INSTRUCTION MANUAL E E INSTRUCTION MANUAL
Thank you for purchasing a Canon product. The EOS 20D is a high-performance, digital AF SLR camera with a large, fine-detail, 8.20-megapixel CMOS sensor. The camera has nine high-precision AF points and it is compatible with all Canon EF lenses (including the EF-S lens). Designed for quick shooting at anytime, the camera has many features for all types of photography, from fully automatic snapshooting to professional-level, creative work.
Item Check List Check that all the following items have been included with your camera. If anything is missing, contact your dealer. ¢ EOS 20D / Camera body (with Eyecup, body cap and lithium backup battery for the date and time) ¢ ¢ ¢ ¢ ¢ ¢ ¢ EF-S18-55mm f/3.5-5.6 / Lens (with lens cap and dust cap) * Lens kit only. Battery Pack BP-511A (with protective cover) Battery Charger CG-580/CB-5L * CG-580 or CB-5L is included. Power code for battery charger * For CB-5L.
Contents Introduction Item Check List..................................................................................................3 Handling Precautions ........................................................................................8 Nomenclature ..................................................................................................10 Conventions Used in this Manual ....................................................................
Contents Focusing an Off-Center Subject ...................................................................... 69 When Autofocus Fails (Manual Focusing)....................................................... 70 Selecting the Metering Mode........................................................................... 71 Selecting the Drive Mode ................................................................................
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
Handling Precautions Camera Care ¡ This camera is a precision instrument. Do not drop it or subject it to physical shock. ¡ The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe with a well-wrung wet cloth.
Handling Precautions LCD Panel and LCD Monitor ¡ Although the LCD monitor is manufactured with very high precision technology with over 99.99% active pixels, there might be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying only black or red, etc., are not a malfunction. They do not affect the images recorded. ¡ At low temperatures, the liquid-crystal display response may become slower. And at high temperatures, the display may blacken.
Nomenclature For detailed information, reference page numbers are provided in parentheses (p.**). AF mode selection/ White balance selection button (p.64/50) Drive mode selection/ISO speed button (p.72/49) Metering mode selection/Flash exposure compensation button (p.71/96) <6> Main Dial (p.27) LCD panel illumination button (p.89) LCD panel (p.12) EF Lens mount index (p.23) Built-in flash/AF-assist beam (p.92/68) EF-S Lens mount index (p.23) Flash-sync contacts Hot shoe (p.
Nomenclature Dioptric adjustment knob (p.38) Eyecup (p.89) Viewfinder eyepiece Menu button (p.29) <9> Multi-controller (p.28) AE lock/ FE lock button/Index/ Reduce button (p.86/95/105/106,129) AF point selection/ Enlarge button (p.67/106,129) Info/ Trimming orientation button (p.62,103/129) Strap mount (p.17) Jump button (p.107) Playback button (p.103) CF card slot cover (p.24) Erase button (p.112) Battery compartment cover release lever (p.20) LCD monitor (p.
Nomenclature LCD Panel Shutter speed Busy (buSY) Built-in flash recycling (buSY) ISO speed gISO speed White balance Q Auto W Daylight E Shade R Cloudy Y Tungsten light U White fluorescent light I Flash O Custom P Color temperature AF point selection ([ - -- --- -- - ]) CF card full warning (FuLL CF) CF card error warning (Err CF) No CF card warning (no CF) Error code (Err) Cleaning image sensor (CLEA n) Processing Parameters (PA- P1 / P2 / 1 / 2 / 3) Aperture Shots remaining Shots remaining during WB brac
Nomenclature Viewfinder Information Partial metering circle Focusing screen AF points (Superimposed display) Focus confirmation light AE lock/FE lock AEB in-progress Max.
Nomenclature Mode Dial The Mode Dial is divided into two function zones. Creativ e zo n e Full Auto ne I m a g e zo ne zo c i Bas q Basic Zone All you do is press the shutter button. 1 : Full Auto (p.40) For fully automatic shooting. Image Zone Allows you fully automatic shooting for specific subjects. 2 : Portrait (p.42) 3 : Landscape (p.42) 4 : Close-up (p.42) 5 : Sports (p.43) 6 : Night Portrait (p.43) 7 : Flash Off (p.43) 14 w Creative Zone Set the camera as you wish. d : Program AE (p.
Nomenclature Battery Charger CG-580 This is a battery pack charger. (p.18) Power plug Battery pack slot Red lamp Battery Charger CB-5L This is a battery pack charger. (p.
Conventions Used in this Manual ¡In the text, the <4> icon indicates the power switch. ¡All operations described in this manual assume that the <4> switch is set to <1> or . 6 5 ¡The <6> icon indicates the Main Dial. ¡The <5> icon indicates the Quick Control Dial. ¡Operations with the <5> dial assume that the <4> switch is already set to . Be sure it is set to . 9 ¡In the text, the <9> icon indicates the Multi-controller. 0 ¡In the text, the <0> icon indicates the SET button.
1 Getting Started This chapter explains a few preliminary steps and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. ¡ The eyepiece cover is also attached to the strap. (p.
Recharging the Battery For details on the battery, refer to the instructions for Battery Pack BP-511A. 1 Remove the cover. ¡ When you remove the battery from the camera, be sure to reattach the cover to protect against short circuit. the battery. 2 Attach ¡ Align the battery front edge with the <–> mark CG-580 <–> mark on the battery charger. While pressing down the battery, slide it in the direction of the arrow. ¡ To detach the battery, follow the above procedure in reverse.
Recharging the Battery Recharge Level 0-50% 50-75% ¡ The numbers and markings on the battery charger correspond to the table on the left. Blinks twice per second Red lamp Blinks once per second 75-90% Blinks three times per second 90% or higher Lights on ¡ Do not recharge any battery pack other than Battery Pack BP-511A, BP514, BP-511, or BP-512.
Installing and Removing the Battery Installing the Battery Load a fully charged BP-511A battery pack into the camera. 1 Open the battery compartment cover. ¡ Slide the lever as shown by the arrow and open the cover. the battery. 2 Insert ¡ Point the battery contacts downward. ¡ Insert the battery until it locks into place. the cover. 3 Close ¡ Press the cover until it snaps shut. Battery Pack BP-514, BP-511, or BP-512 can also be used.
Installing and Removing the Battery Battery Life Temperature [Number of shots] Shooting Conditions No Flash 50% Flash Use At 20°C / 68°F Approx. 1000 Approx. 700 At 0°C / 32°F Approx. 750 Approx. 550 ¡ The figures above are based on a fully-charged BP-511A and CIPA (Camera & Imaging Products Association) testing criteria. ¡ The actual number of shots may be fewer than indicated above depending on the shooting conditions.
Using a Household Power Outlet With AC Adapter Kit ACK-E2 (optional), you can connect the camera to a household power outlet and not worry about the battery level. 1 Connect the DC Coupler. ¡ Connect the DC Coupler’s plug to the AC adapter’s socket. the power cord. 2 Connect ¡ Connect the power cord to the AC adapter. ¡ Insert the plug into a power outlet. ¡ When you are finished, disconnect the plug from the power outlet. the cord in the groove.
Mounting and Detaching a Lens Mounting a Lens 1 EF-S Lens mount index EF lens mount index Remove the caps. ¡ Remove the rear lens cap and the body cap by turning them as shown by the arrow. the lens. 2 Attach ¡ Align the EF-S lens with the camera’s white EF-S lens mount index and turn the lens as shown by the arrow until it clicks in place. ¡ When attaching a lens other than an EF-S lens, align the lens with the red EF lens index mark. the lens, set the focus mode 3 On switch to .
Installing and Removing the CF Card The captured image will be recorded onto the CF card (optional). Although the thickness is different, a Type I or Type II CF card can be inserted into the camera. The camera is also compatible with Microdrive and CF cards with 2 GB or higher capacity. Installing the Card 1 Open the cover. ¡ Slide the cover as shown by the arrow to open it. the CF card. 2 Insert ¡ Using Canon CF cards is Top CF card eject button recommended.
