Operation Manual

Custom Picture Settings
142
[Other Settings] > [Selective NR]
The camera detects the characteristics of a certain color or tone and applies a noise reduction filter to the
targeted areas. A zebra pattern will appear over targeted areas on the LCD screen or a monitor connected to the
MON. terminal.
[Effect Level]: Adjusts the level of the noise reduction filter. The available options are [Off], [Low], [Middle] and
[High]. (Default: [Off])
[Hue]: Adjusts the hue for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 0)
[Chroma]: Adjusts the color saturation for the color to be detected. This setting can be adjusted from 0 to
31. (Default: 16)
[Area]: Adjusts the color range for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Y Level]: Adjusts the brightness for the color to be detected. This setting can be adjusted from 0 to 31.
(Default: 16)
[Other Settings] > [Color Matrix Tuning]
Adjust in detail various aspects of the color matrix to affect the color tones of the whole image.
[Gain]: Adjusts the color intensity. This setting can be adjusted from –50 to 50. (Default: ±0)
[Phase]: Adjusts the color phase. This setting can be adjusted from –18 to 18. (Default: ±0)
[R-G]: The R-G matrix changes the tint of the picture along the cyan/green and red/magenta
gradations. This setting can be adjusted from –50 to 50. (Default: ±0)
[R-B]: The R-B matrix changes the tint of the picture along the cyan/blue and red/yellow gradations.
This setting can be adjusted from –50 to 50. (Default: ±0)
[G-R]: The G-R matrix changes the tint of the picture along the magenta/red and green/cyan
gradations. This setting can be adjusted from –50 to 50. (Default: ±0)
[G-B]: The G-B matrix changes the tint of the picture along the magenta/blue and green/yellow
gradations. This setting can be adjusted from –50 to 50. (Default: ±0)
[B-R]: The B-R matrix changes the tint of the picture along the yellow/red and blue/cyan gradations.
This setting can be adjusted from –50 to 50. (Default: ±0)
[B-G]: The B-G matrix changes the tint of the picture along the yellow/green and blue/magenta
gradations. This setting can be adjusted from –50 to 50. (Default: ±0)
[Other Settings] > [White Balance]
Adjusts the amount of white balance throughout the whole image.
[R Gain]: Adjust the intensity of red tones. This setting can be adjusted from –50 to 50. (Default: ±0)
[B Gain]: Adjust the intensity of blue tones. This setting can be adjusted from –50 to 50. (Default: ±0)
[Other Settings] > [Color Correction]
The camera detects the characteristics of a certain color (color phase, chroma, area and Y level) and corrects
them when recording. You can set the color correction for up to two different areas (A and B). While adjusting
one of the [Area A Setting] or [Area B Setting] settings, a zebra pattern will appear on the LCD screen or a
monitor connected to the MON. terminal over areas of the image detected as having the characteristics
specified for area A or area B.
[Select Area]: Selects the area or areas to correct. Available options are [Area A], [Area B] and [Area A&B].
Select [Off] to turn this setting off. (Default: [Off])
[Area A Setting Phase], [Area B Setting Phase]: Adjusts the color phase for area A or B, respectively. This setting
can be adjusted from 0 to 31. (Default: 0)
[Area A Setting Chroma], [Area B Setting Chroma]: Adjusts the color saturation for area A or B, respectively. This
setting can be adjusted from 0 to 31. (Default: 16)
[Area A Setting Area], [Area B Setting Area]: Adjusts the color range for area A or B, respectively. This setting can
be adjusted from 0 to 31. (Default: 16)