EOS 6D (WG) EOS 6D (N) PY O C E The EOS 6D (N) does not have the Wi-Fi and GPS functions explained in this manual.
Introduction The EOS 6D (WG/N) is high-performance, digital single-lens reflex camera featuring a full-frame (approx. 35.8 x 23.9 mm) CMOS sensor with approx. 20.2 effective megapixels, DIGIC 5+, high-precision and high-speed 11-point AF, approx. 4.5 fps continuous shooting, Live View shooting, Full High-Definition (Full HD) movie shooting, Wi-Fi*, and GPS*.
Compatible Cards The camera can use the following cards regardless of capacity: • SD memory cards • SDHC memory cards* • SDXC memory cards* * UHS-I cards compatible. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table. Compression Method (p.216) Card IPB 6 MB/sec. or faster ALL-I (I-only) 20 MB/sec. or faster If you use a slow-writing card when shooting movies, the movie may not be recorded properly.
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Camera (with body cap) Wide Strap EW-EOS6D Battery Pack LP-E6 (with protective cover) Interface Cable IFC-200U PY O C Battery Charger LC-E6/LC-E6E* Stereo AV Cable AVC-DC400ST * Battery Charger LC-E6 or LC-E6E is provided. (The LC-E6E comes with a power cord.) The Instruction Manuals and CD-ROMs provided are listed on the next page.
Instruction Manuals and CD-ROMs The instruction manuals are provided in both paper and electronic (PDF) forms. Camera Basic Instruction Manual Pocket Guide Explains the camera’s basic function settings and basic shooting/playback instructions. Wi-Fi (Basic)/ GPS Function Instruction Manual* Wi-Fi/GPS Cautions* PY O C * Not provided with the EOS 6D (N).
Conventions Used in this Manual Icons in this Manual <6> <5> <9> <0> 0, 9, 7, 8 : Indicates the Main Dial. : Indicates the Quick Control Dial. : Indicates the Multi-controller and the push direction. : Indicates the Setting button. : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec. respectively after you let go of the button.
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures.
Contents Introduction 2 Compatible Cards............................................................................. 3 Item Check List................................................................................. 4 Instruction Manuals and CD-ROMs.................................................. 5 Conventions Used in this Manual ..................................................... 6 Chapters...........................................................................................
Contents 2 Basic Shooting 65 A Fully Automatic Shooting (Scene Intelligent Auto) ................... 66 A Full Auto Techniques (Scene Intelligent Auto).......................... 69 C Creative Auto Shooting............................................................. 71 8: Special Scene Mode ............................................................. 74 2 Shooting Portraits ...................................................................... 75 3 Shooting Landscapes ..................................
Contents Setting the White Balance ............................................................ 120 O Custom White Balance........................................................ 121 P Setting the Color Temperature ............................................ 122 White Balance Correction............................................................. 123 Auto Correction of Brightness and Contrast ................................. 125 Noise Reduction Settings ...................................................
Contents 6 Flash Photography 169 D Flash Photography .................................................................... 170 Setting the Flash ........................................................................... 172 7 Shooting with the LCD Monitor (Live View Shooting) 179 A Shooting with the LCD Monitor ............................................... 180 Shooting Function Settings ........................................................... 185 Menu Function Settings .........................
Contents X Editing a Movie’s First and Last Scenes ................................. 255 Slide Show (Auto Playback) ......................................................... 257 Viewing the Images on TV............................................................ 261 K Protecting Images................................................................... 265 L Erasing Images........................................................................ 267 Changing Image Playback Settings ...........................
Contents C.Fn I: Exposure ........................................................................ 304 C.Fn II: Autofocus ...................................................................... 307 C.Fn III: Operation/Others .......................................................... 311 8: AF Microadjustment ............................................................... 314 8: Custom Controls .................................................................... 320 Registering My Menu ......................
Index to Features Power AF Charging the battery Î p.28 AF operation Î p.92 Battery check Î p.35 AF point selection Î p.94 Battery information check Î p.334 AF Microadjustment Î p.314 Household power outlet Î p.338 Manual focusing Î p.97 Auto power off Î p.55 Metering Card Format Metering mode Drive Release shutter without card Î p.32 Lens Attaching/Detaching Î p.39 Zoom Î p.40 Image Stabilizer Î p.42 Basic Settings Drive mode Î p.98 Self-timer Î p.100 Maximum burst Î p.
Index to Features Shooting Playback Shooting mode Î p.24 HDR Î p.155 Multiple exposures Î p.158 Mirror lockup Î p.165 Depth-of-field preview Î p.147 Remote control Î p.167 Quick Control Î p.49 Exposure Adjustment Exposure compensation Î p.151 AEB Î p.152 AE lock Î p.153 Safety shift Î p.306 Flash Image review time Î p.55 Single-image display Î p.236 Shooting information display Î p.238 Index display Î p.242 Image browsing (Jump display) Î p.243 Magnified view Î p.
Handling Precautions Camera Care This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth. Never leave the camera near anything having a strong magnetic field such as a magnet or electric motor.
Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision technology with over 99.99% effective pixels, there may be a few dead pixels displaying only black or red, etc. among the remaining 0.01% or less pixels. Dead pixels are not a malfunction. They do not affect the images recorded. If the LCD monitor is left on for a prolonged period, screen burn-in may occur where you see remnants of what was displayed.
Quick Start Guide 1 2 Insert the battery (p.30). To charge the battery, see page 28. Insert a card (p.31). With the card’s label facing toward the back of the camera, insert it into the card slot. 3 Attach the lens (p.39). 4 Set the lens focus mode switch to (p.39). 5 18 Align it with the red dot. PY O C Set the power switch to <1> (p.34). When the LCD monitor displays the date/time/zone setting screens, see page 36.
Quick Start Guide 6 While holding down the center of the Mode Dial, set it to (Scene Intelligent Auto) (p.66). All the necessary camera settings will be set automatically. 7 8 9 Focus the subject (p.44). Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway, and the camera will focus the subject. PY Press the shutter button completely O C to take the picture. Take the picture (p.44). Review the picture (p.55).
Nomenclature LCD panel (p.22) Drive mode selection button (p.98) AF operation selection button (p.92) ISO speed setting button (p.106) Metering mode selection button (p.149) Lens mount index (p.39) Flash-sync contacts LCD panel illumination button (p.48) Hot shoe (p.170) <6> Main Dial (p.45) Mode Dial lock release button (p.45) Mode Dial (p.24) Shutter button (p.44) Strap mount (p.27) Self-timer lamp (p.100) PY O C Remote control sensor (p.167) Speaker (p.253) Microphone (p.
Nomenclature
AF start button (p.44, 181, 211) Focal plane mark Live View shooting/ Movie shooting switch (p.179/203) <0> Start/Stop button (p.180, 204) AE lock/ FE lock button (p.153/170) Dioptric adjustment knob (p.43) AF point selection button (p.94) Eyecup (p.166) Viewfinder eyepiece Quick Control button (p.49) Strap mount (p.27) Power switch (p.34) Menu button (p.51) Card slot cover (p.31) Info button (p.
Nomenclature LCD Panel Drive mode (p.98) u Single shooting i Continuous shooting B Silent single shooting M Silent continuous shooting Q Self-timer: 10 sec./ Remote control k Self-timer: 2 sec./ Remote control Highlight tone priority (p.130) ISO speed (p.106) ISO speed (p.106) Possible shots Self-timer countdown Bulb exposure time Error No. Remaining images to record AEB (p.152) AF operation (p.
Nomenclature Viewfinder Information AF points (p.94) (Superimposed display) Focusing screen (p.312) Spot metering circle (p.150) ISO speed (p.106) Warning symbol (p.313) Battery check (p.35) AE lock (p.153) / AEB in-progress (p.152) Flash-ready (p.170) Improper FE lock warning FE lock (p.170) / FEB in-progress (p.176) High-speed sync (p.175) Flash exposure compensation (p.170) Shutter speed (p.
Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). Creative Zone These modes give you more control for shooting various subjects. d : Program AE (p.142) s : Shutter-priority AE (p.144) f : Aperture-priority AE (p.146) a : Manual exposure (p.148) F : Bulb (p.154) Basic Zone Custom shooting mode You can register the shooting mode (d/s/f/a/F), AF operation, menu settings, etc., to the w or x Mode Dial setting and shoot (p.328).
Nomenclature Lens EF24-105mm f/4L IS USM Focus mode switch (p.39) Distance scale Infrared index Hood mount (p.41) Zoom ring (p.40) Zoom position index (p.40) φ77mm filter thread (front of lens) Focusing ring (p.97, 199) Contacts (p.17) Image Stabilizer switch (p.42) PY O C Lens mount index (p.
Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.28). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed. PY O C Battery Charger LC-E6E Charger for Battery Pack LP-E6 (p.28).
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Y P O Attaching the Strap C Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration. Pull the strap to take up any slack and make sure the strap will not loosen from the buckle. The eyepiece cover is also attached to the strap (p.166).
Charging the Battery 1 Remove the protective cover. Detach the protective cover provided with the battery. the battery. 2 Attach As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. LC-E6 the battery. 3 Recharge For LC-E6 As shown by the arrow, flip out the battery charger’s prongs and insert the prongs into a power outlet.
Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Recharge the battery before using. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet. You can attach the cover in a different orientation to indicate whether the battery has been recharged or not.
Installing and Removing the Battery Load a fully charged Battery Pack LP-E6 into the camera. Installing the Battery 1 Open the cover. Slide the lever as shown by the arrows and open the cover. the battery. 2 Insert Insert the end with the battery contacts. Insert the battery until it locks in place. the cover. 3 Close Ycover until it snaps shut. PressP the O C Only Battery Pack LP-E6 can be used. Removing the Battery Open the cover and remove the battery.
Installing and Removing the Card The camera can use an SD, SDHC, or SDXC memory card. UHS-I Speed Class SDHC and SDXC memory cards can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing/erasing. Installing the Card 1 Write-protect switch Open the cover. Slide the cover as shown by the arrows to open it. the card.
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent you from forgetting to insert a card (p.346). Removing the Card 1 Access lamp Open the cover. Set the power switch to <2>. Make sure the access lamp is off, then open the cover. If [Recording...] is displayed, close the cover. the card. 2 Remove Gently push Pit.
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to or read by the card, being erased, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking. Otherwise, it can damage the image data, card, or camera. • Removing the card. • Removing the battery. • Shaking or banging the camera around.
Turning on the Power If you turn on the power switch and the Date/Time/Zone setting screen appears, see page 36 to set the Date/Time/Zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera. About the Automatic Self-Cleaning Sensor Whenever you set the power switch to <1> or <2>, sensor cleaning will be executed automatically. (A small sound may be heard.) During the sensor cleaning, the LCD monitor will display .
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Icon Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 Number of Possible Shots 9-1 0 [Approx.
3 Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the Date/Time/Zone setting screens will appear. Follow the steps below to set the time zone first. If you set the camera to the correct time zone for where you currently live, when you travel to another time zone you can simply set the camera to the correct time zone for your destination to update the camera’s date/time automatically.
3 Setting the Date, Time, and Zone the date and time. 4 SetPress the key to select the number. Press <0> so is displayed. Press the key to set the number, then press <0>. (Returns to .) Saving Time. 5 SetSettheit ifDaylight necessary. Press the key to select [Y]. Press <0> so is displayed. Press the key to select [Z], then press <0>. When the daylight saving time is set to [Z], the time set in step 4 will advance by 1 hour.
3 Selecting the Interface Language 1 Display the menu screen. Press the button to display the menu screen. the [52] tab, select 2 Under [LanguageK]. Press the key to select the [52] tab. Press the key to select [LanguageK], then press <0>. PY O C the desired language. 3 SetPress the key to select the language, then press <0>. The interface language will change.
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S and EF-M lenses. 1 Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows. the lens. 2 Attach Align the red dots on the lens and camera and turn the lens as shown by the arrow until it clicks in place. the lens focus mode switch to 3 Set . PYstands for Autofocus. If it is set to (manual focus), O C autofocus will not operate.
Attaching and Detaching a Lens About Zooming To zoom, turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus slightly. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrows. Turn the lens until it stops, then detach it. Attach the rear lens cap to the detached lens.
Attaching and Detaching a Lens Attaching a Lens Hood A lens hood can block unwanted light and protect the front of the lens from rain, snow, dust, etc. Before storing the lens in a bag, etc., you can attach the hood in reverse. If the Lens Hood and Lens Have a Mount Index 1 Align the red dots on the hood and lens edges, and turn the hood as shown by the arrow. the hood as shown in the 2 Turn illustration. Turn the hood clockwise until it attaches securely.
About the Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF24-105mm f/4L IS USM lens as an example. * IS stands for Image Stabilizer. 1 Set the Image Stabilizer switch to <1>. Also set the camera’s power switch to <1>. the shutter button halfway. 2 Press The Image Stabilizer will operate. the picture.
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.166). If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (10 types, sold separately) is recommended. Holding the Camera To obtain sharp images, hold the camera still to minimize camera shake.
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0). Pressing completely This releases the shutter and takes the picture.
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. 6 Main Dial (1) After pressing a button, turn the <6> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <6> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot.
Basic Operation 5 Quick Control Dial (1) After pressing a button, turn the <5> dial. When you press a button such as , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5> dial to set the desired setting. When the function selection ends or if you press the shutter button halfway, the camera will be ready to shoot. Use this dial to select or set the AF operation, drive mode, ISO speed, metering mode, AF point selection, etc.
Basic Operation 9 Multi-controller The Multi-controller <9> has eight keys which tilt in the directions shown by the arrows. Use the eight keys to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, etc. For menus and the Quick Control, the Multi-controller works only in the vertical and horizontal directions . It does not work in diagonal directions. PY O With [8C.
Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed. With the shooting settings displayed, you can turn the Mode Dial to see the settings for each shooting mode (p.333).
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called the Quick Control screen. 1 Press the button. The Quick Control screen will appear (7). the desired function. 2 SetPress the key to select a function. The setting of the selected function is displayed. Turn the <6> or <5> dial to change the setting. Basic Zone modes Creative PY Zone modes O C the picture.
Q Quick Control for Shooting Functions Sample Quick Control Screen Aperture (p.146) Shutter speed (p.144) Shooting mode*1 (p.24) Flash exposure compensation (p.170) AE lock*1 (p.153) Highlight tone priority*1 (p.130) Exposure compensation/AEB setting (p.151, 152) ISO speed (p.106) Wi-Fi function*2 Picture Style (p.112) Custom Controls (p.320) AF operation (p.92) White balance (p.120) AF point (p.94) White balance correction (p.123) Drive mode (p.98) Image-recording quality (p.
3 Menu Operations You can set various settings with the menus such as the imagerecording quality, date/time, etc. While looking at the LCD monitor, use the button, keys, and <0> button on the camera back. button <0> button LCD monitor Menus in Basic Zone Modes PY O C * Some menu tabs and menu items are not displayed in Basic Zone modes.
3 Menu Operations Menu Setting Procedure 1 Display the menu screen. Press the button to display the menu screen. a tab. 2 Select Press the key to select a menu tab. For example, the [z4] tab refers to the screen displayed when the forth tab from the left [ ] is selected. the desired item. 3 Select Press the key to select the item, then press <0>. 4 PY O C Select the setting. Press the or key to select the desired setting.
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data in the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep. If necessary, transfer the images and data to a computer, etc., before formatting the card. 1 Select [Format card]. Under the [51] tab, select [Format card], then press <0>. PYthe card.
Before You Start Execute [Format card] in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed (p.370). About Low-level Formatting Perform low-level formatting if the card’s recording or reading speed seems slow or if you want to totally erase data in the card.
Before You Start 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. If you do not want the camera to turn off automatically, set this to [Disable]. After the power turns off, you can turn on the camera again by pressing the shutter button or other buttons. 1 Select [Auto power off]. Under the [52] tab, select [Auto power off], then press <0>. the desired time. 2 SetSelect the desired setting, then press <0>.