Installing and Removing the CF Card Removing the CF Card 1 Access lamp Open the cover. ¡ Turn the <4> switch to <2>. ¡ Check that the “buSY” message is not displayed on the LCD panel. ¡ Make sure the access lamp is off, then open the cover. the CF card. 2 Remove ¡ Press the Eject button. s The CF card will be ejected. ¡ Close the cover. ¡ A blinking access lamp indicates that data is being read, written, or erased on the CF card or that data is being transferred.
Basic Operation Power Switch The camera can operate only after the <4> switch is turned on. <2>: The camera is turned off and does not operate. <1> : The camera operates. : The camera and <5> operate. (p.28) ¡ To save battery power, the camera turns off automatically after 1 minute of non-operation. To turn on the camera again, just press the shutter button. ¡ You can change the auto power-off time with the menu’s [c Auto power off] setting. (p.
Basic Operation ¡ If you press the shutter button halfway and (0) elapse, you must press it halfway again and wait a moment before pressing it completely to take a picture. If you press the shutter button completely without pressing it halfway first or if you press the shutter button halfway and then press it completely immediately, the camera will take a moment before it takes the picture. ¡ No matter what state the camera is in (image playback, menu operation, image recording, etc.
Basic Operation Operating the <5> Dial The <5> dial is mainly used for shooting-related settings and selecting LCD monitor items. When you want to use the <5> dial to prepare for shooting, set the <4> switch to first. (1) After pressing a button, turn the <5> dial. When you press a button, its function remains active for 6 seconds (9). During this time, you can turn the <5> dial to set the desired setting.
Menu Operations By setting various optional settings with the menus, you can set the image recording quality, processing parameters, the date/time, Custom Functions, etc. While looking at the LCD monitor, you use the button, <0> button, and <5> dial on the camera back to proceed to the next step. LCD Monitor button <5> Quick Control Dial button <0> button Menu category color code Menu category Menu settings Menu items The menu screen is color coded for the three menu categories.
Menu Operations Menu Setting Procedure 1 Display the menu. ¡ Press the button to display the menu. To turn off the menu, press the button again. a menu item. 2 Select ¡ Turn the <5> dial to select the menu item, then press <0>. ¡ Press the button to jump to the first item of each menu category. the menu setting. 3 Select ¡ Turn the <5> dial to select the desired setting. the desired setting. 4 Set ¡ Press <0> to set it. the menu. 5 Exit ¡ Press the button to exit the menu display.
Menu Operations Menu Settings Shooting menu (Red) Quality 73/83/74/84/76/86/ RAW/ RAW+73/ +83/ +74/ +84/ +76/ +86 Red-eye On/Off Beep Shoot w/o card AEB WB SHIFT/BKT Custom WB Color temp.
Menu Operations About the LCD Monitor ¡ When using the LCD monitor, you can use the <5> dial even while the <4> switch is <1>. ¡ The LCD monitor cannot be used as a viewfinder for shooting. ¡ You can adjust the brightness of the LCD monitor to one of five levels. (p.102) Restoring the Camera’s Default SettingsN 1 Select [Clear settings]. ¡ Press the button. ¡ Turn the <5> dial to select [c Clear settings], then press <0>. [Clear all camera settings].
3Setting the Language The LCD monitor’s interface language can be set to one of twelve languages. 1 Select [Language]. ¡ Turn the <5> dial to select [c Language], then press <0>. s The Language screen will appear. the desired language. 2 Set ¡ Turn the <5> dial to select the langauge, then press <0>. s The language will change.
3Setting the Date and Time Set the date and time as shown below. 1 Select [Date/Time]. ¡ Turn the <5> dial to select [c Date/ Time], then press <0>. s The date/time screen will appear. the date and time. 2 Set ¡ Turn the <5> dial to select the digit, then press <0>. ¡ The selection will then shift to the next item. the date display format. 3 Set ¡ Turn the <5> dial to set the date format to [mm/dd/yy], [dd/mm/yy], or [yy/mm/dd]. <0>. 4 Press s The date and time will be set and the menu will reappear.
Replacing the Date/Time Battery The date/time (back-up) battery maintains the camera’s date and time. The battery’s service life is about 5 years. If the date/time is reset when the battery is replaced, replace the back-up battery with a new CR2016 lithium battery as described below. The date/time setting will also be reset, so you must set the correct date/time. 1 Turn the <4> switch to <2>. the cover and remove the 2 Open battery. 3 Take out the battery holder.
3 Cleaning the CMOS sensorN The image sensor is like the film in a film camera. If any dust or other foreign matter adheres to the image sensor, it may show up as a dark speck in the images. To avoid this, follow the procedure below to clean the image sensor. Note that the image sensor is a very delicate component. If possible, you should have it cleaned by a Canon Service Center. While you clean the image sensor, the camera must be turned on.
3 Cleaning the CMOS sensorN the image sensor. 4 Clean ¡ Use a rubber blower to carefully blow away any dust, etc., on the surface of the image sensor. the cleaning. 5 Stop ¡ Turn the <4> switch to <2>. s The camera will turn off, the shutter will close, and the mirror will go back down. ¡ Set the <4> switch to <1>. The camera will then be ready to shoot. ¡ During the sensor cleaning, never do any of the following that would turn off the power.
Dioptric Adjustment By adjusting the diopter to suit your eyesight, you can see a sharp viewfinder image even without eyeglasses. The camera’s adjustable dioptric range is -3 to +1 dpt. Turn the dioptric adjustment knob. ¡ Turn the knob left or right so that the AF points in the viewfinder look sharp. ¡ The illustration shows the knob at the standard setting (-1 dpt).
2 Fully Automatic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for quick and easy shooting. In each mode <1> <2> <3> <4> <5> <6> <7>, the AF mode, drive mode, etc., are set automatically to suit the subject. In these modes, all you do is point and shoot. In addition, to help prevent mistakes caused by operating the camera improperly, the buttons and <9> are disabled in these modes. So you need not worry about accidental errors.
1Using Full Auto All you do is point the camera and press the shutter button. Everything is automatic so it is easy to photograph any subject. With nine AF points to focus the subject, anyone can easily take nice pictures. 1 AF point Set the Mode Dial to <1>. s Automatically, the AF mode will be set to <9>, the drive mode will be set to , and the metering mode will be set to . any AF point on the subject.
1Using Full Auto the picture. 5 Take ¡ Compose the shot and press the shutter button completely. s The captured image will be displayed for about 2 sec. on the LCD monitor. ¡ To view the images recorded on the CF card, press the button. (p.103) ¡ While focusing with , do not touch the focusing ring at the front of the lens. ¡ If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus.
Basic Zone Modes Select a shooting mode to suit the target subject, and the camera will be set to obtain the best results. 2 Portrait This mode blurs the background to make the human subject stand out. ¡ Holding down the shutter button executes continuous shooting. ¡ To improve the background blur, use a telephoto lens and fill the frame with the subject. Or have the subject stand farther away from the background.
Basic Zone Modes 5 Sports This is for fast-moving subjects when you want to freeze the action. ¡ The camera will first track the subject with the center AF point. Focus tracking will then continue with any of the nine AF points covering the subject. ¡ While you press the shutter button, focusing will continue for continuous shooting. ¡ Using a telephoto lens is recommended. ¡ When focus is achieved, the beeper will sound softly.
jSelf-timer Operation Use the self-timer when you want to be in the picture. You can use selftimer in any Basic Zone mode or Creative Zone mode. 1 Press the button. (9) . 2 Select ¡ Look at the LCD panel and turn the <6> dial to select . the subject. 3 Focus ¡ Look in the viewfinder and press the shutter button halfway to check that the focus confirmation light is on and the exposure setting is displayed. the picture. 4 Take ¡ Look through the viewfinder and press the shutter button completely.
3 Image Settings This chapter explains the digital image settings for the image-recording quality, ISO speed, white balance, color space, and processing parameters. ¡ For Basic Zone modes, only the image-recording quality (except RAW and RAW+JPEG), file numbering, and camera setting check will apply in this chapter. ¡ The asterisk M on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8).
