DIE-0415-000B Wireless File Transmitter WFT-E6 Y P O Guide for Canon Camcorders C E
Introduction About this Guide You can attach a WFT-E6 Wireless File Transmitter to a Canon camcorder to connect the camcorder to a Wi-Fi network. This will allow you to operate the camcorder remotely from any device connected to the Wi-Fi network using Wi-Fi Remote, a Web browser application. This guide will explain how to attach the WFT-E6 to a camcorder and configure the transmitter for use with a camcorder.
Contents Introduction 2 About this Guide ................................................................................................................................ 2 Attaching to a Camcorder .................................................................................................................. 4 1 Wi-Fi and Camcorder Settings 7 Connecting to a Wi-Fi Network ..........................................................................................................
Attaching to a Camcorder Turn off the camcorder before attaching the WFT-E6 Wireless File Transmitter. The transmitter is powered by the camcorder. Make sure the camcorder’s battery pack is sufficiently charged before using the transmitter. 1 2 Turn off the camcorder. Open the WFT terminal cover. Y 3 OP C Attach the transmitter. Align the transmitter’s terminal to the camcorder’s WFT terminal as shown in the illustration and firmly push it in ( ).
Attaching to a Camcorder 5 Turn on the camcorder. If the transmitter was correctly attached, the icon will appear in the rear panel, next to the remaining battery icon. Removal Turn off the camcorder. Loosen the WFT attachment bracket’s screw and remove the WFT attachment bracket. Loosen the transmitter’s tightening screw until it spins freely. Remove the transmitter from the camcorder’s WFT terminal and close the WFT terminal’s cover.
C Y P O
1 Wi-Fi and Camcorder Settings Y P O Complete the Wi-Fi and camcorder settings using the camcorder’s menu screens.
Connecting to a Wi-Fi Network Before using the Wi-Fi Remote application to remotely control the camcorder, you need to wirelessly connect the camcorder (with the transmitter attached) to a Wi-Fi network via an access point (wireless router). There are six ways to do so, and the method you use will depend on the ype and specifications of the access point or device you want to use. Note that using an unprotected Wi-Fi network can expose your data to monitoring by unauthorized third parties.
Connecting to a Wi-Fi Network AP Mode When shooting in a location where there are no access points available, the camcorder can serve as a wireless access point*. Wi-Fi enabled devices will be able to connect to the camcorder directly and operate it through the Wi-Fi Remote application. This mode can only be used with compatible camcorders. * Limited only to the connection between the camcorder and supported Wi-Fi enabled devices.
Wi-Fi Protected Setup (WPS) - Button Wi-Fi Protected Setup (WPS) is the easiest way to set up the Wi-Fi network. However, it may not work correctly if there are several active access points in the area. In such case try using the [WPS: Pin Code] (A 11) or [Connection Wizard] (A 12) option. 1 2 3 Open the [Set Up New] submenu. [w Other Functions] > [Wi-Fi Remote] > [Set Up New] Select [WPS: Button] and then press SET. Press and hold the WPS button on the wireless router.
Wi-Fi Protected Setup (WPS) - PIN Code In this setup mode, the camcorder will issue an 8-digit PIN code that you then need to enter in the wireless router setup screen. Even if there are multiple access points active in your area, this is a relatively reliable method of establishing a connection using a shared PIN code. It may take about one minute to establish connection. 1 2 3 Open the [Set Up New] submenu. [w Other Functions] > [Wi-Fi Remote] > [Set Up New] Select [WPS: PIN Code] and then press SET.
Searching for Access Points The transmitter will detect active Wi-Fi networks in your area and you can select the desired access point (SSID) from the list. Then, follow the instructions on the screen to complete the connection wizard. 1 2 3 4 Open the [Set Up New] submenu. [w Other Functions] > [Wi-Fi Remote] > [Set Up New] Select [Connection Wizard] and then press SET. Select [Automatic] and then press SET.
Searching for Access Points Encrypted Access Points If the access point is encrypted (C), you will need to enter the encryption key (password). To find out the encryption key, refer to the instruction manual of the access point (wireless router) or consult the network administrator. If the access point is not encrypted, continue directly with the procedure to configure the IP address assignment (A 17). 1 [WEP]/[Shared Key] Select the WEP index key.
Manual Setup/AP Mode/Ad Hoc Connection If you prefer, you can enter manually the details of the Wi-Fi network you want to connect to or you can connect directly to a Wi-Fi enabled device. Follow the instructions on the screen to complete the connection wizard. After step 2 in the Searching for Access Points procedure (A 12): 1 2 Select [Manual] and then press SET. Select the wireless connection mode and then press SET.
