EOS 6D (WG) EOS 6D (N) PY O C The EOS 6D (N) does not have the Wi-Fi and GPS functions explained in this manual. Basic Instruction Manual This basic manual covers only the most basic operations. For other features and more details, see the Camera Instruction Manual pdf file in the CD-ROM.
Introduction The EOS 6D (WG/N) is high-performance, digital single-lens reflex camera featuring a full-frame (approx. 35.8 x 23.9 mm) CMOS sensor with approx. 20.2 effective megapixels, DIGIC 5+, high-precision and high-speed 11-point AF, approx. 4.5 fps continuous shooting, Live View shooting, Full High-Definition (Full HD) movie shooting, Wi-Fi*, and GPS*.
Compatible Cards The camera can use the following cards regardless of capacity: • SD memory cards • SDHC memory cards* • SDXC memory cards* * UHS-I cards compatible. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table. Compression Method (p.116) Card IPB 6 MB/sec. or faster ALL-I (I-only) 20 MB/sec. or faster If you use a slow-writing card when shooting movies, the movie may not be recorded properly.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Camera (with body cap) Wide Strap EW-EOS6D Battery Pack LP-E6 (with protective cover) Interface Cable IFC-200U C Y OP Battery Charger LC-E6/LC-E6E* Stereo AV Cable AVC-DC400ST * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instruction Manuals and CD-ROMs provided are listed on the next page.
Instruction Manuals and CD-ROMs The instruction manuals are provided in both paper and electronic (PDF) forms. Camera Basic Instruction Manual (this booklet) Wi-Fi (Basic)/ GPS Function Instruction Manual* Wi-Fi/GPS Cautions* Pocket Guide * Not provided with the EOS 6D (N). PY O C The Basic Instruction Manual explains the basic procedures and features. For detailed instructions, see the Camera Instruction Manual CD-ROM.
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0, 9, 7, 8 : Indicates the Main Dial. : Indicates the Quick Control Dial. : Indicates the Multi-controller and the push direction. : Indicates the Setting button. : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec. respectively after you let go of the button.
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.
Contents Introduction 2 Compatible Cards............................................................................. 3 Item Check List................................................................................. 4 Instruction Manuals and CD-ROMs.................................................. 5 Conventions Used in this Manual ..................................................... 6 Chapters...........................................................................................
Contents Q Displaying the Electronic Level ............................................... 53 Feature Guide and Help.................................................................. 54 2 Basic Shooting 57 A Fully Automatic Shooting (Scene Intelligent Auto) ................... 58 A Full Auto Techniques (Scene Intelligent Auto) ......................... 61 C Creative Auto Shooting............................................................. 63 8: Special Scene Mode ......................................
Contents 4 Image Settings 83 Setting the Image-Recording Quality ............................................. 84 i: Setting the ISO Speed ........................................................... 86 A Selecting a Picture Style ........................................................ 87 Setting the White Balance .............................................................. 88 Auto Correction of Brightness and Contrast ................................... 89 Noise Reduction Settings ...................
Contents 8 Image Playback 119 x Image Playback ...................................................................... 120 H Searching for Images Quickly ................................................. 121 u Magnified View ........................................................................ 122 k Playing Movies........................................................................ 123 L Erasing Images ........................................................................
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there may be a few dead pixels displaying only black or red, etc. among the remaining 0.01% or less pixels. Dead pixels are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Quick Start Guide 1 2 Insert the battery (p.26). To charge the battery, see page 24. Insert a card (p.27). With the card’s label facing toward the back of the camera, insert it into the card slot. 3 Attach the lens (p.35). 4 Set the lens focus mode switch to (p.35). 5 14 Align it with the red dot. PY O C Set the power switch to <1> (p.30). When the LCD monitor displays the date/time/zone setting screens, see page 32.
Quick Start Guide 6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto) (p.58). All the necessary camera settings will be set automatically. 7 8 9 Focus the subject (p.40). Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus the subject. PY Press the shutter button completely O C to take the picture. Take the picture (p.40). Review the picture (p.51).
