Basic Instruction Manual This basic manual covers only the most basic operations. For more detailed instructions, refer to the Instruction Manual PDF file on the EOS Camera Instruction Manuals Disk DVD-ROM.
Introduction The EOS 5DS/EOS 5DS R is a digital single-lens reflex camera featuring a full-frame CMOS sensor (approx. 36.0 mm x 24.0 mm) with approx. 50.6 effective megapixels, Dual DIGIC 6, approx. 100% viewfinder coverage, high-precision and high-speed 61-point AF, approx. 5.0 fps continuous shooting, 3.2-inch LCD monitor, Live View shooting, and Full High-Definition (Full HD) movie shooting.
Item Check List Before starting, check that all the following items are included with your camera. If anything is missing, contact your dealer. Eyecup Eg Camera (with body cap) Wide Strap Battery Charger Battery Pack LP-E6N LC-E6/LC-E6E* (with protective cover) Interface Cable IFC-150U II Cable protector * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instruction Manual and DVD/CD-ROMs provided are listed on the next page.
Instruction Manual and DVD/CD-ROMs The instruction manual consists of a booklet, a leaflet, and PDF manuals in electronic form (provided on the DVD-ROM). The booklet is the Basic Instruction Manual. For more detailed instructions, see the Instruction Manual on the DVD-ROM Basic Instruction Manual (this booklet) EOS Camera Instruction Manuals Disk DVD-ROM EOS Camera Instruction Manuals Disk XXX CEL-XXX XXX XXXXX XXXXX XXXXX XXXXX XXXXX © CA . e EU NON IN C. 20XX.
Compatible Cards The camera can use the following cards regardless of capacity: If the card is new or was previously formatted (initialized) by another camera or computer, format the card with this camera (p.59). CF (CompactFlash) cards * Type I, UDMA mode 7-compatible. SD/SDHC*/SDXC* memory cards * UHS-I cards supported. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table. Movie Recording Size (p.
Quick Start Guide 1 Insert the battery (p.34). To charge the battery, see page 32. Insert the card (p.35). 2 The camera-front side slot is for a CF card, and the camera-back side slot is for an SD card. * Shooting is possible with either a CF card or an SD card in the camera. 3 Attach the lens (p.44). 4 Set the lens’s focus mode switch to (p.44). 5 6 Align it with the red dot. Set the power switch to <1> (p.39).
Quick Start Guide 6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto) (p.26). All the necessary camera settings will be set automatically. 7 Focus on the subject (p.47). 8 Take the picture (p.47). 9 Review the picture. Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus on the subject. Press the shutter button completely to take the picture.
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0/9/4/7/8 : : : : : Indicates the Main Dial. Indicates the Quick Control Dial. Indicates the Multi-controller. Indicates the Setting button. Indicates that each function remains active for 4 sec., 6 sec., 8 sec., 10 sec., or 16 sec. after you let go of the button. * In this manual, the icons and markings indicating the camera’s buttons, dials, and settings correspond to the icons and markings on the camera and on the LCD monitor.
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.
Contents Introduction 2 Item Check List................................................................................. 3 Instruction Manual and DVD/CD-ROMs ........................................... 4 Compatible Cards............................................................................. 5 Quick Start Guide ............................................................................. 6 Conventions Used in this Manual..................................................... 8 Chapters.................
Contents Disabling the Beeper ....................................................................61 Setting the Power-off Time/Auto Power Off.................................. 61 Setting the Image Review Time ...................................................62 Reverting the Camera to the Default Settings.............................. 62 l Displaying the Grid. .................................................................. 63 Q Displaying the Electronic Level ..........................................
Contents Setting Crop/aspect ratio................................................................ 99 i: Setting the ISO Speed ......................................................... 101 A Selecting a Picture Style ...................................................... 102 B: Setting the White Balance ................................................... 103 Auto Correction of Brightness and Contrast................................. 104 Setting Noise Reduction ..............................................
Contents 7 Shooting Movies 131 k Shooting Movies .....................................................................132 Autoexposure Shooting ..............................................................132 Shutter-priority AE ......................................................................133 Aperture-priority AE.................................................................... 134 Manual Exposure Shooting ........................................................
Safety Precautions The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Warnings: Follow the warnings below. Otherwise, death or serious injuries may result.
Safety Precautions When the camera or accessories are not in use, make sure to remove the battery and disconnect the power plug from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, or corrosion. Do not use the equipment where there is flammable gas. This is to prevent an explosion or a fire. If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts. There is a possibility of an electrical shock.
Safety Precautions Cautions: Follow the cautions below. Otherwise, physical injury or property damage may result. Do not use or store the product inside a car under the hot sun or near a heat source. The product may become hot and cause skin burns. Doing so may also cause battery leakage or explosion, which will degrade the performance or shorten the life of the product. Do not carry the camera around when it is attached to a tripod. Doing so may cause injury.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth.
Handling Precautions If the camera has not been used for an extended period, test all its functions before using it. If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your nearest Canon Service Center or check the camera yourself and make sure it is working properly. If you use continuous shooting, Live View shooting, or movie shooting for a prolonged period, the camera may become hot. This is not a malfunction.
Nomenclature Drive mode selection/ AF operation/AF method selection button (p.91/76/125) Flash exposure compensation/ISO speed setting button (p.101) LCD panel illumination button (p.51) White balance selection/ Metering mode selection button (p.103/117) AF area selection/ Multi-function button (p.81) Lens mount index (p.44) Flash sync contacts <6> Main Dial (p.48) Hot shoe Mode Dial lock-release button (p.48) Shutter button (p.47) Mode Dial (p.26, 48) Self-timer lamp (p.