Before You Start 3 Turning the LCD Monitor Off/On The shooting settings display (p.48) can be set to remain on even when you press the shutter button halfway. Under the [52] tab, select [LCD off/on btn], then press <0>. The available settings are described below. Select one, then press <0>. [Remains on] : Display remains on even when you press the shutter button halfway. To turn off display, press the button. [Shutter btn.] : When you press the shutter button halfway, the display will turn off.
Before You Start Shooting Settings AF operation One-Shot AF AF point selection Automatic selection Metering mode q (Evaluative metering) ISO speed Auto ISO speed range Minimum limit: 100 Maximum limit: 25600 Multiple exposure Disable HDR Mode Disable HDR Auto ISO range Minimum limit: 100 Maximum limit: 12800 Mirror lockup Disable Custom Functions Unchanged Flash function settings Unchanged ISO Auto minimum Auto shutter speed Drive mode u (Single shooting) Exposure Canceled compensati
Before You Start Image-recording Settings Camera Settings Image quality Picture Style Auto Lighting Optimizer 73 Auto Auto power off Beep Release shutter without card 1 min. Enable Peripheral illumination correction Enable/ Correction data retained Image review Highlight alert AF point display Playback grid Histogram display Magnification (Approx.) 2 sec.
Before You Start Live View Shooting Settings Movie Shooting Settings AF method FlexiZone - Single FlexiZone - Single Silent LV shooting Mode 1 Grid display Off Metering timer 16 sec. Aspect ratio 3:2 Grid display Off Exposure simulation Enable Movie recording 1920x1080/IPB size Silent LV shooting Mode 1 Metering timer 16 sec.
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor, and in the viewfinder or on the LCD panel to help correct camera tilt. Note that you can check only the horizontal tilt and not the forward/backward tilt. Displaying the Electronic Level on the LCD Monitor 1 Press the button. Each time you press the button, the screen display will change. Display the electronic level.
Q Displaying the Electronic Level Displaying the Electronic Level in the Viewfinder The electronic level display in the viewfinder and on the LCD panel uses the exposure level indicator. Note that the electronic level is only displayed when shooting in horizontal orientation. It is not displayed in vertical orientation. 1 Select Custom Functions III. Under the [8] tab, select [C.Fn III: Operation/Others], then press <0>. C.Fn III -5 [Custom 2 Select Controls].
Q Displaying the Electronic Level the electronic level. 5 Display Press the Depth-of-field preview 4° right tilt 4° left tilt button. The horizontal tilt up to ±9° in 1° increments will be displayed in the viewfinder and on the LCD panel using the exposure level indicator. Pressing the shutter button halfway displays the exposure level. PY O C Even when the tilt is corrected, there may be a margin of error of ±1°. If the camera is very tilted, the electronic level’s margin of error will be bigger.
Feature Guide and Help While you set some function, the feature’s description can be displayed. Feature Guide The Feature guide displays a simple description of the respective shooting mode, function or option. It appears when you change the shooting mode or set a shooting function, Live View shooting, Movie shooting, or Quick Control for playback. When you select a function or option on the Quick Control screen, the Feature guide description appears.
Feature Guide and Help Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge. You can turn the <5> dial to scroll down. Example: [z4: Long exp. noise reduction] B Î Scroll bar PY O C Example: [8C.Fn I -1: Exposure level increments] B Î Example: [8C.
Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. PY O C ic Z on e With Basic Zone modes, all you do is point and shoot while the camera sets everything automatically (p.83, 342). Also, to prevent botched pictures due to mistaken operations, the main shooting function settings cannot be changed.
A Fully Automatic Shooting (Scene Intelligent Auto) is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.69). 1 AF point Set the Mode Dial to . Turn the Mode Dial while holding down the lock release button at the center. any AF point over the 2 Aim subject. All the AF points will be used to focus, and generally the closest object will be focused.
A Fully Automatic Shooting (Scene Intelligent Auto) the picture. 4 TakePress the shutter button completely to take the picture. The captured image will be displayed for 2 sec. on the LCD monitor. The mode makes the colors look more impressive in nature, outdoor, and sunset scenes. If the desired color tone is not obtained, use a Creative Zone mode and select a Picture Style other than and shoot (p.112). FAQ The focus confirmation light blinks and focus is not achieved.
A Fully Automatic Shooting (Scene Intelligent Auto) The shutter speed display is blinking. Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (p.170) (sold separately) is recommended. When the external flash was used, the bottom part of the picture came out unnaturally dark. If a hood is attached to the lens, it can obstruct the flash coverage.
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the mode, while you press the shutter button halfway to focus a still subject, the focus will be locked. You can then recompose the shot and press the shutter button completely to take the picture. This is called “focus lock”. Focus lock is also possible in other Basic Zone modes (except <5> Sports).
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 179. 1 Set the Live View shooting/Movie shooting switch to . the Live View image on 2 Display the LCD monitor. Press the <0> button. The Live View image will appear on the LCD monitor. the subject. Ycenter 3 Focus P Aim the AF point < O Csubject. > on the Press the shutter button halfway to focus.
C Creative Auto Shooting In the mode, you can easily change the depth of field and drive mode. You can also choose the ambience you want to convey in your images. The default settings are the same as the mode. * CA stands for Creative Auto. 1 Set the Mode Dial to . the button. (7) 2 Press The Quick Control screen will appear. the desired function. 3 SetPress the key to select a function. Y Pselected function and Feature The O C guide (p.63) will appear.
C Creative Auto Shooting (1) Shutter speed Aperture ISO speed (2) (3) Battery check Image-recording quality Possible shots Pressing the button enables you to set the following: PY O C (1) Ambience-based shots You can choose the ambience you want to convey in your images. Turn the <6> or <5> dial to select the desired ambience. You can also select it from a list by pressing <0>. For details, see page 84.
C Creative Auto Shooting (3) Drive mode: Press the key to select the desired drive mode. You can also select the drive mode by turning the <6> or <5> dial, or pressing <0> to select it from a list. Single shooting: Shoot one image at a time. Continuous shooting: While you hold down the shutter button completely, shots will be taken continuously. You can shoot up to approx. 4.5 shots per second. Silent single shooting: Single shooting with less shooting sound than .
8: Special Scene Mode When you set a shooting mode suiting the scene, the camera sets the optimum settings automatically. 1 Set the Mode Dial to <8>. the button. (7) 2 Press The Quick Control screen will appear. the shooting mode. 3 Select Press the key to select the shooting mode section. Turn the <6> or <5> dial to select a shooting mode. PY O C You can also select a shooting mode from a list by selecting the shooting mode section and pressing <0>.
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and the hair look softer. PY O The further the distance C between the subject and background, Shooting Tips the better. The further the distance between the subject and background, the more blurred the background will look. The subject will also stand out better in front of a plain, dark background. Use a telephoto lens.
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips PY O C With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end. It also adds breadth to landscapes. Shooting night scenes. When shooting night scenes, use a tripod to prevent camera shake.
4 Shooting Close-ups When you want to photograph flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips PY O C Use a simple background. A simple background makes the flower, etc., stand out better. Move as close as possible to the subject. Check the lens for its minimum focusing distance. Some lenses have indications such as <40.25m/0.8ft>.
5 Shooting Moving Subjects To photograph a moving subject, whether it is a child running or a moving vehicle, use the <5> (Sports) mode. Shooting Tips PY O C Use a telephoto lens. Using a telephoto lens is recommended so you can shoot from afar. Use the center AF point to focus. Aim the center AF point over the subject, then press the shutter button halfway to autofocus. During autofocusing, the beeper will continue beeping softly. If focus cannot be achieved, the focus confirmation light will blink.
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Flash is required. Using a tripod is also recommended. PY O C and a tripod. Use a wide-angle lens, Speedlite, Shooting Tips When using a zoom lens, use the wide-angle end to obtain a wide night view. Also, use a tripod to prevent camera shake. Also shoot in another shooting modes.
F Shooting Night Scenes (Handheld) Normally, a tripod is necessary to steady your camera when shooting a night scene. However, with the (Handheld Night Scene) mode, you can shoot night scenes while handholding the camera. In this mode, four shots are taken continuously for each picture, and a resulting bright image with reduced camera shake is recorded. Shooting Tips PY O C Hold the camera firmly. While shooting, hold the camera firmly and steadily.
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the (HDR Backlight Control) mode. When you take a picture, three continuous shots are taken at different exposures, and the resulting image with the least loss of shadow detail due to backlighting and widest tonal range is recorded. Shooting Tips PY O C Hold the camera firmly. While shooting, hold the camera firmly and steadily. If any of the three shots are greatly misaligned due to camera shake, etc.
Cautions for (Handheld Night Scene) During Live View shooting, it may be difficult to focus dots of light such as in a night scene. In such a case, you should set the AF method to [Quick mode] and shoot. If it is still difficult to focus, set the lens’ focus mode switch to [MF] and focus manually. When shooting flash photography, if the subject is too close to the camera, the picture may come out extremely bright (overexposure).
Q Quick Control In Basic Zone modes when the shooting function settings screen is displayed, you can press the button to display the Quick Control screen. The table below indicates the functions that can be set with the Quick Control screen in each Basic Zone mode. Example: Portrait mode 1 Set the Mode Dial to a Basic Zone mode. 2Press the button. (7) The Quick Control screen will appear. 3 Set the function. Press the key to select a function. (This step is not necessary in the A mode.
Shoot by Ambience Selection Except in the and Basic Zone modes, you can select the ambience for shooting. Ambience C Standard setting k k k k k k k k k Vivid Soft Warm Intense Cool Brighter Darker Monochrome 8 4 5 k k k k k k k k k k k k k k k k k k 6 k k k k k k k k k F k k k k k k k k k Ambience Effect 2 k k k k k k k k k 3 k k k k k k k k k 1 Set the shooting mode to or <8>.
Shoot by Ambience Selection Press the key to select the desired ambience. The LCD monitor will display how the image will look with the selected ambience. the ambience effect. 5 SetPress the key to select the effect bar so that [Effect] appears at the bottom. Press the key to select the desired effect. the picture. 6 TakePress the shutter button completely to take the picture. To return to viewfinder shooting, press the <0> button to exit Live View shooting.
Shoot by Ambience Selection Ambience Settings Standard setting Standard image characteristics for the respective shooting mode. Note that <2> has image characteristics geared for portraits and <3> is geared for landscapes. Each ambience is a modification of the respective shooting mode’s image characteristics. Vivid The subject will look sharp and vivid. It makes the photo look more impressive than with [ Standard setting]. Soft The subject will look softer and more dainty.
Shoot by Lighting or Scene Type In the <2>, <3>, <4>, and <5> Basic Zone modes, you can shoot while the settings match the lighting or scene type. Normally, [ Default setting] is adequate, but if the settings match the lighting condition or scene, the picture will look more accurate to your eye. For Live View shooting, if you set both [Light/scene-based shots] and [Ambience-based shots] (p.84), you should first set [Light/scenebased shots].
Shoot by Lighting or Scene Type the Quick Control screen, 4 On select the lighting or scene type. Press the button (7). Press the key to select [ Default setting]. [Light/scenebased shots] will appear on the screen. Press the key to select the desired lighting or scene type. The resulting image with the selected lighting or scene type will be displayed. the picture. 5 TakePress the shutter button completely to take the picture.
Shoot by Lighting or Scene Type Lighting or Scene Type Settings Default setting Default setting suited for most subjects. Daylight For subjects under sunlight. Gives more natural-looking blue skies and greenery and reproduces light-colored flowers better. Shade For subjects in the shade. Suitable for skin tones, which may look too bluish, and for light-colored flowers. Cloudy For subjects under overcast skies. Makes skin tones and landscapes, which may otherwise look dull on a cloudy day, look warmer.
PY O C
Setting the AF and Drive Modes The viewfinder has 11 AF points. By selecting the optimum AF point, you can compose the picture as desired while autofocusing. PY O C You can also select the AF operation and drive mode that best match the shooting conditions and subject. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). In Basic Zone modes, the AF operation and AF point are set automatically. stands for autofocus.
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. 1 Set the lens focus mode switch to . the Mode Dial to a Creative 2 Turn Zone mode. 3 Press the button. (9) the AF operation. 4 Select Y at the LCD panel, turn WhileP looking theO <6> or <5> dial.
f: Selecting the AF OperationN If focus cannot be achieved, the focus confirmation light in the viewfinder will blink. If this occurs, the picture cannot be taken even if the shutter button is pressed completely. Recompose the shot and try to focus again, or see “When Autofocus Fails” (p.96). If [z1: Beep] is set to [Disable], the beeper will not sound when focus is achieved. After achieving focus with One-Shot AF, you can lock the focus on a subject and recompose the shot. This is called “focus lock”.
S Selecting AF PointsN You can select an AF point for focusing from among eleven AF points. In Basic Zone modes, the AF point will be selected automatically and you cannot select the AF point. 1 Press the button. (9) The selected AF point will be displayed in the viewfinder and on the LCD panel. When all the AF points light up, automatic AF point selection will be set. an AF point. 2 Select You can either use <9> or turn the <6> or <5> dial to select an AF point.
S Selecting AF PointsN Selecting with the Dials Turn the <6> dial to select an AF point on the left or right or turn the <5> dial to select an AF point above or below. If all the AF points light up, automatic AF point selection will be set.
When Autofocus Fails Autofocus can fail to achieve focus (viewfinder’s focus confirmation light blinks) with certain subjects such as the following: Subjects difficult to focus Very low-contrast subjects (Example: Blue sky, solid-color walls, etc.) Subjects in very low light Extremely backlit and reflective subjects (Example: Car with a highly reflective body, etc.) Near and far subjects covered by an AF point (Example: Animal in a cage, etc.
When Autofocus Fails MF: Manual Focusing 1 Set the lens focus mode switch to . <4 L> will be displayed on the LCD panel. Focusing ring the subject. 2 Focus Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder. PY O C If you press the shutter button halfway during manual focusing, the AF point which achieved focus will flash briefly in red and the focus confirmation light will light up in the viewfinder.
i Selecting the Drive Mode Single and continuous drive modes are provided. 1 Press the button. (9) the drive mode. 2 Select While looking at the LCD panel, turn the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken. i : Continuous shooting (Max. approx. 4.5 shots/sec.) While you hold down the shutter button completely, shots will be taken continuously. B : Silent single shooting Single shooting with less shooting sound than .
i Selecting the Drive Mode If or is set, the time lag from when you press the shutter button completely until the picture is shot will be longer than with normal single or continuous shooting. When the battery level is low, the continuous shooting speed may become slightly slower. In AI Servo AF operation, the continuous shooting speed may become slightly slower depending on the subject and the lens used. i: The maximum continuous shooting speed of approx. 4.5 shots/sec.
j Using the Self-timer Use the self-timer when you want to be in the picture. 1 Press the button. (9) the self-timer. 2 Select While looking at the LCD panel, turn the <6> or <5> dial to select the self-timer delay. Q : 10-sec. self-timer k : 2-sec. self-timer picture. 3 TakeLookthethrough the viewfinder, focus the subject, then press the shutter button completely. You can check the self-timer operation with the self-timer lamp, beeper, and countdown display (in seconds) on the LCD panel.
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. PY O C In Basic Zone modes, only the following can be set as described in this chapter: Image-recording quality, lens peripheral illumination and chromatic aberration correction, folder creation and selection, and image file numbering.
3 Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.104). 1 Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>. the image-recording quality. 2 Select To select a RAW setting, turn the <6> dial. To select a JPEG setting, press the key.
3 Setting the Image-Recording Quality Guide to Image-Recording Quality Settings (Approx.) Image Quality 73 83 74 JPEG 84 7a Pixels File Size Possible Printing Size Recorded (MB) Shots 20M A2 8.9M A3 Maximum Burst 6.0 1250 73 (1250) 3.1 2380 2380 (2380) 3.2 2300 2300 (2300) 1.7 4240 4240 (4240) 2.1 3450 3450 (3450) 1.1 6370 6370 (6370) 5.0M A4 b*1 2.5M 9x13 cm 1.2 6130 6130 (6130) c*2 0.3M - 0.3 23070 23070 (23070) 1 14 (17) 8a 20M A2 23.