Nomenclature LCD panel (p.18) Drive mode selection button (p.81) AF operation selection button (p.78) ISO speed setting button (p.86) Metering mode selection button Lens mount index (p.35) Flash-sync contacts LCD panel illumination button (p.44) Hot shoe <6> Main Dial (p.41) Mode Dial lock release button (p.41) Mode Dial (p.20) Shutter button (p.40) Strap mount (p.23) Self-timer lamp (p.82) C Remote control sensor Y OP Speaker (p.123) Microphone Lens release button (p.
Nomenclature
AF start button (p.40, 105) Focal plane mark Live View shooting/ Movie shooting switch (p.103/113) <0> Start/Stop button (p.104, 114) AE lock/ FE lock button (p.101) Dioptric adjustment knob (p.39) AF point selection button (p.79) Eyecup Viewfinder eyepiece Quick Control button (p.45) Strap mount (p.23) Power switch (p.30) Menu button (p.47) Card slot cover (p.27) Info button (p.44, 53, 55, 120) PY O C Battery compartment cover release lever (p.
Nomenclature LCD Panel Drive mode (p.81) u Single shooting i Continuous shooting B Silent single shooting M Silent continuous shooting Q Self-timer: 10 sec./ Remote control k Self-timer: 2 sec./ Remote control Highlight tone priority (p.92) ISO speed (p.86) ISO speed (p.86) Possible shots Self-timer countdown Bulb exposure time Error No. Remaining images to record AEB AF operation (p.
Nomenclature Viewfinder Information AF points (p.79) (Superimposed display) Focusing screen Spot metering circle ISO speed (p.86) Warning symbol Battery check (p.31) AE lock (p.101) / AEB in-progress Flash-ready Improper FE lock warning FE lock/ FEB in-progress High-speed sync Flash exposure compensation Shutter speed (p.97) FE lock (FEL) Busy (buSY) Multi function lock warning (L) C Y OP Focus confirmation light (p.59) Max.
Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). Creative Zone These modes give you more control for shooting various subjects. d : Program AE (p.96) s : Shutter-priority AE (p.97) f : Aperture-priority AE (p.98) a : Manual exposure (p.99) F : Bulb Basic Zone Custom shooting mode You can register the shooting mode (d/s/f/a/F), AF operation, menu settings, etc., to the w or x Mode Dial setting and shoot.
Nomenclature Lens EF24-105mm f/4L IS USM Focus mode switch (p.35) Distance scale Infrared index Hood mount (p.37) Zoom ring (p.36) Zoom position index (p.36) φ77mm filter thread (front of lens) Focusing ring (p.80, 111) Contacts (p.13) Image Stabilizer switch (p.38) PY O C Lens mount index (p.
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.24). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. PY O C Battery Charger LC-E6E Charger for Battery Pack LP-E6 (p.24).
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Y P O Attaching the Strap C Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap.
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Recharge the battery before using. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully charged Battery Pack LP-E6 into the camera. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. the cover. 3 Close Ycover until it snaps shut. PressP the O C Only Battery Pack LP-E6 can be used. Removing the Battery Open the cover and remove the battery.
Installing and Removing the Card The camera can use an SD, SDHC, or SDXC memory card. UHS-I Speed Class SDHC and SDXC memory cards can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 Write-protect switch Open the cover. Slide the cover as shown by the arrows to open it. the card.
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent you from forgetting to insert a card. Removing the Card 1 Access lamp Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed, close the cover. the card. 2 Remove Gently push Pit.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to or read by the card, being erased, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Turning on the Power If you turn on the power switch and the Date/Time/Zone setting screen appears, see page 32 to set the Date/Time/Zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera. About the Automatic Self-Cleaning Sensor Whenever you set the power switch to <1> or <2>, sensor cleaning will be executed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Icon Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 Number of Possible Shots 9-1 0 [Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the Date/Time/Zone setting screens will appear. Follow the steps below to set the time zone first. If you set the camera to the correct time zone for where you currently live, when you travel to another time zone you can simply set the camera to the correct time zone for your destination to update the camera’s date/time automatically.
3 Setting the Date, Time, and Zone the date and time. 4 SetPress the key to select the number. Press <0> so is displayed. Press the key to set the number, then press <0>. (Returns to .) Saving Time. 5 SetSettheit ifDaylight necessary. Press the key to select [Y]. Press <0> so is displayed. Press the key to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 4 will advance by 1 hour.
