Wireless File Transmitter WFT-E6 for EOS-1D X Mark II This manual explains how to use Wireless File Transmitter WFT-E6 with the EOS-1D X Mark II. This manual is for the EOS-1D X Mark II installed with firmware version 1.1.0 or later. This product also supports certain CINEMA EOS cameras. For compatible products, contact the nearest Canon Service Center. When using the transmitter, refer to “Guide for Canon Camcorders”.
Introduction What You Can Do with the Transmitter The transmitter is an accessory for EOS cameras that enables wireless functions when attached to the camera.
Conventions Used in this Manual To comply with local radio wave regulations, Canon offers five region-specific versions of the transmitter (A, B, C, D, and E) in various areas around the world (see separate sheet). For convenience, the product in this manual is referred to as “WFT-E6”, without reference to the versions A, B, C, D, or E. In this manual, the term “access point” indicates wireless LAN access points, wireless LAN routers, etc. that relay a LAN connection.
Conventions Used in this Manual Basic Assumptions All operations explained in this manual assume that the power switch is set to <1>. It is assumed that all the menu settings, Custom Functions, etc. are set to their defaults. Image transfer, remote shooting, or viewing images requires adequate knowledge of configuring your wireless LAN and FTP server. Canon cannot provide support for configuring wireless LANs or FTP servers.
Chapter List Introduction 2 1 Basic Network Settings 13 2 Transferring Images to an FTP Server 37 3 Operating Remotely Using EOS Utility 55 4 Operating Remotely Using WFT Server 59 5 Operating Remotely Using a Smartphone 75 6 Linked Shooting 83 7 Synchronizing the Camera Time Wirelessly 97 8 Terminating the Connection and Reconnecting 101 9 Checking and Operating Connection Settings 105 10 Troubleshooting Guide 117 11 Reference 139 5
Contents Introduction 2 Conventions Used in this Manual..................................................... 3 Chapter List ...................................................................................... 5 Safety Precautions ........................................................................... 8 Nomenclature ................................................................................. 10 Attaching to the Camera..................................................................
Contents 5 Operating Remotely Using a Smartphone 6 Linked Shooting 7 Synchronizing the Camera Time Wirelessly 8 Terminating the Connection and Reconnecting 75 Configuring Smartphone Connection Settings................................ 76 Operating the Camera Using a Smartphone................................... 78 Specifying Viewable Images ........................................................... 80 83 Basic Linked Shooting ....................................................................
Safety Precautions The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product. Warnings: Follow the warnings below. Otherwise, death or serious injuries may result. To prevent fire, excessive heat, chemical leakage, explosions, and electrical shock, follow the safeguards below.
Safety Precautions Handling Precautions The transmitter is a precision instrument. Do not drop it or subject it to physical shock. The transmitter is not waterproof. Do not use it underwater. Wipe off any moisture with a dry and clean cloth. If the transmitter has been exposed to salty air, wipe it with a clean, well-wrung wet cloth. Never leave the transmitter near any equipment that generates a strong magnetic field, such as magnets or electric motors.
Nomenclature Attachment pin Tightening screw Terminal Terminal cap Transmitter Case EOS-1D X Mark II Rear LCD Panel (Example Display) Wireless LAN connection Connection icon Wired LAN connection 10
Attaching to the Camera Set the camera’s power switch to <2> before attaching the transmitter. The transmitter is powered by the camera. Ensure the camera battery has sufficient charge. If the battery level drops to 19% or less, you cannot transfer captured images. 1 Open the terminal cover on the camera. Pull out the system extension terminal cover and rotate it toward the front. the transmitter.
Attaching to the Camera Use of an External Microphone during Movie Shooting If wireless functions are in use, noise may be recorded regardless of the use of the built-in microphone(s) or an external microphone. It is recommended that you do not use wireless functions when shooting movies.
1 Basic Network Settings Complete the basic network settings by using the menu screen on the camera’s LCD monitor.
Preparation [FTP trans.] You can transfer captured images to an FTP server. Images can be automatically transferred as you shoot them, or you can select images to be transferred later. Computer Operating Systems Use of [FTP trans.] requires that one of the following operating systems be installed on a computer. In addition, the computer must be set up as an FTP server in advance. • Windows 8, Windows 8 Pro, Windows 8.1, Windows 8.
Preparation [EOSUtility] You can perform remote shooting over a wireless LAN using EOS Utility (EOS software). In addition to remote shooting, almost all EOS Utility camera operations are supported, because this option utilizes a wireless LAN instead of an interface cable. Requires a computer with EOS Utility (EOS software) installed.
Preparation [Smartphone] You can perform basic remote shooting or view images stored in the camera on a smartphone or tablet. To use this function, a smartphone on which iOS or Android is installed is necessary. In addition, the dedicated application Camera Connect (free of charge) must be installed on the smartphone. • Camera Connect can be downloaded from the App Store or Google Play. • For the operating system versions supported by Camera Connect, refer to the download site of Camera Connect.
Preparation Connecting Using an Access Point When connecting using an access point, connect the target device to the access point in advance. Transmitting Movies Because of the large size of individual movie files, wireless file transmission takes some time. Set up an environment where each device can achieve stable communication with the access point and the transmitter by referring to the information on page 136.
Basic Communication Function Settings First, configure basic communication function settings. Setting the Communication Function 1 Turn the camera on. [Communication settings]. 2 Select On the camera, press the button. Under the [53] tab, select [Communication settings], then press <0>. [Enable] in 3 Select [Communication func]. [Network settings] is now available. If [z1: Multiple exposure] is set to any setting other than [Disable], [53: Communication settings] cannot be selected.
Basic Communication Function Settings Registering a Nickname Set a nickname (for identification) for the camera. When the camera is connected to another device over a LAN, the nickname will be displayed on the device. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. 3 Select [Nickname].
Basic Communication Function Settings a nickname. 4 Enter For instructions on entering characters, see the next page. Enter any characters between 1 to 10 characters in length. the setting. 5 Exit When you are finished, press the button. Select [OK] on the confirmation dialog and press <0> to return to the menu screen. The basic settings for the communication function are now complete. For further explanation of syncing the camera time and linked shooting, see the following pages.
