EOS 70D (W) EOS 70D (N) C Y P O E The EOS 70D (N) does not have the Wi-Fi function explained in this manual.
Introduction The EOS 70D (W/N) is a high-performance, digital single-lens reflex camera featuring a fine-detail CMOS sensor with approx. 20.2 effective megapixels, DIGIC 5+, high-precision and high-speed 19-point AF (all cross-type focusing), approx. 7.0 fps continuous shooting, Live View shooting, Full High-Definition (Full HD) movie shooting, and Wi-Fi function*.
Compatible Cards The camera can use the following cards regardless of capacity: • SD memory cards • SDHC memory cards* • SDXC memory cards* * UHS-I cards supported. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table. Compression Method (p.265) Card IPB 6 MB/sec. or faster ALL-I (I-only) 20 MB/sec. or faster If you use a slow-writing card when shooting movies, the movie may not be recorded properly.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Battery Pack LP-E6 (with protective cover) Camera (with body cap) Wide Strap EW-EOS70D C Battery Charger LC-E6/LC-E6E* Y P O Interface Cable * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instruction Manuals and CD-ROMs provided are listed on the next page.
Instruction Manual and CD-ROMs The instruction manual consists of booklets and electronic manuals (PDF files on the CD-ROM). Basic operations are explained in the booklets. For detailed instructions on all functions and operations, see the detailed version manuals on the CD-ROM. Camera Basic Instruction Manual Quick Reference Guide Wi-Fi Function Instruction Manual* (Basic) Y P O Wi-Fi Cautions* * Not provided with the EOS 70D (N).
Quick Start Guide Insert the battery (p.30). 1 To charge the battery, see page 28. Insert a card (p.31). 2 3 4 5 With the card’s label facing toward the back of the camera, insert it into the card slot. White index Red index Y P O Attach the lens (p.40). C Align the lens’ white or red mount index with the camera’s mount index of the same color. Set the lens focus mode switch to (p.40). Set the power switch to <1>, then set the Mode Dial to (Scene Intelligent Auto) (p.72).
Quick Start Guide 6 Flip out the LCD monitor (p.34). 7 Focus the subject (p.45). 8 9 When the LCD monitor displays the date/time/zone setting screens, see page 37. Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway. The camera will focus the subject. If necessary, the built-in flash will be raised. Y P O Take the picture (p.45). C Press the shutter button completely to take the picture. Review the picture (p.60).
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0, 9, 7, 8 : Indicates the Main Dial. : Indicates the Quick Control Dial. : Indicates the Multi-controller and the push direction. : Indicates the Setting button. : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec. respectively after you let go of the button.
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.
Contents Introduction 2 Compatible Cards............................................................................. 3 Item Check List................................................................................. 4 Instruction Manual and CD-ROMs ................................................... 5 Quick Start Guide ............................................................................. 6 Conventions Used in this Manual ..................................................... 8 Chapters............
Contents 2 Basic Shooting 71 A Fully Automatic Shooting (Scene Intelligent Auto) ................... 72 A Full Auto Techniques (Scene Intelligent Auto) ......................... 75 7 Disabling Flash ......................................................................... 77 C Creative Auto Shooting............................................................. 78 8: Special Scene Mode ............................................................. 81 2 Shooting Portraits ...................................
Contents Setting the White Balance ............................................................ 134 O Custom White Balance........................................................ 135 P Setting the Color Temperature ............................................ 137 White Balance Correction............................................................. 138 Auto Correction of Brightness and Contrast ................................. 140 Setting Noise Reduction.....................................................
Contents 6 Flash Photography 187 D Using the Built-in Flash ............................................................. 188 D Using an External Speedlite...................................................... 193 Setting the Flash ........................................................................... 195 Using Wireless Flash .................................................................... 203 7 Shooting with the LCD Monitor (Live View Shooting) 215 A Shooting with the LCD Monitor ...........
Contents Setting Ratings ............................................................................. 302 Q Quick Control for Playback ..................................................... 304 k Enjoying Movies ..................................................................... 306 k Playing Movies ....................................................................... 308 X Editing a Movie’s First and Last Scenes ................................. 310 Slide Show (Auto Playback) .........................
Contents Custom Function Settings............................................................. 365 C.Fn I: Exposure ........................................................................ 365 C.Fn II: Autofocus ...................................................................... 368 C.Fn III: Operation/Others .......................................................... 375 8: Fine Adjustment of AF’s Point of Focus ................................. 377 8: Custom Controls ...................................
Index to Features Power Charging the battery Battery check Battery information check Household power outlet Auto power off Î p.28 Î p.36 Î p.396 Î p.400 Î p.59 Card Formatting Release shutter without card Î p.57 Î p.32 Lens Attaching/Detaching Zoom Image Stabilizer Î p.40 Î p.41 Î p.43 Basic Settings Language Date/Time/Zone Beeper Copyright information Clear all camera settings Viewfinder Dioptric adjustment Eyepiece cover Electronic level (During shooting) Electronic level (Before shooting) Î p.
Index to Features Remote control Quick Control Î p.184 Î p.50 Exposure Adjustment Exposure compensation AEB AE lock Safety shift Î p.167 Î p.168 Î p.170 Î p.367 Flash Built-in flash External flash Flash function settings Wireless shooting Î p.188 Î p.193 Î p.195 Î p.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth.
Handling Precautions If the camera has not been used for an extended period, test all its functions before using it. If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your Canon dealer or check the camera yourself and make sure it is working properly. If you use continuous shooting, Live View shooting, or movie shooting for a prolonged period, the camera may become hot. This is not a malfunction.
Nomenclature LCD panel (p.22) Drive mode selection button (p.111) AF mode selection button (p.100) ISO speed setting button (p.120) EF lens mount index (p.40) Metering mode selection button (p.165) Built-in flash/AF-assist beam (p.188/203) EF-S lens mount index (p.40) AF area selection mode button (p.104) Flash sync contacts Hot shoe (p.193) Flash button (p.188) <6> Main Dial (p.46) Microphone (p.269) LCD panel illumination button (p.
Nomenclature Focal plane mark AF start button (p.45, 100, 217, 259) Live View shooting/ Movie shooting switch (p.215/251) <0> Start/Stop button (p.216, 252) AE lock/FE lock button/ Index/Reduce button (p.170, 192/296, 298) Dioptric adjustment knob (p.44) Eyecup (p.183) AF point selection/ Magnify button (p.105/298) Viewfinder eyepiece Access lamp (p.33) Power switch (p.35) Strap mount (p.27) Menu button (p.52) Info button (p.
Nomenclature LCD panel Drive mode (p.111) u Single shooting o High-speed continuous shooting i Low-speed continuous shooting B Silent single shooting M Silent continuous shooting Q Self-timer: 10 sec./remote control k Self-timer: 2 sec./remote control AF operation (p.100) X One-Shot AF 9 AI Focus AF Z AI Servo AF 4L Manual focus Multi Shot Noise Reduction (p.141) HDR shooting (p.172) C Multiple-exposure shooting (p.
Nomenclature Viewfinder Information Spot metering circle (p.165) Zone AF (Manual zone selection) (p.103) Single-point AF (Manual selection) (p.103) Zone AF points (p.103) 19-point automatic selection AF (p.103) AF points (p.103) Focusing screen Grid (p.64) Electronic level (p.66) Battery check (p.36) AE lock (p.170) / AEB in-progress (p.168) Flash-ready (p.188, 193) Improper FE lock warning C FE lock (p.192) / FEB in-progress (p.201) High-speed sync (p.
Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). Creative Zone These modes give you more control for shooting various subjects. d : Program AE (p.158) s : Shutter-priority AE (p.160) f : Aperture-priority AE (p.162) a : Manual exposure (p.164) F : Bulb (p.171) Y P O Basic Zone Custom shooting mode You can register the shooting mode (d/s/ f/a/F), AF operation, menu settings, etc., to w and shoot (p.390).
Nomenclature Lens Lens without a distance scale Focusing ring (p.110, 247) Focus mode switch (p.40) Hood mount (p.42) Zoom position index Filter thread (front of lens) Zoom ring (p.41) Y P O Image Stabilizer switch (p.43) Contacts (p.19) Lens mount index (p.
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.28). Power plug Battery pack slot Charge Lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. C Y P O Battery Charger LC-E6E Charger for Battery Pack LP-E6 (p.28).
Getting Started Y P O This chapter explains preparatory steps before you start shooting and basic camera operations. C Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap (p.183).
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 Y P O As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully charged Battery Pack LP-E6 into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. 3 Y P O Close the cover. C Press the cover until it snaps shut.
Installing and Removing the Card The camera can use an SD, SDHC, or SDXC memory card (sold separately). An UHS-I Speed Class SDHC or SDXC memory card can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 Write-protect switch Open the cover. Slide the cover as shown by the arrows to open it. the card.
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent you from forgetting to insert a card (p.408). Removing the Card Access lamp 1 Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed, close the cover. Y P O the card.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to or read by the card, being erased, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Using the LCD Monitor After you flip out the LCD monitor, you can set menu functions, use Live View shooting, shoot movies, and play back images and movies. You can change the direction and angle of the LCD monitor. 1 Flip out the LCD monitor. the LCD monitor. 2 Rotate When the LCD monitor is swung out, 180° 90° 175° you can rotate it up or down or face it forward toward the subject. The indicated angles are only approximate. Y P O it toward you. 3 Face Normally, face the LCD monitor C toward you.
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 37 to set the date/time/zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera. Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, sensor cleaning will be executed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Display Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 Number of Possible Shots 9-1 0 [Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the date/time/zone setting screen will appear. Follow the steps below to set the time zone first. If you set the camera to the correct time zone for where you currently live, when you travel to another time zone you can simply set the camera to the correct time zone for your destination to update the camera’s date/time automatically.
3 Setting the Date, Time, and Zone the date and time. 4 SetPress the key to select the number. Press <0> so is displayed. Press the key to set the number, then press <0>. (Returns to .) saving time. 5 SetSettheit ifdaylight necessary. Press the key to select [Y]. Press <0> so is displayed. Press the key to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 4 will advance by 1 hour.
3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK]. Press the key to select the [52] tab. Press the key to select [LanguageK], then press <0>. C3 Y P O Set the desired language. Press the keys to select the language, then press <0>. X The interface language will change.
Attaching and Detaching a Lens The camera is compatible with all Canon EF and EF-S lenses. The camera cannot be used with EF-M lenses. Attaching a Lens 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the lens’ red or white mount White index index with the camera’s mount index of the same color. Turn the lens as shown by the arrow until it clicks in place. Red index C Y P O the lens focus mode switch to 3 Set .
Attaching and Detaching a Lens Zooming Turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrows. C Y P O Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens. To owners of the EF-S18-200mm f/3.5-5.
Attaching and Detaching a Lens Image Conversion Factor Since the image sensor size is smaller than the 35mm film format, it will look like the lens focal length is increased by approx. 1.6x. Image sensor size (Approx.) (22.5 x 15.0 mm / 0.88 x 0.59 in.) 35mm image size (36 x 24 mm / 1.42 x 0.94 in.) Attaching a Lens Hood A lens hood can block unwanted light and diminish rain, snow, dust etc. adhering to the front of the lens. Before storing the lens in a bag, etc., you can attach the hood in reverse.
Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF-S18-135mm f/3.5-5.6 IS STM lens as an example. * IS stands for Image Stabilizer. 1 Set the IS switch to <1>. Also set the camera’s power switch to <1>. the shutter button halfway. 2 Press X The Image Stabilizer will operate. the picture.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.183). If the camera dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (sold separately) is recommended. Holding the Camera Y P O To obtain sharp images, hold the camera still to minimize camera shake.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0). Pressing completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <6> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select or set the AF operation, drive mode, ISO speed, metering mode, AF point selection, etc.
Basic Operation 9 Multi-controller The Multi-controller <9> has eight keys that tilt in the directions shown by the arrows. Use the eight keys to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, etc. For menus and the Quick Control, the Multi-controller works only in the vertical and horizontal directions . It does not work in diagonal directions.
Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed. With the shooting function settings displayed, you can turn the Mode Dial to see the settings for each shooting mode (p.395).
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control. 1 Press the button. (7) X The Quick Control screen will appear. the desired functions. 2 SetPress the keys to select a function. X The setting of the selected function is displayed. Turn the <6> or <5> dial to change the setting. Basic Zone modes Y P O Creative Zone modes C the picture.
Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen Aperture (p.162) Shutter speed (p.160) Shooting mode*1 (p.24) Flash exposure compensation (p.193) AE lock*2 (p.170) Highlight tone priority*2 (p.145) Exposure compensation/ AEB setting (p.167/168) ISO speed (p.120) Wi-Fi function*3 Picture Style (p.126) Custom Controls (p.383) AF operation (p.100) Image-recording quality (p.116) Return White balance (p.134) Auto Lighting Optimizer (p.140) AF area selection mode (p.
3 Menu Operations You can set various settings with the menus such as the imagerecording quality, date/time, etc. While looking at the LCD monitor, use the button, keys, and <0> button on the camera back. button <0> button LCD monitor keys Menus in Basic Zone Modes C Y P O * Some menu tabs and menu items are not displayed in Basic Zone modes.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Press the key to select a menu tab. For example, in this manual, “the [z4] tab” refers to the screen displayed when the fourth z (Shooting) tab from the left [ ] is selected. the desired item. 3 Select Press the key to select the Y P O item, then press <0>. 4 Select the setting. C Press the keys to select the desired setting.
d Using the Touch Screen The LCD monitor is a touch-sensitive panel that you can operate with your fingers. Tap Quick Control (Sample display) Use your finger to tap (touch briefly and then remove your finger from) the LCD monitor. By tapping, you can select menus, icons, etc., displayed on the LCD monitor. When touch-screen operation is possible, a frame will appear around the icon (except on menu screens). For example, when you tap [Q], the Quick Control screen appears.
d Using the Touch Screen Drag Menu screen (Sample display) Slide your finger while touching the LCD monitor.
d Using the Touch Screen 3 Touch Control Settings 1 Select [Touch control]. Under the [53] tab, select [Touch control], then press <0>. the touch control setting. 2 SetSelect the desired setting, then press <0>. [Standard] is the normal setting. [Sensitive] provides a better touch response than [Standard]. Try using both settings and select the one you prefer. To disable touch-screen operations, select [Disable].
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card]. Under the [51] tab, select [Format card], then press <0>. Y P O the card.
Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed (p.432). Low-level Formatting Perform low-level formatting if the card’s recording or reading speed seems slow or if you want to erase all data on the card. Since low-level formatting will format all recordable sectors on the card, the formatting will take slightly longer than normal formatting.
Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved, during self-timer operation, and during touch screen operations. 1 Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. [Disable]. 2 Select Select [Disable], then press <0>. X The beeper will not sound. If [Touch to ] is selected, the beeper will be silent for touch screen operations only.
Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor immediately after capture. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. 1 Select [Image review]. Under the [z1] tab, select [Image review], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>. If [Hold] is set, the image will be displayed until the auto power off time elapses.
Before You Start 3 Reverting the Camera to the Default SettingsN The camera’s shooting function settings and menu settings can be reverted to their defaults. 1 Select [Clear all camera settings]. Under the [54] tab, select [Clear all camera settings], then press <0>. [OK]. 2 Select Select [OK], then press <0>.
Before You Start Image-recording Settings Camera Settings Image quality 73 Auto power off 1 min. Picture Style Auto Beep Enable Auto Lighting Optimizer Standard Release shutter without card Enable Peripheral illumination correction Enable/ Correction data retained Image review 2 sec.
Before You Start Live View Shooting Settings Live View shooting Movie Shooting Settings AF method Enable u+Tracking Movie Servo AF Enable AF method u+Tracking Continuous AF Enable Silent LV shooting Mode 1 Touch shutter Disable Metering timer 16 sec. Grid display Off Grid display Off Aspect ratio 3:2 1920x1080/IPB Exposure simulation Movie recording size Enable Digital zoom Disable Silent LV shooting Mode 1 Sound recording Auto Metering timer 16 sec.
Displaying the Grid You can display a grid in the viewfinder to help you straighten or compose the shot. 1 Select [VF grid display]. Under the [z1] tab, select [VF grid display], then press <0>. [Enable]. 2 Select Select [Enable], then press <0>. Y P O X When you exit the menu, the grid will appear in the viewfinder. C A grid can also be displayed on the LCD monitor during Live View shooting and movie shooting (p.229, 276).
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help correct camera tilt. Note that you can check only the horizontal tilt and not the forward/backward tilt. Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level.
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder During Shooting A simple electronic level using a camera icon can be displayed in the viewfinder at the center bottom. Since this can be displayed while you shoot, you can correct any tilt during handheld shooting. 1 Select [Viewfinder level]. Under the [z1] tab, select [Viewfinder level], then press <0>. [Show]. 2 Select Select [Show], then press <0>. C Y P O the shutter button halfway.
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder Before ShootingN The viewfinder can display an electronic level and grid using the AF points. This is convenient to correct any camera tilt before shooting with a tripod. 1 Select Custom Functions III. Under the [8] tab, select [C.Fn III: Operation/Others], then press <0>. C.Fn III -4 [Custom 2 Select Controls]. Y P O Press the key to select [4: Custom Controls], then press <0>. C3 Select [e].
Q Displaying the Electronic Level the electronic level. 5 Display Press the Depth-of-field preview button. X The viewfinder will display an electronic level and grid using the AF points. C Y P O 1° 6° Over Even when the tilt is corrected, there may be a margin of error of ±1°. If the camera is very tilted, the electronic level’s margin of error will be larger. If the Depth-of-field preview button has been assigned with [VF electronic level], depth-of-field preview (p.163) will not work.
Feature Guide and Help The Feature guide and Help display information about camera features. Feature Guide The Feature guide appears when you change the shooting mode or set a shooting function, Live View shooting, movie shooting, or Quick Control for playback, and displays a brief description of that mode, function or option. It also displays a description when you select a function or option on the Quick Control screen. When you proceed with the operation, the Feature guide will disappear.
