PUB.
Introduction Important Usage Instructions WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. COPYRIGHT WARNING: Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.
The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident. CAUTION: • Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries. • Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc. Important Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
IMPORTANT SAFETY INSTRUCTIONS In these safety instructions the word “product” refers to the Canon HD Camcorder VIXIA HF M30 A / VIXIA HF M31 A / VIXIA HF M300 A and all its accessories. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth.
21 22 23 24 25 26 27 28 29 Placing or Moving — Do not place on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
30 Damage Requiring Service — Disconnect this product from the wall outlet and all power sources including battery, and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If any liquid has been spilled onto, or objects have fallen into, the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally even if you follow the operating instructions.
Trademark Acknowledgements • The SD logo is a trademark. The SDHC logo is a trademark. • Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. • Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. • “x.v.Color” and the “x.v.Color” logo are trademarks. • HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Exciting Features and New Functions 1 High-Definition Video Your camcorder’s full high-definition image sensor (Full HD CMOS) captures video at a resolution of 1,920 x 1,080 1,080 pixels2. Videos are then recorded in the lines memory in high definition, using AVCHD specifications3.
Smart AUTO (0 43) Smart AUTO automatically selects the best scene mode for the scene you want to shoot. You get spectacular recordings every time without worrying about settings. Video Snapshot Just point the camcorder and it will automatically select the best settings for your subject (0 68) Shoot or capture short scenes and arrange them into a video clip set to your favorite background music.
Enjoying your Recordings on Other Devices Connect the camcorder to the optional DW-100 DVD Burner (0 131, 135) Connect the camcorder to an HDTV (0 124) AVCHD discs4 Photo DVDs SD AVCHD-compatible HDTVs and digital recorders with an SD memory card slot5. Play video directly from your recorded memory card Eye-Fi Use an Eye-Fi card (0 145) to wirelessly upload recordings to your computer or a video sharing Web site. Save or upload to the Web. Use the supplied software ImageMixer 3 SE (0 128, 141).
Table of contents Introduction 8 16 18 18 20 Exciting Features and New Functions About this Manual Getting to Know the Camcorder Supplied Accessories and CD-ROMs Names of Parts Preparations 23 23 26 28 30 30 31 32 35 35 36 36 37 37 38 38 39 40 Getting Started Charging the Battery Pack Preparing the Accessories Adjusting the Position and Brightness of the LCD Screen Basic Operation of the Camcorder Using the Touch Screen Operating Modes Using the Menus First Time Settings Setting the Date and T
Dual Shot Mode 42 Basic Recording 42 43 46 47 Shooting Video and Taking Photos in Dual Shot Mode About the Smart AUTO mode Zooming Quick Start Function Video 49 49 52 54 55 56 58 58 59 60 63 64 65 66 68 68 69 70 73 74 74 76 77 78 79 80 82 Basic Playback Playing Back the Video The Index Selection Screen: Selecting the Content to Play Back 3D Flip View Narrowing Down the Scenes Shown in the Index Screen Deleting Scenes Advanced Functions Shooting Video in y Manual Mode Selecting the Video Quality (
83 84 85 87 89 93 94 94 96 98 Using the Mini Advanced Shoe Using an External Microphone Using a Zoom Remote Controller Selecting the Playback Starting Point Playing Back Scenes Set to Background Music Onscreen Displays and Data Code Playlist and Scene Operations Editing the Playlist: Adding, Deleting, Moving and Playing Back Capturing Photos and Video Snapshot Scenes from a Movie Dividing Scenes Photos 100 Basic Playback 100 102 Viewing Photos Deleting Photos 104 Additional Functions 104 105 107 109
External Connections 121 Terminals on the Camcorder 122 Connection Diagrams 124 Playback on a TV Screen 126 Saving and Sharing Your Recordings 126 128 131 135 139 140 141 e Copying Recordings to a Memory Card Saving Recordings on a Computer Saving Movies onto High-Definition Discs (AVCHD/Blu-ray Discs) e Saving Movies onto Standard-Definition Discs (DVD) Saving Photos on Photo DVDs Copying Recordings to an External Video Recorder e Uploading Movies to Video Sharing Web Sites Additional Information 1
About this Manual Thank you for purchasing the Canon VIXIA HF M31 / VIXIA HF M30 / VIXIA HF M300. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubleshooting (0 168). Conventions Used in this Manual • • IMPORTANT: Precautions related to the camcorder’s operation. NOTES: Additional topics that complement the basic operating procedures.
indicates that a function is available in the operating mode indicated and indicates that the function is not available. For a detailed explanation refer to Operating Modes (0 31). Brackets [ ]are used to refer to control buttons and menu options you will touch on the screen and to other onscreen messages and displays. Self Timer Operating modes: [FUNC.] 8 [MENU] 8 8 8 [Self Timer] 8 [A On n] 8 [a] • n appears. • Repeat, selecting [B Off], to turn off the self timer. mode: In record pause mode, press g.
Getting to Know the Camcorder Supplied Accessories and CD-ROMs The following accessories are supplied with the camcorder: XCA-570 Compact Power Adapter (incl. power cord) BP-808 Battery PackW XWL-D89 Wireless Controller (incl.
The following CD-ROMs and software are supplied with the camcorder: • PIXELA Application - Disc 1 CD-ROM* and ‘PIXELA Applications’ Installation Guide - ImageMixer 3 SE Transfer Utilities – Software for saving and transferring movies and music files you can use as background music. • PIXELA Application - Disc 2 CD-ROM* - ImageMixer 3 SE Video Tools – Software for managing, editing, and playing back movies. • Y Instruction Manual/Photo Applications Ver.34.
Names of Parts Left side view Right side view Front view 20 Introduction 1 DISP. (onscreen display) button (0 93)/ BATT.
Top view l A S q a S s S d S S f g S h S S j k S S l q D a D LCD panel Mini advanced shoe (0 83) Mode switch (0 31) PHOTO button (0 42, 104) Zoom lever (0 46) VIDEO SNAP (video snapshot) button (0 68) POWER button ON/OFF (CHG) (charge) indicator: Green – ON Orange – Standby (0 47) Red – Charging (0 23) Remote sensor (0 26) LCD touch screen (0 28, 30) POWERED IS button (0 65)/ WEB button* (0 141) Battery attachment unit (0 23) START/STOP button (0 42, 58) DC IN terminal (0 23) * e only.
Bottom view s Serial number D d Tripod socket (0 187) D Wireless Controller WL-D89 1 START/STOP button (0 42, 58) 2 b (index selection) button (0 52) Press and hold for more than 2 seconds to switch between shooting and playback mode. 3 MENU button (0 33, 151) 4 DISP.
Preparations This chapter describes basic operations, such as using the touch panel, navigating the menus, and first time settings to help you learn more about your camcorder. Getting Started Charging the Battery Pack The camcorder can be powered with a battery pack or directly using the compact power adapter. Charge the battery pack before use.
5 Charging will start when the camcorder is turned off. • If the camcorder was on, the green ON/OFF (CHG) indicator will go out when you turn off the camcorder. After a moment, the ON/OFF (CHG) indicator will start flashing in red (battery pack charging). The red ON/ OFF (CHG) indicator will go out when the battery pack is fully charged. • If the indicator flashes quickly, refer to Troubleshooting (0 168).