Basic Communication Function Settings Virtual Keyboard Operation Changing the entry area Press the button to toggle between the top and bottom entry areas. Moving the cursor Use <5> or <9> in the top area to move the cursor. Entering text In the bottom area, use <5> or <9> to select a character, then press <0> to enter it. You can check how many characters you have entered, and how many more can be entered, by referring to [*/*] on the upper right of the screen.
Displaying the Connection Wizard This section describes the process following the connection instructions. If an error is displayed, see “Troubleshooting Guide” in Chapter 10 (p.117) and check the settings. Pressing the shutter button or other camera controls during configuration using the connection instructions will close the connection instructions. Do not press the shutter button or other controls until configuration is finished. Under the [52] tab, set [Auto power off] to [Disable].
Displaying the Connection Wizard 4 Select [SET*]. [Connection wizard]. 5 Select The [Select communication method] screen is displayed. The lamp on the camera will blink in green. the communication 6 Select method. Select the communication method by referring to page 14. Select [OK] and press <0> to go to the next screen. [Wireless]. 7 Select Select [OK] and press <0> to go to the next screen. Select [Wired] when using a network cable for the Ethernet RJ-45 terminal on the camera.
Displaying the Connection Wizard the connection method. 8 Select Not displayed when [FTP trans.] is selected in step 6. Proceed to step 9. Select an item, then press <0>. To connect the camera directly to each device, select [Easy connection]. Proceed to page 25. To connect using a Wi-Fi access point, select [Select a network]. Proceed to step 9. Select [OK] and press <0> to go to the next screen. the network. 9 Select Select a network connection method. For subsequent operations, see page 27.
Connecting with Easy Connection The instructions in this chapter are continued from page 24. The camera and each device can be directly connected wirelessly. No access point is necessary, so you can establish a wireless connection easily. To establish connection, operations on the computer, smartphone, etc. are required. For details, refer to the corresponding device’s instruction manual. 1 SSID (network name) Encryption key (password) Select [Easy connection].
Connecting with Easy Connection Completing Settings for the Communication Method The following instructions are for settings screens that vary depending on the communication method. Read the page that introduces the selected communication method. EOS Utility Chapter 3 (p.55) WFT Server Chapter 4 (p.59) Smartphone Chapter 5 (p.
Checking the Type of Access Point To connect using an access point, check if the access point supports WPS* that allows easy connection between Wi-Fi devices. If you do not know if the access point you use is WPS-compatible, refer to the access point instruction manual or other documentation. * Wi-Fi Protected Setup When WPS is supported The following two connection methods are available. Connection can be established easier with WPS (PBC mode).
Connecting via WPS (PBC Mode) The instructions in this chapter are continued from page 27. This is a connection mode available when using an access point compatible with WPS. In pushbutton connection mode (PBC mode), the camera and the access point can be connected simply by pressing the WPS button on the access point. If multiple access points are active in the surrounding area, it may be more difficult to establish a connection. In such a case, try using [WPS (PIN mode)] to establish a connection.
Connecting via WPS (PIN Mode) The instructions in this chapter are continued from page 27. This is a connection mode available when using an access point compatible with WPS. In PIN code connection mode (PIN mode), an 8digit identification number specified on the camera is set at the access point to establish a connection. Even if there are multiple access points active in the surrounding area, a relatively reliable connection can be established using this shared identification number.
Connecting via WPS (PIN Mode) to the access point. 4 Connect Select [OK] and press <0> to establish a connection with the access point. When a connection with the access point is established, the [IP address set.] screen (p.34) is displayed.
Connecting to a Detected Network Manually The instructions in this chapter are continued from page 27. Establish a connection by selecting the SSID (or ESS-ID) of the access point to connect to from a list of active access wireless LAN terminals nearby. Selecting the Access Point (1) (2) (3) 1 Select an access point. Turn the <5> dial to select the access point to connect to from the list of access points.
Connecting to a Detected Network Manually Entering the Access Point Encryption Key Enter the encryption key (password) specified for the access point. For details on the specified encryption key, refer to the access point’s instruction manual. The screens displayed in steps 2 to 4 below vary depending on the authentication and encryption specified for the access point. Go to page 34 when the [IP address set.] screen is displayed instead of the screens for steps 2 to 4. a key index.
Connecting to a Detected Network Manually the encryption key. 4 Enter Enter the encryption key using the virtual keyboard (p.21), then press the button. When a connection with the access point is established, the [IP address set.] screen (p.34) is displayed.
Setting the IP Address Select [Auto setting]. Select [OK] and press <0> to display the setting screen for the communication method (p.35). If [Auto setting] results in an error or if you want to specify the settings manually, see page 144. The IP address can only be set automatically in environments using DHCP servers, or access points or routers with DHCP server functionality, such that IP addresses and related settings are assigned and configured automatically.
Setting the IP Address Completing Settings for the Communication Method The following instructions are for settings screens that vary depending on the communication method. Read the page that introduces the selected communication method. FTP Transfer Chapter 2 (p.37) EOS Utility Chapter 3 (p.55) WFT Server Chapter 4 (p.59) Smartphone Chapter 5 (p.
Setting the IP Address Camera Access Point Mode Camera access point mode is a connection mode for connecting the camera directly to each device. Displayed when [EOSUtility], [WFTserver], or [Smartphone] is selected for the communication method. In camera access point mode, the following two connection methods are available. [Easy connection]: See “Connecting with Easy Connection” (p.25) to establish a connection. [Manual connection]: See page 142 to establish a connection.
2 Transferring Images to an FTP Server By connecting to an FTP server, you can transfer images stored in the camera to a computer. With FTP transfer, you can automatically transfer images to the FTP server as you shoot or transfer a set of shots together. The instructions in this chapter are continued from Chapter 1.
Configuring FTP Server Connection Settings These instructions are continued from Chapter 1. 1 Select an FTP mode. To establish security for FTP transfer using a root certificate, select [FTPS]. For root certificate settings, see page 41. Select [OK] and press <0> to go to the next screen. [Address setting]. 2 Select The virtual keyboard is displayed. the FTP server’s server 3 Enter name or IP address.
