EOS 5D Mark IV (WG) Camera Wi-Fi (Wireless Communication) Function (Basic) Instruction manuals (PDF files) can be downloaded from the Canon Web site (p.4). www.canon.
EOS 5D Mark IV (WG) Camera Instruction Manual
Introduction The EOS 5D Mark IV is a digital single-lens reflex camera featuring a full-frame (approx. 36.0 x 24.0 mm) CMOS sensor with approx. 30.4 effective megapixels, DIGIC 6+, normal ISO speed range of ISO 100 ISO 32000, approx. 100% viewfinder coverage, high-precision and high-speed 61-point AF (up to 41 cross-type points), maximum continuous shooting speed of approx. 7.0 shots/sec., 3.2-inch LCD monitor, Dual Pixel RAW shooting, Live View shooting, 4K movie shooting, High Frame Rate (119.9p/100.
Item Check List Before starting, check that all the following items are included with your camera. If anything is missing, contact your dealer. Camera (with body cap) Wide Strap Eyecup Eg Battery Charger Battery Pack LC-E6/LC-E6E* LP-E6N (with protective cover) Interface Cable IFC-150U II Cable protector * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instruction Manual and CD-ROMs provided are listed on the next page.
Instruction Manuals and CD-ROMs Camera and Wi-Fi (Wireless Communication) Function Basic Instruction Manual This booklet consists of the full “Camera Instruction Manual” and the “Wi-Fi (Wireless Communication) Function Basic Instruction Manual”. The detailed PDF manual for the Wi-Fi/NFC (wireless communication) function can be downloaded from Canon Web site. EOS DIGITAL Solution Disk (Software CD-ROM) Contains various software.
Compatible Cards To view the Instruction Manuals (PDF files), Adobe Acrobat Reader DC or other Adobe PDF viewer (most recent version recommended) is required. Adobe Acrobat Reader DC can be downloaded for free from the Internet. Double-click a downloaded Instruction Manual (PDF file) to open it. To learn how to use PDF viewing software, refer to software’s Help section. You can also access the download site for the Software Instruction Manual from the software installation screen (p.599).
Quick Start Guide 1 2 Insert the battery (p.44). To charge the battery, see page 42. Insert the card (p.45). The camera-front side slot is for a CF card, and the camera-back side slot is for an SD card. * Shooting is possible as long as there is a CF card or an SD card in the camera. 3 Attach the lens (p.55). 4 Set the lens’s focus mode switch to (p.55). 5 Set the power switch to <1> (p.49). 6 Align the red mount index on the lens with the red mount index on the camera to attach the lens.
Quick Start Guide 6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto) (p.35). All the necessary camera settings will be set automatically. 7 Focus on the subject (p.58). 8 Take the picture (p.58). 9 Review the picture. Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus on the subject. Press the shutter button completely to take the picture.
Conventions Used in this Manual Icons in this Manual <6> <5>
<9> <0> 0/9/4/ 7/8 : : : : : : Indicates the Main Dial. Indicates the Quick Control Dial. Indicates the AF area selection button. Indicates the Multi-controller. Indicates the Setting button. Indicates that each function remains active for approx. 4 sec., 6 sec., 8 sec., 10 sec., or 16 sec. after you let go of the button.
Chapters Introduction 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 Getting Started and Basic Camera Operations 41 Basic Shooting 93 Setting the AF and Drive Modes 99 Image Settings 165 GPS Settings 227 Advanced Operations for Photographic Effects 243 Flash Photography 285 Shooting with the LCD Monitor (Live View Shooting) 297 Shooting Movies 333 Image Playback 393 Post-Processing Images 445 Sensor Cleaning 457 Transferring Images to a Computer and Print Ordering 465 Customizing the
Contents Introduction 2 Item Check List................................................................................. 3 Instruction Manuals and CD-ROMs.................................................. 4 Compatible Cards............................................................................. 5 Quick Start Guide ............................................................................. 6 Conventions Used in this Manual..................................................... 8 Chapters..............
Contents Before You Start ..............................................................................73 Formatting the Card ..................................................................... 73 Disabling the Beeper ....................................................................76 Setting the Power-off Time/Auto Power Off.................................. 76 Setting the Image Review Time ...................................................77 Reverting the Camera to the Default Settings............
Contents When Autofocus Fails .................................................................. 158 MF: Manual Focus ..................................................................... 159 i Selecting the Drive Mode ....................................................... 160 j Using the Self-timer................................................................. 163 4 Image Settings 165 Selecting the Card for Recording and Playback........................... 166 Setting the Image-Recording Quality ..
Contents 5 GPS Settings 227 GPS Features ............................................................................... 228 GPS Precautions .......................................................................... 230 Acquiring GPS Signals..................................................................231 Setting the Positioning Interval ..................................................... 236 Setting Time from GPS on the Camera ........................................
Contents 7 Flash Photography 285 D Flash Photography ................................................................... 286 Setting the Flash Function............................................................ 289 8 Shooting with the LCD Monitor (Live View Shooting) 297 A Shooting with the LCD Monitor .............................................. 298 Shooting Function Settings .......................................................... 307 Menu Function Settings....................................
Contents 10 Image Playback 393 x Image Playback ......................................................................394 B: Shooting Information Display.............................................397 x Searching for Images Quickly.................................................403 H Display Multiple Images on One Screen (Index Display) ..... 403 I Jumping through Images (Jump Display) ............................. 404 u Magnifying Images ...............................................................
Contents 11 Post-Processing Images 445 R Processing RAW Images with the Camera........................... 446 S Resizing JPEG Images........................................................... 452 N Cropping JPEG Images .......................................................... 454 12 Sensor Cleaning 457 f Automatic Sensor Cleaning .................................................. 458 Appending Dust Delete Data ........................................................ 460 Manual Sensor Cleaning .....
Contents 15 Reference 523 System Map .................................................................................. 524 Checking the Battery Information.................................................. 526 Using a Household Power Outlet.................................................. 530 H Using Eye-Fi Cards ................................................................. 532 Function Availability Table by Shooting Mode...............................536 Menu Settings ............................
Index to Features Power LCD monitor Charging the battery Î p.42 Touch control Î p.70 Battery level Î p.50 Brightness Î p.442 Battery information check Î p.526 Household power outlet Î p.530 Auto power off Î p.76 Cards Color tone Î p.443 Electronic level Î p.82 Help Î p.91 AF AF operation Î p.100 Formatting Î p.73 AF area selection mode Î p.104 Recording function Î p.166 AF point selection Î p.107 Selecting card Î p.168 AF point registration Î p.500 Lens group Î p.
Index to Features Recording Images Shooting Recording function Î p.166 Shooting mode Î p.35 Selecting card Î p.168 HDR mode Î p.263 Multiple exposures Î p.268 Creating/Selecting a folder Î p.218 Mirror lockup Î p.276 File name Î p.220 Bulb timer Î p.261 File numbering Î p.223 Interval timer Î p.281 Depth-of-field preview Î p.250 Remote switch Î p.279 Image-recording quality Î p.169 Remote control Î p.279 Dual Pixel RAW shooting Î p.175 Quick Control Î p.
Index to Features Flash External flash Movie Shooting Movie shooting Î p.333 ISO speed (movie) Î p.379 Î p.286 AF method Î p.316 FE lock Î p.286 Movie Servo AF Î p.380 Flash function settings Î p.289 Movie Servo AF speed Î p.383 Î p.294 Movie Servo AF tracking sensitivity Î p.384 Flash exposure compensation Flash Custom Function settings Î p.286 Movie recording quality Î p.351 Live View Shooting 24.00p Î p.357 Live View shooting Î p.297 High Frame Rate movie Î p.
Index to Features Playback Customization Image review time Î p.77 Custom Functions (C.Fn) Î p.480 Single-image display Î p.394 Custom Controls Î p.495 Custom Quick Control Î p.510 Î p.515 Shooting information display Î p.397 My Menu Index display Î p.403 Custom shooting mode Î p.520 Image browsing (Jump display) Î p.404 Magnified view Î p.406 Two-image display Î p.408 Sensor cleaning Image rotate Î p.411 Append Dust Delete Data Î p.460 Protect Î p.
Safety Precautions The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Warnings: Follow the warnings below. Otherwise, death or serious injuries may result.
Safety Precautions When the camera or accessories are not in use, make sure to remove the battery and disconnect the power plug from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, and corrosion. Do not use the equipment where there is flammable gas. This is to prevent an explosion or a fire. If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the exposed internal parts. There is a possibility of an electrical shock.
Safety Precautions Cautions: Follow the cautions below. Otherwise, physical injury or property damage may result. Do not use or store the product in a high-temperature location such as inside a car under the hot sun. The product may become hot and cause burns. Doing so may also cause battery leakage or explosion, which will degrade the performance or shorten the life of the product. Do not carry the camera around when it is attached to a tripod. Doing so may cause an injury or an accident.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a clean, well-wrung wet cloth.
Handling Precautions If condensation forms on the camera, do not use the camera. This is to avoid damaging the camera. If there is condensation, remove the lens, card and battery from the camera, and wait until condensation has evaporated before using the camera. If the camera will not be used for an extended period, remove the battery and store the camera in a cool, dry, well-ventilated location.
Handling Precautions Cards To protect the card and its recorded data, note the following: Do not drop, bend, or wet the card. Do not subject it to excessive force, physical shock, or vibration. Do not affix any stickers, etc., on the card. Do not store or use the card near anything that has a strong magnetic field, such as a TV set, speakers, or magnets. Also avoid places prone to having static electricity. Do not leave the card in direct sunlight or near a heat source. Store the card in a case.
Nomenclature Drive mode selection/ AF operation selection button (p.160, 163/100) Flash exposure compensation/ISO speed setting button (p.286/177) LCD panel illumination button (p.63) <6> Main Dial (p.59) White balance selection/ Metering mode selection button (p.192/253) Multi function button (p.62, 106, 286, 495) GPS antenna Lens mount index (p.55) Flash sync contacts Hot shoe (p.286) Mode Dial lock-release button (p.59) Shutter button (p.58) Mode Dial (p.
Nomenclature LCD panel (p.33, 34) Eyecup (p.278) Viewfinder eyepiece
AF start button (p.58, 100, 300, 347) AE lock button (p.259) AF point selection button (p.106, 107) Info button (p.63, 82, 86, 91, 301, 305, 344, 394) Power switch (p.49) Menu button (p.67) Quick Control button (p.64) Terminal cover <5> Quick Control Dial (p.60) Speaker Access lamp (p.47) Ambient light sensor (p.442) Multi function lock switch (p.62) <0> Setting button (p.67) PC terminal (p.
Nomenclature Dioptric adjustment knob (p.57) Focal plane mark Live View shooting/ Movie shooting switch (p.297/333) <0> Start/Stop button (p.298, 334) Creative Photo/ Comparative playback (Two-image display) button (p.183, 263, 268/408) <9> Multi-controller (p.61) Rating button (p.414, 415) Strap mount (p.37) Index/Magnify/ Reduce button (p.403/325, 329, 406) AF area selection button (p.61) Card slot cover (p.45) Playback button (p.
Nomenclature Viewfinder Information Electronic level (p.83) Spot metering circle (p.254) Large Zone AF frame (p.111) Area AF frame (p.111) Single AF point Spot AF point (p.109) Focusing screen Digital Lens Optimizer (p.210) Grid (p.81) Dual Pixel RAW shooting (p.175) < > Battery level (p.50) Flicker detection (p.215) Shooting mode (p.35) AF status indicator (p.94, 103, 151) White balance (p.192) Drive mode (p.160) Warning symbol (p.489) AF operation (p.
Nomenclature ISO speed indicator (p.177) Focus indicator (p.94, 101) AE lock (p.259) AEB in-progress (p.257) Flash-ready (p.286) Improper FE lock warning FE lock (p.286) FEB in-progress (p.293) High-speed sync (p.293) Flash exposure compensation (p.286) Shutter speed (p.246) Bulb (buLb) (p.260) FE lock (FEL) Busy (buSY) Multi function lock warning (L) No card warning (Card) Error code (Err) Aperture (p.248) Dust Delete Data acquisition (- -) 32 AF status indicator (p.
Nomenclature LCD Panel Shutter speed Bulb (buLb) FE lock (FEL) Remaining number of exposures for time-lapse movie Busy (buSY) Multi function lock warning (L) Cleaning image sensor (CLn) No card warning (Card) Error code (Err) Aperture Dust Delete Data acquisition (- -) AF point selection ([ ] AF, SEL [ ], SEL AF) AF point registration ([ ] HP, SEL [ ], SEL HP) Card warning (Card 1/2/1,2) Card full warning (FuLL 1/2/1,2) CF card selection icon CF card indicator White balance (p.
Nomenclature Logging function (p.238) GPS acquisition status Time-lapse movie shooting (p.371) Multiple-exposure shooting (p.268) Bulb timer shooting/ Interval timer shooting (p.261/281) Warning symbol (p.489) Dual Pixel RAW shooting (p.175) Flash exposure compensation (p.286) Exposure level indicator Exposure compensation amount (p.255) AEB range (p.257) Flash exposure compensation amount (p.286) Exposure compensation (p.255) 34 AF operation (p.
Nomenclature Mode Dial You can set the shooting mode. Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). F : Bulb (p.260) a : Manual exposure (p.251) f : Aperture-priority AE (p.248) s : Shutter-priority AE (p.246) d : Program AE (p.244) A : Scene Intelligent Auto (p.94) Custom shooting mode You can register the shooting mode (, , , , or ), AF operation, menu settings, etc., to the , , and Mode Dial positions (p.520).
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6N/LP-E6 (p.42). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. Battery Charger LC-E6E Charger for Battery Pack LP-E6N/LP-E6 (p.42).
Nomenclature Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap (p.278).
Nomenclature Using the Cable Protector When connecting the camera to a computer or the Connect Station, use the provided interface cable or one from Canon (shown in the System Map on page 525). When connecting the interface cable, also use the provided cable protector. Using the cable protector prevents the cable from accidental disconnection and the terminal from getting damaged.
Nomenclature Using a Genuine Interface Cable (sold separately) If you use a genuine interface cable (sold separately, p.525), run the cable through the clamp before attaching the clamp to the cable protector. Clamp Connecting interface cable without using the cable protector may damage the digital terminal. Do not use a USB 2.0 cable equipped with a Micro-B plug. It may damage the camera’s digital terminal.
MEMO 40
1 Getting Started and Basic Camera Operations This chapter explains preparatory steps before you start shooting and the basic camera operations.
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet. LC-E6E For LC-E6E Connect the power cord to the charger and insert the plug into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery is recharged or not.
Installing and Removing the Battery Load a fully-charged Battery Pack LP-E6N (or LP-E6) into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. If the battery is not installed, the image in the viewfinder becomes blurred and you cannot perform focusing. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the electrical contacts.
Installing and Removing the Card You can use a CF card and an SD card with this camera. Images can be recorded when at least one card is installed in the camera. If cards are inserted in both slots, you can select which card to record images to or can record the same images simultaneously on both cards (p.166-168). If you use an SD card, make sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 CF card (Card 1) SD card (Card 2) Open the cover.
Installing and Removing the Card the cover. 3 Close Close the cover and slide it in the CF card indicator SD card indicator direction shown by the arrows until it snaps shut. X When you set the power switch to <1> (p.49), the number of possible shots and the loaded card(s) will be displayed on the LCD panel. The images will be recorded to the card indicated by the arrow < > icon. Card selection icon Possible shots Type II CF cards, hard disk-type cards or CFast cards cannot be used.
Installing and Removing the Card Removing the Card 1 Access lamp Open the cover. Set the power switch to <2>. Check that the access lamp is off, then open the cover. If [Recording...] is displayed on the LCD monitor, close the cover. the card. 2 Remove To remove the CF card, push the CF card eject button eject button. To remove the SD card, push it in gently and release it. Then pull it out. Pull the card straight out, then close the cover.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to, read from, or erased from the card, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 51 to set the date/time/zone. <1> : The camera turns on. <2>: The camera is turned off and does not function. Set the power switch to this position when not using the camera. Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, sensor cleaning will be performed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Battery Level Indicator When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon indicates that the battery will soon be exhausted. Display Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 9-1 0 Display Level (%) Number of Possible Shots with Viewfinder Shooting (Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the date/time/zone setting screen will appear. Follow the steps below to set the time zone first. Set the camera to the time zone in which you currently live so that, when you travel, you can simply change the setting to the correct time zone for your destination, and the camera will automatically adjust the date/time.
3 Setting the Date, Time, and Zone Turn the <5> dial to select the frame below [Zone], then press <0>. Turn the <5> dial to select the time zone, then press <0>. If your desired time zone is not listed, press the button, then proceed to the next step to set it (with the time difference from the Coordinated Universal Time, UTC). To set the time difference from UTC, turn the <5> dial and select (+/-/ hour/minute) for [Time difference]. Press <0> so is displayed.
3 Setting the Date, Time, and Zone saving time. 5 SetSettheit ifdaylight necessary. Turn the <5> dial to select [Y]. Press <0> so is displayed. Turn the <5> dial to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 4 will advance by 1 hr. If [Y] is set, the daylight saving time will be canceled and the time will go back by 1 hr. 6 ExitTurnthethesetting. <5> dial to select [OK], then press <0>.
3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK]. Press the button and select the [5] tab. Turn the <6> dial to select the [52] tab. Turn the <5> dial to select [LanguageK], then press <0>. the desired language. 3 SetTurn the <5> dial to select the language, then press <0>. X The interface language will change.
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S or EF-M lenses. Attaching a Lens 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the red mount index on the lens with the red mount index on the camera and turn the lens as shown by the arrow until it clicks in place. the lens’s focus mode switch 3 Set to . stands for autofocus.
Attaching and Detaching a Lens Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrow. Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens. Do not look at the sun directly through any lens. Doing so may cause loss of vision. When attaching or detaching a lens, set the camera’s power switch to <2>. If the front part (focusing ring) of the lens rotates during autofocusing, do not touch the rotating part.
Basic Shooting Operations Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.278). If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens Eg (sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake.
Basic Shooting Operations Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing Halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel for approx. 4 sec. (metering timer/0). Pressing Completely This releases the shutter and takes the picture.
Basic Shooting Operations A MF F Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Use it to set the shooting mode. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , , or , the respective function remains selectable for approx. 6 sec. (9). During this time, you can turn the <6> dial to change the setting.
Basic Shooting Operations 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , , or , the respective function remains selectable for approx. 6 sec. (9). During this time, you can turn the <5> dial to change the setting. When the timer ends or if you press the shutter button halfway, the camera will go back to shooting-ready state. Use this dial to select the white balance, drive mode, flash exposure compensation, AF point, etc.
Basic Shooting Operations 9 Multi-controller The <9> consists of an eight-direction key and a button at the center. Use your thumb to tilt the <9> in the desired direction. Use it to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting or movie shooting, scroll around magnified images during playback, set the Quick Control, etc. You can also use it to select and set menu items. p AF Area Selection Button For selecting the AF area (p.106).
Basic Shooting Operations B Multi Function Button Use the button for AF area selection mode (p.106), FE lock (p.286), and other functions. To select the AF area selection mode, press the button (9), then press the button.
Basic Shooting Operations U LCD Panel Illumination You can illuminate the LCD panel by pressing the button. Turn on (9) or off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying the Quick Control Screen After you press the button a number of times (p.86), the Quick Control screen (p.88) or Custom Quick Control screen (p.510) will appear.
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor with intuitive operations. This is called Quick Control. The basic operating procedures are the same for the Quick Control screen (p.88) and the Custom Quick Control screen (p.510). 1 Press the button (7). X The Quick Control screen will appear. the desired functions. 2 SetUse <9> to select a function. X The setting of the selected function is displayed.
Q Quick Control for Shooting Functions Functions Settable with the Quick Control Aperture (p.248) Shutter speed (p.246) Flash exposure compensation (p.286, 293) Exposure compensation/ AEB setting (p.255/257) ISO speed (p.177) Custom Controls (p.495) Picture Style (p.183) Image-recording quality (p.169) AF operation (p.100) White balance (p.192) Recording function/ Card selection (p.166) Metering mode (p.253) White balance correction / White balance bracketing (p.198/199) Auto Lighting Optimizer (p.
Q Quick Control for Shooting Functions Quick Control Ð <0> Select the desired function and press <0>. The function setting screen will appear. Turn the <6> or <5> dial to change some of the settings. There are also functions that are set by pressing the button. Press <0> to finalize the setting and return to the previous screen. When you select < > (p.495) and press the button, the previous screen will reappear. Custom Quick Control You can customize the layout of the Quick Control screen.
3 Menu Operations You can set various settings with the menus such as the imagerecording quality, date/time, etc. button <6> Main Dial LCD monitor <5> Quick Control Dial button <0> Setting button Mode Menu Screen * Certain menu tabs and menu items are not displayed in the mode.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Each time you press the button, the main tab (group of functions) will switch. Turn the <6> dial to select a secondary tab. For example, the [z5] tab refers to the screen displayed when the z (Shooting) tab’s fifth box “ ” from the left is selected. the desired item. 3 Select Turn the <5> dial to select the item, then press <0>. the setting.
3 Menu Operations The explanation of menu functions hereafter assumes that you have pressed the button to display the menu screen. You can also use <9> to select and set menu functions. (Except for [31: Erase images] and [51: Format card].) To cancel the operation, press the button. For details about each menu item, see page 540. Dimmed Menu Items Example: Highlight tone priority Dimmed menu items cannot be set. The menu item is dimmed if another function setting is overriding it.
d Operating the Camera with Touch Screen You can operate the camera by touching the LCD monitor (touchsensitive panel) with your fingers. Tap Sample Display (Quick Control) Use your finger to tap on (touch briefly and then remove your finger from) the LCD monitor. By tapping, you can select menus, icons, etc., displayed on the LCD monitor. When touch operation is possible, a frame will appear around the icon (except on menu screens). For example, when you tap on [Q], the Quick Control screen appears.
d Operating the Camera with Touch Screen Drag Sample Display (Menu screen) Slide your finger while touching the LCD monitor.
d Operating the Camera with Touch Screen 3 Touch Control Settings 1 Select [Touch control]. Under the [52] tab, select [Touch control], then press <0>. the touch control sensitivity 2 Set setting. Select the desired setting, then press <0>. [Standard] is the normal setting. [Sensitive] provides a more reactive touch screen response than [Standard]. Try using both settings and select the one you prefer. To disable touch operations, select [Disable].
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with this camera. When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card]. Under the [51] tab, select [Format card], then press <0>. the card.
Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full of images or data. A card-related error is displayed (p.573). Low-level Formatting Perform low-level formatting if the SD card’s reading or writing speed seems slow or if you want to totally erase the data on the card. Since low-level formatting will erase all recordable sectors on the SD card, the formatting will take longer than normal formatting.
Before You Start If you format a CF card exceeding 128 GB or SDXC card with this camera and then insert it into another camera, an error may be displayed and the card may become unusable. Certain computer operating systems or card readers may not recognize a card formatted in exFAT. When the card is formatted or data is erased, only the file management information is changed. The actual data is not completely erased. Be aware of this when selling or discarding the card.
Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved, during self-timer shooting, and during touch operations. 1 Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. [Disable]. 2 Select Select [Disable], then press <0>. X The beeper will not sound. If [Touch to ] is selected, the beeper will be silent only for touch operations.
Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor immediately after shooting. To keep the captured image displayed, set [Hold]. To not have the captured image displayed, set [Off]. 1 Select [Image review]. Under the [z1] tab, select [Image review], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>. If [Hold] is set, the image will be displayed until the auto power off time elapses.
Before You Start Shooting Function Settings One-Shot AF Single-point AF (Manual selection) Center Canceled q (Evaluative Metering mode metering) AF operation AF area selection mode AF point selection Registered AF point ISO speed settings ISO speed Range for stills Auto range Automatic setting (Auto) Minimum: 100 Maximum: 32000 Minimum: 100 Maximum: 12800 Minimum shutter Auto speed for auto Drive mode u (Single shooting) Exposure Canceled compensation/AEB Flash exposure Canceled compensation Multiple ex
Before You Start Image Recording Settings Image quality 73 Dual Pixel RAW Disable Picture Style Standard Auto Lighting Standard Optimizer Lens aberration correction Peripheral Enable illumination correction Distortion Disable correction Digital Lens Disable Optimizer Chromatic Enable aberration correction Diffraction Enable White balance Q (Ambience priority) Custom White Canceled Balance White balance shift Canceled White balance Canceled bracketing Color space sRGB Long exposure noise Disable reductio
Before You Start Live View Shooting Settings Live View shooting AF method Touch shutter Grid display Aspect ratio Exposure simulation Enable u+Tracking Disable Off 3:2 Enable Silent LV shooting Mode 1 Metering timer 8 sec.
l Displaying the Grid in the Viewfinder You can display a grid in the viewfinder to help you check the camera tilt or compose the shot. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Grid display]. [Show]. 3 Select X When you exit the menu, the grid will appear in the viewfinder. You can display a grid on the LCD monitor during Live View shooting and before you start shooting a movie (p.309, 382).
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help you correct the camera tilt. Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level. If the electronic level does not appear, set [53: z button display options] so that the electronic level can be displayed (p.86). the camera’s tilt.
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder An electronic level can be displayed on the upper part of the viewfinder. Since this indicator is displayed during shooting, you can take the picture while checking the camera tilt. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Electronic level]. 3 Select [Show]. the shutter button halfway.
3 Setting the Viewfinder Information DisplayN The shooting function settings (Battery (remaining capacity), Shooting mode, White balance, Drive mode, AF operation, Metering mode, Image quality (image type), Digital Lens Optimizer, Dual Pixel RAW (shooting), Flicker detection) can be displayed in the viewfinder. By default, only Flicker detection is checkmarked [X]. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Show/hide in viewfinder].
3 Setting the Viewfinder Information DisplayN If no card is inserted in the camera, the image-recording quality (image type: JPEG/RAW) will not be displayed. When you press the or button, operate the lens’s focus mode switch, or when a lens equipped with electronic manual focusing function is used and the AF and MF switches as the lens focusing ring is turned (p.138), the respective information will appear in the viewfinder regardless of whether it is checkmarked.
B Button Functions When you press the button with the camera being ready to shoot, you can switch the display as follows: Displays camera settings (p.87), Electronic level (p.82), Quick Control screen (p.88), and Custom Quick Control screen (p.510). [z button display options] under [53] tab enables you to select the options displayed when the button is pressed. Select the desired display option and press <0> to add a checkmark [X]. Then select [OK] to register the setting.
B Button Functions If you turn off the power with the Electronic level, Quick Control screen, or Custom Quick Control screen displayed, the same screen will be displayed when you turn on the power again. To cancel this function, press the button a number of times until the screen is blank, then turn off the power switch. Note that you cannot remove the [X] for all four display options. The [Displays camera settings] sample screen is displayed in English for all languages.
B Button Functions Quick Control Screen Aperture Shutter speed AE lock Highlight tone priority ISO speed Shooting mode Exposure level indicator Flash exposure compensation Exposure compensation Custom Controls White balance correction Card indicator Image-recording quality Picture Style Card selection icon AF operation Possible shots/ Auto cleaning Quick Control icon Battery level Max.
B Button Functions Button Operation for the Quick Control and Custom Quick Control Screens When you press the , , , or button, the setting screen will appear and you can use <6>, <5>, <9>, , or to set the function.