3 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded simultaneously to the card in both RAW and JPEG at the imagerecording quality that was set. The two images will be recorded with the same file numbers (file extension .JPG for JPEG and .CR2 for RAW). The image-recording quality icons are as follows: 1 (RAW), 41 (Medium RAW), 61 (Small RAW), JPEG, 7 (Fine), 8 (Normal), 3 (Large), 4 (Medium), and 6 (Small).
3 Setting the Image-Recording Quality Maximum Burst During Continuous Shooting The approximate maximum burst is displayed on the bottom right in the viewfinder and on the shooting function settings screen. If the maximum burst for continuous shooting is 99 or higher, “99” will be displayed. PY O C The maximum burst is displayed even when a card is not inserted in the camera. Make sure that a card is inserted before taking a picture.
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically (p.108). Regarding the ISO speed during movie shooting, see pages 206 and 209. 1 Press the button. (9) the ISO speed. 2 SetWhile looking at the LCD panel or the viewfinder, turn the <6> or <5> dial. ISO speed can be set within ISO 100 - 25600 in 1/3-stop increments. “A” indicates ISO Auto. The ISO speed will be set automatically (p.
i: Setting the ISO SpeedN If [z4: Highlight tone priority] is set to [Enable], you cannot select “L” (equivalent to ISO 50), ISO 100/125/160, “H1” (equivalent to ISO 51200), and “H2” (equivalent to ISO 102400) (p.130). Shooting in high temperatures may result in images that look grainier. Long exposures can also cause irregular colors in the image. When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable.
i: Setting the ISO SpeedN ISO Auto If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within L (ISO 50) to H1 (ISO 51200), and the maximum limit within ISO 100 to H2 (ISO 102400). 1 Select [ISO speed settings]. Under the [z3] tab, select [ISO speed settings], then press <0>. [ISO speed range]. 2 Select Select [ISO speed range], then press <0>. PY O Set the minimum limit. 3 C Select the minimum limit box, then press <0>.
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range for Auto ISO You can set the automatic ISO speed range for Auto ISO within ISO 100 - 25600. You can set the minimum limit within ISO 100 - 12800, and the maximum limit within ISO 200 - 25600 in whole-stop increments. 1 Select [Auto ISO range]. Select [Auto ISO range], then press <0>. the minimum limit. 2 SetSelect the minimum limit box, then press <0>. Press the key to select an ISO speed, then press <0>. PY O C the maximum limit.
i: Setting the ISO SpeedN 3 Setting the Minimum Shutter Speed for Auto ISO When Auto ISO is set, you can set the minimum shutter speed (1/250 sec. to 1 sec.) so that the automatically-set shutter speed is not too slow. This is convenient in the and modes when you use a wideangle lens to shoot a moving subject. You can minimize both camera shake and subject blur. 1 Select [Min. shutter spd.]. Select [Min. shutter spd.], then press <0>. the desired minimum shutter 2 Set speed.
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, (Auto) is set automatically. 1 Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>. The Picture Style selection screen will appear. a Picture Style. 2 Select Press the key to select a Picture Style, then press <0>. The Picture Style will be set and the camera will be ready to shoot.
A Selecting a Picture StyleN R Landscape For vivid blues and greens, and very sharp and crisp images. Effective for impressive landscapes. S Neutral This Picture Style is for users who prefer to process images with their computer. For natural colors and subdued images. U Faithful This Picture Style is for users who prefer to process images with their computer. When the subject is captured under a color temperature of 5200K, the color is adjusted colorimetrically to match the subject’s color.
A Selecting a Picture StyleN About the Symbols The symbols of the Picture Style selection screen refer to parameters such as [Sharpness] and [Contrast]. The numerals indicate the parameter settings, such as for [Sharpness] and [Contrast], for each Picture Style.
A Customizing a Picture StyleN You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see page 117. 1 Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>. The Picture Style selection screen will appear. a Picture Style. 2 Select Select a Picture Style, then press the button. PY O 3C Select a parameter.
A Customizing a Picture StyleN Parameter Settings and Effects g Sharpness 0: Less sharp outline +7: Sharp outline h Contrast -4: Low contrast +4: High contrast i Saturation -4: Low saturation +4: High saturation j Color tone -4: Reddish skin tone +4: Yellowish skin tone PY O C By selecting [Default set.] in step 3, you can revert the respective Picture Style to its default parameter settings. To use the adjusted Picture Style, first select the adjusted Picture Style, then shoot.
A Customizing a Picture StyleN V Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page. kFilter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more. Filter Sample Effects N: None Normal black-and-white image with no filter effects. Ye: Yellow The blue sky will look more natural, and the white clouds will look crisper.
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create multiple Picture Styles whose parameter settings such as sharpness and contrast are different. You can also adjust the parameters of a Picture Style that has been registered to the camera with EOS Utility (provided software, p.392). 1 Select [Picture Style].
A Registering a Picture StyleN a parameter. 5 Select Select a parameter such as [Sharpness], then press <0>. the parameter. 6 SetPress the key to adjust the parameter as desired, then press <0>. For details, see “Customizing a Picture Style” on pages 115-117. Press the button to register the modified Picture Style. The Picture Style selection screen will then reappear. The base Picture Style will be indicated on the right of [User Def. *].
3 Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the (Auto) setting will obtain the correct white balance. If naturallooking colors cannot be obtained with , you can select the white balance to match the light source or set it manually by shooting a white object. In Basic Zone modes, is set automatically. 1 Select [White balance]. Under the [z3] tab, select [White balance], then press <0>. the white balance.
3 Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Perform this procedure under the actual light source to be used. 1 Photograph a white object. The plain, white object should fill the spot metering circle. Focus manually and set the standard exposure for the white object. You can set any white balance. Spot metering circle [Custom White Balance].
3 Setting the White BalanceN If the exposure obtained in step 1 differs greatly from the standard exposure, a correct white balance may not be obtained. In step 3, the following images cannot be selected: images captured while the Picture Style was set to [Monochrome], multiple-exposure images, and images shot with another camera. Instead of a white object, an 18% gray card (commercially available) can produce a more accurate white balance.
3 White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters. White Balance Correction 1 Select [WB Shift/Bkt.]. Under the [z3] tab, select [WB Shift/Bkt.], then press <0>.
3 White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images having a different color tone can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to ±3 levels in single-level increments. Set the white balance bracketing amount.
3 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically. 1 Select [Auto Lighting Optimizer]. Under the [z3] tab, select [Auto Lighting Optimizer], then press <0>. the setting.
3 Noise Reduction SettingsN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced. 1 Select [High ISO speed NR]. Under the [z4] tab, select [High ISO speed NR], then press <0>. the level. 2 SetSelect the desired noise reduction level, then press <0>.
3 Noise Reduction SettingsN About [Multi Shot Noise Reduction] The following functions cannot be set: AEB, WB bracketing, [z4: Long exp. noise reduction], [z4: HDR Mode], [z4: Multiple exposure], and RAW image. If any of these has already been set, [Multi Shot Noise Reduction] cannot be set. Flash shooting is not possible. The AF-assist beam will be emitted according to the [8C.Fn II -5: AF-assist beam firing] setting. You cannot set [Multi Shot Noise Reduction] for bulb exposures.
3 Noise Reduction SettingsN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. 1 Select [Long exp. noise reduction]. Under the [z4] tab, select [Long exp. noise reduction], then press <0>. the desired setting. 2 SetSelect the desired setting, then press <0>. The setting screen closes and the menu will reappear. PY O C [Auto] For 1 sec. or longer exposures, noise reduction is performed automatically if noise typical of long exposures is detected.
3 Noise Reduction SettingsN With [Auto] and [Enable], the noise reduction process after the picture is taken may take the same amount of time as that for the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1” or higher. Images taken at ISO 1600 or higher may look grainier with the [Enable] setting than with the [Disable] or [Auto] setting.
3 Highlight Tone PriorityN You can minimize overexposed highlight areas. 1 Select [Highlight tone priority]. Under the [z4] tab, select [Highlight tone priority], then press <0>. [Enable]. 2 Select Select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights. The gradation between the grays and highlights becomes smoother. PY the picture. O 3 Take CThe image will be recorded with highlight tone priority applied.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. Both lens aberrations can be corrected. The default settings are [Enable] for both corrections. Peripheral Illumination Correction 1 Select [Lens aberration correction]. Under the [z2] tab, select [Lens aberration correction], then press <0>. the setting.
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction 1 Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “About the Lens Correction Data” on the next page. picture. 2 TakeThetheimage will be recorded with the chromatic aberration corrected.
3 Lens Peripheral Illumination / Chromatic Aberration Correction About the Lens Correction Data The camera already contains lens peripheral illumination correction data and chromatic aberration correction data for approx. 25 lenses. If you select [Enable], the peripheral illumination correction and chromatic aberration correction will be applied automatically for any lens whose correction data is registered in the camera.
3 Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder 1 Select [Select folder]. Under the [51] tab, select [Select folder], then press <0>. [Create folder]. 2 Select Select [Create folder], then press <0>. PY O C Create a new folder. 3 Select [OK], then press <0>.
3 Creating and Selecting a Folder Selecting a Folder Lowest file number Number of images in folder With the folder selection screen displayed, select a folder and press <0>. The folder where the captured images will be saved is selected. Subsequent captured images will be recorded into the selected folder. Folder name Highest file number About Folders PY O C As with “100CANON” for example, the folder name starts with three digits (the folder number) followed by five alphanumeric characters.
3 File Numbering Methods The image files will be numbered from 0001 to 9999 in the order the images are taken, then saved in a folder. You can change how the file number is assigned. The file number will appear on your computer in this format: IMG_0001.JPG. 1 Select [File numbering]. Under the [51] tab, select [File numbering], then press <0>. the file numbering method. 2 Select Select the desired setting, then press <0>.
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. When you replace the card or create a folder, the file numbering restarts from 0001 for the new images saved. This is convenient if you want to organize images according to cards or folders.
3 Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. 1 Select [Copyright information]. Under the [54] tab, select [Copyright information], then press <0>. the option to be set. 2 Select Select [Enter author’s name] or [Enter copyright details], then press <0>. text. 3 Enter PtheY button, and the text Press O Cpalette will be highlighted in a color frame. Text can be entered.
3 Setting Copyright InformationN Checking the Copyright Information When you select [Display copyright info.] in step 2 on the preceding page, you can check the [Author] and [Copyright] information that you entered. Deleting the Copyright Information When you select [Delete copyright information] in step 2 on the preceding page, you can delete the [Author] and [Copyright] information. PY O C You can also set or check the copyright information with EOS Utility (provided software, p.392).
3 Setting the Color SpaceN The range of reproducible colors is called the color space. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In Basic Zone modes, sRGB is set automatically. 1 Select [Color space]. Under the [z3] tab, select [Color space], then press <0>. the desired color space. 2 SetSelect [sRGB] or [Adobe RGB], then press <0>.
Advanced Operations In Creative Zone modes, you can set the shutter speed and/or aperture to set the exposure as desired. By changing the camera settings, you can obtain various results. PY O C The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F). After you press the shutter button halfway and let go, the exposure values will remain displayed in the viewfinder and on the LCD panel for 4 sec. (0).
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * stands for Program. * AE stands for Auto Exposure. 1 Set the Mode Dial to . the subject. 2 Focus Look through the viewfinder and aim the selected AF point over the subject. Then press the shutter button halfway.
d: Program AE If the “30"” shutter speed and the lower f/number blink, it indicates underexposure. Increase the ISO speed or use flash. If the “4000” shutter speed and the higher f/number blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens. Differences Between and Modes In the mode, many functions such the AF operation and metering mode are set automatically to prevent spoiled shots.
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion. * stands for Time value. Blurred motion (Slow shutter speed: 1/30 sec.) 1 Frozen action (Fast shutter speed: 1/2000 sec.
s: Shutter-Priority AE If the lower f/number blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the higher f/number blinks, it indicates overexposure. Turn the <6> dial to set a faster shutter speed until the aperture stops blinking or set a lower ISO speed. Shutter Speed Display The shutter speeds from “4000” to “4” indicate the denominator of the fractional shutter speed.
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus. On the other hand, a lower f/number (larger aperture hole) will make less of the foreground and background fall within acceptable focus.
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/ number) until the shutter speed blinking stops or set a higher ISO speed. If the “4000” shutter speed blinks, it indicates overexposure. Turn the <6> dial to set a smaller aperture (higher aperture f/number) until the shutter speed blinking stops or set a lower ISO speed. Aperture Display The higher the f/number, the smaller the aperture opening will be.
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * stands for Manual. 1 Set the Mode Dial to . 2 Set the ISO speed (p.106). speed and aperture. 3 SetTothesetshutter the shutter speed, turn the <6> dial. To set the aperture, turn the <5> dial.
q Selecting the Metering ModeN In [z3: Auto Lighting Optimizer], if the checkmark for [Disabled in M or B modes] is removed, Auto Lighting Optimizer can be set in the and modes (p.125). When ISO Auto is set, you can press the button to lock the ISO speed. If you press the button and recompose the shot, you can see the exposure level difference on the exposure level indicator (p.22, 23) compared to when the button was pressed.
q Selecting the Metering ModeN r Spot metering This is for metering a specific spot of the subject or scene. The metering is weighted at the center covering approx. 3.5% of the viewfinder area. e Center-weighted average metering The metering is weighted at the center and then averaged for the entire scene. PY O C With q (Evaluative metering), the exposure setting will be locked when you press the shutter button halfway and focus is achieved.
Setting Exposure Compensation N Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. 1 Select [Expo.comp./AEB]. Under the [z3] tab, select [Expo.comp./AEB], then press <0>. the AEB range. 2 SetTurn the <6> dial to set the AEB AEB range range. Press the key to set the exposure compensation amount. Press <0> to set it.
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the button to lock the exposure, then recompose and take the shot. This is called AE lock. It is effective for backlit subjects. 1 Focus the subject. Press the shutter button halfway. The exposure setting will be displayed. the button.
F: Bulb Exposures When bulb is set, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, astronomical objects, and other subjects requiring long exposures. 1 Set the Mode Dial to . the desired aperture. 2 SetWhile looking at the LCD panel, turn the <6> or <5> dial. 3 Take the picture.
w: HDR (High Dynamic Range) ShootingN You can shoot images preserving a wide tonal range where the highlight and shadow detail would otherwise be lost. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured for each shot and then merged together automatically. The HDR image is recorded as a JPEG image. HDR Shooting 1 Select [HDR Mode].
w: HDR (High Dynamic Range) ShootingN [Continuous HDR]. 3 SetSelect either [1 shot only] or [Every shot], then press <0>. With [1 shot only], HDR shooting will be canceled automatically after the shooting ends. With [Every shot], HDR shooting continues until the setting in step 2 is set to [Disable HDR]. Image Align]. 4 SetFor[Auto handheld shooting, select [Enable]. When using a tripod, select [Disable]. Then, press <0>. Y the picture.
w: HDR (High Dynamic Range) ShootingN If you shoot a moving subject, the subject’s movement will leave afterimages. To prevent camera shake, the ISO speed may be set higher than usual. HDR shooting is not possible with ISO expansion. (HDR shooting is possible within the range of ISO 100 - 25600.) When shooting HDR images with [Auto Image Align] set to [Enable], AF point display information (p.240) and Dust Delete data (p.281) will not be appended to the image.
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.179), you can see how the single exposures merge while shooting. 1 Select [Multiple exposure]. Under the [z4] tab, select [Multiple exposure], then press <0>. The multiple exposure setting screen will appear. [Multiple exposure]. 2 SetSelect [Enable], then press <0>. To exit shooting multiple exposures, select [Disable].
P Multiple ExposuresN [Multi-expos ctrl]. 3 SetSelect the desired multiple-exposure control method, then press <0>. Additive The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation. Exposure Compensation Setting Guide for Multiple Exposures Two exposures: -1 stop, three exposures: -1.
P Multiple ExposuresN [Continue Mult-exp]. 5 SetSelect either [1 shot only] or [Continuously], then press <0>. With [1 shot only], multiple-exposure shooting will be canceled automatically after the shooting ends. With [Continuously], multipleexposure shooting continues until the setting in step 2 is set to [Disable]. first exposure. 6 TakeThethecaptured image will be displayed. Remaining number of exposures The
icon will blink.