3 Setting the Image-recording Quality The 73/83/74/84/76/86 modes record the image in the widely-used JPEG format. In the 1 mode, the captured image will require post-processing with the software provided. The 1+73/ +83/+74/+84/+76/+86 (RAW+ JPEG) modes simultaneously record the image in both RAW and JPEG formats. Note that in the Basic Zone modes, the RAW and RAW+JPEG formats cannot be selected. 1 Select [Quality]. ¡ Turn the <5> dial to select [z Quality], then press <0>.
3 Setting the Image-recording Quality About the RAW Format The RAW format assumes that the image will undergo post-processing with a personal computer. Special knowledge is required, but you can use the bundled software to obtain the desired effect. <1> images are processed according to the white balance, color space, and processing parameters set at the time of shooting. Image processing refers to adjusting the RAW image’s white balance, contrast, etc., to create the final image.
3 Setting the Image-recording Quality Max. Burst During Continuous Shooting The maximum burst during continuous shooting depends on the imagerecording quality. The approx. maximum burst during continuous shooting is indicated below for each image-recording quality. Note that with high-speed CF cards, the maximum burst may be higher than shown in the table below depending on the shooting conditions. (With the recording quality set to JPEG.) Image-recording quality Max.
g Setting the ISO SpeedN The ISO speed is a numeric indication of the sensitivity to light. A higher ISO speed number indicates a higher sensitivity to light. Therefore, a high ISO speed is suited for low light and moving subjects. However, the image may look more coarse with noise, etc. On the other hand, a low ISO speed is not suited for low light or action shots, but the image will look cleaner. The camera can be set between ISO 100 and 1600 in 1stop increments.
B Setting the White BalanceN Normally, the setting will set the optimum white balance automatically. If natural-looking colors cannot be obtained with , you can set the white balance manually to suit the respective light source. In the Basic Zone modes, will be set automatically. 1 Press the button. (9) the white balance setting. 2 Select ¡ While looking at the top LCD panel, turn the <5> dial. Display Q Mode Auto Color temperature (Approx.
3 Custom White BalanceN With custom white balance, you shoot a white object that will serve as the basis for the white balance setting. By selecting this image, you import its white balance data for the white balance setting. 1 Press the button. (9) the custom white balance. 2 Select ¡ Look at the LCD panel and turn the <5> dial to select . a white object. 3 Photograph ¡ The plain, white object should fill the Partial metering partial metering circle.
3 Custom White BalanceN ¡ If the exposure obtained in step 3 is underexposed or overexposed, a correct white balance might not be obtained. ¡ If an image was captured while the processing parameter was set to [B/ W] (p.59), it cannot be selected in step 5. Instead of a white object, an 18% gray card (commercially available) can produce a more accurate white balance. 3 Setting the Color TemperatureN You can numerically set the white balance’s color temperature. 1 Press the button.
3 White Balance CorrectionN You can correct the standard color temperature for the white balance setting. This adjustment will have the same effect as using a color temperature conversion or color compensating filter. Each color can be corrected to one of nine levels. Users familiar with using color temperature conversion or color compensating filters will find this feature handy. 1 Select [WB SHIFT/BKT]. ¡ Turn the <5> dial to select [z WB SHIFT/BKT], then press <0>.
3 White Balance Auto BracketingN With just one shot, three images having a different color tone can be recorded simultaneously. Based on the white balance mode’s standard color temperature, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing. It can be set up to ±3 levels in single-level increments. 1 Set the image-recording quality to any setting except RAW and RAW+JPEG. (p.46) [WB SHIFT/BKT].
3 White Balance Auto BracketingN the picture. 4 Take s When B/A bracketing has been set, the three images will be recorded onto the CF card in the following sequence: Standard WB, B (blue) bias, and A (amber) bias. If M/G bracketing has been set, the sequence will be Standard WB, M (magenta) bias, and G (green) bias. ¡ The current drive mode (p.72) will be used for the shooting. Canceling White Balance Auto Bracketing ¡ In step 3, set “BKT” to “±0” (“ “ ” (1 point)).
3 Setting the Color SpaceN The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal images, sRGB is recommended. In the Basic Zone modes, sRGB will be set automatically. 1 Select [Color space]. ¡ Turn the <5> dial to select [z Color space], then press <0>. the desired color space. 2 Set ¡ Turn the <5> dial to select [sRGB] or [Adobe RGB], then press <0>.
3 Selecting the Processing ParametersN The image you capture can be processed to look more vivid and sharp or more subdued. The processing parameters can be set according to the preset Parameter 1 or Parameter 2 or to Set 1, 2, or 3 that you can set yourself. Monochrome can also be set. In the Basic Zone modes, Parameter 1 will be set automatically. 1 Select [Parameters]. ¡ Turn the <5> dial to select [z Parameters], then press <0>. s Processing parameter setting screen will appear. 2 Press <0>.
3 Setting the Processing ParametersN The image you capture can be processed automatically by the camera in accordance with the parameter settings you set (five settings each for [Contrast], [Sharpness], [Saturation], and [Color tone]). You can register and save up to three sets of processing parameters. 1 Select [Parameters]. ¡ Turn the <5> dial to select [z Parameters], then press <0>. s Processing parameter setting screen will appear. 2 Press <0>. the set number.
3 Setting the Processing ParametersN Black-and-White Shooting When you capture images with the processing parameter set to Monochrome, the camera will process and record the images as blackand-white images onto the CF card. 1 Select [B/W]. ¡ In step 3 on page 58, select [B/W], then press <0>. the item to be set. 2 Select ¡ Turn the <5> dial to select the menu item, then press <0>. ¡ The [Contrast] and [Sharpness] will be the same as in the table in step 4 on page 58.
3 Setting the Processing ParametersN Filter effects The same effect as using filters with black-and-white film can be obtained with digital images. A color can be brightened by using a filter having a similar or same color. At the same time, the complementary colors will be darkened. Filter Sample effects N: None Normal black-and-white image with no filter effects. Ye: Yellow The blue sky will look more natural, and the white clouds will look clearer. Or: Orange The blue sky will look slightly darker.
3 File Numbering Methods The file number is like the frame number on film. There are two file numbering methods: [Continuous] and [Auto reset]. The images you take are automatically assigned a file number from 0001 to 9999 and saved in a folder (created automatically) that can hold up to 100 images. 1 Select [File numbering]. ¡ Turn the <5> dial to select [c File numbering], then press <0>. the file numbering method. 2 Select ¡ Turn the <5> dial to select [Continuous] or [Auto reset], then press <0>.
B Checking Camera Settings When the camera is ready to shoot, press the button to view the current camera settings on the LCD monitor. Display the camera settings. ¡ Press the button. s The current camera settings appear on the LCD monitor. ¡ To turn off the LCD monitor, press the button again. Camera Setting Display Date/Time (p.34) AEB setting (p.84) WB correction (p.53)/ WB bracketing (p.54) Color space (p.56) Processing parameters (p.57) Image review time (p.
4 Setting the AF, Metering, and Drive Modes Drive modes AF mode Metering mode The viewfinder has 9 AF points. By selecting a suitable AF point, you can shoot with autofocus while framing the subject as desired. You can also set the AF mode to suit the subject or obtain the desired effect. Evaluative, partial, and centerweighted average metering modes are provided. Single, continuous, and Self-timer drive modes are provided. Select the metering mode that suits the subject or your photographic intention.
f Selecting the AF ModeN The AF mode is the autofocusing operation method. Three AF modes are provided. One-Shot AF is suited for still subjects, while AI Servo AF is for moving subjects. And AI Focus AF switches from One-Shot AF to AI Servo AF automatically if the still subject starts moving. In the Basic Zone modes, the optimum AF mode is set automatically. 1 On the lens, set the focus mode switch to . the Mode Dial to a Creative 2 Set Zone mode. 3 Press the button. (9) the AF mode.
f Selecting the AF ModeN One-Shot AF for Still Subjects Pressing the shutter button halfway activates the autofocus and achieves focus once. AF point Focus confirmation light s The AF point which achieves focus flashes briefly. At the same time, the focus confirmation light in the viewfinder is displayed. s With evaluative metering, the exposure setting (shutter speed and aperture) will be set when focus is achieved.
f Selecting the AF ModeN * About Predictive AF If the subject approaches or retreats from the camera at a constant rate, the camera tracks the subject and predicts the focusing distance immediately before the picture is taken. This is for obtaining correct focus at the moment of exposure. ¡ When the AF point selection is automatic, the camera first uses the center AF point to focus.