3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK]. Press the key to select the [52] tab. Press the key to select [LanguageK], then press <0>. PY O C the desired language. 3 SetPress the key to select the language, then press <0>. X The interface language will change.
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S and EF-M lenses. 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the red dots on the lens and camera and turn the lens as shown by the arrow until it clicks in place. the lens focus mode switch to 3 Set . PYstands for Autofocus. O If it is set to (manual focus), C autofocus will not operate.
Attaching and Detaching a Lens About Zooming To zoom, turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus slightly. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrows. Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens.
Attaching and Detaching a Lens Attaching a Lens Hood A lens hood can block unwanted light and protect the front of the lens from rain, snow, dust, etc. Before storing the lens in a bag, etc., you can attach the hood in reverse. If the Lens Hood and Lens Have a Mount Index 1 Align the red dots on the hood and lens edges, and turn the hood as shown by the arrow. the hood as shown in the 2 Turn illustration. Turn the hood clockwise until it attaches securely.
About the Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF24-105mm f/4L IS USM lens as an example. * IS stands for Image Stabilizer. 1 Set the Image Stabilizer switch to <1>. Also set the camera’s power switch to <1>. the shutter button halfway. 2 Press X The Image Stabilizer will operate. the picture.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup. If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (10 types, sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0). Pressing completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <6> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select or set the AF operation, drive mode, ISO speed, metering mode, AF point selection, etc.
Basic Operation 9 Multi-controller The Multi-controller <9> has eight keys which tilt in the directions shown by the arrows. Use the eight keys to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, etc. For menus and the Quick Control, the Multi-controller works only in the vertical and horizontal directions . It does not work in diagonal directions. PY O With [8C.
Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed. With the shooting settings displayed, you can turn the Mode Dial to see the settings for each shooting mode.
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called the Quick Control screen. 1 Press the button. X The Quick Control screen will appear (7). the desired function. 2 SetPress the key to select a function. X The setting of the selected function is displayed. Turn the <6> or <5> dial to change the setting. Basic Zone modes Creative PY Zone modes O C the picture.
Q Quick Control for Shooting Functions Sample Quick Control Screen Aperture (p.98) Shutter speed (p.97) Shooting mode*1 (p.20) Flash exposure compensation AE lock*1 (p.101) Highlight tone priority*1 (p.92) Exposure compensation/AEB setting (p.100) Wi-Fi function*2 Picture Style (p.87) Custom Controls ISO speed (p.86) AF operation (p.78) White balance (p.88) AF point (p.79) White balance correction Drive mode (p.81) Image-recording quality (p.84) Auto Lighting Optimizer (p.
3 Menu Operations You can set various settings with the menus such as the imagerecording quality, date/time, etc. While looking at the LCD monitor, use the button, keys, and <0> button on the camera back. button <0> button LCD monitor Menus in Basic Zone Modes PY O C * Some menu tabs and menu items are not displayed in Basic Zone modes.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Press the key to select a menu tab. For example, the [z4] tab refers to the screen displayed when the forth tab from the left [ ] is selected. the desired item. 3 Select Press the key to select the item, then press <0>. 4 PY O C Select the setting. Press the or key to select the desired setting.
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data in the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card]. Under the [51] tab, select [Format card], then press <0>. PYthe card.
Before You Start Execute [Format card] in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed. About Low-level Formatting Perform low-level formatting if the card’s recording or reading speed seems slow or if you want to totally erase data in the card. Since low-level formatting will format all recordable sectors in the card, the formatting will take slightly longer than normal formatting.
Before You Start 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. If you do not want the camera to turn off automatically, set this to [Disable]. After the power turns off, you can turn on the camera again by pressing the shutter button or other buttons. 1 Select [Auto power off]. Under the [52] tab, select [Auto power off], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>.
Before You Start 3 Turning the LCD Monitor Off/On The shooting settings display (p.44) can be set to remain on even when you press the shutter button halfway. Under the [52] tab, select [LCD off/on btn], then press <0>. The available settings are described below. Select one, then press <0>. [Remains on] : Display remains on even when you press the shutter button halfway. To turn off display, press the button. [Shutter btn.] : When you press the shutter button halfway, the display will turn off.