Nomenclature LCD panel (p.22-23) Eyecup Viewfinder eyepiece
AF start button (p.47, 76, 123) AE lock button (p.120) AF point selection button (p.81-82) Info button (p.52, 64, 67, 124, 137, 142) Power switch (p.39) Quick Control button (p.53) Menu button (p.56) Terminal cover <5> Quick Control Dial (p.49) Touch pad (p.50) <0> Setting button (p.56) External microphone IN terminal Cable protector socket HDMI mini OUT terminal PC terminal Digital terminal (p.
Nomenclature Dioptric adjustment knob (p.46) Focal plane mark Live View shooting/ Movie shooting switch (p.121/131) <0> Start/Stop button (p.122, 132) Creative Photo/ Comparative playback (Two-image display) button (p.102) <9> Multi-controller (p.50) Rating button Strap mount (p.28) Index/Magnify/ Reduce button (p.148/149) Card slot cover (p.35) Playback button (p.142) Erase button (p.152) Battery compartment cover release lever (p.
Nomenclature LCD Panel Shutter speed FE lock (FEL) Remaining number of exposures for time-lapse movie Busy (buSY) Multi function lock warning (L) No card warning (Card) Error code (Err) Cleaning image sensor (CLn) White balance (p.
Nomenclature HDR shooting Multiple-exposure shooting Bulb timer shooting Interval timer shooting GPS acquisition status Flash exposure compensation Exposure level indicator Exposure compensation amount (p.118) AEB range (p.119) Flash exposure compensation amount AF operation (p.76) X One-Shot AF 9 AI Focus AF Z AI Servo AF 4L Manual focus Drive mode (p.
Nomenclature Viewfinder Information Electronic level (p.64) Spot metering circle (p.117) Focusing screen Aspect ratio line (1:1) Single AF point Spot AF point Grid (p.63) Crop area (1.6x) Area AF frame (p.80) Crop area (1.3x) < > Battery level (p.40) Warning symbol White balance (p.103) Flicker detection (p.110) Drive mode (p.91) AF operation (p.76) JPEG/RAW (p.97) Metering mode (p.117) * The display will show only the settings currently applied.
Nomenclature ISO speed (p.101) Focus indicator (p.70, 77) AE lock (p.120) AEB in-progress (p.119) Flash-ready Improper FE lock warning AF status indicator (p.70) Maximum burst Number of remaining multiple exposures ISO speed (p.101) Highlight tone priority (p.107) FE lock FEB in-progress High-speed sync Flash exposure compensation Shutter speed (p.
Nomenclature Mode Dial You can set the shooting mode. Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). F : Bulb a : Manual exposure (p.115) f : Aperture-priority AE (p.114) s : Shutter-priority AE (p.113) d : Program AE (p.112) A : Scene Intelligent Auto (p.70) Custom shooting mode You can register the shooting mode (d/s/f/a/F), AF operation, menu settings, etc., to w, x, y Mode Dial positions.
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6N/LP-E6 (p.32). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. Battery Charger LC-E6E Charger for Battery Pack LP-E6N/LP-E6 (p.32).
Nomenclature Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap.
Nomenclature Using the Cable Protector When connecting the camera to a computer, printer, Wireless File Transmitter or GPS Receiver, use the provided interface cable or one from Canon. When connecting the interface cable, also use the provided cable protector. Using the cable protector prevents the cable from accidental disconnection and the terminal from getting damaged.
Nomenclature Using a Genuine Interface Cable (sold separately) If you use a genuine interface cable (sold separately), run the cable through the clamp before attaching the clamp to the cable protector. Clamp Connecting interface cable without using the cable protector may damage the digital terminal. Do not use a USB 2.0 cable equipped with a Micro-B plug. It may damage the camera’s digital terminal.
1 Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations.
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully-charged Battery Pack LP-E6N (or LP-E6) into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. the cover. 3 Close Press the cover until it snaps shut.
Installing and Removing the Card The camera can use a CF card and an SD card. Images can be recorded when at least one card is installed in the camera. If both types of card are inserted, you can select which card to record images to, or simultaneously record images on both cards (p.94-96). Cautions for Using an SD Card If you use an SD card, be sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 CF card SD card Write-protect switch Open the cover.
Installing and Removing the Card the cover. 3 Close Close the cover and slide it in the Possible Card selection icon shots direction shown by the arrows until it snaps shut. X When you set the power switch to <1> (p.39), the number of possible shots and the loaded card(s) will be displayed on the LCD panel. The images will be recorded to the card indicated by the arrow < > icon. CF card indicator SD card indicator The camera cannot use Type II CF cards, hard disk-type cards, or CFast cards.
Installing and Removing the Card Removing the Card 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed on the LCD monitor, close the cover. Access lamp the card. 2 Remove To remove the CF card, push the CF card eject button eject button. To remove the SD card, push it in gently and release it. Then pull it out. Pull the card straight out, then close the cover.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to, read from, or erased from the card, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 41 to set the date/time/zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera. Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, sensor cleaning will be executed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Battery Level Indicator When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon indicates that the battery will be exhausted soon. Display Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 9-1 0 Number of Possible Shots Temperature Room Temperature (23°C / 73°F) Low Temperatures (0°C / 32°F) Possible shots Approx. 700 shots Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone are reset, the date/time/zone setting screen will appear. Follow the steps below, making sure to set the time zone first. Set the camera to the time zone in which you currently live so that, when you travel, you can simply change the setting to the correct time zone for your destination and the camera will automatically adjust the date/time.