Feature Guide and Help Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge. You can turn the <5> dial or press the key to scroll. Example: [z4: Long exp. noise reduction] B Î Y P O Example: [8C.Fn I-1: Exposure level increments] C B Î Example: [8C.
Basic Shooting Y P O This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. With Basic Zone modes, all you do is point and shoot while the camera sets everything automatically (p.91, 404). Also, to prevent botched pictures due to mistaken operations, advanced shooting function settings cannot be changed. ne ne C Zo ic o Basic Z s Ba When you set the Mode Dial to <8> while the LCD monitor is turned off, press the button (p.81) or button (p.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.75). 1 Area AF frame Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. the Area AF frame over the 2 Aim subject. All the AF points will be used to focus, and generally the closest object will be focused.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. X The captured image will be displayed for 2 sec. on the LCD monitor. After you finish shooting, push down the built-in flash with your fingers. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If the desired color tone is not obtained, use a Creative Zone mode and select a Picture Style other than and shoot (p.126).
A Fully Automatic Shooting (Scene Intelligent Auto) The flash fired even though it was daylight. For a backlit subject, the flash may fire to help lighten the subject’s dark areas. If you do not want the flash to fire, use the Quick Control to set [Flash firing] to [b] (p.90) or set the <7> (Flash Off) mode and shoot (p.77). The flash fired and the picture came out extremely bright. Move further from the subject and shoot.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, while you press the shutter button halfway to focus a still subject, the focus will be locked. You can then recompose the shot and press the shutter button completely to take the picture. This is called “focus lock”. Focus lock is also possible in other Basic Zone modes (except <5>).
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 215. the Live View shooting/Movie 1 Set shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. X The Live View image will appear on the LCD monitor. the subject. 3 Focus Press the shutter button halfway to focus.
7 Disabling Flash <7> is a fully-automatic shooting mode that does not use flash. It is useful in museums, aquariums, and other places where flash is prohibited. This mode is also effective for capturing the particular ambience of a scene, such as candlelight scenes. Shooting Tips C Y P O Prevent camera shake if the numeric display in the viewfinder blinks. Under low light when camera shake is prone to occur, the viewfinder’s shutter speed display will blink. Hold the camera steady or use a tripod.
C Creative Auto Shooting In the mode, you can easily blur the background and change the drive mode and flash firing. You can also choose the ambience you want to convey in your images. The default settings are the same as the mode. * CA stands for Creative Auto. 1 Set the Mode Dial to . the button. (7) 2 Press X The Quick Control screen will appear. Y P O the desired function. 3 SetPress the keys to select a function. X The selected function and Feature guide (p.69) will appear.
C Creative Auto Shooting Shutter speed Aperture ISO speed (1) (2) (4) (3) Battery check Possible shots Image-recording quality Pressing the button enables you to set the following: Y P O (1) Ambience-based shots You can choose the ambience you want to convey in your images. Turn the <6> or <5> dial to select the desired ambience. You can also select it from a list by pressing <0>. For details, see page 92.
C Creative Auto Shooting (3) Drive mode: Turn the <6> or <5> dial to select the desired drive mode. You can also select it from a list by pressing <0>. Single shooting: Shoot one image at a time. High-speed continuous shooting: While you hold down the shutter button completely, shots will be taken continuously. You can shoot up to approx. 7.0 shots per second. Low-speed continuous shooting: While you hold down the shutter button completely, shots will be taken continuously.
8: Special Scene Mode The camera will automatically choose the appropriate settings when you select a shooting mode for your subject or scene. 1 Set the Mode Dial to <8>. the button. (7) 2 Press X The Quick Control screen will appear. a shooting mode. 3 Select Press the keys to Y P O select a shooting mode icon. Turn the <6> or <5> dial to select a shooting mode. C You can also select the shooting mode icon and press <0> to display a list of shooting modes from which you can select one.
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and hair look softer. Shooting Tips C Y P O The further the distance between the subject and background, the better. The further the distance between the subject and background, the more blurred the background will look. The subject will also stand out better against an uncluttered dark background. Use a telephoto lens.
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips C Y P O With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end. It also adds breadth to landscapes. Shooting night scenes. The <3> mode is also good for night scenes because it disables the built-in flash.
4 Shooting Close-ups When you want to shoot flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips C Y P O Use a simple background. A simple background makes small objects such as flowers stand out better. Move as close as possible to the subject. Check the lens for its minimum focusing distance. Some lenses have indications such as on them.
5 Shooting Moving Subjects Use the <5> (Sports) mode to shoot a moving subject, such as a running child or a moving vehicle. Shooting Tips Y P O Use a telephoto lens. The use of a telephoto lens is recommended for shooting from a distance. C Track the subject with the Area AF frame. Aim the center AF point over the subject, then press the shutter button halfway to start autofocusing in Area AF frame. During autofocusing, the beeper will continue beeping softly.
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Using a tripod is recommended. Shooting Tips Y P O Use a wide-angle lens and a tripod. When using a zoom lens, use the wide-angle end to obtain a wide night view. Also, use a tripod to prevent camera shake. C Check the subject’s brightness. Under low light, the built-in flash will fire automatically to obtain a good exposure of the subject.
F Shooting Night Scenes (Handheld) Using a tripod for shooting a night scene yields the best results. However, with the (Handheld Night Scene) mode, you can shoot night scenes while handholding the camera. In this mode, four shots are taken continuously for each picture, and a resulting bright image with reduced camera shake is recorded. Shooting Tips C Y P O Hold the camera firmly. While shooting, hold the camera firmly and steadily.
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the (HDR Backlight Control) mode. When you take one picture in this mode, three continuous shots are taken at different exposures. This results in one image, with a wide tonal range, that has minimized the blocked-up shadows caused by backlighting. Shooting Tips C Y P O Hold the camera firmly. While shooting, hold the camera firmly and steadily. In this mode, three shots are aligned and merged into a single image.
Cautions for <6> Night Portrait and Handheld Night Scene During Live View shooting, it may be difficult to focus dots of light such as in a night scene. In such a case, set the lens’ focus mode switch to and focus manually. Cautions for Handheld Night Scene and HDR Backlight Control Compared with other shooting modes, the shooting area will be smaller. You cannot select RAW or RAW+JPEG. If RAW is set, the image will be recorded in the 73 quality.
Q Quick Control Cautions for HDR Backlight Control Note that the image may not be rendered with a smooth gradation and may look irregular or have significant noise. HDR Backlight Control may not be effective for excessively backlit scenes or extremely high-contrast scenes. Q Quick Control In Basic Zone modes when the shooting function settings screen is displayed, you can press the button to display the Quick Control screen.
Q Quick Control Settable Functions in Basic Zone Modes o: Default setting k: User selectable : Not selectable Function A 7 C u: Single shooting o: High-speed continuous shooting i: Low-speed continuous shooting Drive B: Silent single shooting mode M: Silent continuous shooting Q Self-timer (p.113) k a: Automatic firing Flash D: Flash on (Fires at all times) firing b: Flash off Ambience-based shots (p.92) Light/scene-based shots (p.96) Blurring/sharpening the background (p.
Shoot by Ambience Selection Except in the , <7>, and Basic Zone modes, you can select the ambience for shooting.
Shoot by Ambience Selection X The LCD monitor will display how the image will look with the selected ambience. the ambience effect. 5 SetPress the key to select the effect bar so that [Effect] appears at the bottom. Press the key to select the desired effect. the picture. 6 TakePress the shutter button completely to C take the picture. To return to viewfinder shooting, press the <0> button to exit Live View shooting. Then press the shutter button completely to take the picture.
Shoot by Ambience Selection Ambience Settings Standard setting Standard image characteristics for the respective shooting mode. Note that <2> has image characteristics geared for portraits and <3> is geared for landscapes. Each ambience is a modification of the respective shooting mode’s image characteristics. Vivid The subject will look sharp and vivid. It makes the photo look more impressive than with [ Standard setting]. Soft The subject will look softer and more dainty.
Shoot by Ambience Selection Brighter The picture will look brighter. Darker The picture will look darker. Monochrome The picture will be monochrome. You can select the monochrome color to be black and white, sepia, or blue. When [Monochrome] is selected, will appear in the viewfinder.
Shoot by Lighting or Scene Type In the <2>, <3>, <4>, and <5> Basic Zone modes, you can shoot while the settings match the lighting or scene type. Normally, [ Default setting] is adequate, but if the settings match the lighting condition or scene, the picture will look more accurate to your eye. For Live View shooting, if you set both [Light/scene-based shots] and [Ambience-based shots] (p.92), you should first set [Light/scenebased shots].
Shoot by Lighting or Scene Type the Quick Control screen, 4 On select the lighting or scene type. Press the button (7). Press the key to select [ Default setting]. [Light/scenebased shots] will appear on the screen. Press the key to select the desired lighting or scene type. X The resulting image with the selected lighting or scene type will be displayed. the picture. 5 TakePress the shutter button completely to C Y P O take the picture.
Shoot by Lighting or Scene Type Lighting or Scene Type Settings Default setting Default setting suited for most subjects. Daylight For subjects under sunlight. Gives more natural-looking blue skies and greenery and reproduces light-colored flowers better. Shade For subjects in the shade. Suitable for skin tones, which may look too bluish, and for light-colored flowers. Cloudy For subjects under overcast skies. Makes skin tones and landscapes, which may otherwise look dull on a cloudy day, look warmer.
Setting the AF and Drive Modes Y P O The 19 AF points in the viewfinder make AF shooting suitable for a wide variety of subjects and scenes. C You can also select the AF operation and drive mode that best match the shooting conditions and subject. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). In Basic Zone modes, the AF operation and AF point (AF area selection mode) are set automatically. stands for autofocus.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. 1 Set the lens focus mode switch to . the Mode Dial to a Creative 2 Turn Zone mode. 3 Press the button. (9) Y P O the AF operation. 4 Select While looking at the LCD panel, turn C the <6> or <5> dial.
f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus confirmation light in the viewfinder will also light up. With evaluative metering, the AF point exposure setting will be set at the Focus confirmation light same time focus is achieved.
f: Selecting the AF OperationN AI Focus AF for Switching the AF Operation Automatically AI Focus AF switches the AF operation from One-Shot AF to AI Servo AF automatically if a still subject starts moving. After the subject is focused in One-Shot AF, if the subject starts moving, the camera will detect the movement, change the AF operation automatically to AI Servo AF, and keep tracking the moving subject.
S Selecting the AF AreaN 19 AF points are provided for AF. You can select the AF point(s) suiting the scene or subject. AF Area Selection Mode You can select one of three AF area selection modes. See the next page for the selection procedure. : Single-point AF (Manual selection) Select one AF point to focus. : Zone AF (Manual zone selection) Y P O The 19 AF points are divided into five zones for focusing. C : 19-point automatic selection AF All the AF points are used to focus.
S Selecting the AF AreaN Selecting the AF Area Selection Mode 1 Press the or button. (9) Look through the viewfinder and press the or button. the button. 2 Press Each time you press the AF area selection mode button, the AF area selection mode changes. The AF area selection mode currently set is indicated on the top of the viewfinder. : Single-point AF (Manual selection) : Zone AF (Manual zone selection) : 19-point automatic selection AF C Y P O With [8C.
S Selecting the AF AreaN Selecting the AF Point Manually You can manually select the AF point or zone. If 19-point automatic selection AF + AI Servo AF has been set, you can select any position where AI Servo AF is to start. 1 Press the or button. (9) X The AF points will be displayed in the viewfinder. In the Zone AF mode, the selected zone will be displayed. an AF point. 2 Select The AF point selection will change in Y P O the direction you tilt <9>.
AF Area Selection Modes Single-point AF (Manual Selection) Select one AF point to be used for focusing. Zone AF (Manual Zone Selection) The 19 AF points are divided into five zones for focusing. All the AF points in the selected zone are used for the automatic selection of the point of focus. It makes achieving focus easier than with single-point AF and it is effective for moving subjects.
AF Area Selection Modes 19-point Automatic Selection AF All the AF points are used to focus. This mode is set automatically in Basic Zone modes. With One-Shot AF, pressing the shutter button halfway will display the AF point(s) that achieved focus. If multiple AF points are displayed, it means they all have achieved focus. This mode tends to focus the nearest subject. With AI Servo AF, the manually-selected (p.105) AF point is used first to achieve focus.
AF Area Selection Modes AF Operation and Maximum Lens Apertures Maximum Lens Aperture: f/3.2 - f/5.6 With all AF points, cross-type AF sensitive to both vertical and horizontal lines is possible. However, with the lenses below, the peripheral AF points will detect only vertical or horizontal lines (no cross-type focusing).
When Autofocus Fails Autofocus can fail to achieve focus (viewfinder’s focus confirmation light blinks) with certain subjects such as the following: Subjects Difficult to Focus Very low-contrast subjects (Example: Blue sky, solid-color walls, etc.) Subjects in very low light Extremely backlit and reflective subjects (Example: Car with a highly reflective body, etc.) Near and far subjects covered by an AF point (Example: Animal in a cage, etc.
When Autofocus Fails MF: Manual Focus 1 Set the lens focus mode switch to . X <4 L> will be displayed on the LCD panel. Focusing ring the subject. 2 Focus Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder. C Y P O If you press the shutter button halfway during manual focusing, the AF point that achieved focus and the focus confirmation light will light up in the viewfinder.
i Selecting the Drive Mode Single and continuous drive modes are provided. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel, turn the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. Y P O o : High-speed continuous shooting (Max. approx. 7.0 shots/sec.) i : Low-speed continuous shooting (Max. approx. 3.0 shots/sec.) While you hold down the shutter button completely, shots will be taken continuously.
i Selecting the Drive Mode If or is set, the time lag from when you press the shutter button completely until the picture is shot will be slightly longer than with normal single or continuous shooting. When the battery level is low, the continuous shooting speed may become slightly slower. In AI Servo AF operation, the continuous shooting speed may become slightly slower depending on the subject and the lens used. o: The maximum continuous shooting speed of approx. 7 shots/sec.
j Using the Self-timer Use the self-timer when you want to be in the picture. 1 Press the button. (9) the self-timer. 2 Select While looking at the LCD panel, turn the <6> or <5> dial to select the self-timer delay. Q : 10-sec. self-timer k : 2-sec. self-timer picture. 3 TakeLookthethrough the viewfinder, focus C Y P O the subject, then press the shutter button completely. X You can check the self-timer operation with the self-timer lamp, beeper, and countdown display (in seconds) on the LCD panel.
MEMO C 114 Y P O
Image Settings Y P O This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. C In Basic Zone modes, only the following can be set as described in this chapter: Image-recording quality, lens peripheral illumination correction, lens chromatic aberration correction, folder creation and selection, and image file numbering.
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG imagerecording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.118). 1 Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording quality. 2 Select To select a RAW setting, turn the <6> dial. To select a JPEG setting, press the key.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Image Quality Pixels Recorded Printing Size 20M A2 8.9M A3 5.0M A4 b*1 2.5M 9x13 cm 1.3 4990 4990 (4990) c*2 0.3M - 0.3 19380 19380 (19380) 1 15 (16) 73 83 74 JPEG 84 7a 8a File Size (MB) Possible Shots Maximum Burst 6.6 1000 40 (65) 3.5 1920 130 (1920) 3.6 1840 100 (1840) 1.8 3410 3410 (3410) 2.3 2790 430 (2790) 1.2 5200 5200 (5200) 20M A2 24.
3 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded simultaneously to the card in both RAW and JPEG at the imagerecording qualities that were set. The two images will be recorded with the same file numbers (file extension: .JPG for JPEG and .CR2 for RAW). The image-recording quality icons are as follows: 1 (RAW), 41 (Middle RAW), 61 (Small RAW), JPEG, 7 (Fine), 8 (Normal), 3 (Large), 4 (Middle), 6 (Small).
3 Setting the Image-Recording Quality Maximum Burst During Continuous Shooting The approximate maximum burst is displayed on the bottom right in the viewfinder and on the shooting function settings screen. If the maximum burst for continuous shooting is 99 or higher, “99” will be displayed. C Y P O The maximum burst is displayed even when a card is not inserted in the camera. Make sure that a card is inserted before taking a picture.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically (p.122). Regarding the ISO speed during movie shooting, see pages 254 and 257. 1 Press the button. (9) the ISO speed. 2 SetWhile looking at the LCD panel or the Y P O viewfinder, turn the <6> or <5> dial. ISO speed can be set within ISO 100 - ISO 12800 in 1/3-stop increments. “A” indicates Auto ISO.
i: Setting the ISO SpeedN If [z4: Highlight tone priority] is set to [Enable], ISO 100/125/160 and “H” (equivalent to ISO 25600) cannot be set (p.145). Shooting in high temperatures may result in images that look grainier. Long exposures can also cause irregular colors in the image. When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable.
i: Setting the ISO SpeedN Auto ISO If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within ISO 100 - ISO 12800 and the maximum limit within ISO 200 - H (equivalent to ISO 25600). 1 Select [ISO speed settings]. Under the [z3] tab, select [ISO speed settings], then press <0>. [ISO speed range]. 2 Select Select [ISO speed range], then press Y P 3O C <0>. Set the minimum limit. Select the minimum limit box, then press <0>.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range for Auto ISO You can set the automatic ISO speed range for Auto ISO within ISO 100 - ISO 12800. You can set the minimum limit within ISO 100 - ISO 6400, and the maximum limit within ISO 200 - ISO 12800 in whole-stop increments. 1 Select [Auto ISO range]. Select [Auto ISO range], then press <0>. the minimum limit. 2 SetSelect the minimum limit box, then Y P O press <0>. Press the key to select an ISO speed, then press <0>.
i: Setting the ISO SpeedN 3 Setting the Minimum Shutter Speed for Auto ISO When Auto ISO is set, you can set the minimum shutter speed (1/250 sec. to 1 sec.) so that the automatically-set shutter speed is not too slow. This is convenient in the and modes when you use a wideangle lens to shoot a moving subject. You can minimize both camera shake and subject blur. 1 Select [Min. shutter spd.]. Select [Min. shutter spd.], then press <0>. Y P O the desired minimum shutter 2 Set speed.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, (Auto) is set automatically. 1 Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>. X The Picture Style selection screen will appear. a Picture Style. 2 Select Press the key to select a Picture Style, then press <0>. X The Picture Style will be set.