Q Displaying the Electronic Level Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level. If the electronic level does not appear, set [53: z button display options] so that the electronic level can be displayed. the camera’s tilt. 2 Check The Y horizontal tilt is displayed in 1° P increments. O When C the red line turns green, it indicates that the tilt is corrected.
Feature Guide and Help While you set some function, the feature’s description can be displayed. Feature Guide The Feature guide displays a simple description of the respective shooting mode, function or option. It appears when you change the shooting mode or set a shooting function, Live View shooting, Movie shooting, or Quick Control for playback. When you select a function or option on the Quick Control screen, the Feature guide description appears.
Feature Guide and Help Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge. You can turn the <5> dial to scroll down. Example: [z4: Long exp. noise reduction] B Î Scroll bar PY O C Example: [8C.Fn I -1: Exposure level increments] B Î Example: [8C.
PY O C
Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. PY O C ic Z on e With Basic Zone modes, all you do is point and shoot while the camera sets everything automatically (p.75). Also, to prevent botched pictures due to mistaken operations, the main shooting function settings cannot be changed.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.61). 1 AF point Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. any AF point over the 2 Aim subject. All the AF points will be used to focus, and generally the closest object will be focused.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. X The captured image will be displayed for 2 sec. on the LCD monitor. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If the desired color tone is not obtained, use a Creative Zone mode and select a Picture Style other than and shoot (p.87). FAQ The focus confirmation light blinks and focus is not achieved.
A Fully Automatic Shooting (Scene Intelligent Auto) The shutter speed display is blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (sold separately) is recommended. When the external flash was used, the bottom part of the picture came out unnaturally dark. If a hood is attached to the lens, it can obstruct the flash coverage. If the subject is close, detach the hood before taking the picture with flash.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, while you press the shutter button halfway to focus a still subject, the focus will be locked. You can then recompose the shot and press the shutter button completely to take the picture. This is called “focus lock”. Focus lock is also possible in other Basic Zone modes (except <5> Sports).
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 103. 1 Set the Live View shooting/Movie shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. X The Live View image will appear on the LCD monitor. theYsubject. 3 Focus P center AF point < Aim the O Csubject. > on the Press the shutter button halfway to focus.
C Creative Auto Shooting In the mode, you can easily change the depth of field and drive mode. You can also choose the ambience you want to convey in your images. The default settings are the same as the mode. * CA stands for Creative Auto. 1 Set the Mode Dial to . the button. (7) 2 Press X The Quick Control screen will appear. the desired function. 3 SetPress the key to select a function. Y Pselected function and Feature XO The C guide (p.54) will appear.
C Creative Auto Shooting (1) Shutter speed Aperture ISO speed (2) (3) Battery check Image-recording quality Possible shots Pressing the button enables you to set the following: PY O C (1) Ambience-based shots You can choose the ambience you want to convey in your images. Turn the <6> or <5> dial to select the desired ambience. You can also select it from a list by pressing <0>.
C Creative Auto Shooting (3) Drive mode: Press the key to select the desired drive mode. You can also select the drive mode by turning the <6> or <5> dial, or pressing <0> to select it from a list. Single shooting: Shoot one image at a time. Continuous shooting: While you hold down the shutter button completely, shots will be taken continuously. You can shoot up to approx. 4.5 shots per second. Silent single shooting: Single shooting with less shooting sound than .
8: Special Scene Mode When you set a shooting mode suiting the scene, the camera sets the optimum settings automatically. 1 Set the Mode Dial to <8>. the button. (7) 2 Press X The Quick Control screen will appear. the shooting mode. 3 Select Press the key to select the shooting mode section. Turn the <6> or <5> dial to select a shooting mode. PY O C You can also select a shooting mode from a list by selecting the shooting mode section and pressing <0>.
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and the hair look softer. PY O The further the distance between C the subject and background, Shooting Tips the better. The further the distance between the subject and background, the more blurred the background will look. The subject will also stand out better in front of a plain, dark background. Use a telephoto lens.
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips PY O C With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end. It also adds breadth to landscapes. Shooting night scenes. When shooting night scenes, use a tripod to prevent camera shake.