3 Setting the Date, Time, and Zone the date and time. 4 SetTurn the <5> dial to select the number. Press <0> so is displayed. Turn the <5> dial to select the desired setting, then press <0> (Returns to ). saving time. 5 SetSettheit ifdaylight necessary. Turn the <5> dial to select [Y]. Press <0> so is displayed. Turn the <5> dial to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 4 will advance by 1 hr.
3 Selecting the Interface Language The date/time that were set will start from when you select [OK] in step 6. In step 3, the time displayed on the upper right of the screen is the time difference compared with Coordinated Universal Time (UTC). If you do not see your time zone, set the time zone while referring to the difference with UTC. 3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK].
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S or EF-M lenses. Attaching a Lens 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the red dots on the lens and camera and turn the lens as shown by the arrow until it clicks in place. the lens’s focus mode switch 3 Set to . stands for autofocus. stands for manual focus. Autofocus will not operate.
Attaching and Detaching a Lens Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrow. Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens. Do not look at the sun directly through any lens. Doing so may cause loss of vision. When attaching or detaching a lens, set the camera’s power switch to <2>. If the front part (focusing ring) of the lens rotates during autofocusing, do not touch the rotating part.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup. If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using Dioptric Adjustment Lens Eg (sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake. Horizontal shooting Vertical shooting 1.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing Halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel for 4 sec. (metering timer/0). Pressing Completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Use it to set the shooting mode. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for 6 sec. (9). During this time, you can turn the <6> dial to change the setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for 6 sec. (9). During this time, you can turn the <5> dial to change the setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select the white balance, drive mode, flash exposure compensation, AF point, etc. (2) Turn the <5> dial only.
Basic Operation 9 Multi-controller The <9> consists of an eight-direction key and a button at the center. Use your thumb to tilt the <9> in the desired direction. Use it to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, operate the Quick Control screen, etc. You can also use it to select and set menu items.
Basic Operation R Multi Function Lock By setting [83: Multi function lock] and moving the switch to the right, you can prevent the Main Dial, Quick Control Dial, and Multi-controller from moving and changing a setting inadvertently. switch set to the left: Lock released switch set to the right: Lock engaged If the switch is set to the right and you try to operate any of the locked camera controls, will appear in the viewfinder and on the LCD panel.
Basic Operation Displaying Quick Control Screen After you press the button a number of times, the Quick Control screen (p.54) or Custom Quick Control screen will appear. You can then check the current shooting function settings. Pressing the button enables Quick Control of the shooting function settings (p.53). Then you can press the button to turn off the screen.
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control. The basic operating procedures are the same for the Quick Control screen (p.52) and the Custom Quick Control screen (p.54). 1 Press the button (7). X The Quick Control screen will appear. the desired functions. 2 SetUse <9> to select a function. X The setting of the selected function is displayed. Turn the <5> or <6> dial to change the setting.
Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen Aperture (p.114) Shutter speed (p.113) AE lock* (p.120) Highlight tone priority* (p.107) Shooting mode* (p.26) Exposure compensation/ AEB setting (p.118/119) Picture Style (p.102) AF operation (p.76) ISO speed (p.101) Flash exposure compensation Custom Controls Image-recording quality (p.97) White balance (p.103) Metering mode (p.
Q Quick Control for Shooting Functions Quick Control Screen Ð <0> Select a function and press <0>. The function setting screen will appear. Turn the <6> or <5> dial to change some of the settings. There are also functions that are set by pressing the button. Press <0> to finalize the setting and return to the previous screen.
3 Menu Operations You can set various settings with the menus such as the image-recording quality, date/time, etc. button <6> Main Dial LCD monitor <5> Quick Control Dial button <0> button A Mode Menu Screen * Certain menu tabs and menu items are not displayed in the mode.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Each time you press the button, the main tab will switch. Turn the <6> dial to select a secondary tab. For example, the [z5] tab refers to the screen displayed when the z (Shooting) tab’s fifth dot “ ” from the left is selected. the desired item. 3 Select Turn the <5> dial to select the item, then press <0>. the setting.
3 Menu Operations The explanation of menu functions hereinafter assumes that you have pressed the button to display the menu screen. You can also use <9> to operate and set menu functions. (Except for [31: Erase images] and [51: Format card].) To cancel the operation, press the button. Dimmed Menu Items Example: When Multi Shot Noise Reduction is set Dimmed menu items cannot be set. The menu item is dimmed if another function setting is overriding it.
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with this camera. Cautions for Formatting the Card When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card].
Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed. Low-level Formatting Perform low-level formatting if the SD card’s reading or writing speed seems slow or if you want to totally erase all data on the card. Since low-level formatting will erase all recordable sectors on the SD card, the formatting will take longer than normal formatting.
Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved or during self-timer operation. 1 Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. [Disable]. 2 Select Select [Disable], then press <0>. X The beeper will not sound. 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. The default setting is 1 min., but this setting can be changed.
Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor just after shooting. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. 1 Select [Image review]. Under the [z1] tab, select [Image review], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>. If [Hold] is set, the image will be displayed until the auto power off time elapses.
l Displaying the Grid You can display a grid in the viewfinder to help you check the camera tilt or compose the shot. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Grid display]. [Show]. 3 Select X When you exit the menu, the grid will appear in the viewfinder.
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help you correct camera tilt. Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level. If the electronic level does not appear, set [53: z button display options] so that the electronic level can be displayed. the camera’s tilt.
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder An electronic level can be displayed on the upper part of the viewfinder. Since this can be displayed while you shoot, you can correct the camera tilt while shooting. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Electronic level]. 3 Select [Show]. the shutter button halfway. 4 Press X The electronic level will be displayed in the viewfinder.