R Setting Multi Function Lock By setting the switch to the right, you can prevent the settings from being inadvertently changed by such as the following: Accidentally operating Main Dial, Quick Control Dial or Multi-controller, pressing the AF area selection button or tapping on the touch screen. For details on the Multi function lock switch, see page 62. 1 Select [Multi function lock]. Under the [55] tab, select [Multi function lock], then press <0>.
Help When [z Help] is displayed at the bottom of the menu screen, the feature’s description (Help) can be displayed. Press the button to display the Help. Press it again to turn off the Help display. If the Help fills more than one screen, a scroll bar will appear on the right edge. Turn the <5> dial to scroll.
MEMO 92
2 Basic Shooting This chapter explains how to use the Mode Dial’s (Scene Intelligent Auto) mode for easy picture taking. In the mode, all you do is point and shoot and the camera sets everything automatically (p.536). Also, to prevent botched pictures due to misoperations, advanced shooting function settings cannot be changed. Scene Intelligent Auto Auto Lighting Optimizer In the mode, the Auto Lighting Optimizer (p.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically on either the still or moving subject by detecting the motion of the subject (p.97). 1 Area AF frame Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. the Area AF frame over the 2 Aim subject.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. X The captured image will be displayed for approx. 2 sec. on the LCD monitor. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If you do not obtain the desired color tones, change the mode to , , , or , set a Picture Style other than , then shoot again (p.183). FAQ The focus indicator blinks and focus is not achieved.
A Fully Automatic Shooting (Scene Intelligent Auto) Pressing the shutter button halfway does not focus on the subject. If the focus mode switch of the lens is set to (manual focus), set it to (autofocus). The shutter speed display is blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (sold separately, p.286) is recommended.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, positioning the subject toward the left or right to include a balanced background will result in a picture with better perspective. In the mode, pressing the shutter button halfway to focus on a still subject will lock the focus on that subject. Recompose the shot while keeping the shutter button pressed halfway, and then press the shutter button completely to take the picture. This is called “focus lock”.
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 297. 1 Set the Live View shooting/Movie shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. X The Live View image will appear on the LCD monitor. on the subject. 3 Focus Press the shutter button halfway to focus.
3 Setting the AF and Drive Modes The AF points in the viewfinder are arranged to make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF operation and drive mode that best match the shooting conditions and subject. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . In the mode, the AF operation and AF area selection mode are set automatically. stands for autofocus.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In the mode, “AI Focus AF” is set automatically. 1 Set the lens’s focus mode switch to . the , , , , 2 orSet mode. 3 Press the button (9). the AF operation. 4 Select While looking at the LCD panel or in the viewfinder, turn the <6> dial. X: One-Shot AF 9: AI Focus AF Z: AI Servo AF When the AF area selection mode (p.
f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. Focus indicator AF point The AF point that achieves focus is displayed, and the focus indicator in the viewfinder will also light up. With evaluative metering (p.253), the exposure setting will be set at the same time as focus is achieved. While you hold down the shutter button halfway, the focus will be locked.
f: Selecting the AF OperationN AI Servo AF for Moving Subjects This AF operation is suited for moving subjects when the focusing distance keeps changing. While you hold down the shutter button halfway, the camera will keep focusing on the subject continuously. The exposure is set at the moment the picture is taken. When the AF area selection mode (p.109) is set to Automatic selection AF, focus tracking will continue as long as the Area AF frame covers the subject.
f: Selecting the AF OperationN AF Operation Indicator When you press the shutter button halfway and the camera is focusing with AF, the icon will appear on the lower right of the viewfinder. In One-Shot AF mode, the icon also appears if you press the shutter button halfway after focus is achieved. The AF operation indicator can be displayed outside the viewfinder’s field of view (p.151).
S Selecting the AF Area and AF PointN The camera has 61 AF points for autofocusing. You can select the AF area selection mode and AF point(s) suiting the scene or subject. Depending on the lens attached to the camera, the number of usable AF points, AF point patterns, Area AF frame shape, etc. vary. For details, see “Lenses and Usable AF Points” on page 115. AF Area Selection Mode You can select one of seven AF area selection modes. For the selection procedure, see page 106.
S Selecting the AF Area and AF PointN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and the surrounding AF points are used to focus. Zone AF (Manual selection of zone) One of nine focusing zones is used to focus. Large Zone AF (Manual selection of zone) One of three focusing zones (left, center, and right) is used to focus. Automatic selection AF The Area AF frame (entire AF area) is used to focus.
S Selecting the AF Area and AF PointN Selecting the AF Area Selection Mode 1 Press the button (9). Press the
button or 2 button. Look through the viewfinder and press the
(AF area selection) button or button. Each time you press the
button or button, the AF area selection mode changes. With [24: Select AF area selec. mode], you can limit the selectable AF area selection modes to only those you want to use (p.143).
S Selecting the AF Area and AF PointN Selecting the AF Point Manually You can manually select the AF point or zone. 1 Press the button (9). X The AF points will be displayed in the viewfinder. In AF point expansion modes, adjacent AF points will also be displayed. In the Zone AF or Large Zone AF mode, the selected zone will be displayed. an AF point. 2 Select The AF point selection will change in the direction you tilt <9>.
S Selecting the AF Area and AF PointN AF Point Display Indications Pressing the button lights up the AF points that are cross-type AF points for high-precision autofocusing. The blinking AF points are horizontal-line or vertical-line sensitive. For details, see pages 113-121. Registering the AF point You can register a frequently-used AF point to the camera. When you use the button set with the [83: Custom Controls] (p.
AF Area Selection ModesN Single-point Spot AF (Manual selection) For pinpoint focusing over a narrower area than with Single-point AF. Select one AF point to focus. Effective for pinpoint focusing or focusing on overlapping subjects such as an animal in a cage. Since Single-point Spot AF covers a very small area, focusing may be difficult during handheld shooting or for a moving subject. Single-point AF (Manual selection) Select one AF point to be used for focusing.
AF Area Selection ModesN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and surrounding AF points are used to focus. Focusing is performed over a wider area than with AF point expansion (manual selection ). Effective when it is difficult to track a moving subject with just one AF point. AI Servo AF and One-Shot AF work in the same way as with AF point expansion (manual selection ) mode (p.109).
AF Area Selection ModesN Large Zone AF (Manual selection of zone) The AF area is divided into three focusing zones (left, center, and right) for focusing. Since the focusing area is larger than with Zone AF and all the AF points in the selected zone are used for the automatic AF point selection, it is superior to single-point AF and AF point expansion in tracking the subject, and it is effective for moving subjects.
AF Area Selection ModesN When AI Servo AF mode is set for Zone AF, Large Zone AF, or Automatic selection AF, the active AF point will keep switching to track the subject. However, under certain shooting conditions (such as when the subject is small), it may not be able to track the subject. With Single-point Spot AF, focusing with an EOS-dedicated, external Speedlite’s AF-assist beam may be difficult.
AF Sensor The camera’s AF sensor has 61 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. When using lenses with a maximum aperture of f/2.8 or faster, high-precision AF is possible at the viewfinder center. Depending on the lens attached to the camera, the number of usable AF points, AF point patterns, Area AF frame shape, etc. vary. For details, see “Lenses and Usable AF Points” on page 115.
AF Sensor These focusing sensors are geared to obtain higher precision focusing for lenses with a maximum aperture of f/2.8 or faster. A diagonal cross pattern makes it easier to focus subjects that may be difficult to focus. They cover the five AF points vertically aligned at the center. These focusing sensors are geared to obtain high-precision focusing for lenses with a maximum aperture of f/4 or faster. Since they have a horizontal pattern, they can detect vertical lines.
Lenses and Usable AF Points Although the camera has 61 AF points, the number of usable AF points, focusing patterns, Area AF frame shape, etc. vary depending on the lens. The lenses are thereby classified into eleven groups from A to K. When using a lens in groups G to K, fewer AF points will be usable. Lens groups are listed on pages 122-126. Check which group your lens belongs to. When you press the button, the AF points indicated by the mark will blink. (The / / AF points will stay lit.
Lenses and Usable AF Points Group B Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Dual cross-type AF point. Subject tracking is superior and the focusing precision is higher than with other AF points. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group C Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Cross-type AF point.
Lenses and Usable AF Points Group E Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group F Autofocusing with 61 points is possible. All the AF area selection modes are selectable. If an extender is attached (extender compatible lenses only) and the maximum aperture is f/8 (greater than f/5.
Lenses and Usable AF Points Group G Autofocusing with the 47 points shown in the diagram is possible. (Not possible with all 61 AF points.) All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 61-point Automatic selection AF. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. : Disabled AF points (not displayed).
Lenses and Usable AF Points Group I Autofocusing with the 13 points shown in the diagram is possible. Only the following AF area selection modes are selectable: Single-point Spot AF, Single-point AF, AF point expansion (manual selection ), Zone AF (Manual selection of zone), and 13-point automatic selection AF. If an extender is attached (extender compatible lenses only) and the maximum aperture is f/8 (greater than f/5.6 but not exceeding f/8), AF will be possible. : Cross-type AF point.
Lenses and Usable AF Points Group J Autofocusing with the 9 points shown in the diagram is possible. Only the following AF area selection modes are selectable: Single-point Spot AF, Single-point AF, AF point expansion (manual selection ), and 9point automatic selection AF. If an extender is attached (extender compatible lenses only) and the maximum aperture is f/8 (greater than f/5.6 but not exceeding f/8), AF will be possible. : Cross-type AF point.
Lenses and Usable AF Points Group K AF is possible with the center AF point and the adjacent AF points above, below, on the left, and on the right. Only the following AF area selection modes are selectable: Single-point Spot AF, Single-point AF, and AF point expansion (manual selection ). : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved.
Lenses and Usable AF Points Lens Group Designations (As of May 2016) EF14mm f/2.8L USM EF14mm f/2.8L II USM EF15mm f/2.8 Fisheye EF20mm f/2.8 USM EF24mm f/1.4L USM EF24mm f/1.4L II USM EF24mm f/2.8 EF24mm f/2.8 IS USM EF28mm f/1.8 USM EF28mm f/2.8 EF28mm f/2.8 IS USM EF35mm f/1.4L USM EF35mm f/1.4L II USM EF35mm f/2 EF35mm f/2 IS USM EF40mm f/2.8 STM EF50mm f/1.0L USM EF50mm f/1.2L USM EF50mm f/1.4 USM EF50mm f/1.8 EF50mm f/1.8 II EF50mm f/1.8 STM EF50mm f/2.5 Compact Macro EF50mm f/2.
Lenses and Usable AF Points EF300mm f/4L USM + Extender EF2x III EF300mm f/4L IS USM EF300mm f/4L IS USM + Extender EF1.4x I/II/III EF300mm f/4L IS USM + Extender EF2x I/II EF300mm f/4L IS USM + Extender EF2x III EF400mm f/2.8L USM EF400mm f/2.8L USM + Extender EF1.4x I/II/III EF400mm f/2.8L USM + Extender EF2x I/II/III EF400mm f/2.8L II USM EF400mm f/2.8L II USM + Extender EF1.4x I/II/III EF400mm f/2.8L II USM + Extender EF2x I/II/III EF400mm f/2.8L IS USM EF400mm f/2.8L IS USM + Extender EF1.
Lenses and Usable AF Points EF1200mm f/5.6L USM + Extender EF1.4x I/II/III EF8-15mm f/4L Fisheye USM EF11-24mm f/4L USM EF16-35mm f/2.8L USM EF16-35mm f/2.8L II USM EF16-35mm f/4L IS USM EF17-35mm f/2.8L USM EF17-40mm f/4L USM EF20-35mm f/2.8L EF20-35mm f/3.5-4.5 USM EF22-55mm f/4-5.6 USM EF24-70mm f/2.8L USM EF24-70mm f/2.8L II USM EF24-70mm f/4L IS USM EF24-85mm f/3.5-4.5 USM EF24-105mm f/3.5-5.6 IS STM EF24-105mm f/4L IS USM EF24-105mm f/4L IS II USM EF28-70mm f/2.8L USM EF28-70mm f/3.5-4.
Lenses and Usable AF Points EF70-200mm f/4L IS USM + Extender EF2x I/II EF70-200mm f/4L IS USM + Extender EF2x III EF70-210mm f/3.5-4.5 USM EF70-210mm f/4 EF70-300mm f/4-5.6 IS USM EF70-300mm f/4-5.6L IS USM EF70-300mm f/4.5-5.6 DO IS USM EF75-300mm f/4-5.6 EF75-300mm f/4-5.6 USM EF75-300mm f/4-5.6 II EF75-300mm f/4-5.6 II USM EF75-300mm f/4-5.6 III EF75-300mm f/4-5.6 III USM EF75-300mm f/4-5.6 IS USM EF80-200mm f/2.8L EF80-200mm f/4.5-5.6 EF80-200mm f/4.5-5.6 USM EF80-200mm f/4.5-5.6 II EF90-300mm f/4.
Lenses and Usable AF Points If Extender EF2x (I/II/III) is attached to the EF180mm f/3.5L Macro USM lens, AF is not possible. When using a lens and Extender EF1.4x III/EF2x III in a combination marked with an asterisk (*) or a lens and extender in a combination marked with two asterisks (**), precise focus may not be achieved with AF. In such a case, refer to the Instruction Manual of the lens or extender used. If you use a TS-E lens, manual focusing will be required.
3 Selecting AI Servo AF CharacteristicsN You can easily fine-tune AI Servo AF to suit a particular subject or shooting scene just by selecting an option from case 1 to case 6. This feature is called the “AF Configuration Tool”. 1 Select the [21] tab. a case. 2 Select Turn the <5> dial to select a case icon, then press <0>. X The selected case will be set. The selected case is indicated in blue.
3 Selecting AI Servo AF CharacteristicsN Case 1: Versatile multi purpose setting Default settings • Tracking sensitivity: 0 • Accel./decel. tracking: 0 • AF pt auto switching: 0 Standard setting suited for any moving subject. Works with various subjects and scenes.
3 Selecting AI Servo AF CharacteristicsN Case 3: Instantly focus on subjects suddenly entering AF points Default settings • Tracking sensitivity: Responsive: +1 • Accel./decel. tracking: +1 • AF pt auto switching: 0 Once an AF point starts tracking the subject, this setting enables the camera to consecutively focus on subjects at different distances. If a new subject appears in front of the target subject, the camera will start focusing on the new subject.
3 Selecting AI Servo AF CharacteristicsN Case 5: For erratic subjects moving quickly in any direction Default settings • Tracking sensitivity: 0 • Accel./decel. tracking: 0 • AF pt auto switching: +1 Even if the target subject moves dramatically up, down, left, or right, the AF point will switch automatically to focus-track the subject. Effective for shooting subjects that move dramatically up, down, left, or right.
3 Selecting AI Servo AF CharacteristicsN Case 6: For subjects that change speed and move erratically Default settings • Tracking sensitivity: 0 • Accel./decel. tracking: +1 • AF pt auto switching: +1 Geared for tracking moving subjects whose speed can change dramatically and suddenly. Also, if the target subject moves dramatically up, down, left or right and it is difficult to focus, the AF point switches automatically to track the subject.
3 Selecting AI Servo AF CharacteristicsN Parameters Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle cuts across the AF points or when the subject strays from the AF point. 0 Default setting. Suitable for moving subjects in general. Locked on: -2 / Locked on: -1 The camera will try to continue focusing on the subject even if an obstacle cuts across the AF points or if the subject strays from the AF points.
3 Selecting AI Servo AF CharacteristicsN Acceleration/deceleration tracking This sets the tracking sensitivity for moving subjects whose speed can momentarily change dramatically by starting or stopping suddenly, etc. 0 Suited for subjects that move at a steady speed (minor changes in moving speed). -2 / -1 Suited for subjects that move at a steady speed (minor changes in moving speed).
3 Selecting AI Servo AF CharacteristicsN AF point auto switching This sets the switching sensitivity of the AF points as they track the subject moving dramatically up, down, left, or right. This setting takes effect when the AF area selection mode is set to AF point expansion (manual selection ), AF point expansion (manual selection, surrounding points), Zone AF, Large Zone AF, or Automatic selection AF. 0 Standard setting for gradual AF point switching.
3 Selecting AI Servo AF CharacteristicsN Changing Cases’ Parameter Settings You can manually adjust each case’s three parameters: 1. Tracking sensitivity, 2. Acceleration/deceleration tracking, and 3. AF point auto switching. 1 Select a case. Turn the <5> dial to select the icon of the case you want to adjust. the button. 2 Press The selected parameter will be highlighted with a purple frame. the parameter to adjust. 3 Select Select the parameter to adjust, then press <0>. the adjustment.
3 Customizing AF FunctionsN With the [22] to [25] menu tabs, you can set the AF functions to suit your shooting style or subject. 22: AI Servo AI Servo 1st image priority AF2 You can set the AF operation characteristics and shutter-release timing for the first shot with AI Servo AF. : Equal priority Equal priority is given to focusing and shutter release. : Release priority Pressing the shutter button takes the picture immediately even if focus has not been achieved.
3 Customizing AF FunctionsN AI Servo 2nd image priority AF2 With AI Servo AF for continuous shooting, you can preset the AF operation characteristics and shutter-release timing for the subsequent shots after the first shot in continuous shooting. 0: Equal priority Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, continuous shooting speed may slow down.
3 Customizing AF FunctionsN 23: One Shot Lens electronic MF AF3 With the following USM and STM lenses equipped with an electronic manual focusing function, you can set whether to use electronic manual focusing. EF50mm f/1.0L USM EF85mm f/1.2L USM EF85mm f/1.2L II USM EF200mm f/1.8L USM EF300mm f/2.8L USM EF600mm f/4L USM EF400mm f/2.8L USM EF1200mm f/5.6L USM EF400mm f/2.8L II USM EF28-80mm f/2.8-4L USM EF500mm f/4.5L USM EF40mm f/2.8 STM EF50mm f/1.8 STM EF24-105mm f/3.5-5.
3 Customizing AF FunctionsN AF-assist beam firing AF3 Enables or disables the EOS-dedicated external Speedlite’s AF-assist beam. ON: Enable The external Speedlite emits the AFassist beam when necessary. OFF: Disable The external Speedlite will not emit the AF-assist beam. Useful when the AFassist beam may disturb others. IR: IR AF assist beam only When an external Speedlite is attached, only the infrared AF-assist beam will be emitted.
3 Customizing AF FunctionsN One-Shot AF release priority AF3 You can set the AF operation characteristics and shutter-release timing for One-Shot AF. : Focus priority The picture will not be taken until focus is achieved. Useful when you want to achieve focus before capturing the image. : Release priority Priority is given to the timing of shutter release instead of achieving focus. This gives priority to capturing the image rather than achieving precise focus.
3 Customizing AF FunctionsN 24 Lens drive when AF impossible AF4 If focus cannot be achieved with autofocus, you can have the camera keep searching for the precise focus or have it stop searching. ON: Continue focus search If focus cannot be achieved with autofocus, the lens is driven to search for the precise focus. OFF: Stop focus search If autofocus starts and the focus is far off or if focus cannot be achieved, the lens drive will not be performed.
3 Customizing AF FunctionsN Selectable AF point AF4 You can change the number of manually selectable AF points. With Zone AF, Large Zone AF, or Automatic selection AF set, AF will be performed with the selected AF area selection mode (Zone AF, Large Zone AF, or Automatic selection AF) regardless of the [Selectable AF point] setting. : All points All AF points will be manually selectable. : Only cross-type AF points Only the cross-type AF points will be manually selectable.
3 Customizing AF FunctionsN Select AF area selection mode AF4 You can limit the selectable AF area selection modes to suit your shooting preferences. Select the desired selection mode and press <0> to add a checkmark [X]. Then select [OK] to register the setting. The AF area selection modes are explained on pages 109-111. : Manual select.:Spot AF : Manual selection:1 pt AF : Expand AF area: : Expand AF area:Surround : Manual select.:Zone AF : Manual select.
3 Customizing AF FunctionsN AF area selection method AF4 You can set the method for changing the AF area selection mode. :S9 M-Fn button After you press the button, pressing the
(AF area selection) button or button changes the AF area selection mode. :S9 Main Dial After you press the button, pressing the
(AF area selection) button or turning the <6> dial changes the AF area selection mode. When [S9Main Dial] is set, use the <9> to move the AF point horizontally.
3 Customizing AF FunctionsN : Separate AF pts: Area+pt The AF area selection mode and AF point (or zone) can be set separately for each camera orientation (1. Horizontal, 2. Vertical with the camera grip at the top, 3. Vertical with the camera grip at the bottom). When you manually select the AF area selection mode and AF point (or zone) for each of the three camera orientations, they will be registered for the respective orientation.
3 Customizing AF FunctionsN Initial AF Point, AI Servo AF AF4 You can set the AI Servo AF’s starting AF point for when the AF area selection mode is set to Auto selection AF. : Initial AF pt selected AI Servo AF will start with the manually-selected AF point when the AF operation is set to AI Servo AF and the AF area selection mode is set to Auto selection AF. : Manual AF pt If you switch from Manual select.
3 Customizing AF FunctionsN Auto AF point selection: EOS iTR AF AF4 EOS iTR* AF performs autofocus by recognizing faces and subject colors. EOS iTR AF works when the AF area selection mode is set to Zone AF, Large Zone AF, or Automatic selection AF. * intelligent Tracking and Recognition: a function that identifies the subject with the metering sensor in order for the AF points to track it.
3 Customizing AF FunctionsN If [EOS iTR AF (Face priority)] or [EOS iTR AF] is set, the camera may take longer to focus than when [Disable] is set. Even if you set [EOS iTR AF (Face priority)] or [EOS iTR AF], the expected effect may not be obtained depending on the shooting conditions and subject. Under light so low that the EOS-dedicated, external Speedlite emits the AF-assist beam automatically, AF points are selected automatically based only on AF information.
3 Customizing AF FunctionsN AF point display during focus AF5 You can set whether to display the AF point(s) when AF starts, during AF, when focus is achieved, and when the metering timer is active after focus is achieved.
3 Customizing AF FunctionsN VF display illumination AF5 You can set whether the AF points in the viewfinder are to light up in red when focus is achieved. AUTO: Auto The AF points achieving focus in low light or with a dark subject will automatically light up in red. ON: Enable The AF points light up in red regardless of the ambient light level. OFF: Disable The AF points do not light up in red.
3 Customizing AF FunctionsN AF status in viewfinder AF5 You can display the AF status icon indicating AF operation either inside or outside of the viewfinder's field of view. : Show in field of view The AF status icon is displayed in the lower right of the viewfinder’s field of view. : Show outside view The icon is displayed below the focus indicator outside the viewfinder’s field of view. See page 103 for the AF operation display.
3 Fine Adjustment of AF’s Point of FocusN Fine adjustment of the AF’s point of focus is possible for viewfinder shooting. This is called “AF Microadjustment”. Before making the adjustment, read “General Cautions for AF Microadjustment” and “Notes for AF Microadjustment” on page 157. Normally, this adjustment is not required. Perform this adjustment only if necessary. Note that performing this adjustment may prevent accurate focusing from being achieved.
3 Fine Adjustment of AF’s Point of FocusN the adjustment. 4 Make Set the adjustment amount. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to behind the standard point of focus. After making the adjustment, press <0>. Select [All by same amount], then press <0>. the result of the 5 Check adjustment. Take a picture and play back the image (p.
3 Fine Adjustment of AF’s Point of FocusN Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment is registered, the point of focus will always be shifted by the adjustment amount. Set the adjustment amount manually by repeatedly making adjustments, shooting, and checking the results until the desired result is achieved.
3 Fine Adjustment of AF’s Point of FocusN Entering the Serial Number Select the digit to be entered, then press <0> so is displayed. Enter the number, then press <0>. After entering all the digits, select [OK]. Lens Serial Number In step 3, if “ * ” appears in front of the 10-digit lens serial number, you can register only one unit of the same lens model. Even if you enter the serial number, “ * ” will remain displayed.
3 Fine Adjustment of AF’s Point of FocusN Single focal length lens Zoom lens the adjustment. 4 Make For a zoom lens, select the wideangle (W) or telephoto (T) end. Pressing <0> will turn off the purple frame and make the adjustment possible. Set the adjustment amount, then press <0>. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to behind the standard point of focus.
3 Fine Adjustment of AF’s Point of FocusN When shooting with the intermediate range (focal length) of a zoom lens, the AF’s point of focus is corrected automatically relative to the adjustments made for the wide-angle and telephoto ends. Even if only the wide-angle or telephoto end is adjusted, a correction will be made automatically for the intermediate range.
When Autofocus Fails Autofocus may fail to achieve focus (focus indicator in the viewfinder blinks) with special subjects such as the following: Subjects Difficult to Focus Subjects with very low contrast (Example: Blue skies, solid-color flat surfaces, etc.) Subjects in very low light Strongly backlit or reflective subjects (Example: Cars with highly reflective bodies, etc.) Near and distant subjects framed close to an AF point (Example: Animals in cages, etc.
When Autofocus Fails MF: Manual Focus 1 Set the lens’s focus mode switch to . X <4 L> will be displayed on the LCD panel. Focusing ring on the subject. 2 Focus Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder. If you manually focus while pressing the shutter button halfway, the focus indicator will light up when focus is achieved. With Automatic selection AF, when the center AF point achieves focus, the focus indicator will light up.
i Selecting the Drive Mode Single and continuous drive modes are provided. You can select the drive mode suiting the scene or subject. 1 Press the button (9). the drive mode. 2 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. o( 160 ): High-speed continuous shooting While you hold down the shutter button completely, you can shoot continuously at approx. 7.0 shots/sec.
i Selecting the Drive Mode With the Digital Lens Optimizer set: When [Digital Lens Optimizer] is set to [Enable], the continuous shooting speed will greatly decrease. The maximum continuous shooting speed will vary depending on the shooting conditions. For details, see page 162. i : Low-speed continuous shooting While you hold down the shutter button completely, you can shoot continuously at approx. 3.0 shots/sec. maximum.
i Selecting the Drive Mode The approx. 7.0 shots/sec. maximum high-speed continuous shooting speed (p.160) is achieved under the following conditions: Fully charged battery pack, 1/500 sec. or faster shutter speed, maximum aperture (varies depending on the lens)*, at room temperature (23°C / 73°F), flicker reduction disabled, Dual Pixel RAW shooting disabled, Live View shooting with One Shot AF and Silent LV shooting both disabled, and Digital Lens Optimizer disabled.
j Using the Self-timer Use the self-timer when you want to be in the picture such as a commemorative photograph. 1 Press the button (9). the self-timer. 2 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial. Q : Shoot in approx. 10 sec. k : Shoot in approx. 2 sec. picture. 3 TakeLookthethrough the viewfinder, focus on the subject, then press the shutter button completely.
MEMO 164
4 Image Settings This chapter explains image-related function settings: Image-recording quality, Dual Pixel RAW function, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, noise reduction, highlight tone priority, lens aberration correction, anti-flicker shooting, and other functions. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: .
3 Selecting the Card for Recording and Playback If either a CF card or SD card is already inserted in the camera, you can start recording captured images. When only one card is inserted, you do not have to follow the procedures described on pages 166-168. If you insert both cards, you can select the recording method and select which card to use for recording and playing back images. [f] indicates the CF card, and [g] the SD card.
3 Selecting the Card for Recording and Playback Standard Images will be recorded to the card selected with [Record/play]. Auto switch card Same as with the [Standard] setting, but if the card becomes full, the camera will automatically switch to the other card to record images. When the card is automatically switched, a new folder will be created. Rec. separately You can set the image-recording quality for each card (p.169).