Configuring FTP Server Connection Settings the port number. 4 Set [Port number setting] should usually be 00021. Select [OK] and press <0> to go to the next screen. the passive mode setting. 5 Set Select [OK] and press <0> to go to the next screen. If an Error 41 (“Cannot connect to FTP server”) is displayed in step 8, setting [Passive mode] to [Enable] may resolve it. the proxy server. 6 Set Select [OK] and press <0> to go to the next screen. the login method.
Configuring FTP Server Connection Settings the target folder. 8 Set Select [Root folder] to have images saved in the root folder as specified in FTP server settings (p.53). Select [Select folder] to specify a target folder in the root folder. If no folder exists, a folder will be created automatically. Select [OK] and press <0> to go to the next screen. The lamp on the camera will light up in green. [OK]. 9 Select Press <0>. A connection completion screen will appear. [OK].
Configuring FTP Server Connection Settings Importing a Root Certificate for FTPS If the FTP mode is set to [FTPS] when configuring the connection settings, the same root certificate as the FTP server must be imported to the camera. Only the root certificate whose file name is “root.cer”, “root.crt”, or “root.pem” can be imported to the camera. Only one root certificate file can be imported to the camera. Insert a card containing the root certificate file in advance. 1 Select [Communication settings].
Configuring FTP Server Connection Settings 5 Select [Set root certif]. [Load root certif from 6 Select card]. [OK]. 7 Select The root certificate is imported. Select [OK] on the confirmation dialog to return to the [Set root certif] screen. Select [Delete root certificate] on the screen for step 6 to delete the root certificate imported to the camera. Select [View root certificate details] to check the issuer, subject, validity period, and other information.
Transferring Images Individually Automatic Image Transfer After Each Shot An image can be automatically transferred to the FTP server immediately after shooting. You can also continue still photo shooting even while images are being transferred. Before shooting, be sure to insert a card into the camera. If you shoot without recording images, they cannot be transferred. Note that automatic transfer of movies during shooting is not supported. Transfer the movie after shooting, as described on pages 48-52.
Transferring Images Individually [Automatic transfer]. 5 Select Select [Enable]. the picture. 6 Take The captured image is transferred to the FTP server. During continuous shooting, images are transferred to the FTP server in the order they are captured. The captured images are also stored on the card. Any images for which transfer fails or is interrupted will be transferred automatically when the connection is recovered (p.47).
Transferring Images Individually Transferring the Current Image Simply play back an image and press <0> to transfer it. You can also continue still photo shooting even while images are being transferred. 1 Select [Transfer with SET]. On the setting screen of FTP transfer, select [Transfer with SET]. Select [Enable]. the image. 2 Select Press the button on the camera. Select the image to transfer, then press <0> to transfer the image. Movies cannot be transferred this way.
Transferring Images Individually Selecting Particular Sizes or Types of Images to Transfer You can select which images to transfer when recording images of different sizes to a CF card and CFast card simultaneously, or when shooting in RAW+JPEG image quality. Select [Transfer type/size] in step 5 on page 44 to select the size or type of images to transfer. 1 Select [Transfer type/size]. the size and type of images 2 Select to transfer.
Transferring Images Individually Auto Retry if Transfer Fails If transfer fails, the lamp on the camera blinks in red. In this case, press the button, select [Communication settings] under the [53] tab, and press <0>. When the screen shown on the left is displayed, check the error code number and see page 118 to eliminate the cause of the error. Once the cause of the error is eliminated, the images whose transfer previously failed will be re-transferred automatically.
Batch Transfer After shooting, you can select multiple images as desired and transfer them all at once. You can also transfer unsent images or images that could not be sent previously. Additionally, you can add a caption before transferring images. You can also continue still photo shooting even while images are being transferred. When the Live View shooting/Movie shooting switch is set to , images cannot be transferred. Set it to . Selecting the Images to be Transferred Sel.
Batch Transfer images to transfer. 4 Select Turn the <5> dial to select the image to be transferred, then press <0>. Turn the <5> dial to display the [X] on the screen’s upper left, then press <0>. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the <6> dial clockwise. To select other images to be transferred, repeat step 4. the image.
Batch Transfer Sel.n Select [Sel.n] and select [Select images not transferred]. When you select a folder, all the images in that folder not yet transferred to the FTP server will be selected. When you select [Sel img not transfer. (J only)] and select a folder, the protected images in that folder not yet transferred to the FTP server will be selected. Selecting [Select transfer failed images] will select the selected folder’s images that failed to be transferred.
Batch Transfer Transferring RAW+JPEG Images For RAW+JPEG images, you can specify which image to transfer. In step 2 on page 48, select [RAW+JPEG transfer], and select the image to be transferred: [JPEG only], [RAW only], or [RAW+JPEG]. The [RAW+JPEG transfer] setting switches in tandem with the [RAW+JPEG transfer] setting under [53: Communication settings] 9 [Network settings] 9 [Function settings] 9 [FTP transfer settings] 9 [Transfer type/size] (p.46).
Batch Transfer Adding a Caption Before Transfer When you select [Transfer with caption] in step 2 on page 48, you can add a registered caption to each image before transfer. This is convenient if you want to inform the recipient of the printing quantity, for example. The caption is also added to images stored in the camera. You can check captions added to images by examining the Exif information, in the user comments. For instructions on creating and registering captions, see page 140.
Viewing Transferred Images Images transferred to the FTP server are stored in the following folder as specified in the FTP server settings. Target Folders for the FTP Server Under the default settings of the FTP server, images are stored in [C drive] 9 [Inetpub] folder 9 [ftproot] folder, or in a subfolder of this folder. If the root folder of the transfer destination has been changed in the FTP server settings, ask the FTP server administrator where images are transferred.
MEMO 54
3 Operating Remotely Using EOS Utility Using EOS Utility, you can view images stored in the camera or save them to a computer. Additionally, you can operate the camera remotely to take a picture or change camera settings using EOS Utility. Almost all EOS Utility camera operations are supported, because this option utilizes a wireless LAN instead of an interface cable. The instructions in this chapter are continued from Chapter 1. Install EOS Utility on the computer before setting up a connection (p.