A Selecting a Picture StyleN R Landscape For vivid blues and greens, and very sharp and crisp images. Effective for impressive landscapes. S Neutral This Picture Style is for users who prefer to process images with their computer. For natural colors and subdued images. U Faithful This Picture Style is for users who prefer to process images with their computer. When the subject is captured under a color temperature of 5200 K, the color is adjusted colorimetrically to match the subject’s color.
A Selecting a Picture StyleN Symbols The symbols of the Picture Style selection screen refer to parameters such as [Sharpness] and [Contrast]. The numerals indicate the parameter settings, such as for [Sharpness] and [Contrast], for each Picture Style.
A Customizing a Picture StyleN You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see page 131. 1 Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>. X The Picture Style selection screen will appear. a Picture Style. 2 Select Select a Picture Style, then press the button. Y P 3O C Select a parameter.
A Customizing a Picture StyleN Press the button to save the adjusted parameters. The Picture Style selection screen will reappear. X Any parameter settings different from the default will be displayed in blue. Parameter Settings and Effects g Sharpness 0: Less sharp outline +7: Sharp outline h Contrast -4: Low contrast +4: High contrast i Saturation -4: Low saturation +4: High saturation j Color tone -4: Reddish skin tone +4: Yellowish skin tone C Y P O By selecting [Default set.
A Customizing a Picture StyleN V Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page. kFilter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. Filter Sample Effects N: None Normal black-and-white image with no filter effects. Ye: Yellow The blue sky will look more natural, and the white clouds will look crisper.
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create multiple Picture Styles with different settings for parameters such as sharpness and contrast. You can also adjust the parameters of a Picture Style that has been registered to the camera with EOS Utility (provided software, p.456). 1 Select [Picture Style].
A Registering a Picture StyleN a parameter. 5 Select Select a parameter such as [Sharpness], then press <0>. the parameter. 6 SetPress the key to adjust the parameter as desired, then press <0>. For details, see “Customizing a Picture Style” on page 129. C Press the button to register the modified Picture Style. The Picture Style selection screen will then reappear. X The base Picture Style will be indicated on the right of [User Def. *].
3 Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the (Auto) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with , you can select the white balance to match the light source or set it manually by shooting a white object. In Basic Zone modes, is set automatically. 1 Select [White balance]. Under the [z3] tab, select [White balance], then press <0>. a white balance setting.
3 Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Perform this procedure under the actual light source to be used. 1 Shoot a white object. Look through the viewfinder and aim the entire dotted line box (shown in the illustration) over a plain, white object. Focus manually and set the standard exposure for the white object. You can use any white balance setting.
3 Setting the White BalanceN [White balance]. 4 Select Under the [z3] tab, select [White balance], then press <0>. the custom white balance. 5 Select Select [ ], then press <0>. O C Y P O If the exposure obtained in step 1 differs greatly from the standard exposure, a correct white balance may not be obtained. In step 3, the following images cannot be selected: images captured while the Picture Style was set to [Monochrome], multiple-exposure images, and images shot with another camera.
3 Setting the White BalanceN P Setting the Color Temperature You can set the white balance’s color temperature numerically. This is for advanced users. 1 Select [White balance]. Under the [z3] tab, select [White balance], then press <0>. the color temperature. 2 SetSelect [P]. C Turn the <6> dial to set the color temperature, then press <0>. The color temperature can be set from approx. 2500 K to 10000 K in 100 K increments.
3 White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters. White Balance Correction 1 Select [WB Shift/Bkt.]. Under the [z3] tab, select [WB Shift/Bkt.], then press <0>.
3 White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images with different color tones can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/ green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
3 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically. 1 Select [Auto Lighting Optimizer]. Under the [z3] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced. 1 Select [High ISO speed NR]. Under the [z4] tab, select [High ISO speed NR], then press <0>. the level. 2 SetSelect the desired noise reduction Y P O level, then press <0>.
3 Setting Noise ReductionN Cautions for Setting Multi Shot Noise Reduction If there is significant misalignment in the image due to camera shake, the noise reduction effect may be minimal. If you are handholding the camera, keep it steady to prevent camera shake. Using a tripod is recommended. If you shoot a moving subject, the subject’s movement may leave afterimages or the surrounding area of the subject may become dark.
3 Setting Noise ReductionN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z4] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetSelect the desired setting, then press <0>. Y P O Auto For exposures of 1 sec. or longer, noise reduction is performed automatically if noise typical of long exposures is detected. This [Auto] setting is effective in most cases.
3 Setting Noise ReductionN With [Auto] and [Enable], the noise reduction process after the picture is taken may take the same amount of time as that for the exposure. Shooting is disabled when noise reduction is performed. Images taken at ISO 1600 or higher may look grainier with the [Enable] setting than with the [Disable] or [Auto] setting.
3 Highlight Tone PriorityN You can minimize overexposed highlight areas. 1 Select [Highlight tone priority]. Under the [z4] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. Y P O picture. 3 TakeThetheimage will be recorded with C highlight tone priority applied.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. Both lens aberrations can be corrected. The default settings are [Enable] for both corrections. Peripheral Illumination Correction 1 Select [Lens aberration correction]. Under the [z2] tab, select [Lens aberration correction], then press <0>.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “Lens Correction Data” on the next page. picture. 2 TakeThetheimage will be recorded with the Y P O chromatic aberration corrected.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Lens Correction Data The camera already contains lens peripheral illumination correction data and chromatic aberration correction data for approx. 25 lenses. If you select [Enable], the peripheral illumination correction and chromatic aberration correction will be applied automatically for any lens whose correction data is registered in the camera.
3 Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder 1 Select [Select folder]. Under the [51] tab, select [Select folder], then press <0>. [Create folder]. 2 Select Select [Create folder], then press Y P O <0>. C3 Create a new folder. Select [OK], then press <0>.
3 Creating and Selecting a Folder Selecting a Folder Lowest file number Number of images in folder With the folder selection screen displayed, select a folder and press <0>. X The folder where the captured images will be saved is selected. Subsequent captured images will be recorded into the selected folder. Folder name Highest file number C Y P O Folders As with “100CANON” for example, the folder name starts with three digits (the folder number) followed by five alphanumeric characters.
3 File Numbering Methods The image files will be numbered from 0001 to 9999 in the order the images are taken, then saved in a folder. You can change how the file number is assigned. 1 (Example) IMG_0001.JPG File number Select [File numbering]. Under the [51] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Select the desired setting, then press <0>. Continuous Y P O Continues the file numbering sequence even after the card is replaced or a new folder is created.
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. When you replace the card or create a folder, the file numbering restarts from 0001 for the new images saved. This is convenient if you want to organize images according to cards or folders.
3 Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. 1 Select [Copyright information]. Under the [54] tab, select [Copyright information], then press <0>. the option to be set. 2 Select Select [Enter author’s name] or [Enter copyright details], then press <0>. Y P O text. 3 Enter Press the button. The text C palette will be highlighted in a color frame, and text can be entered.
3 Setting Copyright InformationN the setting. 4 ExitAfter entering the text, press the button, then select [OK]. X The information will be saved and the screen will return to step 2. Checking the Copyright Information When you select [Display copyright info.] in step 2, you can check the [Author] and [Copyright] information that you entered.
3 Setting the Color SpaceN The range of reproducible colors is called the color space. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In Basic Zone modes, sRGB is set automatically. 1 Select [Color space]. Under the [z3] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>.
MEMO C 156 Y P O
Advanced Operations Y P O In Creative Zone modes, you can set the shutter speed and/ or aperture to set the exposure as desired. By changing the camera settings, you can obtain various results. C The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the LCD panel for 4 sec. (0).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . the subject. 2 Focus Look through the viewfinder and aim the AF point over the subject. Then press the shutter button halfway. X When focus is achieved, the focus confirmation light on the viewfinder’s bottom right will light up (when in One-Shot AF mode).
d: Program AE If the “30"” shutter speed and the lower f/number blink, it indicates underexposure. Increase the ISO speed or use flash. If the “8000” shutter speed and the higher f/number blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and Modes In the mode, many functions, such as the AF operation and metering mode, are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen action (Fast shutter speed: 1/2000 sec.
s: Shutter-Priority AE If the lower f/number blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the higher f/number blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “8000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/ number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/ number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000"” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (higher aperture f/number) until the shutter speed blinking stops or set a lower ISO speed. Aperture Display The higher the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . 2 Set the ISO speed (p.120). speed and aperture. 3 SetTothesetshutter the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
q Selecting the Metering ModeN If Auto ISO is set, the ISO speed setting will change to suit the shutter speed and aperture in order to obtain a standard exposure. Therefore, you may not obtain the desired exposure effect. In [z3: Auto Lighting Optimizer], if the checkmark for [Disabled in M or B modes] is removed, Auto Lighting Optimizer can be set in the and modes (p.140). When Auto ISO is set, you can press the button to lock the ISO speed.
q Selecting the Metering ModeN w Partial metering Effective when the background is much brighter than the subject due to backlighting, etc. The metering is weighted at the center covering approx. 7.7% of the viewfinder area. r Spot metering This is for metering a specific spot of the subject or scene. The metering is weighted at the center covering approx. 3.0% of the viewfinder area. e Center-weighted average metering The metering is weighted at the center and then averaged for the entire scene.
Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z3] tab, select [Expo.comp./AEB], then press <0>. the AEB range. 2 SetTurn the <6> dial to set the AEB AEB range range. Press the key to set the exposure compensation amount. Press <0> to set it.
h Auto Exposure Bracketing (AEB)N During AEB shooting, in the viewfinder and on the LCD panel will blink. If the drive mode is set to or , press the shutter button three times for each shot. When , , or is set and you hold down the shutter button completely, the three bracketed shots will be taken continuously and the camera will automatically stop shooting. When or is set, the three bracketed shots will be taken continuously after a 10-sec. or 2-sec. delay.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the shot. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. Press the shutter button halfway. X The exposure setting will be displayed. the button.
F: Bulb Exposures In this mode, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, astronomical objects, and other subjects requiring long exposures. 1 Set the Mode Dial to . the desired aperture. 2 SetWhile looking at the LCD panel, turn the <6> or <5> dial. Y P O picture.
w: HDR (High Dynamic Range) ShootingN Highlight detail and shadow detail are retained for a high dynamic range of tones even with high-contrast scenes. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured for each shot and then merged together automatically. The HDR image is recorded as a JPEG image. * HDR stands for High Dynamic Range. 1 Select [HDR Mode].
w: HDR (High Dynamic Range) ShootingN [Continuous HDR]. 3 SetSelect either [1 shot only] or [Every shot], then press <0>. With [1 shot only], HDR shooting will be canceled automatically after the shooting ends. With [Every shot], HDR shooting continues until the setting in step 2 is set to [Disable HDR]. Image Align]. 4 SetFor[Auto handheld shooting, select [Enable]. When using a tripod, select [Disable], then press <0>. Y P O picture.
w: HDR (High Dynamic Range) ShootingN If you shoot a moving subject, the subject’s movement may leave afterimages or the surrounding area of the subject may become dark. To prevent camera shake, the ISO speed may be set higher than usual. HDR shooting is not possible with ISO expansion. (HDR shooting is possible within the range of ISO 100 - ISO 12800.) When shooting HDR images with [Auto Image Align] set to [Enable], AF point display information (p.294) and Dust Delete Data (p.
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.215), you can see how the single exposures merge while shooting. 1 Select [Multiple exposure]. Under the [z4] tab, select [Multiple exposure], then press <0>. [Multiple exposure]. 2 SetSelect [Enable], then press <0>. To exit shooting multiple exposures, select [Disable].
P Multiple ExposuresN [Multi-expos ctrl]. 3 SetSelect the desired multiple-exposure control method, then press <0>. Additive The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation. Exposure Compensation Setting Guide for Multiple Exposures Two exposures: -1 stop, three exposures: -1.
P Multiple ExposuresN [Continue Mult-exp]. 5 SetSelect either [1 shot only] or [Continuously], then press <0>. With [1 shot only], multiple-exposure shooting will be canceled automatically after the shooting ends. With [Continuously], multipleexposure shooting continues until the setting in step 2 is set to [Disable]. the first exposure. 6 Take X The captured image will be displayed. Remaining number of exposures C7 X The
icon will blink.
P Multiple ExposuresN Only the merged multiple-exposure image will be saved. The images taken in steps 6 and 7 for the multiple-exposure image will not be saved. With multiple exposures, the more exposures there are, the more noticeable the noise, irregular colors, and banding will be. Also, as noise increases with higher ISO speeds, shooting at low ISO speeds is recommended. If [Additive] is set, the image processing after taking the multiple exposures will take time.
P Multiple ExposuresN Merging Multiple Exposures with an Image Recorded on the Card You can select an image recorded on the card as the first single exposure. The original of the selected image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images. 1 Select [Select image for multi. expo.]. Select [Select image for multi. expo.], then press <0>. X The images on the card will be displayed. an image.
P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single exposure. If you select [Deselect img], the selected image will be canceled. Checking and Deleting Multiple Exposures During Shooting Before you finish shooting the set number of exposures, you can press the button to view the merged multiple-exposure image so far. You can check how it looks and the exposure. If you press the button, the operations possible during multipleexposure shooting will be displayed.
P Multiple ExposuresN FAQ Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Image-Recording Quality Setting Merged Multiple-Exposure JPEG JPEG 1 1 41/61 1 1+JPEG 1+JPEG 41/61+JPEG 1+JPEG Can I merge images recorded on the card? With [Select image for multi. expo.], you can select the first single exposure from the images recorded on the card (p.179).
2 Mirror LockupN Although using the self-timer or a remote switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). 1 Set [Mirror lockup] to [Enable]. Under the [z2] tab, select [Mirror lockup], then press <0>. Select [Enable], then press <0>. 2 Focus the subject, then press the shutter button completely. XThe mirror will swing up.
Using the Eyepiece Cover When you use the self-timer, bulb, or a remote switch and do not look through the viewfinder, stray light entering the viewfinder can cause the image to look dark. To prevent this, use the eyepiece cover (p.27) attached to the camera strap. During Live View shooting and movie shooting, attaching the eyepiece cover is unnecessary. 1 Detach the eyecup. Push the bottom of the eyecup to detach. the eyepiece cover.
F Using a Remote Switch You can connect Remote Switch RS-60E3 (sold separately) to the camera and shoot (p.416). For detailed instructions, refer to the remote switch’s instruction manual. 1 Open the terminal cover. the plug to the remote 2 Connect control terminal. R Remote Control Shooting Y P O With Remote Controller RC-6 (sold separately), you can shoot remotely up to approx. 5 meters/16.4 feet from the camera. You can either shoot immediately or use a 2-sec. delay.
R Remote Control Shooting the self-timer. 4 Select Look at the LCD panel and turn the <6> dial to select or . the remote controller's 5 Press transmit button. Point the remote controller toward the camera’s remote control sensor and press the transmit button. X The self-timer lamp lights up and the picture is taken. Remote control sensor C Y P O Fluorescent or LED lighting may cause camera misoperation by triggering the shutter inadvertently. Try to keep the camera away from such light sources.
MEMO C 186 Y P O
Flash Photography Y P O This chapter explains how to use the built-in flash and external Speedlites (EX-series, sold separately), how to set flash settings with the menu, and how to use the built-in flash for wireless flash shooting. C Flash cannot be used with movie shooting. (It will not fire.
D Using the Built-in Flash In Creative Zone modes, just press the button to raise the built-in flash for flash photography. To retract the built-in flash, push it back down with your fingers. In Basic Zone modes (except <7> <3> <5> modes), the built-in flash will be raised and fire automatically in low-light and backlit conditions. In the <2> <4> modes, you have the option to fire the flash or not.
D Using the Built-in Flash Effective Range of Built-in Flash [Approx. in meters/feet] EF-S18-55mm f/3.5-5.6 IS STM EF-S18-135mm f/3.5-5.6 IS STM EF-S18-200mm f/3.5-5.6 IS ISO Speed Wide Angle: f/3.5 Telephoto: f/5.6 100 1-3.4/3.3-11.2 1-2.1/3.3-7.0 200 1-4.8/3.3-15.9 1-3.0/3.3-9.9 400 1-6.9/3.3-22.5 1-4.3/3.3-14.1 800 1.2-9.7/4.0-31.8 1-6.1/3.3-19.9 1600 1.7-13.7/5.6-45.0 1.1-8.6/3.5-28.1 3200 2.4-19.4/8.0-63.6 1.5-12.1/5.0-39.8 6400 3.4-27.4/11.2-90.0 2.1-17.1/7.0-56.2 12800 4.
D Using the Built-in Flash 3 Red-eye Reduction Using the red-eye reduction lamp before flash photography can reduce red eye. Red-eye reduction will function in any shooting mode except <7>, <3>, <5>, and . 1 Select [Red-eye reduc.]. Under the [z2] tab, select [Red-eye reduc.], then press <0>. [Enable]. 2 Select Select [Enable], then press <0>. For flash photography, when you press the shutter button halfway, the red-eye reduction lamp will light up.
D Using the Built-in Flash [y]. 2 Select Press the keys to select [y*], then press <0>. X The flash exposure compensation screen will appear. the exposure compensation 3 Set amount. To make the flash exposure brighter, turn the <5> or <6> dial to the right (increased exposure). To make it darker, turn the <5> or <6> dial to the left (decreased exposure). Y P O X When you press the shutter button halfway, the icon will appear in the viewfinder.
D Using the Built-in Flash A FE LockN FE (flash exposure) lock obtains and locks the appropriate flash exposure for the desired part of the subject as framed. 1 Press the button. X The built-in flash will rise. Press the shutter button halfway and look in the viewfinder to check that the icon is lit. 2 Focus the subject. the button. (8) 3 Press Aim the viewfinder center over the Y P O subject where you want to lock the flash exposure, then press the button.