4 Shooting Close-ups When you want to photograph flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips PY O C Use a simple background. A simple background makes the flower, etc., stand out better. Move as close as possible to the subject. Check the lens for its minimum focusing distance. Some lenses have indications such as <40.25m/0.8ft>.
5 Shooting Moving Subjects To photograph a moving subject, whether it is a child running or a moving vehicle, use the <5> (Sports) mode. Shooting Tips PY O C Use a telephoto lens. Using a telephoto lens is recommended so you can shoot from afar. Use the center AF point to focus. Aim the center AF point over the subject, then press the shutter button halfway to autofocus. During autofocusing, the beeper will continue beeping softly. If focus cannot be achieved, the focus confirmation light will blink.
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Flash is required. Using a tripod is also recommended. PY O C and a tripod. Use a wide-angle lens, Speedlite, Shooting Tips When using a zoom lens, use the wide-angle end to obtain a wide night view. Also, use a tripod to prevent camera shake. Also shoot in another shooting modes.
F Shooting Night Scenes (Handheld) Normally, a tripod is necessary to steady your camera when shooting a night scene. However, with the (Handheld Night Scene) mode, you can shoot night scenes while handholding the camera. In this mode, four shots are taken continuously for each picture, and a resulting bright image with reduced camera shake is recorded. Shooting Tips PY O C Hold the camera firmly. While shooting, hold the camera firmly and steadily.
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the (HDR Backlight Control) mode. When you take a picture, three continuous shots are taken at different exposures, and the resulting image with the least loss of shadow detail due to backlighting and widest tonal range is recorded. Shooting Tips PY O C Hold the camera firmly. While shooting, hold the camera firmly and steadily. If any of the three shots are greatly misaligned due to camera shake, etc.
Cautions for (Handheld Night Scene) During Live View shooting, it may be difficult to focus dots of light such as in a night scene. In such a case, you should set the AF method to [Quick mode] and shoot. If it is still difficult to focus, set the lens’ focus mode switch to [MF] and focus manually. When shooting flash photography, if the subject is too close to the camera, the picture may come out extremely bright (overexposure).
Q Quick Control In Basic Zone modes when the shooting function settings screen is displayed, you can press the button to display the Quick Control screen. The table below indicates the functions that can be set with the Quick Control screen in each Basic Zone mode. Example: Portrait mode 1 Set the Mode Dial to a Basic Zone mode. 2Press the button. (7) X The Quick Control screen will appear. 3 Set the function. Press the key to select a function. (This step is not necessary in the A mode.
PY O C
Setting the AF and Drive Modes The viewfinder has 11 AF points. By selecting the optimum AF point, you can compose the picture as desired while autofocusing. PY O C You can also select the AF operation and drive mode that best match the shooting conditions and subject. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). In Basic Zone modes, the AF operation and AF point are set automatically. stands for autofocus.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. 1 Set the lens focus mode switch to . the Mode Dial to a Creative 2 Turn Zone mode. 3 Press the button. (9) the AF operation. 4 Select Y WhileP looking at the LCD panel, turn theO <6> or <5> dial.
S Selecting AF PointsN You can select an AF point for focusing from among eleven AF points. In Basic Zone modes, the AF point will be selected automatically and you cannot select the AF point. 1 Press the button. (9) X The selected AF point will be displayed in the viewfinder and on the LCD panel. When all the AF points light up, automatic AF point selection will be set. an AF point. 2 Select You can either use <9> or turn the <6> or <5> dial to select an AF point.
MF: Manual Focusing 1 Set the lens focus mode switch to . X <4 L> will be displayed on the LCD panel. Focusing ring the subject. 2 Focus Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder.
i Selecting the Drive Mode Single and continuous drive modes are provided. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel, turn the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. i : Continuous shooting (Max. approx. 4.5 shots/sec.) While you hold down the shutter button completely, shots will be taken continuously. B : Silent single shooting Single shooting with less shooting sound than .
j Using the Self-timer Use the self-timer when you want to be in the picture. 1 Press the button. (9) the self-timer. 2 Select While looking at the LCD panel, turn the <6> or <5> dial to select the self-timer delay. Q : 10-sec. self-timer k : 2-sec. self-timer picture. 3 TakeLookthethrough the viewfinder, focus the subject, then press the shutter button completely. X You can check the self-timer operation with the self-timer lamp, beeper, and countdown display (in seconds) on the LCD panel.