• To prevent equipment breakdowns and excessive heating, do not connect the supplied compact power adapter to voltage converters for overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc. NOTES • The battery pack will be charged only when the camcorder is off. • If remaining battery time is an issue, you can power the camcorder using the compact power adapter so the battery pack will not be consumed. • Charged battery packs continue to discharge naturally.
Preparing the Accessories Wireless Controller First, insert the supplied CR2025 lithium button battery into the wireless controller. 1 Press the tab in the direction of the arrow and pull out the battery holder. 2 Place the lithium button battery with the + side facing up. 3 Insert the battery holder. Tab To use the wireless controller Point the wireless controller at the camcorder’s remote sensor when you press the buttons.
Grip Belt and Straps Fasten the grip belt. Adjust the grip belt so that you can reach the zoom lever with your index finger, and the g button with your thumb. To remove the grip belt 1 Lift the padded handgrip's flap and detach the strap from the Velcro pad. 2 Pull the strap to remove it first from the front bracket on the camcorder, then to unthread it from the handgrip and finally to remove it from the rear bracket on the camcorder.
To attach an optional wrist strap Pass the attaching end of the wrist strap through the rear bracket on the camcorder, thread the wrist strap through the loop and fasten. You can also attach the wrist strap to the strap mount on the grip belt to use both for extra convenience and protection. To attach an optional shoulder strap Pass the ends of the shoulder strap through the strap mount on the grip belt and adjust the length of the strap.
180° 180° 90° Subject can monitor the LCD screen NOTES • About the LCD screen: The screen is produced using extremely high-precision manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of the pixels may occasionally misfire or appear as black, red, blue or green dots. This has no effect on the recorded image and does not constitute a malfunction. LCD Backlight When recording in bright places it may be difficult to use the LCD screen.
Basic Operation of the Camcorder Using the Touch Screen The control buttons and menu items that appear on the touch screen change dynamically depending on the operating mode and the task you are performing. With the intuitive touch screen interface you have all the controls at your fingertips. Touch Touch a menu item to select it, or a control button to perform the corresponding action.
• For details about how to take care of the touch screen, refer to Handling Precautions (0 186), Cleaning (0 191). Operating Modes Recording When recording video or photos, the camcorder’s operating mode is determined by the position of the mode switch and the onscreen control buttons.
Initial mode Operating mode Press S in or mode. Press S in Operation Playing back movies ([Original] index screen) (0 49). mode. Viewing photos ([Photos] index screen) (0 100). NOTES • e When switching to a playback mode, the memory selected for playback will be the same currently used for recording. • You can also press and hold B on the wireless controller for more than 2 seconds to switch between recording and playback mode.
In and mode, touch [Edit] to display a similar panel containing the various operations that are available after selecting one or more scenes or photos (for example, deleting, adding scenes to the playlist, protecting photos, etc.). Touch the control button of the desired operation. Example of the Edit panel in mode Touch the control button of the desired operation The Setup Menus 1 or [FUNC.] mode only: Touch 2 Touch [MENU] to open the setup menus.
NOTES • A small font size is used in menu screens so you can see the options currently selected. You can enlarge the font size by setting 6 8 [Font Size] to [A Large] but only the icons of the currently selected options will appear on the screen.
First Time Settings Setting the Date and Time You will need to set the date and time of the camcorder before you can start using it. The [Date/Time] screen will appear automatically when the camcorder’s clock is not set. When the [Date/Time] screen appears, the year will be selected. 1 Touch a field you want to change (year, month, day, hours or minutes). 2 Touch [Z] or [O] to change the field as necessary. 3 Set the correct date and time by changing all the fields in the same way. 4 Touch [Y.M.D], [M.
Changing the Language The default language of the camcorder is English. You can set it to one of 22 other languages. Operating modes: [FUNC.]* 8 [MENU] 8 6 8 [Language a] 8 Desired language 8 [a] * Only when performing the procedure in a recording mode. NOTES • Some control buttons, such as [ZOOM], [FUNC.] or [MENU], will appear in English regardless of the language selected. Changing the Time Zone Change the time zone to match your location. The default setting is New York.
Using a Memory Card Memory Cards Compatible for Use with the Camcorder You can use commercially available SDHC (SD high capacity) memory cards and SD memory cards with this camcorder. However, depending on the memory card, you may not be able to record movies. Refer to the table below. As of October 2009, the movie recording function has been tested using SD/SDHC memory cards made by Panasonic, Toshiba and SanDisk.
Inserting and Removing a Memory Card Make sure to initialize (0 40) all memory cards before using them with this camcorder. 1 Turn off the camcorder. Make sure the ON/OFF (CHG) indicator is off. 2 Open the memory card slot cover. 3 Insert the memory card straight, with the label facing up, all the way into the memory card slot until it clicks. 4 Close the memory card slot cover. Do not force the cover closed if the memory card is not correctly inserted.
POINTS TO CHECK • Be sure you understand the information provided in Eye-Fi Cards (0 37) before using an Eye-Fi card. [FUNC.] 8 [MENU] 8 8 8 [Rec Media for Movies] or [Rec Media for Photos] 8 [f] (built-in memory)or [g] (memory card)* 8 [a] * When selecting the memory, you can check the approximate available recording time/number of photos, based on currently used settings.
NOTES • Any of the following actions will deactivate the relay recording function: - Turning off the camcorder. - Opening the memory card slot cover. - Changing the position of the mode switch. - Changing the camcorder's operating mode. - Selecting the memory card as the memory for recording movies. Initializing the Built-in Memory (e only) or Memory Card Initialize memory cards when you use them with this camcorder for the first time.
* Touch this option if you want to physically erase all the data rather than just clear the file allocation table of the memory. ** If you selected the [Complete Initialization] option, you can touch [Cancel] 8 [OK] to cancel the initialization while it is in progress. All recordings will be erased and the memory can be used without any problem. IMPORTANT • Initializing the memory will permanently erase all recordings. Lost original recordings cannot be recovered.
Dual Shot Mode This chapter covers how to easily record video and photos in the all-automatic Dual Shot mode, and how to use basic shooting functions like zoom and Quick Start. To enjoy full access to menus and more advanced functions, refer to the relevant chapters for video (0 58) and photos (0 104). Basic Recording Shooting Video and Taking Photos in Dual Shot Mode Operating modes: 1 Set the mode switch to 5. 2 Turn on the camcorder. • e By default, movies and photos are recorded in the built-in memory.
When you have finished recording 1 Make sure that the ACCESS indicator is off. 2 Turn off the camcorder. 3 Close the LCD panel. About Dual Shot • Only the following functions are available in mode. - Zoom (0 46). - Quick Start (0 47). - Video snapshot (0 68). - Advanced image stabilization modes (0 64) to shoot video while walking or to stabilize the shot while zooming in on faraway subjects (telephoto).