D Using an External Speedlite EOS-dedicated, EX-series Speedlites Flash photography with EX-series Speedlite (sold separately) is as easy as with built-in flash. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions with the camera’s menu, see pages 195-202.
D Using an External Speedlite Canon Speedlites Other Than the EX-series With an EZ/E/EG/ML/TL-series Speedlite set to A-TTL or TTL autoflash mode, the flash can be fired at full output only. Set the camera’s shooting mode to (manual exposure) or (aperture-priority AE) and adjust the aperture setting before shooting. When using a Speedlite that has manual flash mode, shoot in the manual flash mode.
3 Setting the FlashN With the built-in flash or an EX-series Speedlite compatible with flash function settings, you can use the camera’s menu screen to set flash functions and the external Speedlite’s Custom Functions. If you use an external Speedlite, attach the Speedlite to the camera and turn on the Speedlite before setting the flash functions. For details on the external Speedlite’s flash functions, refer to the Speedlite’s instruction manual. 1 Select [Flash control].
3 Setting the FlashN Flash Synchronization Speed in Av Mode You can set the flash sync speed for flash photography in the aperture-priority AE (f) mode. : Auto The flash sync speed is set automatically within a range of 1/250 sec. to 30 sec. to suit the scene’s brightness. High-speed sync is also possible. : 1/250-1/60 sec. auto Prevents a slow shutter speed from being set in low-light conditions. It is effective for preventing subject blur and camera shake.
3 Setting the FlashN Built-in Flash Settings Flash mode Normally, set this to [E-TTL II]. This enables autoexposure shooting with the built-in flash. To set the flash output level manually, select [Manual flash]. Select [2flash output], then set the flash output level to within 1/1 - 1/128 (1/3-stop increments) before shooting. Shutter synchronization Y P O Normally, set this to [1st curtain] so that the flash fires immediately after the exposure starts.
3 Setting the FlashN 2 Flash exposure compensation The same setting as step 3 in “Flash Exposure Compensation” on page 190 can be set. Wireless functions With wireless flash photography (via optical transmission), you can use the built-in flash to control an external Speedlite. For details, see “Using Wireless Flash” on page 203.
3 Setting the FlashN External Flash Function Settings The screen display and setting options will differ depending on the external Speedlite model, current flash mode, Speedlite’s Custom Function settings, etc. For details on your Speedlite’s flash functions, refer to the Speedlite’s instruction manual.
3 Setting the FlashN Wireless functions Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the instruction manual of a Speedlite compatible with the wireless flash shooting. Flash zoom (Flash coverage) With Speedlites having a zooming flash head, you can set the flash coverage. Normally, set this to [AUTO] so that the camera will automatically set the flash coverage to match the lens focal length.
3 Setting the FlashN Flash exposure compensation The same setting as step 3 in “Flash Exposure Compensation” on page 190 can be set. For details, refer to the Speedlite’s instruction manual. Flash exposure bracketing While the flash output is changed automatically, three shots are taken. For details, refer to the instruction manual of a Speedlite compatible with flash exposure bracketing. C Y P O When using second-curtain synchronization, set the shutter speed to 1/25 sec. or slower.
3 Setting the FlashN External Speedlite Custom Function Settings For details on the external Speedlite’s Custom Functions, refer to the Speedlite’s instruction manual. 1 Select [External flash C.Fn setting]. Select [External flash C.Fn setting], then press <0>. the desired function. 2 SetPress the key to select the number, then press <0>. Select the setting, then press <0>. Clear Settings 1 Y P O Select [Clear settings]. C Select [Clear settings], then press <0>. the settings to be cleared.
Using Wireless FlashN The camera’s built-in flash can work as a master unit with Canon Speedlites with a wireless slave feature via optical transmission and wirelessly trigger the Speedlite(s) to fire. Be sure to read about wireless flash photography (optical transmission) in the Speedlite’s instruction manual. Slave Unit Settings and Position Regarding your Speedlite (slave unit), refer to its instruction manual and set it as follows.
Using Wireless FlashN *1: If the Speedlite does not have a transmission channel setting function, the camera can work with any channel. *2: In small rooms, the slave unit may work even if its wireless sensor does not face the camera. The camera’s wireless signals can bounce off the walls and be received by the slave unit. When using an EX-series Speedlite with fixed flash head and wireless sensor, take pictures to make sure it can fire.
Using Wireless FlashN Wireless Flash Shooting Configurations The table below shows the possible configurations for wireless flash shooting. Choose the configuration suiting the subject, shooting conditions, and the number of external Speedlites you use. External Speedlite A:B Flash Quantity Ratio Setting Wireless Firing Group Functions Single - - p.206 0 Single - Used p.208 0:3 - Multiple - - p.209 0 1 All Set - p.
Using Wireless FlashN Fully Automatic Shooting with One External Speedlite This shows the most basic setup for fully-automatic wireless flash shooting with one external Speedlite. Steps 1 to 4 and 6 apply to all wireless flash shooting. Therefore, these steps are omitted in the other wireless flash setups explained on the pages hereafter. On the menu screens, the <0> and <1> icons refer to the external Speedlite, and the <3> and <2> icons refer to the built-in flash.
Using Wireless FlashN mode: E-TTL II]. 4 SetSet[Flash [Flash mode] to [E-TTL II]. func.:0]. 5 SetSet[Wireless [Wireless func.] to [0]. 6 SetSet[Channel]. the channel (1-4) to the same one as the slave unit. Y P 7O C Set [Firing group:1All]. Set [Firing group] to [1All]. picture. 8 TakeSetthe the camera and take the picture in the same way as with normal flash shooting. To terminate wireless flash shooting, set [Wireless func.] to [Disable]. Setting [E-TTL II meter.] to [Evaluative] is recommended.
Using Wireless FlashN Fully Automatic Shooting with One External Speedlite and the Built-in Flash This is fully automatic wireless flash shooting with one external Speedlite and the built-in flash. You can change the flash ratio between the external Speedlite and built-in flash to adjust how the shadows look on the subject. 1 Y P O Set [Wireless func.] to [0:3]. C In step 5 on page 207, set [Wireless func.] to [0:3]. the desired flash ratio and 2 Set take the picture.
Using Wireless FlashN Fully Automatic Shooting with Multiple External Speedlites Multiple Speedlite slave units can be treated as one flash unit or separated into slave groups whose flash ratio can be set. The basic settings are shown below. By changing the [Firing group] setting, you can shoot with various wireless flash setups with multiple Speedlites. Basic settings: Flash mode : E-TTL II Wireless func.
Using Wireless FlashN [1 (A:B)] Multiple slave units in multiple groups A Divide the slave units into Groups A and B and change the flash ratio to obtain the desired lighting effect. Refer to your Speedlite’s instruction manual to set one slave unit’s slave ID to A (Group A) and the other slave unit’s ID to B (Group B) and position them as shown in the illustration. B 1 Y P O Set [Firing group] to [1 (A:B)]. C the desired flash ratio and 2 Set take the picture.
Using Wireless FlashN Fully Automatic Shooting with the Built-in Flash and Multiple External Speedlites The built-in flash can also be added to wireless flash shooting explained on pages 209-210. The basic settings are shown below. By changing the [Firing group] setting, you can shoot with various wireless flash setups of multiple Speedlites complemented with the built-in flash. 1 Basic settings: Flash mode : E-TTL II Wireless func. :0+3 Channel : (Same as slave units) Y P O [Firing group].
Using Wireless FlashN Creative Wireless Flash Shooting Flash exposure compensation When [Flash mode] is set to [E-TTL II], flash exposure compensation can be set. The flash exposure compensation settings that can be set (see below) will differ depending on the [Wireless func.] and [Firing group] settings. Flash exposure compensation The flash exposure compensation is applied to the built-in flash and all the external Speedlites. 2 exp. comp. The flash exposure compensation is applied to the built-in flash.
Using Wireless FlashN Setting the Flash Output Manually for Wireless Flash Shooting When [Flash mode] is set to [Manual flash], flash exposure can be set manually. The flash output settings that can be set ([1 flash output], [Group A output], etc.) will differ depending on the [Wireless func.] setting (see below). Wireless func.: 0 Firing group: 1All The manual flash output setting will be applied to all the external Speedlites.
MEMO C 214 Y P O
Shooting with the LCD Monitor (Live View Shooting) Y P O You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . C If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images. Using a tripod is recommended. To shoot while handholding the camera, see page 76.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. X The Live View image will appear on the LCD monitor. The Live View image will closely reflect the brightness level of the actual image you capture. the subject. 3 Focus When you press the shutter button Y P O halfway, the camera will focus with the current AF method (p.233). C the picture. 4 TakePress the shutter button completely.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [A1: Live View shoot.] to [Enable]. Number of Possible Shots with Live View Shooting [Approx. number of shots] Temperature Room Temperature (23°C / 73°F) Low Temperatures (0°C / 32°F) No Flash 230 210 50% Flash Use 210 200 The figures above are based on a fully-charged Battery Pack LP-E6 and CIPA (Camera & Imaging Products Association) testing standards.
A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change.
A Shooting with the LCD Monitor Do not hold the camera in the same position for long periods of time. Even if the camera does not feel too hot, prolonged contact with the same body part may cause skin redness, blistering or low-temperature contact burns. The use of a tripod is recommended for people with circulation problems or very sensitive skin, or when using the camera in very hot places. The histogram can be displayed when [A1: Expo. simulation: Enable] (p.230) is set.
A Shooting with the LCD Monitor Scene Icons In the shooting mode, the camera detects the scene type and sets everything automatically to suit the scene. The detected scene type is indicated on the upper left of the screen. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
A Shooting with the LCD Monitor *5: Displayed with any of the lenses below: • EF-S18-55mm f/3.5-5.6 IS II • EF-S55-250mm f/4-5.6 IS II • EF300mm f/2.8L IS II USM • EF400mm f/2.8L IS II USM • Image Stabilizer lenses marketed in 2012 or later. *4+*5:If the conditions in both *4 and *5 are met, the shutter speed will slow down.
Shooting Function Settings f / R / i / q / B Settings While the Live View image is displayed, if you press the , , , or button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function. When the Quick mode is set, you can press the button to select the AF area selection mode. With single-point AF (manual selection) and Zone AF, you can use <6>, <5>, or <9> to select an AF point or zone.
Shooting Function Settings Q Quick Control In Creative Zone modes, you can set the AF method, Drive mode, Metering mode, Image-recording quality, White balance, Picture Style, Auto Lighting Optimizer, and Creative Filters. In Basic Zone modes (except and ), you can set the functions in bold and the settings shown in the table on page 91. Press the button. (7) X The settable functions will be displayed. 1 a function and set it. 2 Select Press the key to select a C Y P O function.
U Shooting with Filter Effects While viewing the Live View image, you can apply a filter effect (Grainy B/W, Soft focus, Fish-eye effect, Art bold effect, Water painting effect, Toy camera effect, or Miniature effect) before shooting. These are called Creative filters. When you take the picture, the camera saves only the image with the Creative filter applied. If you also want to save the image without a Creative filter applied, take the picture without a Creative filter.
U Shooting with Filter Effects the filter effect. 5 Adjust Press the button (except for the Miniature effect). Press the key to adjust the filter effect, then press <0>. For the Miniature effect, press <0>, then press the key to move the white frame over the area you want the image look sharp. the picture. 6 Take X The image is shot with the filter applied. C Y P O When you set a Creative filter, single shooting will take effect even if the drive mode has been set to , , or .
U Shooting with Filter Effects Creative Filter Characteristics Grainy B/W Creates a grainy black-and-white photo. You can change the blackand-white effect by adjusting the contrast. Soft focus Gives the image a soft look. You can change the degree of softness by adjusting the blur. Fish-eye effect Gives the effect of a fish-eye lens. The image will have a barrel-type distortion. Depending on the level of this filter effect, the area trimmed along the periphery of the image changes.
U Shooting with Filter Effects Toy camera effect Darkens the photo’s corners and applies a color tone that makes it look as if it was shot by a toy camera. You can change the color cast by adjusting the color tone. Miniature effect Creates a diorama effect. You can change where the image looks sharp. In step 5, you can switch the horizontal/vertical orientation of the white frame by pressing the button (or tapping [ ] on the screen).
3 Menu Function Settings A1 When the Live View shooting/Movie shooting switch is set to , the Live View shooting menu options will appear under the [A1] and [A2] tabs. In Basic Zone modes, the [A2] tab and certain options under the [A1] tab will not appear. The settable functions on this menu screen apply only to Live View shooting. They do not work with viewfinder shooting (settings become invalid). Live View shooting You can set Live View shooting to [Enable] or [Disable].
3 Menu Function Settings Touch Shutter Just by tapping the LCD monitor screen, you can focus and take the picture automatically. For details, see page 245. Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you align the intersections over the subject for better balance in the composition.
3 Menu Function Settings The asterisked image-recording quality settings do not match the respective aspect ratio exactly. The image area displayed for the asterisked aspect ratio may be slightly different from the recorded area. Check the captured images on the LCD monitor when shooting. If you use a different camera to directly print images shot with this camera in the 1:1 aspect ratio, the images may not be correctly printed.
3 Menu Function Settings A2 N Silent LV shootingN • Mode 1 The shooting operation noise is quieter than with normal shooting. Continuous shooting is also possible. If is set, you can shoot at a maximum continuous shooting speed of approx. 7.0 fps. • Mode 2 When the shutter button is pressed completely, only one shot will be taken. While you keep holding down the shutter button, the camera operation will be suspended.
3 Menu Function Settings Metering timerN You can change how long the exposure setting is displayed (AE lock time). C Y P O Performing any of the following operations will stop Live View shooting. To start Live View shooting again, press the <0> button. • Selecting [z4: Dust Delete Data], [54: Sensor cleaning], [54: Clear all camera settings], or [54: z firmware ver.]. • Changing the shooting mode (example: Basic Zone modes ↔ Creative Zone modes).
Using AF to Focus (AF Method) Changes in AF Speed Depending On the AF Control Method If the AF method is set to [u+Tracking], [FlexiZone - Multi], or [FlexiZone - Single] for Live View shooting or movie shooting, the AF control method (phase-difference detection with the image sensor or contrast detection) will switch automatically depending on the lens used and functions selected, such as movie digital zoom or magnified view.
Using AF to Focus (AF Method) an AF point. 2 Select When a face is detected, the
frame will appear over the face to be focused. If multiple faces are detected, will be displayed. Use <9> to move the frame over the face you want to focus on. You can also tap the LCD monitor screen to select the face or subject. If the subject is not a face, < > will be displayed.
Using AF to Focus (AF Method) If the subject’s face is significantly out of focus, face detection will not be possible. You can prevent this by setting [Continuous AF] to [Enable]. An object other than a human face may be detected as a face. Face detection will not work if the face is very small or large in the picture, too bright or too dark, or partially hidden. The
may cover only part of the face.
Using AF to Focus (AF Method) FlexiZone - Multi:o You can focus over a wide area with up to 31 AF points (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection). 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. Area frame the AF point. N 2 Select Pressing <0> or the button Y P O will toggle between automatic selection and zone selection.
Using AF to Focus (AF Method) the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. X When focus is achieved, the AF point will turn green and the beeper will sound. X If focus is not achieved, the area frame will turn orange. the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.216).
Using AF to Focus (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus a particular subject. the Live View image. 1 Display Press the <0> button. AF point X The Live View image will appear on the LCD monitor. X The AF point < > will appear. During movie shooting, if [Movie Servo AF] is set to [Enable], the AF point will be displayed in a larger size. the AF point. 2 Move Use <9> to move the AF point to Y P O where you want to focus.
Using AF to Focus (AF Method) the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.216).
Using AF to Focus (AF Method) Notes for u+Tracking / FlexiZone - Multi / FlexiZone - Single AF Operation Even when focus has been achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult. If this happens, exit Live View shooting and autofocus under the actual light source.
Using AF to Focus (AF Method) Shooting Conditions that Make Focusing Difficult Low-contrast subjects such as the blue sky, solid-color flat surfaces or when highlight or shadow details are lost. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Subjects with repetitive patterns (skyscraper windows, computer keyboards, etc.). Fine lines and subject outlines. Under a light source whose brightness, color, or pattern keeps changing.
Using AF to Focus (AF Method) If you cannot achieve focus under the shooting conditions listed on the preceding page, set the lens focus mode switch to and focus manually. If you shoot a peripheral subject and it is slightly out of focus, aim the center AF point or zone over the subject to focus, focus again, and then take the picture. The AF-assist beam will not be emitted.
Using AF to Focus (AF Method) Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.100), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation. In AF area selection modes other than 19-point automatic selection AF, you can manually select the AF point. In Basic Zone modes, 19-point automatic selection AF is set automatically.
Using AF to Focus (AF Method) The AF point (or zone) selection will change in the direction you tilt <9>. If you press <0>, the center AF point (or center Zone) will be selected. You can also use the <6> and <5> dials to select the AF point. the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. X The Live View image will turn off, the reflex mirror will go back down, and AF will be executed. (No picture is taken.
x Shooting with the Touch Shutter Just by tapping the LCD monitor screen, you can focus and take the picture automatically. This works in all shooting modes. 1 Display the Live View image. Press the <0> button. X The Live View image will appear on the LCD monitor. the touch shutter. 2 Enable Tap [y] on the screen’s bottom left. C3 Each time you tap the icon, it will toggle between [y] and [x]. [x] (Touch shutter: Enable) You can focus and shoot by tapping the screen.
x Shooting with the Touch Shutter Even if , , or is set, single shooting will take effect. The touch shutter does not function during magnified view. When [V Shutter butt. half-press] is set to [Metering start] or [AE lock (while button pressed)] under [8 C.Fn III-4: Custom Controls], autofocusing does not take effect. You can also set the touch shutter with [A1: Touch shutter]. To take a bulb exposure, tap the screen twice. The first tap on the screen will start the bulb exposure.