P Multiple ExposuresN Only the merged multiple-exposure image will be saved. The images taken in steps 6 and 7 for the multiple-exposure image will not be saved. With multiple exposures, the more exposures there are, the more noticeable the noise, irregular colors, and banding will be. Also, as noise increases with higher ISO speeds, shooting at low ISO speeds is recommended. If [Additive] is set, the image processing after taking the multiple exposures will take time.
P Multiple ExposuresN Merging Multiple Exposures with an Image Recorded in the Card You can select an image recorded in the card as the first single exposure. The original of the selected image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images. 1 Select [Select image for multi. expo.]. Select [Select image for multi. expo.], then press <0>. The images in the card will be displayed. an image.
P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single exposure. If you select [Deselect img], the selected image will be canceled. Checking and Deleting Multiple Exposures During Shooting Before you finish shooting the set number of exposures, you can press the button to view the merged multiple-exposure image so far. You can check how it looks and the exposure. If you press the button, the operations possible during multipleexposure shooting will be displayed.
P Multiple ExposuresN FAQ Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Image-Recording Quality Setting Merged Multiple-Exposure JPEG JPEG 1 1 41/61 1 1+JPEG 1+JPEG 41/61+JPEG 1+JPEG Can I merge images recorded in the card? With [Select image for multi. expo.], you can select the first single exposure from the images recorded on the card (p.162).
2 Mirror LockupN Although using the self-timer or Remote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). 1 Set [Mirror lockup] to [Enable]. Under the [z2] tab, select [Mirror lockup], then press <0>. Select [Enable], then press <0>. 2Focus the subject, then press the shutter button completely. The mirror will swing up. 3 Press the shutter button completely again.
Using the Eyepiece Cover When you use the self-timer, bulb, or Remote Switch and do not look through the viewfinder, stray light entering the viewfinder can cause the image to look dark. To prevent this, use the eyepiece cover (p.27) attached to the camera strap. During Live View shooting and movie shooting, attaching the eyepiece cover is unnecessary. 1 Detach the eyecup. Push the bottom of the eyecup to detach. the eyepiece cover.
F Using a Remote Switch You can connect the Remote Switch RS-80N3, Timer Remote Controller TC-80N3 (both sold separately), or any EOS accessory equipped with an N3-type terminal to the camera for shooting (p.354). To operate the accessory, refer to its instruction manual. 1 Open the terminal cover. the plug to the remote 2 Connect control terminal. Connect the plug as shown in the illustration. To disconnect the plug, grasp the silver part and pull.
R Remote Control Shooting 3 Press the button. (9) the self-timer. 4 Select Look at the LCD panel and turn the <6> dial to select or . the remote controller’s 5 Press transmit button. Remote control sensor Point the remote controller toward the camera’s remote control sensor and press the transmit button. The self-timer lamp lights up and the picture is taken. PY O C Fluorescent or LED lighting may cause camera misoperation by triggering the shutter inadvertently.
Flash Photography This chapter explains how to shoot with an EOSdedicated, EX-series Speedlite (sold separately) or nonCanon flash unit and how to set flash functions on the camera’s menu screen.
D Flash Photography EOS-dedicated, EX-series Speedlites An EX-series Speedlite (sold separately) makes flash photography as easy as normal shooting. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions with the camera’s menu, see pages 172-177.
D Flash Photography Canon Speedlites Other Than the EX-series With an EZ/E/EG/ML/TL-series Speedlite set to A-TTL or TTL autoflash mode, the flash can be fired at full output only. Set the camera’s shooting mode to (manual exposure) or (aperture-priority AE) and adjust the aperture setting before shooting. When using a Speedlite that has manual flash mode, shoot in the manual flash mode.
3 Setting the FlashN With an EX-series Speedlite having compatible flash function settings, you can use the camera’s menu screen to set the Speedlite’s functions and Custom Functions. Attach the Speedlite to the camera and turn on the Speedlite before starting these settings. For details on the Speedlite’s functions, refer to the Speedlite’s instruction manual. 1 Select [External Speedlite control]. Under the [z2] tab, select [External Speedlite control], then press <0>.
3 Setting the FlashN Flash Synchronization Speed in Av Mode You can set the flash-sync speed for flash photography in the aperture-priority AE (f) mode. : Auto The flash sync speed is set automatically within a range of 1/180 sec. to 30 sec. to suit the scene’s brightness. High-speed sync is also possible. : 1/180-1/60 sec. auto Prevents a slow shutter speed from being set in low-light conditions. It is effective for preventing subject blur and camera shake.
3 Setting the FlashN Flash Function Settings On the screen, the settable functions and the display will differ depending on the Speedlite, current flash mode, flash Custom Function settings, etc. For details on your Speedlite’s flash functions, refer to the Speedlite’s instruction manual.
3 Setting the FlashN Wireless functions Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the Speedlite’s instruction manual. Flash zoom (Flash coverage) With Speedlites having a zooming flash head, you can set the flash coverage. Normally, set this to [AUTO] so that the camera will automatically set the flash coverage to match the lens focal length.
3 Setting the FlashN Flash exposure compensation The same setting as “Flash exposure compensation” on page 170 can be set. For details, refer to the Speedlite’s instruction manual. Flash exposure bracketing While the flash output is changed automatically, three shots are taken. For details, refer to the instruction manual of a Speedlite compatible with flash exposure bracketing. PY O C When using second-curtain synchronization, set the shutter speed to 1/25 sec. or slower.
3 Setting the FlashN Flash Custom Function Settings For details on the Speedlite’s Custom Functions, refer to the Speedlite’s instruction manual. 1 Select [Flash C.Fn settings]. Select [Flash C.Fn settings], then press <0>. the functions. 2 SetPress the key to select the number, then press <0>. Select the setting, then press <0>. Clear Settings PY O 1C Select [Clear settings]. Under the [z2: External Speedlite control] tab, select [Clear settings], then press <0>. the settings to be cleared.
PY O C
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to . PY O C Live View shooting is effective for photos of still subjects. If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images. Using a tripod is recommended.
A Shooting with the LCD Monitor 1 Set the Live View shooting/Movie shooting switch to . the Live View image. 2 Display Press the <0> button. The Live View image will appear on the LCD monitor. The Live View image will closely reflect the brightness level of the actual image you capture. the subject. 3 Focus When you press the shutter button halfway, the camera will focus with the current PY AF method (p.192). O C the picture. 4 TakePress the shutter button completely.
A Shooting with the LCD Monitor Enabling Live View Shooting Set [A1: Live View shoot.] to [Enable]. Number of Possible Shots with Live View Shooting [Approx. number of shots] Temperature Room Temperature ( 23°C / 73°F) Low Temperature (0°C / 32°F) Possible shots 220 190 The figures above are based on a fully-charged Battery Pack LP-E6 and CIPA (Camera & Imaging Products Association) testing standards. With a fully-charged Battery Pack LP-E6, continuous Live View shooting is possible for approx.
A Shooting with the LCD Monitor About the Information Display Each time you press the button, the information display will change.
A Shooting with the LCD Monitor Scene Icons During Live View shooting in the mode, an icon representing the scene detected by the camera will be displayed and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
A Shooting with the LCD Monitor *5: Displayed with any of the lenses below: • EF24mm f/2.8 IS USM • EF28mm f/2.8 IS USM • EF300mm f/2.8L IS II USM • EF400mm f/2.8L IS II USM • EF500mm f/4L IS II USM • EF600mm f/4L IS II USM • Image Stabilizer lenses marketed in 2012 or later. *4 and *5: If the conditions in both *4 and *5 apply, the shutter speed will become slow (as slow as 2 sec.). Final Image Simulation The final image simulation reflects the effects of the Picture Style, white balance, etc.
Shooting Function Settings Q Quick Control If you press the button while the Live View image is displayed in a Creative Zone mode, you can set any of the following: AF method, drive mode, metering mode, image-recording quality, white balance, Picture Style, and Auto Lighting Optimizer. In Basic Zone modes, you can set the functions in bold and the settings shown in the table on page 83. 1 Press the button. The settable functions will be displayed. a function and set it.
Shooting Function Settings f / R / i / q / S Settings While the Live View image is displayed, if you press the , , , or button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function. When Quick mode is set, you can press the button to select the AF point. The operation procedure is the same as with viewfinder shooting.
3 Menu Function Settings [A1] Menu Function settings particular to Live View shooting are explained here. Details of menu items under the [A1] and [A2] tabs are on pages 187-191. In Basic Zone modes, certain items under the [A1] tab will not appear and the [A2] tab will not appear. The settable functions on this menu screen apply only to Live View shooting. These functions do not take effect during viewfinder shooting. Live View shooting You can set Live View shooting to [Enable] or [Disable].
3 Menu Function Settings Aspect ratioM The image’s aspect ratio can be set to [3:2], [4:3], [16:9], or [1:1]. The area surrounding the Live View image is masked in black when the following aspect ratios are set: [4:3] [16:9] [1:1]. JPEG images will be saved with the set aspect ratio. RAW images will always be saved with the [3:2] aspect ratio.
3 Menu Function Settings Exposure simulationN Exposure simulation simulates and displays how the brightness of the actual image (exposure) will look. ・ Enable (g) The displayed image brightness will be close to the actual brightness (exposure) of the resulting image. If you set exposure compensation, the image brightness will change accordingly. ・ During e Normally, the image is displayed at the standard brightness to make the Live View image easy to see.
3 Menu Function Settings [A2] Menu Silent LV shootingN • Mode 1 The shooting operation noise is quieter than with normal shooting. Continuous shooting is also possible. If is set, you can shoot at a maximum continuous shooting speed of approx. 4.1 fps. • Mode 2 When the shutter button is pressed completely, only one shot will be taken. While you keep holding down the shutter button, the camera operation will be suspended.
3 Menu Function Settings Metering timerN You can change how long the exposure setting is displayed (AE lock time). PY O C The Live View shooting will stop with any of the following operations. To resume Live View shooting, press the <0> button again. • When [z4: Dust Delete Data], [54: Sensor cleaning], [54:Clear all camera settings], or [54: z Firmware ver.
Using AF to Focus (AF Method) Selecting the AF Method The AF methods available are [FlexiZoneAF (Single)], [u Live mode] (face detection, p.193), and [Quick mode] (p.197). If you want to achieve precise focus, set the lens focus mode switch to , magnify the image, and focus manually (p.199). Select the AF method. Under the [A1] tab, select [AF method]. While the Live View image is displayed, you can also press the button to select the AF method on the setting screen.
Using AF to Focus (AF Method) the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the AF point will turn orange. the picture. 4 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.180). PY O This is the same AF method as Cwith FlexiZone - Single.
Using AF to Focus (AF Method) the subject. 2 Focus Press the shutter button halfway and the camera will focus the face covered by the
frame. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the AF point will turn orange. If a face cannot be detected, the AF point < > will be displayed and AF will be executed at the center. the picture. 3 TakeCheck the focus and exposure, then press the shutter button completely to take the PYpicture (p.180).
Using AF to Focus (AF Method) FlexiZone - Single and u (Face Detection) Live Mode Notes AF Operation Focusing will take slightly longer. Even when focus has been achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation. If the light source changes while the Live View image is displayed, the screen may flicker and focusing may be difficult. If this happens, exit Live View shooting and autofocus under the actual light source.
Using AF to Focus (AF Method) Shooting conditions that make focusing difficult Low-contrast subjects such as the blue sky and solid-color, flat surfaces. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction. Under a light source whose brightness, color, or pattern keeps changing. Night scenes or points of light. Under fluorescent or LED light sources and when the image flickers. Extremely small subjects. Subjects at the edge of the picture.
Using AF to Focus (AF Method) Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.92), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation. You can use eleven AF points to focus (automatically selected). You can also select one AF point to focus and focus only the area covered by that AF point (manually selected).
Using AF to Focus (AF Method) the subject. 3 Focus Aim the AF point over the subject and press the shutter button halfway. The Live View image will turn off, the reflex mirror will go back down, and AF will be executed. (No picture is taken.) When focus is achieved, the beeper will sound and the Live View image will reappear. The AF point used to focus will light up in green. If focus is not achieved, the AF point will blink in orange. the picture.
Focusing Manually You can magnify the image and focus precisely with manual focus. 1 Set the lens focus mode switch to . Turn the lens focusing ring to focus roughly. the magnifying frame. 2 Display Press the button. Magnifying frame the magnifying frame. Y<9> to move the magnifying 3 Move P Press O to the position where you want C frame to focus. To return the magnifying frame to the center, press <0> or the button. the image.
Focusing Manually manually. 5 Focus While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. the picture. 6 TakeCheck the focus and exposure, then press the shutter button completely to take the picture (p.180).
Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a long period, the camera’s internal temperature may rise, and image quality may deteriorate. Stop Live View shooting when not shooting images.
Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. If the light source (illumination) within the image changes, the screen may flicker. If this happens, exit Live View shooting and resume shooting under the actual light source. If you point the camera to a different direction, it may throw off the Live View image’s correct brightness momentarily.
Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to . The movie recording format will be MOV. PY O C For cards which can record movies, see page 3. Under the [53] tab, if you set [Wi-Fi] to [Enable], you cannot shoot movies. Before shooting movies, set [Wi-Fi] to [Disable].
k Shooting Movies Autoexposure Shooting When the shooting mode is set to other than , autoexposure control will take effect to suit the scene’s current brightness. 1 Set the shooting mode. Set the Mode Dial to any shooting mode except . the Live View shooting/Movie 2 Set shooting switch to . The reflex mirror will make a sound, then the image will appear on the LCD monitor. the subject. 3 Focus Before shooting a movie, focus with Y focus (p.192-200).
k Shooting Movies Cautions for movie shooting are on pages 233 and 234. If necessary, also read the Live View shooting cautions on pages 201 and 202. In Basic Zone modes, the shooting result will be the same as in the mode. Also, the scene icon for the scene detected by the camera is displayed on the upper left (p.207). In the , , or shooting modes, the settings will be the same as in the mode. Settable menu functions will differ between Basic Zone modes and Creative Zone modes (p.353).
k Shooting Movies ISO speed in Basic Zone modes The ISO speed will be set automatically within ISO 100 - 12800. ISO speed in Creative Zone modes The ISO speed will be set automatically within ISO 100 - 12800. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [25600/H] (p.109), the maximum ISO speed for the automatic ISO speed setting will be expanded to H (equivalent to ISO 25600).
k Shooting Movies Scene Icons During movie shooting in a Basic Zone mode, an icon representing the scene detected by the camera will be displayed and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. 1 Set the Mode Dial to . the Live View shooting/Movie 2 Set shooting switch to . the ISO speed. 3 SetPress the button. The ISO speed setting screen will appear on the LCD monitor. Turn the <6> dial to set the ISO speed. For details on the ISO speed, see the next page. PY O C the shutter speed and aperture.
k Shooting Movies ISO speed during manual-exposure shooting With [Auto] (A), the ISO speed will be set automatically within ISO 100 - 12800. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [25600/H], the maximum ISO speed will be expanded and the ISO speed will be set automatically within ISO 100 to H. You can set the ISO speed manually within ISO 100 - 12800 in 1/3-stop increments.
k Shooting Movies Information Display Each time you press the button, the information display will change.
k Shooting Movies Notes on Movie Shooting The camera cannot autofocus continuously like a camcorder. Autofocusing during movie shooting is not recommended since it may momentarily throw the focus far off or change the exposure. During movie shooting, do not point the lens toward the sun. The sun’s heat can damage the camera’s internal components. If is set and the ISO speed or aperture changes during movie shooting, the white balance may also change.
k Shooting Movies Notes on Movie Shooting You can use Remote Controller RC-6 (sold separately, p.167) to start and stop the movie shooting if the drive mode is or . Set the shooting timing switch to <2> (2-sec. delay), then press the transmit button. If the switch is set to (immediate shooting), still photo shooting will take effect. With a fully-charged Battery Pack LP-E6, the total movie shooting time will be as follows: approx. 1 hr. 35 min. at room temperature (23°C/73°F), and approx. 1 hr.