Configuring EOS Utility Connection Settings These instructions are continued from Chapter 1. To establish a connection, operations on the computer are required. For details, refer to the computer’s instruction manual. The configuration procedure is as follows, using Windows 8.1 as an example. Operation on the Camera-1 1 Select [OK]. Select [OK] and press <0>. The following message is displayed. “******” represents the last six digits of the MAC address of the transmitter.
Configuring EOS Utility Connection Settings [Connect] on the computer. 4 Click Select the camera to connect to, then click [Connect]. If multiple cameras are displayed, identify the camera to connect to by its MAC address displayed on the camera’s LCD monitor. The MAC address can also be checked on the [Function settings] screen (p.114). Operation on the Camera-2 [OK]. 5 Select When the camera detects the computer on which you clicked [Connect] in step 4, the screen on the left is displayed.
Using EOS Utility For EOS Utility instructions, refer to the EOS Utility Instruction Manual. In addition to remote shooting, various camera operations are available. In Remote Live View shooting, the rate of image transmission is slower compared to a connection via an interface cable. Therefore, moving subjects cannot be displayed smoothly. While connected, [Multiple exposure], [RAW image processing], [Cropping], or [Resize] cannot be selected.
4 Operating Remotely Using WFT Server Using a web browser, you can view images stored in the camera or save them to a computer, smartphone, etc. Additionally, you can operate the camera remotely to take a picture or change camera settings using a web browser. The instructions in this chapter are continued from Chapter 1.
Configuring WFT Server Connection Settings These instructions are continued from Chapter 1. Enter a login name and password for connecting to the camera from a computer. The login name and password you specify here are used when connecting to the camera. 1 Select [User *]. With WFT Server, you can connect the camera to up to three devices. Select a user number to prevent conflicts when users at other devices are connected simultaneously. [Login name] or 2 Select [Password].
Configuring WFT Server Connection Settings [OK]. 4 Select Select [OK] and press <0>. A connection completion screen will appear. [OK]. 5 Select Press <0> to return to the [Network settings] screen. Settings information is stored in the camera. It is not stored in the transmitter. The settings for connecting to WFT Server are now complete. You can change the WFT account settings on the [Function settings] screen (p.114). The port number setting can also be changed on the [Function settings] screen.
Displaying WFT Server In the web browser, display WFT Server, a screen for transmitter operations. Connect the camera to a computer, smartphone, etc. via LAN in advance. Checking the Camera’s IP Address To access the camera from a web browser, the camera’s IP address displayed in step 6 must be entered in the address field of the web browser. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings].
Displaying WFT Server [Confirm settings]. 5 Select The settings are displayed. the settings. 6 Check Turn the <5> dial to display other screens. Write down the IP address. After checking it, press the button to exit the confirmation dialog. Logging in to WFT Server the web browser. 7 Start Start a web browser on a computer, smartphone, etc. Enter the URL. 8 In the address field, enter the IP address you wrote down in step 6. Press the key.
Displaying WFT Server the [Login name] and 9 Enter [Password]. Enter the [Login name] (user name) and [Password] specified on page 60. Press [OK] to display the WFT Server screen. the language. 10 Select Select a language at the bottom of the screen. WFT Server cannot be used unless the web browser supports JavaScript. While connected, [Multiple exposure], [RAW image processing], [Cropping], or [Resize] cannot be selected.
Viewing Images You can browse images on the camera’s card as follows. 1 Press [3 Viewer]. The image viewing screen is displayed. the card and folder. 2 Select Press the [CF] or [CFast] tab to select a card. Press the folder name on the right of the selected tab to select a folder from the pull-down list. an image. 3 Select To view other images, change the screen with [ ] or [ ] at the bottom of the screen.
Viewing Images images. 4 Download When you select a thumbnail, the image is displayed at a larger size. Press [ ] to download the image. Press [ ] or [ ] to display the previous or next image. Press [ ] to return to the image viewing screen. Still photo playback screen Movie playback screen Note that due to the performance of computers and smartphones, or browsers used, the following may occur: Images cannot be displayed, images are displayed slowly, or images cannot be downloaded to the devices.
Shooting Remotely [Camera control] You can use WFT Server to shoot remotely. 1 Press [z Camera control]. The advanced capture screen is displayed.
Shooting Remotely [Camera control] the lens’s focus mode switch 2 Set to . When you press and let go of the Shutter button (6), the camera will autofocus and take a picture. Drive mode (2) displays the drive mode set on the camera. Note that even if the camera’s drive mode is set to continuous shooting, single shooting will apply for remote shooting. When the camera’s Live View shooting/Movie shooting switch is set to , still photo shooting is not possible.
Shooting Remotely [Camera control] Displaying Live View Image for Shooting 1 Display Live View image. Press the Still photo Live View shooting button (15). the focus. 2 Adjust Using autofocus Press [ON] on the AF button (7) to autofocus. Focusing manually Press the buttons < >, < >, < >, < >, < >, and < > to adjust the focus. To focus more closely, press < >, < >, or < >. To focus farther away, press < >, < >, or < >. Three levels of focus adjustment are available.
Shooting Remotely [Camera control] the shooting settings. 3 Configure Select setting items (such as imagerecording quality) to view the setting details, which you can configure. Complete the settings as needed. the picture. 4 Take Press the Shutter button (6). When you let go of the button, the picture is taken. The captured image is displayed. Captured images are stored on the camera’s card. To download images, see “Viewing Images” (p.65).
Shooting Remotely [Camera control] Shooting Movies Press the Movie shooting button (16) to display the movie shooting screen. The setting procedures are the same as still photo shooting. Press the Shutter button (6). When you let go of the button, movie shooting will start. During movie shooting, the red [o] on the Shutter button (6) changes to a white [n]. Press the Shutter button (6) again. When you let go of the button, movie shooting will stop.
Shooting Remotely [Simple control] Although detailed function settings are not available on the basic capture screen, it is convenient for shooting remotely using a smartphone or other small-screen devices due to the compact design of the operation screen. 1 Press [ Simple control]. The basic capture screen and Live View image are displayed.
Shooting Remotely [Simple control] the focus. 2 Adjust Set the lens’s focus mode switch to . Using autofocus Press [ON] on the AF button to autofocus. Focusing manually Press the buttons < >, < < >, < >, < >, and < adjust the focus. >, > to the picture. 3 Take Press the Shutter button. When you let go of the button, the picture is taken. The captured image is displayed. Captured images are stored on the camera’s card. To download images, see “Viewing Images” (p.65).