3 Selecting the Card for Recording and Playback Selecting the CF or SD Card for Recording and Playback If [Record func.] is set to [Standard] or [Auto switch card], select the card for recording and playing back images. If [Record func.] is set to [Rec. separately] or [Rec. to multiple], select the card for playing back images. Standard / Auto switch card Select [Record/play]. Select [Record/play], then press <0>. f : Record images to and play back images from the CF card.
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.173). 1 Standard / Auto switch card / Rec. to multiple Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording 2 Select quality. To select a RAW quality, turn the <6> dial. To select a JPEG quality, turn the <5> dial.
3 Setting the Image-Recording Quality Image-recording Quality Setting Examples 73 only 1 only 1+73 61+74 The image size [****x****] and number of possible shots [****] displayed on the Image-recording quality setting screen always apply to the [3:2] setting regardless of the [z5: Aspect ratio] setting (p.310). If [-] is set for both the RAW image and JPEG image, 73 will be set.
3 Setting the Image-Recording Quality Guide to Image-recording Quality Settings Image Pixels Quality Recorded Print Size File Possible Size Shots (MB) (Approx.) Maximum Burst CF Card SD Card High High Standard Standard Speed Speed JPEG 73 83 74 84 7a 30 M 13 M A2 A3 8.8 820 110 Full 130 4.5 1590 Full Full Full Full Full 4.7 1530 Full Full Full Full 2.4 2970 Full Full Full Full 3.0 2350 Full Full Full Full 1.5 4560 Full Full Full Full 7.5 M A4 b 2.
3 Setting the Image-Recording Quality The number of possible shots is based on Canon’s testing standards and an 8 GB card.
3 Setting the Image-Recording Quality RAW Images A RAW image is raw data output by the image sensor converted to digital data. It is recorded to the card as is, and you can select the quality as follows: 1, 41, or 61. A 1 image can be processed with [31: RAW image processing] (p.446) and saved as a JPEG image. (41 and 61 images cannot be processed with the camera.) As the RAW image itself does not change, you can process the RAW image to create any number of JPEG images with various processing conditions.
3 Setting the Image-Recording Quality One-touch Image Quality SettingN With Custom Controls, you can assign the image-recording quality to the button or depth-of-field preview button so you can switch to it momentarily. If you assign [One-touch image quality setting] or [One-touch image quality (hold)] to the button or depth-offield preview button, you can quickly switch to the desired imagerecording quality and shoot. For details, see “Custom Controls” (p.495).
Setting the Dual Pixel RAW Function If you shoot 1 images (other than 41 or 61) when Dual Pixel RAW function is set, they will be recorded as “special 1 images (Dual Pixel RAW images)” with Dual Pixel data from the image sensor appended. This is called Dual Pixel RAW shooting. When you perform processing of the Dual Pixel RAW image with the Digital Photo Professional (EOS software, p.
Setting the Dual Pixel RAW Function Even if [z1: Dual Pixel RAW] is set to [Enable], you cannot record 41 or 61 images appended with the Dual Pixel data (only possible with 1 images). If [51: Record func+card/folder sel.] is set to [Rec. separately] and the image-recording quality is set to 1 for one card and 41 or 61 for the other, Dual Pixel RAW shooting cannot be performed.
i: Setting the ISO Speed for Still PhotosN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In the mode, the ISO speed is automatically set (p.179). Regarding the ISO speed during movie shooting, see pages 337 and 341. 1 Press the button (9). the ISO speed. 2 SetWhile looking at the LCD panel or in the viewfinder, turn the <6> dial. ISO speed can be set within ISO 100 - ISO 32000 in 1/3-stop increments. “A” indicates ISO Auto.
i: Setting the ISO Speed for Still PhotosN As H1 (equivalent to ISO 51200) and H2 (equivalent to ISO 102400) are expanded ISO speed settings, noise (dots of light, banding, etc.) and irregular colors will be more noticeable, and the resolution lower compared with the standard setting. As L (equivalent to ISO 50) is an expanded ISO speed setting, the dynamic range will be somewhat narrower compared with the standard setting. If [z3: Highlight tone priority] is set to [Enable] (p.
i: Setting the ISO Speed for Still PhotosN ISO Auto If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode.
i: Setting the ISO Speed for Still PhotosN 3 Setting the Manually-Settable ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within L (equivalent to ISO 50) to H1 (equivalent to ISO 51200), and the maximum limit within ISO 100 to H2 (equivalent to ISO 102400). 1 Select [ISO speed settings]. Under the [z2] tab, select [ISO speed settings], then press <0>. 2 Select [Range for stills]. the minimum limit.
i: Setting the ISO Speed for Still PhotosN 3 Setting the ISO Speed Range for ISO Auto You can set the automatic ISO speed range for ISO Auto within ISO 100 - ISO 32000. You can set the minimum limit within ISO 100 - ISO 25600, and the maximum limit within ISO 200 - ISO 32000 in whole-stop increments. 1 Select [Auto range]. the minimum limit. 2 SetSelect the minimum limit box, then press <0>. Select the ISO speed, then press <0>. the maximum limit. 3 SetSelect the maximum limit box, then press <0>.
i: Setting the ISO Speed for Still PhotosN 3 Setting the Minimum Shutter Speed for ISO Auto You can set the minimum shutter speed so that the shutter speed set automatically will not be too slow when ISO Auto is set. This is effective in the and modes when you use a wideangle lens to shoot a moving subject or when you use a telephoto lens. It helps to reduce camera shake and blurred subjects. 1 Automatically set Manually set Select [Min. shutter spd.]. the desired minimum shutter 2 Set speed.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In the mode, the Picture Style is set automatically to [D] (Auto). 1 Press the button. [A]. 2 Select X The Picture Style selection screen will appear. a Picture Style. 3 Select X The Picture Style will be set and the camera will be ready to shoot. You can also set this with the [z3: Picture Style] screen.
A Selecting a Picture StyleN Picture Style Characteristics D Auto The color tone will be adjusted automatically to suit the scene. The colors will look vivid for blue skies, greenery and sunsets, particularly in nature, outdoor and sunset scenes. If the desired color tone is not obtained with [Auto], use another Picture Style. P Standard The image looks vivid, sharp, and crisp. This is a general-purpose Picture Style suitable for most scenes. Q Portrait For nice skin tones. The image looks softer.
A Selecting a Picture StyleN U Faithful Suited for processing the image with a computer. The color of a subject that is captured in sunlight at a color temperature of 5200K will be adjusted to match the subject’s colorimetrical color. For subdued images with modest brightness and color saturation. V Monochrome Creates black-and-white images. Black-and-white images shot in JPEG cannot be turned into color. Be careful not to leave the [Monochrome] setting on when you want to shoot photos in color again.
A Selecting a Picture StyleN Symbols The Picture Style selection screen has icons for [Strength], [Fineness], or [Threshold] for [Sharpness] as well as [Contrast], and other parameters. The numerals indicate the values for these parameters set for the respective Picture Style.
A Customizing a Picture StyleN You can customize the Picture Styles. You can change or adjust the parameter settings of Picture Styles such as [Strength], [Fineness], or [Threshold] for [Sharpness] as well as [Contrast] and other parameters from the default settings. To see the resulting effects, take test shots. To customize [Monochrome], see page 189. 1 Press the button. [A]. 2 Select X The Picture Style selection screen will appear. a Picture Style.
A Customizing a Picture StyleN the parameter. 5 SetAdjust the level of effect (parameter) as desired, then press <0>. Press the button to save the adjusted parameter settings. The Picture Style selection screen will reappear. X The value of parameter settings different from the default will be displayed in blue.
A Customizing a Picture StyleN V Monochrome Adjustment Besides the effects described on the preceding page such as [Contrast], or [Strength], [Fineness] and [Threshold] for [Sharpness], you can also set [Filter effect] and [Toning effect]. kFilter effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. Filter Sample Effects N: None Normal black-and-white image with no filter effects.
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. Useful when you want to preset multiple Picture Styles with different settings. You can also adjust the parameters of a Picture Style that is registered to the camera with EOS Utility (EOS software, p.598). 1 Press the button. [A]. 2 Select X The Picture Style selection screen will appear. [User Def.
A Registering a Picture StyleN a parameter. 6 Select Select the parameter (such as [Strength] of [Sharpness]) to be set, then press <0>. the parameter. 7 SetAdjust the level of effect (parameter) as desired, then press <0>. For details, see “Customizing a Picture Style” (p.187). Press the button to register the adjusted parameter settings. The Picture Style selection screen will then reappear. X The base Picture Style will be indicated on the right of [User Def. *].
B: Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the Auto [Q] (Ambience priority) or [Qw] (White priority) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with Auto, you can select the white balance to match the light source or set it manually by shooting a white object. In the mode, [Q] (Ambience priority) is automatically set. 1 Press the button (9). a white balance setting.
B: Setting the White BalanceN You can also set this with the [z2: White balance] screen. To switch between Auto [Q] (Ambience priority) and [Qw] (White priority), use the [z2: White balance] screen (p.194). White Balance To the human eye, a white object looks white regardless of the type of lighting. With a digital camera, the white for color correction basis is decided depending on the color temperature of the illumination, and then the color is adjusted with software to make the white areas look white.
B: Setting the White BalanceN Q Auto White Balance With [Q] (Ambience priority), you can increase the intensity of the image’s warm color cast when shooting a tungsten-light scene. If you select [Qw] (White priority), you can reduce the intensity of the image’s warm color cast. If you want to match the Auto white balance of previous EOS DIGITAL camera models, select [Q] (Ambience priority). 1 Select [White balance]. Under the [z2] tab, select [White balance], then press <0>. [Q].
B: Setting the White BalanceN O Custom White Balance With custom white balance, you can manually set the white balance for the specific light source of the shooting location. Make sure to perform this procedure under the light source at the actual location of the shoot. 1 Shoot a white object. Look through the viewfinder and aim the entire dotted line box (shown in the illustration) over a plain, white object. Focus manually and shoot with the standard exposure set for the white object.
B: Setting the White BalanceN 4 Press the button (9). the custom white balance. 5 Select Look at the LCD panel and turn the <5> dial to select . If the exposure obtained in step 1 differs greatly from the standard exposure, a correct white balance may not be obtained. In step 3, the following images cannot be selected: Images captured with the Picture Style set to [Monochrome], multiple-exposure images, frame-grab images from 4K movies, and images shot with another camera.
B: Setting the White BalanceN P Setting the Color Temperature You can set the white balance’s color temperature numerically. This is for advanced users. 1 Select [White balance]. Under the [z2] tab, select [White balance], then press <0>. the color temperature. 2 SetSelect [P]. Turn the <6> dial to set the color temperature, then press <0>. The color temperature can be set from approx. 2500 K to 10000 K in 100 K increments.
u White Balance CorrectionN You can correct the white balance that is set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users, particularly for those users who understand the use of color temperature conversion and color compensating filters and their effects. White Balance Correction 1 Select [WB Shift/Bkt.].
u White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images with different color tones can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias and magenta/green bias. This function is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
u White Balance CorrectionN During white balance bracketing, the maximum burst for continuous shooting will be lower. Since three images are recorded for one shot, it takes longer to record the image to the card. You can also set white balance correction and AEB together with white balance bracketing. If you set AEB in combination with white balance bracketing, a total of nine images will be recorded for a single shot. When white balance bracketing is set, the white balance icon will blink.
3 Auto Correction of Brightness and Contrast If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In the mode, [Standard] is automatically set. 1 Select [Auto Lighting Optimizer]. Under the [z2] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. When shooting at low ISO speeds, the noise in the darker parts of the image (shadow areas) can further be reduced. 1 Select [High ISO speed NR]. Under the [z3] tab, select [High ISO speed NR], then press <0>. the level. 2 SetSelect the desired noise reduction level, then press <0>.
3 Setting Noise ReductionN Cautions for Setting Multi Shot Noise Reduction If there is significant misalignment in the image due to camera shake, the noise reduction effect may become smaller. If you are handholding the camera, keep it steady to prevent camera shake. Using a tripod is recommended. If you shoot a moving subject, the moving subject may leave afterimages. The image alignment may not function properly with repetitive patterns (lattice, stripes, etc.) or flat, single-tone images.
3 Setting Noise ReductionN Long Exposure Noise Reduction For images exposed for 1 sec. or longer, noise (dots of light and banding) typical of long exposures can be reduced. 1 Select [Long exp. noise reduction]. Under the [z3] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetSelect the desired setting, then press <0>. Auto For exposures of 1 sec. or longer, noise reduction is performed automatically if noise typical of long exposures is detected.
3 Setting Noise ReductionN With [Auto] or [Enable] set, the noise reduction process after the picture is taken may take the same amount of time as that for the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1” or higher. Images taken at high ISO speeds may look grainier with the [Enable] setting than with the [Disable] or [Auto] setting.
3 Highlight Tone Priority You can reduce overexposed, clipped highlights. 1 Select [Highlight tone priority]. Under the [z3] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. picture. 3 TakeThetheimage will be recorded with highlight tone priority applied. When [Enable] is set, noise may increase slightly.
3 Correction of Lens Aberrations due to Optical CharacteristicsN Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the optical characteristics of the lens. Image distortion due to optical characteristics of the lens is called distortion. Color fringing along subject outlines is called chromatic aberration. And decreased image sharpness due to the aperture is called diffraction phenomenon. These lens aberrations can be corrected.
3 Correction of Lens Aberrations due to Optical CharacteristicsN [Enable]. 3 Select Check that [Correction data available] is displayed for the attached lens. Select [Enable], then press <0>. picture. 4 TakeThetheimage will be recorded with the peripheral illumination corrected. Depending on shooting conditions, noise may appear on the image periphery. The higher the ISO speed, the lower the correction amount will be.
3 Correction of Lens Aberrations due to Optical CharacteristicsN Distortion Correction 1 Select [Distortion correction]. [Enable]. 2 Select Check that [Correction data available] is displayed for the attached lens. Select [Enable], then press <0>. picture. 3 TakeThetheimage will be recorded with the distortion corrected. When distortion correction is enabled, the camera records an image range narrower than the one seen through the viewfinder.
3 Correction of Lens Aberrations due to Optical CharacteristicsN Digital Lens Optimizer 1 Select [Digital Lens Optimizer]. [Enable]. 2 Select Check that [Correction data available] is displayed for the attached lens. Select [Enable], then press <0>. picture. 3 TakeThetheimage will be recorded with the following being corrected: lens aberrations, diffraction phenomenon, and the deterioration of resolution caused by the low-pass filter.
3 Correction of Lens Aberrations due to Optical CharacteristicsN When [Digital Lens Optimizer] is set to [Enable], [Chromatic aberr corr] and [Diffraction correction] will not be displayed, but both will be set to [Enable] for shooting. The icon can be displayed in the viewfinder (p.84) by adding a checkmark [X] to [Digital Lens Optimizer] in [Viewfinder display]. The Digital Lens Optimizer’s correction data for newly released lenses can be added with EOS Utility (EOS software, p.598).
3 Correction of Lens Aberrations due to Optical CharacteristicsN Diffraction Correction 1 Select [Diffraction correction]. [Enable]. 2 Select Select [Enable], then press <0>. picture. 3 TakeThetheimage will be recorded with the diffraction corrected. Depending on shooting conditions, noise may be intensified with the effects of correction. The higher the ISO speed, the lower the correction amount will be. For movie shooting, [Diffraction correction] will not appear (correction is not possible).
3 Correction of Lens Aberrations due to Optical CharacteristicsN Lens Correction Data The lens correction data for lens aberration corrections is registered (stored) in the camera. With [Enable] selected, the peripheral illumination correction, distortion correction, Digital Lens Optimizer, chromatic aberration correction, and diffraction correction will be applied automatically. With EOS Utility (EOS software, p.598), you can check which lenses have their correction data registered in the camera.
3 Correction of Lens Aberrations due to Optical CharacteristicsN Cautions for Lens Correction Peripheral illumination correction, distortion correction, chromatic aberration correction, and diffraction correction cannot be applied to JPEG images already taken. When using a non-Canon lens, setting the corrections to [Disable] is recommended even if [Correction data available] is displayed.
3 Reducing FlickerN If you shoot an image with a fast shutter speed under a light source such as fluorescent light, the blinking of the light source causes flicker and the image may be vertically unevenly exposed. If continuous shooting is used under these conditions, uneven exposures or colors across the images may result.
3 Reducing FlickerN If the subject is against a dark background or if there is a bright light in the image, flicker may not be properly detected. Under certain special types of lighting, the camera may not be able to reduce the effects of the flicker even when is displayed. Depending on the light source, flicker may not be detected properly. If you recompose a shot, may appear and disappear intermittently.
3 Setting the Color SpaceN The range of reproducible colors is called “color space”. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In the mode, the color space is set automatically to [sRGB]. 1 Select [Color space]. Under the [z2] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>.
3 Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder 1 Select [Record func+card/folder sel.]. Under the [51] tab, select [Record func+card/folder sel.], then press <0>. 2 Select [Folder]. 3 Select [Create folder]. [OK]. 4 Select X A new folder with the folder number increased by one is created.
3 Creating and Selecting a Folder Selecting a Folder Lowest file number Number of images in folder Select a folder on the folder selection screen, then press <0>. X The folder where the captured images will be saved is selected. Subsequently captured images will be recorded into the selected folder. Folder name Highest file number Folders As with “100EOS5D” for example, the folder name starts with three digits (the folder number) followed by five alphanumeric characters.
3 Changing the File Name The file name has four alphanumeric characters followed by a four-digit (Example) BE3B0001.JPG image number (p.223) and extension. The first four alphanumeric characters are set upon factory shipment and unique to the camera. However, you can change them. With “User setting1”, you can change and register the four characters as desired.
3 Changing the File Name Input mode Operate the <5>, <6>, or <9> to move the and select the desired character. Then press <0> to enter it. By selecting [Az1], you can change the input mode. To cancel the text entry, press the button, then select [OK]. the setting. 4 ExitAfter entering the correct number of characters, press the button, then select [OK]. X The registered file name will be saved. the registered file name. 5 Select Select [File name], then press <0>.
3 Changing the File Name The first character cannot be an underscore “_”. User setting2 When you select the “*** + image size” registered with User setting2 and take pictures, the image-recording quality character will be automatically appended as the file name’s fourth character from the left.
3 File Numbering Methods The captured images are assigned a sequential four-digit file number from 0001 (Example) BE3B0001.JPG to 9999 and saved in one folder. You can File numbering change how the file number is assigned. 1 Select [File numbering]. Under the [51] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Select the desired setting, then press <0>. With [Manual reset] selected, selecting [OK] will reset the image numbering to 0001.
3 File Numbering Methods Auto Reset Restarts the file numbering from 0001 each time the card is replaced or a new folder is created. When you replace the card, create a folder, or switch the target card (such as f9g), the file numbering continues in sequence from 0001 for the images saved. This is useful if you want to organize images by cards or folders.
3 Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. 1 Select [Copyright information]. Under the [55] tab, select [Copyright information], then press <0>. the option to be set. 2 Select Select [Enter author’s name] or [Enter copyright details], then press <0>. text. 3 Enter Operate the <5>, <6>, or <9> to Character palette Input mode move the and select the desired character. Then press <0> to enter it.
3 Setting Copyright InformationN Checking the Copyright Information When you select [Display copyright info.] in step 2, you can check the [Author] and [Copyright] information that you entered. Deleting the Copyright Information When you select [Delete copyright information] in step 2, you can delete the [Author] and [Copyright] information. If the entry for “Author” or “Copyright” is long, it may not be displayed entirely when you select [Display copyright info.].
5 GPS Settings This chapter explains the camera’s built-in GPS settings. The EOS 5D Mark IV (WG) can receive satellite navigation signals from GPS satellites (USA), GLONASS satellites (Russia), and Quasi-Zenith Satellite System (QZSS) “Michibiki” (Japan). The GPS function is set to [Disable] by default. This manual uses the term “GPS” to refer to the satellite navigation function. When [GPS] is set to [Mode 1] (p.
GPS Features Geotagging Images Geotag information*1 (latitude, longitude, elevation) and coordinated universal time*2 can be appended to images. Shooting locations of geotagged images can be displayed on a map on a computer. *1: Certain travel conditions or GPS settings may cause inaccurate geotag information to be added to images. *2: Coordinated Universal Time, abbreviated as UTC, is essentially the same as Greenwich Mean Time.
GPS Features Viewing Images and Information on a Virtual Map With Map Utility (EOS software, p.598), you can view the shooting locations and the route traveled on a map displayed on a computer.
GPS Precautions Countries and Regions Permitting GPS Function Use Use of GPS function is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating GPS function regulations, visit the Canon Web site to check where the use is allowed. Note that Canon cannot be held liable for any problems arising from GPS function use in other countries and regions.
Acquiring GPS Signals To acquire GPS signals, take the camera outside where the sky is unobstructed. Face the top of the camera toward the sky while keeping your hands, etc. away from the camera top. When the signal acquisition conditions are good, it will take the camera approx. 30 sec. to 60 sec. to acquire the GPS satellite signals after you set [GPS] to [Mode 1] or [Mode 2]. Check that [r] is displayed on the LCD panel, then shoot. 1 Select [GPS settings].
Acquiring GPS Signals GPS Acquisition Status The GPS acquisition status is indicated by the [r] icon displayed on the camera’s LCD panel. Constant r: Signal acquired Blinking r: Signal not acquired yet When you shoot while [r] is constantly displayed, the image will be geotagged. When [Mode 1] is set, the camera will continue to receive GPS signals at regular intervals even when the power switch is set to <2>. Therefore, the battery will drain faster and fewer shots can be taken.
Acquiring GPS Signals Poor GPS Coverage Under the following conditions, the GPS satellite signal will not be properly acquired. As a result, the geotag information may not be recorded or inaccurate geotag information may be recorded. Indoors, underground, in tunnels or forests, between buildings, or in valleys. Near high-voltage power lines or mobile phones operating on the 1.5 GHz band. When the camera is left inside a bag, etc. When traveling a long distance.
Acquiring GPS Signals Viewing GPS Information 1 Check the [GPS] setting. Check that [GPS] is set to [Mode 1] or [Mode 2]. [GPS information display]. 2 Select X The GPS information will be displayed. the picture. 3 TakeWhen you shoot after GPS signal acquisition, the image will be geotagged. Generally, elevation is not as accurate as latitude and longitude due to the nature of GPS. The icon indicates signal conditions. When is displayed, the elevation is also recorded.
Acquiring GPS Signals Geotagging Information Play back the images and press the button to display the shooting information screen (p.398). Then tilt <9> up or down to check the geotag information. Latitude Longitude Elevation UTC (Coordinated Universal Time) When you shoot a movie, the GPS information at the time when shooting begins is recorded. Note that signal reception conditions are not recorded.
Setting the Positioning Interval The interval (time) to update the geotag information can be set. Although updating the geotag information at shorter intervals will record more accurate location information, it will reduce the number of possible shots because it will drain the battery faster. 1 Check the [GPS] setting. Check that [GPS] is set to [Mode 1] or [Mode 2]. 2 Select [Position update intvl]. the desired update interval. 3 SetSelect the desired update interval, then press <0>.
Setting Time from GPS on the Camera The time information obtained from GPS signals can be set on the camera. The margin of error is approx. ±1 sec. 1 Check the [GPS] setting. Check that [GPS] is set to [Mode 1] or [Mode 2]. 2 Select [Auto time setting]. the desired setting. 3 Select Select [Auto update] or [Set now], then press <0>. [Auto update] updates the time when the camera is turned on and a GPS signal is received.
Logging the Route Traveled When using the GPS logging function, the geotag information of the route the camera travels is automatically recorded in the camera’s internal memory. With Map Utility (EOS software, p.598), you can view the shooting locations and the route traveled on a map displayed on a computer. Map data ©2016 ZENRIN 1 Check the [GPS] setting. Check that [GPS] is set to [Mode 1] or [Mode 2]. 2 Select [GPS Logger]. [Log GPS position] to 3 Set [Enable].
Logging the Route Traveled Geotag Information Logs Geotag information for the route the camera travels is recorded at the intervals set with [Position update intvl] (p.236). The log data is saved in the camera’s internal memory by date. The table below shows how many days’ worth of data can be saved. Log Data Capacity by Positioning Interval (Approx.) Update Interval Log Data Update Interval Log Data Every 1 sec. 4.1 days Every 30 sec. 100 days Every 5 sec. 20 days Every 1 min.
Logging the Route Traveled Downloading Log Data to a Computer The log data in the camera’s internal memory can be downloaded to a computer with EOS Utility (EOS software, p.598) or downloaded from a card after transferring the data to the card. When you use Map Utility (EOS software, p.598) to open a log file saved on the computer, the camera’s travel route will be displayed on a map.
Logging the Route Traveled When connecting the camera to a computer, use the provided interface cable or one from Canon (p.525). When connecting the interface cable, use the provided cable protector (p.38). The GPS antenna is located at the top of the camera body. For this reason, even when carrying the camera, such as in a bag, try to keep the top of the camera facing upwards, and do not place anything on top of it. Set the camera time and date as accurately as possible.
MEMO 242
6 Advanced Operations for Photographic Effects In the , , , , and modes, you can change various settings of the camera as you desire to obtain a wide variety of shooting results, by selecting the shutter speed and/or aperture, adjusting the exposure as you prefer, etc. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: .
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . on the subject. 2 Focus Look through the viewfinder and aim the AF point over the subject. Then press the shutter button halfway. X When focus is achieved, the focus indicator in the viewfinder will light up (in One-Shot AF mode).
d: Program AE If the “30"” shutter speed and the lowest f/number blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the highest f/number blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and Modes In the mode, many functions, such as the AF operation and metering mode, are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure matching the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action of a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen motion (Fast shutter speed: 1/2000 sec.
s: Shutter-Priority AE If the lowest f/number blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the highest f/number blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure matching the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (higher f/number) until the shutter speed blinking stops or set a lower ISO speed. Aperture Value Display The higher the f/number, the smaller the aperture opening will be.
f: Aperture-Priority AE Depth-of-Field Preview The aperture opening (diaphragm) changes only at the moment when the picture is taken. Otherwise, the aperture remains fully open. Therefore, when you look at the scene through the viewfinder or on the LCD monitor, the depth of field will look narrow. Press the depth-of-field preview button to stop down the lens to the current aperture setting and check the depth of field (range of acceptable focus).
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. Shutter speed Aperture 1 Set the Mode Dial to . 2 Set the ISO speed (p.177). the shutter speed and 3 Set aperture. To set the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
a: Manual Exposure Exposure Compensation with ISO Auto If the ISO speed is set to A (AUTO) for manual exposure shooting, you can set exposure compensation (p.255) as follows: [z2: Expo.comp./AEB] Under [83: Custom Controls], with [ : Expo comp (hold btn, turn )] or [ : Expo comp (hold btn, turn )] (p.506). Quick Control (p.64) If ISO Auto is set, the ISO speed setting will change to obtain the standard exposure with the set shutter speed and aperture.
q Selecting the Metering ModeN You can select one of four methods to measure the subject brightness. In the mode, evaluative metering is set automatically. 1 Press the button (9). the metering mode. 2 Select While looking at the LCD panel or in the viewfinder, turn the <6> dial. q: Evaluative metering w: Partial metering r: Spot metering e: Center-weighted average metering q: Evaluative metering General-purpose metering mode suited even for backlit subjects.
q Selecting the Metering ModeN r: Spot metering Effective when metering a specific part of the subject or scene. Spot metering covers approx. 1.3% of the viewfinder area at the center. The spot metering circle will be displayed in the viewfinder. e: Center-weighted average metering The metering is averaged for the entire scene with the viewfinder center weighted more heavily.