MF: Focusing Manually You can magnify the image and focus precisely with manual focus. 1 Set the lens focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame. 2 Display Press the button. X The magnifying frame will appear. You can also tap [u] on the screen to magnify the image. Magnifying frame Y P O the magnifying frame. 3 Move Press <9> to move the magnifying C frame to the position where you want to focus. You can also tap it to move it.
MF: Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.216).
Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a prolonged period, the camera’s internal temperature may rise, and image quality may deteriorate. Always exit Live View shooting when you are not shooting.
Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. Even if a low ISO speed is set, noise may be noticeable in the displayed Live View image under low light. However, when you shoot, the image recorded will have minimal noise. (The image quality of the Live View image is different from that of the recorded image.) If the light source (illumination) within the image changes, the screen may flicker.
Shooting Movies Y P O Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . The movie recording format will be MOV. C For cards that can record movies, see page 3. If you handhold the camera and shoot movies, camera shake can cause blurred movies. Using a tripod is recommended. To shoot while handholding the camera, see page 76. If [53: Wi-Fi] is set to [Enable], movie shooting is not possible. Before shooting movies, set [Wi-Fi] to [Disable].
k Shooting Movies Autoexposure Shooting When the shooting mode is set to other than , autoexposure control will take effect to suit the scene’s current brightness. the shooting mode to a mode 1 Set other than . the Live View shooting/Movie 2 Set shooting switch to . X The reflex mirror will make a sound, then the image will appear on the LCD monitor. the subject. 3 Focus Before shooting a movie, focus with Y P O AF or manual focus (p.233-248).
k Shooting Movies In Basic Zone modes, the shooting result will be the same as in the mode. Also, the scene icon for the scene detected by the camera is displayed on the upper left of the screen (p.255). In the , , or shooting modes, the settings will be the same as in the mode. Settable menu functions will differ between Basic Zone modes and Creative Zone modes (p.415). In Creative Zone modes, you can press the button (p.170) to lock the exposure (AE lock).
k Shooting Movies ISO Speed in Basic Zone Modes The ISO speed will be set automatically within ISO 100 - ISO 6400. ISO Speed in the d, s, f, and F Mode The ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [12800/H] (p.123), the maximum ISO speed for the automatic ISO speed setting will be expanded to H (equivalent to ISO 12800).
k Shooting Movies Scene Icons During movie shooting in a Basic Zone mode, an icon representing the scene detected by the camera will be displayed and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. X The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. For details on the ISO speed, see the next page.
k Shooting Movies ISO Speed During Manual Exposure Shooting With [Auto] (A), the ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [12800/H] (p.123), the maximum ISO speed will be expanded and the ISO speed will be set automatically within ISO 100 to H (equivalent to ISO 12800). You can set the ISO speed manually within ISO 100 - ISO 6400 in 1/3-stop increments.
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies Notes on Movie Shooting Do not hold the camera in the same position for long periods of time. Even if the camera does not feel too hot, prolonged contact with the same body part may cause skin redness, blistering or low-temperature contact burns. The use of a tripod is recommended for people with circulation problems or very sensitive skin, or when using the camera in very hot places.
k Shooting Movies Notes on Movie Shooting You can use Remote Controller RC-6 (sold separately, p.184) to start and stop the movie shooting if the drive mode is or . Set the shooting timing switch to <2> (2-sec. delay), then press the transmit button. If the switch is set to (immediate shooting), still photo shooting will take effect. With a fully-charged Battery Pack LP-E6, the total movie shooting time will be approx. 1 hr. 20 min.
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking Still Photos during Movie Shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx. 1 sec. The captured still photo will be recorded to the card, and the movie shooting will resume automatically when the Live View image is displayed. The movie and still photo will be recorded as separate files on the card.
k Shooting Movies AEB cannot be used. Even if a flash is used, it will not fire. Continuous still photo shooting is possible during movie shooting. However, the captured images will not be displayed on the screen. Depending on the still photo’s image-recording quality, number of shots during continuous shooting, card performance, etc., movie shooting may stop automatically. When you press the
button to autofocus during movie shooting, the following phenomena may occur.
Shooting Function Settings f / R / i Settings While the movie image is displayed on the LCD monitor, if you press the or button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function. During manual exposure shooting (p.256), you can press the button to set the ISO speed. Note that metering mode cannot be set.
Shooting Function Settings Q Quick Control In Creative Zone modes, you can set the AF method, Drive mode, Movie recording size, Digital zoom, White balance, Picture Style, Auto Lighting Optimizer, and Video snapshots. In Basic Zone modes, only the functions in bold can be set. 1 Press the button. (7) X The settable functions will be displayed. Y P O a function and set it. 2 Select Press the key to select a function. X The selected function and Feature guide (p.69) will appear.
3 Setting the Movie Recording Size With [Z2: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image Size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9. B [1280x720] : High-Definition (HD) recording quality. The aspect ratio will be 16:9. C [640x480] : Standard-definition recording quality. The aspect ratio will be 4:3.
3 Setting the Movie Recording Size Total Movie Recording Time and File Size Per Minute Movie Recording Size Total Recording Time (approx.) File Size (approx.) 4 GB Card 8 GB Card 16 GB Card 654 X 16 min. 32 min. 1 hr. 4 min. 235 MB/min. 654 W 5 min. 11 min. 22 min. 685 MB/min. 87 X 18 min. 37 min. 1 hr. 14 min. 205 MB/min. 87 W 6 min. 12 min. 25 min. 610 MB/min. C 65 X 48 min. A B 1 hr. 37 min. 3 hr. 14 min. 78 MB/min.
3 Using Movie Digital Zoom When the movie size is [1920x1080] (Full HD), you can shoot with an approx. 3x to 10x digital zoom. 1 Select [Digital zoom]. Under the [Z2] tab, select [Digital zoom], then press <0>. [Approx. 3-10x zoom]. 2 Select Select [Approx. 3-10x zoom], then press <0>. Press the button to exit the menu and return to movie shooting. digital zoom. 3 UsePress the button. C Y P O X The digital zoom bar will appear. Press the key to zoom in or press the key to zoom out.
3 Setting the Sound Recording You can shoot movies while recording sound with the built-in stereo microphone or a commercially-available stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [Z2: Sound recording]. Sound Recording/Sound-Recording Level [Auto] : The sound-recording level is adjusted automatically. Auto level control will operate automatically in response to the sound level. [Manual] : For advanced users.
3 Setting the Sound Recording Using the Microphone The built-in microphone records stereo sound. Stereo sound recording is also possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (φ3.5 mm) to the camera’s external microphone IN terminal (p.20). C Y P O In Basic Zone modes, the settings available for [Sound recording] will be [On/Off].
3 Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Set the time code with [Z2: Time code]. Count Up [Rec run] : The time code counts up only while you are shooting a movie. [Free run] : The time code counts up whether you are shooting or not.
3 Setting the Time Code Movie Recording Count You can select what to display on the movie-shooting screen. [Rec time] : Indicates the elapsed time from the start of the movie shooting. [Time code] : Indicates the time code during movie shooting. Movie Playback Count You can select what to display on the movie playback screen. [Rec time] : Displays the recording time and playback time during movie playback. [Time code] : Displays the time code during movie playback.
3 Setting the Time Code Drop Frame If the frame rate setting is 6 (29.97 fps) or 8 (59.94 fps), the time code’s frame count causes a discrepancy between the actual time and time code. This discrepancy can be corrected automatically. This correction function is called drop frame. [Enable] : The discrepancy is corrected automatically by skipping time code numbers (DF: Drop frame). [Disable] : The discrepancy is not corrected (NDF: Non-drop frame).
3 Menu Function Settings Z1 When the Live View shooting/Movie shooting switch is set to , the [Z1] and [Z2] tabs dedicated to movie shooting will be displayed. AF method The AF methods are the same as described on pages 233-242. You can select [u+Tracking], [FlexiZone - Multi], or [FlexiZone Single]. For movie shooting, [Quick mode] cannot be set. Y P O Movie Servo AF During movie shooting, the camera focuses the subject continuously. The default setting is [Enable].
3 Menu Function Settings • If you want to keep the focus at a specific point or you do not want the lens operation noise to be recorded, you can temporarily stop Movie Servo AF as follows. When you stop Movie Servo AF, the AF point will turn gray. When you perform the same steps below, Movie Servo AF will resume. • Tap the [ ] icon on the lower left of the screen. • Press the button. • Under [8C.
3 Menu Function Settings Silent LV shootingN This function applies to still photo shooting. For details, see page 231. Metering timerN You can change how long the exposure setting is displayed (AE lock time).
3 Menu Function Settings Z2 Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you align the intersections over the subject for better balance in the composition. Y P O Movie recording size You can set the movie recording size (image size, frame rate, and compression method). For details, see page 265.
3 Shooting Video Snapshots A video snapshot is a short video clip lasting about 2 sec., 4 sec., or 8 sec. A series of video snapshots can be strung together to form a video snapshot album to show highlights of a trip, event, etc. A video snapshot album can also be played together with background music (p.284, 309). Video Snapshot Album Concept Video snapshot 1 Video snapshot 2 Video snapshot x Video snapshot album Y P O Setting the Video Snapshot Shooting Duration 1 Select [Video snapshot].
3 Shooting Video Snapshots [Album settings]. 3 Select Select [Album settings], then press <0>. [Create a new album]. 4 Select Select [Create a new album], then press <0>. the snapshot length. 5 Select Press <0> and use the key to Y P O select the snapshot’s length, then press <0>. C [OK]. 6 Select Select [OK], then press <0>. Shooting duration 278 Press the button to exit the menu. X A blue bar will appear to indicate the snapshot length. Go to “Creating a Video Snapshot Album” (p.279).
3 Shooting Video Snapshots Creating a Video Snapshot Album the first video snapshot. 7 Shoot Press the <0> button, then shoot. X The blue bar indicating the shooting duration will gradually decrease. After the set shooting duration elapses, the shooting stops automatically. X The confirmation dialog will appear (p.280). as a video snapshot album. 8 Save Select [J Save as album], then press <0>. X The movie clip will be saved as the video snapshot album’s first video snapshot.
3 Shooting Video Snapshots Options in Steps 8 and 9 Function Description JSave as album (Step 8) The movie clip will be saved as the video snapshot album’s first video snapshot. JAdd to album (Step 9) The video snapshot just shot will be added to the album recorded immediately before. W Save as a new album (Step 9) A new video snapshot album is created and the movie clip is saved as the first video snapshot. The new album will be a different file from the previously recorded album.
3 Shooting Video Snapshots [Playback video snapshot] Operations Function Playback Description 7 Play By pressing <0>, you can play or pause the justrecorded video snapshot. 5 First frame Displays the first scene of the album’s first video snapshot. Skip backward* Each time you press <0>, the video snapshot skips back by a few seconds. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie.
3 Shooting Video Snapshots Adding to an Existing Album 1 Select [Add to existing album]. Follow step 4 on page 278 to select [Add to existing album], then press <0>. an existing album. 2 Select Turn the <5> dial to select an existing album, then press <0>. Select [OK], then press <0>. X Certain video snapshot settings will change to match the existing album’s settings. Press the button to exit the menu. X The video snapshot shooting screen will appear. C Y P O the video snapshot.
3 Shooting Video Snapshots Cautions for Shooting Video Snapshots You can add to an album only video snapshots with the same duration (approx. 2 sec., 4 sec., or 8 sec. each). Note that if you do any of the following while shooting video snapshots, a new album will be created for subsequent video snapshots. • Changing the [Movie rec. size]. • Changing the [Sound rec.] setting from [Auto/Manual] to [Disable] or from [Disable] to [Auto/Manual]. • Updating the firmware.
3 Shooting Video Snapshots Playing an Album You can play a video snapshot album in the same way as a normal movie (p.308). 1 Play back the movie. Press the button to display an image. the album. 2 Select In the single-image display, the [ ] icon displayed on the upper left of the screen indicates a video snapshot album. Turn the <5> dial to select an album. C 3 Y P O Play back the album. Press <0>. On the movie playback panel displayed, select [7] (Play), then press <0>.
3 Shooting Video Snapshots Editing an Album After shooting, you can rearrange, delete, or play back the video snapshots in the album. 1 Select [X]. On the movie playback panel displayed, select [X] (Edit), then press <0>. X The editing screen will be displayed. an editing operation. 2 Select Select an editing option, then press <0>. Function C Y P O Description Move snapshot Press the key to select the video snapshot you want to move, then press <0>.
3 Shooting Video Snapshots the edited movie. 3 Save Press the button to return to the Editing panel at the screen’s bottom. Select [W] (Save), then press <0>. X The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite], then press <0>. C Y P O If the card does not have enough free space, [New file] will not be available. When the battery level is low, editing albums is not possible. Use a fullycharged battery.
Movie Shooting Cautions White and Red Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a white or red icon will appear. The white icon indicates that the image quality of still photos will deteriorate. You should stop still photo shooting and allow the camera’s internal temperature to cool before shooting again.
Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator becomes full, movie shooting Indicator will stop automatically.
Image Playback Y P O This chapter explains how to play back and erase photos and movies, how to display them on a TV screen, and other playback-related functions. C Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. X The last captured image or last image played back will appear. an image. 2 Select To play back images starting with the last image, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the display format will change.
x Image Playback the image playback. 3 ExitPress the button to exit the image playback and return to shooting-ready state. 3 Grid Display On the single-image display, you can overlay a playback grid. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag n]. This function is convenient for checking the image’s vertical or horizontal tilt, as well as composition. C Y P O The grid is not displayed during movie playback.
B: Shooting Information Display Sample Still Photo Taken in a Creative Zone Mode AF Microadjustment Exposure compensation amount Protect images Flash exposure compensation amount / HDR mode / Multi Shot Noise Reduction Rating Folder number - File number Aperture Histogram (Brightness/RGB) Shutter speed Picture Style/ Settings Metering mode Shooting mode/ Multiple exposure White balance Image-recording quality Playback number/ Total images recorded Color temperature when
is set C Y P O ISO spee
B: Shooting Information Display Sample Still Photo Taken in a Basic Zone Mode Ambience and ambience effects Shooting mode Lighting or scene * With images taken in a Basic Zone mode, the information displayed will differ depending on the shooting mode. * [Background blur] will be displayed for images taken in the mode.
B: Shooting Information Display Highlight Alert When [33: Highlight alert] is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed, blinking areas, set the exposure compensation to a negative amount and shoot again. AF Point Display When [33: AF point disp.] is set to [Enable], the AF point that achieved focus will be displayed in red. If automatic AF point selection was used, multiple AF points may be displayed at the same time.
B: Shooting Information Display Histogram The brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram is for checking the color saturation and gradation. The display can be switched with [33: Histogram disp.]. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing four or nine images on one screen. 1 Î Switch to the index display. During image playback, press the button. X The 4-image index display will appear. The selected image is highlighted in an orange frame. Press the button again to switch to the 9-image display. Pressing the button will switch the display from 9 images to 4 images and then to 1 image.
x Searching for Images Quickly I Jump through Images (Jump Display) In the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. 1 Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>. the jump method. 2 Select Turn the <5> dial to select the jump method, then press <0>.
u/y Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. 1 Magnify the image. Press the button during image playback. X The image will be magnified. If you hold down the button, the image will be magnified until it reaches the maximum magnification. Press the button to reduce the magnification. If you hold down the button, the magnification will be reduced to the single-image display. Magnified area position Y P O around the image.
d Playing Back with the Touch Screen The LCD monitor is a touch-sensitive panel that you can touch with your fingers for various playback operations. First, press the button to play back images. Browsing Images Swipe with one finger. C With single-image display, touch the LCD monitor with one finger. You can browse to the next or previous image by swiping your finger to the left or right. Swipe left to see the next (newer) images or swipe right to see previous (older) images.
d Playing Back with the Touch Screen Reducing Image (Index Display) Pinch two fingers. Touch the screen with two fingers spread apart, then pinch your fingers together on the screen. Each time you pinch your fingers, the screen changes from a single-image display to a 4-image index display and 9-image index display. If you spread your fingers, the image display will change in the reverse order. When you select an image, the orange frame will appear. Tap the image again to display it as a single image.
b Rotating the Image You can rotate the displayed image to the desired orientation. 1 Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. an image. 2 Select Turn the <5> dial to select the image to be rotated. You can also select an image in the index display (p.296). Y P O the image. 3 Rotate Each time you press <0>, the C image will rotate clockwise as follows: 90° 9 270° 9 0°. To rotate another image, repeat steps 2 and 3. To return to the menu, press the button.
3 Setting Ratings You can rate images (still photos and movies) with one of five rating marks: l/m/n/o/p. This function is called rating. 1 Select [Rating]. Under the [32] tab, select [Rating], then press <0>. an image. 2 Select Turn the <5> dial to select the image or movie to be rated. To display the three-image display, press the button. To return to the single-image display, press the button. Y P O the image. 3 RatePress the key to select a C rating.
3 Setting Ratings The total number of images with a given rating that can be displayed is up to 999. If there are more than 999 images with a given rating, [###] will be displayed for that rating. Taking Advantage of Ratings With [32: Image jump w/6], you can display only images with a specific rating. With [32: Slide show], you can play back only images with a specific rating. With Digital Photo Professional (provided software, p.456), you can select only images with a specific rating (still photos only).
Q Quick Control for Playback During single-image display, you can press the button to set any of the following: [J: Protect images, b: Rotate image, 9: Rating, U: Creative filters, S: Resize (JPEG image only), : Highlight alert, : AF point display, e: Image jump w/6, k: Wi-Fi*]. For movies, only the functions in bold above can be set. * Not selectable if [53: Wi-Fi] is set to [Disable]. 1 Press the button. During image playback, press the button. X The Quick Control options will appear.
Q Quick Control for Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the button during the index display will switch to the single-image display and the Quick Control screen will appear. Pressing the button again will return to the index display.