Smart AUTO icons Background → (color of the icon) Bright (grey) Subject ↓ Blue skies (light blue) Vivid colors (green/red) People (stationary) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) People (moving) Subjects other than people, such as landscapes Close objects Sunsets (orange) — — — The icon in parentheses appears under backlight conditions.
• Be sure to save your recordings regularly (0 126), especially after making important recordings. Canon shall not be liable for any loss or corruption of data. • When recording photos on an Eye-Fi card, photos will be uploaded automatically if you are within the range of a configured network. Always verify that Eye-Fi cards have been approved in the country/region of use. See also Using an Eye-Fi card (0 146).
Zooming Operating modes: There are three ways you can zoom in and out: using the zoom lever on the camcorder, using the zoom buttons on the wireless controller or using the zoom controls on the touch screen. In addition to the 15x optical zoom*, in mode, you can turn on the 300x digital zoom with the 7 8 [Digital Zoom] setting. * When [Image Stabilizer] (FUNC. panel) is set to [P Dynamic], you can use the advanced zoom to magnify the image up to 18x.
2 Touch the zoom controls to operate the zoom. Touch anywhere within the Q area to zoom out or anywhere within the P area to zoom in. Touch closer to the center for a slow zoom ([Speed 1]); touch closer to the e/d icons for faster zooms ([Speed 3]). 3 Touch [a] to hide the zoom controls. NOTES • Keep at least 1 m (3.3 ft.) away from the subject. At full wide angle, you can focus on a subject as close as 1 cm (0.39 in.).
2 When you wish to resume recording, open the LCD panel. The ON/OFF (CHG) indicator turns back green and the camcorder is ready to record. IMPORTANT • Do not disconnect the power source during standby mode (while the ON/OFF (CHG) indicator is lit in orange). NOTES • The camcorder will not enter standby mode if the LCD panel is closed while the ACCESS indicator is on or flashing or while a menu is being displayed.
Video This chapter covers functions related to movies, including playback, advanced shooting, advanced functions and playlist and scene operations. For details about basic video shooting, refer to Dual Shot Mode (0 42). Basic Playback Playing Back the Video Operating modes: 1 Press S. You can also press and hold B on the wireless controller for more than 2 seconds to switch between shooting and playback mode. 2 Open the [Original] index screen, if it is not displayed.
A Memory being read B Index screen currently displayed C Drag your finger left for the next index page* D Drag your finger right for the previous index page* E Select a different index screen to read different content or from a different memory (e only) (0 52) F Scene's timeline (0 87) and recording information G Narrow down the scenes shown in the index screen (0 55) * While browsing through index pages, a scroll bar will appear at the bottom of the screen for a few seconds.
A Stop the playback. B Jump to the beginning of the scene. Double-tap to jump to the previous scene. C Pause the playback. D Drag your finger left and right along the volume bar to adjust the volume. E Touch anywhere else to hide the playback controls. F Fast playback backward*. G Jump to the next scene. H Fast playback forward*. * Touch several times to increase the playback speed to approximately 5x → 15x → 60x the normal speed.
IMPORTANT • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover. - Do not disconnect the power source or turn off the camcorder. - Do not change the camcorder’s operating mode. • You may not be able to play back with this camcorder movies recorded on a memory card using another device.
A e Touch the tab of the desired memory: built-in memory or memory card. B Touch a control button to select the content you want to play back. Options [Original] Original movies as you recorded them. [Playlist] Scenes that were added to the playlist (0 94) and may have been rearranged to your liking. [3D Flip View] See the following section (0 54). [Photos] Display the photo index screen.
3D Flip View 3D Flip View is a fun way to display your video recordings (original scenes) in a 3D layout, organized by recording date. In any index screen, touch [b] 8 [3D Flip View]. During single photo view, touch the screen once to display the controls then touch [Q] to open the [Photos] index screen. A Drag your finger up and down to browse through the scenes recorded in the displayed date. B Drag your finger left to go to the next date with recordings. C Touch the scene in the front to play it back.
Narrowing Down the Scenes Shown in the Index Screen From the [Original] index screen, you can narrow down the scenes shown, leaving only scenes that were recorded on a specific date or only those scenes in which people's faces were detected. Operating modes: Showing Only Scenes that Contain People’s Faces This will narrow down the scenes shown in the [Original] index screen, leaving only scenes that were recorded using face detection (0 66) and in which people's faces were detected.
2 Open the calendar screen. [y All Scenes] 8 [Scenes by Date] • Dates that contain scenes (that is, movies were recorded on that date) appear in black against a silver background. Dates without recordings appear grayed out. • Touch [y] or [A] to jump to the previous/next calendar month that contains recordings. 3 Touch the desired date. The selected date appears instead of [All Scenes]. To show all scenes again, touch [y (the date displayed on the screen)] and then [All Scenes].
3 Touch on the individual scenes you want to delete. • A checkmark O will appear on scenes selected. Touch a selected scene again to remove the checkmark. • To select all the scenes at once: Touch [Select All] instead of touching individual scenes. (Remove in advance any checkmarks from scenes you may have selected individually.) 4 Delete the scenes. [Edit] 8 [Delete] 8 [Yes]* 8 [OK] * Touch [Stop] to interrupt the operation while it is in progress. Some scenes may be deleted nevertheless.
Advanced Functions Shooting Video in y Manual Mode When the mode switch is set to y (Manual mode), you can enjoy full access to the menus and manually adjust the exposure, focus, white balance and many more of the camcorder's settings to your preference. Even in mode, though, the camcorder can help you with the settings. For example, by using Special Scene recording programs (0 60). Operating modes: 1 Set the mode switch to y. 2 Turn on the camcorder.
NOTES • The zoom, Quick Start function, power saving modes, etc. operate the same way in mode as in mode. For details, refer to Dual Shot Mode (0 42). Selecting the Video Quality (Recording Mode) The camcorder offers 5 recording modes. Changing the recording mode will change the recording time available on the memory. Select MXP or FXP mode for better movie quality; select LP mode for longer recording times. The following table gives approximate recording times. Operating modes: [FUNC.
Approximate recording times Recording mode → Default value MXP1 FXP1 XP+ SP LP 4 GB Memory card 20 min. 30 min. 40 min. 1 hr. 10 min. 1 hr. 30 min. 8 GB Memory card/ 6 Built-in memory2 40 min. 1 hr. 1 hr. 25 min. 2 hr. 20 min. 3 hr. 16 GB Memory card 1 hr. 25 min. 2 hr. 5 min. 2 hr. 50 min. 4 hr. 45 min. 6 hr. 5 min. 32 GB Memory card/ a Built-in memory2 2 hr. 55 min. 4 hr. 10 min. 5 hr. 45 min. 9 hr. 35 min. 12 hr. 15 min.
[GSports] To record sports scenes such as tennis or golf. [q Night Scene] To record nightscapes with lower noise. [ISnow] To record in bright ski resorts without the subject being underexposed. [JBeach] To record on a sunny beach without the subject being underexposed. [KSunset] To record sunsets in vibrant colors. [p Low Light] [LSpotlight] [MFireworks] To record in low-light situations. To record spotlit scenes. To record fireworks.