Manual Setup/AP Mode/Ad Hoc Connection AP Mode Connections 4 5 Select the channel and then press SET. Available channels will be different for 11b/g/n and 11a/n connections. Select the AP mode’s encryption method and then press SET. If you selected [Open/No encryption], skip to step 7. If you selected [WPA2-PSK/AES], continue with step 6. Ad Hoc Connections 4 5 Select the channel and then press SET. Available channels will be different for 11b/g and 11a connections.
Manual Setup/AP Mode/Ad Hoc Connection 6 7 Enter the encryption key as described in the previous section (A 13). Depending on the settings, you may need to select the WEP index key first. Continue with the procedure to configure the IP address assignment (A 17).
Configuring Network (TCP/IP) Settings 1 Select [Automatic] or [Manual] and then press SET. 2 Enter the network’s TCP/IP settings manually. If you selected [Automatic], IP settings will be assigned automatically. Continue with the procedure to review and save the configuration (A 18). C Enter the IP address assigned to the camcorder, and the network’s subnet mask, and default gateway.
Saving the Configuration 1 2 Review the access point’s configuration and then press SET. The first screen shows the access point’s SSID and the type of connection. Push the joystick up/ down or turn the SELECT dial to review additional settings before pressing SET. Save the current configuration. C Select the desired configuration number and then press SET. You can save up to 5 different network configuration profiles on the camcorder.
Camcorder Settings for Camcorders With Multi-User Support You can set a unique camcorder identification code and designate the port that the Wi-Fi Remote application should use when accessing the transmitter through the Wi-Fi network. The Wi-Fi connection will be disabled while you change these settings. [Port No.] [Camera ID] The port number (HTTP protocol) used by Wi-Fi Remote. This is usually set to port 80, but you can change it if necessary.
User Settings for Camcorders With Multi-User Support A user name and password are required before the Wi-Fi Remote application (Wi-Fi enabled device connected to the Wi-Fi network) can access the transmitter in order to operate the camcorder. Depending on the camcorder used*, you can set up to three different users and select whether you want to allow single-user operation (only User 1) or multi-user operation (Users 2 and 3). The Wi-Fi connection will be disabled while you change these settings.
User Settings for Camcorders With Multi-User Support [User Name], [Password] 1 Use the joystick or turn the SELECT dial to select a character and then press SET to add it. Repeat this step as necessary to enter the desired text. 2 After entering the desired text, select [OK] and then press SET.
Camcorder Settings for Camcorders Without Multi-User Support A user name and password are required before the Wi-Fi Remote application (Wi-Fi enabled device connected to the Wi-Fi network) can access the transmitter in order to operate the camcorder. Additionally, you can set a unique camcorder identification code and designate the port that Wi-Fi Remote should use. The Wi-Fi connection will be disabled while you change these settings.
Camcorder Settings for Camcorders Without Multi-User Support [Port No.] 1 Push the joystick up/down or turn the SELECT dial to select a value for the first field and then press SET to move to the next field. 2 After completing all the fields, select [Set] and press SET to enter the port number.
C Y P O
2 Remote Operation Using Wi-Fi Remote Y P O After completing the preparations in the previous chapter, you can use any computer or other Wi-Fi enabled device that has a Web browser and is connected to the same Wi-Fi network to remotely operate the camcorder using the Wi-Fi Remote application.
Selecting a Configuration Number You can save up to 5 different network configuration profiles. You can select which one to use depending on where you plan to use the camcorder. If you just saved a new network configuration (A 18), the camcorder will automatically connect to that Wi-Fi network and this procedure is not required. 1 2 Open the Wi-Fi [Select] submenu. [w Other Functions] > [Wi-Fi Remote] > [Select] Select the desired configuration number and then press SET.
Starting Wi-Fi Remote After establishing a connection between the camcorder and Wi-Fi network (the white icon appears on the upper left of the screen1), you can start the Wi-Fi Remote application on any Wi-Fi enabled device2 that has a Web browser3 and is connected to the same Wi-Fi network. Refer also to the instruction manual of the Wi-Fi enabled device used. 1 2 3 For AP mode/Ad Hoc connections, you need to actively connect the device (A 18) directly to the camcorder.
Starting Wi-Fi Remote Starting Wi-Fi Remote You can specify the port number 1 2 Start the Web browser on the computer or other Wi-Fi enabled device. Enter the camcorder’s URL. Enter the IP address you checked previously into the Web browser’s address bar, adding the prefix “http://”. If the you chose a port other than “80”, you can specify it by adding “:nnn” at the end of the URL. For example “http://192.168.0.80:095”. Camcorder’s IP address from the Status screen 3 Example of the login screen.
