windows Macintosh ○ 6 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ If the Adobe Photoshop 5.0 LE installation is complete and the following message displays, click [Restart]. ▼The computer will restart. WARNING • Restart the computer manually if you accidentally click the [Quit] button in the message above.
Windows Macintosh ○ 8 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Click the [Install Software] button again. ▼The following window will display. • Next, install the application programs other than Adobe Photoshop 5.0 LE. ○ 9 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ This time, click the [No] button. ▼The following window will display.
Windows Macintosh ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 10 Click the [Start Installation] button at the bottom right of the window. WARNING • Do not restart the computer or remove the CD-ROM from the drive while the installation is proceeding unless so directed by a CanoScan Setup Utility message. These actions would disrupt the installation. • Do not perform any other operations during the installation.
Windows Macintosh WARNING • If the installation is unsuccessful even when all the prescribed procedures are followed. Installation does not seem to be working (Macintosh) Solution: Please double-click the following icons, then install manually. To install Plug-in Module CS-S: CanonPI CS-S Installer To install CanoScan Toolbox CS: CanoScan Toolbox CS Installer To install Adobe Photoshop 5.0 LE: Adobe Photoshop 5.0 LE\English\Install Photoshop LE To install Adobe Acrobat Reader 3.
Windows Macintosh Trying Out the Scanner Macintosh The following instructions show you how to test the scanner and experiment with two software programs, an application program and a plug-in. You will use Adobe Photoshop 5.0 LE and Plug-in Module CS-S. WARNING • Plug-in Module CS-S is a plug-in and cannot be started by itself. It has to be operated from an application program, such as Adobe Photoshop 5.0 LE. For details, please read What is a Plug-In ? (p. 54).
Windows Macintosh Run the Scanning Software. ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Place your document on the document glass as illustrated. • For the purposes of calibration, a single, thin sheet of paper is best. • Open the document cover, orient the image face down and align its top edge with the alignment mark at the back of the scanner. • Close the document cover, being careful not to dislodge the document.
Windows Macintosh • NOTE • • Calibration enables the scanner to reproduce colors more closely aligned to the original tones. It teaches your scanner the correct white balance from which to calculate the other colors. Calibration is conducted each time a preview or final scan is initiated. ▼When calibration is complete, the preview scan will initiate, gradually displaying the image. The image that appears in the window is merely a preview image.
Windows Macintosh Perform Scanning ○ 1 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ To initiate the final scan, click the [Scan] button. The Plug-in Module CS-S window will disappear and the final scan will be performed. WARNING • Never lift the document cover during the scanning process. • NOTE • • After clicking the [Scan] button, the calibration process commences again. ▼The scan will end when the Scanning progress window disappears.
Windows Macintosh ○ 2 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Retouch or save the image as required. • Plug-in Module CS-S does not save the image, it only displays it in the Adobe Photoshop 5.0 LE window. To save it, use Adobe Photoshop 5.0 LE. Instructions for Adobe Photoshop 5.0 LE are in the electronic manual on the CD-ROM. • Quit Adobe Photoshop 5.0 LE after checking the image file.
CHAPTER 2 Guide to the Software Here, we introduce each program that was installed in the last chapter. How to Use the Software ................................................................ 46 Windows Platform Using ScanGear CS-S ................................................................. 47 Scanning with ScanGear Toolbox CS .......................................... 49 Scanning with Adobe Photoshop 5.0 LE .................................... 50 Scanning with Caere OmniPage Limited Edition .....
How to Use the Software Windows Macintosh The following software is included with this scanner. Windows • • • • • ScanGear CS-S 4.3 ScanGear Toolbox CS 1.1 Adobe Photoshop 5.0 LE Caere OmniPage Limited Edition 5.1 Adobe Acrobat Reader 3.0 Macintosh • • • • Plug-in Module CS-S 3.6 CanoScan Toolbox CS 1.0 Adobe Photoshop 5.0 LE Adobe Acrobat Reader 3.0 The next pages provide a simple introduction to the purpose, characteristics and use of each program. Please read them at your leisure.
Windows Macintosh Using ScanGear CS-S ScanGear CS-S is a program that loads images. You can also use it to adjust the image as it is scanned. It is used as a TWAIN driver. For more detail, please read What is a TWAIN Driver? (p. 48).
Windows Macintosh How to Use ScanGear CS-S • Starting ScanGear CS-S Select [TWAIN_32] as a TWAIN driver from a program (p. 29). • How to View the Electronic Manual Place the CD-ROM in the CD-ROM drive, click [View the Electronic Manuals] and select [ScanGear CS-S]. The procedures to read the electronic manuals are explained in the section entitled Viewing Electronic Manuals with Adobe Acrobat Reader 3.0 (p. 57).
Scanning with ScanGear Toolbox CS Windows Macintosh ScanGear Toolbox CS is a software which makes scanning easier. You can easily scan just by clicking the buttons in ScanGear Toolbox CS. The scanned images will be loaded automatically into the selected application program. You can also copy images. (1) For example, click the [Copy] button (2) the document is automatically scanned (3) Print directly with the printer Convenient at Times Like These • When you want to fax or E-mail the scanned images.