O Setting the Desired Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the , , and shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3-stop increments for viewfinder shooting, the exposure compensation indicator in the viewfinder and on the LCD panel can display the setting only up to ±3 stops.
O Setting the Desired Exposure CompensationN For Live View and movie shooting, the exposure compensation can be set only up to ±3 stops. If [z2: Auto Lighting Optimizer] (p.201) is set to any setting other than [Disable], the image may still look bright even if a decreased exposure compensation for a darker image is set. The exposure compensation amount will remain in effect even after you set the power switch to <2>.
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three consecutive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z2] tab, select [Expo.comp./AEB], then press <0>. the AEB range. 2 SetTurn the <6> dial to set the AEB AEB range range. If you turn <5>, you can set the exposure compensation amount. Press <0> to set it.
h Auto Exposure Bracketing (AEB)N During AEB shooting, will blink in the viewfinder. If the drive mode is set to or , press the shutter button three times for each shot. When , , or is set and you hold down the shutter button completely, the three bracketed shots will be taken consecutively and the camera will automatically stop shooting. When or is set, the three bracketed shots will be taken consecutively after a 10-sec. or 2-sec. delay.
A Lock the Exposure for Shooting (AE Lock)N You can lock the exposure when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the picture. This is called AE lock. It is effective for shooting backlit subjects, etc. 1 Focus on the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button (0).
F: Long (Bulb) Exposures In this mode, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This photographic technique is called “bulb exposure”. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring long exposures. 1 Set the Mode Dial to . the desired aperture. 2 SetWhile looking at the LCD panel or the viewfinder, turn the <6> or <5> dial. picture.
F: Long (Bulb) Exposures With [z3: Long exp. noise reduction], you can reduce the noise generated during long exposures (p.204). For bulb exposures, using a tripod and bulb timer is recommended. You can also use mirror lockup (p.276) in combination. You can also shoot bulb exposures by using Remote Switch RS-80N3 or Timer Remote Controller TC-80N3 (each sold separately, p.279). You can also use Remote Controller RC-6 (sold separately, p.279) for bulb exposures.
F: Long (Bulb) Exposures the desired exposure time. 3 SetSelect the hour, minute, or second. Press <0> so is displayed. Set the desired number, then press <0> (Returns to ). [OK]. 4 Select X The set time will be displayed on the menu screen. X When you exit the menu, will be displayed on the LCD panel. the picture. 5 Take X Press the shutter button completely, Elapsed exposure time Bulb timer and the bulb exposure will start and continue until the set time elapses.
w: HDR (High Dynamic Range) ShootingN You can shoot still photos with clipped highlights and shadows reduced for a high dynamic range of tones even in high-contrast scenes. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured consecutively for each shot and then merged together automatically. The HDR image is recorded as a JPEG image. * HDR stands for High Dynamic Range.
w: HDR (High Dynamic Range) ShootingN Effects Natural For images preserving a wide tonal range where the highlight and shadow details would otherwise be lost. Clipped highlights and shadows will be reduced. Art standard While the clipped highlights and shadows will be reduced more than with [Natural], the contrast will be lower, and the gradation flatter to have the picture look like a painting. The subject outlines will have bright (or dark) edges.
w: HDR (High Dynamic Range) ShootingN [Continuous HDR]. 5 SetSelect either [1 shot only] or [Every shot], then press <0>. With [1 shot only], HDR shooting will be canceled automatically after the shooting ends. With [Every shot], HDR shooting continues until the setting in step 3 is set to [Disable HDR]. Image Align]. 6 SetFor[Auto handheld shooting, select [Enable]. When using a tripod, select [Disable], then press <0>. to be saved.
w: HDR (High Dynamic Range) ShootingN picture. 8 TakeHDRtheshooting is possible with viewfinder shooting and Live View shooting. When you press the shutter button completely, three consecutive images will be captured, and the HDR image will be recorded to the card. If the image-recording quality is set to RAW, the HDR image will be recorded in 73 quality. If the image-recording quality is set to RAW+JPEG, the HDR image will be recorded in the JPEG quality set.
w: HDR (High Dynamic Range) ShootingN When shooting HDR images with [Auto Image Align] set to [Enable], AF point display information (p.402) and Dust Delete Data (p.460) will not be appended to the image. If you perform handheld HDR shooting with [Auto Image Align] set to [Enable], image periphery will be slightly trimmed and resolution will be slightly lowered. Also, if the images cannot be aligned properly due to camera shake, etc., auto image alignment may not take effect.
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. With Live View shooting (p.297), you can see in real time how the exposures are merged when you shoot multiple-exposure images. 1 Press the button. Multiple exposure. 2 Select Select [P], then press <0>. X The multiple exposure setting screen will appear. [Multiple exposure]. 3 SetSelect [On:Func/Ctrl] or [On:ContShtng], then press <0>. To exit shooting multiple exposures, select [Disable].
P Multiple ExposuresN [Multi-expos ctrl]. 4 SetSelect the desired multiple-exposure control method, then press <0>. Additive The exposure of each single image captured is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Follow the basic guide below to set the exposure compensation amount. Exposure Compensation Setting Guide by Number of Exposures Two exposures: -1 stop, three exposures: -1.5 stop, four exposures: -2 stops Average Based on the [No.
P Multiple ExposuresN to be saved. 6 SetTothesaveimages all the single exposures and the merged multiple-exposure image, select [All images], then press <0>. To save only the merged multipleexposure image, select [Result only], then press <0>. [Continue Mult-exp]. 7 SetSelect either [1 shot only] or [Continuously], then press <0>. With [1 shot only], multiple-exposure shooting will be canceled automatically after the shooting ends.
P Multiple ExposuresN subsequent exposures. 9 Shoot X When [On:Func/Ctrl] is set, the merged multiple-exposure image will be displayed. Live View shooting with [On:Func/ Ctrl] set, the multiple-exposure images merged so far will be displayed. By pressing the button, you can display only the Live View image. Multiple-exposure shooting will end when the set number of exposures are taken.
P Multiple ExposuresN The image-recording quality, ISO speed, Picture Style, high ISO speed noise reduction, color space, etc. set for the first single exposure will also be set for the subsequent exposures. During multiple-exposure shooting, the settings will be automatically switched to [Disable] for the following: all the items of [z1: Lens aberration correction], [z2: Auto Lighting Optimizer], and [z3: Highlight tone priority].
P Multiple ExposuresN Merging Multiple Exposures with an Image Recorded on the Card You can select a 1 image recorded on the card as the first single exposure. The image data of the selected 1 image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images. 1 Select [Select image for multi. expo.]. X The images on the card will be displayed. the first image. 2 Select Turn the <5> dial to select the image to be used as the first single exposure, then press <0>. Select [OK].
P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single exposure. If you select [Deselect img], the image selection will be canceled. Checking and Deleting Multiple Exposures During Shooting When [On:Func/Ctrl] is set and you have not finished shooting the set number of exposures, you can press the button to check the current exposure level, overlap alignment, and overall effect of the merged multipleexposure image. (Not possible when [On:ContShtng] is set.
P Multiple ExposuresN FAQ Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure image will be saved as a 1 image. Image Quality Setting Single Exposures Merged Multiple-Exposure JPEG JPEG JPEG 1 1 1 41/61 41/61 1 1+JPEG 1+JPEG 1+JPEG 41/61+JPEG 41/61+JPEG 1+JPEG Can I merge images recorded on the card? With [Select image for multi. expo.
2 Mirror LockupN Camera vibrations caused by the mirror’s reflex action when the picture is taken is called “mirror shock”. Mirror lockup keeps the mirror up before and during exposure to reduce blur caused by camera vibrations. Useful when shooting close-ups (macro photography), using a super telephoto lens, shooting at slow shutter speeds, etc. 1 Select [Mirror lockup]. Under the [z4] tab, select [Mirror lockup], then press <0>. 2 Select [Enable].
2 Mirror LockupN Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components. When shooting with mirror lockup in very bright light, such as at the beach or a ski slope on a sunny day, take the picture promptly after mirror lockup is stabilized. During mirror lockup, shooting function settings and menu operations are disabled.
Using the Eyepiece Cover When you take a picture without looking through the viewfinder, such as when you use the self-timer, bulb exposure, or a remote switch, stray light entering the viewfinder may cause the picture to look dark (underexposed). To prevent this, use the eyepiece cover (p.37) attached to the camera strap. Note that attaching the eyepiece cover is not necessary in Live View shooting or movie shooting. 1 Detach the eyecup.
Using a Remote Switch You can connect any EOS accessory equipped with an N3-type terminal such as the Remote Switch RS-80N3 or Timer Remote Controller TC80N3 (each sold separately) to shoot with the camera (p.525). To operate the accessory, refer to its Instruction Manual. 1 Open the terminal cover. the plug to the remote 2 Connect control terminal. Connect the plug as shown in the illustration. To disconnect the plug, grasp the silver part and pull it out.
R Remote Control Shooting the self-timer/remote 4 Select controller. Look at the LCD panel or in the viewfinder and turn the <5> dial to select or . the remote controller’s 5 Press transmit button. Remote control sensor Point the remote controller toward the camera’s remote control sensor, then press the transmit button. X The self-timer lamp lights up and the picture is taken. Fluorescent or LED lighting may cause camera misoperation by triggering the shutter inadvertently.
H Interval Timer Shooting With the interval timer, you can set the shooting interval and the number of shots. The camera will repeat taking one shot with the set interval until the set number of shots are taken. 1 Select [Interval timer]. Under the [z4] tab (the [z2] tab in mode), select [Interval timer], then press <0>. [Enable]. 2 Select Select [Enable], then press the button. the shooting interval and 3 Set number of shots.
H Interval Timer Shooting Shooting interval Number of shots [OK]. 4 Select X The interval timer settings will be displayed on the menu screen. X When you exit the menu, will be displayed on the LCD panel. Interval timer the picture. 5 Take X First shot is taken and shooting continues according to the interval timer settings. During interval timer shooting, will blink. After the set number of shots are taken, the interval timer shooting will stop and be automatically canceled.
H Interval Timer Shooting Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components. If the lens’s focus mode switch is set to , the camera will not shoot when focus is not achieved. Setting it to and focusing manually is recommended. Live View shooting, movie shooting, or bulb exposures cannot be performed with interval timer.
MEMO 284
7 Flash Photography This chapter explains how to shoot with external EXseries Speedlites (sold separately) and how to set Speedlite settings on the camera’s menu screen.
D Flash Photography EOS-dedicated, EX-series Speedlites Using an EX-series Speedlite (sold separately) makes flash photography easy. For detailed instructions, refer to the EX-series Speedlite’s Instruction Manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions on the camera’s menu screen, see pages 289-295.
D Flash Photography If [z2: Auto Lighting Optimizer] (p.201) is set to any setting other than [Disable], the image may still look bright even if a decreased flash exposure compensation for a darker image is set. If it is difficult to achieve focus with autofocus, the EOS-dedicated, external Speedlite will automatically emit the AF-assist beam as necessary.
D Flash Photography Non-Canon Flash Units Sync Speed The camera can synchronize with non-Canon compact flash units at 1/200 sec. and slower speeds. With large studio flash units, the flash duration is longer than that of a compact flash unit and varies depending on the model. Be sure to check before shooting if flash sync is properly performed by test shooting at a sync speed of approx. 1/60 sec. to 1/30 sec. PC Terminal The camera’s PC terminal can be used with flash units having a sync cord.
3 Setting the Flash FunctionN With an EX-series Speedlite having compatible flash function settings, you can use the camera’s menu screen to set the Speedlite’s functions and Custom Functions. Attach the Speedlite to the camera and turn on the Speedlite before setting the flash functions. For details on the Speedlite’s functions, refer to the Speedlite’s Instruction Manual. 1 Select [External Speedlite control]. Under the [z1] tab, select [External Speedlite control], then press <0>.
3 Setting the Flash FunctionN Flash Sync. Speed in Av Mode You can set the flash-sync speed for flash photography in the aperturepriority AE mode. : Auto The flash sync speed is set automatically within a range of 1/200 sec. to 30 sec. to suit the scene’s brightness. High-speed sync is also possible. : 1/200-1/60sec. auto Prevents a slow shutter speed from being set in low-light conditions. It is effective for preventing subject blur and camera shake.
3 Setting the Flash FunctionN Flash Function Settings The screen display and setting options will vary depending on the Speedlite model, current flash mode, Speedlite’s Custom Function settings, etc. For details on the Speedlite’s functions, refer to the Speedlite’s Instruction Manual.
3 Setting the Flash FunctionN Wireless functions / Flash ratio control Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the Instruction Manual of a Speedlite compatible with wireless flash shooting. With a macro flash (MR-14EX II, etc.) compatible with flash function settings, you can set the flash ratio between flash tubes or flash heads A and B, or use wireless flash with additional slave units.
3 Setting the Flash FunctionN Shutter synchronization Normally, set this to [First-curtain synchronization] so that the flash fires immediately after the exposure starts. If [Second-curtain synchronization] is set, the flash will be fired right before the shutter closes. When this is combined with a slow shutter speed, you can create a trail of light such as from car headlights at night with a more natural feel.
3 Setting the Flash FunctionN When using second-curtain synchronization, set the shutter speed to 1/25 sec. or slower. If the shutter speed is 1/30 sec. or faster, first-curtain synchronization will be applied automatically even if [Second-curtain synchronization] is set. With an EX-series Speedlite not compatible with flash function settings, you can only set the following: [Flash firing], [E-TTL II meter.], and [Flash exposure compensation] under [Flash function settings].
3 Setting the Flash FunctionN Clearing Flash Function Settings / Flash C.Fn Settings 1 Select [Clear settings]. the settings to be cleared. 2 Select Select [Clear flash settings] or [Clear all Speedlite C.Fn’s], then press <0>. On the confirmation dialog, select [OK]. Then the flash settings or Custom Function settings will all be cleared. The Speedlite’s Personal Function (P.Fn) cannot be set or canceled on the camera’s [External Speedlite control] screen. Set it directly on the Speedlite.
MEMO 296
8 Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the image on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . If you handhold the camera and shoot while viewing the LCD monitor, camera shake may cause blurred images. Using a tripod is recommended in such cases. Remote Live View Shooting With EOS Utility (EOS software, p.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. X The Live View image will appear on the LCD monitor. The Live View image will be displayed in the brightness level closely matching that of the actual image to be captured. the shooting mode. 3 Select Turn the Mode Dial to select the shooting mode. on the subject.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [z5: Live View shoot.] (the [z3] tab in mode) to [Enable]. Number of Possible Shots with Live View Shooting (Approx. number of shots) Temperature Room Temperature (23°C / 73°F) Low Temperatures (0°C / 32°F) Possible shots 300 280 The figures above are based on a fully-charged Battery Pack LP-E6N and CIPA (Camera & Imaging Products Association) testing standards.
A Shooting with the LCD Monitor Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components. “General Live View Shooting Cautions” are on pages 331-332. The image’s field of view is approx. 100% (with image-recording quality set to JPEG 73 and aspect ratio set to 3:2).
A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change.
A Shooting with the LCD Monitor Warnings Do not hold the camera in the same position for long periods of time. Even if the camera does not feel too hot, prolonged contact with the same body part may cause skin redness or blistering due to low-temperature contact burns. Using a tripod is recommended for people with circulation problems or very sensitive skin, or when using the camera in very hot places. The histogram can be displayed when [z5: Expo. simulation] is set to [Enable] (p.311).
A Shooting with the LCD Monitor Scene Icons In the shooting mode, the camera detects the scene type and sets everything automatically to suit the scene. The detected scene type is indicated on the upper left of the screen.
A Shooting with the LCD Monitor *3: The icon of the scene selected from the detectable scenes will be displayed. *4: Displayed when all the following conditions apply: The shooting scene is dark, it is a night scene, and the camera is mounted on a tripod. *5:Displayed with any of the lenses below: EF300mm f/2.8L IS II USM EF400mm f/2.8L IS II USM EF500mm f/4L IS II USM EF600mm f/4L IS II USM Image Stabilizer lenses released in or after 2012.
A Shooting with the LCD Monitor B Button Display Options You can set the information to be displayed on the image for when you press the button during Live View shooting or movie shooting. Select [zbutton LV display options]. Under the [53] tab, select [zbutton LV display options], then press <0>. Live View info switch setting 1 Select [Live View info switch setting]. a number. 2 Select The numbers indicate the number of times to press the button.
A Shooting with the LCD Monitor the options. 3 EditSelect what you want to be displayed and press <0> to add a checkmark [X]. For the information you do not want to be displayed, press <0> to remove the checkmark [X]. Select [OK] to register the setting. Repeat steps 2 and 3 as necessary. Histogram display • Brightness/RGB The histogram (p.402) to be displayed when you press the button can be either the [Brightness] or [RGB] histogram.
Shooting Function Settings B/q/R/f/y/i/A/P/w Settings When the Live View image is displayed, if you press the , , , or button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function. By pressing the button and then the button, you can set white balance shift and white balance bracketing. After you press the button and select or , the menu screen for Multiple exposure or HDR mode will appear.
Shooting Function Settings Q Quick Control In the , , , , and modes, you can set the AF method, AF operation, Drive mode, Metering mode, Recording/ playing back card and image quality, White balance, Picture Style, and Auto Lighting Optimizer. In the mode, only the functions in bold above can be set. 1 2 Press the button (7). X The settable functions will be displayed. Select a function and set it. Use <9> to select a function.
3 Menu Function Settings z5 When the Live View shooting/Movie shooting switch is set to , menu options exclusive to the Live View shooting will appear under the [z5] and [z6] tabs (the [z3] tab in mode). The settable functions on this menu screen apply only to Live View shooting. They do not work with viewfinder shooting (settings are disabled). Live View shooting You can set Live View shooting to [Enable] or [Disable].
3 Menu Function Settings Aspect ratioN The image’s aspect ratio can be set to [3:2], [4:3], [16:9], or [1:1]. The area surrounding the Live View image is masked in black when the following aspect ratios are set: [4:3] [16:9] [1:1]. JPEG images will be saved with the set aspect ratio. RAW images will always be saved with the [3:2] aspect ratio.
3 Menu Function Settings Exposure simulationN Exposure simulation simulates and displays how the brightness (exposure) of the actual image will look. • Enable (g) The displayed image brightness will be close to the actual brightness (exposure) of the resulting image. If you set exposure compensation, the image brightness will change accordingly. • During e Normally, the image is displayed at the standard brightness to make the Live View image easy to see (E).
3 Menu Function Settings z6N Silent LV shootingN • Mode 1 Mechanical sound during shooting is suppressed, compared with viewfinder shooting. Continuous shooting is also possible. • Mode 2 When the shutter button is pressed completely, only one shot will be taken. While you keep holding down the shutter button, the camera operation will be suspended. Then when you return to the shutter button’s halfway position, the camera operation will resume.
3 Menu Function Settings With [Mode 2] set, continuous shooting will not work even if you set the drive mode to or . If you use flash with the flash mode set to E-TTL II/E-TTL autoflash, shutter release will be performed by the same internal operation mechanism as with viewfinder shooting. Therefore, shooting while suppressing the mechanical sound will not be possible (regardless of the [Silent LV shoot.] setting). When using a non-Canon flash unit, set it to [Disable].
Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In the mode, [One Shot AF] is set automatically. 1 Press the button. the AF operation. 2 Select Turn the <6> dial to select the desired AF operation, then press <0>. X: One-Shot AF K: Servo AF Settable only for Live View shooting (not settable for movie shooting). If focus cannot be achieved, the AF point will turn orange.
Selecting the AF OperationN Servo AF for Moving Subjects This AF operation is suited for moving subjects. While you hold down the shutter button halfway, the camera will keep focusing on the subject continuously. When the drive mode is set to for high-speed continuous shooting, the maximum continuous shooting speed will be approx. 4.3 shots/sec. The pictures will be taken with priority given to the continuous shooting speed.
Focusing with AF (AF Method) Selecting the AF Method You can set the AF method to [u+Tracking] (p.317), [FlexiZone Multi] (p.319), or [FlexiZone - Single] (p.321) to suit the shooting conditions and subject. If you want to achieve precise focus, set the lens’s focus mode switch to , magnify the image, and focus manually (p.329). Select the AF method. Under the [z5] tab (the [z3] tab in mode), select [AF method]. Select the desired AF method, then press <0>.
Focusing with AF (AF Method) u(face)+Tracking: c The camera detects and focuses on human faces. If a face moves, the AF point
also moves to track the face. 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. an AF point. 2 Select When a face is detected, the area Area frame frame will be displayed and
will appear over the face to be focused on. If multiple faces are detected, will be displayed.
Focusing with AF (AF Method) the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.298). Focusing on a subject other than a human face • Tap on the subject (or spot) where you want to focus. • Press <9> or <0> and the AF point < > will appear on the screen. Then use <9> to move the AF point over the target subject. • Once the AF point < > achieves focus, it will track the subject even if the subject moves or if you change the composition.
Focusing with AF (AF Method) FlexiZone - Multi: o You can use up to 63 AF points for wide-area focusing (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection). 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. Area frame the AF point.N 2 Select Pressing <9> or <0> will toggle Zone frame between automatic selection and zone selection. In the mode, automatic selection is set automatically.
Focusing with AF (AF Method) on the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. X When focus is achieved, the AF point will turn green and the beeper will sound. X If focus is not achieved, the area frame will turn orange. the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.298).
Focusing with AF (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus on a particular subject. the Live View image. 1 Display Press the <0> button. AF point X The Live View image will appear on the LCD monitor. X The AF point < > will appear. If [Movie servo AF] is set to [Enable], the AF point will be displayed larger. the AF point. 2 Move Use <9> to move the AF point to where you want to focus.
Focusing with AF (AF Method) the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.298).
Focusing with AF (AF Method) Notes for AF AF Operation Even when focus is achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation. Depending on the subject and shooting conditions, it may take longer to focus or the continuous shooting speed may decrease. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult.
Focusing with AF (AF Method) Shooting Conditions that Make Focusing Difficult Subject with low-contrast such as the blue sky, solid-color flat surfaces or when highlight or shadow details are clipped. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Subjects with repetitive patterns (Example: Skyscraper windows, computer keyboards, etc.). Fine lines and subject outlines. Under a light source whose brightness, color, or pattern keeps changing.
Focusing with AF (AF Method) Magnified View In the [FlexiZone - Multi] and [FlexiZone - Single] modes, either press the button or tap on [d] displayed on the bottom right of the screen. You can magnify the image by approx. 5x or 10x and check the focus. Magnified view is not possible with [u+Tracking]. To move the AF point or select a zone, operate <9> or tap on the spot you want to magnify. Either press the button or tap on [d] to magnify the image.
Focusing with AF (AF Method) If focusing is difficult in the magnified view, return to the normal view and perform AF. If you perform AF in the normal view and then the view is magnified, accurate focus may not be achieved. AF speed differs between normal view and magnified view. When in magnified view, Movie Servo AF (p.380) will not work. During magnified view, achieving focus becomes more difficult due to camera shake. Using a tripod is recommended.
x Shooting with the Touch Shutter Just by tapping on the LCD monitor screen, you can focus and take the picture automatically. 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. the touch shutter. 2 Enable Tap [y] on the screen’s bottom left. Each time you tap on the icon, it will toggle between [y] and [x]. [x] (Touch shutter: Enable) The camera will focus on the spot you tap on, then the picture will be taken.
x Shooting with the Touch Shutter Even if you set the drive mode to or , the camera will still shoot in single shooting mode. Even if [AF operation] is set to [Server AF], tapping on the screen will focus on the image with [One-Shot AF]. Tapping on the screen in magnified view will not focus or take the picture. In the mode, if [FlexiZone - Multi] or [yTouch shutter: Disable] is set, focusing cannot be performed by tapping on the screen.
MF: Focusing Manually You can magnify the image and focus precisely with MF (manual focus). 1 Set the lens’s focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame. 2 Display Press the button or tap on [d] on the lower right of the screen. X The magnifying frame will appear. Magnifying frame the magnifying frame. 3 Move Either operate <9> or tap on the spot you want to magnify to move the magnifying frame to where you want to focus.
MF: Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 TakeCheck the exposure, then press the shutter button completely to take the picture (p.298). In magnified view, the exposure is locked. (Shutter speed and aperture will be displayed in red.) Even with manual focusing, you can use the touch shutter to take a picure.
General Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a prolonged period, the camera’s internal temperature may rise, and image quality may deteriorate. Always exit Live View shooting when you are not shooting.
General Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. Even if a low ISO speed is set, noise may be noticeable in the displayed Live View image under low light. However, when you shoot, the image recorded will have less noise. (The image quality of the Live View image is different from that of the recorded image.) If the light source (illumination) within the image changes, the screen may flicker.
9 Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . Before shooting movies, see page 356 and make sure the card is able to record movies at the desired movierecording quality setting. If you handhold the camera and shoot movies, camera shake can cause blurred movies. Using a tripod is recommended in such cases. Full HD 1080 Full HD 1080 indicates compatibility with HighDefinition featuring 1080 vertical pixels (scanning lines).
k Shooting Movies / Autoexposure Shooting When the shooting mode is set to , , or , autoexposure control will take effect to suit the scene’s current brightness. the Mode Dial to , , 1 orSet. the Live View shooting/Movie 2 Set shooting switch to . X The Live View image will appear on the LCD monitor. on the subject. 3 Focus Before shooting a movie, focus with AF or manual focus (p.316, 329). When you press the shutter button halfway, the camera will focus with the current AF method.
k Shooting Movies Shutter-priority AE When the shooting mode is , you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain the standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired shutter speed. 3 SetWhile looking at the LCD monitor, turn the <6> dial. The settable shutter speeds depend on the frame rate. See page 343.
k Shooting Movies Aperture-priority AE When the shooting mode is , you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be set automatically to suit the brightness and obtain the standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired aperture. 3 SetWhile looking at the LCD monitor, turn the <6> dial. Aperture 4 Focus and shoot the movie.
k Shooting Movies ISO Speed in the Mode L: Full HD movie/w: High frame rate movie shooting The ISO speed will be set automatically within ISO 100 - ISO 25600. H: 4K movie shooting The ISO speed will be set automatically within ISO 100 - ISO 12800. ISO Speed in the , , , and Modes L: Full HD movie/w: High frame rate movie shooting The ISO speed will be set automatically within ISO 100 - ISO 25600.
k Shooting Movies Notes for , , , , and Modes In the mode, the scene icon for the scene detected by the camera is displayed on the upper left of the screen (p.339). You can lock the exposure (AE lock) by pressing the button (except in the A mode, p.259). After applying AE lock during movie shooting, you can cancel it by pressing the button. (AE lock setting is retained until you press the button.
k Shooting Movies Scene Icons During movie shooting in the mode, an icon representing the scene detected by the camera will be displayed, and the shooting will be performed to suit the scene. Subject Portrait*1 Background Non-Portrait Nature and Outdoor Scene Close*2 Background Color Bright Gray Backlit Blue Sky Included Light blue Backlit Sunset *3 *3 Orange Spotlight Dark blue Dark *1: Displayed only when the AF method is set to [u+Tracking].