[rUnderwater] To record underwater scenes in natural colors. [sSurface] To record after getting out of the water, such as on a boat after diving. NOTES • [F Portrait]/[G Sports]/[I Snow]/[J Beach]: The picture may not appear smooth during playback. • [F Portrait]: The blur effect of the background increases the more you zoom in (P). • [I Snow]/[J Beach]: The subject may become overexposed on cloudy days or in shaded places. Check the image on the screen.
- p will appear on the screen when the camcorder's temperature becomes too high. If this happens, turn off the camcorder, take it out of the waterproof case and keep it in a cool place until the temperature goes down. If the camcorder becomes too hot, it will turn off automatically. - When making recordings underwater with the [r Underwater] recording program, the image on the LCD screen will appear redder than the actual subject. This will not affect the recording.
Operating modes: To change the frame rate [FUNC.] 8 [MENU] 8 8 8 [Frame Rate] 8 [E PF24] 8 [a] Advanced Image Stabilization The image stabilizer reduces camcorder blur (blur due to the camcorder moving) so you can get nice, stable shots. Select the image stabilization mode according to the shooting conditions. Operating modes: In mode: [FUNC.
Powered IS When shooting video, you can use Powered IS to make the image stabilization even more powerful. Powered IS is most effective when you are stationary and zooming in on far subjects using high zoom ratios (the more you approach the telephoto end). Holding the LCD panel with your left hand will add to the stability of the shot. Press and hold Y as long as you want to activate Powered IS. • Z appears in yellow, while Powered IS is activated.
1 Activate the pre-recording function. [FUNC.] 8 [d Pre REC] 8 [A On] 8 [a] • d appears. • Repeat, selecting [B Off], to turn off pre-recording. 2 Press g. The scene recorded in the memory will start 3 seconds before g was pressed. NOTES • While pre-recording is activated, the camcorder will not emit any notification sounds.
POINTS TO CHECK • Select a recording program other than [q Night Scene], [p Low Light], [M Fireworks] or [r Underwater]. By default, face detection is activated. If the function was turned off, perform the following procedure to turn it on. [FUNC.] 8 [MENU] 8 7/8 8 [Face Detection & Tracking] 8 [A On o] 8 [a] To select the main subject If there is more than one person in the picture, the camcorder will automatically select one person it determines is the main subject.
Touch & Track When recording people, face detection (0 66) will track the main subject and keep it always in focus. But also when recording other moving subjects such as your pet, a moving vehicle or people not facing the camera directly, you can use Touch & Track to keep your subject in focus at all times. Operating modes: 1 Make sure face detection is activated (0 66). 2 Point the camcorder at a moving subject and touch the subject on the touch screen.
1 Press z. • A blue border appears on the screen. • Press z again to return to normal video recording mode. 2 Press g. • By default, the camcorder records for about 4 seconds (the blue frame serves as a visual progress bar) and then automatically returns to record pause mode. You can change the length of video snapshot scenes with the 8 8 [Video Snapshot Length] setting. • When the camcorder stops recording, the screen will momentarily turn black as if a camera shutter had released.
To fade in/out Press g in record pause mode (M) to start recording with a fade in. Press g while recording (N) to fade out and pause the recording. Options ( Default value) [N Off] Select this setting when you do not intend to use the digital effects. [2 Black & White]* Records movies and photos in black and white. [3 Sepia]* Records movies and photos in sepia tones for an “old” look.
[FUNC.] 8 [Rec. Programs] 8 [B Shutter-Pri. AE] or [C Aperture-Pri. AE] 8 Drag your finger left and right along the dial to set the desired shutter speed (B) or aperture value (C) 8 [a] Options ( Default value) [A Programmed AE] The camcorder automatically adjusts the aperture and shutter speed to obtain the optimal exposure for the subject. [B Shutter-Pri. AE] Set the shutter speed value. The camcorder automatically sets the appropriate aperture value. [C Aperture-Pri. AE] Set the aperture value.
Shutter Speed and Aperture Value Guidelines XWith slower shutter speed you can add a nice motion blur and sense of movement. With faster shutter speeds you can “freeze the action” for powerful images of moving subjects.
Manual Exposure Adjustment At times, backlit subjects may appear too dark (underexposed) or subjects under very strong lights may appear too bright or glaring (overexposed). To correct this, you can adjust the exposure manually or use the Touch AE function to automatically set the optimal exposure for the subject you select. This is convenient when the brightness of the subject you want to shoot is noticeably brighter/darker than the general brightness of the image.
NOTES • If the recording program is changed during exposure lock, the camcorder will return to automatic exposure. • When shooting subjects with a strong light source behind them, the camcorder automatically corrects for the backlight. You can turn off the automatic backlight correction with the 7/8 8 [Auto Backlight Correction] setting. Automatic Gain Control (AGC) Limit When recording in dark surroundings, the camcorder will automatically increase the gain to try to get a brighter picture.
POINTS TO CHECK • Adjust the zoom before you start the procedure. 1 Open the manual focus screen. [FUNC.] 8 [X Focus] 2 Touch a subject that appears inside the X frame. • The Touch AF mark (P) will flash and the focusing distance will be adjusted automatically. You have the option to further adjust the focus manually as necessary. • You can touch [2] instead to adjust the focus manually without activating the Touch AF function. • The manual focus controls and the current focusing distance appear.
White Balance The white balance function helps you to accurately reproduce colors under different lighting conditions so that white objects will always look truly white in your recordings. Operating modes: POINTS TO CHECK • Select a recording program other than the Special Scene recording programs. [FUNC.] 8 [m White Balance] 8 Desired option* 8 [a] * When you select [g Custom WB], set the custom white balance with the following procedure before touching [a].
NOTES • When you select the custom white balance: - Set 7 8 [Digital Zoom] to [B Off]. - Reset the white balance when you change locations or the lighting or other conditions change. - Depending on the light source, g may keep flashing. The result will still be better than with [Y Automatic].
Options ( Default value) [U Off] Records with no image enhancing effects. [V Vivid] Emphasizes the contrast and color saturation. [W Neutral] Tones down the contrast and color saturation. [X Low Sharpening] Records subjects with softened outlines. [Y Soft Skin Detail] Softens the details in the skin tone area for a more complimentary appearance. To obtain the best effect, use this setting when recording a person in close-up. Note that areas similar to the skin color may lack in detail.
NOTES • We recommend not using the mini video light while the optional Wideconverter or Tele-converter is attached; its shadow can appear on the screen. Using an External Video Light You can use the optional VL-5 Video Light or VFL-2 Video Flash Light when you need a video light that is stronger than the built-in mini video light. Attach the optional video light to the mini advanced shoe. • Refer to Using the Mini Advanced Shoe (0 83). • appears when you turn on the optional video light (ON or AUTO).
mode: Press j, first halfway to activate the autofocus and then fully. The camcorder will record the photo after a 10-second countdown*. The countdown appears on the screen. * 2 seconds when using the wireless controller. NOTES • Once the countdown has begun, any of the following actions will cancel the self timer. - Pressing g (when recording movies) or j fully (when recording photos). - Turning off the camcorder. - Changing the camcorder’s operating mode. - Setting the camcorder to standby mode.