Starting Wi-Fi Remote Screen selection tabs appear only for [User 1]/single-user operation Language selection Wi-Fi connection indicator Camcorder ID 4 Y P O Select the language for Wi-Fi Remote. C Press the [Î] next to the language button and select the desired language from the list. Most buttons and controls emulate physical controls on the camcorder and are labeled in English only, regardless of the language selected.
Wi-Fi Remote: [Advanced Control] Single-user operation/[User 1]/[User 2] only When using a laptop computer, netbook, tablet computer or other Wi-Fi enabled devices with larger screens, the [Advanced Control] screen offers more shooting controls to operate the camcorder. For details about how to control the recording or change the various settings, refer to the relevant section in the camcorder’s instruction manual.
Wi-Fi Remote: [Basic Control] Single-user operation/[User 1] only When using a smartphone or other Wi-Fi enabled device with a smaller screen, you can use the [Basic Control] screen that offers only the most important shooting controls (focus, iris, START/STOP, live view, all types of marks and Wi-Fi Remote button lock) but will fit in the screen without scrolling.
Wi-Fi Remote: [Metadata Input] Single-user operation/[User 3] only Using Wi-Fi Remote you can create, edit and transfer to the camcorder a metadata profile that includes the User Memo information (clip title, creator, location and description), as well as GPS information. For details about how to set and transfer the metadata, refer to the relevant section in the camcorder’s instruction manual. 1 Open the [Metadata Input] screen. From the [Advanced Control] screen press the [Metadata Input] tab.
3 Managing Settings Information C Y P O 33
Checking Settings You can check the current Wi-Fi network settings using the camcorder’s status screens. 1 2 Press the STATUS button. Push the joystick up/down or turn the SELECT dial to display the four [Wi-Fi Remote] status screens.
Changing Settings You can edit the Wi-Fi network settings even after the initial setup. Changing settings manually requires more advanced knowledge of Wi-Fi and network settings. The Wi-Fi connection will be disabled while you change these settings. After completing the changes, the camcorder will connect to the Wi-Fi network using the new configuration. 1 2 3 Select the network configuration profile you want to change (A 26). Open the Wi-Fi [Edit] submenu.
Changing Settings 7 If you selected [Manual], select a setting you want to change and then press SET. Push the joystick up/down or turn the SELECT dial to select a value for the first field and press SET to move to the next field. After completing the four fields of each address, select [Set] and press SET to enter the address. Repeat this step to change other TCP/IP settings as necessary. When you finish changing the settings, select [L], press SET and then close the menu.
4 Troubleshooting C Y P O 37
Troubleshooting Check this section if you encounter problems connecting to the Wi-Fi network or operating the camcorder remotely from a Wi-Fi enabled device. If the problem persists, consult a Canon Service Center (listed on the back cover of the camcorder’s instruction manual).
About Wi-Fi Networks When using the transmitter with a Wi-Fi network, try the following corrective actions if the transmission rate drops, the connection is lost, or other problems occur. Location and Antenna Position of the Wireless Router or Wi-Fi Enabled Device When using the transmitter indoors, place the wireless router in the same room where you are shooting. Place the wireless router in an open, unobstructed location, where people or objects do not come between it and the camcorder.
Error Messages Refer to this list when an error message is displayed on the camcorder’s screen. Messages are listed alphabetically. If the problem persists, consult a Canon Service Center (listed on the back of the camcorder’s instruction manual). Another user is already accessing the camcorder. Try again later. The camcorder is already connected to the same user on another instance of Wi-Fi Remote on another Web browser. X A single user cannot log in to control the camcorder from multiple devices.
Error Messages Wi-Fi connection terminated An error occurred on the access point or the computer or other Wi-Fi enabled device. X Check the Wi-Fi enabled device and access point and try connecting again. The Wi-Fi signal became too weak and the wireless connection was lost. X Wait a moment or turn off other devices in the area that may be interfering with the Wi-Fi signal and then try connecting again. Wi-Fi error. Incorrect encryption key.
Index A N Access point .......................................... 2, 12 Ad Hoc................................................... 9, 14 Advanced Control screen .......................... 30 AP mode................................................ 9, 14 Area of use .... Areas of Use and Restrictions Attaching to a camcorder ............................ 4 Authentication............................................ 15 B Camcorder ID ...................................... 19, 22 Camcorder settings ...........
C Y P O Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance. WPS as used on the camcorder’s settings, onscreen displays and in this manual signifies Wi-Fi Protected Setup.
C Y P O The information in this guide is current as of August 2013. For information on using the transmitter with accessories introduced after this date, contact your nearest Canon Service Center. DIE-0415-000B © CANON INC.