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set it. For details on the ISO speed, see the next page. the shutter speed and 4 Set aperture.
k Shooting Movies ISO Speed in the Mode L: Full HD movie/w: High frame rate movie shooting With [AUTO] (A), the ISO speed will be set automatically within ISO 100 - ISO 25600. In [Range for movies] under [z2: ISO speed settings], if you set [Maximum] to [H2 (102400)] (p.379), the maximum limit of automatic ISO speed setting range will be expanded to H2 (equivalent to ISO 102400).
k Shooting Movies For movie shooting, the ISO speed cannot be expanded to L (equivalent to ISO 50). When switching from still photo shooting to movie shooting, check the ISO speed settings again before shooting movies. During movie shooting, avoid changing the shutter speed or aperture. Doing so may record the changes in the exposure or create more noise at high ISO speeds. When shooting a movie of a moving subject, a shutter speed of approx. 1/25 sec. to 1/125 sec. is recommended.
k Shooting Movies Settable Shutter Speeds The settable shutter speeds in the shutter-priority AE and manual exposure shooting modes vary depending on the frame rate of the movie-recording quality. (sec.
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies When the [AF method] is [FlexiZone - Multi] or [FlexiZone - Single], you can press the button to display the electronic level (p.82). You can set what is displayed when you press the button (p.305). If [AF method] is set to [u+Tracking] or if the camera is connected to a TV set with an HDMI cable, the electronic level will not be displayed. The electronic level, grid lines, or histogram cannot be displayed during movie shooting.
k Shooting Movies Cautions for Movie Shooting Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components. If you shoot something that has fine detail, moire or false colors may result. Under [51: Record func+card/folder sel.], even if [Record func.] is set to [Rec. to multiple] (p.167), the movie cannot be recorded to both the CF card [f] and SD card [g]. Note that if [Rec.
k Shooting Movies Warnings Do not hold the camera in the same position for long periods of time. Even if the camera does not feel too hot, prolonged contact with the same body part may cause skin redness or blistering due to low-temperature contact burns. Using a tripod is recommended for people with circulation problems or very sensitive skin, or when using the camera in very hot places. “General Movie Shooting Cautions” are on pages 391-392.
k Shooting Movies Final Image Simulation Final image simulation is a function that shows the movie as it will look with the current settings for Picture Style, white balance and other shooting functions applied. During movie shooting, the image displayed will automatically show the effects of the settings listed below. Final Image Simulation for Movie Shooting Picture Style * Sharpness (Strength), contrast, color saturation, and color tone will be reflected.
Shooting Function Settings B/i/A Settings If you press the , , or button with the image displayed on the LCD monitor, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective function. During manual-exposure shooting (p.340), you can press the button to set the ISO speed. By pressing the button and then the button, you can set white balance shift.
Shooting Function Settings Q Quick Control In the , , , , and modes, AF method, Movie recording size, Recording level (manual setting only), Sound volume (headphones), Card selection, White balance, Picture Style, Auto Lighting Optimizer, and HDR movie shooting can be set. In the mode, only the functions in bold above can be set. 1 2 Press the button (7). X The settable functions will be displayed. Select a function and set it. Use <9> to select a function.
3 Setting the Movie Recording Quality With [z4: Movie rec quality] (or the [z2] tab in the mode), you can set the movie recording format, movie recording size (size, frame rate, video format/compression method), and other functions. The frame rate displayed on the [Movie rec. size] screen switches automatically depending on the [53: Video system] setting (p.549). The card’s writing and reading speeds required for recording movies vary depending on the movie-recording quality.
3 Setting the Movie Recording Quality Movie Recording Size You can select the movie’s size, frame rate, and compression method. Image Size H 4096x2160 The movie will be recorded in 4K quality. The aspect ratio is approx. 17:9. To shoot H65/ 4J movies, use a high-speed CF card supporting UDMA 7 (p.356). L 1920x1080 The movie will be recorded in Full High-Definition (Full HD) quality. The aspect ratio is 16:9. w 1280x720 High Frame Rate movies (p.358) will be recorded in highdefinition (HD) quality.
3 Setting the Movie Recording Quality 4K movie shooting Shooting 4K movies requires a high-performance card. For details on card requirements for movie shooting, see “Cards that Can Record Movies” on page 356. Shooting 4K movies or High Frame Rate movies greatly increases the processing load. Compared with normal movie shooting, the camera’s internal temperature may increase faster or may become higher. If the red E icon appears during movie shooting, it indicates that the card may be hot.
3 Setting the Movie Recording Quality For 4K movie shooting, [z3: High ISO speed NR] will not take effect. Therefore, noise may be more noticeable depending on the shooting conditions. If you change the [53: Video system] setting, also set the movierecording size again. Movies shot in 4K, L8/7, or at a high frame rate may not be played back properly on other devices due to the heavy data processing load during playback.
3 Setting the Movie Recording Quality Movie recording method/Compression rate J MJPG Selectable when the movie recording format is [MOV]. Motion JPEG is used to compress the movie for recording. Without any compression between frames, each frame is compressed at a time and recorded. The compression rate is therefore low. Also, since the image size is large with 4K quality, the file size will be large. W ALL-I (For editing/I-only) Selectable when the movie recording format is [MOV].
3 Setting the Movie Recording Quality Cards that Can Record Movies When shooting movies, use a large-capacity card with a reading/writing speed (required card performance) shown in the table or higher than the standard specification. Test the card by taking a few movies in the desired quality (p.351) and make sure the card can properly record the movie. Movie Recording Quality H L w CF Card SD card UHS-I Speed Class 3 or higher 65B4 J UDMA 7 100 MB/sec. or faster 87 W UDMA 7 60 MB/sec.
3 Setting the Movie Recording Quality To optimize the use of the card, formatting the card with the camera before shooting movies is recommended (p.73). To check the card’s reading/writing speed, refer to the card manufacturer’s Web site. For bit rates, see page 580. 24.00p Records the movie at a frame rate of 24.00 fps. When [Enable] is set, you can select the movie-recording quality as follows: HBJ, LBW, or LBX. If you have set [Movie rec. size] and then set [24.00p] to [Enable], set the [Movie rec.
3 Setting the Movie Recording Quality High Frame Rate At HD quality, you can shoot movies at a high frame rate of 119.9 fps or 100.0 fps. Good for shooting movies to be played back in slow motion. The maximum recording time of one movie clip is 7 min. 29 sec. The movie will be recorded as w2 W D or w3 W D. Movie Servo AF will not work for high frame rate movie shooting. Also, during high frame rate movie shooting, AF will not work. High Frame Rate movies do not record sound.
3 Setting the Movie Recording Quality Total Movie Recording Time and File Size Per Minute In MOV Format Movie Recording Quality (Approx.) Total Possible Recording Time on Card File Size 8 GB 32 GB 128 GB 2 min. 8 min. 34 min. 3587 MB/min. 1298 MB/min. H: 4K 65B4 J L: Full HD 87 W 5 min. 23 min. 94 min. 87 X 17 min. 69 min. 277 min. 440 MB/min. 65B4 W 11 min. 46 min. 186 min. 654 MB/min. 65B4 X 33 min. 135 min. 541 min. 225 MB/min. HDR movie shooting 33 min. 135 min.
3 Setting the Movie Recording Quality Movie Files Exceeding 4 GB Even if you shoot a movie exceeding 4 GB, you can keep shooting without interruption. Using CF cards up to 128 GB and SD/SDHC cards formatted with the camera If you use the camera to format a CF card with 128 GB or less in capacity or an SD/SDHC card, the camera will format it in FAT32. With a FAT32-formatted card, if you shoot a movie and the file size exceeds 4 GB, a new movie file will be created automatically.
3 Setting the Movie Recording Quality When downloading movie files exceeding 4GB to a computer, use either the EOS Utility (p.596) or a card reader (p.597). Movie files exceeding 4GB will not be downloaded if you perform image download with the function of a computer (OS). Deleting any of the movie files created as a movie shot at one time exceeding 4GB will make it impossible for EOS MOVIE Utility (p.599) to play back the movie files consecutively or to merge and save them as a single movie file.
3 Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or an external stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [z4: Sound recording] (the [z2] tab in mode). Sound Recording/Sound Recording Level Auto Manual Disable : The sound-recording level is adjusted automatically. Auto level control will operate automatically in response to the sound level. : For advanced users.
3 Setting the Sound Recording Wind Filter/Attenuator Wind filter Attenuator : When [Enable] is set, it reduces the wind noise when recording outdoors. This feature works only when you use the built-in microphone for movie shooting. Note that [Enable] reduces low bass sounds, so set it to [Disable] when there is no wind. It will record a more natural sound than with [Enable]. : Automatically suppresses sound distortion caused by loud noises. Even if [Sound rec.
3 Setting the Sound Recording If you use the Wi-Fi (wireless communication) function with an external microphone, the sound noise may be recorded. During sound recording, using the wireless communication function is not recommended. When connecting an external microphone or headphones to the camera, be sure to insert the plug all the way in. The camera’s built-in microphone will also record the operation sound and mechanical sound of the camera during shooting.
3 Setting the Time Code The time code is a time reference recorded automatically to synchronize the movie during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Use [z5: Time code] (the [z3] tab in mode) to set the time code. Count Up Rec run Free run : The time code counts up only while you are shooting a movie. The time code will continue in the sequence of the movie files captured.
3 Setting the Time Code Movie Recording Count You can select what to display on the movie shooting screen. Rec time Time code : Displays the elapsed time from the start of the movie shooting. : Displays the time code during movie shooting. Movie Playback Count You can select what to display on the movie playback screen. Rec time Time code : Displays the recording time and playback time during movie playback. : Displays the time code during movie playback.
3 Setting the Time Code HDMI Time code The time code can be appended to a movie that is output via HDMI. Enable: Appends time code to HDMI video output. When [Enable] is set, [Rec Command] will be displayed. Disable: Time code not appended to HDMI video output. Record command When a video output via HDMI is recorded by an external recording device, the camera’s movie shooting start and stop can sync with the recording by an external recording device.
3 Setting the Time Code Drop Frame If the frame rate is set to 2 (119.9 fps), 8(59.94 fps), or 6(29.97 fps), the time code’s frame count causes a discrepancy between the actual time and time code. When [Enable] is set, this discrepancy is corrected automatically. This correction function is called “drop frame.” This is for advanced users editing movies. Enable : The discrepancy is corrected automatically by skipping time code numbers (DF: Drop frame).
Shooting HDR Movies You can shoot movies with clipped highlights reduced for a high dynamic range of tones even in high-contrast scenes. You can set the HDR movie with the Quick Control screen if [Movie rec. size] is set to L6X (NTSC) or L5X (PAL) under [z4: Movie recording quality]. HDR movie shooting is possible either when the movie-recording format is set to MOV or MP4. 1 Check [Movie rec. size]. Check that [Movie rec. size] under [z4: Movie recording quality] is set to L6X or L5X.
Shooting HDR Movies For HDR movie shooting, the ISO speed auto and manual setting ranges are ISO 100 - ISO 25600. Expanded ISO speeds cannot be set. For the shutter speeds, see page 343. In the mode, the minimum ISO speed will be ISO 400. If [z3: Highlight tone priority] is set to [Enable], HDR movie shooting cannot be set. With HDR movie shooting, the image may still flicker even when an appropriate shutter speed has been set.
a Shooting Time-lapse Movies Still photos shot at a set interval can be stitched together automatically to create a time-lapse movie. A time-lapse movie shows how a subject changes in a much shorter period of time than the actual time it took. It is effective for a fixed-point observation of changing scenery, growing plants, celestial motion, etc. Time-lapse movies are recorded in MOV, L 6 W (NTSC) or L 5 W (PAL). The frame rate will be switched automatically according to the [53: Video system] setting (p.
a Shooting Time-lapse Movies the shooting interval and 5 Set number of shots. Time required Playback time Check the [k: Time required] and [3: Playback time] displayed at the bottom of the screen to set the shooting interval and number of shots. Select the number to be set (hours: minutes: seconds / number of shots). Press <0> so is displayed. Set the desired number, then press <0> (Returns to ). Shooting Interval Settable from [00:00:01] to [99:59:59].
a Shooting Time-lapse Movies Time required Indicates the time required to shoot the set number of shots with the set interval. If it exceeds 24 hours, “*** days” will be displayed. Playback time Indicates the movie recording time (time required to play back the movie) to create the time-lapse movie in L6W (NTSC) or L5W (PAL) from the still photos taken with the set intervals. Card- time left The total time available for recording time-lapse movies on the card based on its remaining capacity. the menu.
a Shooting Time-lapse Movies the <0> button. 11 Press X The camera will be ready to start shooting a time-lapse movie. To return to step 9, press the <0> button again. the time-lapse movie. 12 Shoot Press the shutter button halfway to Shots remaining Time-lapse movie 374 check the focus and exposure. Press the shutter button completely to start shooting the time-lapse movie. AF will not work during time-lapse movie shooting. The exposure setting for the first shot will be applied to subsequent shots.
a Shooting Time-lapse Movies Using a tripod is recommended. Taking test shots in advance is recommended. Regardless of the [z4: Movie recording quality] setting, the timelapse movie will be recorded in L 6 W (NTSC) or L 5 W (PAL). To cancel the time-lapse movie shooting before it is completed, either press the shutter button completely or press the <0> button ([Disable] is set). The time-lapse movie shot so far will be recorded on the card.
a Shooting Time-lapse Movies Do not point the camera toward an intense light source, such as the sun or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal components. With time-lapse movie set to [Enable], you cannot set [z4: Movie rec. quality], [53: Video system], or other settings. If the camera is connected to a computer with the interface cable, or if an HDMI cable is connected to the camera, you cannot select [Enable].
a Shooting Time-lapse Movies If the time it takes to record to the card exceeds the interval between shots due to the shooting functions set or card performance, some of the shots may not be taken with the set intervals. The captured images are not recorded as still photos. Even if you cancel the time-lapse movie shooting after only one shot is taken, it will be recorded as a movie file. If the card does not have enough free space to record the set number of shots, [Playback time] will be displayed in red.
a Shooting Time-lapse Movies You can shoot time-lapse movies with a fully-charged Battery Pack LP-E6N as shown in the table below (approx. time from start of shooting until the battery becomes exhausted). The possible shooting time will vary depending on the shooting conditions. Total Possible Time for Time-lapse Movie Shooting (Approx.) Room Temperature Low Temperatures Time-lapse Movie Shooting (23°C / 73°F) (0°C / 32°F) Shooting interval: 1 sec. 3 hr. 50 min. 3 hr. 40 min. Shooting interval: 10 sec.
3 Menu Function Settings z2 When the Live View shooting/Movie shooting switch is set to , the settings for [z2: ISO speed settings] will be switched to [ISO speed], [Range for movies], and [Range for H]. ISO Speed Settings ISO speed In the mode, you can set the ISO speed manually. You can also select ISO Auto. You can also use the button for these settings.
3 Menu Function Settings z4 When the Live View shooting/Movie shooting switch is set to , the [z4] and [z5] tabs will be displayed as the menu options exclusive to movie shooting (the [z2] and [z3] tabs in mode). Movie Servo AF With this function enabled, the camera focuses on the subject continuously during movie shooting. The default setting is [Enable]. When [Enable] is set: The camera focuses on the subject continuously even when you are not pressing the shutter button halfway.
3 Menu Function Settings Cautions When [Movie Servo AF] is Set to [Enable] Shooting Conditions that Make Focusing Difficult • A fast-moving subject approaching or moving away from the camera. • A subject moving at a close distance in front of the camera. • With a higher f/number • Also see “Shooting Conditions that Make Focusing Difficult” on page 324. Since this drives the lens continuously, it will consume battery power and shorten the movie shooting time (p.359).
3 Menu Function Settings AF method You can select [u+Tracking], [FlexiZone - Multi], or [FlexiZone Single]. See page 316 for the AF method. Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you compose with better balance by aligning the intersections over the subject. Note that the grid is not displayed during movie shooting.
3 Menu Function Settings Movie Servo AF SpeedN You can set the Movie Servo AF’s AF speed and its operation conditions. This function is settable when [Movie Servo AF] is set to [Enable] and [AF method] is set to [FlexiZone - Single]. Additionally, the function is enabled when using a lens supporting slow focus transition during movie shooting*. When active : [Always on] sets the AF adjustment speed to take effect at all times for movie shooting (before and during movie shooting).
3 Menu Function Settings Movie Servo AF tracking sensitivityN You can change the Movie Servo AF’s tracking sensitivity to one of seven levels. This affects the responsiveness of AF tracking sensitivity when the subject strays from the AF points, such as during panning or when an obstacle cuts across the AF points. This function is settable when [Movie Servo AF] is set to [Enable] and [AF method] is set to [FlexiZone - Single].
3 Menu Function Settings z5 Metering timerN You can change how long the exposure setting is displayed (AE lock time). Time code You can set the time code. For details, see page 365.
3 Menu Function Settings V button function You can set the functions performed by pressing the shutter button halfway or completely during movie shooting.
3 Menu Function Settings HDMI display This function enables you to select the display option while recording HDMI video output with an external recording device. The movie will be output in Full HD quality (1920x1080). The default setting is [a]. When [a] is set: • When outputting a movie via HDMI, the camera’s LCD monitor will be off. • The shooting information, AF points, etc., will be displayed on the HDMI video output.
3 Menu Function Settings How to prolong the HDMI output To continue the HDMI output for longer than 30 min., select [a] or [awithout info], then set [52: Auto Power Off] to [Disable] (p.76). HDMI output in 4K quality is not possible. (Even if [Movie rec. size] is set to H, the movie will be output in Full HD quality.) HDMI output with no information will not display the card’s remaining capacity, battery level, internal temperature warning (p.391), or other warnings on the HDMI output device’s screen.
3 Menu Function Settings Remote control shooting When [Enable] is set, you can start or stop movie shooting using Remote Controller RC-6 (sold separately, p.279). Set the RC-6’s release mode switch to <2>, then press the transmit button. If the switch is set to (immediate release), the [V btn function] setting will be applied.
3 Menu Function Settings 54 HDMI frame rate For HDMI output, you can set the frame rate to [Auto], [59.94i/ 50.00i], [59.94p/50.00p], or [23.98p]. Set the frame rate that is compatible with the commercially-available, external recording device you will use to record the movie via HDMI output. When [24.00p] under [z4: Movie rec quality] is set to [Enable], you cannot set [54: HDMI frame rate]. The movie will be output at 1080/ 24.00p via HDMI.
General Movie Shooting Cautions Red Internal Temperature Warning Icon If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a red icon will appear. The red icon indicates that movie shooting will soon be terminated automatically. If this happens, you will not be able to shoot again until the camera’s internal temperature decreases. Turn off the power and let the camera rest for a while.
General Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator Indicator becomes full, movie shooting will stop automatically.
10 Image Playback This chapter explains how to play back and erase the captured images (still photos/movies), how to view them on a TV screen, and other playback-related functions. Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. X The last image captured or played back will appear. an image. 2 Select To play back images starting with the last image captured, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the information display will change.
x Image Playback the image playback. 3 ExitPress the button to exit the image playback and return to shooting-ready state. If [84: Add cropping information] is set to an option other than [Off] (p.491), the captured images will show the lines indicating the image area when played back. Shooting Information Display With the shooting information screen displayed (p.394), you can tilt <9> up or down to switch the shooting information displayed at the screen bottom as follows.
x Image Playback 3 Grid Display In single-image display and two-image display (p.408), you can overlay the grid on the image playback. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag n]. This function is convenient for checking the image’s vertical or horizontal tilt as well as composition. The grid is not displayed during movie playback.
B: Shooting Information Display Sample Information for Still Photos Basic information display Eye-Fi transfer completed Wi-Fi function Wi-Fi signal strength/ Eye-Fi status Battery level Rating Protect images Cards Folder number File numbering Playback number/ Total images recorded Image-recording quality/Edited images/ Cropping/Frame Grab Shutter speed Aperture Exposure compensation amount Highlight tone priority ISO speed If the image was taken by another camera, certain shooting information may not
B: Shooting Information Display Shooting information display • Detailed information Exposure compensation amount Aperture Histogram (Brightness/RGB) Shooting date and time Shutter speed ISO speed Shooting mode/ Multiple exposures/ Frame Grab Highlight tone priority White balance Auto Lighting Optimizer White balance correction amount AF Microadjustment Scroll bar Metering mode File size Flash exposure compensation/ Bounce/HDR shooting/ Multi Shot Noise Reduction Image-recording quality/ Dual Pixel
B: Shooting Information Display • Lens / Histogram information Histogram display (Brightness) Lens name Histogram display (RGB) Focal length • White balance information • Picture Style information 1 • Picture Style information 2 Frame-grab images from 4K movies saved as still photos (p.427) will not display certain shooting information screens.
B: Shooting Information Display • Color space / Noise reduction information • Lens aberration correction information 1 • Lens aberration correction information 2 • GPS information • IPTC information Latitude Longitude Elevation UTC (Coordinated Universal Time) If the GPS information is not recorded or the IPTC information is not appended to the image, the GPS information screen or IPTC information screen will not be displayed.
B: Shooting Information Display Sample Movie Information Display Movie playback Aperture Shutter speed ISO speed Movie shooting mode/ High Frame Rate movie Movie-recording format Movie recording size Frame rate • • • • : Shutter speed, aperture, and ISO speed are not displayed. >: Aperture and ISO speed are not displayed. >: Shutter speed and ISO speed are not displayed.
B: Shooting Information Display AF Point Display When [33: AF point disp.] is set to [Enable], the AF point that achieved focus will be displayed in red. If automatic AF point selection is set, multiple AF points may be displayed. Histogram The brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram is for checking the color saturation and gradation. The display can be switched with [33: Histogram disp].
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing 4, 9, 36, or 100 images on one screen. 1 Press the button. During image playback or when the camera is ready to shoot, press the button. X [6u] will be displayed on the lower right of the screen. to the index display. 2 Switch Turn the <6> dial counterclockwise. X The 4-image index display will appear.
x Searching for Images Quickly I Jumping through Images (Jump Display) In the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. 1 Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>. the jump method. 2 Select Select the jump method, then press <0>.
x Searching for Images Quickly by jumping. 3 Browse Press the button to play back Jump method images. In the single-image display, turn the <6> dial. X You can browse by the method that was set. Playback position To search images by shooting date, select [Date]. To search images by folder, select [Folder]. If the card contains both movies and still photos, select [Movies] or [Stills] to display one or the other.
u Magnifying Images You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. 1 Magnified area position Magnify the image. The image can be magnified as follows: 1. During image playback (single-image display), 2. During the image review after image capture, and 3. From the shooting-ready state. Press the button. X The magnified view will appear. The magnified area and [6u] will be displayed on the lower right of the screen.
u Magnifying Images 3 Setting the Initial Magnification Ratio and Position Under the [33] tab, when you select [Magnificatn (apx)], you can set the initial magnification ratio and position for the magnified view. 1x (no magnification) The image is not magnified. The magnified view will start with the single-image display. 2x, 4x, 8x, 10x (magnify from center) The magnified view starts at the image center at the selected magnification.
X Comparing Images (Two-Image Display) You can compare two images side by side on the LCD monitor. In the two-image display, you can use magnified view or jump display as well as protection, rating and erasure of images. 1 Set the two-image display. During image playback, press the button. X The two-image index display will appear. The selected image is highlighted with an orange frame. the images to be 2 Select compared. Pressing <0> switches the orange frame between the two images.
d Playing Back with the Touch Screen The LCD monitor is a touch-sensitive panel that you can touch with your fingers for various playback operations. First, press the button to play back images. Browsing Images Swipe with one finger. With single-image display, touch the LCD monitor with one finger. You can browse to the next or previous image by swiping your finger to the left or right. Swipe to the left to see the next (newer) image, or swipe to the right to see the previous (older) image.
d Playing Back with the Touch Screen Reducing Image (Index Display) Pinch two fingers. Touch the screen with two fingers spread apart, and pinch your fingers together on the screen. Each time you pinch your fingers, the image will shrink. If you pinch the single-image display, it will change to the 4-image index display. When you select an image, the orange frame will appear. Tap on the image again to display it as a single image. Magnifying Image Spread two fingers apart.
b Rotating the Image You can rotate the displayed image to the desired orientation. 1 Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. the image to be rotated. 2 Select Turn the <5> dial to select the image to be rotated. You can also select an image in the index display (p.403). the image. 3 Rotate Each time you press <0>, the image will rotate clockwise as follows: 90° 9 270° 9 0°. To rotate another image, repeat steps 2 and 3.
K Protecting Images You can protect important images from being accidentally erased by the camera’s erase function. 3 Protecting a Single Image 1 Select [Protect images]. Under the [31] tab, select [Protect images], then press <0>. [Select images]. 2 Select X An image is displayed. Image protection icon the image to be protected. 3 Select Turn the <5> dial to select the image to be protected. You can also select an image on the index display (p.403). the image.
K Protecting Images 3 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at once. When you select [All images in folder] or [All images on card] in [31: Protect images], all the images in the folder or on the card will be protected. To cancel the image protection, select [Unprotect all images in folder] or [Unprotect all images on card]. If you format the card (p.73), the protected images will also be erased. Movies can also be protected.
K Protecting Images Protecting Images with the Button During image playback, you can use the button to protect an image. 1 Select [m btn function]. Under the [53] tab, select [m btn function], then press <0>. 2 Select [Protect]. the image to be protected. 3 Select Press the button to play back images. Turn the <5> dial to select the image to be protected. You can also select an image on the index display (p.403). the image.
Setting Ratings You can rate images (still photos and movies) with one of the five rating marks: l/m/n/o/p. This function is called rating. Rating Images with the Button 1 Select the image to be rated. Press the button to play back images. Turn the <5> dial to select the image to be rated. You can also select an image on the index display (p.403). 2 RateEachthetimeimage. you press the button, the rating mark will change: l/m/n/o/p/None. To rate another image, repeat steps 1 and 2.
Setting Ratings 3 Set Ratings with the Menu 1 Select [Rating]. Under the [32] tab, select [Rating], then press <0>. the image to be rated. 2 Select Turn the <5> dial to select the image to be rated. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the dial clockwise. the image. 3 RatePress <0>, and a blue highlight frame will appear as shown in the screenshot.
Setting Ratings Taking Advantage of Ratings With [32: Image jump w/6], you can display only the images having a specific rating. With [32: Slide show], you can play back only the images having a specific rating. Depending on the computer’s OS, you can see each file’s rating as part of the file information display or in the provided, standard image viewer (JPEG images only).
Q Quick Control for Playback During playback, you can press the button to set the following: [J: Protect images], [b: Rotate image], [9: Rating], [R: RAW image processing (1 images only)], [S: Resize (JPEG image only)], [N: Cropping (JPEG images only)], [ : Highlight alert], [ : AF point display], [e: Image jump w/6], and [q: Send images to smartphone*]. For movies, only the functions in bold above can be set.
Q Quick Control for Playback To rotate an image, set [51: Auto rotate] to [OnzD] (p.444). If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the button during the index display will switch to the single-image display, and the Quick Control screen will appear. Pressing the button again will return to the index display.
k Enjoying Movies The three main ways to play back and enjoy movies are as follows: Playback on a TV Set (p.432) By connecting the camera to a TV set with HDMI Cable HTC-100 (sold separately), you can play back the camera’s still photos and movies on the TV set. When the camera is connected to a TV set with an HDMI cable, even 4K movies will be played back in Full HD quality (they cannot be played back in 4K quality).
k Enjoying Movies Playback and Editing with a Computer The movie files recorded on the card can be transferred to a computer and played back or edited with pre-installed or general-purpose software compatible with the movie’s recording format. To play back or edit a movie with commercially-available software, use software compatible with MOV-format and MP4-format movies. For details on commercially-available software, contact the software manufacturer.
k Playing Back Movies 1 Play back the image. Press the button to play back images. a movie. 2 Select Turn the <5> dial to select the movie to be played back. In the single-image display, the icon displayed on the upper left indicates a movie. In the index display, perforations at the left edge of a thumbnail indicate a movie. As movies cannot be played back from the index display, press <0> to switch to the single-image display. the single-image display, press 3 In<0>.
k Playing Back Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjusts the slow motion speed by turning the <5> dial. The slow motion speed is indicated on the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Displays the previous frame each time you press <0>. Holding down <0> will rewind the movie. 6 Next frame Plays the movie frame-by-frame each time you press <0>.
k Playing Back Movies Playback with the Touch Screen Tap [7] at the center of the screen. X The movie will start playing back. To display the movie playback panel, tap on the upper left of the screen. To pause the movie while it is playing back, tap on the screen. The movie playback panel will also appear. Playing High Frame Rate Movies HD movies shot at a high frame rate (119.9 fps or 100.0 fps) will be played back at 1/4-speed slow motion (29.97 fps or 25.00 fps).