Manual audio level adjustment Audio level indicator Current audio level Audio level adjustment bar 2 Touch and hold [y] or [A] to adjust the audio recording level as necessary. As a guideline, adjust the audio recording level so that the audio level meter will go to the right of the -12 dB mark (yellow area) only occasionally. 3 Touch [a] to lock the audio recording level at the current level.
Using Headphones Use headphones for playback or to check the audio level while recording. The headphones are connected to the AV OUT/X terminal, which is used for both the headphones and the audio/video output. Before connecting the headphones, follow the procedure below to change the function of the terminal from AV output to X (headphones) output. Operating modes: * * Headphones can be used also in mode but the function of the terminal cannot be changed in this mode.
IMPORTANT • When using headphones, make sure to lower the volume to an appropriate level. • Do not connect the headphones to the AV OUT/X terminal if the J icon does not appear on the screen. The noise output in such case may be harmful to your hearing. NOTES • Use commercially available headphones with a ∅ 3.5 mm minijack. • Even if [AV/Headphones] was set to [J Headphones] in a playback mode, the function of the AV OUT/X terminal will return automatically to AV output when you turn off the camcorder.
NOTES • Accessories designed for the Advanced Accessory Shoe * cannot be used with this camcorder. Look for video accessories bearing this logo to ensure compatibility with the mini advanced shoe. Using an External Microphone When recording in very quiet surroundings, the built-in microphone may pick up the sound of the camcorder's internal machinery. In such case, we recommend using an external microphone.
Using other microphones You can also use commercially available microphones. Connect the external microphone to the MIC terminal. Use commercially available condenser microphones with their own power supply. You can connect almost any stereo microphone with a ∅ 3.5 mm plug but audio recording levels may vary. NOTES • When using the optional SM-V1 Surround Microphone, change the microphone's directionality mode with the 7 8 [Surround Mic Directionality] setting.
Attach the optional RA-V1 Remote Control Adapter to the mini advanced shoe. Refer to Using the Mini Advanced Shoe (0 83). appears. For details about using the adapter, refer to the instruction manual of the RA-V1. For details about using the zoom remote controller, refer to the instruction manual of the ZR-2000 or ZR-1000.
Selecting the Playback Starting Point If you have a very long scene, you may want to start playing back the scene from a certain point. You can use the movie timeline to break the scene to segments at fixed time intervals ranging from 6 seconds to 6 minutes. If you recorded movies using face detection (0 66), you can display the scene divided into segments every time the camcorder registered a change in the main subject of the scene. Operating modes: 1 Open the [Original] or [Playlist] index screen.
A Touch twice to return to the index screen. B Previous/next scene. C Drag your finger left along the ruler to display the next 5 frames. D Current scene / Total number of scenes. E Scene's recording mode and length. F Recording date and time. G Drag your finger right along the ruler to display the previous 5 frames. H Currently selected interval between frames (or [o Faces]).
Playing Back Scenes Set to Background Music You can play back video snapshot scenes, scenes in the playlist and photo slideshows set to background music (instead of the original sound). You can use one of the supplied music tracks or connect an external audio player to use your favorite songs as background music. Operating modes: Using One of the Supplied Music Tracks as Background Music The supplied Camcorder Supplemental Disc contains 3 music tracks you can use as background music.
A Select the desired music track. B Play back the original sound (no background music). C Delete the music track selected. D Listen to the music track selected. Touch again (B) to stop the playback. 3 Back in the index screen, touch a scene to start the playback set to the selected music track. In mode, touch a photo to go to single photo view and continue with the slideshow procedure (0 113).
2 Activate the external audio input. [MENU] 8 y / z 8 [External Audio Input] 8 [A On ] 3 Connect the external player to the camcorder's MIC terminal. 4 Adjust the audio input as necessary. • Start the music playback on the external player and adjust its volume according to the onscreen indications. When the audio input is in the correct range, stop the music playback and touch [a] on the camcorder.
NOTES • You can also add to the playlist just the video snapshot scenes you want to watch and arrange their playback order. • Initializing a memory card will permanently erase any music files you may have transferred to the card. (e The music files that come pre-installed in the built-in memory will be restored after it is initialized.) - Windows useres: Use the supplied software ImageMixer 3 SE to transfer music files from the supplied Camcorder Supplemental Disc to a memory card after it is initialized.
Onscreen Displays and Data Code You can turn most onscreen displays on or off.
Playlist and Scene Operations Editing the Playlist: Adding, Deleting, Moving and Playing Back Create a playlist to play back only the scenes you prefer and in the order of your choice. You can play back the scenes in the playlist using your favorite song as background music (0 89). Operating modes: Adding Scenes to the Playlist 1 Open the [Original] or [Video Snapshot] → [Original] index screen.
• e You can copy scenes from the built-in memory to the memory card (0 126) to include in the memory card’s playlist also scenes that were originally recorded in the built-in memory. Deleting Scenes from the Playlist Deleting scenes from the playlist will not affect your original recordings. 1 Open the [Playlist] index screen. You can touch [b] 8 [Video Snapshot] 8 [Playlist] to open the playlist of video snapshot scenes. 2 To delete a single scene, touch [c] and touch the scene you want to delete.
A Destination icon. B Move the scene to the position indicated by the destination icon. C Touch an empty box to select it as the destination. D Scene selected to be moved. E Original position of the scene and currently selected destination. Capturing Photos and Video Snapshot Scenes from a Movie You can capture video snapshot scenes, single photos or a series of continuous photos from a previously recorded scene.
NOTES • A video snapshot scene can be captured only during playback; it cannot be captured during playback pause mode. • e The captured video snapshot scene is saved to the same memory that contains the source scene. • Video snapshot scenes cannot be captured from any of the following types of scenes. - Scenes shorter than 1 second - Scenes that were edited using the supplied software ImageMixer 3 SE and were then written back to the camcorder.
To capture the photos 1 Play back the scene from which you want to capture the photo. 2 Pause the playback at the point you want to capture. 3 Press j fully. To capture a photo sequence, hold j pressed down. The scene will be played back by frames and each frame captured as a separate photo. 4 Touch [B] to return to the index screen. IMPORTANT • When capturing photos on an Eye-Fi card, photos will be uploaded automatically if you are within the range of a configured network.
2 Select the scene you want to divide and touch it to start playing it back. 3 Pause the playback at the point where you want to divide the scene. 4 Open the scene division screen. [Edit] 8 [Divide] 5 Bring the scene to a precise point, if necessary. • During playback pause: Touch [A] to play back the scene. Touch [F] or [E] to jump a frame backward/forward. • During playback: Touch [C] to pause the playback. Touch [J] or [I] for fast playback backward/forward. 6 Divide the scene.
Photos Refer to this chapter for details on taking photos (advanced shooting functions), viewing photos and printing them. For details about basic photo shooting, refer to Dual Shot Mode (0 42). Basic Playback Viewing Photos Operating modes: 1 Press S. 2 Open the [Photos] index screen, if it is not displayed. [b] 8 [Photos] 3 Look for the photo you want to play back. Move the zoom lever toward Q to show 15 photos per page; move it toward P to show 6 photos per page.