3 Setting the Viewfinder Information DisplayN The shooting function settings (Battery, White balance, Drive mode, AF operation, Metering mode, Image quality: JPEG/RAW, Flicker detection) can be displayed in the viewfinder. By default, only Flicker detection is checkmarked [X]. 1 Select [Viewfinder display]. Under the [52] tab, select [Viewfinder display], then press <0>. 2 Select [Show/hide in viewfinder]. [X] the information to 3 Checkmark be displayed.
Help When [z Help] is displayed at the bottom of the menu screen, the feature’s description (Help) can be displayed. The Help screen is displayed only while you hold down the button. If the Help fills more than one screen, a scroll bar will appear on the right edge. To scroll, hold down the button and turn the <5> dial.
2 Basic Shooting This chapter explains how to use the Mode Dial’s (Scene Intelligent Auto) mode for easy picture taking. In the mode, all you do is point and shoot and the camera sets everything automatically. Also, to prevent botched pictures due to mistaken operations, advanced shooting function settings cannot be changed. Scene Intelligent Auto Auto Lighting Optimizer In the mode, the Auto Lighting Optimizer (p.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.73). 1 Area AF frame Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. the Area AF frame over the 2 Aim subject. All the AF points will be used to focus, and the camera will focus on the closest object.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. X The captured image will be displayed for 2 sec. on the LCD monitor. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If you did not obtain the desired color tones, change the mode to , , , or , set a Picture Style other than , then shoot again (p.102). FAQ The focus indicator blinks and focus is not achieved.
A Fully Automatic Shooting (Scene Intelligent Auto) Pressing the shutter button halfway does not focus on the subject. If the focus mode switch on the lens is set to (manual focus), set it to (autofocus). The shutter speed display is blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (sold separately) is recommended.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, pressing the shutter button halfway to focus on a still subject will lock the focus on that subject. Recompose the shot while keeping the shutter button pressed halfway, and then press the shutter button completely to take the picture. This is called “focus lock”.
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 121. 1 Set the Live View shooting/Movie shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. X The Live View image will appear on the LCD monitor. on the subject. 3 Focus Press the shutter button halfway to focus.
3 Setting the AF and Drive Modes The AF points in the viewfinder are arranged to make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF operation and drive mode that best match the shooting conditions and subject. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . In the mode, the AF operation and AF area selection mode are set automatically. stands for autofocus.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In the mode, “AI Focus AF” is set automatically. 1 Set the lens’s focus mode switch to . the 2 Set mode. 3 Press the button. (9) the AF operation. 4 Select While looking at the LCD panel or in the viewfinder, turn the <6> dial.
f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus indicator in the viewfinder will also light up. With evaluative metering (p.117), the AF point Focus indicator exposure setting will be set at the same time as focus is achieved. While you hold down the shutter button halfway, the focus will be locked.
f: Selecting the AF OperationN AI Focus AF for Switching the AF Operation Automatically AI Focus AF switches the AF operation from One-Shot AF to AI Servo AF automatically if a still subject starts moving. After the subject is focused in One-Shot AF, if the subject starts moving, the camera will detect the movement, change the AF operation automatically to AI Servo AF, and start tracking the moving subject.
S Selecting the AF Area and AF PointN The camera has 61 AF points for autofocusing. You can select the AF area selection mode and AF point(s) suiting the scene or subject. Depending on the lens attached to the camera, the number of usable AF points and AF point patterns will differ. For details, see “Lenses and Usable AF Points” on page 84. AF Area Selection Mode You can select one of six AF area selection modes. For the setting procedure, see page 81.
S Selecting the AF Area and AF PointN AF point expansion (Manual selection, surrounding points) The manually-selected AF point and the surrounding AF points are used to focus. Zone AF (Manual selection of zone) One of nine zones is used to focus. 61-point automatic selection AF The Area AF frame (entire AF area) is used to focus. This mode is set automatically in the mode.
S Selecting the AF Area and AF PointN Selecting the AF Area Selection Mode 1 Press the button. (9) the button. 2 Press Look through the viewfinder and press the button. Each time you press the button, the AF area selection mode changes.
S Selecting the AF Area and AF PointN Selecting the AF Point Manually You can manually select the AF point or zone. 1 Press the button. (9) X The AF points will be displayed in the viewfinder. In AF point expansion modes, adjacent AF points will also be displayed. In the Zone AF mode, the selected zone will be displayed. an AF point. 2 Select The AF point selection will change in the direction you tilt <9>. If you press <9> straight down, the center AF point (or center zone) will be selected.
AF Sensor The camera’s AF sensor has 61 AF points. The illustration below shows the AF sensor pattern corresponding to each AF point. With f/2.8 or larger maximum aperture lenses, high-precision AF is possible at the viewfinder center. Depending on the lens attached to the camera, the number of usable AF points and AF pattern will differ. For details, see pages 84-88. Diagram Cross-type focusing: f/4 horizontal + f/5.6 vertical Cross-type focusing: f/5.6 vertical + f/5.6 horizontal f/5.
Lenses and Usable AF Points Although the camera has 61 AF points, the number of usable AF points and focusing patterns will differ depending on the lens. The lenses are thereby classified into nine groups from A to I. When using a lens in Groups F to H, fewer AF points will be usable. To see which group a lens belongs to, refer to “Instruction Manual” (PDF file, p.154) on the EOS Camera Instruction Manuals Disk DVDROM. When you press the button, the AF points indicated by the mark will blink.
Lenses and Usable AF Points Group B Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Dual cross-type AF point. Subject tracking is superior and the focusing precision is higher than with other AF points. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group C Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Cross-type AF point.