SSelecting the AF PointN The AF point is used for focusing. The AF point can be selected automatically by the camera or manually by you. Automatic AF point selection is set in the Basic Zone modes and 8>. In the modes, you can switch <8 between automatic and manual AF point selection. Automatic AF point selection The camera selects the AF point automatically according to the shooting conditions. All the AF points in the viewfinder will light in red.
SSelecting the AF PointN Selecting with the Dial ¡ Press the and turn the <6> or <5> dial. ¡ When you turn the dial, the selection will go in the looping sequence shown on the left. ¡ When looking at the LCD panel to select the AF point, note the following: Automatic selection , center , right , top ¡ If focus cannot be achieved with an EOS-dedicated, external Speedlite’s AF-assist beam, select the center AF point.
Focusing an Off-Center Subject After achieving focus, you can lock the focus on a subject and recompose the shot. This is called “focus lock.” Focus lock works only in the One-Shot AF mode. the Mode Dial to a Creative 1 Set Zone mode. 2 Select the desired AF point. the subject. 3 Focus ¡ Move the AF point over the subject and press the shutter button halfway. pressing the shutter button 4 Keep halfway and recompose the picture as desired. 5 Take the picture.
When Autofocus Fails (Manual Focusing) Autofocus can fail to achieve focus (the focus confirmation light blinks) with certain subjects such as the following: Subjects difficult to focus (a) Low-contrast subjects Example: Blue sky, solid-color walls, etc. (b) Subjects in low light. (c) Extremely backlit and reflective subjects Example: Car with a reflective body, etc. (d) Overlapping near and far objects Example: Animal in a cage, etc.
qSelecting the Metering ModeN The camera has three metering modes: Evaluative, partial, and centerweighted average metering. In the Basic Zone modes, evaluative metering will be set automatically. 1 Press the button. (9) the metering mode. 2 Select ¡ While looking at the LCD panel, turn the <6> dial. q: Evaluative Metering w: Partial Metering e: Centerweighted Average Metering q Evaluative Metering This is the camera’s standard metering mode suited for most subjects even under backlit conditions.
iSelecting the Drive Mode Single and continuous drive modes are provided. In the Basic Zone modes, the optimum drive mode is set automatically. 1 Press the button. (9) the drive mode. 2 Select ¡ While looking at the LCD panel, turn the <6> dial. u : Single shooting When you press the shutter button completely, one shot will be taken. i : Continuous shooting (Max. 5 shots per sec.) While you press the shutter button completely, shots will be taken continuously. j : Self-timer Operation (p.
5 Advanced Operations Cre ati v e ne zo With Creative Zone modes, you can set the desired shutter speed or aperture value to obtain the result you want. You take control of the camera. ¡ The asterisk M on the right of the page title indicates that the respective feature is available only in Creative Zone modes (d, s, f, a, 8). ¡ After you press the shutter button halfway and let go, the timer operation will keep the LCD panel and viewfinder information displayed for about 4 sec. (0).
d Program AE Like <1> (Full Auto) mode, this is a general-purpose shooting mode. The camera automatically sets the shutter speed and aperture value to suit the subject’s brightness. This is called Program AE. * stands for Program * AE stands for Auto Exposure 1 AF point Set the Mode Dial to . the subject. 2 Focus ¡ Look through the viewfinder and aim any AF point over the subject. Then press the shutter button halfway. Shutter speed Aperture the display.
d Program AE ¡ If “30"” and the maximum aperture blink, it indicates underexposure. Increase the ISO speed or use flash. ¡ If “8000” and the minimum aperture blink, it indicates overexposure. Decrease the ISO speed or use an ND filter (optional) to reduce the amount of light entering the lens. Differences Between and <1> (Full Auto) ¡ In both modes, you can freely change the automatically-set shutter speed and aperture combination (program).
s Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture value to suit the brightness of the subject. This is called Shutter-Priority AE. A fast shutter speed can freeze the motion of a fast-moving subject and a slow shutter speed can blur the subject to give the impression of motion. * stands for Time value. Fast shutter speed 1 Slow shutter speed Set the Mode Dial to . the desired shutter speed.
s Shutter-Priority AE ¡ If the maximum aperture blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture value stops blinking. ¡ If the minimum aperture blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture value stops blinking or lower the ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed. For example, “125” indicates 1/125 sec.
f Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to suit the subject brightness. This is called aperture-priority AE. The smaller the aperture (larger f/number), the wider the depth of field (range of acceptable focus). The larger the aperture (smaller f/number), the narrower the depth of field. * stands for Aperture value. With a large aperture 1 With a small aperture Set the Mode Dial to . the desired aperture value.
f Aperture-Priority AE ¡ If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (smaller f/number) until the blinking stops or set a higher ISO speed. ¡ If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (larger f/number) until the blinking stops or set a lower ISO speed. Aperture Value Display The larger the f/number, the smaller the aperture opening will be.
a Manual Exposure In this mode, you set both the shutter speed and aperture value as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a handheld exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . the desired shutter speed. 2 Set ¡ While looking at the LCD panel, turn the <6> dial. the desired aperture value. 3 Set ¡ Set the <4> switch to , and while looking at the LCD panel, turn the <5> dial.
a Manual Exposure the exposure. 5 Set ¡ Check the exposure level and set the desired shutter speed and aperture value. : Standard exposure level. : To set it to the standard exposure level, set a slower shutter speed or a larger aperture. : To set it to the standard exposure level, set a faster shutter speed or a smaller aperture. 6 Take the picture. If the exposure level mark blinks at the or level, it indicates that the exposure level exceeds the standard exposure by ±2 stops.
8 Automatic Depth-of-Field AE This mode is for obtaining a wide depth of field automatically between a near subject and far subject. It is effective for group photos and landscapes. The camera uses the nine AF points to detect the nearest and farthest subjects to be in focus. * <8> stands for Auto-depth of field. 1 Set the Mode Dial to <8>. the subject. 2 Focus ¡ Move the AF point over the subject and press the shutter button halfway.
Setting Exposure CompensationN Exposure compensation is used to alter the standard exposure setting set by the camera. You can make the image look lighter (increased exposure) or darker (decreased exposure). You can set the exposure compensation up to ±2 stops in 1/3-stop increments. the Mode Dial to any 1 Turn Creative Zone mode except . the exposure level indicator. 2 Check ¡ Press the shutter button halfway and check the exposure level indicator. the exposure compensation amount.
3 Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±2 stops in 1/3-stop increments for three successive shots. This is called Auto Exposure Bracketing (AEB). Standard exposure Decreased exposure 1 Increased exposure Select [AEB]. ¡ Turn the <5> dial to select [z AEB], then press <0>. the AEB amount. 2 Set ¡ Turn the <5> dial to set the AEB amount, then press <0>. s The icon and AEB amount will appear on the LCD panel.
3 Auto Exposure Bracketing (AEB)N Canceling AEB ¡ Follow steps 1 and 2 to set the AEB amount to < >. ¡ AEB will also be canceled automatically if you turn the <4> switch to <2>, change lenses, have flash-ready, replace the battery, or replace the CF card. Neither flash nor bulb exposures can be used with AEB. ¡ If the drive mode is set to continuous (i), the three bracketed shots will be taken continuously and then the shooting will stop automatically.
AAE LockN AE lock enables you to lock the exposure at a different place from the point of focus. After locking the exposure, you can recompose the shot while maintaining the desired exposure setting. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. ¡ Press the shutter button halfway. s The exposure setting will be displayed. the button. (0) 2 sPress lights in the viewfinder to indicate that the exposure setting is locked (AE lock).
Bulb Exposures When bulb is set, the shutter stays open while you hold down the shutter button fully, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the Mode Dial to . the shutter speed to “buLb.” 2 Set ¡ Look at the LCD panel and turn the <6> dial to select “buLb.” ¡ The next setting after “30"” is “buLb.” the desired aperture value.