X Editing a Movie’s First and Last Scenes You can edit out the first and last scenes of a movie in approx. 1-sec. increments. 1 On the movie playback screen, select [X]. X The movie editing panel will be displayed at the bottom of the screen. the part to be edited out. 2 Specify Select either [U] (Cut beginning) or [V] (Cut end), then press <0>. Tilt <9> to the left or right to see the previous or next frames. Holding down the key will fast forward or fast rewind the frames.
X Editing a Movie’s First and Last Scenes the edited movie. 4 Save Select [W], then press <0>. X The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite], then press <0>. On the confirmation dialog, select [OK] to save the edited movie and return to the movie playback screen. X Since the editing is performed in approx. 1-sec.
Grabbing a Frame from 4K Movies From a 4K movie, you can select any desired frame to save it as an approx. 8.8 megapixel (4096x2160) still photo (JPEG image). This function is called “Frame Grab (4K frame capture)”. 1 Play back the image. Press the <3> button to play back images. a 4K movie. 2 Select Turn the <5> dial and select a 4K quality movie. On the shooting information screen (p.401), the 4K movie is indicated with the [H] icon.
Grabbing a Frame from 4K Movies the frame. 6 Save Select [OK] to save the frame displayed on the screen as a still photo (JPEG image). Check the destination folder and image file number. the image to be displayed. 7 Select Select [View original movie] or [View extracted still image]. X The selected image will be displayed. Frame grabbing is not possible with Full HD movies or 4K movies shot with a different camera. Frame grabbing is not possible if the camera is connected to a computer.
3 Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. 1 Number of images to be played back Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. the images to be played 2 Select back. Select the desired option on the screen, then press <0>. All images/Movies/Stills/Protect Turn the <5> dial to select one of the following: [jAll images] [kMovies] [zStills] [JProtect]. Then press <0>.
3 Slide Show (Auto Playback) Item Playback Description jAll images All the still photos and movies on the card will be played back. iDate Still photos and movies taken on the selected shooting date will be played back. nFolder Still photos and movies in the selected folder will be played back. kMovies Only the movies on the card will be played back. zStills Only the still photos on the card will be played back.
3 Slide Show (Auto Playback) the slide show. 4 StartSelect [Start], then press <0>. X After [Loading image...] is displayed, the slide show will start. slide show. 5 ExitTothe exit the slide show and return to the setting screen, press the button. To pause the slide show, press <0>. During pause, [G] will be displayed on the upper left of the image. Press <0> again to resume the slide show. During the automatic playback of still images, you can press the button to switch the display format (p.
Viewing Images on a TV Set By connecting the camera to a TV set with an HDMI cable (sold separately), you can play back the camera’s still photos and movies on the TV set. For the HDMI cable, HDMI Cable HTC-100 (sold separately) is recommended. If the picture does not appear on the TV screen, check if the [53: Video system] is correctly set to [For NTSC] or [For PAL] (depending on the video system of your TV set). 1 Connect the HDMI cable to the camera.
Viewing Images on a TV Set When the camera is connected to a TV set with an HDMI cable, even 4K movies will be played back in Full HD quality (they cannot be played back in 4K quality). Adjust movie sound volume with the TV set. The sound volume cannot be adjusted with the camera. Before connecting or disconnecting the cable between the camera and TV set, turn off the camera and TV set. Depending on the TV set, part of the image displayed may be cut off.
Viewing Images on a TV Set the camera’s button. 4 Press X An image will appear on the TV screen and you can use the TV set’s remote control for playback. an image. 5 Select Point the remote control toward the TV set and press the / button to select an image. the remote control’s Enter 6 Press button.
a Copying Images You can copy the images recorded on one card (save duplicates) to the other card. Movie Files Exceeding 4 GB If you are copying images between cards and the copy target card is formatted in FAT32 (p.74), movie files exceeding 4 GB recorded on the exFAT-formatted copy source card cannot be copied. Movie files exceeding 4 GB can be copied between cards when both Card1 (f) and Card2 (g) are formatted in exFAT. 3 Copying a Single Image 1 Select [Image copy].
a Copying Images Lowest file number Number of images in folder the folder. 3 Select Select the folder containing the image you want to copy, then press <0>. Check the images displayed on the right to select the desired folder. X The images in the selected folder will be displayed. Folder name Highest file number Total images selected the images to be copied. 4 Select Turn the <5> dial to select an image to be copied, then press <0>. X The [X] icon will appear on the upper left of the screen.
a Copying Images the target folder. 7 Select Select the target folder to which you want to copy the images, then press <0>. To create a new folder, select [Create folder]. [OK]. 8 Select Check the information of the source card and target card, then select [OK]. X The copying will start and the progress will be displayed. When the copying is completed, the result will be displayed. Select [OK] to return to the screen in step 2.
a Copying Images If an image is being copied to a target folder/card which has an image with the same file number, the following will be displayed: [Skip image and continue] [Replace existing image] [Cancel copy]. Select the copying method, then press <0>. • [Skip image and continue]: Any images having the same file number will be skipped and not copied. • [Replace existing image]: Any images having the same file number (including protected images) will be overwritten. If an image with a print order (p.
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images (p.412) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Select the image to be erased. Press the button to play back images.
L Erasing Images 3 Checkmarking [X] Images to Be Erased in a Batch By adding checkmarks to the images to be erased, you can erase multiple images at once. 1 Select [Erase images]. Under the [31] tab, select [Erase images], then press <0>. [Select and erase images]. 2 Select X An image is displayed. the images to be erased. 3 Select Turn the <5> dial to select the image to be erased, then press <0>. X A checkmark [X] will be displayed on the upper left of the screen.
L Erasing Images 3 Erasing All Images in a Folder or on a Card You can erase all the images in a folder or on a card at once. When [31: Erase images] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be erased. To erase all images including protected images, format the card (p.73). When [All images on card] is selected, the images in the card selected under [51: Record func+card/folder sel.] with [Record/play] or [Playback] will be erased.
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness The LCD monitor’s brightness is adjusted automatically for optimum viewing depending on the ambient light level. You can also set the brightness level of automatic adjustment (brighter or darker), or adjust the brightness manually. 1 Select [LCD brightness]. Under the [52] tab, select [LCD brightness], then press <0>. [Auto] or [Manual]. 2 Select Turn the <6> dial to make the selection. the brightness.
Changing Image Playback Settings 3 Setting the LCD Monitor Color Tone You can change the LCD monitor’s color tone from standard tone to warm or cool tone. 1 Select [LCD color tone]. Under the [52] tab, select [LCD color tone], then press <0>. the desired color tone. 2 Select While looking at the image on the LCD monitor, select an option (1, 2, 3, or 4), then press <0>. You can select [1: Warm tone], [2: Standard], [3: Cool tone 1], or [4: Cool tone 2].
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Images shot in vertical orientation are rotated automatically to the proper orientation for viewing, so they will not be displayed in horizontal orientation when played back on the camera’s LCD monitor or viewed on a computer screen. You can change the setting of this feature. 1 Select [Auto rotate]. Under the [51] tab, select [Auto rotate], then press <0>. the display orientation. 2 SetSelect the desired setting, then press <0>.
11 Post-Processing Images This chapter explains RAW image processing, JPEG image resizing, and JPEG image cropping. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . The camera may not be able to process images taken with another camera. Post-processing images as described in this chapter cannot be performed when the camera is connected to a computer via an interface cable.
R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. As the RAW image itself does not change, you can apply different processing conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera. Use Digital Photo Professional (EOS software, p.598) to process those images. 1 Select [RAW image processing]. Under the [31] tab, select [RAW image processing], then press <0>.
R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the selected function’s setting screen. Turn the <5> or <6> dial to change the setting. Press <0> to finalize the setting and return to the previous screen. the image. 4 Save Select [W] (Save), then press <0>. When you select [OK], the JPEG image created by processing will be saved to the card. Check the destination folder and image file number, then select [OK]. To process another image, repeat steps 2 to 4.
R Processing RAW Images with the CameraN Magnified View You can magnify the image by pressing the button in step 3. The magnification will differ depending on the [Image quality] setting under [x1: RAW image processing]. With <9>, you can scroll around the magnified image. To cancel the magnified view, press the button again. Images with Aspect Ratio Setting With [z5: Aspect ratio] (p.
R Processing RAW Images with the CameraN RAW Image Processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance (p.192) You can select the white balance. If you select [Q] and press the button, you can select [Auto: Ambience priority] or [Auto: White priority]. If you select [P] and press the button, you can set the color temperature.
R Processing RAW Images with the CameraN Color space (p.217) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the difference in the image will hardly be perceptible when either color space is set. Lens aberration correction • Peripheral illumination correction (p.207) A phenomenon that makes the image corners look darker due to the lens characteristics can be corrected. If [Enable] is set, the corrected image will be displayed.
R Processing RAW Images with the CameraN • Chromatic aberration correction (p.211) Chromatic aberrations (color fringing along the subject’s outline) due to the lens characteristics can be corrected. If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, magnify the image (p.448). • Diffraction correction (p.212) The diffraction by the lens aperture degrading the image sharpness can be corrected. If [Enable] is set, the corrected image will be displayed.
S Resizing JPEG Images You can resize a JPEG image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3, 4, a, and b images. JPEG c images, RAW images, and frame-grab images from 4K movies saved as still photos cannot be resized. 1 Select [Resize]. Under the [32] tab, select [Resize], then press <0>. X An image is displayed. the images to be resized. 2 Select Turn the <5> dial to select the image you want to resize.
S Resizing JPEG Images Resize Options by Original Image Quality Available Resize Settings Original Image Quality 4 a b c 3 k k k k k k k k k 4 a k b Image Sizes Sizes for resized images are shown below. (Approx.) Image Quality Full-frame (3:2) 4:3 (aspect ratio) 4 4464x2976 (13.3 megapixels) 3968x2976 (11.8 megapixels) a 3360x2240 (7.5 megapixels) *2976x2240 (6.7 megapixels) b 1920x1280 (2.5 megapixels) *1696x1280 (2.
N Cropping JPEG Images You can crop a captured JPEG image and save it as another image. Cropping an image is possible only with JPEG 3, 4, a, and b images. Images shot in JPEG c or RAW, and frame-grab images from 4K movies saved as still photos cannot be cropped. 1 Select [Cropping]. Under the [x2] tab, select [Cropping], then press <0>. X An image is displayed. an image. 2 Select Turn the <5> dial to select the image you want to crop.
N Cropping JPEG Images Moving the Cropping Frame Use <9> to move the frame over the image vertically or horizontally. Move the cropping frame until it covers the desired image area. Switching the Cropping Frame Orientation Pressing the button will toggle the cropping frame between the vertical and horizontal orientations. This enables you to crop the image shot in horizontal orientation to look as if it was shot in vertical orientation. the image area to be 4 Check cropped. Press the button.
MEMO 456
12 Sensor Cleaning The camera has a Self Cleaning Sensor Unit to automatically shake off dust adhered to the image sensor’s front layer (low-pass filter). The Dust Delete Data can also be appended to the image so that the dust spots remaining can be deleted automatically by Digital Photo Professional (EOS software, p.598).
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit is activated to automatically shake off any dust on the front of the sensor. Normally, you need not pay attention to this operation. However, you can manually perform sensor cleaning or can disable this unit as follows. Activating the Sensor Cleaning Manually 1 Select [Sensor cleaning]. Under the [53] tab, select [Sensor cleaning], then press <0>. [Clean nowf].
f Automatic Sensor Cleaning For best results, perform the sensor cleaning with the camera placed upright and stable on a table or other flat surface. Even if you repeat the sensor cleaning, the result will not improve much. Immediately after the sensor cleaning is finished, the [Clean nowf] option remains disabled temporarily. Dots of light may appear on images if the sensor is affected by cosmic rays, etc. By selecting [Clean nowf], their appearance may be suppressed (p.571).
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, for the case where visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later. The Dust Delete Data is used by Digital Photo Professional (EOS software, p.598) to erase the dust spots automatically. Preparation Prepare a solid white object such as a sheet of paper.
3 Appending Dust Delete DataN a solid-white object. 3 Shoot At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in aperturepriority AE mode at an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no card in the camera. X When the picture is taken, the camera will start collecting the Dust Delete Data.
3 Appending Dust Delete DataN Dust Delete Data After the Dust Delete Data is obtained, it is appended to all the JPEG and RAW images captured thereafter. Before an important shoot, it is recommended that you update the Dust Delete Data by obtaining it again. For details about using Digital Photo Professional (EOS software, p.598) to erase dust spots, refer to the Digital Photo Professional Instruction Manual (p.600).
3 Manual Sensor CleaningN Dust that could not be removed by the automatic sensor cleaning can be removed manually with a commercially-available blower, etc. Before cleaning the sensor, detach the lens from the camera. The image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. 1 Select [Sensor cleaning]. Under the [53] tab, select [Sensor cleaning], then press <0>. 2 Select [Clean manually]. [OK].
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. If the power is cut off, the shutter will close and the reflex mirror will go back down. These may result in damaging the image sensor, shutter curtains, and reflex mirror. • Setting the power switch to <2>. • Removing or inserting the battery. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor.
13 Transferring Images to a Computer and Print Ordering Transferring Images to a Computer (p.466) You can connect the camera to a computer and operate the camera alone to transfer images recorded on the card to the computer. Digital Print Order Format (DPOF) (p.471) DPOF (Digital Print Order Format) enables you to print images recorded on the card according to your printing instructions such as the image selection, quantity to print, etc.
d Transferring Images to a Computer You can connect the camera to a computer and operate the camera to transfer images on the card to the computer. This is called direct image transfer. You can perform the direct image transfer with the camera while looking at the LCD monitor. The images transferred to the computer will be saved in the [Pictures] or [My Pictures] folder and organized in folders by shooting date. Before connecting the camera to a computer, install EOS Utility (EOS software, p.
d Transferring Images to a Computer the power switch to <1>. 3 SetWhen the computer displays a screen to select the program, select [EOS Utility]. X The EOS Utility screen will appear on the computer. After the EOS Utility screen appears, do not operate EOS Utility. If any screen other than EOS Utility’s main window is displayed, [Direct transfer] in step 5 on page 469 will not be displayed. (You cannot transfer images to the computer.
d Transferring Images to a Computer 3 Selecting the Images to be Transferred Selecting Images 1 Select [Image transfer]. Under the [32] tab, select [Image transfer], then press <0>. 2 Select [Image sel./transfer]. 3 Select [Sel.Image]. the images to be transferred. 4 Select Turn the <5> dial to select the image to be transferred, then press <0>. Turn the <5> dial to display the [X] on the upper left of the screen, then press <0>.
d Transferring Images to a Computer the image. 5 Transfer On the computer screen, check that EOS Utility’s main window is displayed. Select [Direct transfer], then press <0>. On the confirmation dialog, select [OK] to transfer the images to the computer. Images selected with [Sel.n] and [All images] can also be transferred in this way. Selecting n Select [Sel.n] and select [Folder images not transfer’d].
d Transferring Images to a Computer All images If [All images] is selected and you select [Card images not transferred], all the images on the card not yet transferred to a computer will be selected. For a description of [Card images failed transfer] and [Clear card’s transf. history], see “Selecting n” on the preceding page. If any screen other than EOS Utility’s main window is displayed on the computer, [Direct transfer] is not displayed. During the image transfer, certain menu options cannot be used.
W Digital Print Order Format (DPOF) DPOF (Digital Print Order Format) enables you to print images recorded on the card according to your printing instructions such as the image selection, quantity to print, etc. You can print multiple images in one batch or create a print order for a photofinisher. You can set the print settings such as print type, date imprinting, file number imprinting, etc. The print settings will be applied to all printordered images. (They cannot be set individually for each image.
W Digital Print Order Format (DPOF) Print type Date File number K Standard Prints one image on one sheet. L Index Multiple thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date of the captured image. [On] imprints the file number. 4 Exit the setting. Press the button. X The print order screen will reappear. Next, select [Sel.Image], [Byn], or [All images] to order the images to be printed.
W Digital Print Order Format (DPOF) RAW images and movies cannot be print ordered. If you print an image with a large image size using the [Index] or [Both] setting (p.471), the index print may not be printed with certain printers. In such a case, resize the image (p.452), then print the index print. Even if [Date] and [File No.] are set to [On], the date or file number may not be imprinted, depending on the print type setting and printer. With [Index] prints, the [Date] and [File No.
W Digital Print Order Format (DPOF) Specifying Images for Printing Selecting Images Select and order images one by one. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6> dial clockwise. Press the button to save the print order to the card. Standard / Both Quantity Total images selected Press <0> to print a copy of the displayed image.
W Digital Print Order Format (DPOF) All images If you select [Mark all on card], one copy of all the images on the card will be set for printing. If you select [Clear all on card], the print order will be cleared for all the images on the card. Note that RAW images and movies will not be included in the print order even if you set [Byn] or [All images]. When using a PictBridge-compatible printer (Wireless LAN), do not specify more than 400 images for one print order.
p Specifying Images for a Photobook You can specify up to 998 images to be printed in a photobook. When you use EOS Utility (EOS software) to transfer images to a computer, the specified images will be copied to a dedicated folder. This function is useful for ordering photobooks online. Specifying One Image at a Time 1 Select [Photobook Set-up]. Under the [x1] tab, select [Photobook Set-up], then press <0>. 2 Select [Select images]. the image to be specified.
p Specifying Images for a Photobook Specifying All Images in a Folder or on a Card You can specify all the images in a folder or on a card at once. When [x1: Photobook Set-up] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be specified. To clear your selections, select [Clear all in folder] or [Clear all on card]. RAW images and movies cannot be specified.
MEMO 478
14 Customizing the Camera You can make fine adjustments to various camera functions and change the functionality of buttons and dials to suit your picture-taking preferences with Custom Functions and Custom Controls. You can also save the camera’s current settings to the , , and modes. Note that the features explained in this chapter can be set and work in the following shooting modes: , , , , and .
3 Custom FunctionsN 81: Exposure Exposure level increments ISO speed setting increments Bracketing auto cancel Bracketing sequence A LV Shooting p.482 p.483 k Movie Shooting k k k In a k k Number of bracketed shots p.484 k Safety shift p.485 k Same exposure for new aperture p.486 k 82: Exposure Set shutter speed range Set aperture range p.488 k k k k Shaded Custom Functions do not function during Live View (LV) shooting or movie shooting. (Settings are disabled.
3 Custom FunctionsN A LV Shooting 83: Display/Operation Warnings z in viewfinder p.489 LV shooting area display Dial direction during Tv/Av k Movie Shooting k p.490 Custom Controls k k Depends on setting 84: Others Add cropping information Default Erase option Retract lens on power off Add IPTC information p.491 p.492 p.493 k (During playback) k k k 85: Clear Selecting [85: Clear all Custom Func. (C.Fn)] will clear all the Custom Function settings. Even if [85: Clear all Custom Func.(C.
3 Custom Function SettingsN Under the [8] tab, you can customize various camera features to suit your picture-taking preferences. Any settings different from the default will be displayed in blue. C.Fn1: Exposure Exposure level increments C.Fn1 1/3:1/3-stop 1/2:1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. When [1/2-stop] is set, the exposure level will be displayed as shown below. ISO speed setting increments C.
3 Custom Function SettingsN Bracketing auto cancel C.Fn1 ON: Enable When you set the power switch to <2>, the AEB and white balance bracketing settings will be canceled. AEB settings will also be canceled when the flash is ready to fire or if you switch to movie shooting. OFF: Disable The AEB and white balance bracketing settings will not be canceled even if you set the power switch to <2>.
3 Custom Function SettingsN Number of bracketed shots C.Fn1 The number of shots taken with AEB and white balance bracketing can be changed from the default 3 shots, to 2, 5, or 7 shots. When [81: Bracketing sequence] is set to [0, -, +], the bracketed shots will be taken as shown in the table below.
3 Custom Function SettingsN Safety shift C.Fn1 OFF: Disable Tv/Av: Shutter speed/Aperture Takes effect in the shutter-priority AE and aperturepriority AE modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain the standard exposure. ISO: ISO speed Works in the Program AE, shutter-priority AE, and aperture-priority AE modes.
3 Custom Function SettingsN Same exposure for new aperture C.Fn1 If the mode (manual exposure shooting) is set and the ISO speed is set manually (except when set to ISO Auto), the open aperture value may change to a higher number (a smaller aperture) if you perform any of the following: 1. Change the lens, 2. Attach an extender, or 3. Use a zoom lens whose open aperture value (f/number) changes.
3 Custom Function SettingsN Tv: Shutter speed If you perform 1, 2, or 3, a slower shutter speed will automatically be set to compensate for the number of stops the maximum aperture has become slower. The same exposure that would be obtained without performing 1, 2, or 3 is thereby obtained. The shutter speed will change automatically within the range set with [82: Set shutter speed range].
3 Custom Function SettingsN C.Fn2: Exposure Set shutter speed range C.Fn2 You can set the shutter speed range. In the and modes, you can set the shutter speed manually within the range you have set. In the and modes, the shutter speed will be set automatically within the set shutter speed range (except for movie shooting). Then select [OK] to register the setting. Highest speed You can set it from 1/8000 sec. to 15 sec. Lowest speed You can set it from 30 sec. to 1/4000 sec.
3 Custom Function SettingsN C.Fn3: Disp./Operation Warnings z in viewfinder C.Fn3 When any of the following functions are set, the icon can be displayed in the viewfinder and on the LCD panel (p.31). Select the function for which you want the warning icon to appear, then press <0> to add a checkmark [X]. Then select [OK] to register the setting. When monochrome V is set If the Picture Style is set to [Monochrome] (p.185), the warning icon will appear.
3 Custom Function SettingsN Live View shooting area display C.Fn3 When the aspect ratio (p.310) for Live View shooting is set to [4:3], [16:9], or [1:1], you can set the display method for the image area. : Masked : Outlined Dial direction during Tv/Av C.Fn3 : Normal : Reverse direction Dial turning direction when setting the shutter speed and aperture can be reversed. In the shooting mode, the turning direction of the <6> and <5> dials will be reversed.
3 Custom Function SettingsN C.Fn4: Others Add cropping information C.Fn4 If you set the cropping information, vertical lines for the aspect ratio you set during the Live View shooting will be displayed on the screen. You can then compose the shot as if you were shooting with a medium- or large-format camera (6x6 cm, 4x5 inch, etc.). When you take a picture, the aspect ratio information for cropping the image with the Digital Photo Professional (EOS software, p.598) will be appended to the image.
3 Custom Function SettingsN Default Erase option C.Fn4 During image playback and image review immediately after shooting, when you press the button, the erase menu appears (p.439). You can set which option, [Cancel] or [Erase], is to be preselected on this screen. If [Erase] is set, you can just press <0> to quickly erase the image. : [Cancel] selected L : [Erase] selected If [Erase] is set, be careful not to erase an image accidentally. Retract lens on power off C.
3 Custom Function SettingsN Add IPTC information C.Fn4 With the IPTC (International Press Telecommunications Council) information from EOS Utility (EOS software, p.598) registered to the camera, the IPTC information can be recorded (appended) to the still photos (JPEG/RAW images) you shoot. Useful for file management and other tasks utilizing the IPTC information.
MEMO 494
7 Custom ControlsN You can assign often-used functions to camera buttons or dials for ease of operation according to your preferences. 1 Select [Custom Controls]. Under the [83] tab, select [Custom Controls], then press <0>. X The Custom Controls setting screen will appear. a camera button or dial. 2 Select Select a camera button or dial, then press <0>. X The name of the camera control and the assignable functions will be displayed.
7 Custom ControlsN Assignable Functions to Camera Controls Function Page Metering and AF start 500 AF stop 501 Switch to registered AF function 502 ONE SHOT z AI SERVO/SERVO AF k k*1 k*1 k k k*3 k*3 k k Switch to registered AF point Selected AF point z Center/Registered AF point 503 Direct AF point selection Direct AF area selection 504 Pause Movie Servo AF k Metering start 504 AE lock k Exposure AE lock (while button pressed) AE lock (hold) k k AE lock, AF stop k k k k FE
7 Custom ControlsN p k k k k*2 k*2 3 k* k*3 k*4 k*4 k*5 k*6 k*7 k k k k k k k k k k k k k k k k k k k k k k < > stands for “AF stop button” provided on super telephoto lenses equipped with Image Stabilizer.
7 Custom ControlsN Function Page Images One-touch image quality setting One-touch image quality (hold) 507 Image quality Picture Style 508 Depth-of-field preview IS start 508 Menu display Operation Register/recall shooting function k*9 k*9 k k Unlock while button pressed Start movie recording (when k set) Image replay Magnify/Reduce (press SET, turn ) 509 Cycle: y•g/o/n Flash function settings No function (disabled) 498
7 Custom ControlsN p k*8 k*8 k*8 k*8 k k k k k k k k k k k k k k k k k k k k k k < > stands for “AF stop button” provided on super telephoto lenses equipped with Image Stabilizer.
7 Custom ControlsN AF : Metering and AF start When you press the button assigned to this function, metering and AF are performed. *1: When assigned to the
or button, pressing the button while the setting screen is displayed will enable you to set the detailed AF settings. When shooting, pressing the or button will perform AF as it was set. AF start position When [Registered AF point] is set, you can press the or button to switch to the registered AF point.
7 Custom ControlsN AI Servo AF characteristics (p.127) Press the
or button to perform AF with the set case from [Case 1] to [Case 6]. AF operation (p.100) Press the or button to perform AF with the set AF operation. AF area selection mode (p.104) Press the or button to perform AF with the set AF area selection mode. If you want to keep using the currently selected AF point when you press the or button, set [AF start position] to [Manually selected AF point].
7 Custom ControlsN : Switch to registered AF function Only while you hold down the depth-of-field preview button or the lens’s AF stop button, you can apply AF with the following settings: AF area selection mode (p.104), Tracking sensitivity (p.132), Acceleration/ deceleration tracking (p.133), AF point auto switching (p.134), Servo 1st image priority (p.136), and Servo 2nd image priority (p.137). Useful when you want to change the AF characteristics during AI Servo AF.
7 Custom ControlsN : Switch to registered AF point While the metering timer is active, when you press the depth-of-field preview button or the lens’s AF stop button, the focusing point can be switched to the registered AF point. *4: On the setting screen, when you press the button, you can select [Switch only when btn is held] or [Switch each time btn is pressed]. To register the AF point, see page 500.
7 Custom ControlsN : Direct AF area selection If the metering timer is active, you can press the
(AF area selection) button to directly select an AF area selection mode without pressing the button. : Pause Movie Servo AF When Movie Servo AF is active, you can pause the AF by pressing the Depth-of-field preview button or <0>. Press the button again to resume Movie Servo AF. Exposure : Metering start When you press the shutter button halfway, exposure metering is performed (AF is not performed).