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. PY O C The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61. 1 Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording quality. 2 Select To select a RAW setting, turn the <6> dial. To select a JPEG setting, press the key.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Image Quality 73 83 74 JPEG 84 7a Pixels File Size Possible Printing Size Recorded (MB) Shots 20M A2 8.9M A3 Maximum Burst 6.0 1250 73 (1250) 3.1 2380 2380 (2380) 3.2 2300 2300 (2300) 1.7 4240 4240 (4240) 2.1 3450 3450 (3450) 1.1 6370 6370 (6370) 5.0M A4 b*1 2.5M 9x13 cm 1.2 6130 6130 (6130) c*2 0.3M - 0.3 23070 23070 (23070) 1 14 (17) 8a 20M A2 23.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically. 1 Press the button. (9) the ISO speed. 2 SetWhile looking at the LCD panel or the viewfinder, turn the <6> or <5> dial. ISO speed can be set within ISO 100 - 25600 in 1/3-stop increments. “A” indicates ISO Auto. The ISO speed will be set automatically. You can also press the button to set it to “A (AUTO)”.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, (Auto) is set automatically. 1 Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>. X The Picture Style selection screen will appear. a Picture Style. 2 Select Press the key to select a Picture Style, then press <0>. X The Picture Style will be set and the camera will be ready to shoot.
3 Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the (Auto) setting will obtain the correct white balance. If naturallooking colors cannot be obtained with , you can select the white balance to match the light source or set it manually by shooting a white object. In Basic Zone modes, is set automatically. 1 Select [White balance]. Under the [z3] tab, select [White balance], then press <0>. the white balance.
3 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically. 1 Select [Auto Lighting Optimizer]. Under the [z3] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Noise Reduction SettingsN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced. 1 Select [High ISO speed NR]. Under the [z4] tab, select [High ISO speed NR], then press <0>. the level. 2 SetSelect the desired noise reduction level, then press <0>.
3 Noise Reduction SettingsN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z4] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetSelect the desired setting, then press <0>. X The setting screen closes and the menu will reappear. PY O C [Auto] For 1 sec. or longer exposures, noise reduction is performed automatically if noise typical of long exposures is detected.
3 Highlight Tone PriorityN You can minimize overexposed highlight areas. 1 Select [Highlight tone priority]. Under the [z4] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. Y Ppicture. the O 3 Take CThe image will be recorded with highlight tone priority applied.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. Both lens aberrations can be corrected. The default settings are [Enable] for both corrections. Peripheral Illumination Correction 1 Select [Lens aberration correction]. Under the [z2] tab, select [Lens aberration correction], then press <0>. the setting.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “About the Lens Correction Data” below. picture. 2 TakeThetheimage will be recorded with the chromatic aberration corrected.
Advanced Operations In Creative Zone modes, you can set the shutter speed and/or aperture to set the exposure as desired. By changing the camera settings, you can obtain various results. PY O C The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the LCD panel for 4 sec. (0). Set the switch to the left.
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . the subject. 2 Focus Look through the viewfinder and aim the selected AF point over the subject. Then press the shutter button halfway.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen action (Fast shutter speed: 1/2000 sec.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . 2 Set the ISO speed (p.86). the shutter speed and 3 Set aperture. To set the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
Setting Exposure Compensation N Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the shot. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
PY O C
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to .
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. X The Live View image will appear on the LCD monitor. The Live View image will closely reflect the brightness level of the actual image you capture. the subject. 3 Focus When you press the shutter button halfway,Y the camera will focus with P the current AF method (p.106). O C the picture. 4 TakePress the shutter button completely.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [A1: Live View shoot.] to [Enable]. Number of Possible Shots with Live View Shooting [Approx. number of shots] Temperature Room Temperature ( 23°C / 73°F) Low Temperature (0°C / 32°F) Possible shots 220 190 The figures above are based on a fully-charged Battery Pack LP-E6 and CIPA (Camera & Imaging Products Association) testing standards. With a fully-charged Battery Pack LP-E6, continuous Live View shooting is possible for approx.
