Operation Manual
Table Of Contents
- DR-2010C/DR-2510C/DR-2010M/DR-2510M User Manual
- Introduction
- Contents
- Chapter 1 Before Using the Scanner
- Chapter 2 Setup
- Chapter 3 Basic Operation
- Chapter 4 CaptureOnTouch Settings
- Chapter 5 Other Scanning Methods
- 1. Scanning with CapturePerfect 3.0
- 2. Basic Scanning Procedure
- 3. Using the Scan Panel
- 4. Special Scanning
- Enhancing the Text of a Document
- Scanning Documents That Include Both Color and Black-and-White Pages
- Scanning Different Sized Documents Together
- Skipping Blank Pages
- Scanning (Single-Sided) 11" X 17"/A3 Documents
- Deskewing Documents
- Moire Reduction
- Correcting the Text Orientation of Documents
- Reducing Bleed Through for Thin Documents and Documents with Dark Reverse Sides
- Deleting Borders and Ruled Lines of a Specified Color (Red/Green/Blue)
- Enhancing the Red color for Black-and-White Scanning
- Creating Smaller Files
- Saving the Text Data of Documents as Search Keywords
- Specifying Security Settings for PDF Files (Windows only)
- Chapter 6 Scanner Driver Settings
- 1. Before Using the Scanner
- 2. Scan driver settings
- Scan Mode Settings
- Auto Color Detection
- Paper Size Settings
- Scan Resolution Settings
- Scanning Side Settings
- Correcting Image Skewing
- Moire Reduction
- Adjusting the Scan Area
- Brightness/Contrast Adjustment
- Gamma Curve Settings
- Image Contour Adjustment
- Image Rotation
- Correcting Text Orientation
- Removing the Document Background/Preventing Bleed Through
- Omitting a Specific Color
- Enhancing the Red Color
- Rapid Recovery System
- Double Feed Detection
- Feeding Options
- Prescan
- Registering Scanning Conditions
- Checking the Version
- Chapter 7 Maintenance
- Chapter 8 Troubleshooting
- Chapter 9 Appendix
- INDEX
Back Previous Page Next Page
Contents
22
IMPORTANT
A document must meet the following criteria to be scannable:
• When scanning multiple documents of different sizes, place the documents
so that they cover the entire span of the feed rollers.
• It is recommended that documents exceeding LTR, 11.69" (A4, 297 mm) size
are fed one sheet at a time.
• Scanning documents before the ink is dry can cause problems with the
scanner. Always make sure that the ink on a document is dry before scanning
it.
• Scanning documents that are written in pencil or similar material may make
the rollers and scanning glass dirty, which can lead to smudges on the
scanned image and transfer the dirt to subsequent documents. Always clean
the internal parts of the scanner after scanning such documents.
• When scanning a two-sided document that is printed on thin paper, the
image on the opposite side of each page may show through. In this case,
adjust the scanning intensity in the application software before scanning the
document.
• It is recommended that thin documents are fed one sheet at a time.
• Scanning the following types of documents can cause a paper jam or
malfunction. To scan such a document, make a photocopy of the document
and then scan the photocopy.
Business Card
Size: 1.97"x 2.12" (50 mm x 53.9 mm) or larger
Paper weight: 140 lb bond (300g/m
2
) 0.0138" (0.35 mm) or less
IMPORTANT
If a stack of business cards cannot be fed properly, reduce the number of cards
in the stack.
Card
Size: 2.12" x 3.37" (53.9 mm x 85.5 mm) (ISO/JIS standard)
Card thickness: 0.03" (0.76 mm) or less
Orientation: Horizontal feeding only
Embossed cards can be scanned.
CAUTION
• If you place cards to be fed vertically, they may not be ejected properly, and
cards that get jammed may be damaged when you remove them. Take care
of the orientation when placing cards.
• Embossed cards may not be able to be scanned correctly, depending on the
type of embossment.
Wrinkled or creased
documents
Carbon paper
Curled documents Coated paper
Torn documents
Extremely thin, translucent
paper
Documents with paper clips
or staples