Using WFT Server in Linked Shooting Remote shooting in WFT Server can be used in conjunction with the transmitter’s “Linked Shooting” function (p.83). Additionally, images on the master camera’s card and slave cameras’ cards can be viewed and downloaded.
5 Operating Remotely Using a Smartphone Using a smartphone, you can view images stored in the camera or save them to the smartphone. Additionally, you can operate the camera remotely to take a picture or change camera settings using a smartphone. The instructions in this chapter are continued from Chapter 1. Install Camera Connect on the smartphone before setting up a connection (p.16).
Configuring Smartphone Connection Settings These instructions are continued from Chapter 1. To establish connection, operations on the smartphone are required. For details, refer to the smartphone’s instruction manual. Operation on the Smartphone 1 Start Camera Connect on the smartphone. When the [Waiting to connect] screen is displayed on the camera’s LCD monitor, start Camera Connect on the smartphone. the camera to connect to 2 Select on the smartphone.
Configuring Smartphone Connection Settings Operation on the Camera to the camera. 3 Connect When a connection is established, The device name set on Camera Connect the screen on the left will appear on the camera’s LCD monitor. To specify viewable images, press the button. See step 7 on page 81 to set them. Select [OK] and press <0>. A connection completion screen will appear. The main window of Camera Connect will be displayed on the smartphone.
Operating the Camera Using a Smartphone You can use a smartphone with Camera Connect installed to view images stored in the camera and shoot remotely. Camera Connect Main Window The main functions of Camera Connect are described below. Touch the screen to learn the operation procedures. [Images on camera] Images stored in the camera can be viewed. Images stored in the camera can be saved on a smartphone. Operations such as deletion can be performed on images stored in the camera.
Operating the Camera Using a Smartphone When the connection is terminated while recording a movie with remote shooting, the camera responds as follows: • When the Live View shooting/Movie shooting switch is set to , movie shooting continues. • When the Live View shooting/Movie shooting switch is set to , movie shooting stops. When the Live View shooting/Movie shooting switch is set to and the movie mode is set by operating Camera Connect, you cannot shoot by operating the camera.
Specifying Viewable Images You can specify images viewable from a smartphone by operating the camera. Images can be specified during connection setup or after the connection is terminated. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. 3 Select [Connection settings]. 4 Select [SET* Smartphone]. 5 Select [Change].
Specifying Viewable Images 6 Select [Viewable imgs]. an item. 7 Select Select [OK] and press <0> to display the setting screen. [All images] All images stored on the card become viewable. [Images from past days] Specify viewable images on the shooting-date basis. Images shot up to nine days ago can be specified. Select an item, then press <0>. When [Images shot in past days] is selected, images shot up to the specified number of days before the current date become viewable.
Specifying Viewable Images [Select by rating] Specify viewable images depending on whether a rating has been added (or not added) or by the type of rating. Select a rating, then press <0> to specify the viewable images. [File number range] (Select range) First image Last image 82 Select the first and last images from images arranged by the file number to specify the viewable images. 1 Turn the <5> dial to select the first image to be set as viewable. 2 Press <0> to display the image selection screen.
6 Linked Shooting With linked shooting, up to 10 slave cameras can be linked in a wireless network to the master camera on which you will release the shutter. Any cameras compatible with linked shooting, when they have WFT series transmitters attached, can be used as slave cameras, regardless of model. Note that there will be a slight delay after you release the master camera shutter until the slave camera shutters are released. Movie shooting is not supported.
Basic Linked Shooting Link the master camera to slave cameras for basic linked shooting. When the Live View shooting/Movie shooting switch is set to , linked shooting is not possible. Set it to . Preparing Slave Cameras First, set up slave cameras by operating the cameras to use as slaves. When using multiple slave cameras, operate all slave cameras in the same way. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings].
Basic Linked Shooting 5 Select [Connection wizard]. [Slave]. 6 Select Select [OK] and press <0> to go to the next screen. The slave cameras are now ready, with the following screen displayed. When using multiple slave cameras, set up all slave cameras to slave state. Once the settings are complete, slaves cannot be added. You must repeat the setup process from step 1.
Basic Linked Shooting Preparing the Master Camera Set up the master camera by operating the camera to use as the master. [Master]. 7 Select Perform steps 1 to 5 on page 84 for the master camera, then select [Master]. Select [OK] and press <0> to go to the next screen. [Auto connect]. 8 Select Select [OK] and press <0> to go to the next screen. To set manually, see page 91. Connecting the Cameras Operate the slave cameras and master camera to connect them. the slave cameras, select 9 On [OK].
Basic Linked Shooting all cameras, select [OK]. 11 On On the master camera and all slave cameras, select [OK]. Settings information is stored in the camera. It is not stored in the transmitter.
Positioning the Cameras Slave camera Slave camera Slave camera Slave camera Master camera Set the Live View shooting/Movie shooting switch to . Position the slave cameras in clear view of the master camera, without objects between them. Slave cameras can be positioned up to approx. 100 m / 656 ft. from the master camera.
Positioning the Cameras If focus cannot be achieved with autofocus, linked shooting is not possible with the corresponding slave camera units. Do not use multiple flash units. Although slight, there is a difference in the shutter release timing which may cause out-of-sync flash firing and inadequate exposure.
Using the Transmitter with WFT Server Using WFT Server, you can shoot remotely with a master camera linked to slave cameras set to shoot at the same time. WFT Server can also be used to access the master camera or slave cameras for Live View display, and you can adjust the focus and configure remote shooting settings as needed. Additionally, images on camera cards can be viewed and downloaded. Wireless LAN functions and operating system of the computer must support ad hoc mode.
Using the Transmitter with WFT Server Connecting the Master and Slave Cameras 1 Set up the slave cameras. Perform steps 1 to 6 on page 84 for the cameras to use as slaves. When the next screen is displayed, the slave cameras are ready. up the master camera. 2 Set Perform steps 1 to 5 on page 84 for the camera to use as the master, then select [Master]. Select [OK] and press <0> to go to the next screen. [Manual connect]. 3 Select Select [OK] and press <0> to go to the next screen.