Lenses and Usable AF Points Group D Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Dual cross-type AF point. Subject tracking is superior and the focusing precision is higher than with other AF points. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. Group E Autofocusing with 61 points is possible. All the AF area selection modes are selectable. : Cross-type AF point.
Lenses and Usable AF Points Group F Autofocusing with only 47 points is possible. (Not possible with all 61 AF points.) All the AF area selection modes are selectable. During automatic AF point selection, the outer frame marking the AF area (Area AF frame) will be different from 61-point automatic selection AF. : Cross-type AF point. Subject tracking is superior and highprecision focusing is achieved. : AF points sensitive to horizontal lines. : Disabled AF points (not displayed).
Lenses and Usable AF Points Group H AF is possible with the center AF point and the adjacent AF points above, below, on the left, and on the right. Only the following AF area selection modes are selectable: Single-point AF (manual selection), Single-point Spot AF (manual selection), and AF point expansion (manual selection ). If an Extender is attached to the lens and the maximum aperture is f/8 (between f/5.6 and f/8), AF will be possible. : Cross-type AF point.
3 Selecting AI Servo AF CharacteristicsN You can easily fine-tune AI Servo AF to suit a particular subject or shooting scene just by selecting an option from case 1 to case 6. This feature is called the “AF Configuration Tool.” 1 Select the [21] tab. a case. 2 Select Turn the <5> dial to select a case icon, then press <0>. X The selected case will be set. The selected case is indicated in blue.
MF: Manual Focus 1 Set the lens’s focus mode switch to . X <4 L> will be displayed on the LCD panel. Focusing ring on the subject. 2 Focus Focus by turning the lens’s focusing ring until the subject looks sharp in the viewfinder.
o Selecting the Drive Mode Single and continuous drive modes are provided. You can select the drive mode suiting the scene or subject. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. o: High-speed continuous shooting While you hold down the shutter button completely, the camera will shoot continuously at a maximum of approx. 5.
j Using the Self-timer Use the self-timer when you want to be in the picture. 1 Press the button. (9) the self-timer. 2 Select While looking at the LCD panel or in the viewfinder, turn the <5> dial. Q : 10-sec. self-timer k : 2-sec. self-timer picture. 3 TakeLookthethrough the viewfinder, focus on the subject, then press the shutter button completely. X You can check the self-timer operation with the self-timer lamp, beeper, and countdown display (in seconds) on the LCD panel. X 2 sec.
4 Image Settings This chapter explains image-related function settings: Image-recording quality, Crop/aspect, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, noise reduction, highlight tone priority, lens aberration correction, anti-flicker shooting, and other functions. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: .
3 Selecting the Card for Recording and Playback If either a CF card or SD card is already inserted in the camera, you can start recording captured images. When only one card is inserted, you do not have to follow the procedures described on pages 94-96. If you insert both a CF card and SD card, you can select the recording method and select which card to use for recording and playing back images. [f] indicates the CF card, and [g] the SD card.
3 Selecting the Card for Recording and Playback Standard Images will be recorded to the card selected with [Record/play]. Auto switch card Same as with the [Standard] setting, but if the card becomes full, the camera will automatically switch to the other card to record images. When the card is automatically switched, a new folder will be created. Rec. separately You can set the image-recording quality for each card (p.97).
3 Selecting the Card for Recording and Playback Selecting the CF or SD Card for Recording and Playback If [Record func.] is set to [Standard] or [Auto switch card], select the card for recording and playing back images. If [Record func.] is set to [Rec. separately] or [Rec. to multiple], select the card for playing back images. Standard / Auto switch card Select [Record/play]. Select [Record/play], then press <0>. f : Record images to and play images back from the CF card.
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are ten JPEG image-recording quality settings: 73, 83, 7K, 8K, 75, 85, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61. 1 Standard / Auto switch card / Rec. to multiple Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording quality. 2 Select To select a RAW quality, turn the <6> dial. To select a JPEG quality, turn the <5> dial.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Image Quality 73 83 7K 8K JPEG 75 Pixels Recorded Print Size 50M A1 39M 14.1 510 31 (510) 7.0 1030 1030 (1030) 10.9 660 45 (660) 5.5 1310 1310 (1310) 1010 1010 (1010) 2030 2030 (2030) 4.5 1590 1590 (1590) 2.3 3120 3120 (3120) 9x13 cm 1.2 5600 5600 (5600) - 0.3 20380 20380 (20380) 12M A3 b*1 2.5M c*2 0.3M 1 8a Maximum Burst 7.1 A2 7a Possible Shots 3.
Setting Crop/Aspect RatioN Normally, images are recorded at the sensor size of approx. 36.0 mm x 24.0 mm (full-frame shooting). You can record only the center of the image magnified approx. 1.3x (equivalent to APS-H size) or approx. 1.6x (equivalent to APS-C size) as if you were using a telephoto lens (crop shooting) or set the desired aspect ratio before you shoot. 1 Select [Crop/aspect ratio]. Under the [z4] tab, select [Crop/ aspect ratio], then press <0>. the desired setting.
Setting Crop/Aspect RatioN Example settings With e•b the picture. 4 Take Viewfinder shooting The shooting area in the viewfinder will be masked or have frame lines. The area surrounded by the semitransparent masking or frame lines will be recorded as an image. With f•c With d With g•b 100 Live View shooting When [1.3x (crop)] or [1.6x (crop)] is set, the displayed image will be magnified by approx. 1.3x or 1.6x respectively.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. With the mode selected, the ISO speed will be set automatically. 1 Press the button. (9) the ISO speed. 2 SetWhile looking at the LCD panel or in the viewfinder, turn the <6> dial. ISO speed can be set within ISO 100 - ISO 6400 in 1/3-stop increments. “A” indicates Auto ISO. The ISO speed will be set automatically.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. The Picture Style is set automatically to [D] (Auto) in the mode. 1 Press the button. [A]. 2 Select X The Picture Style selection screen will appear. a Picture Style. 3 Select X The Picture Style will be set and the camera will be ready to shoot.