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV Set (p.316, 319) Use the HDMI cable HTC-100 (sold separately) or stereo AV cable AVCDC400ST (sold separately) to connect the camera to a TV set. Then you can play back captured movies and still photos on TV. If you have a High-Definition TV set and connect your camera with an HDMI cable, you can watch Full High-Definition (Full HD: 1920x1080) and HighDefinition (HD: 1280x720) movies with higher image quality.
k Enjoying Movies Playback and Editing with a Computer (p.456) The movie files recorded on the card can be transferred to a computer and played with ImageBrowser EX (provided software). To have the movie play back smoothly on a computer, use a highperformance computer. Regarding the computer hardware requirements for ImageBrowser EX, refer to the PDF file ImageBrowser EX User Guide. If you want to use commercially-available software to play back or edit the movies, be sure it is compatible with MOV files.
k Playing Movies 1 Play back the image. Press the button to display an image. a movie. 2 Select Turn the <5> dial to select the movie to be played. In the single-image display, the icon displayed on the upper left of the screen indicates a movie. If the movie is a video snapshot, < > will be displayed. In the index display, perforations at the left edge of a thumbnail indicate a movie. As movies cannot be played from the index display, press <0> to switch to the single-image display.
k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by pressing the key. The slow motion speed is indicated at the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie. 6 Next frame Each time you press <0>, the movie will play frame-byframe.
X Editing a Movie’s First and Last Scenes Playback with the Touch Screen Tap [7] at the center of the screen. X The movie will start playing. To display the movie playback panel, tap on the upper left of the screen. To pause the movie while it is playing, tap the screen. The movie playback panel will also appear. X Editing a Movie’s First and Last Scenes Y P O You can edit out the first and last scenes of a movie in approx. 1-sec. increments. 1 On the movie playback screen, select [X].
X Editing a Movie’s First and Last Scenes the edited movie. 3 Check Select [7] and press <0> to play back the edited movie. To change the editing, go back to step 2. To cancel the editing, press the button, then select [OK] on the confirmation screen. the edited movie. 4 Save Select [W], then press <0>. C X The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite], then press <0>.
3 Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. 1 Number of images to be played Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. the images to be played. 2 Select Press the key to select the desired option, then press <0>. [All images]/[Movies]/[Stills] Press the key to select one of the following: [jAll images]/ [kMovies]/[zStills]. Then press <0>.
3 Slide Show (Auto Playback) Item Playback Description jAll images All the still photos and movies on the card will be played back. iDate Still photos and movies taken on the selected shooting date will be played back. nFolder Still photos and movies in the selected folder will be played back. kMovies Only the movies on the card will be played back. zStills Only the still photos on the card will be played back.
3 Slide Show (Auto Playback) [Transition effect] [Background music] the slide show. 4 StartPress the key to select [Start], then press <0>. X After [Loading image...] is displayed, the slide show will start. Y P O slide show. 5 ExitTothe exit the slide show and return to the setting screen, press the button. C To pause the slide show, press <0>. During pause, [G] will be displayed on the upper left of the image. Press <0> again to resume the slide show.
3 Slide Show (Auto Playback) Selecting the Background Music After you use EOS Utility (provided software) to copy background music to the card, you can play background music together with the slide show. 1 Select [Background music]. Set [Background music] to [On], then press <0>. If the card has no background music, you cannot perform step 2. the background music. 2 Select Press the key to select the Y P 3O C desired background music, then press <0>.
Viewing Images on a TV Set You can view still photos and movies on a TV set. Viewing on High-Definition (HD) TV Sets (Connected with HDMI) HDMI Cable HTC-100 (sold separately) is required. 1 Connect the HDMI cable to the camera. With the plug’s logo facing the front of the camera, insert it into the terminal. the HDMI cable to the TV 2 Connect set. Y P O Connect the HDMI cable to the TV’s HDMI IN port. C on the TV and switch the 3 Turn TV’s video input to select the connected port.
Viewing Images on a TV Set the button. 5 Press X The image will appear on the TV screen. (Nothing will be displayed on the camera’s LCD monitor.) The images will automatically be displayed at the TV’s optimum resolution. By pressing the button, you can change the display format. To play back movies, see page 308. The images cannot be output at the same time from both the and terminals. Y P O Do not connect any other device’s output to the camera’s terminal.
Viewing Images on a TV Set the camera to a TV set. 2 Connect Use an HDMI cable to connect the camera to the TV. X The TV’s input will switch automatically to the HDMI port connected to the camera. the camera’s button. 3 Press X An image will appear on the TV screen and you can use the TV’s remote control to play back images. an image. 4 Select Point the remote control toward the TV set and press the / button to select an image.
Viewing Images on a TV Set Viewing on Non-HD TV Sets (Connected with AV Cable) Stereo AV Cable AVC-DC400ST (sold separately) is required. 1 Connect the AV cable to the camera. With the plug’s logo facing the back of the camera, insert it into the terminal. the AV cable to the TV 2 Connect set. (Red) (White) AUDIO (Yellow) VIDEO Connect the AV cable to the TV’s video IN terminal and audio IN terminals.
K Protecting Images Protecting an image prevents it from being erased accidentally. 3 Protecting a Single Image 1 Select [Protect images]. Under the [31] tab, select [Protect images], then press <0>. [Select images]. 2 Select Select [Select images], then press <0>. X An image will be displayed. Image protect icon 320 3 Y P O Protect the image. C Turn the <5> dial to select the image to be protected, then press <0>.
K Protecting Images 3 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at one time. When you select [All images in folder] or [All images on card] in [31: Protect images], all the images in the folder or on the card will be protected. To cancel the image protection, select [Unprotect all images in folder] or [Unprotect all images on card]. C Y P O If you format the card (p.57), the protected images will also be erased. Movies can also be protected.
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images (p.320) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button.
L Erasing Images [Select and erase images]. 2 Select Select [Select and erase images], then press <0>. X An image will be displayed. To display the three-image display, press the button. To return to the single-image display, press the button. the images to be erased. 3 Select Turn the <5> dial to select the image to be erased, then press <0>. X A checkmark will be displayed on the upper left of the screen. To select other images to be erased, repeat step 3. Y P 4O C Erase the image.
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. 1 Select [LCD brightness]. 2 Adjust the brightness. Under the [52] tab, select [LCD brightness], then press <0>. While referring to the gray chart, press the key, then press <0>. C Y P O To check the image’s exposure, looking at the histogram is recommended (p.295).
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the computer instead of horizontally. You can change the setting for this feature. 1 Select [Auto rotate]. Under the [51] tab, select [Auto rotate], then press <0>. the auto rotation. 2 SetSelect the desired setting, then press Y P O <0>.
MEMO C 326 Y P O
Post-Processing Images Y P O You can process RAW images with the camera, resize (reduce the pixel count of) JPEG images, and apply Creative filters. C The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). The camera may not be able to process images taken with another camera.
R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. While the RAW image itself does not change, you can process the RAW image according to different conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera. Use Digital Photo Professional (provided software, p.456) to process those images. 1 Select [RAW image processing].
R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the setting screen. Turn the <5> or <6> dial to change the setting. To finalize the change and return to the screen in step 3, press <0>. the image. 4 Save Select [W] (Save), then press <0>. Select [OK] to save the image. Check the destination folder and image file number, then select [OK]. To process another image, repeat steps 2 to 4. Y P O To return to the menu, press the button.
R Processing RAW Images with the CameraN RAW Image Processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. Picture Style (p.126) You can select the Picture Style. Press the key to select the Picture Style. To set the parameters such as sharpness, press the button to display the setting screen. Press the key to select a parameter to be adjusted, then press the key to change it.
R Processing RAW Images with the CameraN Color space (p.155) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.146) If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, magnify the image (p.329) and check the four corners.
R Processing RAW Images with the CameraN Peripheral Illumination Correction, Distortion Correction, and Chromatic Aberration Correction To execute peripheral illumination correction, distortion correction, and chromatic aberration correction with the camera, the data of the lens used for the shot must be registered in the camera. If the lens data has not been registered in the camera, use EOS Utility (provided software, p.456) to register the lens data.
S Resizing JPEG Images You can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/4/a/b images. JPEG c and RAW images cannot be resized. 1 Select [Resize]. Under the [32] tab, select [Resize], then press <0>. X An image will be displayed. an image. 2 Select Turn the <5> dial to select the image you want to resize. By pressing the button, you can switch to the index display and select an image. Y P O the desired image size.
S Resizing JPEG Images Resize Options According to Original Image Size Available Resize Settings Original Image Size 4 a b 3 k k k k k k k k k 4 a c k b Image Sizes The image size displayed in step 3 on the preceding page, such as [***M ****x****], has a 3:2 aspect ratio. The image size according to aspect ratios is shown in the table below. The asterisked image-recording quality figures do not exactly match the aspect ratio. The image will be cropped slightly.
U Applying Creative Filters You can apply the following Creative filters to an image and save it as a new image: Grainy B/W, Soft focus, Fish-eye effect, Art bold effect, Water painting effect, Toy camera effect, and Miniature effect. 1 Select [Creative filters]. Under the [x1] tab, select [Creative filters], then press <0>. X An image will be displayed. an image. 2 Select Turn the <5> dial to select the image you want to apply a filter to.
U Applying Creative Filters the image. 5 Save Select [OK] to save the image. Check the destination folder and image file number, then select [OK]. To apply a filter to another image, repeat steps 2 to 5. To return to the menu, press the button. When shooting 1+JPEG images, the Creative filter will be applied to the 1 image and the image will be saved as a JPEG image. When shooting 41+JPEG or 61+JPEG images, the Creative filter will be applied to the JPEG image.
U Applying Creative Filters Fish-eye effect Gives the effect of a fish-eye lens. The image will have a barrel-type distortion. Depending on the level of this filter effect, the area trimmed along the periphery of the image changes. Also, since this filter effect will magnify the image center, the apparent resolution at the center may degrade depending on the number of recorded pixels. Set the filter effect in step 4 while checking the resulting image.
MEMO C 338 Y P O
Sensor Cleaning Y P O The camera has a Self Cleaning Sensor Unit to automatically shake off dust adhered to the image sensor’s front layer (low pass filter). The Dust Delete Data can also be appended to the image so that the dust spots remaining can be erased automatically by Digital Photo Professional (provided software, p.456).
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation. However, you can choose to perform sensor cleaning at any time, or disable it. Cleaning the Sensor Now 1 Select [Sensor cleaning]. Under the [54] tab, select [Sensor cleaning], then press <0>. [Clean nowf]. 2 Select Select [Clean nowf], then press Y P O <0>.
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later. The Dust Delete Data is used by Digital Photo Professional (provided software, p.456) to erase the dust spots automatically. Preparation Prepare a solid white object such as a sheet of paper. Set the lens focal length to 50 mm or longer.
3 Appending Dust Delete DataN a solid-white object. 3 Shoot At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. X The picture will be taken in aperturepriority AE mode at an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no card in the camera. X When the picture is taken, the camera will start collecting the Dust Delete Data.
3 Manual Sensor CleaningN Dust that could not be removed by the automatic sensor cleaning can be removed manually with a commercially-available blower, etc. Before cleaning the sensor, detach the lens from the camera. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. 1 Select [Sensor cleaning]. Under the [54] tab, select [Sensor cleaning], then press <0>. [Clean manually].
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. If the power is cut off, the shutter will close and the shutter curtains and image sensor may get damaged. • Setting the power switch to <2>. • Removing or inserting the battery. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor. Do not insert the blower tip inside the camera beyond the lens mount.
12 Printing Images Y P O Printing (p.348) You can connect the camera directly to a printer and print out the images on the card. The camera is compatible with “wPictBridge”, which is the standard for direct printing. You can also use a wireless LAN to send images to a PictBridge (Wireless LAN) printer and print them. For details, refer to the Wi-Fi Function Instruction Manual. C Digital Print Order Format (DPOF) (p.
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor. Connecting the Camera to a Printer 1 Set the camera’s power switch to <2>. the printer. 2 SetForupdetails, refer to the printer’s instruction manual. 3 Y P O Connect the Camera to the Printer. Use the interface cable provided with the camera. Connect the cable to the camera’s terminal with the cable plug’s icon facing the front of the camera.
Preparing to Print wPictBridge back the image. 6 PlayPress the button. X The image will appear, with the icon on the upper left of the screen to indicate that the camera is connected to a printer. C Y P O Make sure the printer has a PictBridge connection port. Movies cannot be printed. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct. Do not use any interface cable other than the one provided.
w Printing The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon 1 Select the image to be printed. Check that the icon is displayed on the upper left of the LCD monitor. Turn the <5> dial to select the image to be printed. <0>. 2 Press X The print setting screen will appear. Print setting screen Sets the printing effects (p.350).
w Printing Q Setting the Paper Size Select the size of the paper loaded in the printer, then press <0>. X The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in the printer, then press <0>. X The page layout screen will appear. U Setting the Page Layout Y P O Select the page layout, then press <0>. X The print setting screen will reappear. C Bordered The print will have white borders along the edges. Borderless The print will have no borders.
w Printing effects. 4 SetSetthethemprinting if necessary. If you do not need to set any printing effects, go to step 5. What is displayed on the screen differs depending on the printer. Select the option, then press <0>. Select the desired printing effect, then press <0>. If the and icons are displayed brightly, you can also adjust the printing effect (p.352). Printing Effect Description EOn The image will be printed using the printer’s standard colors.
w Printing the date and file number 5 Set imprinting. Set them if necessary. Select , then press <0>. Set the print settings as desired, then press <0>. of copies. 6 SetSettheit ifnumber necessary. Select , then press <0>. Select the number of copies, then press <0>. printing. 7 StartSelect [Print], then press <0>. C Y P O The [Default] setting for printing effects and other options are the printer’s own default settings as set by the printer’s manufacturer.
w Printing e Adjustment of Printing Effects In step 4 on page 350, select the printing effect. When the icon is displayed brightly next to , you can press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels When you select [Manual], you can change the histogram’s distribution and adjust the image’s brightness and contrast.
w Printing Cropping the Image Tilt correction You can crop the image and print only an enlarged version of the cropped portion, as if the image had been recomposed. Set the cropping right before printing. If you change the print settings after setting the cropping, you may have to set the cropping again before printing. 1 On the print setting screen, select [Cropping]. 2 Set the cropping frame size, position, and aspect ratio. Y P O The image area within the cropping frame will be printed.
w Printing Depending on the printer, the cropped image area may not be printed as you specified. The smaller you make the cropping frame, the grainier the picture will look in the print. While cropping the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the cropping frame may not be displayed accurately. Handling Printer Errors If you resolve a printer error (no ink, no paper, etc.
W Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options 1 Select [Print order]. Under the [31] tab, select [Print order], then press <0>. [Set up]. 2 Select Select [Set up], then press <0>. C3 Y P O Set the option as desired. [Print type] Set the [Print type], [Date], and [File No.].
W Digital Print Order Format (DPOF) Print type Date File number K Standard Prints one image on one sheet. L Index Multiple thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date on the print. [On] imprints the file number on the print. 4 Exit the setting. Press the button. X The print order screen will reappear. Y P O Next, select [Sel.Image], [Byn], or [All image] to order the images to be printed.
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. To display the three-image display, press the button. To return to the single-image display, press the button. Press the button to save the print order to the card. Quantity Total images selected Checkmark Index icon [Standard] [Both] Press the key to set the number of copies to be printed for the displayed image. Y P O [Index] Press <0> to add a checkmark to the box .
W Direct Printing of Print-Ordered Images With a PictBridge printer, you can easily print images with DPOF. 1 Prepare to print. See page 346. Follow the “Connecting the Camera to a Printer” procedure up to step 5. 2 Under the [31] tab, select [Print order]. 3 Select [Print]. Y P O [Print] will be displayed only if the camera is connected to a printer and printing is possible. 4 Set the [Paper settings] (p.348). C Set the printing effects (p.350) if necessary. 5 Select [OK].
p Specifying Images for a Photobook When you select images to use in photobooks (up to 998 images) and use EOS Utility (provided software) to transfer them to a computer, the selected images will be copied into a dedicated folder. This function is useful for ordering photobooks online. Specifying One Image at a Time 1 Select [Photobook Set-up]. Under the [x1] tab, select [Photobook Set-up], then press <0>. [Select images]. 2 Select Select [Select images], then press C Y P O <0>.
p Specifying Images for a Photobook Specifying All Images in a Folder or on a Card You can specify all the images in a folder or on a card at one time. When [x1: Photobook Set-up] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be specified. To cancel the image specification, select [Clear all in folder] or [Clear all on card].
Customizing the Camera Y P O You can customize various camera functions to suit your picture-taking preferences with Custom Functions. Also, the current camera settings can be saved under the Mode Dial position. The functions explained in this chapter work only in the Creative Zone modes.
3 Setting Custom FunctionsN 1 Select [8]. the group. 2 Select Select C.Fn I, II, or III, then press <0>. Custom Function number the Custom Function 3 Select number. Press the key to select the Custom Function number, then press <0>. the setting as desired. 4 Change Select the desired setting (number), Y P O then press <0>. Repeat steps 2 to 4 if you want to set other Custom Functions.
3 Custom FunctionsN 1 Exposure level increments p.365 A LV Shooting k 2 ISO speed setting increments p.365 k C.Fn I: Exposure 3 Bracketing auto cancel p.365 k 4 Bracketing sequence p.366 k 5 Number of bracketed shots p.366 k 6 Safety shift p.367 k k Movie Shooting In a k (Still photo, with WB bracketing) C.Fn II: Autofocus 1 Tracking sensitivity p.368 2 Acceleration/deceleration tracking p.369 Y P O 3 AI Servo 1st image priority 4 AI Servo 2nd image priority p.
3 Custom FunctionsN C.Fn III: Operation/Others 1 Dial direction during Tv/Av p.375 k k 2 Multi function lock p.375 k k 3 Warnings z in viewfinder p.376 4 Custom Controls p.
3 Custom Function SettingsN C.Fn I: Exposure C.Fn I -1 Exposure level increments 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. This is effective when you prefer to control the exposure in less fine increments than 1/3stop increments. With setting 1, the exposure level will be displayed in the viewfinder and on the LCD panel as shown below. C.Fn I -2 0: 1/3-stop 1: 1-stop C.
