User Manual

ManualsBrandsCanon ManualsElectronicsWireless LAN Module

1-1

Wireless LAN Board-C1

Check of bundled parts

Installation procedure

[1] Wireless board x 1 [2] Flat cable x 1

[3] Screw (TP;M3x6)  1

If bundled parts are used;

If the parts bundled with this product are used, the symbol indicating the use of

bundled parts is illustrated.

Bundled

parts

In this procedure manual, the frequent operations are illustrated with symbols.

Screw Connector Binding wire

Attach Detach Attach Detach Attach Detach

Claw

Attach Detach Push Plug in Switch ON

Check Visual check Noise check

Summary of content (7 pages)

PAGE 1
-1 Wireless LAN Board-C1 Check of bundled parts Installation procedure [1] Wireless board x 1 [2] Flat cable x 1 [3] Screw (TP;M3x6)  1 If bundled parts are used; If the parts bundled with this product are used, the symbol indicating the use of bundled parts is illustrated. Bundled parts In this procedure manual, the frequent operations are illustrated with symbols.
PAGE 2
1-2 Check of main power OFF Check that the main power switch of the main body is OFF. 1) Turn OFF the main power switch of the main body. 2) Check that the indication lamps on the operation panel and the main power lamp are out, and pull out the power plug. Installation procedure 1) Press cassette [1]. 2) Press button [2]. Open cartridge door unit [3]. Schematic diagram of attachment 3) Open ADF unit and reader unit [1].
PAGE 3
1-3 4) Remove claw [1] and arm cover [2]. 5) Disconnect arm [1] and push it back. 6) Shift the left side of main body [1] from the workbench by about 10 cm. 7) Open ADF unit and reader unit [1]. Reset claw [2].
PAGE 4
1-4 8) Open ADF unit and reader unit [1]. While applying stress to left cover [2] in the arrow direction, reset claw [3]. 9) Reset two bottom claws [2] with left cover [1] opened in the arrow direction. 10) Open ADF unit and reader unit [1]. Memo Remove the claw with right cover edge [2] reset from four rear cover hooks [1]. Reset claw [3]. Memo Reset claw [3] while holding left cover [2].
PAGE 5
1-5 11) Open ADF unit and reader unit [1]. Remove boss [2] from left cover [3]. 14) Remove connector [1] from the counter board.  Wire saddle [2] 12) Remove left cover [3]. Memo For attachment, attach left cover [1] aligning with four protrusions [2] on the left bottom cover. 15) Remove controller cover [1].  Six screws [2] (Removed screws are used in step 19).)  Hook [3] 13) After removing the left cover, put the main body at the center of the workbench.
PAGE 6
1-6 16) Attach Flat cable [1] on the main controller board [2]. CAUTION: ・Insert the Flat Cable face up. 17) Attach Wireless board [1]. ・Hook [2] ・Screw [3] (TP;M3×6) 18) Attach Flat cable [1] on the W-LAN board [2]. 19) Put all covers back.
PAGE 7
1-7 Note ■Put following sentences outside of the host device if the FCC ID on the module cannot be seen from exterior. ・“Contains Transmitter Module FCC ID: AZDFM48944” or “Contains FCC ID: AZDFM48944” ・“Contains Transmitter Module IC: 498D-FM48944” or “Contains IC: 498D-FM48944” ■User’s manual of the host device should contain sentences listed below. This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.