Scanning with Adobe Photoshop 5.0 LE Windows Macintosh Adobe Photoshop 5.0 LE can retouch and manipulate images. Scan the pictures... Convenient Applications of Adobe Photoshop 5.0 LE • • • • Correcting images, such as those that are too dark or bright. Adding special effects, such as the mosaic or wave effect, to images. Creating reports, presentation materials or websites with images. Effortlessly creating original postcards, invitations, business cards, labels or CD covers with images.
Windows Macintosh Scanning with Caere OmniPage Limited Edition Caere OmniPage Limited Edition is an optical character recognition (OCR) program that converts scanned words into text data that can be edited with word processors. Convert the graphics file data into text data Scan a text document Convenient Applications of Caere OmniPage Limited Edition • Converting words scanned from a book, magazine, newspaper or fax into text data for editing or digital transmission.
Windows Macintosh • How to View the Electronic Manual Place the CD-ROM in the CD-ROM drive, click [View the Electronic Manuals] and click [Caere OmniPage Limited Edition 5.1] button. For details, please read View the Electronic Manual with Adobe Acrobat Reader 3.0 (p. 57). • NOTE • 52 • When you install Caere OmniPage Limited Edition, the [Select Source] dialog will display. Choose the CanoScan FB1200S option. This instructs Caere OmniPage Limited Edition to select the correct scanner for scanning.
Windows Macintosh Using Plug-in Module CS-S Plug-in Module CS-S is a software which acquires the image. The image file to satisfy you can be created with the numerous adjustment functions. It is used as a plug-in software (More about plug-in software later). Click here to display numerous menus. You can set the scan mode, scan resolution, image size. Click here to adjust the brightness.
Windows Macintosh How to Use Plug-in Module CS-S • Starting Plag-In Module CS-S Select [Canon PI CS-S 3.6] as a plug-in from the application program (P. 41). • How to View the Electronic Manual Place the CD-ROM in the CD-ROM drive, click [View the Electronic Manuals] and click [Plug-in Module CS-S (English version)] button. For details, please read View the Electronic Manual with Adobe Acrobat Reader 3.0 (P. 57).
Scanning with CanoScan Toolbox CS Windows Macintosh CanoScan Toolbox CS is a software which makes scanning easier. You can easily scan just by clicking the buttons in [CanoScan Toolbox CS]. The scanned images will be loaded automatically into the selected application program. You can also copy images. (1) For example, click the [Copy] button (2) the document is automatically scanned (3) Print directly with the printer Convenient at Times Like These • When you want to fax the scanned images.
Scanning with Adobe Photoshop 5.0 LE Windows Macintosh Adobe Photoshop 5.0 LE can retouch and manipulate images. Scan the pictures... Convenient Applications of Adobe Photoshop 5.0 LE • • • • Correcting images, such as those that are too dark or bright. Adding special effects, such as the mosaic or wave effect, to images. Creating reports, presentation materials or websites with images. Effortlessly creating original postcards, invitations, business cards, labels or CD covers with images.
Windows Macintosh Viewing Electronic Manuals with Adobe Acrobat Reader 3.0 The operation procedures for Product Guide, ScanGear CS-S, Plug-in Module CS-S, CanoScan Toolbox CS, Adobe Photoshop 5.0 LE and Caere OmniPage Limited Edition electronic manuals are contained on the CanoScan Setup Utility CD-ROM. An electronic manual is not a printed manual but a manual intended to be read on the computer screen. Adobe Acrobat Reader 3.0 is a program used to read the electronic manuals.
Windows Macintosh ○ 3 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Select the manual you wish to view. • Adobe Acrobat Reader will automatically start and display the manual. Navigate through the manual using the program’s menus and buttons. The diagram below explains the minimum necessary functions required to view an electronic manual.
System Information This form is used to record the operating environment of the purchased scanner. If any problems occur with the scanner, you will need this information when you contact our Customer Support Help Desk. Please make sure to record this and secure it safely. • When repair is needed, warranty information is required. Please make sure to record information and secure carefully. • The replacement parts for servicing this equipment have an expiration date of seven years after production.
Use of shielded cable is necessary to comply with the technical requirements of the EMC Directive. Caution: 1. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Canon Inc. 2. The equipment and software described in this guide are subject to change without notice. 3. Notwithstanding the considerable care taken in preparing this guide, please note that Canon Inc.
CANON (UK) LTD. Woodhatch, Reigate Surrey RH2 8BF, United Kingdom For technical support, please contact Canon Helpdesk. Helpdesk: P.O. Box 431, Wallington, Surrey SM6 0XU TEL: (08705) 143 723 FAX: (08705) 143 340 For sales enquiries: (0121) 666-6262 CANON FRANCE S.A. 17, quai du Président Paul-Doumer 92414 Courbevoie Cedex, France Tél.01 4199 7777 Fax.01 4199 7951 Hotline: Tél.