7 Custom ControlsN : AE lock (hold) When you press the button assigned to this function, you can lock the exposure (AE lock). The AE lock will be maintained until you press the button again. Useful when you want to set the focus and meter separately or take multiple shots at the same exposure setting. : AE lock, AF stop When you press the button assigned to this function, you can lock the exposure (AE lock) and the AF will stop.
7 Custom ControlsN : Set ISO speed ( during metering) While the metering timer is active, you can set the ISO speed by turning the <5> dial. If this control is used with ISO Auto set, you can set the ISO speed manually. (Even after the metering timer (0) ends, ISO Auto will not be restored.) If you use this function in the mode, you can adjust the exposure with the ISO speed while maintaining the current shutter speed and aperture value.
7 Custom ControlsN Images : One-touch image quality setting Pressing the depth-of-field preview button or button will switch to enable shooting with the image-recording quality set here. If [Show/hide in viewfinder] has [Image quality] checkmarked [X] (p.84), the imagerecording quality (JPEG or RAW image type) will blink in the viewfinder. After the shooting ends, the One-touch image quality setting will be canceled and the image-recording quality will be switched back to the previous quality.
7 Custom ControlsN : Picture Style Press <0> to display the Picture Style selection setting screen on the LCD monitor (p.183). Operation : Depth-of-field preview When you press the depth-of-field preview button or <0>, the aperture will stop down and you can check the depth of field (p.250). : IS start If you press the depth-of-field preview button or the lens’s AF stop button with the lens’s IS switch set to <1>, the lens’s Image Stabilizer will be activated.
7 Custom ControlsN : Unlock while button pressed Even when the switch is set to the right, as long as the depthof-field preview button is held down, you can use the camera control buttons and dials restricted by [55: Multi function lock] (p.90). : Start movie recording (when k set) For movie shooting, pressing the button assigned to this function will start the movie shooting. To stop the movie shooting, press the button again. : Image replay Press <0> to play back the images.
Custom Quick Control On the standard Quick Control screen (p.64), preset shooting functions are displayed in the default layout. On the Custom Quick Control screen, you can customize the screen with your preferred shooting functions and layout. This feature is called “Custom Quick Control”. This page explains how to change the layout of the Custom Quick Control screen. Page 64 explains how to operate the Quick Control, and page 86 explains how to display the Custom Quick Control screen.
Custom Quick Control an item. 4 AddPress the button. Turn the <5> dial or use <9> to select the item to be added, then press <0>. To remove an item, select the item, then press the button. Otherwise, select [Clear all items] in step 2. For items that let you select the icon size, turn the <5> dial or use <9> to select the size, then press <0>. For items which can be positioned and for display sizes, see page 513. the item.
Custom Quick Control Sample layout Repeat steps 4 and 5 to position other items as desired. To delete an item already in position, select it, then press the button. the setting. 6 ExitPress the button to exit the setting. The screen in step 2 will reappear. Sample screen the setting screen. 7 Check Under [53: z button display options], check that [Custom Quick Control screen] has a checkmark [X] (p.86). Press the button to display the Custom Quick Control screen (p.86) and check the layout.
Custom Quick Control Available Items and Display Sizes for the Screen Layout (Vertical x horizontal cells) Item and Size 1x1 1x2 1x3 Shooting mode k Shutter speed k k Aperture k k ISO speed k k Exposure compensation/AEB setting k k k Flash exposure compensation k k k Picture Style k White balance k k White balance shift/bracketing k k Auto Lighting Optimizer k Custom Controls k AF operation k AF point selection k Metering mode k Drive mode k 2x2 2x3 k k k k
Custom Quick Control Depending on the items, the amount of displayable information and settable functions for Quick Control may vary due to their display sizes. The same item cannot be placed in multiple positions on the screen. In the mode, some menu items are not displayed. Also, some menu items cannot be set with the Quick Control. Mode Settings and Display Conditions You can also set Custom Quick Control and display the Custom Quick Control screen in the mode.
3 Registering My MenuN Under My Menu tab, you can register menu items and Custom Functions whose settings you change frequently. You can also name the registered menu tabs, and press the button to display the My Menu tab first. Creating and Adding My Menu Tab 1 Select [Add My Menu tab]. Under the [9] tab, select [Add My Menu tab], then press <0>. [OK]. 2 Select X The [MY MENU1] tab is created. You can create up to five menu tabs by repeating steps 1 and 2.
3 Registering My MenuN 2 Select [Select items to register]. the desired items. 3 Register Select the desired item, then press <0>. Select [OK] on the confirmation dialog. You can register up to six items. To return to the screen in step 2, press the button. My Menu Tab Settings You can sort and delete items under the menu tab, and rename or delete the menu tab. Sort registered items You can change the order of the registered items in My Menu.
3 Registering My MenuN Delete tab You can delete the My Menu tab currently displayed. Select [Delete tab] to delete the [MY MENU*] tab. Rename tab You can rename the My Menu tab from [MY MENU*]. 1 Select [Rename tab]. text. 2 Enter Press the button to delete any Input mode unnecessary characters. Operate the <5>, <6>, or <9> to move the and select the desired character. Then press <0> to enter it. By selecting [Aaz1@], you can change the input mode. You can enter up to 16 characters.
3 Registering My MenuN Deleting all My Menu tabs / Deleting all items You can delete all My Menu tabs or all My Menu items that you created and registered under the tabs. Delete all My Menu tabs You can delete all My Menu tabs you created. When you select [Delete all My Menu tabs], all the tabs from [MY MENU1] to [MY MENU5] will be deleted and the [9] tab will revert to its default. Delete all items You can delete only but all the items registered under the [MY MENU1] to [MY MENU5] tabs.
3 Registering My MenuN Menu Display Settings You can select [Menu display] to set the menu screen that is to appear first when you press the button. Normal display Displays the last displayed menu screen. Display from My Menu tab Displays with the [9] tab selected. Display only My Menu tab Only the [9] tab is displayed. (The z, 2, 3, 5, and 8 tabs will not be displayed.
w: Registering Custom Shooting ModesN You can register current camera settings, such as the shooting functions, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial’s , , and positions. 1 Select [Custom shooting mode (C1-C3)]. Under the [55] tab, select [Custom shooting mode (C1-C3)], then press <0>. 2 Select [Register settings]. the desired items. 3 Register Select the Custom shooting mode to be registered, then press <0>.
w: Registering Custom Shooting ModesN HDR movie shooting and My Menu settings will not be registered under Custom shooting modes. Even in the , , and modes, you can still change shooting function settings and menu settings. By pressing the button, you can check which shooting mode is registered under , , and (p.87).
w: Registering Custom Shooting ModesN [z4 (Movie shooting)] Movie Servo AF, AF method, Grid display, Movie recording quality (excluding 24.
15 Reference This chapter provides reference information for system accessories, camera features, etc. Certification Logo Select [55: Certification Logo Display] and press <0> to display some of the logos of the camera’s certifications. Other certification logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.
System Map ST-E2 ST-E3-RT Dioptric Adjustment Lenses Eg 270EX II 430EX III-RT/ 600EX II-RT 430EX III Macro Ring Lite MR-14EX II Macro Twin Lite MT-24EX Bundled Accessories Eyecup Eg Anti-Fog Eyepiece Eg Cable protector Wide Strap Angle Finder C Battery Pack LP-E6N*1 Battery Charger LC-E6 AC Adapter DC Coupler AC-E6N*2 DR-E6*2 Hand Strap E2 Battery Grip BG-E20 Battery Magazine BGM-E20 for LP-E6N/LP-E6 (attached to BG-E20) 524 Car Battery Cable CB-570 Car Battery Charger CBC-E6
System Map Headphones Directional Stereo Microphone DM-E1 Timer Remote Remote Switch Controller RS-80N3 TC-80N3 Wireless Controller LC-5 EF lenses Remote Controller RC-6 HDMI Cable HTC-100 (2.9 m/9.5 ft.) Wireless File Transmitter WFT-E7 (Ver. 2)*3/ WFT-E7*4 EOS DIGITAL Solution Disk Wireless LAN access point Interface Cable IFC-150U II (1.5 m/4.9 ft.) TV/Video Connect Station CS100 Wireless LAN adapter Ethernet port Interface Cable IFC-500U II*5 (4.7 m/15.4 ft.
3 Checking the Battery Information You can check the conditions of the battery you are using on the LCD monitor. Each Battery Pack LP-E6N/LP-E6 has a unique serial number, and you can register multiple battery packs to the camera. When you use this feature, you can check the registered batteries’ approximate remaining capacity and usage history. Select [Battery info.]. Under the [53] tab, select [Battery info.], then press <0>. X The battery info. screen will appear.
3 Checking the Battery Information Registering Batteries to the Camera You can register up to six LP-E6N/LP-E6 batteries to the camera. To register multiple batteries to the camera, follow the procedure below for each battery. 1 Press the button. With the battery info. screen displayed, press the button. X The battery history screen will appear. X If the battery is not registered, it will be grayed out. [Register]. 2 Select X The confirmation dialog will appear. [OK].
3 Checking the Battery Information Labeling Serial Numbers on Batteries It is convenient to label each registered Battery Pack LP-E6N/LP-E6 with their serial numbers, using commercially-available labels. 1 Serial number Write the serial number on a label. Write the serial number displayed on the battery history screen on a label approx. 25 mm x 15 mm / 1.0 in. x 0.6 in. in size. 7c40 0300 the battery and affix the 2 Remove label. Set the power switch to <2>.
3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery You can check the remaining capacity of any battery (even when not installed) and also when it was last used. Serial number Date last used Look for the serial number. Refer to the battery’s serial number label and look for the battery’s serial number on the battery history screen. X You can check the respective battery’s remaining capacity and the date when it was last used.
Using a Household Power Outlet You can power the camera with a household power outlet by using the DC Coupler DR-E6 and AC Adapter AC-E6N (each sold separately). 1 Place the cord in the groove. Carefully insert the DC coupler’s cord into the groove without damaging the cord. the DC coupler. 2 Insert Open the battery compartment cover DC coupler cord hole and open the DC coupler cord hole cover. Insert the DC coupler securely until it locks and put the cord through the hole. Close the cover.
Using a Household Power Outlet Do not use an AC adapter other than the AC-E6N (sold separately). While the camera’s power switch is on, do not connect or disconnect the power cord or connector, or disconnect the DC coupler. After using the camera, unplug the power plug from the power outlet. AC Adapter Kit ACK-E6 can also be used.
H Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card manufacturer.
H Using Eye-Fi Cards the connection 4 Display information. Select [Connection info.], then press <0>. the [Access point SSID:]. 5 Check Check that an access point is displayed for [Access point SSID:]. You can also check the Eye-Fi card’s MAC address and firmware version. Press the button to exit the menu. the picture. 6 Take X The picture is transferred and the Transmission status [H] icon switches from gray (not connected) to one of the icons in the sequence below.
H Using Eye-Fi Cards Cautions for Using Eye-Fi Cards If [Wi-Fi/NFC] under [54: Wireless communication settings] [Built-in wireless settings] is set to [Enable], image transfer with an Eye-Fi card will not be possible. If “J” is displayed, an error occurred while retrieving the card information. Turn the camera’s power switch off and on again. Even if [Eye-Fi trans.] is set to [Disable], it may still transmit a signal.
MEMO 535
Function Availability Table by Shooting Mode Still Photo Shooting o: Set automatically k: User selectable Function All image quality settings selectable Dual Pixel RAW d s f a F k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k
Function Availability Table by Shooting Mode Function A d s f a F Single shooting k k k k k k k o k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k*5 k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k k High-speed continuous shooting Low-speed continuous shooting Drive Silent single shooting*2 Silent continuous shooting*2 10-sec.
Function Availability Table by Shooting Mode Movie Shooting o: Set automatically k: User selectable : Not selectable/Disabled A d/F y k Select all movie recording qualities k k k k k HDR movie shooting k k k k k Time-lapse movie k k k k k o o o o k o k k k k k k k k o k k k k Preset k k k k Custom k k k k Color temperature setting k k k k Correction k k k k Function ISO speed Picture Style Automatically set/Auto f Automatically set/Auto a
Function Availability Table by Shooting Mode Function Metering A d/F y k s f a o o o o o k k k k*4 M Program shift Exposure Exposure compensation k k k *5 o k k k k k k k k Time code k k k k k HDMI output k k k k k GPS function k k k k k Quick Control k k k k k Touch control k k k k k AE lock Sound recording*3 Auto Custom *1: Cannot be set for 4K movie shooting. *2: Multi Shot Noise Reduction cannot be set.
Menu Settings Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Image quality Page 1 / 41 / 61 73, 83, 74, 84, 7a, 8a, b, c 169 Dual Pixel RAW* Disable / Enable Image review time Off / 2 sec. / 4 sec. / 8 sec.
Menu Settings z: Shooting 2 (Red) Page Exposure compensation/AEB setting*1 1/3- and 1/2-stop increments, ±5 stops (AEB ±3 stops) 255 257 ISO speed settings ISO speed / Range for stills / Auto range / Minimum shutter speed 177 180 181 182 Auto Lighting Optimizer White balance Disable / Low / Standard / High Disabled in M or B modes Q (Ambience priority) / Qw (White priority) / W/E/R/Y/U/D/O/P (Approx.
Menu Settings z: Shooting 3 (Red) Page Picture Style DAuto / PStandard / QPortrait / RLandscape / uFine Detail / SNeutral / UFaithful / VMonochrome / WUser Def.
Menu Settings z: Shooting 4*1 (Red) Page Interval timer Disable / Enable (Interval / Number of shots) 281 Bulb timer*2 Disable / Enable (Exposure time) 261 Anti-flicker shooting Disable / Enable 215 Mirror lockup Disable / Enable 276 *1: In the mode, these menu options are displayed under [z2]. *2: Settable in the mode.
Menu Settings 2: AF1 (Purple) Page Case 1 Versatile multi purpose setting 128 Case 2 Continue to track subjects, ignoring possible obstacles 128 Case 3 Instantly focus on subjects suddenly entering AF points 129 Case 4 For subjects that accelerate or decelerate quickly 129 Case 5 For erratic subjects moving quickly in any direction 130 Case 6 For subjects that change speed and move erratically 131 AI Servo 1st image priority Release priority / Equal priority / Focus priority 136 AI S
Menu Settings 2: AF4 (Purple) Page Lens drive when AF impossible Continue focus search / Stop focus search 141 Selectable AF point All points / Only cross-type AF points / 15 points / 9 points 142 Select AF area selection mode Manual selection: Spot AF / Manual selection: 1 point AF / Expand AF area: / Expand AF area: Surround / Manual selection: Zone AF / Manual selection: Large Zone AF / Auto selection AF 143 AF area selection method S 9 M-Fn button / S 9 Main Dial 144 Orientation linked AF
Menu Settings 3: Playback 1 (Blue) Page Protect images Protect images 412 Rotate image Rotate images 411 Erase images Erase images 440 Print order Specify images to be printed (DPOF) 471 Photobook set-up Specify images for a photobook 476 Image copy Copy images between cards 435 RAW image processing Process 1 images 446 3: Playback 2 (Blue) Cropping Partially crop JPEG images 454 Resize Downsize JPEG image’s pixel count 452 Rating [OFF] / l / m / n / o / p 416 Slide show Se
Menu Settings 3: Playback 3 (Blue) Page Highlight alert Disable / Enable 401 AF point display Disable / Enable 402 Playback grid Off / 3x3 l / 6x4 m / 3x3+diag n 396 Histogram display Brightness / RGB 402 Movie playback count* Recording time / Time code 366 1x (no magnification) / 2x (magnify from center) / 4x (magnify from center) / 8x (magnify Magnification (Approx.
Menu Settings 5: Set-up 2 (Yellow) Auto power off LCD brightness Page 1 min. / 2 min. / 4 min. / 8 min. / 15 min. / 30 min. / Disable Auto: Adjustable to one of three brightness levels Manual: Adjustable to one of seven brightness levels 76 442 LCD color tone 1: Warm tone / 2: Standard / 3: Cool tone 1 / 4: Cool tone 2 443 Date/Time/Zone Date (year, month, day) / Time (hr., min., sec.
Menu Settings 5: Set-up 3 (Yellow) Page Video system For NTSC / For PAL 352 432 Battery information Power source / Remaining capacity / Shutter count / Recharge performance 526 Auto cleaning f: Enable / Disable Sensor cleaning Clean now f 458 Clean manually 463 z button display options Displays camera settings / Electronic level / Quick Control screen / Custom Quick Control screen 86 Custom Quick Control Start editing layout / Revert layout to default / Clear all items 510 Live View info
Menu Settings *1: Not settable if [Movie rec quality]’s [24.00p] is set to [Enable] under [z4 (Movie)] tab. *2: Displayed contents vary depending on the [53: Video system] setting. *3: For details, refer to “Wi-Fi (Wireless Communication) Function Instruction Manual” (p.4). When using the GPS function, built-in Wi-Fi (wireless commnunication) function or Wireless File Transmitter WFT-E7 (Ver.
Menu Settings 8: Custom Functions (Orange) C.Fn1: Exposure 482 C.Fn2: Exposure C.Fn3: Display/ Operation 488 Customize camera functions as desired C.Fn4: Others C.
Menu Settings Movie Shooting z: Shooting 2 (Movie) (Red) ISO speed settings Page ISO speed / Range for movies / Range for H 379 z: Shooting 4*1 (Movie) (Red) Movie Servo AF Enable / Disable 380 AF method u+Tracking / FlexiZone - Multi / FlexiZone Single 382 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 382 MOV / MP4 351 Movie recording size*2 • 4K (4096x2160) / Full HD (1920x1080) • NTSC: 59.94p / 29.97p / 23.98p Movie recording quality PAL: 50.00p / 25.
Menu Settings Page Movie Servo AF Speed*4 Movie Servo AF track sensitivity*4 When active: Always on / During shooting AF speed: Slow (-7/-6/-5/-4/-3/-2/-1) / Standard / Fast (+1/+2) Locked on (-3/-2/-1) / 0 / Responsive (+1/+2/+3) 383 384 *1: In the mode, these menu options are displayed under [z2]. *2: The movie recording size will vary depending on the [MOV/MP4], [24.00p], and [High Frame Rate] settings and the [53: Video system] setting. *3: High Frame Rate movies will be shot in HD quality.
Troubleshooting Guide If a problem occurs with the camera, first consult this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power-Related Problems The battery does not recharge. If the battery’s remaining capacity is 94% or higher, the battery will not be recharged (p.526). Do not use any battery other than genuine Canon Battery Pack LP-E6N/LP-E6. The charger’s lamp blinks at high speed.
Troubleshooting Guide The access lamp still lights or blinks even when the power switch is <2>. If the power is turned off while an image is being recorded to the card, the access lamp will remain on or continue to blink for a few seconds. When the image recording is completed, the power will turn off automatically. [Does this battery/do these batteries display the Canon logo?] is displayed. Do not use any battery other than genuine Canon Battery Pack LP-E6N/LP-E6. Remove and install the battery again (p.
Troubleshooting Guide The camera turns off by itself. Auto power off is in effect. If you do not want auto power off to take effect, set [52: Auto power off] to [Disable] (p.76). Even if [52: Auto power off] is set to [Disable], the LCD monitor will still turn off after the camera is left idle for approx. 30 min. (The camera’s power does not turn off.) Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-S or EF-M lenses (p.55). The viewfinder is dark.
Troubleshooting Guide The card cannot be used. If a card error message is displayed, see page 48 or 573. An error message is displayed when the card is inserted in another camera. CF cards with a capacity greater than 128 GB and SDXC cards are formatted in exFAT. This means that if you format a card with this camera and then insert it into another camera, an error may be displayed and it may not be possible to use the card. I have to press the shutter button twice completely to take a picture.
Troubleshooting Guide There are fewer AF points or the Area AF frame shape is different. Depending on the attached lens, the number of usable AF points and patterns and Area AF frame’s shape vary. The lenses are categorized into 11 groups from A to K (p.115). Check which group your lens belongs to. Using a lens in groups G to K will have fewer usable AF points (p.118-121). The AF point is blinking or two AF points are displayed.
Troubleshooting Guide The continuous shooting speed is slow. The continuous shooting speed for high-speed continuous shooting may decrease depending on the power source type, battery level, temperature, flicker reduction, Dual Pixel RAW shooting, Digital Lens Optimizer, shutter speed, aperture, subject conditions, brightness, AF operation, lens, flash use, shooting function settings, etc. For details, see pages 160-162. The maximum burst during continuous shooting is lower.
Troubleshooting Guide Dual Pixel RAW shooting is not possible. Set [z1: Dual Pixel RAW] to [Enable], and set [z1: Image quality] to 1 or 1+JPEG. ISO 100 cannot be set. ISO speed expansion cannot be selected. If [z3: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200 - ISO 32000. Even if you set [Range for stills] to expand the setting range, you cannot select L (equivalent to ISO 50), H1 (equivalent to ISO 51200), or H2 (equivalent to ISO 102400).
Troubleshooting Guide The shot image is not displayed during multiple-exposure shooting. If [On:ContShtng] is set, image review immediately after image capture or image playback is not possible during shooting (p.268). The multiple-exposure image is shot in 1 quality. When the image-recording quality is set to 41 or 61, the multiple-exposure image will be recorded in 1 quality (p.275). When I use the mode with flash, the shutter speed becomes slow.
Troubleshooting Guide Flash exposure compensation cannot be set. If flash exposure compensation is already set with the Speedlite, flash exposure compensation cannot be set with the camera. When the external Speedlite’s flash exposure compensation is canceled (set to 0), flash exposure compensation can be set with the camera. High-speed sync cannot be set in the mode. Under [z1: External Speedlite control], set [Flash sync. speed in Av mode] to [Auto] (p.290).
Troubleshooting Guide During movie shooting, the red E icon is displayed. It indicates that the camera’s internal temperature is high. If the red icon is displayed, it indicates that the movie shooting will soon stop automatically (p.391). Movie shooting stops by itself. If the card’s writing speed is slow, movie shooting may stop automatically. For cards that can record movies, see page 356. To find out the card’s writing speed, refer to the card manufacturer’s Web site.
Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. For viewfinder shooting and Live View shooting, the ISO speed will be set according to the setting of [Range for stills] under [z2: ISO speed settings] (p.180). For movie shooting, the ISO speed will be set according to the setting of [Range for movies] or [Range for H] under [z2: ISO speed settings] (p.379). The exposure changes during movie shooting.
Troubleshooting Guide The subject looks distorted during movie shooting. If you move the camera to the left or right (panning) or shoot a moving subject, the image may look distorted. The problem may be more noticeable in time-lapse movie shooting. The movie does not record the sound. High Frame Rate movies do not record sound. The time code is not appended. For High Frame Rate movie shooting, if [Free run] is set for [Count up] under [z5: Time code] (p.365), the time code will not be appended.
Troubleshooting Guide Operation Problems I cannot change the setting with the <6> dial, <5> dial, <9>,
, or . Set the switch to the left (lock release, p.62). Check the [55: Multi function lock] setting (p.90). Touch operation is not possible. Check if [52: Touch control] is set to [Standard] or [Sensitive] (p.72). A camera button or dial does not work as expected. Check the [83: Custom Controls] setting (p.495). Display Problems The menu screen shows fewer tabs and options.
Troubleshooting Guide The file name’s first character is an underscore (“_”). Set [z2: Color space] to [sRGB]. If [Adobe RGB] is set, the first character will be an underscore (p.217). The fourth character in the file name changes. [51: File name] is set to [*** + image size]. Select the camera’s unique file name (preset code) or the file name registered under User setting 1 (p.220). The file numbering does not start from 0001.
Troubleshooting Guide [###] is displayed. If the number of images recorded on the card exceeds the number the camera can display, [###] will be displayed. In the viewfinder, the AF point display speed is slow. In low temperatures, the display speed of the AF points may become slower due to the AF point display device’s (liquid crystal) characteristics. The display speed will return to normal at room temperature. The LCD monitor does not display a clear image.
Troubleshooting Guide Playback Problems Part of the image blinks in black. [33: Highlight alert] is set to [Enable] (p.401). A red box is displayed on the image. [33: AF point disp.] is set to [Enable] (p.402). During image playback, the AF points are not displayed. When you play back an image applied with distortion correction (p.209), the AF points are not displayed. The image cannot be erased. If the image is protected, it cannot be erased (p.412). The movie cannot be copied.
Troubleshooting Guide The movie appears to freeze momentarily. If there is a drastic change in the exposure level during autoexposure movie shooting, the recording will stop momentarily until the brightness stabilizes. In such a case, shoot in the mode (p.340). The movie plays in slow motion. Since the High Frame Rate movie will be recorded as a 29.97 fps/ 25.00 fps movie file, it will play back in slow motion at 1/4 speed. No picture on the TV set.
Troubleshooting Guide My card reader does not recognize the card. Depending on your card reader and computer OS, large-capacity CF cards or SDXC cards may not be properly recognized. In such a case, connect your camera to the computer with the interface cable, then transfer the images to the computer using EOS Utility (EOS software, p.598). I cannot process the RAW image. 41 and 61 images cannot be processed with the camera. Use Digital Photo Professional (EOS software, p.598) to process those images.
Troubleshooting Guide Sensor Cleaning Problems The shutter makes a sound during sensor cleaning. When you select [Clean nowf], the shutter will make a mechanical sound during the cleaning, but the picture will not be recorded to the card (p.458). Automatic sensor cleaning does not work. If you repeatedly turn the power switch <1> and <2> within a short time period, the icon may not be displayed (p.49). Computer Connection Problems I cannot transfer images to a computer.
Error Codes Error number If there is a problem with the camera, an error message will appear. Follow the onscreen instructions. Cause and countermeasures Number 01 02 Error Message and Solution Communications between the camera and lens is faulty. Clean the lens contacts. Î Clean the electrical contacts on the camera and lens, use a Canon lens, or remove and install the battery again (p.27, 28, 44). Card* cannot be accessed. Reinsert or replace card * or format card * with the camera.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera CF cards (Type I, UDMA Mode 7 supported) SD/SDHC*/SDXC* memory cards * UHS-I cards compatible. Approx. 36.0 x 24.0 mm Canon EF lenses * Excluding EF-S and EF-M lenses (The effective angle of view of a lens is approximately equivalent to that of the focal length indicated.
Specifications • Image Processing During Shooting Picture Style: White balance: Automatic image brightness correction: Noise reduction: Highlight tone priority: Lens aberration correction: Auto, Standard, Portrait, Landscape, Fine Detail, Neutral, Faithful, Monochrome, User Defined 1 - 3 Auto (Ambience priority), Auto (White priority), Preset (Daylight, Shade, Cloudy, Tungsten light, White fluorescent light, Flash), Custom, Color temperature setting (approx.
Specifications • Autofocus (during viewfinder shooting) Type: TTL secondary image-registration, phase-difference detection with the dedicated AF sensor AF points: Max. 61 points (Cross-type AF point: Max. 41 points) * Number of available AF points, Dual cross-type AF points, and Cross-type AF points vary depending on the lens used. * f/2.8-sensitive, Dual cross-type AF at five center vertical AF points (AF group: With Group A lenses) Focusing brightness EV -3 - 18 (Conditions: f/2.