Using the Transmitter with WFT Server the encryption key. 6 Enter Enter a 5-digit encryption key (password) and press the button. Set the key entered here on the computer in order to connect to the master camera from the computer. the slave cameras, select 7 On [OK]. On all slave cameras, select [OK]. On the master camera’s LCD monitor, the number of slave cameras detected is displayed. the master camera, select 8 On [OK]. Check the number of slave cameras, then select [OK].
Using the Transmitter with WFT Server Checking the Camera’s IP Address and SSID You will need the camera’s IP address and SSID, displayed in step 6, to connect to the camera from a computer. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. 3 Select [Connection settings]. [LinkedShot].
Using the Transmitter with WFT Server [Confirm settings]. 5 Select The settings are displayed. the settings. 6 Check Turn the <5> dial to display other screens. Write down the IP address and SSID. The SSID is the same for all the cameras. After checking the settings, press the button to exit the confirmation dialog. Check settings on the master camera and all slave cameras in the same way. IP Addresses Assigned to Computers IP addresses assigned to cameras end in 1 - 11, as in 192.168.1.
Using the Transmitter with WFT Server Connecting the Cameras and the Computer To connect the cameras and the computer, use the computer’s wireless LAN device search function. For information about the wireless LAN device search function, refer to the computer instruction manual. Wireless LAN functions and operating system of the computer must support ad hoc mode. Set up a WFT account on the [Function settings] screen (p.114) in advance. 1 From the computer, find cameras on the network.
Using the Transmitter with WFT Server Making Images Viewable and Shooting Remotely For how to use WFT Server, see page 59. To switch cameras, enter the IP address of the master or slave camera in the web browser. When shooting remotely with linked shooting, connect to the master camera. If you connect to a slave camera, only that slave camera will shoot, without linked shooting.
7 Synchronizing the Camera Time Wirelessly You can wirelessly synchronize multiple cameras of the same camera model when the transmitter is attached. You can set the master camera time on up to 10 slave cameras. Note that even after synchronization, there will be a slight margin of error between master and slave camera time of ±0.05 seconds, at most.
Synchronizing the Time Steps 1 to 5 are the same on the master and slave cameras. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. [Sync time between 3 Select cameras]. If connected to another device, [Set [Connection settings] to [Disconnect]] will appear. Select [OK] to terminate the connection. 4 Select [OK].
Synchronizing the Time [Wireless]. 5 Select Select [OK] and press <0> to go to the next screen. up the master camera. 6 Set Select [Master], then press <0>. Select [OK] and press <0> to go to the next screen. When the next screen is displayed, the master camera is ready. Go to step 7 to set up the slave cameras. up the slave cameras. 7 Set After configuring the slave camera settings following steps 1 to 5 on the preceding page, select [Slave].
Synchronizing the Time the master camera, select 8 On [OK]. Check the number of slave cameras, then select [OK]. The time on slave cameras is synchronized to the master camera time. Select [OK] to return to the [Network settings] screen.
8 Terminating the Connection and Reconnecting 101
Terminating the Connection 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. 3 Select [Connection settings]. [Disconnect]. 4 Select The connection is terminated.
Reconnecting 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. 3 Select [Connection settings]. [SET*]. 4 Select From the saved settings, select the setting to connect to. [Connect]. 5 Select The connection is re-established. If settings have been changed on the target device, configure the settings again to connect to the camera.
MEMO 104
9 Checking and Operating Connection Settings 105
Displaying the Connection Settings Screen Check, change, or delete connection settings saved on the camera. 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. 3 Select [Connection settings]. the setting. 4 Select From the saved settings, select the setting to check.
Displaying the Connection Settings Screen or change the settings. 5 Check Select an item and press <0>, then check or change the settings on the displayed screen. [Connect] (p.103) Select this to re-establish a connection. Select [OK] on the confirmation dialog and press <0> to establish a connection. [Connection wizard] Set up a connection using the connection wizard. Follow the procedures displayed to complete the connection settings. If settings are already saved, they will be overwritten.
Changing Settings Settings originally completed using the connection wizard can be changed as follows. You can also change settings that cannot be set using the connection wizard, such as when an image with the same file name as an existing file is sent to the FTP server. 1 Select [Change]. On the [Connection settings] screen displayed in step 5 on page 107, select [Change]. the item to change. 2 Select Select the item and press <0>. A setting screen will appear.
Changing Settings [FTP server] This is displayed for settings that connect to an FTP server. Configure FTP server settings. [Viewable imgs] (p.80) This is displayed for settings that connect to a smartphone. See page 80 to set. IP Security (IPsec) Configured in [TCP/IP] 9 [Security]. IPsec is a set of standards for encrypted communication over the Internet. It provides effective security for both wireless and wired LANs. To use this function, you must enable IPsec in the network settings of the computer.
Changing Settings Directory Structure of the Target Folder Configured in [FTP server] 9 [Directory structure]. Selecting [Camera] automatically creates a folder structure matching that of the camera’s (such as A/DCIM/100EOS1D) in the server’s root folder for image storage. If you have created a subfolder in the root folder by changing the [Target folder] setting, a folder structure such as “A/DCIM/100EOS1D” is automatically created in that folder for image storage.
Changing Settings Passive Mode Configured in [FTP server] 9 [Passive mode]. Enable this setting in network environments protected by a firewall. If an Error 41 occurs (“Cannot connect to FTP server”), setting passive mode to [Enable] may enable access to the FTP server.
Saving and Loading Settings Connection settings can be saved on a card for use with other cameras. In addition, connection settings configured on other cameras can be applied to the camera to be used. Saving Settings 1 Select [Save/load settings on card]. On the [Connection settings] screen displayed in step 5 on page 107, select [Save/load settings on card]. 2 Select [Save settings to card]. [OK].
Saving and Loading Settings Loading Settings 1 Select [Save/load settings on card]. On the [Connection settings] screen displayed in step 5 on page 107, select [Save/load settings on card]. 2 Select [Load settings from card]. the settings file. 3 Select Select a settings file that matches your network environment. [OK]. 4 Select Information from the settings file is loaded into the selected settings number.