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking Still Photos during Movie Shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx. 1 sec. The captured still photo will be recorded to the card, and the movie shooting will resume automatically when the Live View image is displayed. The movie and still photo will be recorded as separate files on the card.
k Shooting Movies AEB cannot be used. Even if an external Speedlite is used, it will not fire. Continuous still photo shooting is possible during movie shooting. However, the captured images will not be displayed on the screen. Depending on the still photo’s image-recording quality, number of shots during continuous shooting, card performance, etc., movie shooting may stop automatically. If you want to shoot still photos continuously during movie shooting, using a high-speed card is recommended.
Shooting Function Settings Q Quick Control In Creative Zone modes, you can set the following: AF method, drive mode, image-recording quality, movie-recording size, soundrecording level (with [Sound recording: Manual] set), white balance, Picture Style, Auto Lighting Optimizer, and video snapshot. In Basic Zone modes, only the functions in bold can be set. 1 Press the button. The settable functions will be displayed. 2Select a function and set it. Press the key to select a function.
3 Setting the Movie-Recording Size With [Z2: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9. B [1280x720] : High-Definition (HD) recording quality. The aspect ratio will be 16:9. C [640x480] : Standard-definition recording quality. The aspect ratio will be 4:3.
3 Setting the Movie-Recording Size Total Movie Recording Time and File Size Per Minute MovieRecording Size A 65 4 X Total Recording Time (approx.) 4 GB Card 8 GB Card 16 GB Card File Size (approx.) 16 min. 32 min. 1 hr. 4 min. 235 MB/min. 11 min. 22 min. 685 MB/min. 65 4 W 5 min. 87 B 87 C 65 X W X 18 min. 6 min. 48 min. 37 min. 1 hr. 14 min. 12 min. 25 min. 1 hr. 37 min. 3 hr. 14 min. 205 MB/min. 610 MB/min. 78 MB/min.
3 Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or a commercially-available stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [Z2: Sound recording]. Sound Recording/Sound-Recording Level [Auto] [Manual] : The sound-recording level is adjusted automatically. Auto level control will operate automatically in response to the sound level. : For advanced users.
3 Setting the Sound Recording Using the microphone The built-in microphone records monaural sound. Stereo sound recording is possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (φ3.5 mm) to the camera’s external microphone IN terminal (p.20). PY O C In Basic Zone modes, the settings available for [Sound recording] will be [On/Off].
3 Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing. Set the time code with [Z2: Time code]. Count Up [Rec run] [Free run] : The time code counts up only while you are shooting a movie. : The time code counts up whether you are shooting or not. PY O You can set the time code’s start C time.
3 Setting the Time Code Shooting still photos during movie shooting will cause a discrepancy between the actual time and time code. If [Free run] is set and you change the time, zone, or daylight saving time (p.36), the time code will be affected. The time code is not recorded for video snapshots. Regardless of the [Movie rec count] setting, the time code will always be recorded to the movie file. Movie Playback Count You can select what to display on the movie playback screen.
3 Setting the Time Code Drop Frame If the frame rate setting is 6 (29.97 fps) or 8 (59.94 fps), the time code’s frame count causes a discrepancy between the actual time and time code. This discrepancy can be corrected automatically. This correction function is called drop frame. [Enable] : The discrepancy is corrected automatically by skipping time code numbers. [Disable] : The discrepancy is not corrected. PY O C If the frame rate is 4 (23.
3 Menu Function Settings [Z1] Menu When the Live View shooting/Movie shooting switch is set to , the [Z1] and [Z2] tabs dedicated to movie shooting will be displayed. The menu options are as follows. AF method The AF methods are the same as described on pages 192-198. You can select [FlexiZoneAF (Single)], [u Live mode], or [Quick mode]. Note that continuous focusing of a moving subject is not possible.
3 Menu Function Settings [Z2] Menu Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you align the intersections over the subject for better balance in the composition. Movie recording size You can set the movie recording size (image size, frame rate, and compression method). For details, see page 216.
3 Shooting Video Snapshots You can easily create a short movie with the video snapshot function. A video snapshot is a short movie clip lasting approx. 2 sec., 4 sec., or 8 sec. A collection of video snapshots is called a video snapshot album and can be saved to the card as a single movie file. By changing the scene or angle in each video snapshot, you can create dynamic short movies. A video snapshot album can also be played together with background music (p.230, 254).
3 Shooting Video Snapshots [Album settings]. 3 Select Select [Album settings], then press <0>. If you want to continue shooting for an existing album, go to “Adding to Existing Album” (p.229). [Create a new album]. 4 Select Select [Create a new album], then press <0>. the snapshot length. 5 Select Press <0>, press the key to select the snapshot’s length, then Y pressP <0>. O C [OK]. 6 Select Select [OK], then press <0>.
3 Shooting Video Snapshots Creating a Video Snapshot Album the first video snapshot. 7 Shoot Press the <0> button, then shoot. The blue bar indicating the shooting duration will gradually decrease. After the set shooting duration elapses, the shooting stops automatically. After the LCD monitor turns off and the access lamp stops blinking, the confirmation screen will appear (p.228). as a video snapshot album. 8 Save Press the key to select [J Save as album], then press <0>.
3 Shooting Video Snapshots Options in Steps 8 and 9 Function Description J Save as album (Step 8) The movie clip will be saved as the video snapshot album’s first video snapshot. J Add to album (Step 9) The video snapshot just recorded will be added to the album recorded immediately before. W Save as a new album (Step 9) A new video snapshot album is created and the movie clip is saved as the first video snapshot. The new album will be a different file from the previously recorded album.
3 Shooting Video Snapshots Adding to Existing Album 1 Select [Add to existing album]. Follow step 4 on page 226 to select [Add to existing album], then press <0>. an existing album. 2 Select Turn the <5> dial to select an existing album, then press <0>. After confirming the dialog displayed, select [OK] on the screen, then press <0>. Certain video snapshot settings will change to match the existing album’s settings. Press the button to exit the menu and return to the movie shooting screen.
3 Shooting Video Snapshots Cautions for Shooting Video Snapshots You can add to an album only video snapshots with the same duration (approx. 2 sec., 4 sec., or 8 sec. each). Note that if you do any of the following while shooting video snapshots, a new album will be created for subsequent video snapshots. • Changing the [Movie rec. size] (p.216). • Changing the [Sound rec.] setting from [Auto/Manual] to [Disable] or from [Disable] to [Auto/Manual] (p.218). • Updating the firmware.
3 Shooting Video Snapshots Background Music Music recorded on the memory card must be used only for private enjoyment. Do not violate the rights of the copyright holder. You can play background music when you play back albums, normal movies, and slide shows on the camera (p.254, 257). To play background music, you must first copy the background music to the card using EOS Utility (provided software).
3 Shooting Video Snapshots the edited album. 3 Save Press the button to return to the Editing panel at the screen’s bottom. Press the key to select [W] (Save), then press <0>. The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite]. Then press <0>. PY O C If the card does not have enough free space, [New file] will not be available. When the battery level is low, editing albums is not possible.
Movie Shooting Cautions White and Red Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a white or red icon will appear. The white icon indicates that the image quality of still photos will deteriorate. You should stop still shooting and allow the camera’s internal temperature to cool before shooting again.
Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory). The slower the card, the faster the indicator will climb upward. If the indicator becomes full, movie shooting Indicator will stop automatically.
Image Playback This chapter explains how to play back and erase photos and movies, how to display them on a TV screen, and other playback-related functions. PY O C About images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or had their file names changed.
x Image Playback Single-Image Display 1 Play back the image. Press the button. The last captured image or last image viewed will appear. an image. 2 Select To play back images starting with the last image, turn the <5> dial counterclockwise. To play back images starting with the first captured image, turn the dial clockwise. Each time you press the button, the display format will change.
x Image Playback the image playback. 3 ExitPress the button to exit the image playback and return to shooting-ready state. 3 Grid Display On the single-image display, you can overlay a playback grid. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag n]. This function is convenient for checking the image’s vertical or horizontal tilt, as well as composition. PY O C The grid is not displayed during movie playback.
B: Shooting Information Display Sample Image Taken in a Creative Zone Mode AF Microadjustment Protect images Exposure compensation amount Flash exposure compensation amount Aperture Rating Folder number File number Histogram (Brightness/RGB) Shutter speed Picture Style/ Settings Metering mode Shooting mode White balance Image-recording quality Playback number/ Total images recorded Color temperature when
is set ISO speed Highlight tone priority PY O C Color space Shooting date and time White ba
B: Shooting Information Display Sample Image Taken in a Basic Zone Mode Ambience and ambience effects Shooting mode Lighting or scene * With images taken in a Basic Zone mode, the information displayed will differ depending on the shooting mode. * Photos taken in the mode will show [Background blur].
B: Shooting Information Display About the Highlight Alert When [33: Highlight alert] is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again. About the AF Point Display When [33: AF point disp.] is set to [Enable], the AF point that achieved focus will be displayed in red. If automatic AF point selection was used, multiple AF points may be displayed in red.
B: Shooting Information Display [RGB] Display This histogram is a graph showing the distribution of each primary color’s brightness level in the image (RGB or red, green, and blue). The horizontal axis indicates the color’s brightness level (darker on the left and brighter on the right), while the vertical axis indicates how many pixels exist for each color brightness level. The more pixels there are toward the left, the darker and less prominent the color.
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing four or nine images on one screen. 1 Press the button. Press the button during image playback. [6u] will be displayed on the lower right of the screen. to the index display. 2 Switch Turn the <6> dial counterclockwise. The 4-image index display will appear. The selected image is highlighted in a orange frame.
x Searching for Images Quickly I Jump through Images (Jump Display) With the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. 1 Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>. the jump method. 2 Select Turn the <5> dial to select the jump method, then press <0>.
u Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. 1 Magnified area position Magnify the image. The image can be magnified during image playback (single-image display), during image review after image capture, and from shooting-ready state. Press the button. The magnified view will appear. The magnified area and [6u] will be displayed on the lower right of the screen. The image magnification increases as you turn the <6> dial clockwise.
u Magnified View 3 Magnification Settings Under the [33] tab, when you select [Magnificatn (apx)], you can set the starting magnification and initial position for the magnified view. 1x (no magnification) The image will not be magnified. The magnified view will start with the single-image display. 2x, 4x, 8x, 10x (magnify from center) The magnified view will start at the image center at the selected magnification. Actual size (from selected point) The recorded image’s pixels will be displayed at approx.
b Rotating the Image You can rotate the displayed image to the desired orientation. 1 Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. an image. 2 Select Turn the <5> dial to select the image to be rotated. You can also select an image on the index display (p.242). the image. 3 Rotate Each time you press <0>, the PwillYrotate image clockwise as follows: O C90° 270° 0°. To rotate another image, repeat steps 2 and 3. To return to the menu, press the button.
3 Setting Ratings You can rate images and movies with one of five rating marks: l/m/ n/o/p. This function is called rating. 1 Select [Rating]. Under the [32] tab, select [Rating], then press <0>. an image or movie. 2 Select Turn the <5> dial to select the image or movie to be rated. If you press the button and turn the <6> dial counterclockwise, you can select an image or movie from a three-image display. To return to the single-image display, turn the <6> dial clockwise. PY O C the image or movie.
3 Setting Ratings The total number of images with a given rating that can be displayed is 999. If there are more than 999 images with a given rating, [###] will be displayed for that rating. Taking Advantage of Ratings With [32: Image jump w/6], you can display only images and movies with a specific rating. With [32: Slide show], you can play back only images and movies with a specific rating. With Digital Photo Professional (provided software, p.
Q Quick Control for Playback During playback, you can press the button to set any of the following: [J: Protect images, b: Rotate image, 9: Rating, R: RAW image processing (RAW images only), S: Resize (JPEG image only), : Highlight alert, : AF point display, e: Image jump w/ 6, k: Wi-Fi*]. For movies, only the functions in bold above can be set. * Not selectable if the [53] tab’s [Wi-Fi] is set to [Disable]. 1 Press the button. During image playback, press the button.
Q Quick Control for Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the button during the index display will switch to the single-image display and the Quick Control screen will appear. Pressing the button again will return to the index display.
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV set (p.261, 264) Use the provided AV cable or an HDMI Cable HTC-100 (sold separately) to connect the camera to a TV set. Then you can play back captured movies and still photos on the TV. If you have a High-Definition TV set and connect your camera with an HDMI cable, you can watch Full High-Definition (Full HD: 1920x1080) and HighDefinition (HD: 1280x720) movies with higher image quality.
k Enjoying Movies Playback and Editing with a Computer (p.392) The movie files recorded on the card can be transferred to a computer and played with ImageBrowser EX (provided software). To have the movie play back smoothly on a computer, use a highperformance computer. Regarding the computer hardware requirements for ImageBrowser EX, refer to the PDF file ImageBrowser EX User Guide.
k Playing Movies 1 Play back the image. Press the button to display images. a movie. 2 Select Turn the <5> dial to select the movie to be played. On the single-image display, the icon displayed on the upper left indicates a movie. If the movie is a video snapshot, < > will be displayed. You can press the button to switch to the shooting information display (p.238). In the index display, perforations at the left edge of a thumbnail indicate a movie.
k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. 8 Slow motion Adjust the slow motion speed by pressing the key. The slow-motion speed is indicated at the upper right of the screen. 5 First frame Displays the movie’s first frame. 3 Previous frame Each time you press <0>, the previous frame is displayed. If you hold down <0>, it will rewind the movie. 6 Next frame Each time you press <0>, the movie will play frame-byframe.
X Editing a Movie’s First and Last Scenes You can edit out the first and last scenes of a movie in 1-sec. increments. 1 On the movie playback screen, select [X]. The movie editing panel will be displayed at the bottom of the screen. the part to be edited out. 2 Specify Select either [U] (Cut beginning) or [V] (Cut end), then press <0>. Press (fast forward) or turn the <5> dial (frame-by-frame) to specify the position where you want to delete the scene.
X Editing a Movie’s First and Last Scenes the edited movie. 4 Save Select [W], then press <0>. The save screen will appear. To save it as a new movie, select [New file]. To save it and overwrite the original movie file, select [Overwrite]. Then press <0>. On the confirmation screen, select [OK], then press <0> to save the edited movie and return to the movie playback screen. PY O C Since the editing is performed in approx. 1-sec.
3 Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. 1 Number of images to be played Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. the images to be played. 2 Select Press the key to select the desired option, then press <0>. [All images/Movies/Stills] Press the key to select one of the following: [jAll images/ kMovies/zStills]. Then press <0>.
3 Slide Show (Auto Playback) Item Playback Description jAll images All the still photos and movies on the card will be played back. iDate Still photos and movies taken on the selected shooting date will be played back. nFolder Still photos and movies in the selected folder will be played back. kMovies Only the movies on the card will be played back. zStills Only the still photos on the card will be played back.
3 Slide Show (Auto Playback) [Transition effect] [Background music] the slide show. 4 StartPress the key to select [Start], then press <0>. After [Loading image...] is displayed, the slide show will start. slide show. 5 ExitTothe exit Ythe slide show and return to P the setting screen, press the CO button. To pause the slide show, press <0>. During pause, [G] will be displayed on the upper left of the image. Press <0> again to resume the slide show.
3 Slide Show (Auto Playback) Selecting the Background Music 1 Select [Background music]. Set [Background music] to [On], then press <0>. the background music. 2 Select Press the key to select the desired background music, then press <0>. You can also select multiple background music tracks. background music. 3 PlayTo the listen to a sample of the background music, press the PYbutton. O CPress the key to play another background music track.
Viewing the Images on TV You can view the still photos and movies on a TV set. Adjust the movie’s sound volume with the TV set. The sound volume cannot be adjusted with the camera. Before connecting or disconnecting the cable between the camera and TV set, turn off the camera and TV set. Depending on the TV set, part of the image displayed may be cut off. Viewing on High-Definition (HD) TV Sets (Connected with HDMI) HDMI Cable HTC-100 (sold separately) is required. 1 Connect the HDMI cable to the camera.