B: Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the Auto [Q] (Ambience priority) or [Qw] (White priority) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with Auto, you can select the white balance to match the light source or set it manually by shooting a white object. is automatically set in the [Q] (Ambience priority) mode. 1 Press the button. (9) a white balance setting.
3 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. [Standard] is automatically set in the mode. 1 Select [Auto Lighting Optimizer]. Under the [z2] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced. 1 Select [High ISO speed NR]. Under the [z3] tab, select [High ISO speed NR], then press <0>. the level. 2 SetSelect the desired noise reduction level, then press <0>.
3 Setting Noise ReductionN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z3] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetSelect the desired setting, then press <0>. Auto For exposures of 1 sec. or longer, noise reduction is performed automatically if noise typical of long exposures is detected. This [Auto] setting is effective in most cases.
3 Highlight Tone PriorityN You can reduce overexposed, clipped highlights. 1 Select [Highlight tone priority]. Under the [z3] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. picture. 3 TakeThetheimage will be recorded with highlight tone priority applied.
3 Correction of Lens Peripheral Illumination and Aberration Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. This lens aberration and light fall-off can be corrected. By default, Peripheral illumination and Chromatic aberration correction are set to [Enable]. Peripheral Illumination Correction 1 Select [Lens aberration correction].
3 Correction of Lens Peripheral Illumination and Aberration Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. picture. 2 TakeThetheimage will be recorded with the chromatic aberration corrected. Lens Correction Data The camera already contains data for lens peripheral illumination correction and chromatic aberration correction for approx.
3 Reducing FlickerN If you shoot an image with a fast shutter speed under a light source such as fluorescent light, the blinking of the light source causes flicker and the image may be vertically unevenly exposed. If continuous shooting is used under these conditions, uneven exposures or colors across the images may result. With anti-flicker shooting, the camera detects the frequency of the light source’s blinking and takes the picture when the flicker causes less effect on exposure or color.
5 Advanced Operations In the shooting modes, you can select the shutter speed, aperture, and other camera settings to change the exposure and obtain the desired result. A M icon at the upper right of a page title indicates a function that can be used only in the following modes: . After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the LCD panel for 4 sec. (0). Set the switch to the left.
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . on the subject. 2 Focus Look through the viewfinder and aim the AF point over the subject. Then press the shutter button halfway. X When focus is achieved, the focus indicator in the viewfinder will light up (in One-Shot AF mode).
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure matching the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action of a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen action (Fast shutter speed: 1/2000 sec.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. Shutter speed Aperture 1 Set the Mode Dial to . 2 Set the ISO speed (p.101). speed and aperture. 3 SetTothesetshutter the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
a: Manual Exposure Exposure Compensation with Auto ISO If the ISO speed is set to A (AUTO), you can set exposure compensation (p.118) as follows: • [z2: Expo.comp./AEB] • Under [83: Custom Controls], use [s: Expo comp (hold btn, turn )]. • Quick Control (p.
q Selecting the Metering ModeN You can select one of four methods to measure the subject brightness. In the mode, evaluative metering is set automatically. 1 Press the button. (9) the metering mode. 2 Select While looking at the LCD panel or in the viewfinder, turn the <6> dial.
O Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the , , and shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3-stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z2] tab, select [Expo.comp./AEB], then press <0>. the AEB range. 2 SetTurn the <6> dial to set the AEB AEB range range. If you turn <5>, you can set the exposure compensation. Press <0> to set it.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the picture. This is called AE lock. It is effective for backlit subjects, etc. 1 Focus on the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
6 Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images. Using a tripod is recommended.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. X The Live View image will appear on the LCD monitor. The Live View image will closely match the brightness level of the actual image you capture. on the subject. 3 Focus When you press the shutter button halfway, the camera will focus with the current AF method (p.125). the picture. 4 TakePress the shutter button completely.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [z5: Live View shoot.] (the [z3] tab in ) to [Enable]. Number of Possible Shots with Live View Shooting Temperature Room Temperature (23°C / 73°F) Low Temperatures (0°C / 32°F) Possible shots Approx. 220 shots Approx. 210 shots The figures above are based on a fully-charged Battery Pack LP-E6N and CIPA (Camera & Imaging Products Association) testing standards.
A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change.
Shooting Function Settings Crop/Aspect You can perform crop shooting, or shoot with the set aspect ratio for Live View shooting. To set them with the menu, see page 99. If you use [83: Custom Controls] to assign [Switch between crop/aspect] to the button, you can just press the button while displaying Live View image to switch the Crop/aspect setting. Using AF to Focus (AF Method) Selecting the AF Method You can set the AF method to [u(face)+Tracking] (p.126) or [FlexiZone - Single] (p.
Using AF to Focus (AF Method) u(face)+Tracking: c The camera detects and focuses on human faces. If a face moves, the AF point
also moves to track the face. 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. an AF point. 2 Select When a face is detected, the
frame will appear over the face to be focused on. If multiple faces are detected, will be displayed. Use <9> to move the frame over the face you want to focus on.
Using AF to Focus (AF Method) Focusing on a subject other than a human face Press <9> or <0> and the AF frame < > will appear in the center. Then use <9> to move the AF frame over the desired subject. Once the AF frame < > achieves focus, it will track the subject even if the subject moves or if you change the composition.