Function Settings Screen On the [Function settings] screen, you can configure settings for FTP transfer and the WFT Server, set the power saving function, and check the MAC address. Displaying the Function Settings Screen 1 Select [Communication settings]. Under the [53] tab, select [Communication settings], then press <0>. [Network settings]. 2 Select Set [Communication func] to [Enable], then select [Network settings]. [Function settings]. 3 Select The [Function settings] screen is displayed.
Function Settings Screen [FTP transfer settings] Configure FTP transfer settings. See page 37 to set. [WFT server settings] Configure WFT Server settings. You can set the WFT account and port number. For instructions on setting the WFT account, see page 60. Note that there is normally no need to change the port number (80).
Function Settings Screen [Power saving] FTP Trans. When [Enable] is set, if no image is transferred for a certain period of time, the transmitter will log off from the FTP server and stop the LAN. When the transmitter is ready for image transfer, the connection is re-established automatically. EOSUtility/WFTserver/Smartphone If no communication is established for a certain period of time, the transmission rate drops to save power.
10 Troubleshooting Guide Transfer speed in ad hoc mode may become extremely slow when the transmitter is used with certain types of computer. For more information, contact your dealer or nearest Canon Service Center.
Responding to Error Messages If a wireless setting error is displayed on the camera’s LCD monitor, refer to the examples of corrective actions in this section to eliminate the cause of the error. In case of errors, the lamp on the camera blinks in red. The error details can also be checked under the [53] tab [Communication settings] 9 [Network settings] 9 [Error description]. Click the error code number’s page in the following chart to jump to the corresponding page. 11 (p.119) 12 (p.119) 21 (p.
Responding to Error Messages 11: Connection target not found In the case of [EOSUtility], is EOS Utility running? Start EOS Utility and re-establish the connection (p.56). In the case of [Smartphone], is Camera Connect running? Establish a connection using Camera Connect (p.76).
Responding to Error Messages What to check on the DHCP server Is the power of the DHCP server on? Turn on the DHCP server. Are there enough addresses for assignment by the DHCP server? Increase the number of addresses assigned by the DHCP server. Remove devices assigned addresses by the DHCP server from the network to reduce the number of addresses in use. Is the DHCP server working correctly? Check the DHCP server settings to make sure it is working correctly as a DHCP server.
Responding to Error Messages 22: No response from DNS server What to check on the transmitter On the transmitter, DNS address is set to [Manual setting]. Is this the correct setting? If no DNS server is used, set the transmitter’s DNS address setting to [Disable] (p.144). On the transmitter, does the DNS server’s IP address setting match the server’s actual address? On the transmitter, set the IP address that matches the address of the DNS server used (p.138, 144).
Responding to Error Messages 23: Duplicate IP address What to check on the transmitter Is another device on the transmitter network using the same IP address as the transmitter? Change the transmitter’s IP address to avoid using the same address as another device on the network. Otherwise, change the IP address of the device that has a duplicate address. If the transmitter’s IP address is set to [Manual setting] in network environments using a DHCP server, change the setting to [Auto setting] (p.34).
Responding to Error Messages What to check on the proxy server Is the power of the proxy server on? Turn on the proxy server. Is the proxy server working correctly? Check the proxy server settings to make sure it is working correctly as a proxy server. If applicable, ask your network administrator for the proxy server’s address setting and port number, then enter them on the transmitter.
Responding to Error Messages 41: Cannot connect to FTP server What to check on the transmitter On the transmitter, does the FTP server’s IP address setting match the server’s actual address? Configure the IP address on the transmitter to match the actual FTP server address (p.38). Are the transmitter and the access point set to use the same encryption key for authentication? This error occurs if the encryption keys do not match when the authentication method for encryption is set to [Open system].
Responding to Error Messages What to check on the FTP server Is the FTP server working correctly? Configure the computer correctly to function as an FTP server. If applicable, ask your network administrator for the FTP server address and port number, then enter them on the transmitter. Is the power of the FTP server on? Turn on the FTP server. The server may have been turned off because of an energy-saving mode.
Responding to Error Messages What to check on the network as a whole Does your network include a router or similar device that serves as a gateway? If applicable, ask your network administrator for the network gateway address and enter it on the transmitter (p.138, 144). Make sure that the gateway address setting is correctly entered on all network devices, including the transmitter.
Responding to Error Messages 45: Cannot login to FTP server. Error code received from server. What to check on the transmitter On the transmitter, is the [Login name] entered correctly? Check the login name for accessing the FTP server. The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct login name is entered on the transmitter (p.39).
Responding to Error Messages 46: For the data session, error code received from FTP server What to check on the FTP server The connection was terminated by the FTP server. Restart the FTP server. Do the user rights for the FTP server allow reading, writing, and log access? Configure the FTP server’s user rights to allow reading, writing, and log access.
Responding to Error Messages 61: Selected SSID wireless LAN network not found Are any obstacles blocking the line of sight between the transmitter and the antenna of the access point? Move the antenna of the access point to a position clearly visible from the point of view of the transmitter (p.136). What to check on the transmitter Does the SSID set on the transmitter match that of the access point? Check the SSID at the access point, then set the same SSID on the transmitter (p.31).
Responding to Error Messages 63: Wireless LAN authentication failed Are the transmitter and the access point set to use the same authentication method? The transmitter supports the following authentication methods: [Open system], [Shared key], and [WPA/WPA2-PSK] (p.27). Are the transmitter and the access point set to use the same encryption key for authentication? The setting is case-sensitive, so check upper- and lower-case characters.
Responding to Error Messages 65: Wireless LAN connection lost Are any obstacles blocking the line of sight between the transmitter and the antenna of the access point? Move the antenna of the access point to a position clearly visible from the point of view of the transmitter (p.136). The wireless LAN connection was lost, for some reason, and the connection cannot be restored.
Responding to Error Messages 67: Incorrect wireless LAN encryption method Are the transmitter and the access point set to use the same encryption method? The transmitter supports the following encryption methods: WEP, TKIP, and AES (p.27). If filtering by MAC address is active, is the MAC address of the transmitter used registered at the access point? Register the MAC address (p.116) of the transmitter used at the access point. 68: Cannot connect to wireless LAN terminal. Retry from the beginning.