Mirror LockupN Mirror lockup is enabled with C.Fn-12 [Mirror lockup] set to [1: Enable] (p.144). The mirror can be swung up separately from when the exposure is made. This prevents mirror vibrations which may blur the image during close-ups or when a super telephoto lens is used. Set Custom Functions with [c Custom Functions (C.Fn)]. 1 Press the shutter button completely. s The mirror will swing up. press the shutter button 2 Again completely. s The picture is taken and the mirror goes back down.
ULCD Panel Illumination The LCD panel is provided with illumination. Each time you press the button, the LCD panel illumination will turn on (9) or off. Use it to read the LCD panel in the dark. The illumination will turn off automatically after the shot is taken. Pressing any shooting-related button or turning the Mode Dial while the LCD panel is illuminated prolongs the illumination.
3 You can also silence the beeper You can silence the beeper so it does not sound in any shooting mode. 1 Select [Beep]. ¡ Turn the <5> dial to select [z Beep], then press <0>. [Off]. 2 Select ¡ Turn the <5> dial to select [Off], then press <0>. 3 CF Card Reminder This prevents shooting if there is no CF card in the camera. This can be set in all shooting modes. 1 Select [Shoot w/o card]. ¡ Turn the <5> dial to select [z Shoot w/o card], then press <0>. [Off].
6 Flash Photography The built-in flash or an EOSdedicated, EX-series Speedlite enables E-TTL II autoflash (evaluative flash metering with preflash), making flash photography as easy as normal shooting. The result is naturallooking flash photos. In the Basic Zone modes (except <3> <5> <7>), flash photography is fully automatic. In Creative Zone modes, flash can be used whenever necessary. First set the <4> switch to .
Using the Built-in Flash E-TTL II autoflash obtains high-precision and consistent flash shots. Using the Built-in Flash in the Basic Zone If necessary, the built-in flash will pop-up automatically in low-light or backlit conditions (except in <3> <5> <7> modes). Using the Built-in Flash in the Creative Zone Regardless of the light level, you can press the button to pop-up and fire the built-in flash whenever desired. d : For fully automatic flash photography. The shutter speed (1/ 60 sec. - 1/250 sec.
Using the Built-in Flash Built-in Flash Range With EF-S17-85mm f/4-5.6 IS USM ISO speed Wide angle: 17mm [m / ft] Telephoto: 85mm 100 Approx. 1 - 3.3 / 3.3 - 10.8 Approx. 1 - 2.3 / 3.3 - 7.5 200 Approx. 1 - 4.6 / 3.3 - 15.1 Approx. 1 - 3.3 / 3.3 - 10.8 400 Approx. 1 - 6.5 / 3.3 - 21.3 Approx. 1 - 4.6 / 3.3 - 15.1 800 Approx. 1 - 9.2 / 3.3 - 30.2 Approx. 1 - 6.5 / 3.3 - 21.3 1600 Approx. 1 - 13.0 / 3.3 - 42.7 Approx. 1 - 9.2 / 3.3 - 30.2 H: 3200 Approx. 1 - 18.4 / 3.3 - 60.4 Approx.
Using the Built-in Flash Using Red-eye Reduction When flash is used in a low-light environment, the subject’s eyes may look red in the image. “Red eye” happens when the light from the flash reflects off the retina of the eyes. The camera’s red-eye reduction feature turns on the red-eye reduction lamp to shine a gentle light into the subject’s eyes to narrow the pupil diameter or iris. A smaller pupil reduces the chances of red eye from occurring.
Using the Built-in Flash AFE lockN FE (flash exposure) lock obtains and locks the correct flash exposure reading for any part of a subject. 1 Check that the icon is lit. ¡ Press the button to pop-up the built-in flash. ¡ In the viewfinder, check that the icon is lit. the subject. 2 Focus ¡ Press the shutter button halfway. Keep pressing the shutter button halfway until step 4. Partial metering the button.
Using the Built-in Flash yFlash exposure compensationN In the same way as normal exposure compensation, you can set exposure compensation for flash. You can set flash exposure compensation up to ±2 stops in 1/3-stop increments. 1 Press the button. (9) the exposure compensation 2 Set amount. ¡ Set the <4> switch to , and while looking at the LCD panel or viewfinder, turn the <5> dial.
Using EOS-Dedicated, External Speedlites With EX-series Speedlites An EOS-dedicated, EX-series Speedlite makes flash photography as easy as normal shooting. You can easily do the flash operations below. For detailed procedures, see the Speedlite’s instruction manual. ¡E-TTL II Autoflash E-TTL II is a new autoflash exposure system incorporating improved flash exposure control and lens focusing distance information, making it more precise than the previous E-TTL (evaluative flash metering with preflash) system.
Using EOS-Dedicated, External Speedlites ¡ When using an external Speedlite, retract the built-in flash before mounting the external Speedlite. ¡ If the EX-series Speedlite’s firing mode is set to TTL autoflash with the Custom Function, the Speedlite will not fire. ¡ If autofocus cannot be achieved, the external, EOS-dedicated Speedlite’s AF-assist beam (if the Speedlite has an AF-assist beam) will be emitted automatically (except in <3> <5> <7> modes).
7 Image Playback This chapter explains image playback operations such as how to view and erase captured images and how to connect the camera to a TV monitor. For images taken with another camera: The camera might not be able to properly display images captured with a different camera or edited with a personal computer or whose file name was changed.
3 Setting the Image Review Time You can set how long the image is to be displayed on the LCD monitor right after it is captured. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. 1 Select [Review time]. ¡ Turn the <5> dial to select [x Review time], then press <0>. the desired review time. 2 Set ¡ Turn the <5> dial to select the desired setting, then press <0>.
3 Auto Image Rotation Vertical shots can be rotated automatically so that they are displayed upright during playback. 1 Select [Auto rotate]. ¡ Turn the <5> dial to select [c Auto rotate], then press <0>. [On]. 2 Select ¡ Turn the <5> dial to select [On], then press <0>. a vertical shot. 3 Take ¡ For the image review right after image capture, the image will not be displayed vertically on the LCD monitor. the image. 4 Playback ¡ Press the button.
3 Setting the LCD Brightness You can adjust the brightness of the LCD monitor to one of five levels. 1 Select [LCD Brightness]. ¡ Turn the <5> dial to select [c LCD Brightness], then press <0>. s The brightness adjustment screen will appear. the brightness. 2 Adjust ¡ While looking at the gray chart on the left, turn the <5> dial to adjust. ¡ Press <0> to exit the setting and return to the menu. To check the image’s exposure, look at the histogram (p.104).
Image Playback You can select any captured image to view. You can view a single image, the shooting information, an index display, or a magnified view. xSingle image display 1 Playback the image. ¡ Press the button. s The last captured image will appear on the LCD monitor. the image. 2 Select ¡ To playback images starting with the last image, turn the dial counterclockwise. To playback images starting with the first captured image, turn the <5> dial clockwise.
Image Playback Shooting Information Display Image Flash exposure compensation amount Shooting time Shooting date Shutter speed Images recorded/ Total images recorded Aperture Image protect Exposure compensation amount Image-recording quality Histogram File No. Histogram ISO speed Color space Metering mode Shooting mode WB correction White balance Color temperature Monochrome Original image verification data appended Sample Histograms A histogram is a graph indicating the image’s brightness.
Image Playback H Index Display Nine thumbnail images are displayed on one screen. 1 Set the camera for playback. ¡ Press the button. s The last captured image will appear on the LCD monitor. the index images. 2 Display ¡ Press the button. s The selected thumbnail will be highlighted with a green frame. the image. 3 Select ¡ Turn the <5> dial to move the green frame. Switching from the index display to another display mode ¡ To display a single image, press the button.
Image Playback u/yMagnified View You can magnify the image by 1.5x to 10x on the LCD monitor. 1 Display the image. ¡ Display the image in the single-image or image info display mode. the image. 2 Magnify ¡ Press the button. Magnified area s First, the center of the image will be magnified. ¡ To increase the magnification, hold down the button. ¡ Press the button to reduce the magnification. Hold down the button to continue reducing the magnification until it reaches the size in step 1.