Using AF to Focus (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus on a particular subject. the Live View image. 1 Display Press the <0> button. X The Live View image will appear on the LCD monitor. X The AF point < > will appear. AF point the AF point. 2 Move Use <9> to move the AF point to where you want to focus. (It cannot be moved to the edge of the screen.
MF: Focusing Manually You can magnify the image and focus precisely with MF (manual focus). 1 Set the lens’s focus mode switch to . Turn the lens’s focusing ring to focus roughly. the magnifying frame. 2 Display Press the button. X The magnifying frame will appear. Magnifying frame the magnifying frame. 3 Move Use <9> to move the magnifying frame to the position where you want to focus. Pressing <9>, <0>, or button will return the magnifying frame to the screen’s center. the image.
MF: Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens’s focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 TakeCheck the exposure, then press the shutter button completely to take the picture (p.122).
7 Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . For cards that can record movies, see page 5. If you handhold the camera and shoot movies, camera shake can cause blurred movies. Using a tripod is recommended. Full HD 1080 Full HD 1080 indicates compatibility with HighDefinition featuring 1080 vertical pixels (scanning lines).
k Shooting Movies / Autoexposure Shooting When the shooting mode is set to , , or , autoexposure control will take effect to suit the scene’s current brightness. Exposure control will be the same for all the shooting modes. the Mode Dial to , , 1 Set or . the Live View shooting/Movie 2 Set shooting switch to . X The reflex mirror will make a sound, then the image will appear on the LCD monitor. on the subject. 3 Focus Before shooting a movie, focus with AF or manual focus (p.
k Shooting Movies Shutter-priority AE When the shooting mode is , you can manually set the shutter speed for movie shooting. The ISO speed and aperture will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired shutter speed. 3 SetWhile looking at the LCD monitor, Shutter speed turn the <6> dial. The settable shutter speeds depend on the frame rate. • 6 5 4: 1/4000 sec.
k Shooting Movies Aperture-priority AE When the shooting mode is , you can manually set the aperture for movie shooting. The ISO speed and shutter speed will be set automatically to suit the brightness and obtain a standard exposure. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the desired aperture. 3 SetWhile looking at the LCD monitor, turn the <6> dial. Aperture and shoot the movie.
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. For details on the ISO speed, see the next page. the shutter speed and 4 Set aperture.
k Shooting Movies and shoot the movie. 5 Focus The procedure is the same as steps 3 and 4 for “Autoexposure Shooting” (p.132). ISO Speed in the Mode With [Auto] (A), the ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z2: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [H (12800)], the automatic ISO range will not expand to the H maximum.
k Shooting Movies Information Display Each time you press the button, the information display will change.
3 Setting the Movie Recording Size With [z4: Movie rec. size] (the [z2] tab in ), you can set the movie’s image size, frame rate (frames per sec.), and compression method. The frame rate displayed on the [Movie rec. size] screen switches automatically depending on the [53: Video system] setting. Image Size L 1920x1080 Full High-Definition (Full HD) recording quality. The aspect ratio is 16:9. w 1280x720 High-Definition (HD) recording quality. The aspect ratio is 16:9.
3 Setting the Movie Recording Size Compression Method W ALL-I (For editing/I-only) Compresses one frame at a time for recording. Although the file size is larger than with IPB (Standard), the movie is more suited for editing. X IPB (Standard) Compresses multiple frames at a time efficiently for recording. Since the file size is smaller than with ALL-I (For editing), you can shoot longer (with a card of the same capacity). Total Movie Recording Time and File Size Per Minute (Approx.
3 Setting the Movie Recording Size Movie Files Exceeding 4 GB Even if you shoot a movie exceeding 4 GB, you can keep shooting without interruption. During movie shooting, approx. 30 sec. before the movie reaches the 4 GB file size, the elapsed shooting time or time code displayed in the movie-shooting screen will start blinking. If you keep shooting until the movie file size exceeds 4 GB, a new movie file will be created automatically and the elapsed shooting time or time code will stop blinking.
8 Image Playback This chapter explains basic procedures to play back images and movies. Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. X The last image captured or played back will appear. an image. 2 Select To play back images starting with the last image captured, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the information display will change.
x Image Playback the image playback. 3 ExitPress the button to exit the image playback and return to shooting-ready state. Shooting Information Display With the shooting information screen displayed (p.142), you can tilt <9> up or down to change the shooting information displayed at the screen’s bottom as follows. For details, see pages 145-146.
B: Shooting Information Display Sample Information for Still Photos Basic information display Eye-Fi transfer completed Eye-Fi card transmission status Battery level Rating Protect images Card Folder number File number Playback number/ Total images recorded Shutter speed Image-recording quality/Edited images/Cropping Aperture Highlight tone priority Exposure compensation amount ISO speed If the image was taken by another camera, certain shooting information may not be displayed.