A Memory being read. B Index screen currently displayed. C Drag your finger left for the next index page. D Drag your finger right for the previous index page. E Select a different index screen to read different content or from a different memory (e only) (0 52). 4 Touch the photo you wish to view. • The photo is displayed in single photo view. • Drag your finger left/right to browse through the photos one by one.
IMPORTANT • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover. - Do not disconnect the power source or turn off the camcorder. - Do not change the camcorder’s operating mode. • The following image files may not be displayed correctly. - Images not recorded with this camcorder. - Images edited on or uploaded from a computer. - Images whose file names have been changed.
3 Touch on the individual photos you want to delete. • A checkmark O will appear on photos selected. Touch a selected photo again to remove the checkmark. • To select all the photos at once: Touch [Select All] instead of touching individual photos. (Remove in advance any checkmarks from photos you may have selected individually.) 4 Delete the photos. [Edit] 8 [Delete] 8 [Yes]* 8 [OK] * Touch [Stop] to interrupt the operation while it is in progress. Some photos will be deleted nevertheless.
Additional Functions Taking Photos in y Manual Mode Operating modes: 1 Set the mode switch to y. 2 Turn on the camcorder. • e By default, photos are recorded in the built-in memory. You can select the memory that will be used to record photos (0 38). • Please read the IMPORTANT section before using an Eye-Fi card. 3 Touch [3] to switch to mode. 4 Press j halfway. Once the focus is automatically adjusted, h will turn green and one or more AF frames will appear. 5 Press j fully.
NOTES • If the subject is not suitable for autofocus, h turns yellow. Adjust the focus manually (0 74). • When the subject is too bright, [Overexp.] will flash on the screen. In such case, use the optional FS-H37U ND filter. Deleting a Photo Right After Recording It You can delete a photo you have just recorded while reviewing it within the time set for the 8 8 [Photo Review Time] option.
Options Large capacity memory cards, like those usually used for video recording, can contain a very large number of photos. As a reference, the number of photos that can be recorded on a 1 GB memory card is given in the following table. NOTES • The actual number of photos that can be recorded will vary depending on the subject and shooting conditions. • The camcorder retains the last setting used even if you set the camcorder to mode.
Approximate number of photos available on a 1 GB memory card Memory card Photo size ↓ Default value Photo quality E [Super Fine] F [Fine] G [Normal] L 2100x1575 420 630 1,265 K 2304x1296 465 700 1,390 M 1600x1200 720 1,075 2,115 H 1920x10801 670 1,000 1,970 N 640x480 4,395 6,350 11,4303 S 848x4802 3,360 4,760 9,525 1 2 This size is only available for capturing photos from a movie (0 96). This size is only available for simultaneous recording in mode or mode.
2 Press j, first halfway to activate the autofocus and then fully to record the photo. Depending on the setting selected and shooting conditions, the flash will fire. Options ( Default value) [U Automatic] The flash fires automatically according to the brightness of the subject. [V Red-Eye Auto] The flash fires automatically according to the brightness of the subject. The assist lamp lights up to reduce the red-eye effect. [S Flash On] The flash always fires. [W Flash Off] The flash does not fire.
• About the AF-Assist Lamp: While you press j halfway, if the surroundings of the subject are too dark, the mini video light may light up briefly in order to enable the camcorder to focus more accurately (AFassist lamp). - You can also set 8 8 [AF-Assist Lamp] to [B Off] so the assist lamp is not activated. - The camcorder may not be able to focus even if the AF-assist lamp is on. - When the recording program is set to [r Underwater] or [s Surface], [AF-Assist Lamp] is automatically set to [B Off].
Options ( Default value) [A Single] Records a single photo. [D AE Bracketing] The camcorder records 3 photos using 3 different exposures (dark, normal, light in 1/2 EV steps), allowing you to choose the photo you like the best. [B Continuous], [C Hi-Speed Cont.] Captures a series of up to 60 photos as long as you hold j pressed down. There are two continuous shooting speed settings: normal (approx. 3 photos/second) and high speed (approx. 5 photos/second).
[FUNC.] 8 [MENU] 8 8 8 [Simultaneous Recording] 8 Desired photo quality* (top row)** 8 Desired photo size* (bottom row) 8 [a] * The number displayed on the right corner indicates the approximate number of photos that can be recorded with the current quality/size setting. ** Touch [X] if you do not intend to use simultaneous recording. Operating modes: While recording, or in record pause mode, press j to capture the photo.
Light Metering Mode The camcorder measures the light reflected from the subject in order to calculate the optimal exposure settings. Depending on the subject, you may want to change the way the light is measured and evaluated. Operating modes: POINTS TO CHECK • Select a recording program other than the Special Scene recording programs. [FUNC.] 8 [Metering Mode] 8 Desired option 8 [a] Options ( Default value) [Q Evaluative] Appropriate for standard shooting conditions, including backlit scenes.
Slideshow set to a music track 3 Touch the screen to display the playback controls, then touch [A] to play back the slideshow set to the selected music track. Slideshow not linked to the external audio 3 Touch the screen to display the playback controls, then touch [A] to start the slideshow. 4 Start the music playback on the external player. • Drag your finger left and right along the volume bar to adjust the volume. • Touch [C] to stop the slideshow. Hide the playback controls if necessary.
2 Drag your finger across the photo to display the area you want to see enlarged. To cancel the magnification, move the zoom lever toward Q until the frame disappears. Rotating Photos You can rotate photos 90 degrees to change their orientation. Operating modes: 1 In single photo view, select the photo you want to rotate. 2 Touch the screen to display the playback controls. 3 Rotate the photo.
The histogram and Exif information panel are displayed as well. Press h to hide the histogram and Exif information panel. The area to the right of the histogram represents highlights and the left side represents shadows. A photo whose histogram skews to the right is relatively bright; while one whose histogram peaks to the left, is relatively dark. Protecting Photos You can protect photos from accidental erasure.
[Edit] 8 [Protect] 8 [Protect]* 8 [OK] * Touch [Remove Protection] to remove the protection from the selected photos. IMPORTANT • Initializing the memory will permanently erase all recordings, including protected photos. - r Functions You Can Use when Taking Photos You can also use the following functions... The following functions and features of the camcorder can be used either for shooting video or for taking photos.
Printing Photos Printing Photos (Direct Print) The camcorder can be connected to any PictBridge-compatible printer. You can mark in advance the photos you want to print and set the desired number of copies as a print order (0 119). Canon printers: SELPHY printers of the CP, DS and ES series and PIXMA printers carrying the PictBridge logo. Operating modes: Connecting the Camcorder to the Printer 1 In single photo view, select a photo you want to print. 2 Turn on the printer.
• Refer also to the printer’s instruction manual. • If you have no intention to use the optional DW-100 DVD Burner, you can set 8 8 [USB Connection Type] to [N Computer/Printer] so the device type selection screen does not appear every time you connect the camcorder to a printer. • For best performance when connecting the camcorder to a PictBridgecompatible printer, we recommend keeping the number of photos in the memory to no more than 100 photos.