3 Custom Function SettingsN C.Fn I -4 Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0: 09-9+ 1: -909+ 2: +909White Balance Bracketing B/A Direction M/G Direction 0 : Standard exposure 0 : Standard white balance 0 : Standard white balance - : Decreased exposure - : Blue bias - : Magenta bias + : Increased exposure + : Amber bias + : Green bias AEB C.
3 Custom Function SettingsN C.Fn I -6 Safety shift 0: Disable 1: Shutter speed/Aperture This takes effect in the shutter-priority AE (s) and aperture-priority AE (f) modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure. 2: ISO speed This works in the Program AE (d), shutter-priority AE (s), and aperturepriority AE (f) modes.
3 Custom Function SettingsN C.Fn II: Autofocus C.Fn II -1 Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. 0: Default setting suited for most subjects. Suited for normal, moving subjects. Locked on: -2 / Locked on: -1 The camera will try to continue focusing the subject even if an obstacle enters the AF points or if the subject strays from the AF points.
3 Custom Function SettingsN C.Fn II -2 Acceleration/deceleration tracking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly, etc. 0: Suited for subjects that move at a fixed speed. +2 / +1: Effective for subjects having sudden movements, sudden acceleration/ deceleration, or sudden stops. Even if the moving subject’s speed suddenly changes dramatically, the camera continues to focus the target subject.
3 Custom Function SettingsN C.Fn II -4 AI Servo 2nd image priority You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF. Equal priority: Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, shooting speed may slow down. : Shooting speed priority Priority is given to the continuous shooting speed instead of achieving focus.
3 Custom Function SettingsN C.Fn II -5 AF-assist beam firing Enables or disables the AF-assist beam emitted by the built-in flash or EOSdedicated external Speedlite. 0: Enable The AF-assist beam will be emitted when necessary. 1: Disable The AF-assist beam is not emitted. This prevents the AF-assist beam from disturbing others. 2: Enable external flash only The AF-assist beam will be emitted when necessary only if an external Speedlite is used.
3 Custom Function SettingsN C.Fn II -7 Select AF area selection mode You can limit the selectable AF area selection modes to suit your shooting preferences. Select the mode you want to use, then press <0> to append a checkmark and select [OK]. : Manual selection: 1 pt AF You can select one AF point. : Manual select.: Zone AF The 19 AF points are divided into five zones for focusing. : Auto selection: 19 pt AF All of the AF points are used for focusing.
3 Custom Function SettingsN C.Fn II -9 Orientation linked AF point You can set the AF area selection mode and manually-selected AF point separately for vertical shooting and horizontal shooting. 0: Same for both vertical/horizontal The same AF area selection mode and manually-selected AF point (or zone) are used for both vertical shooting and horizontal shooting.
3 Custom Function SettingsN C.Fn II -11 AF point display during focus You can set whether or not to display the AF point(s) in the following cases: 1. When selecting the AF point(s), 2. When the camera is ready to shoot (before AF operation), 3. During AF operation, and 4. When focus is achieved. 0: Selected (constant) The selected AF point(s) is always displayed. 1: All (constant) All 19 AF points are always displayed.
3 Custom Function SettingsN C.Fn II -13 AF Microadjustment Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. For details, see page 377. C.Fn III: Operation/Others C.Fn III -1 Dial direction during Tv/Av 0: Normal 1: Reverse direction The dial’s turning direction for setting the shutter speed and aperture can be reversed. In the shooting mode, the turning direction of the <6> and <5> dials will be reversed.
3 Custom Function SettingsN C.Fn III -3 Warnings z in viewfinder When any of the following functions are set, the icon can be displayed on the viewfinder’s bottom right (p.23). The icon will also appear on the shooting function settings display (p.49). Select the function for which you want the warning icon to appear, press <0> to append a , then select [OK]. When monochrome V is set: If the Picture Style is set to [Monochrome] (p.127), the warning icon will appear.
8: Fine Adjustment of AF’s Point of Focus Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. This is called “AF Microadjustment”. Before making the adjustment, read “Notes for AF Microadjustment” on page 382. Normally, this adjustment is not required. Perform this adjustment only if necessary. Note that performing this adjustment may prevent correct focusing from being achieved.
8: Fine Adjustment of AF’s Point of Focus the adjustment. 5 Make Press the key to make the adjustment. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to the rear of the standard point of focus. After making the adjustment, press <0>. Select [1: All by same amount], then press <0>. Press the button to exit. Y P O the result of the 6 Check adjustment.
8: Fine Adjustment of AF’s Point of Focus 2: Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment has been registered, the point of focus will always be shifted by the adjustment amount. Set the adjustment manually by adjusting, shooting, and checking the result. If you use a zoom lens, make the adjustment for the wide-angle (W) and telephoto (T) ends.
8: Fine Adjustment of AF’s Point of Focus Enter the serial number. Press the key to select the digit to be entered, then press <0> to display . Press the key to enter the number, then press <0>. After entering all the digits, select [OK] and press <0>. Lens Serial Number In step 3, if “ * ” appears in front of the 10-digit lens serial number, you cannot register several units of the same lens model. Even if you enter the serial number, “ * ” will remain displayed.
8: Fine Adjustment of AF’s Point of Focus Single focal length lens the adjustment. 4 Make For a zoom lens, press the key Zoom lens C and select the wide-angle (W) or telephoto (T) end. Press <0> and the box will disappear, allowing you to make the adjustment. Press the key to adjust as desired, then press <0>. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus.
8: Fine Adjustment of AF’s Point of Focus When shooting with the intermediate range (focal length) of a zoom lens, the AF’s point of focus is corrected automatically relative to the adjustments made for the wide-angle and telephoto ends. Even if only the wide-angle or telephoto end has been adjusted, a correction will be made automatically for the intermediate range.
8: Custom Controls You can assign often-used functions to camera buttons or dials according to your preferences. 1 Select [C.Fn III: Operation/ Others]. Under the [8] tab, select [C.Fn III: Operation/Others], then press <0>. [4: Custom Controls]. 2 Select Select [4: Custom Controls], then press <0>. X The Custom Controls screen will appear. Y P O a camera button or dial. 3 Select Select a camera button or dial, then C press <0>.
8: Custom Controls Assignable Functions to Camera Controls Function Page k Metering and AF start AF AF stop 386 ONE SHOT z AI SERVO k k k k k k k k k k k k k k AF point direct selection Metering start 386 AE lock/FE lock k AE lock k AE lock (while button pressed) Exposure AE lock (hold) FE lock 387 Y P O Set ISO speed (hold button, turn ) Shutter speed setting in M mode Aperture setting in M mode External flash Images C Flash exposure compensation Image quality Picture Styl
8: Custom Controls * k k k k k k k k k k k k k k k k k k k Y P O k C k k k k k k k k k * The AF stop button ( k ) is provided only on super telephoto IS lenses.
8: Custom Controls : Metering and AF start When you press the button assigned to this function, metering and AF are executed. : AF stop The AF will stop while you hold down the button assigned to this function. Convenient when you want to lock the focus during AI Servo AF. : ONE SHOT z AI SERVO You can switch the AF operation. In One-Shot AF mode, when you hold down the button to which this function is assigned, the camera switches to AI Servo AF mode.
8: Custom Controls : AE lock When you press the button assigned to this function, you can lock the exposure (AE lock) during the metering. Convenient when you want to focus and meter the shot at different areas or when you want to take multiple shots at the same exposure setting. : AE lock (while button pressed) The exposure will be locked (AE lock) while you press the shutter button. : AE lock (hold) When you press the button assigned to this function, you can lock the exposure (AE lock).
8: Custom Controls : Flash exposure compensation Press <0> to display the flash exposure compensation setting screen (p.190) on the LCD monitor. : Image quality Press <0> to display the image-recording quality setting screen (p.116) on the LCD monitor. : Picture Style Press <0> to display the Picture Style selection setting screen (p.126) on the LCD monitor. : Depth-of-field preview When you press the depth-of-field preview button, the aperture will stop down and you can check the depth of field (p.
3 Registering My MenuN Under the My Menu tab, you can register up to six menu options and Custom Functions whose settings you change frequently. 1 Select [My Menu settings]. Under the [9] tab, select [My Menu settings], then press <0>. [Register to My Menu]. 2 Select Select [Register to My Menu], then press <0>. the desired items. 3 Register Select the item, then press <0>. My Menu Settings C Y P O Select [OK] and press <0> to register the item. You can register up to six items.
w: Register Custom Shooting ModesN You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial position. 1 Select [Custom shooting mode (C mode)]. Under the [54] tab, select [Custom shooting mode (C mode)], then press <0>. [Register settings]. 2 Select Select [Register settings], then press <0>. Y P O the Custom shooting 3 Register mode. Select [OK], then press <0>. X The current camera settings (p.
w: Register Custom Shooting ModesN Settings Registered Shooting Function Settings Shooting mode, Shutter speed, Aperture, ISO speed, Exposure compensation, Flash exposure compensation, AF operation, AF point, Drive mode, Metering mode. Menu functions z1 Image quality, VF grid display l, Viewfinder level, Beep, Release shutter without card, Image review z2 Lens aberration correction (Peripheral illumination, Chromatic aberration), Flash control, E-TTL II metering, Flash sync.
w: Register Custom Shooting ModesN C.Fn I: Exposure Exposure level increments, ISO speed setting increments, Bracketing auto cancel, Bracketing sequence, Number of bracketed shots, Safety shift C.
Reference Y P O This chapter provides reference information for camera features, system accessories, etc. C Certification Logo Select [54: Certification Logo Display] and press <0> to display some of the logos of the camera’s certifications. Other certification logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.
B Button Functions When you press the button while the camera is ready to shoot, you can display [Displays camera settings], [Electronic level] (p.65), and [Displays shooting functions] (p.395). Under the [53] tab, [z button display options] enables you to select the options displayed when the button is pressed. Select the desired display option and press <0> to append a checkmark . After making the selection, select [OK], then press <0>.
B Button Functions Shooting Function Settings White balance correction Shutter speed Shooting mode Aperture AE lock Flash exposure compensation ISO speed Highlight tone priority Exposure level indicator Wi-Fi function Picture Style Custom Controls AF operation Image-recording quality Quick Control icon Possible shots Battery check White balance AF point selection Eye-Fi card transmission status C Max.
3 Checking the Battery Information You can check the battery’s condition on the LCD monitor. Each Battery Pack LP-E6 has a unique serial number, and you can register multiple battery packs to the camera. When you use this feature, you can check the registered battery pack’s remaining capacity and operation history. Select [Battery info.]. Under the [54] tab, select [Battery info.], then press <0>. X The battery info screen will appear. Battery position Battery model or household power source being used.
3 Checking the Battery Information Registering the Battery to the Camera You can register up to six LP-E6 battery packs to the camera. To register multiple battery packs to the camera, do the procedure below for each battery pack. 1 Press the button. With the battery info. screen displayed, press the button. X The battery history screen will appear. X If the battery has not been registered, it will be grayed out. [Register]. 2 Select Select [Register], then press <0>.
3 Checking the Battery Information Labeling the Serial Number on the Battery It is convenient to label all registered Battery Pack LP-E6 with their serial numbers, using commercially available labels. Serial number 1 Write the serial number on a label. Write the serial number displayed on the battery history screen on a label approx. 25 mm x 15 mm / 1.0 in. x 0.6 in. in size. 7c40 0300 out the battery and affix the 2 Take label. Y P O Set the power switch to <2>.
3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery Pack You can check the remaining capacity of any battery pack (even when not installed) and also when it was last used. Look for the serial number. Serial number Date last used Refer to the battery’s serial number label and look for the battery’s serial number on the battery history screen. X You can check the respective battery pack’s remaining capacity and the date when it was last used.
Using a Household Power Outlet With AC Adapter Kit ACK-E6 (sold separately), you can connect the camera to a household power outlet and not worry about the remaining battery level. 1 Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the AC Adapter’s socket. the power cord. 2 Connect Connect the power cord as shown in the illustration. After using the camera, unplug the power plug from the power outlet. Y P O the cord in the groove.
H Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card manufacturer.
H Using Eye-Fi Cards the connection 4 Display information. Select [Connection info.], then press <0>. the [Access point SSID:]. 5 Check Check that an access point is displayed for [Access point SSID:]. You can also check the Eye-Fi card’s MAC address and firmware version. Press the button to exit the menu. Y P O the picture. 6 Take X The picture is transferred and the icon switches from gray (not connected) to one of the icons below.
H Using Eye-Fi Cards Cautions for Using Eye-Fi Cards If [53: Wi-Fi] is set to [Enable], image transfer with an Eye-Fi card is not possible. If “ ” is displayed, an error occurred while retrieving the card information. Turn the camera’s power switch off and on again. Even if [Eye-Fi trans.] is set to [Disable], it may still transmit a signal. In hospitals, airports, and other places where wireless transmissions are prohibited, remove the Eye-Fi card from the camera.
Function Availability Table According to Shooting Mode Still Photo Shooting o: Set automatically k: User selectable : Not selectable/Disabled Basic Zone Function A 7 C Creative Zone 8 2 3 4 5 6 F G d sf a F All image quality settings k k k k k k k k k*1 k*1 k k k k k selectable Automatically set/Auto ISO o o o o o o o o Manual o Picture Automatically set/Auto o o o o o o o o Style Manual selection o ISO speed Ambience-based shots Light/scene-based shots Creative filters*2 Auto k k k k k k k o
Function Availability Table According to Shooting Mode Basic Zone Function A 7 C 8 Creative Zone 2 3 4 5 6 F G d sf a F o*3 o*3 *4 o*3 *4 o o*3 o k AF AF Microadjustment k Continuous AF*2 k k k k k k k k k k k Metering Evaluative metering o o o o o o o o o o k mode Metering mode selection k Program shift k AE lock k Exposure Exposure compensation k AEB k Depth-of-field preview k Single shooting k k k k k k k k k k k AF-assist beam Drive High-speed continuous shooting Low-speed continuous shooting Si
Function Availability Table According to Shooting Mode Movie Shooting o: Set automatically k: User selectable : Not selectable/Disabled Movie Function Still Photos A 7 C 8 d s f F y k a All image quality settings selectable (movie) All image quality settings selectable (still photos) k k k k k k k k k Digital zoom k k k k k k k k k Video snapshots k k k k k k k k k ISO speed Picture Style k k k Automatically set/Auto ISO o o o o o o o o k o o k k Manual Automatically set/Auto o White bala
Function Availability Table According to Shooting Mode Movie Function y AF Still Photos A 7 C 8 d s f F k a z*1 M y k M u+Tracking k k k k k k k k k k k k FlexiZone - Multi k k k k k k k k k k k k FlexiZone - Single k k k k k k k k k k k k Manual focusing (MF) k k k k k k k k k k k k Movie Servo AF k k k k k k k k k k k k Metering mode o o o o o o o o o o o o Program shift k k k k AE lock Exposure Exposure compensation k k k k AEB Depth-of-field preview Single shooting High-speed co
Menu Settings Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Page 1* / 41* / 61* Image quality 73/83/74/84/7a/8a/b/c 116 VF grid display Disable / Enable Viewfinder level Hide / Show Beep Enable / Touch to Release shutter without card Enable / Disable 32 Image review Off / 2 sec. / 4 sec. / 8 sec. / Hold 60 64 66 / Disable 59 * Not selectable in or mode. * For movie shooting, [VF grid display] and [Viewfinder level] do not appear.
Menu Settings z: Shooting 3 (Red) Page Exposure compensation/AEB 1/3-stop increments, ±5 stops (AEB ±3 stops) 167 168 ISO speed settings ISO speed / ISO speed range / Auto ISO range / Minimum shutter speed 120 Auto Lighting Optimizer Disable / Low / Standard / High 140 OFF with M or Bulb White balance Q/W/E/R/Y/U/D/O/ P (Approx.
Menu Settings A1: Live View shooting 1 (Red) Page Live View shooting Enable / Disable 228 AF method u+Tracking / FlexiZone - Multi / FlexiZone - Single / Quick mode 233 Continuous AF Enable / Disable 228 Touch Shutter Enable / Disable 229 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 229 Aspect ratio 3:2 / 4:3 / 16:9 / 1:1 229 Exposure simulation Enable / During e / Disable 230 A2: Live View shooting 2 (Red) Silent LV shooting Mode 1 / Mode 2 / Disable 231 Metering timer 4 sec.
Menu Settings 3: Playback 2 (Blue) Page Resize Downsize the image’s pixel count 333 Rating [OFF] / l / m / n / o / p 302 Slide show Playback description / Display time / Repeat / Transition effect / Background music 312 Image jump w/6 1 image / 10 images / 100 images / Date / Folder / Movies / Stills / Rating 297 Highlight alert Disable / Enable 294 AF point display Disable / Enable 294 Playback grid Off / 3x3 l / 6x4 m / 3x3+diag n 291 Histogram display Brightness / RGB 295 Movie
Menu Settings 5: Set-up 1 (Yellow) Page Select folder Create and select a folder 149 File number Continuous / Auto reset / Manual reset 151 Auto rotate OnzD / OnD / Off 325 Format card Initialize and erase data on the card 57 Eye-Fi settings Displayed when a commercially-available EyeFi card is inserted 401 Auto power off 1 min. / 2 min. / 4 min. / 8 min. / 15 min. / 30 min.
Menu Settings 5: Set-up 3 (Yellow) Page Video system NTSC / PAL 265 319 Feature guide Enable / Disable 69 Touch control Standard / Sensitive / Disable 56 z Button display options Displays camera settings / Electronic level / Displays shooting functions 394 Wi-Fi Disable / Enable Wi-Fi function Transfer images between cameras / Connect to smartphone / Remote control (EOS Utility) / Print from Wi-Fi printer / Upload to Web service / View images on DLNA devices -* Y P O * The EOS 70D (N) d
Menu Settings 5: Set-up 4 (Yellow) Page Auto cleaning: Enable / Disable 340 Sensor cleaning Clean now Clean manually Battery info.