Viewing the Images on TV the button. 5 Press The image will appear on the TV screen. (Nothing will be displayed on the camera’s LCD monitor.) The images will automatically be displayed at the TV’s optimum resolution. By pressing the button, you can change the display format. To play back movies, see page 253. The images cannot be output at the same time from both the and terminals. Do not connect any other device’s output to the camera’s terminal. Doing so may cause a malfunction.
Viewing the Images on TV the camera to a TV set. 2 Connect Use an HDMI cable to connect the camera to the TV. The TV’s input will switch automatically to the HDMI port connected to the camera. the camera’s button. 3 Press An image will appear on the TV screen and you can use the TV’s remote control to play back images. an image. 4 Select Point the remote control toward the TV set and press the / select an image.
Viewing the Images on TV Viewing on Non-HD TV Sets (Connected with AV Cable) 1 Connect the provided AV cable to the camera. With the plug’s logo facing the back of the camera, insert it into the terminal. the AV cable to the TV 2 Connect set. (Red) (White) AUDIO (Yellow) VIDEO Connect the AV cable to the TV’s video IN terminal and audio IN terminal. on the TV and switch the 3 Turn TV’s video input to select the connected Yport. P O camera’s power switch to 4 Set Cthe <1>.
K Protecting Images Protecting an image prevents it from being erased accidentally. 3 Protecting a Single Image 1 Select [Protect images]. Under the [31] tab, select [Protect images], then press <0>. [Select images]. 2 Select Select [Select images], then press <0>. The images will be displayed. Image protect icon Y P O 3 C Turn the <5> dial to select the Protect the image. image to be protected, then press <0>. The image will be protected, and the icon will appear at the top of the screen.
K Protecting Images 3 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at one time. When you select [All images in folder] or [All images on card] in [x1: Protect images], all the images in the folder or on the card will be protected. To cancel the image protection, select [Unprotect all images in folder] or [Unprotect all images on card]. PY O C If you format the card (p.53), the protected images will also be erased. Movies can also be protected.
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images (p.265) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them. Erasing a RAW+JPEG image will erase both the RAW and JPEG images. Erasing a Single Image 1 Play back the image to be erased. the button.
L Erasing Images [Select and erase images]. 2 Select Select [Select and erase images], then press <0>. An image will be displayed. If you press the button and turn the <6> dial counterclockwise, you can select an image from a threeimage display. To return to the singleimage display, turn the <6> dial clockwise. the images to be erased. 3 Select Turn the <5> dial to select the image to be erased, then press <0>. A checkmark will be displayed on the upper left of the screen.
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. 1 Select [LCD brightness]. Under the [52] tab, select [LCD brightness], then press <0>. the brightness. 2 Adjust While referring to the gray chart, press the key, then press <0>. PY O C To check the image’s exposure, looking at the histogram is recommended (p.240).
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the computer instead of horizontally. You can change the setting for this feature. 1 Select [Auto rotate]. Under the [51] tab, select [Auto rotate], then press <0>. the auto rotation. 2 SetSelect the desired option, then press <0>.
Post-Processing Images You can process RAW images with the camera or resize (shrink) JPEG images. PY O C The M mark shown on the right of the page title indicates that the function is available only in Creative Zone modes (d/s/f/a/F). The camera may not be able to process images taken with another camera. Post-processing images as described in this chapter is not possible if the camera is set for multiple exposures, or while it is connected to a computer via the terminal.
R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. While the RAW image itself does not change, you can process the RAW image according to different conditions to create any number of JPEG images from it. Note that 41 and 61 images cannot be processed with the camera. Use Digital Photo Professional (provided software, p.392) to process those images. 1 Select [RAW image processing].
R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the setting screen. Turn the <5> dial to change the setting. To finalize the change and return to the screen in step 3, press <0>. the image. 4 Save Select [W] (Save), then press <0>. Select [OK] to save the image. Check the destination folder and image file number, then select [OK]. To process another image, repeat steps 2 to 4. To return to the menu, press the button.
R Processing RAW Images with the CameraN RAW Image-processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance (p.120) You can select the white balance. If you select [P], turn the <6> dial to set the color temperature on the setting screen. The displayed image will reflect the setting’s effect. Picture Style (p.112) You can select the Picture Style.
R Processing RAW Images with the CameraN Color space (p.140) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.131) If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, press the button to magnify the image and check the corners. (Press the button again to return to the normal view.
R Processing RAW Images with the CameraN Chromatic aberration correction When [Enable] is set, the lens’ chromatic aberrations (color fringing along the subject’s outline) can be corrected. If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, press the button to magnify the image. (Press the button again to return to the normal view.
S Resize You can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/4/a/b images. JPEG c and RAW images cannot be resized. 1 Select [Resize]. Under the [32] tab, select [Resize], then press <0>. The images will be displayed. an image. 2 Select Turn the <5> dial to select the image you want to resize. If you press the button and turn the <6> dial counterclockwise, you can select an image from the index display.
S Resize Resize Options According to Original Image Size Available Resize Settings Original Image Size 3 4 a b k k k k k k k 4 k a c k k b About Image Sizes The image size displayed in step 3 on the preceding page, such as [***M ****x****], has a 3:2 aspect ratio. The image size according to aspect ratios is shown in the table below. The asterisked image-recording quality figures do not exactly match the aspect ratio. The image will be cropped slightly.
Sensor Cleaning The camera has a Self Cleaning Sensor Unit to automatically shake off dust adhered to the image sensor’s front layer (low pass filter). The Dust Delete Data can also be appended to the image so that the dust spots remaining can be erased automatically by Digital Photo Professional (provided software, p.392).
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation. However, you can choose to perform sensor cleaning at any time, or disable it. Cleaning the Sensor Now 1 Select [Sensor cleaning]. Under the [54] tab, select [Sensor cleaning], then press <0>. [Clean nowf]. 2 Select Select [Clean nowf], then press <0>.
3 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later. The Dust Delete Data is used by Digital Photo Professional (provided software, p.392) to erase the dust spots automatically. Preparation Prepare a solid white object such as a sheet of paper. Set the lens focal length to 50 mm or longer.
3 Appending Dust Delete DataN a solid-white object. 3 Photograph At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. The picture will be taken in aperturepriority AE mode at an aperture of f/22. Since the image will not be saved, the data can still be obtained even if there is no card in the camera. When the picture is taken, the camera will start collecting the Dust Delete Data.
3 Manual Sensor CleaningN Dust that could not be removed by the automatic sensor cleaning can be removed manually with a blower, etc. Before cleaning the sensor, detach the lens from the camera. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. 1 Select [Sensor cleaning]. Under the [54] tab, select [Sensor cleaning], then press <0>. [Clean manually]. 2 Select Select [Clean manually], then press <0>.
3 Manual Sensor CleaningN While cleaning the sensor, never do any of the following. If the power is cut off, the shutter will close and the shutter curtains and image sensor may get damaged. • Setting the power switch to <2>. • Removing or inserting the battery. The surface of the image sensor is extremely delicate. Clean the sensor with care. Use a plain blower without any brush attached. A brush can scratch the sensor. Do not insert the blower tip inside the camera beyond the lens mount.
Printing Images Printing (p.288) You can connect the camera directly to a printer and print out the images on the card. The camera is compatible with “wPictBridge” which is the standard for direct printing. You can also use a wireless LAN to send images to a PictBridge (DPS over IP) printer and print them. For details, refer to the Wi-Fi Function Instruction Manual. PY O C Digital Print Order Format (DPOF) (p.
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor. Connecting the Camera to the Printer 1 Set the camera’s power switch to <2>. the printer. 2 SetForupdetails, refer to the printer’s instruction manual. the camera to the 3 Connect printer. Use theY P interface cable provided with theO camera. CConnect the cable to the camera’s terminal with the cable plug’s icon facing the front of the camera.
Preparing to Print wPictBridge back the image. 6 PlayPress the button. The image will appear, and the icon will appear on the upper left to indicate that the camera is connected to a printer. PY O C Movies cannot be printed. The camera cannot be used with printers compatible only with CP Direct or Bubble Jet Direct. Do not use any interface cable other than the one provided. If there is a long beeping sound in step 5, it indicates a problem with the printer.
w Printing The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon 1 Select the image to be printed. Check that the icon is displayed on the upper left of the LCD monitor. Turn the <5> dial to select the image to be printed. <0>. 2 Press The print setting screen will appear. Print setting screen Sets the printing effects (p.290).
w Printing Q Setting the Paper Size Select the size of the paper loaded in the printer, then press <0>. The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in the printer, then press <0>. The page layout screen will appear. U Setting the Page Layout Select the page layout, then press <0>. The print setting screen will reappear. PY O C Bordered The print will have white borders along the edges. Borderless The print will have no borders.
w Printing effects. 4 SetSettheit ifprinting necessary. If you do not need to set any printing effects, go to step 5. What is displayed on the screen differs depending on the printer. Select the option, then press <0>. Select the desired printing effect, then press <0>. If the icon is displayed brightly next to , you can also adjust the printing effect (p.292). Printing Effect Description EOn The image will be printed using the printer’s standard colors.
w Printing the date and file number 5 Set imprinting. Set them if necessary. Select , then press <0>. Set as desired, then press <0>. of copies. 6 SetSettheit ifnumber necessary. Select , then press <0>. Set the number of copies, then press <0>. printing. 7 StartSelect [Print], then press <0>. Y P O C The [Default] setting for printing effects and other options are the printer’s own default settings as set by the printer’s manufacturer.
w Printing e Adjustment of Printing Effects In step 4 on page 290, select the printing effect. When the icon is displayed brightly next to , you can press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4. Brightness The image brightness can be adjusted. Adjust levels When you select [Manual], you can change the histogram’s distribution and adjust the image’s brightness and contrast.
w Printing Trimming the Image Tilt correction You can crop the image and print only the trimmed portion as if the image was recomposed. Set the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again before printing. 1 On the print settings screen, select [Trimming]. 2 Set the trimming frame size, position, and aspect ratio. The image area within the trimming frame will be printed.
w Printing Depending on the printer, the trimmed image area may not be printed as you specified. The smaller you make the trimming frame, the grainier the picture will look in the print. While trimming the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the trimming frame may not be displayed accurately. Handling Printer Errors If you resolve a printer error (no ink, no paper, etc.
W Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options 1 Select [Print order]. Under the [31] tab, select [Print order], then press <0>. [Set up]. 2 Select Select [Set up], then press <0>. PY O C as desired. 3 SetSetthetheoption [Print type], [Date], and [File No.].
W Digital Print Order Format (DPOF) K Print type Date File number Standard Prints one image on one sheet. L Index Multiple thumbnail images are printed on one sheet. K L Both Prints both the standard and index prints. On Off On Off [On] imprints the recorded date on the print. [On] imprints the file number on the print. the setting. 4 ExitPress the button. The print order screen will reappear. Next, select [Sel.Image], [Byn], or [All image] to order the images to be printed.
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6> dial clockwise. Press the button to save the print order to the card. Quantity Total images selected Checkmark Index icon [Standard] [Both] Press and a print order for one copy of the displayed image will be placed.
W Direct Printing of Print-Ordered Images With a PictBridge printer, you can easily print images with DPOF. 1 Prepare to print. See page 286. Follow the “Connecting the Camera to the Printer” procedure up to step 5. 2 Under the [31] tab, select [Print order]. 3 Select [Print]. [Print] will be displayed only if the camera is connected to a printer and printing is possible. 4 Set the [Paper settings] (p.288)P .Y CO Set the printing effects (p.290) if necessary. 5 Select [OK].
p Specifying Images for a Photobook When you select images to use in photobooks (up to 998 images) and use EOS Utility (provided software) to transfer them to a computer, the selected images will be copied into a dedicated folder. This function is useful for ordering photobooks online and for printing photobooks on a printer. Specify One Image at a Time 1 Select [Photobook Set-up]. Under the [x1] tab, select [Photobook Set-up], then press <0>. [Select images].
p Specifying Images for a Photobook Specifying All Images in a Folder or on a Card You can specify all the images in a folder or on a card at one time. When [x1: Photobook Set-up] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be specified. To cancel the image specification, select [Clear all in folder] or [Clear all on card]. PY O C Do not specify images already specified for a photobook in another camera for another photobook with this camera.
Customizing the Camera You can customize various camera functions to suit your picture-taking preferences with Custom Functions. Also, the current camera settings can be saved under the Mode Dial’s and positions. The functions explained in this chapter work only in the Creative Zone modes.
3 Setting Custom FunctionsN 1 Select [8]. the group. 2 Select Select one of the C.Fn I-III, then press <0>. Custom Function number the Custom Function 3 Select number. Press the key to select the Custom Function number, then press <0>. the setting as desired. 4 Change Select the desired setting (number), then press <0>. Repeat steps 2 to 4 if you want to set another Custom Functions. At the bottom of the screen, the current Custom Function settings are indicated below the respective function numbers.
3 Custom FunctionsN A LV Shooting C.Fn I: Exposure 1 Exposure level increments 2 ISO speed setting increments 3 Bracketing auto cancel 4 Bracketing sequence 5 Number of bracketed shots 6 Safety shift p.304 p.305 p.306 2 2 2 2 2 2 k Movie Shooting 2 In a (Still photo, with WB bracketing) C.Fn II: Autofocus 1 Tracking sensitivity 2 Acceleration/deceleration tracking p.
3 Custom Function SettingsN C.Fn I: Exposure C.Fn I -1 Exposure level increments 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. This is effective when you prefer to control the exposure in less fine increments than 1/3-stop increments. With setting 1, the exposure level will be displayed in the viewfinder and on the LCD monitor as shown below. C.Fn I -2 0: 1/3-stop 1: 1-stop C.
3 Custom Function SettingsN C.Fn I -4 Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0: 0a-a+ 1: -a0a+ 2: +a0aWhite Balance Bracketing AEB B/A Direction 0 : Standard exposure M/G Direction 0 : Standard white balance 0 : Standard white balance - : Decreased exposure - : Biased toward blue - : Biased toward magenta + : Increased exposure + : Biased toward green C.
3 Custom Function SettingsN C.Fn I -6 Safety shift 0: Disable 1: Shutter speed/Aperture This takes effect in the shutter-priority AE (s) and aperture-priority AE (f) modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure. 2: ISO speed This works in the Program AE (d), shutter-priority AE (s), and aperturepriority AE (f) modes.
3 Custom Function SettingsN C.Fn II: Autofocus C.Fn II -1 Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. [0] Default setting suited for most subjects. Suited for normal, moving subjects. [Locked on: -2 / Locked on: -1] The camera will try to continue focusing the subject even if an obstacle enters the AF points or if the subject strays from the AF points.
3 Custom Function SettingsN C.Fn II -2 Acceleration/deceleration tracking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly, etc. [0] Suited for subjects that move at a fixed speed. [+2/+1] Effective for subjects having sudden movements, sudden acceleration/ deceleration, or sudden stops. Even if the moving subject’s speed suddenly changes dramatically, the camera continues to focus the target subject.
3 Custom Function SettingsN C.Fn II -4 AI Servo 2nd image priority You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF. [Equal priority] Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, shooting speed may slow down. [Shooting speed priority] ( ) Priority is given to the continuous shooting speed instead of achieving focus.
3 Custom Function SettingsN C.Fn II -6 Lens drive when AF impossible If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop searching. 0: Continue focus search 1: Stop focus search If autofocus starts and the focus is far off or if focus cannot be achieved, the lens drive stops. This prevents the lens from becoming grossly out of focus due to focus searching.
3 Custom Function SettingsN C.Fn II -9 AF Microadjustment Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. For details, see page 314. C.Fn III: Operation/Others C.Fn III -1 Dial direction during Tv/Av 0: Normal 1: Reverse direction The dial’s turning direction for setting the shutter speed and aperture can be reversed. In the shooting mode, the turning direction of the <6> and <5> dials will be reversed.
3 Custom Function SettingsN C.Fn III -2 Focusing screen If you change the focusing screen, change this setting to match the focusing screen so that correct exposures are obtained. 0: Eg-A II 1: Eg-D 2: Eg-S About focusing screen characteristics Eg-A II: Standard Precision Matte Standard focusing screen that comes with the camera. It provides both adequate viewfinder brightness and manual focusing ease. Eg-D : Precision Matte with Grid The focusing screen has grid lines.