B: Shooting Information Display Shooting information display • Detailed information Exposure compensation amount Aperture Histogram (Brightness/RGB) Shooting date and time Shutter speed ISO speed Shooting mode/ Multiple exposure Scroll bar Highlight tone priority White balance Metering mode File size Auto Lighting Optimizer White balance correction/ Correction amount AF Microadjustment Flash exposure compensation amount/HDR shooting/ Multi Shot Noise Reduction Crop Image-recording quality/ Edited
B: Shooting Information Display • Lens/Histogram information Histogram display (Brightness) Lens name Histogram display (RGB) Focal length • White balance information • Picture Style information 1 • Picture Style information 2 • Color space / Noise reduction information • Lens aberration correction information 146
B: Shooting Information Display Sample Movie Information Display Movie playback Aperture Shutter speed ISO speed Movie shooting mode/ Time-lapse movie File size Movie recording size Frame rate Recording time/Time code Compression method • < > and < > modes: Shutter speed, aperture and ISO speed are not displayed. • < > mode: Aperture and ISO speed are not displayed. • < > mode: Shutter speed and ISO speed are not displayed. • < > mode + Auto ISO: ISO speed is not displayed.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) You can search for images quickly with the index display showing 4, 9, 36, or 100 images on one screen. 1 Press the button. During image playback or when the camera is ready to shoot, press the button. X [6u] will be displayed on the lower right of the screen. to the index display. 2 Switch Turn the <6> dial counterclockwise. X The 4-image index display will appear.
u Magnifying Images You can magnify a captured image by approx. 1.5x to 16x on the LCD monitor. 1 Magnified area position Magnify the image. The image can be magnified as follows: 1. During image playback (single-image display), 2. During the image review after image capture, and 3. From the shooting-ready state. Press the button. X The magnified view will appear. The magnified area and [6u] will be displayed on the lower right of the screen.
k Playing Back Movies 1 Play back the image. Press the button to display an image. a movie. 2 Select Turn the <5> dial to select the movie to be played. With the single-image display, the icon displayed on the upper left indicates a movie. In the index display, perforations at the left edge of a thumbnail indicate a movie. As movies cannot be played from the index display, press <0> to switch to the single-image display. the single-image display, press 3 In<0>.
k Playing Back Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by turning the <5> dial. The slow motion speed is indicated on the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie.
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button. 2 Press X The Erase menu will appear.
9 Viewing the DVD-ROM Instruction Manuals / Downloading Images to Your Computer This chapter explains how to view the Camera and Software Instruction Manuals (on the DVD-ROM provided) on your computer, download images from the camera to your computer, gives an overview of the software in the EOS Solution Disk (CD-ROM), and explains how to install the software on your computer.
Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) EOS Camera Instruction Manuals Disk XXX The EOS Camera Instruction Manuals Disk (DVD-ROM) contains the following electronic manuals (PDF). CEL-XXX XXX XXXXX XXXXX XXXXX XXXXX XXXXX © CA . e EU NON IN C. 20XX. Made in th Instruction Manual Explains all the camera functions and procedures, including basic content. Software Instruction Manuals Software Instruction Manuals PDFs for the software supplied on the EOS Solution Disk (see p.159).
Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) [WINDOWS] EOS Camera Instruction Manuals Disk XXX CEL-XXX XXX XXXXX XXXXX XXXXX XXXXX XXXXX © CA . e EU NON IN C. 20XX. Made in th EOS Camera Instruction Manuals Disk Copy the PDF Instruction Manuals contained on the disk to your computer. 1 Insert the EOS Camera Instruction Manuals Disk (DVD) into the DVD-ROM drive of your computer.
Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) Viewing the EOS Camera Instruction Manuals Disk (DVD-ROM) [MACINTOSH] EOS Camera Instruction Manuals Disk XXX CEL-XXX XXX XXXXX XXXXX XXXXX XXXXX XXXXX © CA . e EU NON IN C. 20XX. Made in th EOS Camera Instruction Manuals Disk Copy the PDF Instruction Manuals contained on the disk to your computer. 1 Insert the EOS Camera Instruction Manuals Disk (DVD) into the DVD-ROM drive of your Macintosh. 2 3 4 Double-click on the disk icon.
Downloading Images to a Computer You can use the EOS software to download the images in the camera to your computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer 1 Install the software (p.159). the provided interface cable 2 Use to connect the camera to your computer. Use the interface cable provided with the camera. When connecting the cable to the camera, use the cable protector (p.29).
Downloading Images to a Computer Downloading Images with a Card Reader You can also use a card reader to download images to your computer. Install the software (p.159). 1 the card into the card 2 Insert reader. Digital Photo Professional to 3 Use download the images. For details, refer to the Digital Photo Professional Instruction Manual (p.154). When downloading images from the camera to your computer with a card reader without using EOS software, copy the DCIM folder on the card to your computer.
About the Software EOS Solution Disk XXX XXXXX XXXXX XXXXX XXXXX XXXXX EOS Solution Disk This disk contains various software for EOS cameras. CEL-XXX XXX Windows XXX XXX Mac OS X XXX XXX © CA U. the E NON INC . 20XX. Made in Note that the software provided with previous cameras might not support still photos and movie files shot with this camera. Please use the software provided with this camera.
Installing the Software Installing the Software on Windows Compatible OS Windows 8.1 1 Windows 8 Windows 7 Check that the camera is not connected to your computer. Do not connect the camera to your computer before you install the software. The software will not be installed correctly. If a previous version is installed, follow the steps below to reinstall the software. (The newer version will overwrite the previous version.) 2 Insert the EOS Solution Disk (CD).
Installing the Software Installing the Software on Macintosh Compatible OS 1 MAC OS X 10.8 - 10.10 Check that the camera is not connected to your computer. Do not connect the camera to your computer before you install the software. The software will not be installed correctly. If a previous version is installed, follow the steps below to reinstall the software. (The newer version will overwrite the previous version.) 2 Insert the EOS Solution Disk (CD).
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Only for European Union and EEA (Norway, Iceland and Liechtenstein) These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives.
CANON INC. 30-2 Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan Europe, Africa & Middle East CANON EUROPA N.V. PO Box 2262, 1180 EG Amstelveen, The Netherlands For your local Canon office, please refer to your warranty card or to www.canon-europe.com/Support The product and associated warranty are provided in European countries by Canon Europa N.V. The descriptions in this Instruction Manual are current as of March 2015.