Responding to Error Messages 71: Cannot connect to slave camera Are you following the correct procedure to establish the connection with slave cameras? Operate slave cameras by following the correct instructions (p.84, 85). Are the slave cameras too far from the master camera? Bring the slave cameras closer to the master camera.
Responding to Error Messages 82: Wireless File Transmitter not connected Is the transmitter attached correctly? Make sure the transmitter is securely inserted in the camera (p.11). 83: Wireless LAN connection terminated because of high WFT temperature Due to transmitter temperature rise, wireless operation has temporarily stopped and the wireless LAN connection has been terminated. Allow the transmitter to cool down (for example, by shielding it from direct sunlight).
Troubleshooting Guide If a problem occurs, first refer to this Troubleshooting Guide to check the camera and connected device. If this Troubleshooting Guide does not resolve the problem, contact the nearest Canon Service Center. Cannot transfer images to an FTP server. To transfer captured images to an FTP server, set the Live View shooting/Movie shooting switch to . When the Live View shooting/Movie shooting switch is set to , images cannot be transferred. Cannot perform linked shooting.
Communication Function Setting Notes If the transmission rate drops, the connection is lost, or other problems occur when using the communication function, try the following corrective actions. Access Point and Antenna Installation Location When using the transmitter indoors, install the device in the same room where you are shooting. Install the device higher than the transmitter. Install the device where people or objects do not come between it and the transmitter.
Communication Function Setting Notes Notes for Using Multiple Wireless Transmitters When multiple cameras with a wireless transmitter attached are connected to one access point, make sure that the cameras’ IP addresses are different. When multiple cameras with a wireless transmitter attached are connected to one access point, the transmission rate drops. When there are multiple IEEE 802.11n/g/b (2.
Checking Network Settings Windows Open the Windows [Command Prompt], then type ipconfig /all and press the key. The IP address assigned to the computer is displayed, as well as the subnet mask, gateway, and DNS server information. Mac OS In Mac OS X, open the [Terminal] application, enter ifconfig -a, and press the key. The IP address assigned to the computer is indicated in the [en0] item by [inet], in the format “***.***.***.***”.
11 Reference 139
Creating and Registering Captions Follow these steps to create captions and register them on the camera, as introduced in “Adding a Caption Before Transfer” (p.52). When creating and registering captions, use a computer on which EOS Utility is installed. See “Operating Remotely Using EOS Utility” on page 55 to enable the use of EOS Utility over a LAN. 1 Start EOS Utility and select [Camera settings]. The camera settings screen is displayed. [WFT Captions].
Creating and Registering Captions the caption or captions. 3 Enter Enter up to 31 characters (in ASCII format). To acquire caption data stored in the camera, select [Load settings]. the captions on the 4 Register camera. Select [Apply to camera] to register your new captions on the camera.
Setting Network Manually Set the network settings for the camera access point mode manually. Set [SSID], [Channel setting], and [Encryption settings] on each screen displayed. 1 Select [Manual connection]. Select [OK] and press <0> to go to the next screen. an SSID (network name). 2 Enter Enter any characters using the virtual keyboard (p.21). When you are finished, press the button. the desired channel 3 Select setting.
Setting Network Manually the desired encryption 4 Select setting. For encryption, select [AES]. Select [OK] and press <0>. When [AES] is selected, the virtual keyboard (p.21) is displayed. Enter any encryption key of eight characters, then press the button to set. The set SSID and encryption key are displayed. For subsequent operations, see “Connecting with Easy Connection” (p.25).
Setting IP Address Manually Set the IP address settings manually. The items displayed will differ depending on the communication method. 1 Select [Manual setting]. Select [OK] and press <0> to go to the next screen. the item to be set. 2 Select Select an item and press <0>. The number entry screen will appear. To use a gateway, DNS address, or IPsec, select [Enable], select [Address], then press <0>. the desired values.
Setting IP Address Manually [OK]. 4 Select When you have completed setting the necessary items, select [OK] and press <0>. The setting screen for the communication method will appear. If you are not sure what to enter, see “Checking Network Settings” (p.138), or ask the network administrator or another person knowledgeable about the network.
Specifications 9Type Type: IEEE 802.11n/a/g/b wireless LAN compatible image transfer accessory 9Wireless LAN Standards compliance: IEEE 802.11n, IEEE 802.11a, IEEE 802.11g, IEEE 802.11b Transmission method: DS-SS modulation (IEEE 802.11b) OFDM modulation (IEEE 802.11n/a/g) Transmission range: Up to approx. 150 m / 492 ft. * With no obstructions between the transmitting and receiving antennas and no radio interference * Up to 15 m / 49.2 ft.
Specifications 9LAN Functions FTP transfer: Automatic transfer Image selection and transfer Transfer using SET button Transfer with captions * FTPS supported EOS Utility remote control functions over wireless LAN EOS Utility: WFT Server: Camera control, Simple control Image viewing and downloading Smartphone: Images can be viewed, controlled, and received using a smartphone. Remote control of the camera using a smartphone is possible.
Trademarks Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. The Wi-Fi CERTIFIED logo and the Wi-Fi Protected Setup mark are trademarks of the Wi-Fi Alliance. WPS used on camera settings screens and in this manual stands for Wi-Fi Protected Setup. UPnP is a trademark of the UPnP Implementers Corporation.
Index A Account (WFT)........................60, 115 Ad hoc.............................................91 AES.................................................27 Area of use ............ Areas of Use and Restrictions Authentication .........................27, 109 Auto power off.................................22 Automatic image transfer ................43 B Batch transfer..................................48 Browsers ...................................15, 63 C Camera access point mode ............
Index Password ........................................60 PBC mode ......................................28 PIN code connection mode.............29 PIN mode........................................29 Port number ....................................39 Power saving ................................116 Proxy server....................................39 Pushbutton connection mode .........28 R RAW ...............................................46 RAW+JPEG ....................................46 Reconnecting.....
MEMO 151
The descriptions in this Instruction Manual are current as of June 2016. For information on the compatibility with any products introduced after this date, contact any Canon Service Center. For the latest version Instruction Manual, refer to the Canon Web site. CPA-E198-001 © CANON INC.