Using AF to Focus (AF Method) Selecting the AF Method The AF methods available are [FlexiZoneAF (Single)], [u Live mode] (face detection, p.107), and [Quick mode] (p.109). If you want to achieve precise focus, set the lens focus mode switch to , magnify the image, and focus manually (p.111). Select the AF method. Under the [A1] tab, select [AF method]. While the Live View image is displayed, you can also press the button to select the AF method on the setting screen.
Using AF to Focus (AF Method) the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. X When focus is achieved, the AF point will turn green and the beeper will sound. X If focus is not achieved, the AF point will turn orange. the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.104). PY O This is the same AF method as Cwith FlexiZone - Single.
Using AF to Focus (AF Method) the subject. 2 Focus Press the shutter button halfway and the camera will focus the face covered by the
frame. X When focus is achieved, the AF point will turn green and the beeper will sound. X If focus is not achieved, the AF point will turn orange. If a face cannot be detected, the AF point < > will be displayed and AF will be executed at the center. the picture. 3 TakeCheck the focus and exposure, then press the shutter button completely to take the PYpicture (p.104).
Using AF to Focus (AF Method) Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode, using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation. You can use eleven AF points to focus (automatically selected). You can also select one AF point to focus and focus only the area covered by that AF point (manually selected).
Using AF to Focus (AF Method) the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. X The Live View image will turn off, the reflex mirror will go back down, and AF will be executed. (No picture is taken.) X When focus is achieved, the beeper will sound and the Live View image will reappear. X The AF point used to focus will light up in green. X If focus is not achieved, the AF point will blink in orange. the picture.
Focusing Manually You can magnify the image and focus precisely with manual focus. 1 Set the lens focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame. 2 Display Press the button. Magnifying frame the magnifying frame. Y<9> 3 Move P Press to move the magnifying to the position where you want COframe to focus. To return the magnifying frame to the center, press <0> or the button. the image.
Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.104).
Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . The movie recording format will be MOV. PY O C For cards which can record movies, see page 3. Under the [53] tab, if you set [Wi-Fi] to [Enable], you cannot shoot movies. Before shooting movies, set [Wi-Fi] to [Disable].
k Shooting Movies Autoexposure Shooting When the shooting mode is set to other than , autoexposure control will take effect to suit the scene’s current brightness. 1 Set the shooting mode. Set the Mode Dial to any shooting mode except . the Live View shooting/Movie 2 Set shooting switch to . X The reflex mirror will make a sound, then the image will appear on the LCD monitor. the subject. 3 Focus Before shooting a movie, focus with AF or manual PyouY pressfocusthe(p.106-112).
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. PY O 4C Set the shutter speed and aperture.
3 Setting the Movie-Recording Size With [Z2: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9. B [1280x720] : High-Definition (HD) recording quality. The aspect ratio will be 16:9. C [640x480] : Standard-definition recording quality. The aspect ratio will be 4:3.
3 Setting the Movie-Recording Size Total Movie Recording Time and File Size Per Minute MovieRecording Size A 65 4 X Total Recording Time (approx.) 4 GB Card 8 GB Card 16 GB Card File Size (approx.) 16 min. 32 min. 1 hr. 4 min. 235 MB/min. 11 min. 22 min. 685 MB/min. 65 4 W 5 min. 87 B 87 C 65 X W X 18 min. 6 min. 48 min. 37 min. 1 hr. 14 min. 12 min. 25 min. 1 hr. 37 min. 3 hr. 14 min. 205 MB/min. 610 MB/min. 78 MB/min.
PY O C
Image Playback This chapter explains basic procedures to play back images and movies. PY O C About images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. X The last captured image or last image viewed will appear. an image. 2 Select To play back images starting with the last image, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the display format will change.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing four or nine images on one screen. 1 Press the button. Press the button during image playback. X [6u] will be displayed on the lower right of the screen. to the index display. 2 Switch Turn the <6> dial counterclockwise. X The 4-image index display will appear. The selected image is highlighted in a orange frame.
u Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. 1 Magnified area position Magnify the image. The image can be magnified during image playback (single-image display), during image review after image capture, and from shootingready state. Press the button. X The magnified view will appear. The magnified area and [6u] will be displayed on the lower right of the screen. The image magnification increases as you turn the <6> dial clockwise.
k Playing Movies 1 Play back the image. Press the button to display images. a movie. 2 Select Turn the <5> dial to select the movie to be played. On the single-image display, the icon displayed on the upper left indicates a movie. If the movie is a video snapshot, < > will be displayed. You can press the button to switch to the shooting information display. In the index display, perforations at the left edge of a thumbnail indicate a movie.
k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by pressing the key. The slow-motion speed is indicated at the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie. 6 Next frame Each time you press <0>, the movie will play frame-byframe.