Print errors If an error occurs while printing, an error message (for example, [No paper]) will appear on the camcorder’s screen. Solve the problem referring to the error message list (0 183) and to the printer's instruction manual. • Canon's PictBridge-compatible printers: If printing does not resume automatically after you solved the problem, touch [Continue] to resume printing. If that option is not available, touch [Stop] and then restart printing from the beginning.
• To cancel the print order, set the number of copies to 0. 4 Drag your finger left/right to select another photo to mark with a print order or touch [a]. Setting Print Orders from the Index Screen 1 Open the [Photos] index screen. Check that you have selected the g tab (memory card). 2 Touch [a] to open the photo selection screen. 3 Touch on the individual photos you want to mark with a print order. • A checkmark O will appear on photos selected. Touch a selected photo again to remove the checkmark.
External Connections This chapter explains how to connect your camcorder to an external device such as a TV, VCR, or computer. Terminals on the Camcorder 1COMPONENT OUT Terminal* Access: Open the rear terminal cover. The component video terminal is for video only. When you use connection B do not forget the audio connections using the AV OUT/X terminal. 2USB Terminal Access: Open the side terminal cover. 3HDMI OUT Terminal* Access: Open the side terminal cover.
Connection Diagrams In the following connection diagrams, the left side shows the terminals on the camcorder and the right side shows (for reference only) an example of terminals on a connected device. Connection A HDMI Type: Digital Quality: High definition Output only Connect to a high-definition TV (HDTV) with an HDMI input terminal.
Connection B Component Video Type: Analog Quality: High Definition Output only Connect to a high-definition TV (HDTV) with component video input terminals. Change the following settings on the camcorder: - 6 8 [AV/Headphones] to [H AV] Red Blue CTC-100/S Component Cable (supplied) Green White STV-250N Stereo Video Cable (supplied) Red Connection C Composite Video Type: Analog Quality: Standard definition Output only Connect to a standard TV or a VCR with audio/video input terminals.
Connection D USB Type: Digital data connection Connect to a computer to save your recordings, to the optional DW-100 DVD Burner to create DVD discs from them, or to a printer to print out photos. USB Cable (supplied) NOTES • To be able to write back scenes and to transfer music files from the computer to the camcorder, power the camcorder using the compact power adapter and only then connect it to the computer using the supplied USB cable.
NOTES • To correctly play back movies recorded with x.v.Color (0 156) on an HDTV compatible with this standard, additional settings may be required on the connected HDTV. Refer to the TV’s instruction manual. • We recommend powering the camcorder using the compact power adapter. • Connection C: When you play back your 16:9 movies on standard TV sets with a 4:3 aspect ratio, the TV set will switch automatically to widescreen mode if it is compatible with the Video ID-1 system.
Saving and Sharing Your Recordings e Copying Recordings to a Memory Card You can copy your recordings only one-way: from the built-in memory to the memory card. Scenes and photos will be copied from the index screen you selected to the corresponding index screen on the memory card. Please read the IMPORTANT section (0 128) before using an Eye-Fi card. Copying Scenes Operating modes: 1 Open the index screen that contains the scenes you want to copy.
Copying a Single Photo Operating modes: 1 In single photo view, select the photo you want to copy. Check that you are viewing photos recorded in the built-in memory. (f appears next to the photo number.) 2 Touch the screen to display the playback controls. 3 Copy the photo. [Edit] 8 [Copy (G)] 8 [i Proceed] 8 [Yes] 4 Drag your finger left/right to select another photo to copy or touch [a]. Copying Photos from the Index Screen Operating modes: 1 Open the [Photos] index screen.
IMPORTANT • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover. - Do not disconnect the power source or turn off the camcorder. - Do not change the camcorder’s operating mode. • When copying photos onto an Eye-Fi card, photos will be uploaded automatically if you are within the range of a configured network. Always verify that Eye-Fi cards have been approved in the country/region of use.
Using the software See ‘ImageMixer 3 SE Software Guide’ (PDF file on the Transfer Utilities CD-ROM). Saving Photos With the supplied software Photo Applications you can save photos to your computer, and easily organize and edit them. Installation Install the software before you connect the camcorder to the computer for the first time. See also the relevant sections in the ‘Photo Application’ Instruction Manual (r PDF file). Install the Photo Applications module on the supplied Camcorder Supplemental Disc.
IMPORTANT • When the camcorder is connected to a computer: - Do not open the memory card slot cover and do not remove the memory card. - Do not access, change or delete any of the camcorder’s folders or files directly from the computer as this may result in permanent data loss. Always save your movies on the computer, and restore files to the camcorder, using only the supplied software ImageMixer 3 SE.
• If you connect the camcorder to the computer while it is set to mode, the process of creating scene thumbnails will start automatically. If your intention was to save photos to the computer, you can touch [Skip] to stop the process and use the computer’s Safely Remove Hardware function (Windows) or Eject function (Mac OS) to end the connection to the camcorder. Disconnect the USB cable, set the camcorder to mode and restore the connection.
3 For original recordings only: Choose whether to add to the disc all the scenes or only scenes that have not been previously added to a disc. When you create the disc from the [Playlist] index screen (including the playlist of video snapshot scenes), the disc will contain the entire playlist. [MENU] 8 8 8 [Add Recordings to Disc] 8 [All Scenes] or [Remaining Scenes] 8 [a] Connecting to the DW-100 DVD Burner and Creating AVCHD Discs 1 Turn on the DVD Burner. s Refer to Creating DVDs.
• When the last disc is finalized, [Task completed] will be displayed. Take out the disc and close the disc tray. When the data requires multiple discs After a disc is finalized, it will be ejected automatically and a message will appear. Insert the next disc and close the disc tray. To create an additional copy of the same disc After the operation is finished, insert a brand new disc, close the disc tray and repeat the operation.
Playing back AVCHD discs created with the DW-100 DVD Burner DW-100 AVCHD disc created with the DW-100 (no MXP scenes) AVCHD-compatible DVD players, Blu-ray Disc players DVD players not compatible with AVCHD* O a O * Do not insert a disc into an incompatible device, as you may not be able to eject the disc. Playing Back AVCHD Discs Using the DW-100 DVD Burner You can use the optional DW-100 DVD Burner and the camcorder also to play back high-definition (AVCHD) discs on a TV.
6 Select the scene you want to play back and touch it to start playing it back. IMPORTANT • While the camcorder is connected to the DVD Burner, do not open the memory card slot cover and do not remove the memory card. NOTES • Only AVCHD discs created with the DW-100 DVD Burner can be played back using the DVD Burner. • The camcorder’s menus cannot be accessed while the camcorder is connected to the DVD Burner.
Operating modes: Converting Scenes into Standard Definition 1 Power the camcorder using the compact power adapter. 2 Make sure there is a memory card in the camcorder with sufficient available space. 3 Open the [Original], [Playlist] or [Video Snapshot] → [Original]/ [Playlist] index screen. • Check that you have selected the f tab (built-in memory).