3 Custom Function SettingsN C.Fn III -3 Multi function lock When the switch is set to the right, it will prevent the <6>, <5> dail, and <9> from accidentally changing a setting. Select the camera control you want to lock, then press <0> to append a checkmark and select [OK]. 6 Main Dial 5 Quick Control Dial 9 Multi-controller If the switch is set and you try to use one of the locked camera controls, will be displayed in the viewfinder and on the LCD panel.
8: AF Microadjustment Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. This is called “AF Microadjustment”. Before making the adjustment, read “Notes for AF Microadjustment” on page 319. Normally, this adjustment is not required. Do this adjustment only if necessary. Note that doing this adjustment may prevent correct focusing from being achieved.
8: AF Microadjustment the adjustment. 5 Make Press the key to make the adjustment. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus. Setting it toward “+: ” will shift the point of focus to the rear of the standard point of focus. After making the adjustment, press <0>. Select [1: All by same amount], then press <0>. Press the button to exit. Ythe result of the 6 Check P adjustment.
8: AF Microadjustment 2: Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment has been registered, the point of focus will always be shifted by the adjustment amount. Set the adjustment manually by adjusting, shooting, and checking the result. Repeat this until the desired adjustment is made.
8: AF Microadjustment Enter the serial number. Press the key to select the digit to be entered, then press <0> to display . Press the key to enter the number, then press <0>. After entering all the digits, select [OK] and press <0>. About the Lens Serial Number In step 3, if “ * ” appears in front of the 10-digit lens serial number, you cannot register several copies of the same lens model. Even if you enter the serial number, “ * ” will remain displayed.
8: AF Microadjustment Single focal length lens Zoom lens the adjustment. 4 Make For a zoom lens, press the key and select the wide-angle (W) or telephoto (T) end. Press <0> and the box will disappear, allowing you to make the adjustment. Press the key to adjust as desired, then press <0>. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus.
8: AF Microadjustment Clearing All AF Microadjustments When [ Clear all] appears at the bottom of the screen, pressing the button will clear all the adjustments made for [1: All by same amount] and [2: Adjust by lens]. PY O C Notes for AF Microadjustment The AF’s point of focus will vary slightly depending on the subject conditions, brightness, zoom position, and other shooting conditions. Therefore, even if you perform AF Microadjustment, focus may still not be achieved at the suitable position.
8: Custom Controls You can assign often-used functions to camera buttons or dials according to your preferences. 1 Select [C.Fn III: Operation/ Others]. Under the [8] tab, select [C.Fn III: Operation/Others], then press <0>. [5]:[Custom Controls]. 2 Select Select [5]:[Custom Controls], then press <0>. The Custom Controls screen will appear. a camera button or dial. 3 Select Select aY camera button or dial, then P<0>. press O CThe name of the camera control and the assignable functions will be displayed.
8: Custom Controls With the screen in step 3 displayed, you can press the button to cancel the Custom Control settings. Note that the [8C.Fn III -5: Custom Controls] settings will not be canceled even if you select [8: Clear all Custom Func. (C.Fn)].
8: Custom Controls Assignable Functions to Camera Controls Function Page Metering and AF start AF 2 AF stop 324 ONE SHOT z AI SERVO 2 2 2 2 2 2 2 2 2 2 2 2 2 2 AF point direct selection Metering start 324 AE lock/FE lock 2 AE lock AE lock (while button pressed) Exposure 2 AE lock (hold) FE lock 325 Set ISO speed (hold button, turn ) PY O C Shutter speed setting in M mode Aperture setting in M mode External flash Image Flash exposure compensation Image quality Picture Style
8: Custom Controls * 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 PY O C 2 2 2 2 2 2 2 2 2 2 2 * The AF stop button ( 2 ) is provided only on super telephoto IS lenses.
8: Custom Controls : Metering and AF start When you press the button assigned to this function, metering and AF are executed. : AF stop The AF will stop while you hold down the button assigned to this function. Convenient when you want to lock the focus during AI Servo AF. : ONE SHOT z AI SERVO You can switch the AF operation. In One-Shot AF mode, when you hold down the button to which this function is assigned, the camera switches to AI Servo AF mode.
8: Custom Controls : AE lock When you press the button assigned to this function, you can lock the exposure (AE lock) during the metering. Convenient when you want to focus and meter the shot at different areas or when you want to take multiple shots at the same exposure setting. : AE lock (while button pressed) The exposure will be locked (AE lock) while you press the shutter button. : AE lock (hold) When you press the button assigned to this function, you can lock the exposure (AE lock).
8: Custom Controls : Flash exposure compensation Press <0> to display the flash exposure compensation setting screen (p.170) on the LCD monitor. : Image quality Press <0> to display the image-recording quality setting screen (p.102) on the LCD monitor. : Picture Style Press <0> to display the Picture Style selection setting screen (p.112) on the LCD monitor. : Depth-of-field preview When you press the depth-of-field preview button, the aperture will stop down and you can check the depth of field (p.147).
3 Registering My MenuN Under the My Menu tab, you can register up to six menu options and Custom Functions whose settings you change frequently. Select [My Menu settings]. 1 Under the [9] tab, select [My Menu settings], then press <0>. [Register to My Menu]. 2 Select Select [Register to My Menu], then press <0>. the desired items. 3 Register Select the item, then press <0>. On the confirmation dialog, select [OK] and press <0> to register the item. You can register up to six items.
w Register Custom Shooting ModesN You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial’s and positions. 1 Select [Custom shooting mode (C1, C2)]. Under the [54] tab, select [Custom shooting mode (C1, C2)], then press <0>. [Register settings]. 2 Select Select [Register settings], then press <0>. the Custom shooting mode.
w Register Custom Shooting ModesN Settings Registered Shooting Settings Shooting mode + settings, ISO speed, exposure compensation, flash exposure compensation, AF operation, AF point, drive mode, and metering mode.
w Register Custom Shooting ModesN [C.Fn I: Exposure] Exposure level increments, ISO speed setting increments, Bracketing auto cancel, Bracketing sequence, Number of bracketed shots, Safety shift [C.Fn II: Autofocus] Tracking sensitivity, Acceleration/deceleration tracking, AI Servo 1st image priority, AI Servo 2nd image priority, AFassist beam firing, Lens drive when AF impossible, Orientation linked AF point, Superimposed display, AF Microadjustment [C.
Reference This chapter provides reference information for camera features, system accessories, etc. PY O C Certification Logo Under the [54] tab, if you select [Certification Logo Display] and press <0>, some of the logos of the camera’s certifications will appear. Other certification logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.
B Button Functions When you press the button while the camera is ready to shoot, you can display [Displays camera settings], [Electronic level] (p.60), and [Displays shooting functions] (p.333). Under the [53] tab, [z button display options] enables you to select the options displayed when the button is pressed. Select the desired display option and press <0> to append a checkmark . After making the selection, select [OK], then press <0>.
B Button Functions Shooting Function Settings White balance correction Shutter speed Shooting mode Aperture AE lock Flash exposure compensation ISO speed Highlight tone priority Exposure level indicator Picture Style Wi-Fi function Custom Controls AF operation Image-recording quality Quick Control icon Possible shots Battery check White balance AF point selection Eye-Fi card transmission status PY O C GPS acquisition status Logging function Drive mode Max.
3 Checking the Battery Information You can check the battery’s condition on the LCD monitor. Each Battery Pack LP-E6 has a unique serial number, and you can register multiple battery packs to the camera. When you use this feature, you can check the registered battery pack’s remaining capacity and operation history. Select [Battery info.]. Under the [54] tab, select [Battery info.], then press <0>. The battery info screen will appear. Battery position Battery model or household power source being used.
3 Checking the Battery Information Registering the Battery to the Camera You can register up to six LP-E6 battery packs to the camera. To register multiple battery packs to the camera, do the procedure below for each battery pack. 1 Press the button. With the battery info. screen displayed, press the button. The battery history screen will appear. If the battery has not been registered, it will be grayed out. [Register]. 2 Select Select [Register], then press <0>.
3 Checking the Battery Information Labeling the Serial Number on the Battery It is convenient to label all registered Battery Pack LP-E6 with their serial numbers, using commercially available labels. Serial number 1 Write the serial number on a label. Write the serial number displayed on the battery history screen on a label approx. 25 mm x 15 mm / 1.0 in. x 0.6 in. in size. 7c40 0300 out the battery and affix the 2 Take label. Set the power switch to <2>.
3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery Pack You can check the remaining capacity of any battery pack (even when not installed) and also when it was last used. Serial number Date last used Look for the serial number. Refer to the battery’s serial number label and look for the battery’s serial number on the battery history screen. You can check the respective battery pack’s remaining capacity and the date when it was last used.
Using a Household Power Outlet With AC Adapter Kit ACK-E6 (sold separately), you can connect the camera to a household power outlet and not worry about the remaining battery level. 1 Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the AC Adapter’s socket. the power cord. 2 Connect Connect the power cord as shown in the illustration. After using the camera, unplug the power plug from the power outlet. the cord in the groove.
Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card manufacturer.
Using Eye-Fi Cards the connection 4 Display information. Select [Connection info.], then press <0>. the [Access point SSID:]. 5 Check Check that an access point is displayed for [Access point SSID:]. You can also check the Eye-Fi card’s MAC address and firmware version. Press the button to exit the menu. picture. 6 TakeThethepicture Y is transferred and the P icon switches from gray (not O to one of the icons below.
Using Eye-Fi Cards Cautions for Using Eye-Fi Cards If [53: Wi-Fi] is set to [Enable], image transfer with an Eye-Fi card is not possible. If “ ” is displayed, an error occurred while retrieving the card information. Turn the camera’s power switch off and on again. Even if [Eye-Fi trans.] is set to [Disable], it may still transmit a signal. In hospitals, airports, and other places where wireless transmissions are prohibited, remove the Eye-Fi card from the camera.
Function Availability Table According to Shooting Mode For Still Photo Shooting o: Set automatically k: User selectable : Not selectable/Disabled Basic Zone Function All image quality settings selectable Automatically set/ ISO Auto ISO speed Manual Picture Style Creative Zone 8 2 3 4 5 6 F o o o o o o o o o o o o o o o o o Preset Custom Color temperature setting Correction/Bracketing Auto Lighting Optimizer G d sf a F k k k k k k k k*1 k*1 k k k k k Automatically set/Auto o o o o o o o Manual s
Function Availability Table According to Shooting Mode Basic Zone Function A C Creative Zone 8 2 3 4 5 6 F G d sf a F Evaluative metering o o o o o o o o o k k k k k Metering Metering mode mode k k k k k selection Program shift k AE lock k k k Exposure Exposure compensation k k k k k k k AEB Depth-of-field preview Single shooting Drive External flash k k k k k k k k k k k k k k k k k k k Continuous shooting k Silent single k shooting Silent continuous k shooting 10-sec.
Function Availability Table According to Shooting Mode For Movie Shooting o: Set automatically k: User selectable : Not selectable/Disabled Movie Function A C 8 d y All image quality settings selection (movie) Still Photos s f F k z*1 a M y k M k k k k k k k k All image quality settings selection (still photos) k k k Video snapshot k k k k k k k k o o o o o o o k Manual k Picture Automatically set/Auto o o o k k k k k Style Manual selection k k k k k Auto o o o k k k k k Preset k k k k k Cust
Function Availability Table According to Shooting Mode Movie Function A C 8 d y FlexiZone - Singled AF Live mode c Quick mode*3 f Manual focusing (MF) Metering mode k k k k o k k k k o Still Photos s f F k k k k k o k k k k o k k k k o k k k k o z*1 a M y k M k k k k o k k k k o k k k k k k k k *4 k k k k o k k k k o k k k k o Program shift AE lock Exposure Exposure compensation k k AEB Depth-of-field preview Single shooting Continuous shooting Silent single shooting Drive Silent
Menu Settings For Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Image quality Page 1*/41*/61* 73/83/74/84/7a/8a/b/c 102 Beep Enable / Disable - Release shutter without card Enable / Disable 32 Image review Off / 2 sec. / 4 sec. / 8 sec. / Hold 55 * Not selectable in or mode.
Menu Settings z: Shooting 3 (Red) Page Exposure compensation/AEB 1/3-stop increments, ±5 stops (AEB ±3 stops) 151 152 ISO speed settings ISO speed / ISO speed range / Auto ISO range / Minimum shutter speed 106 to 111 Auto Lighting Optimizer White balance Disable / Low / Standard / High OFF with M or Bulb Q/W/E/R/Y/U/D/O/ P (Approx.
Menu Settings A1: Live View shooting 1 (Red) Page Live View Shooting Enable / Disable AF method FlexiZone- Single / u Live mode / Quick mode 192 187 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n 187 Aspect ratio 3:2 / 4:3 / 16:9 / 1:1 188 Exposure simulation Enable / During e / Disable 189 A2: Live View shooting 2 (Red) Silent LV shooting Mode 1 / Mode 2 / Disable Metering timer 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 30 min.
Menu Settings 3: Playback 2 (Blue) Page Resize Downsize the image’s pixel count 277 Rating [OFF] / l / m / n / o / p 247 Slide show Playback description / Display time / Repeat / Transition effect / Background music 257 Image jump w/6 1 image / 10 images / 100 images / Date / Folder / Movies / Stills / Rating 243 Highlight alert Disable / Enable 240 AF point display Disable / Enable 240 Playback grid Off / 3x3 l / 6x4 m / 3x3+diag n 237 Histogram display Brightness / RGB 240 Movie
Menu Settings 5: Set-up 1 (Yellow) Page Select folder Create and select a folder 134 File number Continuous / Auto reset / Manual reset 136 Auto rotate OnzD / OnD / Off 270 Format card Initialize and erase data on the card 53 Eye-Fi settings Displayed when a commercially-available EyeFi card is inserted 339 Auto power off 1 min. / 2 min. / 4 min. / 8 min. / 15 min. / 30 min.
Menu Settings 5: Set-up 3 (Yellow) Page Video system NTSC / PAL 216 264 Feature guide Enable / Disable 63 z button display options Displays camera settings / Electronic level / Displays shooting functions 332 Wi-Fi Disable / Enable Wi-Fi function Transfer images between cameras / Connect to smartphone / Remote control (EOS Utility) / Print from Wi-Fi printer / Upload to Web service / View images on DLNA devices * * For details, refer to the Wi-Fi Function Instruction Manual on the CD-ROM.
Menu Settings 8: Custom Functions (Orange) C.Fn I: Exposure C.Fn II: Autofocus 304 Customize camera functions as desired C.Fn III: Operation/ Others Clear all Custom Functions (C.
Menu Settings For Movie Shooting Z1: Movie1 (Red) Page AF method FlexiZone- Single / u Live mode / Quick mode 223 Silent LV shooting Mode 1 / Mode 2 / Disable 223 Metering timer 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 30 min.
System Map ST-E2 ST-E3-RT 270EX II 90EX Eyepiece Extender EP-EX15 320EX 430EX II 600EX-RT/ Macro Ring Lite Macro Twin Lite MR-14EX MT-24EX 600EX Bundled Accessories Focusing screen Eg-A II Rubber Frame Eb E-series Dioptric Adjustment Lenses Wide Strap EW-EOS6D PY O C Battery Pack LP-E6 Eyecup Eb Battery Charger LC-E6 or LC-E6E AC Adapter DC Coupler AC-E6 DR-E6 Angle Finder C Focusing screen Eg-D Eg-S AC Adapter Kit ACK-E6 Battery Grip BG-E13 Car Battery Cable CB-570 Car Battery Charger CBC-
System Map GPS Receiver GP-E2 Remote Controller RC-6 Timer Remote Remote Switch Controller RS-80N3 TC-80N3 Wireless Controller LC-5 External microphone EF lenses HDMI Cable HTC-100 (2.9 m/9.5 ft.) Stereo AV Cable AVC-DC400ST (1.3 m/4.3 ft.) EOS DIGITAL Solution Disk Camera Instruction Manual PY O C TV/Video Software Instruction Manual PictBridge-compatible printer Interface Cable IFC-200U (1.9 m/6.2 ft.) Interface Cable IFC-500U (4.7 m/15.4 ft.