Menu Settings Movie Shooting Z1: Movie 1 (Red) Page AF method u+Tracking / FlexiZone - Multi / FlexiZone - Single 273 Movie Servo AF Enable / Disable 273 Silent LV shooting Mode 1 / Mode 2 / Disable 275 Metering timer 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 30 min. 275 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 276 Movie recording size 1920x1080 (6 / 5 / 4) (W / X) 1280x720 (8 / 7) (W / X) 640x480 (6 / 5) (X) 265 Digital zoom Disable / Approx.
System Map ST-E2 ST-E3-RT 270EX II 90EX 320EX 430EX II 600EX-RT/ Macro Ring Lite Macro Twin Lite MR-14EX MT-24EX 600EX Bundled Accessories Eyecup Eb Eyepiece Extender EP-EX15 Rubber Frame Eb Wide Strap EW-EOS70D C E-series Dioptric Adjustment Lenses Angle Finder C Y P O Battery Pack LP-E6 Battery Charger LC-E6 or LC-E6E AC Adapter DC Coupler AC-E6 DR-E6 AC Adapter Kit ACK-E6 Battery Grip BG-E14 Car Battery Cable CB-570 Car Battery Charger CBC-E6 Battery Magazine Battery Magazine BGM-E14L fo
System Map GPS Receiver GP-E2 Remote Controller RC-6 Remote Switch RS-60E3 EF lenses EF-S lenses External microphone Y P O HDMI Cable HTC-100 (2.9 m/9.5 ft.) Stereo AV Cable AVC-DC400ST (1.3 m/4.3 ft.) C EOS DIGITAL Solution Disk TV/Video PictBridge-compatible printer Interface Cable (1.3 m/4.3 ft.) Interface Cable IFC-200U/IFC-500U (1.9 m/6.2 ft./4.7 m/15.4 ft.
Troubleshooting Guide If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power-Related Problems The battery pack does not recharge. If the battery’s remaining capacity is 94% or higher, the battery will not be recharged (p.396). Do not recharge any battery pack other than genuine Canon Battery Pack LP-E6. The charger’s lamp blinks at high speed.
Troubleshooting Guide The access lamp still blinks even when the power switch is set to <2>. If the power is turned off while an image is being recorded to the card, the access lamp will remain on or continue to blink for a few seconds. When the image recording is completed, the power will turn off automatically. The battery becomes exhausted quickly. Use a fully-charged battery pack (p.28). The battery performance may have degraded. See [54: Battery info.
Troubleshooting Guide Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-M lenses (p.40). The viewfinder is dark. Install a recharged battery pack in the camera (p.28). No images can be shot or recorded. Make sure the card is properly inserted (p.31). Slide the card’s write-protect switch to the write/erase position (p.31). If the card is full, replace the card or delete unnecessary images to make space (p.31, 322).
Troubleshooting Guide The image is out of focus. Set the lens focus mode switch to (p.40). To prevent camera shake, press the shutter button gently (p.44, 45). If the lens has an Image Stabilizer, set the IS switch to <1>. In low light, the shutter speed may become slow. Use a faster shutter speed (p.160), set a higher ISO speed (p.120), use flash (p.188, 193), or use a tripod. I cannot lock the focus and recompose the shot. Set the AF operation to One-Shot AF.
Troubleshooting Guide ISO 100 cannot be set. ISO speed expansion cannot be selected. When [z4: Highlight tone priority] is set to [Disable], ISO 100/125/ 160 can be set (p.145). If [z4: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200 - ISO 12800 (or up to ISO 6400 for movie shooting). Even if you expand the settable ISO speed range in [ISO speed range], you cannot set expanded ISO speeds (H). The Auto Lighting Optimizer cannot be set.
Troubleshooting Guide The built-in flash is raised by itself. In shooting modes (<2><4><6>) whose default setting is (Auto flash), the built-in flash will rise automatically when necessary. The built-in flash does not fire. If you shoot continuously with the built-in flash at short intervals, the flash may stop operating to protect the flash unit. The external flash does not fire. If you use a non-Canon flash unit with Live View shooting, set [A2: Silent LV shoot.] to [Disable] (p.231).
Troubleshooting Guide The shutter makes two shooting sounds during Live View shooting. If you use flash, the shutter will make two sounds each time you shoot (p.217). During Live View and movie shooting, a white < red icon is displayed. > or It indicates that the camera’s internal temperature is high. If the white < > icon is displayed, the still photo’s image quality may deteriorate. If the red icon is displayed, it indicates that the Live View or movie shooting will soon stop automatically (p.
Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie when [Maximum: H (25600)] is set with [ISO speed range] and ISO speed is set to “H” (25600), the ISO speed will switch to “H” (12800) (during movie shooting with manual exposure). Even if you switch back to still photo shooting, the ISO speed will not revert to the original setting. The exposure changes during movie shooting.
Troubleshooting Guide Wi-Fi Wi-Fi cannot be set.* If the camera is connected to a printer, computer, GPS receiver, or other device with an interface cable, Wi-Fi cannot be set ([53: Wi-Fi] will be grayed out). Disconnect the interface cable, then set the Wi-Fi. For details, refer to the Wi-Fi Function Instruction Manual. * The EOS 70D (N) does not have the Wi-Fi function. Operation Problems I cannot change the setting with the <6> dial, <5> dial, or <9>.
Troubleshooting Guide Display Problems The menu screen shows few tabs and options. In Basic Zone modes, certain tabs and menu options are not displayed. Set the shooting mode to a Creative Zone mode (p.52). The file name’s first character is an underscore (“_”). Set the color space to sRGB. If Adobe RGB is set, the first character will be an underscore (p.155). The file name starts with “MVI_”. It is a movie file (p.152). Y P O The file numbering does not start from 0001.
Troubleshooting Guide The LCD monitor does not display a clear image. If the LCD monitor is dirty, use a soft cloth to clean it. In low or high temperatures, the LCD monitor display may seem slow or may look black. It will return to normal at room temperature. [Eye-Fi settings] does not appear. [Eye-Fi settings] will appear only when an Eye-Fi card is inserted in the camera.
Troubleshooting Guide When the movie is played back, camera operation noise can be heard. If you operate the camera’s dials or lens during movie shooting, the operation noise will also be recorded. Using an external microphone (commercially available) is recommended (p.269). The movie has still moments. During autoexposure movie shooting, if there is a drastic change in the exposure level, the recording will stop momentarily until the brightness stabilizes.
Troubleshooting Guide I cannot process the RAW image. 41 and 61 images cannot be processed with the camera. Use the provided software Digital Photo Professional to process the image (p.456). I cannot resize the image. c JPEG images and 1/41/61 images cannot be resized with the camera (p.333). Sensor Cleaning Problems The shutter makes a noise during sensor cleaning. If you selected [Clean nowf], the shutter will make a noise, but no picture is taken (p.340).
Troubleshooting Guide Computer Connection Problems I cannot transfer images to a personal computer. Install the provided software (EOS DIGITAL Solution Disk CD-ROM) on the computer (p.456). If [53: Wi-Fi] is set to [Enable], the camera cannot be connected to a computer. Set [Wi-Fi] to [Disable], then connect the camera to the computer with an interface cable.
Error Codes If there is a problem with the camera, an error message will appear. Follow the onscreen instructions. Error number Cause and countermeasures Number Error Message and Solution Communications between the camera and lens is faulty. Clean the lens contacts. 01 Î Clean the electrical contacts on the camera and lens, use a Canon lens, or remove and install the battery pack again (p.19, 20, 30). Y P O Card cannot be accessed. Reinsert/change card or format card with camera.
Specifications • Type Type: Recording media: Image sensor size: Compatible lenses: Lens mount: Digital, single-lens reflex, AF/AE camera with built-in flash SD memory card, SDHC memory card*, SDXC memory card* * UHS-I cards compatible. Approx. 22.5 x 15.0mm Canon EF lenses (including EF-S lenses) * Excluding EF-M lenses (35mm-equivalent focal length is approx. 1.6 times the lens focal length) Canon EF mount • Image Sensor Type: Effective pixels: Aspect ratio: Dust delete feature: CMOS sensor Approx.
Specifications White balance: Noise reduction: Automatic image brightness correction: Highlight tone priority: Lens aberration correction: Auto, Preset (Daylight, Shade, Cloudy, Tungsten light, White fluorescent light, Flash), Custom, Color temperature setting (approx.
Specifications • Exposure Control Metering modes: Metering brightness range: Exposure control: ISO speed: (Recommended exposure index) ISO speed settings: Exposure compensation: AE lock: 63-zone TTL full-aperture metering • Evaluative metering (linked to all AF points) • Partial metering (approx. 7.7% of viewfinder at center) • Spot metering (approx. 3.
Specifications Shutter speeds: 1/8000 sec. to 30 sec. (total shutter speed range; available range varies by shooting mode), Bulb, X-sync at 1/250 sec. • Drive System Drive modes: Continuous shooting speed: Max. burst: Single shooting, High-speed continuous shooting, Lowspeed continuous shooting, Silent single shooting, Silent continuous shooting, 10-sec. self-timer/remote control, 2-sec. self-timer/remote control High-speed continuous shooting: Max. approx. 7.0 shots/sec.
Specifications Continuous AF: Focusing brightness range: Metering modes: Metering brightness range: Creative filters: Silent shooting: Touch shutter: Grid display: Provided EV 0-18 (at room temperature, ISO 100) Evaluative metering (315 zones), Partial metering (approx. 10.3% of Live View screen), Spot metering (approx. 2.
Specifications Exposure control: Exposure compensation: ISO speed: (Recommended exposure index) Time code: Drop frames: Video snapshots: Sound recording: Grid display: Still photo shooting: • LCD Monitor Type: Monitor size and dots: Brightness adjustment: Electronic level: Interface languages: Touch screen technology: Feature guide / Help: Autoexposure shooting (Program AE for movies) and manual exposure ±3 stops in 1/3-stop increments (±5 stops for still photos) For autoexposure shooting: 1.
Specifications Rating: Movie playback: Slide show: Background music: Image protect: Provided Enabled (LCD monitor, video/audio OUT, HDMI OUT), built-in speaker All images, by date, by folder, by movies, by stills, by rating Selectable for slide shows and movie playback Possible • Post-Processing of Images In-camera RAW image processing: Resize: Creative filters: Brightness correction, White balance, Picture Style, Auto Lighting Optimizer, High ISO speed noise reduction, JPEG image-recording quality, Co
Specifications • Power Battery: Battery Pack LP-E6 (Quantity 1) * AC power can be supplied via AC Adapter Kit ACK-E6. * With Battery Grip BG-E14 attached, size-AA/LR6 batteries can be used. Battery information: Remaining capacity, Shutter count, Recharge performance, and Battery registration possible Number of possible With viewfinder shooting: shots: Approx. 920 shots at room temperature (23°C/73°F), (Based on CIPA testing approx.
Specifications Working temperature 5°C - 40°C / 41°F - 104°F range: Working humidity: 85% or less Dimensions (W x H x D): Approx. 69.0 x 33.0 x 93.0 mm / 1.5 x 0.8 x 3.7 in. Weight: Approx. 130g / 23.6 oz. • Battery Charger LC-E6E Compatible battery: Power cord length: Recharging time: Rated input: Rated output: Working temperature range: Working humidity: Dimensions (W x H x D): Weight: Battery Pack LP-E6 Approx. 1 m / 3.3 ft. Approx. 2 hr. 30 min. 100 - 240 V AC (50/60 Hz) 8.4 V DC / 1.
Specifications Closest focusing distance*: At 18 mm focal length: 0.39 m / 1.28 ft. (Approx. 372 x 248 mm / 14.6 x 9.8 in. field of view) At 135 mm focal length: 0.39 m / 1.28 ft. (Approx. 80 x 53 mm / 3.1 x 2.1 in. field of view) * Distance from image sensor plane Max. magnification: 0.28x (at 135 mm) Image Stabilizer: Lens shift type Filter size: 67 mm Lens cap: E-67 II Max. diameter x length: Approx. 76.6 x 96.0 mm / 3.0 x 3.8 in. Weight: Approx. 480 g / 16.9 oz.
Handling Precautions: EF-S18-55mm f/3.5-5.6 IS STM, EF-S18-135mm f/3.5-5.6 IS STM The kit lenses use a stepping motor that drives the focus lens. The motor controls the focus lens even during zooming. 1. When the camera is OFF The motor does not operate while the camera is OFF or when the camera is OFF due to the auto power off function. Therefore, users must be aware of the following points. Manual focusing is not possible. During zooming, inaccurate focusing may occur. 2.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• Before storing the camera or accessory when not in use, remove the battery pack and disconnect the power plug. This is to prevent electrical shock, heat generation, and fire. • Do not use the equipment where there is flammable gas. This is to prevent an explosion or fire. • If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment.
Preventing Injury or Equipment Damage • Do not leave equipment inside a car under the hot sun or near a heat source. The equipment may become hot and cause skin burns. • Do not carry the camera around while it is attached to a tripod. Doing so may cause injury. Also make sure the tripod is sturdy enough to support the camera and lens. • Do not leave a lens or lens-attached camera under the sun without the lens cap attached. Otherwise, the lens may concentrate the sun’s rays and cause a fire.
Digital Camera Model DS126411 / DS126412 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS — This manual contains important safety and operating instructions for Battery Charger LC-E6 & LC-E6E. 2. Before using the charger, read all instructions and cautionary remarks on (1) the charger, (2) the battery pack, and (3) the product using the battery pack. 3. CAUTION — To reduce risk of injury, charge only the Battery Pack LP-E6. Other types of batteries may burst, causing personal injury and other damage. 4.
MEMO C 450 Y P O
Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer Y P O This chapter explains how to install the Camera Instruction Manual CD-ROM to your computer, download images from the camera to your computer, gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on your computer. It also explains how to view the PDF files on the Software Instruction Manual CDROM.
Viewing the Camera Instruction Manual CD-ROM The Camera Instruction Manual CD-ROM contains the following electronic manuals (PDF): Camera Instruction Manual Explains all the camera functions and procedures, including basic content. Wi-Fi Function Instruction Manual Explains all the Wi-Fi functions and procedures, including basic content. Quick Reference Guide Simple and portable guide covering basic function settings, shooting instructions, and playback instructions.
Viewing the Camera Instruction Manual CD-ROM the START file. 3 Double-click X The screen shown in step 4 will appear. The icon displayed will differ depending on your computer’s operating system. 4 Select the language. EOS 70D (W) / EOS 70D (N) 日本語 English Français Español © CANON INC. 2013 Y P O 5 Click on the manual you want to view.
Downloading Images to a Computer You can use the provided software to download the images in the camera to your computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer 1 Install the software (p.458). the provided interface cable 2 Use to connect the camera to your computer. Y P O Use the interface cable provided with the camera. Connect the cable to the camera’s terminal with the cable plug’s icon facing the front of the camera.
Downloading Images to a Computer Downloading Images with a Card Reader You can use a card reader to download images/movies to a computer. Install the software (p.458). 1 the card into the card 2 Insert reader. Y P O Canon software to download 3 Use the images. C X Use Digital Photo Professional. X Use ImageBrowser EX. For details, refer to the Software Instruction Manual on the CD-ROM (p.459).
Software Overview EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely with the computer connected to the camera. Also, you can copy background music tracks, such as EOS Sample Music*, to the card.
Software Overview Picture Style Editor You can edit Picture Styles and create and save original Picture Style files. This software is aimed at advanced users who are experienced in processing images.
Installing the Software Do not connect the camera to your computer before you install the software. The software will not be installed correctly. Even if your computer already has ImageBrowser EX installed, install ImageBrowser EX included on the CD-ROM that came with this camera. It is the latest version with features optimized for your camera. You can also use the auto update feature to add the latest functions.
Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Software Instruction Manual PDFs 1 Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. 2 Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. 3 Copy the [English] folder to your computer. Y P O Instruction Manual PDFs with the names below are copied.
Index Numerics ALL-I (I-only) ................................ 265 10- or 2-sec. self-timer..................113 Ambience-based shots................... 92 1280x720 ......................................265 Aperture-priority AE...................... 162 1920x1080 ....................................265 Art bold effect ....................... 226, 337 19-point AF auto selection ............103 Aspect ratio .................................. 229 4- or 9-image index display...........296 Attenuator.
Index Holding the camera ....................44 Settings display ........................394 Cards ..............................3, 19, 31, 57 Card reminder.............................32 Formatting ..................................57 Low-level formatting ...................58 Problems ..............................33, 58 Write-protect switch ....................31 Center-weighted average metering ........................................166 DC Coupler...................................
Index File size.........................117, 266, 292 G Filter effects ..........................131, 335 GPS.............................................. 412 Final image simulation ..........221, 260 Grainy B/W........................... 226, 336 Fine (image-recording quality) ......117, 118 Grid display .................. 229, 276, 291 Firmware version ..........................414 First-curtain synchronization.........200 Fish-eye effect ......................
Index Histogram display .....................295 Index.........................................296 Jump display (image browsing) ......................297 Magnification ............................298 Manual rotation.........................301 Numbering ................................151 Playback ...................................289 Protecting .................................320 Ratings .....................................302 Shooting information.................292 Slide show .......................
Index Maximum burst .....................117, 119 Medium (image-recording quality) ......117, 333 Memory cards 9 Cards Menu...............................................52 My Menu...................................389 Setting procedure .......................53 Settings ....................................408 3 icon .........................................8 Metering mode..............................165 Metering timer...............................232 Microadjustment ...........................
Index Picture Style ..................126, 129, 132 Recharging ..................................... 28 Pixels ............................................116 Recording level............................. 268 Playback .......................................289 Red-eye reduction ........................ 190 Portrait ............................................82 Reduced display........................... 296 Possible shots.........................36, 217 Release shutter without card..........
Index 4 (Close-up)...........................84 5 (Sports)..............................85 6 (Night Portrait) ....................86 F (Handheld Night Scene) .....87 G (HDR Backlight Control).....88 Shooting orientation registration ...373 Shutter button .................................45 Shutter synchronization ................200 Shutter-priority AE ........................160 Silent shooting ........................80, 111 Continuous shooting...........80, 111 Silent LV shooting.....................
MEMO C Y P O 467
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. http://www.usa.canon.com/eos http://www.usa.canon.com/support For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.