User's Manual

ManualsBrandsCanon ManualsElectronicsFM33490

1/1

Legal Notices

FCC (Federal Communications Commission)

Note: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules, and the limits for an ISM equipment, pursuant to

Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate, radio frequency energy and, if not installed and

used in accordance with the Operator's Manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

Use of shielded cables are required to comply with Class A limits in Subpart B of Part 15 of the

FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the

manual. If you make such changes or modifications, you could be required to stop operation of

the equipment.

If your equipment malfunctions, please contact your local authorized Canon dealer from whom

you purchased the equipment (if under warranty), or with whom you have a servicing contract. If

you are not sure who to contact, and have both purchased and are using the equipment in the

U.S.A., please refer to the "SUPPORT" page on Canon U.S.A.'s Web site

(http://www.usa.canon.com).

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of this device.

This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled

equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C

to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment

should be installed and operated with at least 20cm and more between the radiator and

person’s body (excluding extremities: hands, wrists, feet and ankles).

Summary of content (12 pages)

PAGE 1
Legal Notices FCC (Federal Communications Commission) Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules, and the limits for an ISM equipment, pursuant to Part 18 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 2
Wireless LAN Board NB-W1 User's Guide Please read this guide before operating this product. After you finish reading this guide, store it in a safe place for future reference.
PAGE 3
Users in the European Union and other European countries WEEE Directive European Union (and EEA) only. This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE).
PAGE 4
Preface Thank you for purchasing a Canon product. The Wireless LAN Board NB-W1 is a product that enables you to wirelessly connect your Canon MFP (Color imageRUNNER/imageRUNNER/imagePRESS series) to a network. This document describes the procedure for connecting a machine that includes the Wireless LAN Board NB-W1 to a network. Please read this manual thoroughly before operating the product to familiarize yourself with its capabilities, and to make the most of its many functions.
PAGE 5
Keys and Buttons Used in This Manual The following symbols and key/button names are a few examples of how keys and buttons to be clicked or pressed are expressed in this manual: • Control Panel Keys: Examples: Key Icon (Key Name) (Start) (Stop) • Touch Panel Display Keys: Examples: [Key Name] [Cancel] [Done] • Buttons on Computer Operation Screens: [Button Name] Examples: [OK] [Add] Displays Used in This Manual Screen shots of the touch panel display used in this manual have been taken from the
PAGE 6
Before You Start 1 CHAPTER This chapter describes what you need to know before you start using the product, including the system requirements, and the procedure for setting a primary network. Confirming the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Parts and Their Functions. . . . . . . . . . . . . . . . . . . .
PAGE 7
1 The NB-W1 can be used in either of the following network environments that have an access point. Before You Start Confirming the Network NOTE The NB-W1 normally communicates with the Infrastructure Mode, which works via an access point. Only when a firmware update has been performed unsuccessfully, does the NB-W1 communicate using the Adhoc Mode, which is its emergency startup mode. For information on the Adhoc Mode, see "Emergency Startup Mode (Adhoc Mode)," on p. 4-13.
PAGE 8
■ Environment where a computer and access point are connected with a LAN cable and the access point and the NB-W1 communicate wirelessly Hub 1 Before You Start Access Point Confirming the Network 1-3
PAGE 9
1 This section describes the system requirements of the NB-W1, including the types of access points and authentication servers it supports. Before You Start System Requirements IMPORTANT For information on the wireless LAN devices that can communicate with the NB-W1, see the Canon Web site (http://www.usa.canon.com/ for the U.S.A., http:// www.canon-europe.com/ for the UK, or http://www.canon.com/ for other countries/ regions).
PAGE 10
■ Authentication Server • RADIUS server - Microsoft IAS (Internet Authentication Server) based on Microsoft Windows Server 2003 - Cisco Secure ACS (Access Control Server) Version 3.1 or later ■ Certificate Authority • Microsoft Windows Server 2003 CA System Requirements 1-5 1 Before You Start NOTE • The RADIUS server supports EAP-TLS (Extensible Authentication Protocol-Transport Level Security), PEAP (Protected EAP), or EAP-TTLS (EAP-Tunneled TLS) authentication.
PAGE 11
Parts and Their Functions This section describes the various parts and their functions. Before You Start 1 LED Indicators If problems occur when communicating with the NB-W1, check the LED indicators on the side of the machine. For details on errors, see Chapter 3, "Troubleshooting." a b c a ERR1 Indicator (Yellow) Flashes when a problem occurs with security settings or an error occurs during authentication. b ERR2 Indicator (Orange) Flashes when a problem occurs with the NB-W1 hardware.
PAGE 12
NB-W1 External Antenna Before You Start 1 a a Make sure to use the external antenna included with this product. When experiencing difficulty communicating, adjust the position of this antenna.