Troubleshooting Guide If a problem occurs with the camera, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. Power-Related Problems The battery pack does not recharge. If the battery’s remaining capacity (p.334) is 94% or higher, the battery will not be recharged. Do not recharge any battery pack other than genuine Canon Battery Pack LP-E6. The charger’s lamp blinks at high speed.
Troubleshooting Guide The access lamp still blinks even when the power switch is set to <2>. If the power is turned off while an image is being recorded to the card, the access lamp will remain on/continue to blink for a few seconds. When the image recording is completed, the power will turn off automatically. The battery becomes exhausted quickly. Use a fully-charged battery pack (p.28). The battery performance may have degraded. See [54: Battery info.
Troubleshooting Guide Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-S and EF-M lenses (p.39). No images can be shot or recorded. Make sure the card is properly inserted (p.31). Slide the card’s write-protect switch to the write/erase position (p.31). If the card is full, replace the card or delete unnecessary images to make space (p.31, 267).
Troubleshooting Guide The image is out of focus. Set the lens focus mode switch to (p.39). To prevent camera shake, press the shutter button gently (p.43, 44). If the lens has an Image Stabilizer, set the IS switch to <1> (p.42). In low light, the shutter speed may become slow. Use a faster shutter speed (p.144), set a higher ISO speed (p.106), use flash (p.170), or use a tripod. I cannot lock the focus and recompose the shot. Set the AF operation to One-Shot AF.
Troubleshooting Guide ISO 100 cannot be set. ISO speed expansion cannot be selected. If [z4: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200-25600 (or up to ISO 12800 for movie shooting). Even if you expand the settable ISO speed range in [ISO speed range], you cannot set expanded ISO speeds (L, H, H1, H2). When [z4: Highlight tone priority] is set to [Disable], ISO 100/125/160 can be set (p.130). The Auto Lighting Optimizer cannot be set.
Troubleshooting Guide The flash does not fire. If you use a non-Canon flash unit with Live View shooting, set [A2: Silent LV shoot.] to [Disable] (p.190). The flash always fires at full output. If you use a flash unit other than an EX-series Speedlite, the flash will always be fired at full output (p.171). When the [Flash metering mode] flash Custom Function is set to [TTL ] (autoflash), the flash will always be fired at full output (p.177). Flash exposure compensation cannot be set.
Troubleshooting Guide I cannot shoot a movie. Under the [53] tab, if you set [Wi-Fi] to [Enable], you cannot shoot movies. Before shooting movies, set [Wi-Fi] to [Disable]. Movie shooting stops by itself. If the card’s writing speed is slow, movie shooting may stop automatically. If the compression method is set to [IPB], use a card with a reading/writing speed of at least 6 MB per sec.
Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie when [Maximum: 25600] is set with [ISO speed range] and ISO speed is set to ISO 16000/20000/25600, the ISO speed will switch to ISO 12800 (during movie shooting with manual exposure). Even if you switch back to still photo shooting, the ISO speed will not revert to the original setting. If you shoot a movie when 1. L (ISO 50) or 2.
Troubleshooting Guide When I shoot still photos during movie shooting, the movie shooting stops. Setting a lower image quality for still photos and shooting fewer continuous still photos may resolve the problem. Time code is off. Shooting still photos during movie shooting will cause a discrepancy between the actual time and time code. When you want to edit a movie using time code, it is recommended not to shoot still photos during movie shooting. Wi-Fi Wi-Fi cannot be set.
Troubleshooting Guide Display Problems The menu screen shows few tabs and options. In Basic Zone modes, certain tabs and menu options are not displayed. Set a Creative Zone mode (p.51). The file name’s first character is an underscore (“_”). Set the color space to sRGB. If Adobe RGB is set, the first character will be an underscore (p.140). The file numbering does not start from 0001. If the card already contains recorded images, the image number may not start from 0001 (p.136).
Troubleshooting Guide The LCD monitor does not display a clear image. If the LCD monitor is dirty, use a soft cloth to clean it. In low or high temperatures, the LCD monitor display may seem slow or may look black. It will return to normal at room temperature. [Eye-Fi settings] does not appear. [Eye-Fi settings] will appear only when an Eye-Fi card is inserted in the camera.
Troubleshooting Guide When the movie is played back, camera operation noise can be heard. If you operate the camera’s dials or lens during movie shooting, the operation noise will also be recorded. Using an external microphone (commercially available) is recommended (p.219). The movie has still moments. During autoexposure movie shooting, if there is a drastic change in the exposure level, the recording will stop momentarily until the brightness stabilizes. If this happens, shoot with shooting mode (p.
Troubleshooting Guide I cannot resize the image. c JPEG images and 1/41/61 images cannot be resized with the camera (p.277). Sensor Cleaning Problems The shutter makes a noise during sensor cleaning. If you selected [Clean nowf], the shutter will make a noise, but no picture is taken (p.280). Automatic sensor cleaning does not work. If you repeatedly turn the power switch <1> / <2> at a short interval, the icon may not be displayed (p.34).
Troubleshooting Guide Image Transfer Problems I cannot transfer images to a computer. Install the provided software (EOS DIGITAL Solution Disk CDROM) on the computer (p.392). Check that EOS Utility’s top screen is displayed. Under the [53] tab, if [Wi-Fi] is set to [Enable], the camera cannot connect to a computer. Set [Wi-Fi] to [Disable], then connect the camera to the computer with an interface cable.
Error Codes Error number If there is a problem with the camera, an error message will appear. Follow the onscreen instructions. Countermeasures Number 01 02 Error Message and Solution Communications between the camera and lens is faulty. Clean the lens contacts. ÎClean the electrical contacts on the camera and lens or use a Canon lens (p.17, 20). PY O C Card cannot be accessed. Reinsert/change card or format card with camera. ÎRemove and insert the card again, replace the card, or format the card (p.
Specifications • Type Type: Recording media: Digital, single-lens reflex, AF/AE camera SD memory card, SDHC memory card*, SDXC memory card* Image sensor size: Compatible lenses: Approx. 35.8 x 23.
Specifications Noise reduction: Automatic image brightness correction: Highlight tone priority: Lens aberration correction: Applicable to long exposures and high ISO speed shots Auto Lighting Optimizer Provided Peripheral illumination correction, Chromatic aberration correction • Viewfinder Type: Coverage: Eye-level pentaprism Vertical/Horizontal approx. 97% (with Eye point approx. 21 mm) Magnification: Approx. 0.71x (-1 m-1 with 50 mm lens at infinity) Eye point: Approx.
Specifications • Exposure Control Metering modes: 63-zone TTL full-aperture metering • Evaluative metering (linked to all AF points) • Partial metering (approx. 8.0% of viewfinder at center) • Spot metering (approx. 3.5% of viewfinder at center) • Center-weighted average metering Metering range: EV 1 - 20 (at room temperature with EF50mm f/1.
Specifications • Shutter Type: Shutter speeds: Electronically-controlled, focal-plane shutter 1/4000 sec. to 30 sec., bulb, X-sync at 1/180 sec. • Drive System Drive modes: Continuous shooting speed: Max. burst: • External Speedlite Compatible Speedlites: Flash metering: Flash exposure compensation: FE lock: PC terminal: External Speedlite control: Single shooting, Continuous shooting, Silent single shooting, Silent continuous shooting, 10-sec. self-timer/ remote control, 2-sec.
Specifications Metering modes: Metering range: Silent shooting: Grid display: Evaluative metering (315 zones), Partial metering (approx. 11% of Live View screen), Spot metering (approx. 3% of Live View screen), Center-weighted average metering EV 0 - 20 (at room temperature with EF50mm f/1.4 USM lens, ISO 100) Provided (Mode 1 and 2) Three types • Movie Shooting Recording format: Movie Audio Recording size and frame rate: MOV MPEG-4 AVC / H.
Specifications ISO speed: (Recommended exposure index) Time code: Drop frames: Video snapshots: Sound recording: Grid display: Still photo shooting: • LCD Monitor Type: Monitor size and dots: Brightness adjustment: Electronic level: Interface languages: Feature guide / Help: With autoexposure: Auto ISO (automatically set within ISO 100 - ISO 12800), Maximum and minimum ISO speeds can be changed in Creative Zone modes With manual exposure: Auto ISO (automatically set within ISO 100 - ISO 12800), ISO 100
Specifications Slide show: Background music: Image protect: All images, by date, by folder, by movies, by stills, or by rating Selectable for slide shows and movie playback Possible • Post-Processing of Images In-camera RAW image processing: Brightness correction, White balance, Picture Style, Auto Lighting Optimizer, High ISO speed noise reduction, JPEG image-recording quality, Color space, Peripheral illumination correction, Distortion correction, and Chromatic aberration correction Resize: Possible •
Specifications • Power Battery: Battery information: Number of possible shots: (Based on CIPA testing standards) Movie shooting time: Battery Pack LP-E6 (Quantity 1) * AC power can be supplied via AC Adapter Kit ACK-E6. * With Battery Grip BG-E13 attached, size-AA/LR6 batteries can be used. Remaining capacity, Shutter count, Recharge performance, and Battery registration possible With viewfinder shooting: Approx. 1090 shots at room temperature (23°C/73°F), approx.
Specifications Working humidity: 85% or less Dimensions (W x H x D):Approx. 69.0 x 33.0 x 93.0 mm / 2.7 x 1.3 x 3.7 in. Weight: Approx. 130 g / 4.6 oz. • Battery Charger LC-E6E Compatible battery: Power cord length: Recharging time: Rated input: Rated output: Working temperature range: Working humidity: Dimensions (W x H x D): Weight: Battery Pack LP-E6 Approx. 1 m / 3.3 ft. Approx. 2 hr. 30 min. 100 - 240 V AC (50/60 Hz) 8.4 V DC/1.2 A 5°C - 40°C / 41°F - 104°F 85% or less Approx. 69.0 x 33.0 x 93.
Trademarks Adobe is a trademark of Adobe Systems Incorporated. Windows is a trademark or registered trademark of Microsoft Corporation in the United States and other countries. Macintosh and Mac OS are trademarks or registered trademarks of Apple Inc. in the United States and other countries. SDXC logo is a trademark of SD-3C, LLC. HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Use of genuine Canon accessories is recommended This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet. Do not use any home-made or modified batteries. - Do not short-circuit, disassemble, or modify the battery pack or back-up battery.
• If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. • Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. • Keep the camera from the reach of small children. The neck strap can accidentally choke the child.
Digital Camera Model DS126401 / DS126402 / DS126403 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS — This manual contains important safety and operating instructions for Battery Charger LC-E6 & LC-E6E. 2. Before using the charger, read all instructions and cautionary remarks on (1) the charger, (2) the battery pack, and (3) the product using the battery pack. 3. CAUTION — To reduce risk of injury, charge only the Battery Pack LP-E6. Other types of batteries may burst, causing personal injury and other damage. 4.
MEMO PY O C 386
Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer This chapter explains how to install the Camera Instruction Manual (on the CD-ROM provided) to your computer, download images from the camera to your computer, gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on your computer. It also explains how to view the PDF files on the Software Instruction Manual CD-ROM.
Viewing the Camera Instruction Manual CD-ROM The Camera Instruction Manual CD-ROM contains the following electronic manuals (PDF): Camera Instruction Manual Explains all the camera functions and procedures, including basic content. Wi-Fi Function Instruction Manual Explains all the Wi-Fi functions and procedures, including basic content. Viewing the Camera Instruction Manual on the CD-ROM To view the instruction manuals (PDF files), Adobe Reader 6.0 or higher must be installed in your computer.
Viewing the Camera Instruction Manual CD-ROM the START file. 3 Double-click The screen shown in step 4 will appear. The icon displayed will differ depending on your computer’s operating system. on the manual you want to view. 4 Click Click on the name of the manual under your respective language. PY O C The instruction manual in your language will be displayed. You can save the PDF file to your computer. All the instruction manuals (PDF files) have page links to make it quick to find the desired page.
Downloading Images to a Computer You can use the provided software to download the images in the camera to your computer. There are two ways to do this. Download by Connecting the Camera to the Computer 1 Install the software (p.394). the provided interface cable 2 Use to connect the camera to your computer. Use the interface cable provided with the camera. Connect the cable to the camera’s terminal with the cable plug’s icon facing the front of the camera.
Downloading Images to a Computer Downloading Images with a Card Reader If you have a commercially-available card reader, you can use it to download images to your computer. Install the software (p.394). 1 the card into the card 2 Insert reader. Y software to download 3 Use PCanon the images/movies. O C Use Digital Photo Professional. Use ImageBrowser EX. For details, refer to the Software Instruction Manual on the CD-ROM (p.395).
About the Software EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely with the computer connected to the camera. Also, you can copy background music tracks, such as EOS Sample Music*, to the card.
About the Software Picture Style Editor You can edit Picture Styles and create and save original Picture Style files. This software is aimed at advanced users who are experienced in processing images. Map Utility With the GPS position information, you can display where the picture was taken on a map on your computer. To install Map Utility, an Internet connection is required. Access the Internet, insert EOS DIGITAL Solution Disk into your computer, then click [Easy Installation] ([Install] for Macintosh).
Installing the Software Do not connect the camera to your computer before you install the software. The software will not be installed correctly. Even if your computer already has ImageBrowser EX installed, install ImageBrowser EX included on the CD-ROM that came with this camera. It is the latest version with features optimized for your camera. You can also use the auto update feature to add the latest functions.
Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Instruction Manual PDFs 1 Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. 2 Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. 3 Copy the [English] folder to your computer. Instruction Manual PDFs with the names below are copied. EOS Utility Digital Photo Professional PY O C Windows Macintosh EUx.
Index Numerics Audio/video output ............... 251, 261 10-sec. or 2-sec. delay .................100 Auto Lighting Optimizer................ 125 11-point AF auto selection ..............94 Auto playback............................... 257 1280x720 ......................................216 Auto power off .......................... 34, 55 1920x1080 ....................................216 Auto reset..................................... 137 4- or 9-image index display...........242 Auto rotate.....
Index Center-weighted average metering ........................................150 Charger .....................................26, 28 Chromatic aberration correction....132 Cleaning........................................279 Clear camera settings .....................56 Close-ups........................................77 Color space...................................140 Color temperature .................120, 122 Color tone .....................................116 Continuous file numbering ............
Index Flash-sync speed .............171, 173 Manual flash .............................174 Shutter synchronization (1st/2nd curtain) .......................175 Wireless....................................175 Flash exposure compensation .......................170, 176 Household power ......................... 338 Flash mode ...................................174 Image-recording quality................ 102 Flash-sync contacts ........................20 Focus confirmation light..................
Index L M Landscapes.....................................76 M (manual exposure) ........... 148, 208 Language ........................................38 Macro photography ........................ 77 Large (image-recording quality) ....103 Magnification ................................ 245 LCD monitor....................................17 Brightness adjustment ..............269 Electronic level ...........................60 Image playback ........................235 Menu screen......................
Index Editing out first and last scenes ......................................255 Enjoying....................................251 External microphone ................219 File size ....................................217 Frame rate................................216 Grid display ..............................224 Information display ...................210 Manual exposure shooting .......208 Metering timer ..........................223 Microphone.......................204, 219 Movie-recording size ...........
Index Protect (image erase protection)...265 Q Q (Quick Control)..49, 83, 185, 215, 249 Quick Control Dial ...........................46 Quick mode...................................197 R Rating mark...................................247 RAW......................................102, 104 RAW image processing ................272 RAW+JPEG ..................................102 Recharging......................................28 Recording level .............................218 Reduced display .................
Index Spot metering................................150 S-RAW (Small RAW) ....................104 Wi-Fi............................................. 351 Wind filter ..................................... 218 sRGB ............................................140 Stopped-down aperture ................147 Strap ...............................................27 System map..................................354 T Temperature warning ............201, 233 Time code .....................................
MEMO PY O C 403
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. http://www.usa.canon.com/eos http://www.usa.canon.com/support For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.