Image Playback CJump Display During the single image, image with shooting information, index, or magnified image display, you can jump forward or back to images stored on the CF card. 1 Display the image. ¡ Display a single image, image with shooting information, index, or magnified image. to the jump display. 2 Go ¡ Press the button. s The jump bar will appear at the bottom of the screen. Jump bar forward or back. 3 Jump ¡ Turn the <5> dial. During magnified view, turn the <6> dial.
Image Playback 3Automated Playback of Images (Auto playback) You can playback the CF card’s images in an automatic slide show. Each image will be displayed for about 3 sec. 1 Select [Auto Play]. ¡ Turn the <5> dial to select [x Auto Play], then press <0>. s The auto play screen will appear. the auto play. 2 Start s After [Loading image...] is displayed for a few seconds, auto play will start. ¡ To pause the auto play, press <0>. ¡ During pause, [ ] will be displayed on the upper left of the image.
Image Playback 3Rotating an Image You can rotate an image by 90° or 270° clockwise. Images will then be displayed in the correct orientation during playback. 1 Select [Rotate]. ¡ Turn the <5> dial to select [x Rotate], then press <0>. s The Rotate screen will appear. the image. 2 Rotate ¡ Turn the <5> dial to select the d image to be rotated, then press <0>. s Each time you press <0>, the image will rotate clockwise. ¡ To rotate another image, repeat step 2.
Viewing the Images on a TV By connecting the camera to a TV set with the video cable (provided), you can view the captured images on a TV set. Always turn off the camera and the television before connecting or disconnecting them. 1 Connect the camera to the TV. ¡ Open the camera’s terminal cover. ¡ Use the video cable (provided) to connect the camera’s terminal to the TV monitor’s VIDEO IN terminal. ¡ Insert the cable plug all the way in. on the TV and switch the 2 Turn TV’s line input to Video IN.
3 Protecting Images This prevents the image from being erased accidentally. 1 Select [Protect]. ¡ Turn the <5> dial to select [x Protect], then press <0>. s The protect setting screen will appear. the image. 2 Protect ¡ Turn the <5> dial to select the Image protect icon image to be protected, then press <0>. s When an image is protected, the icon will appear below the image. ¡ To cancel the image protection, press <0> again. The icon will disappear. ¡ To protect another image, repeat step 2.
LErasing Images You can erase images individually or erase all the images at one time in the CF card. Only protected images will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a Single Image 1 Display the image. ¡ Press the button. the image to be erased. 2 Select ¡ Turn the <5> dial to select the image to be erased. 3 ¡ Press the button.
LErasing Images Erasing All Images the image. 1 Display ¡ Press the button. the erase menu. 2 Display ¡ Press the button. s The Erase menu will appear at the bottom of the screen. [All]. 3 Select ¡ Turn the <5> dial to select [All], then press <0>. s The confirmation dialog will appear. the images. 4 Erase ¡ Turn the <5> dial to select [OK], then press <0>. s All unprotected images will be erased. ¡ While the images are being erased, you can cancel the erasure by pressing <0>.
3 Formatting the CF Card Format the CF card before using it in the camera. Formatting a CF card will erase everything in the card. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer images to a personal computer before formatting the card. 1 Select [Format]. ¡ Turn the <5> dial to select [c Format], then press <0>. s The confirmation dialog will appear. the CF card. 2 Format ¡ Turn the <5> dial to select [OK], then press <0>.
8 Direct Printing from the Camera You can connect the camera directly to a printer and print out the images in the CF card. This chapter explains how to print your digital camera photos with a printer capable of direct printing via “ PictBridge” or Canon’s own “ CP Direct” or “ Bubble Jet Direct” standard.
Preparing to Print You do the direct printing procedure entirely through your camera’s LCD monitor. Setting the Camera On the menu, set [c Communication] to [PTP]. 1 Select [Communication]. ¡ Turn the <5> dial to select [c Communication], then press <0>. [PTP]. 2 Select ¡ Turn the <5> dial to select [PTP], then press <0>. When connecting the camera to the personal computer, set [Communication] to [Normal]. Transmissions between the camera and personal computer will not work with the [PTP] setting.
Preparing to Print the camera to the 3 Connect printer. ¡ Refer to the table (Printers and Cables) below to select the proper cable to connect the camera to printer. Printers and Cables Printer Compatibility w w A w S A S Suitable Cable PictBridge only PictBridge and CP Direct Cable provided with camera Both plugs have the icon. PictBridge and Bubble Jet Direct CP Direct only Bubble Jet Direct only Cable provided with printer Only one plug has the icon.
Preparing to Print wPictBridge ACP Direct SBubble Jet Direct the image. 6 Playback ¡ Press the button. s The image will appear and one of three icons will appear on the upper left to indicate that the camera is connected to the printer. ¡ The procedure will be different depending on the icon displayed. See the applicable pages below.
wPrinting with PictBridge The setting options will differ depending on the printer. Some settings might be disabled. For details, refer to your printer’s instruction manual. Printer connected icon 1 Select the image to be printed. ¡ Check that the icon is displayed on the upper left of the LCD monitor. ¡ Turn the <5> dial to select the image to be printed. <0>. 2 Press s The print setting screen will appear. Print setting screen Set the date imprinting to on or off. Set the printing effects.
wPrinting with PictBridge TSetting the Paper Size ¡ Turn the <5> dial to select the size of the paper loaded in the printer, then press <0>. s The Paper Type screen will appear. YSetting the Paper Type ¡ Turn the <5> dial to select the type of paper loaded in the printer, then press <0>. s The Layout screen will appear.
wPrinting with PictBridge About Layout Bordered The print will have a white border along the edges. The print will have no white borders. Borderless If your printer cannot print borderless prints, the print will have borders. **-up Option to print 8, 2, 4, 9, 16, or 20 copies of same image on one sheet. Default With a Canon printer, the print will be borderless. the other options. 4 Set ¡ If desired, also set the date imprinting, printing effects, and number of copies.
wPrinting with PictBridge printing. 5 Start ¡ Turn the <5> dial to select [Print], then press <0>. s The printing will start. ¡ When the printing ends, the screen will return to step 1. ¡ To stop the printing, press <0> while [Stop] is displayed, then turn the <5> dial to select [OK] and press <0>. ¡ Depending on the image’s file size and recording quality, it may take some time for the printing to start after you select [Print].
APrinting with CP Direct Printer connected icon 1 Select the image to be printed. ¡ Check that the icon is displayed on the upper left of the LCD monitor. ¡ Turn the <5> dial to select the image to be printed. <0>. 2 Press s The print setting screen will appear. Print setting screen Trimming frame: Appears when you want to trim the image. Sets the quantity to be printed. Sets the trimming area. Sets the printing style. Returns to step 1. Starts the printing.
APrinting with CP Direct the options as desired. 4 Set ¡ Set the [Image], [Borders], and [Date] as desired. [Image] [Borders] [Date] ¡ Turn the <5> dial to select the menu item, then press <0>. ¡ Turn the <5> dial to select the desired setting, then press <0>. ¡ [Image] is selectable when card-size paper is used. If you select [Multiple], 8 small images of the same picture will be printed on the paper. ¡ Check the [Borders] and [Date] settings and set them if necessary.
APrinting with CP Direct the trimming. 6 Set ¡ Set as necessary. ¡ For details on trimming, see page 129. printing. 7 Start ¡ Turn the <5> dial to select [Print], then press <0>. s The printing will start. ¡ When the printing ends, the screen will return to step 1. ¡ To stop the printing, press <0> while [Stop] is displayed, then turn the <5> dial to select [OK] and press <0>. ¡ The date may look light if it is imprinted on a bright background or border.
SPrinting with Bubble Jet Direct Printer connected icon 1 Select the image to be printed. ¡ Check that the icon is displayed on the upper left of the LCD monitor. ¡ Turn the <5> dial to select the image to be printed. <0>. 2 Press s The print setting screen will appear. Print setting screen Trimming frame: Appears when you want to trim the image. Sets the quantity to be printed. Sets the trimming area. Sets the printing style. Returns to step 1. Starts the printing.