Specifications Shooting mode: ISO speed (Recommended exposure index): ISO speed settings: Exposure compensation: AE lock: Flicker reduction: Interval timer: Bulb timer: Scene Intelligent Auto, Program AE, Shutter-priority AE, Aperture-priority AE, Manual exposure, Bulb exposure, Custom shooting modes (C1/C2/C3) Scene Intelligent Auto: ISO 100 - ISO 12800 set automatically P, Tv, Av, M, B: ISO Auto, ISO 100 - ISO 32000 manual setting (in 1/3- or whole-stop increments), and expansion to L (equivalent to
Specifications • Drive System Drive mode: Continuous shooting speed: Max. burst: 578 Single shooting, High-speed continuous shooting, Lowspeed continuous shooting, Silent single shooting, Silent continuous shooting, 10-sec. self-timer/remote control, 2sec. self-timer/remote control High-speed continuous shooting: Max. approx. 7.0 shots/ sec.
Specifications • External Speedlite Compatible Speedlites: Flash metering: Flash exposure compensation: FE lock: PC terminal: Flash control: EX-series Speedlites E-TTL II autoflash ±3 stops in 1/3- or 1/2-stop increments Provided Provided Flash function settings, Flash C.Fn settings • Live View Shooting Focus method: AF method: Dual pixel CMOS AF Face+Tracking, FlexiZone - Multi, FlexiZone - Single Manual focusing (approx.
Specifications Bit rate: [MOV] 4K (29.97p/25.00p/24.00p/23.98p) : Approx. 500 Mbps Full HD (59.94p/50.00p)/ALL-I : Approx. 180 Mbps Full HD (59.94p/50.00p)/IPB : Approx. 60 Mbps Full HD (29.97p/25.00p/24.00p/23.98p)/ALL-I : Approx. 90 Mbps Full HD (29.97p/25.00p/24.00p/23.98p)/IPB (Standard) : Approx. 30 Mbps HD (119.9p/100.0p)/ALL-I : Approx. 160 Mbps [MP4] Full HD (59.94p/50.00p)/IPB (Standard) : Approx. 60 Mbps Full HD (29.97p/25.00p/24.00p/23.98p)/IPB (Standard) : Approx. 30 Mbps Full HD (29.97p/25.
Specifications Focusing brightness range:EV -4 - 18 (at room temperature, ISO 100, One-Shot AF) Metering mode: Center-weighted average and Evaluative metering with the image sensor * Automatically set by the focus method Metering brightness EV 0 - 20 (at room temperature, ISO 100, with centerrange: weighted average metering) Autoexposure shooting (Program AE for movie shooting), Exposure control: Shutter-priority AE, Aperture-priority AE, Manual exposure Exposure compensation: ±3 stops in 1/3- or 1/2-stop
Specifications Headphones: Grid display: HDR movie shooting: Time-lapse movie: 2-screen display: HDMI output: Remote control shooting: Accessory mount: Still photo shooting: Headphone terminal provided, sound volume adjustable 3 types Provided Shooting interval and shot count settable Required shooting time period, playback length, and remaining card capacity can be checked LCD monitor and HDMI output movie displayable simultaneously Image without information can be output. * Auto / 59.94i/50.00i / 59.
Specifications Highlight alert: AF point display: Overexposed highlights blink Provided (may not be displayed depending on shooting conditions) Grid display: 3 types Magnified view: Approx. 1.
Specifications • GPS Functions Compatible satellites: GPS satellites (USA), GLONASS satellites (Russia), Quasi-Zenith Satellite System (QZSS) MICHIBIKI (Japan) Mode 1, Mode 2 GPS signal reception modes: Geotag information Latitude, Longitude, Elevation, Coordinated Universal appended to image: Time (UTC), Satellite signal acquisition status Position update interval: 1 sec., 5 sec., 10 sec., 15 sec., 30 sec., 1 min., 2 min., 5 min.
Specifications • Power Battery: Battery information: Number of possible shots: Movie shooting time: Battery Pack LP-E6N/LP-E6, quantity 1 * AC power usable with household power outlet accessories. Power source, Battery level, Shutter count, Recharge performance, Battery registration indicated With viewfinder shooting: Approx. 900 shots at room temperature (23°C/73°F), approx. 850 shots at low temperatures (0°C/32°F) With Live View shooting: Approx. 300 shots at room temperature (23°C/73°F), approx.
Specifications • Battery Pack LP-E6N Type: Rechargeable lithium-ion battery Rated voltage: 7.2 V DC Battery capacity: 1865 mAh Working temperature 0°C - 40°C / 32°F - 104°F range: Working humidity: 85% or less Dimensions (W x H x D):Approx. 38.4 x 21.0 x 56.8 mm / 1.51 x 0.83 x 2.24 in. Weight: Approx. 80g / 2.82 oz. (excluding protective cover) • Battery Charger LC-E6 Compatible battery: Battery Pack LP-E6N/LP-E6 Recharge time: Approx. 2 hr. 30 min.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. CompactFlash is a trademark of SanDisk Corporation. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Third party software This product includes third party software. expat.
Use of Genuine Canon Accessories Is Recommended This product is designed to achieve optimum performance when used with genuine Canon accessories. Therefore, using this product with genuine accessories is highly recommended. Canon shall not be liable for any damage to this product and/or accidents such as malfunction, fire, etc., caused by the failure of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Digital Camera Model DS126601 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
USA and Canada only: The Lithium ion/polymer battery that powers the product is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery. For CA, USA only Included lithium battery contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATION.
MEMO 592
MEMO 593
MEMO 594
16 Downloading Images to a Computer / Software This chapter explains how to transfer images from the camera to a computer, gives an overview of the software on the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on a computer. It also explains how to view the PDF files on the Software Instruction Manual CD-ROM.
Downloading Images to a Computer You can use EOS software to download the images in the camera to a computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer 1 Install the software (p.599). the provided interface cable 2 Use to connect the camera to the computer. Use the interface cable provided with the camera. When connecting the cable to the camera, use the cable protector (p.38).
Downloading Images to a Computer Downloading Images with a Card Reader You can use a card reader to download images to a computer. 1 Install the software (p.599). the card into the card 2 Insert reader. Digital Photo Professional to 3 Use download the images. For details, refer to the Digital Photo Professional Instruction Manual (p.600). When downloading images from the camera to a computer with a card reader without using EOS software, copy the DCIM folder on the card to the computer.
Software Overview EOS DIGITAL Solution Disk Various software for EOS DIGITAL cameras is contained on the EOS DIGITAL Solution Disk. (Software Instruction Manuals are not contained on the EOS DIGITAL Solution Disk. See page 600.) EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely from the computer connected to the camera.
Installing the Software Downloading from the Canon Web site You can download the following software and Software Instruction Manuals from the Canon Web site. www.canon.com/icpd EOS MOVIE Utility This software enables you to play back the movies you shot, consecutively play back movie files that were split up, and merge the split movie files and save it as a single file. You can also grab movie frames and save them as still photos.
Software Instruction Manual This disk contains the Software Instruction Manuals. You can copy and view the Software Instruction Manual (PDF files) as shown below. You can also download the Software Instruction Manuals (PDF files) from the Canon Web site. www.canon.com/icpd 1 Insert the [Software INSTRUCTION MANUAL] CD-ROM into the computer. 2 Double-click the CD-ROM icon. 3 Copy the [English] folder to the computer. Instruction Manuals (PDF files) with the names below are copied.
Index Numerics 10- or 2-sec. self-timer ..................163 w 1280x720 (movie) ..................352 L 1920x1080 (movie)................352 4, 9, 36, or 100 images .................403 H 4096x2160 (movie).................352 4K frame capture ..........................427 A AF point selection ............ 107, 503 AF sensor................................. 113 Area AF frame.................. 105, 111 Beeper ....................................... 76 Color information......................
Index Aperture-priority AE ..............248, 336 Area AF frame ......................105, 111 Aspect ratio...................................310 buSY (BUSY) ....................... 174, 205 C Attenuator .....................................363 w (Custom shooting) .................. 520 Auto (D)....................................184 Cable protector............................... 38 Auto Lighting Optimizer ..........93, 201 Camera Auto playback ...............................429 Camera shake ....
Index My Menu...................................518 Dioptric adjustment......................... 57 Clipped highlights..........................401 Direct selection (AF point) ............ 503 CLn ...............................................463 Distortion correction ..................... 209 Color space...................................217 Downloading images to Color temperature .................192, 197 a computer ................................... 596 Color tone ...........................
Index F Flash mode .................................. 291 Faithful (U) ...............................185 FAT32 .....................................74, 360 FE lock..........................................286 Feature guide..................................91 FEB (Flash Exposure Bracketing)....................................293 File extension................................222 File name ......................................220 Underscore “_” .................217, 222 File size.........................
Index HDMI CEC ....................................433 Highlight alert ........................... 401 HDR movie....................................369 Histogram................................. 402 HDR shooting................................263 Index display ............................ 403 Headphones..................................363 Jump display Help.................................................91 (image browsing) ..................... 404 High-Definition ......................
Index Range for H ...........................379 Peripheral illumination Setting increments....................482 correction ................................. 207 Range for stills..........................180 Light (IPB) .................................... 355 iTR AF...........................................147 Live View Shooting................. 98, 297 AF operation ............................ 314 J Aspect ratio.............................. 310 JPEG ....................................
Index Manual selection Compression method............... 355 (AF point) ......................104, 107, 109 Drop frame ............................... 368 Maximum burst .....................171, 174 Editing ...................................... 425 Medium Editing out first and (image-recording quality) ..............171 last scenes ............................... 425 Memory cards 9 Cards Enjoying movies....................... 420 Menu ...............................................
Index Servo AF ..................................380 Shutter speed ...........335, 340, 343 Shutter-priority AE ....................335 Orientation linked AF point ........... 144 P Sound recording/ P (Program AE).................... 244, 334 Sound-recording level ..............362 PAL............................... 352, 432, 549 Time code.................................365 Partial metering ............................ 253 Time-lapse movie .....................371 PC terminal ...................
Index Q Q(Quick Control) ...64, 308, 350, 418 Quick Control Dial ...........................60 R Serial number ................. 30, 155, 526 Servo AF AI Servo AF.............................. 102 Movie Servo AF ....... 380, 383, 384 SERVO (LV) ............................. 315 Rating mark...................................415 Sharpness .................................... 188 RAW..............................169, 171, 173 Shooting information display ........ 398 RAW image processing ..............
Index Spot AF point ..........................31, 109 User Def. (W) ........................... 185 Spot metering................................254 UTC (Coordinated Universal S-RAW Time) ............................................ 228 (Small RAW) .........169, 171, 172, 173 sRGB ............................................217 V Standard (IPB) ..............................355 Vertical image auto rotation.......... 444 Standard (P).............................184 Video system................
MEMO 611
MEMO 612
EOS 5D Mark IV (WG) Wi-Fi (Wireless Communication) Function Basic Instruction Manual In Wi-Fi (Wireless Communication) Function Basic Instruction Manual, basic operation procedures for easy-to-use “Communicate with a smartphone” and “Save images to Connect Station” are explained.
Introduction What You Can Do Using the Wi-Fi (Wireless Communication) Functions (1) Communicate with a smartphone (CANON iMAGE GATEWAY) (2) Save images to Canon Connect Station (6) Send images to a Web service (3) Operate remotely using EOS Utility (5) Transfer images to an FTP server (4) Print images using a Wi-Fi printer W-2
Introduction (1) q Communicate with a smartphone Connect the camera to a smartphone or tablet wirelessly and use the dedicated application “Camera Connect” to operate the camera remotely or view images stored in the camera. In this manual and on the camera’s LCD monitor, “smartphone” refers to smartphones and tablets. NFC*-enabled smartphones can be connected by touching them to the camera.
Introduction Easy Connection Using the NFC Function This camera can be easily connected to an NFC-enabled smartphone or Connect Station (sold separately) using the NFC function. For details, see page W-16. Instruction Manual For how to use [Remote control (EOS Utility)], [Print from Wi-Fi printer], [Transfer images to FTP server], and [Upload to Web service] and for more detailed procedures, refer to the “Wi-Fi (Wireless Communication) Function Instruction Manual” PDF file.
Contents Introduction W-2 What You Can Do Using the Wi-Fi (Wireless Communication) Functions... W-2 Conventions Used in this Manual ................................................ W-6 1 Preparation and Basic Operation W-7 Registering a Nickname............................................................... W-8 Basic Operation and Settings .................................................... W-11 NFC Function.............................................................................
Conventions Used in this Manual In this manual, the terms “wireless” and “wireless LAN” are used as general terms for Wi-Fi and Canon’s original wireless communication functions. The term “access point” indicates wireless LAN terminals (wireless LAN access points, wireless LAN routers, etc.) that relay wireless LAN connection. Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <9> : Indicates the Multi-controller. <0> : Indicates the Setting button.
1 Preparation and Basic Operation This chapter describes how to register a nickname (for identification) necessary for using the camera’s wireless functions and the basic operations.
Registering a Nickname First, set the camera’s nickname (for identification). When the camera is connected to another device wirelessly, the nickname will be displayed on the device. Be sure to set a nickname as otherwise you cannot set the wireless functions. 1 Select [Communication settings]. Press the button, select [Communication settings] under the [54] tab, and press <0>. 2 Select [Built-in wireless settings]. 3 Select [Nickname].
Registering a Nickname a nickname. 4 Enter For instructions on entering characters, see the next page. When using the default nickname (the camera name), proceed to step 5. Otherwise, enter any characters between 1 to 10 characters in length. the setting. 5 Exit When you are finished, press the button. Select [OK] on the confirmation dialog and press <0> to return to the menu screen. Since the nickname is a required wireless setting, you cannot delete all the characters.
Registering a Nickname Virtual Keyboard Operation Changing the entry area Press the button to toggle between the top and bottom entry areas. Moving the cursor Use <5> or <9> in the top area to move the cursor. Entering text In the bottom area, use <5> or <9> to select a character, then press <0> to enter it. You can check how many characters you have entered and how many more can be entered by referring to [*/*] on the upper right of the screen.
Basic Operation and Settings The basic operation for using the camera’s wireless functions is explained here. Follow the procedures below. 1 Select [Communication settings]. Press the button, select [Communication settings] under the [54] tab, and press <0>. 2 Select [Built-in wireless settings]. 3 Select [Wi-Fi/NFC]. [Enable]. 4 Select When a nickname (for identification) is not registered, a registration screen is displayed. See page W-8 to register a nickname.
Basic Operation and Settings 5 Select [Wi-Fi function]. the Wi-Fi function to 6 Select connect to. Use <5> or <9> to select an item, then press <0>. When the connection settings are not registered, the setting screen is displayed. When the connection settings are already registered, the reconnection screen is displayed (p.W-42). When using the NFC function, see page W-16.
Basic Operation and Settings [Wi-Fi/NFC] Set whether to [Enable] or [Disable] the wireless functions. You can also set whether to enable or disable the NFC function. Set to [Enable] to enable the selection of [Wi-Fi function], [Send images to smartphone], and [Clear settings]. When the use of electronic devices and wireless devices is prohibited, such as on board airplanes or in hospitals, set it to [Disable].
Basic Operation and Settings When multiple exposures or time-lapse movie is set, you cannot select [54: Communication settings]. Interface Cable Connection Cautions During a wireless LAN connection, you cannot use the camera by connecting it to Connect Station, a computer, a wireless file transmitter, or another device with a cable. Terminate the connection before connecting a cable.
Basic Operation and Settings Wireless Connection Status Wireless connection status can be checked on the camera’s LCD monitor and LCD panel.
NFC Function Using an NFC-enabled smartphone or Connect Station enables you to do the following: Touch a smartphone to the camera to easily connect them wirelessly (p.W-21). While playing back images on the camera, touch a smartphone to the camera to send a captured image to the smartphone (p.W-31). Hold the camera close to Connect Station (sold separately) to easily connect them wirelessly (p.W-44). When using the NFC function, follow the steps below to set the camera’s NFC setting.
NFC Function [X] to [Allow NFC 4 Add connections]. Displayed when [Wi-Fi/NFC] is set to [Enable]. Press the button to add or remove [X]. Add [X], then press <0>. When a nickname (for identification) is not registered, a registration screen is displayed (p.W-8). When establishing wireless communications using the NFC function, see the following pages.
Preparation for Smartphones To use [q] (Connect to smartphone), a smartphone on which iOS or Android is installed is necessary. In addition, the dedicated application Camera Connect (free of charge) must be installed on the smartphone. Camera Connect can be downloaded from the App Store or Google Play. For the operating system versions supported by Camera Connect, refer to the download site of Camera Connect.
2 Easy Connection to a Smartphone Communicating with a smartphone enables you to perform the following: • View images stored in the camera on a smartphone or save viewed images to a smartphone. • Operate the camera to take a picture or change camera settings using a smartphone. • Send images to a smartphone from the camera. This section explains how to connect the camera directly to a smartphone via Wi-Fi. Install Camera Connect on the smartphone before setting up a connection (p.W-18).
Connection Method When the smartphone is NFC-enabled: See page W-21. You can easily set up a connection using the NFC function. When the smartphone is not NFC-enabled: See page W-24. Set up a connection by selecting [Easy connection]. Smartphones labeled with the P mark are NFC-enabled. Some smartphones are not labeled with the P mark even if they are NFCenabled; if you do not know whether your smartphone is NFC-enabled, contact the manufacturer of the smartphone.
Connecting to an NFC-enabled Smartphone NFC-enabled smartphones can be connected by touching them to the camera. The operation flow is as follows. (1) Turn on the camera and smartphone. (2) Enable the NFC function on the camera and smartphone. (3) Touch the smartphone to the camera so that they come into contact with each other. For the camera’s NFC setting, see page W-16. For the smartphone’s Wi-Fi setting, NFC setting, and NFC antenna position, refer to the smartphone’s instruction manual.
Connecting to an NFC-enabled Smartphone to the camera. 3 Connect When a connection is established, The device name set on Camera Connect the screen on the left will appear on the camera’s LCD monitor. When connecting to the same smartphone, this screen will not appear again. To specify viewable images, press the button. See step 7 on page W-40 to set them. Select [OK] and press <0>. After a message is displayed, the [qWi-Fi on] screen will appear.
Connecting to an NFC-enabled Smartphone If necessary, also read “NFC Function Cautions” (p.W-17). When touching the smartphone to the camera, be careful not to drop the camera or smartphone. Do not touch the smartphone to the camera with too much force. Doing so can scratch the camera or smartphone. Just holding the smartphone close to the mark may not establish a connection. Be sure to touch the mark with the smartphone so that they come into contact with each other.
Connecting with [Easy connection] The camera and a smartphone can be directly connected via Wi-Fi. To establish connection, operations on the smartphone are required. For details, refer to the smartphone’s instruction manual. Operation on the Smartphone-1 1 Install Camera Connect on the smartphone (p.W-18). Operation on the Camera-1 [Communication settings]. 2 Select Under the [54] tab, select [Communication settings], then press <0>. 3 Select [Built-in wireless settings]. [Wi-Fi function].
Connecting with [Easy connection] [Easy connection]. 6 Select Select [OK] and press <0> to go to the next screen. Operation on the Smartphone-2 Smartphone’s screen (sample) the smartphone and 7 Operate connect it to the camera. Activate the smartphone’s Wi-Fi function, then select the SSID (network name) displayed on the camera’s LCD monitor. For the password, enter the encryption key displayed on the camera’s LCD monitor.
Connecting with [Easy connection] Camera Connect on the 8 Start smartphone. When the [Waiting to connect] screen is displayed on the camera’s LCD monitor, start Camera Connect on the smartphone. the camera to connect to 9 Select on the smartphone. Select and tap the camera to connect to from [Cameras] on Camera Connect.
Connecting with [Easy connection] Operation on the Camera-2 to the camera. 10 Connect When a connection is established, The device name set on Camera Connect the screen on the left will appear on the camera’s LCD monitor. To specify viewable images, press the button. See step 7 on page W-40 to set them. Select [OK] and press <0>. After a message is displayed, the [qWi-Fi on] screen will appear. The main window of Camera Connect will be displayed on the smartphone.
Operating the Camera Using a Smartphone You can use a smartphone with Camera Connect installed to view images stored in the camera or perform remote shooting, etc. Camera Connect Main Window The main functions of Camera Connect are described below. Touch the screen to learn the operation procedures. [Images on camera] Images stored in the camera can be viewed. Images stored in the camera can be saved on a smartphone. Operations such as deletion can be performed on images stored in the camera.
Operating the Camera Using a Smartphone Terminating the Connection To terminate the connection, perform either of the following operations. On the smartphone’s Camera Connect screen, tap [t]. On the camera’s [qWi-Fi on] screen, select [Disconnect,exit]. If the [qWi-Fi on] screen is not displayed, select the [54] tab 9 [Communication settings] 9 [Built-in wireless settings] 9 [Wi-Fi function]. Select [Disconnect,exit], then select [OK] on the confirmation dialog to terminate the connection.
Operating the Camera Using a Smartphone When the wireless connection is terminated while recording a movie with remote shooting, the camera responds as follows: • When the Live View shooting/Movie shooting switch is set to , movie shooting continues. • When the Live View shooting/Movie shooting switch is set to , movie shooting stops. When the Live View shooting/Movie shooting switch is set to and the movie mode is set by operating Camera Connect, you cannot shoot by operating the camera.
Sending Images to a Smartphone Operate the camera to send images to a smartphone. The following three send methods are available: (1) While playing back an image, connect to a smartphone using the NFC function. (2) During a wireless connection, select [Send images to smartphone] from the camera menu (p.W-32). (3) During a wireless connection, send images from the Quick Control screen during playback (p.W-34).
Sending Images to a Smartphone a smartphone to the camera. 3 Touch Touch the P mark on the smartphone to that on the camera. If the download site of Camera Connect appears on the smartphone, install Camera Connect (p.W-18). When a message indicating the connection is displayed on the camera’s LCD monitor, move the smartphone away. the images to send. 4 Select Select and send image(s). For information on how to send images, see page W-35.
Sending Images to a Smartphone 3 Select [Built-in wireless settings]. [Send images to 4 Select smartphone]. Select [Send images to smartphone] on the [Built-in wireless settings] screen, then press <0>. the images to send. 5 Select Select and send image(s). For information on how to send images, see page W-35.
Sending Images to a Smartphone (3) Quick Control During Playback While the camera is wirelessly connected to a smartphone, send images from the Quick Control screen during playback. 1 Connect the camera to a smartphone wirelessly. For connection methods, see page W-19. back the image and press 2 Play the button. 3 Select [q]. the images to send. 4 Select Select and send image(s). For information on how to send images, see page W-35.
Sending Images to a Smartphone Sending Images Individually Select and send images individually. 1 Select an image to send. Turn the <5> dial to select an image to send, then press <0>. If you press the button and turn the <6> dial counterclockwise, you can select an image from the index display. [Send img shown]. 2 Select To select a size at which to send the image, select [Resize image] and press <0>. Select [Send img shown] and press <0> to send the image displayed.
Sending Images to a Smartphone the images to send. 3 Select Turn the <5> dial to select an image to send, then add [X]. Press <0> to add or remove [X]. If you press the button and turn the <6> dial counterclockwise, you can select images from a three-image display. After selecting the images to send, press the button. [Resize image]. 4 Select Set it as necessary. On the displayed screen, select an image size, then press <0>. [Send]. 5 Select The selected images will be sent.
Sending Images to a Smartphone Ending Image Transfer To end the image transfer, press the button on the image transfer screen. If you have established the connection with the NFC function while playing back an image, the connection termination screen will appear. Select [OK] to terminate the connection. If you have sent images with the menu or Quick Control, the previous screen will reappear. The connection will not be terminated. If necessary, also read “NFC Function Cautions” (p.W-17).
Specifying Viewable Images You can specify images viewable from a smartphone by operating the camera. Images can be specified during connection setup or after the connection is terminated. 1 Select [Communication settings]. Under the [54] tab, select [Communication settings], then press <0>. 2 Select [Built-in wireless settings]. [Wi-Fi function]. 3 Select Set [Wi-Fi/NFC] to [Enable], then select [Wi-Fi function] (p.W-12).
Specifying Viewable Images [q]. 4 Select If the [qWi-Fi on] screen appears, select [Disconnect,exit]. 5 Select [Review/change settings]. 6 Select [Viewable imgs]. If [Viewable imgs] is set to any setting other than [All images], remote shooting is not possible. When reconnecting to a smartphone, check the settings of viewable images before establishing a connection.
Specifying Viewable Images an item. 7 Select Select [OK] and press <0> to display the setting screen. [All images] All images stored on the card become viewable. [Images from past days] Specify viewable images on the shooting-date basis. Images shot up to nine days ago can be specified. Select an item, then press <0>. When [Images shot in past days] is selected, images shot up to the specified number of days before the current date become viewable.
Specifying Viewable Images [File number range] (Select range) First image Last image Select the first and last images from images arranged by the file number to specify the viewable images. 1 Use <5> or <9> to select the first image file. 2 Press <0> to display the image selection screen. Turn the <5> dial to select an image. If you press the button and turn the <6> dial counterclockwise, you can select an image from the index display. 3 Select an image and press <0> to complete the selection.
Reconnecting The camera can reconnect to a Wi-Fi function for which connection settings is already registered. 1 Select [Communication settings]. Under the [54] tab, select [Communication settings], then press <0>. 2 Select [Built-in wireless settings]. [Wi-Fi function]. 3 Select Set [Wi-Fi/NFC] to [Enable], then select [Wi-Fi function] (p.W-12). the Wi-Fi function to 4 Select connect to. Use <5> or <9> to select an item, then press <0>.
3 Easy Connection to Connect Station Connect Station (sold separately) is a device that allows you to import captured still photos and movies for viewing on your TV set, smartphone, etc., or sharing them over a network. You can easily save still photos and movies to Connect Station by holding this camera close to Connect Station.
Saving Images This section explains how to connect the camera and Connect Station (sold separately) wirelessly. To save images in other ways, refer to the Connect Station Instruction Manual. Set up the camera to allow use of its NFC function in advance (p.W-16). the NFC function on the 1 Enable camera (p.W-16). the camera close to Connect 2 Hold Station. NFC connect point Turn on the camera and Connect Station, then hold the camera’s P mark close to the Connect Station’s NFC connect point.
Saving Images If necessary, also read “NFC Function Cautions” (p.W-17). While saving images, a picture cannot be taken even if the camera’s shutter button is pressed. Do not drop the camera on Connect Station or touch the camera to it with too much force. Doing so may damage Connect Station’s internal hard disk. If the camera is not recognized right away, try holding it close to Connect Station and slowly moving it or rotating it horizontally.
Wi-Fi (Wireless LAN) Precautions 9Countries and Regions Permitting Wireless LAN Use Use of wireless LAN is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating wireless LAN regulations, visit the Canon Web site to check where use is allowed. Note that Canon cannot be held liable for any problems arising from wireless LAN use in other countries and regions.
Hereby, Canon Inc., declares that this DS126601 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Please contact the following address for the original Declaration of Conformity: CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands CANON INC.
Index A Android ...................................... W-18 C Cables........................................ W-14 Camera Connect..............W-18, W-28 Communicating with a smartphone................................ W-19 Connect Station ......................... W-43 E Eye-Fi Card................................ W-14 I iOS............................................. W-18 K Keyboard ................................... W-10 N NFC ........... W-16, W-20, W-21, W-44 Sending images.....................
The descriptions in this Instruction Manual are current as of May 2016. For information on the compatibility with any products introduced after this date, contact any Canon Service Center. For the latest version Instruction Manual, refer to the Canon Web site. CPH-E195-001 © CANON INC.