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button.
PY O C
Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer This chapter explains how to install the Camera Instruction Manual (on the CD-ROM provided) to your computer, download images from the camera to your computer, gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on your computer. It also explains how to view the PDF files on the Software Instruction Manual CD-ROM.
Viewing the Camera Instruction Manual CD-ROM The Camera Instruction Manual CD-ROM contains the following electronic manuals (PDF): Camera Instruction Manual Explains all the camera functions and procedures, including basic content (this booklet). Wi-Fi Function Instruction Manual Explains all the Wi-Fi functions and procedures, including basic content. Viewing the Camera Instruction Manual on the CD-ROM To view the instruction manuals (PDF files), Adobe Reader 6.
Viewing the Camera Instruction Manual CD-ROM the START file. 3 Double-click X The screen shown in step 4 will appear. The icon displayed will differ depending on your computer’s operating system. on the manual you want to view. 4 Click Click on the name of the manual under your respective language. PY O C X The instruction manual in your language will be displayed. You can save the PDF file to your computer.
Downloading Images to a Computer You can use the provided software to download the images in the camera to your computer. There are two ways to do this. Download by Connecting the Camera to the Computer 1 Install the software (p.134). the provided interface cable 2 Use to connect the camera to your computer. Use the interface cable provided with the camera. Connect the cable to the camera’s terminal with the cable plug’s icon facing the front of the camera.
Downloading Images to a Computer Downloading Images with a Card Reader If you have a commercially-available card reader, you can use it to download images to your computer. Install the software (p.134). 1 the card into the card 2 Insert reader. Y software to download 3 Use PCanon the images/movies. O CX Use Digital Photo Professional. X Use ImageBrowser EX. For details, refer to the Software Instruction Manual on the CD-ROM (p.135).
About the Software EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely with the computer connected to the camera. Also, you can copy background music tracks, such as EOS Sample Music*, to the card.
About the Software Picture Style Editor You can edit Picture Styles and create and save original Picture Style files. This software is aimed at advanced users who are experienced in processing images. Map Utility With the GPS position information, you can display where the picture was taken on a map on your computer. To install Map Utility, an Internet connection is required. Access the Internet, insert EOS DIGITAL Solution Disk into your computer, then click [Easy Installation] ([Install] for Macintosh).
Installing the Software Do not connect the camera to your computer before you install the software. The software will not be installed correctly. Even if your computer already has ImageBrowser EX installed, install ImageBrowser EX included on the CD-ROM that came with this camera. It is the latest version with features optimized for your camera. You can also use the auto update feature to add the latest functions.
Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Instruction Manual PDFs 1 Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. 2 Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. 3 Copy the [English] folder to your computer. Instruction Manual PDFs with the names below are copied. EOS Utility Digital Photo Professional PY O C Windows Macintosh EUx.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Macintosh and Mac OS are trademarks or registered trademarks of Apple Inc. in the United States and other countries. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Use of genuine Canon accessories is recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
Digital Camera Model DS126401 / DS126402 / DS126403 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS — This manual contains important safety and operating instructions for Battery Charger LC-E6 & LC-E6E. 2. Before using the charger, read all instructions and cautionary remarks on (1) the charger, (2) the battery pack, and (3) the product using the battery pack. 3. CAUTION — To reduce risk of injury, charge only the Battery Pack LP-E6. Other types of batteries may burst, causing personal injury and other damage. 4.
MEMO PY O C 142
MEMO PY O C 143
MEMO PY O C 144
MEMO PY O C 145
MEMO PY O C 146
MEMO PY O C 147
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. http://www.usa.canon.com/eos http://www.usa.canon.com/support For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.