SPrinting with Bubble Jet Direct [Paper] 4 Set the options as desired. [Borders] [Date] ¡ Turn the <5> dial to select the menu item, then press <0>. ¡ Turn the <5> dial to select the desired setting, then press <0>. ¡ [Paper] is the size of the paper loaded in the printer. ¡ Check the [Borders] and [Date] settings and set them if necessary. ¡ When you are done, press the button to return to the print setting screen. the number of copies. 5 Set ¡ Set as necessary.
SPrinting with Bubble Jet Direct printing. 7 Start ¡ Turn the <5> dial to select [Print], then press <0>. s The printing will start. ¡ When the printing ends, the screen will return to step 1. ¡ To stop the printing, press <0> while [Stop] is displayed, then turn the <5> dial to select [OK] and press <0>. If [Bordered] is set, the date might be imprinted on the border, depending on the printer. ¡ If [Date] is [On], the date recorded for the image will appear on the print.
Setting the Trimming You can trim the image and print only the trimmed portion as if the image was recomposed. Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again. 1 Select [Trimming]. ¡ Turn the <5> dial to select [Trimming], then press <0>. s The trimming screen will appear. the image. 2 Trim ¡ The image area within the trimming frame will be printed. ¡ The operation guide disappears while you trim the image.
Setting the Trimming Image area to be printed the menu. 3 Exit ¡ Press <0>. s The Print setting screen will reappear. s On the upper left, you can see the trimmed image area that will be printed. ¡ Depending on the printer, the trimmed image area might not be printed as you specified. ¡ The smaller you make the trimming frame, the grainier the picture will look. If the picture will be too grainy, the trimming frame will turn red. ¡ While trimming the image, look at the camera’s LCD monitor.
9 DPOF: Digital Print Order Format With DPOF (Digital Print Order Format), you can use the camera to specify which images in the CF card are to be printed and the quantity. This feature is very convenient when you make prints with a DPOFcompatible printer or photo lab. About DPOF DPOF (Digital Print Order Format) is a standard for recording print ordering instructions to the CF card. It is for images taken with a digital camera, and you can specify which photos and the quantity to print.
3 Print Ordering Print settings Set the print type, date imprinting, and file No. imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) K Print Type Date File No. Standard Prints one image on one sheet. L Index Multiple, thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date on the print. [On] imprints the file No. on the print.
3 Print Ordering [Print Type] [Date] [File No.] the menu. 4 ¡ExitPress the button. s The Print Order screen will reappear. ¡ Next, select [Order] or [All] to select the images to be printed. ¡ RAW images cannot be selected for printing. ¡ Even if [Date] and [File No.] are set to [On], the date or file No. might not be imprinted depending on the print type setting and printer type. ¡ With [Index] prints, both the [Date] and [File No.] cannot be set to [On] at the same time.
3 Print Ordering Selecting Individual Images for Printing 1 Select [Order]. ¡ Turn the <5> dial to select [Order], then press <0>. s The order screen will appear. the image to be printed. 2 Select ¡ Turn the <5> dial to select the image to be printed. ¡ Press the button to see a three-image view. To return to the single-image view, press the button. Three-image view the print. 3 Order ¡ The print order will vary depending on the [Print Type] (p.132) setting.
3 Print Ordering For [Index] ¡ If you want to include the image in the index print, checkmark the box. Otherwise, leave the box unchecked. ¡ Press <0> to checkmark the box , or press <0> again to remove the checkmark. ¡ If there are other images you want to select, repeat steps 2 and 3. ¡ You can select up to 998 images. the menu. 4 ¡ExitPress the button. s The Print Order screen will reappear. ¡ Press the button again to save the print order to the CF card. The menu will then reappear.
3 Print Ordering Selecting All images The print order can also be set or canceled for all the images in the CF card. For standard-type prints, a quantity of one will be ordered for all the images. Note that after following the “Selecting Individual Images” procedure, if you do the “Selecting All Images” procedure, the print order will change to “All images.” 1 Select [All]. ¡ Turn the <5> dial to select [All], then press <0>. s The All screen will appear. [Mark all].
3 Direct Printing with DPOF With a printer compatible with direct printing, you can easily print images specified with DPOF. 1 Prepare to print. ¡ See “Setting the Camera” (steps 1 and 2) and “Connect the camera to the printer” (steps 1 to 5) on pages 116 to 117. [Print Order]. 2 Select ¡ Turn the <5> dial to select [x Print Order], then press <0>. s The Print Order screen will appear. [Print]. 3 Select ¡ Turn the <5> dial to select [Print], then press <0>.
3 Direct Printing with DPOF ACP Direct / SBubble Jet Direct ¡ Set the [Style]. (p.123/126) printing. 5 Start ¡ Turn the <5> dial to select [OK], then press <0>. s The printing will start. ¡ To stop the printing, press <0> while [Stop] is displayed, then turn the <5> dial to select [OK] and press <0>. ¡ When printing with a PictBridge or Bubble Jet Direct printer, be sure to set the paper size. ¡ With PictBridge, the file No. cannot be imprinted.
10 Customizing the Camera Custom Functions enable you to customize various camera features to suit your picture-taking preferences. ¡ Custom Functions work in Creative Zone modes.
3 Setting a Custom FunctionN 1 Custom Function No. Select [Custom Functions (C.Fn)]. ¡ Turn the <5> dial to select [c Custom Functions (C.Fn)], then press <0>. s The Custom Function screen will appear. Custom Function No. 2 Select ¡ Turn the <5> dial to select the desired setting, then press <0>. the setting. 3 Change ¡ Turn the <5> dial to select the Description desired setting, then press <0>. ¡ Repeat steps 2 and 3 if you want to set other Custom Functions.
3 Custom Function SettingsN C.Fn-01 SET function when shooting You can change the function assigned to <0>. With C.Fn-01-1/2, you can press <0>, then look at the LCD panel and set <5> directly. 0: Default (no function) 1: Change quality Enables you to select the recording quality directly. 2: Change parameters Enables you to select the processing parameter directly. “PA-P1, P2” stand for Parameter 1 and 2, and “PA-1” to “PA-3” stand for Set 1 to 3. “PA-B/W” is for monochrome.
3 Custom Function SettingsN C.Fn-04 Shutter button/AE lock button 0: AF/AE lock 1: AE lock/AF Convenient when you want to focus and meter separately. Press the button to autofocus and press the shutter button halfway to attain AE lock. 2: AF/AF lock, no AE lock In the AI Servo AF mode, you can press the button to stop the AF operation momentarily. This prevents the AF from being thrown off by any obstacle passing between the camera and subject.
3 Custom Function SettingsN C.Fn-07 Flash firing You can enable the built-in flash, external Speedlite, and non-Canon flash connected to the PC terminal to fire. 0: Fires 1: Does not fire The flash will not fire. C.Fn-08 ISO expansion 0: Off 1: On For the ISO speed, “H” (equivalent to ISO 3200) will be selectable. C.
3 Custom Function SettingsN C.Fn-10 Superimposed display 0: On 1: Off The AF point in the viewfinder will not flash in red. Recommended when it is bothersome to see it light up. The AF point will still light when you select it. C.Fn-11 Menu button display position When you press the button, you can set the menu screen setting. 0: Previous (top if power off) Displays the preceding menu screen that was used.
3 Custom Function SettingsN C.Fn-14 E-TTL II 0: Evaluative Fully automatic flash photography for all conditions, from low light to daylight fill-flash. 1: Average The flash is averaged for the entire area covered by the flash. Since automatic flash exposure compensation will not be executed, you may have to set it yourself depending on the scene. This also applies if you use FE lock. C.
3 Custom Function SettingsN C.Fn-17 Lens AF stop button function 0: AF stop 1: AF start AF operates only while the AF stop button is pressed. While the button is pressed, AF operation with the camera is disabled. 2: AE lock while metering When the button is pressed while metering is still active, AE lock is applied. Convenient when you want to focus and meter separately. 3: AF point: M -> Auto / Auto -> ctr.
11 Reference This section will help you understand your camera better. It covers information on camera features, system accessories, and other reference information.
Function Availability Table o: Set automatically k: User selectable Mode Dial Basic Zone Creative Zone 2 3 4 5 6 7 d s f k k k k k k k k k k k k RAW k k k k k RAW + JPEG k k k k k k k k k k k k k k k k k k k k k k k k k k k k k o k k k k – o k k k k – k k k k o k k k k k k k k k Partial k k k k k Centerweighted average k k k k k Program shift k Exposure compensation k k k AEB k k k AE lock k k k D
Function Availability Table AF Modes and Drive Modes Drive modes One-Shot AF AI Servo AF AI Focus AF uSingle shooting An image cannot be taken unless focus is achieved. When focus is achieved, it is locked. With evaluative metering, the exposure setting is also locked. (The exposure setting is stored in memory before the shot is taken.) The focus tracks the subject movement. The exposure is set at the moment the picture is taken.
Troubleshooting Guide If there is a problem, first refer to this Troubleshooting Guide. Power Source The battery cannot be recharged. ¡ You are using the wrong battery. s Do not recharge any battery pack other than Battery Pack BP511A, BP-514, BP-511, or BP-512. ¡ The battery is not properly attached to the battery charger. s Attach the battery properly to the charger. (p.18) The camera does not operate even when the <4> switch is set to <1> or . ¡ s ¡ s ¡ s ¡ s The battery is exhausted.
Troubleshooting Guide The camera turns off by itself. ¡ Auto power off is in effect. s Press the shutter button halfway. If you do not want auto power off to take effect, set [c Auto power off] on the menu to [Off]. Only the icon blinks on the top LCD panel. ¡ The battery is almost exhausted. s Recharge the battery. (p.18) Shooting No images can be shot or recorded. ¡ s ¡ s ¡ s ¡ The CF card is not properly inserted. Insert the CF card properly. (p.24) The CF card is full.
Troubleshooting Guide The image is out of focus. ¡ s ¡ s The lens focus mode switch is set to . Set the lens focus mode switch to . (p.23) Camera shake occured when you pressed the shutter button. To prevent camera shake, hold the camera still and press the shutter button gently. (p.26, 38) The CF card cannot be used. ¡ s s ¡ s [Err **] is displayed on the LCD panel. If it is [Err CF], see page 114. If it is [Err 02], see page 153. You are using a non-Canon CF card.
Error Codes If a camera error occurs, “Err xx” will be displayed on the LCD panel. Follow the instruction below to resolve the problem for respective error code. If the same error occurs often, something is probably wrong with the camera. Jot down the “xx” error code and take your camera to the nearest Canon Service Center. If an error occurs after you take a picture, the camera might have missed the shot. Press the button to see if the image appears on the LCD monitor.
Major Accessories (Optional) Battery Pack BP-511A High-capacity, lithium-ion, secondary power pack. AC Adapter Kit ACK-E2 Power source kit (AC adapter, DC coupler, power cord) for supplying power to the camera with a household power outlet. Compatible with AC 100 - 240 V. Compact Power Adapter CA-PS400 Quick charger for BP-511A. It takes about 110 minutes to recharge one pack. Two packs can be attached to it at one time. DC Coupler DR-400 (optional) can also be connected to the CA-PS400.
Major Accessories (Optional) Macro Ring Lites The EX-series Macro Lites (two models) are ideal for close-up flash photography. You can fire only one or both flash tubes and control the flash ratio to easily obtain sophisticated lighting effects with E-TTL II autoflash. Remote Switch RS-80N3 This is a remote switch to prevent camera shake for super-telephoto shots, macroshooting, and bulb exposures. The cord is 80 cm/2.6 ft.
System Map Eyepiece Extender EP-EX15 Rubber Frame Eb E-series Dioptric Adjustment Lenses ST-E2 220EX 420EX 580EX Macro Ring Lite MR-14EX Bundled Accessories Macro Twin Lite MT-24EX * The Lens Kit includes the EF-S 18-55mm lens.
System Map CF card CF Card reader PC card adapter Personal computer PC card slot USB port (2.0/1.1) Windows XP (Home Edition / Professional) Windows 2000 Professional Windows ME Windows 98 Second Edition Mac OS X 10.1-10.3 Mac OS 9.0-9.2 • EOS DIGITAL Solution Disk • Digital Photo Professional Disk • Adobe Photoshop Elements Disk Data Verification Kit DVK-E2 (Ver.2.
Specifications • Type Type: Recording media: Image size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera with built-in flash Type I or II CF card * Compatible with Microdrive and 2GB or larger CF cards 22.5 x 15.0mm Canon EF lenses (including EF-S lenses) (35mm-equivalent focal length is equal to approx.1.6 times the marked focal length.
Specifications • White Balance Type: Auto, daylight, shade, cloudy, tungsten, white fluorescent light, flash, custom, color temperature setting Auto white balance: Auto white balance with the image sensor Color temperature correction: White balance correction: ±9 stops in full-stop increments White balance bracketing: ±3 stops in full-stop increments * Blue/amber bias or magenta/green bias possible Color temperature information transmission: Provided • Viewfi nder Type: Coverage: Magnification: Eyepoint: Bui
Specifications AF-assist beam: Built-in flash fires intermittently Effective range: Approx. 4.0m/13.1ft. at center, approx. 3.5m/11.5ft. at periphery • Exposure Control Metering modes: 35-zone TTL full aperture metering • Evaluative metering (linkable to any AF point) • Partial metering (approx. 9% of viewfinder at center) • Centerweighted Average Metering Metering range: EV 1-20 (at 20°C/68°F with 50mm f/1.
Specifications • External Speedlite EOS-dedicated Speedlite: E-TTL II autoflash with EX-series Speedlite PC terminal: Provided Zooming to match lens focal length: Provided • Drive System Drive modes: Continuous: Max. burst: Single, continuous, and Self-timer (10 sec.) Max. 5 shots per sec. JPEG* (Large/Fine): Approx. 20, RAW: Approx. 6 * Varies depending on the subject, ISO speed, processing parameters, CF card, etc.
Specifications • Power Source Battery: Battery life: One Battery Pack BP-511A, BP-514, BP-511, or BP-512. * AC power can also be supplied with the DC Coupler. * With Battery Grip BG-E2, size-AA batteries can be used. [shots] Temperature At 20°C/68°F Battery check: Power saving: Date/Time battery: Shooting Conditions No Flash 50% Flash Use Approx. 1000 Approx. 700 At 0°C / 32°F Approx. 750 Approx. 550 * The above figures apply when a fully-charged Battery Pack BP-511A is used. Automatic Provided.
Specifications Power cord length: Recharging time: Approx. 1.8 m / 5.9 ft. BP-511A, BP-514: Approx. 100 min. BP-511, BP-512: Approx. 90 min. Rated input: AC 100 - 240 V Rated output: DC 8.4 V Working temperature range: 0°C - 40°C / 32°F - 104°F Working humidity: 85% or lower Dimensions (W x H x D): 91 x 67 x 32.3 mm / 3.6 x 2.6 x 1.3 in Weight: 105 g / 3.7 oz (excluding power cord) ¡ All the specifications above are based on Canon’s testing standards.
Digital Camera Model DS126061 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note:This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
Index A AC Adapter Kit ........................22, 154 Access lamp....................................25 Accessories ..................................154 Add original decision data.............146 A-DEP .............................................82 Adobe RGB.....................................56 AE ...................................................74 AE lock....................................86, 149 AEB.................................................84 AF mode ........................................
Index External Speedlite ..........................97 Eyepiece cover .........................17, 89 F FE lock......................................95, 97 FEB.................................................97 File No.............................................61 Filter effects ....................................60 Firmware.........................................31 Flash ...................................92, 97, 98 Flash exposure compensation ..96, 97 Flash off ........................................
Index Paper settings ...............................119 Partial Metering...............................71 PC terminal .....................................98 PictBridge .....................................119 Playback........................................103 Playback menu..........................29, 31 Portrait ............................................42 Possible Shots ..........................21, 47 Power Outlet ...................................22 Power Switch ............................
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. For all inquiries concerning this camera, call toll free in the U.S. 1-800-OK-CANON or write to: Customer Relations, Canon U.S.A., Inc. One Canon Plaza, Lake Success, N.Y. 11042-1198 CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada1010 CANON CANADA INC.