To select the bit rate Using a higher bit rate will result in better video quality for the converted scenes. [5] 8 [Bit Rate (Quality)] 8 Desired option 8 [f] 8 [f] NOTES • When converting scenes in the [Playlist] or [Video Snapshot] → [Original]/ [Playlist] index screen: - The scenes are converted with the selected background music (0 89) instead of the original sound. • When converting scenes in the [Playlist]: - All the scenes are merged into one converted scene.
4 Click [Disc writing] and continue the operation on the computer following the software's indications. See also ‘ImageMixer 3 SE Software Guide’ (PDF file on the Transfer Utilities CD-ROM). IMPORTANT • While the camcorder is connected to the computer, do not open the memory card slot cover and do not remove the memory card. • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover.
To play back standard-definition DVDs Standard-definition DVDs are created using DVD-Video specifications. Play back these DVDs using standard DVD players. NOTES • When the camcorder contains a large number of scenes to be saved on discs, it may take a long time for the connection to the DVD Burner (0 132, step 2) to be completed. For best performance, we recommend limiting the number of scenes to be saved to 500 or fewer scenes. • Standard-definition DVDs cannot be played back using the DW-100 DVD Burner.
To play back Photo DVDs Photo DVDs are created using DVD-Video specifications. Play back these DVDs using standard DVD players. If you computer has a DVD drive, you can play back the slideshow as a DVD and you can also access individual photos as JPG files. NOTES • Photo DVDs cannot be played back using the DW-100 DVD Burner.
2 Turn on the camcorder and set it to mode. Verify that 6 8 [AV/Headphones] is set to [H AV]. 3 Camcorder: Locate the scene you wish to copy and pause the playback shortly just before the desired scene. 4 Camcorder: Resume playback. By default, onscreen displays will be embedded in the output video signal. You can change the displays by repeatedly pressing h (0 93). 5 External device: Start recording when the scene you wish to copy appears; stop recording when it ends. 6 Camcorder: Stop playback.
Operating modes: Converting Scenes into Standard Definition 1 Power the camcorder using the compact power adapter. 2 Make sure there is a memory card in the camcorder with sufficient available space. 3 Open the [Original], [Playlist] or [Video Snapshot] → [Original]/ [Playlist] index screen. • Check that you have selected the f tab (built-in memory).
7 When the conversion is completed, a confirmation screen will appear. Connect the camcorder to the computer at this point (0 144) to continue uploading the converted videos to the Web or touch [End Without Connecting] to connect to the computer later. To embed the recording date and time The recording date and time will always be displayed on the converted scene.
• When converting scenes in the [Playlist]: - All the scenes are merged into one converted scene. - If the converted scene is too large, it will be split into smaller 10minute long scenes. - When converting only part of a scene, the maximum length of the converted scene will be 10 minutes from the starting (playback pause) point. - The playlist cannot be converted when its total playback time exceeds 2 hours and 30 minutes.
IMPORTANT • While the camcorder is connected to the computer, do not open the memory card slot cover and do not remove the memory card. • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover. - Do not disconnect the USB cable. - Do not disconnect the compact power adapter or turn off the camcorder or the computer.
IMPORTANT Using an Eye-Fi Card • This product is not guaranteed to support Eye-Fi card functions (including wireless transfer). In case of an issue with an Eye-Fi card, please check with the card manufacturer. Also note that an approval is required to use Eye-Fi cards in many countries or regions. Without approval, use of the card is not permitted. If it is unclear whether the card has been approved for use in the area, please check with the card manufacturer.
Additional Information This chapter contains troubleshooting advice, screen messages, handling and maintenance tips, and other information. Appendix: Menu Options Lists Menu items not available appear grayed out. For details about how to select an item, refer to Using the Menus (0 32). For details about each function, see the reference page. Menu options without a reference page are explained after the tables. Underlined menu options indicate default values. FUNC. Panel FUNC. Menu FUNC.
Control Button Setting options/Function 4 3 0 [S Flash] [U Automatic], [V Red-Eye Auto], [S Flash On], [W Flash Off] – z 107 [X Focus] [2] (manual focus): Toggle on (x) or off (w), Touch AF frame z z 74 [e Exposure] [y] (manual exposure): Toggle on (x) or off (w), Touch AE frame z z 73 [ZOOM] Zoom controls, g control z z 46 [P AGC Limit] [z Automatic], [y Manual]]: (0 dB - 24 dB) z – 74 [Metering Mode] [Q Evaluative], [S Center-Wt. Avg.
Setup Menus [Edit] Panel - Mode 1: Original scenes s: Playlist scenes (including the playlist only of video snapshot scenes) Z: Original video snapshot scenes u: SD scenes on the memory card (e only) Control Button 1 s Z u 0 Target Scenes/Function e [Copy (PUg)] [Selected Scenes] z – z – [All Scenes] z z z – [This Scene] (from the Timeline screen) z – z – e [Convert HDUSD (x DVD)] [Selected Scenes] z – z – [All Scenes] z z z – [This Scene] (from the Timeline screen) z – z
[Edit] Panel - Mode Index Screen Single Photo View 0 [Selected Photos], [All Photos] z 127 [Delete] z 102 [Protect] z 115 [Print Orders] z 119 z 114 Control Button e [Copy (PUg)] [Rotate] 150 Additional Information –
Setup Menus 7 / 8 Camera Setup Menu item 4 3 0 Setting options [Digital Zoom] [B Off], [G 60x], [H 300x] z – – [Zoom Speed] [I Variable], [J Speed 3], [K Speed 2], [L Speed 1] z z 46 [AF Mode] [R Instant AF], [S Normal AF] z z – [AF-Assist Lamp] [O Automatic], [B Off] – z 109 [Focus Priority] [U AiAF Frames], [W Center Frame], [B Off] – z – [Focus Assistance] [A On], [B Off] z z – [Face Detection & Tracking] [A On o], [B Off] z z 66 [Auto Backlight Correction] [A On],
[Digital Zoom]: Determines the Optical zoom Digital zoom operation of the digital zoom. The color of the indicator indicates the zoom. • When activated, the camWhite Light Dark corder will switch automatically blue blue to digital zoom when you zoom in beyond the optical zoom Up to 18x* 18x* 60x range. 60x 300x • With the digital zoom the image is digitally processed, so * 15x when [Image Stabilizer] is set to [Q Standard] or [j Off]. the image resolution will deteriorate the more you zoom in.
• Using focus assistance will not affect the recordings. It will be cancelled automatically after 4 seconds or when you start recording. [Auto Slow Shutter]: The camcorder automatically uses slow shutter speeds to obtain brighter recordings in places with insufficient lighting. • Minimum shutter speed used: 1/30; 1/12 when the frame rate is set to [E PF24]; 1/15 when it is set to [o PF30].
[Onscreen Markers]: You can display a grid or a horizontal line at the center of the screen. Use the markers as a reference to make sure your subject is framed correctly (vertically and/or horizontally). • Using the onscreen markers will not affect the recordings. [POWERED IS Button]: Determines the operation mode of the POWERED IS button. [Press and Hold]: Powered IS will be activated while you hold the button pressed down.
Menu item [Photo Quality/Size] 4 3 1 2 0 Setting options [K 2304x1296], [L 2100x1575], [M 1600x1200], [N 640x480] – z – – 105 [E Super Fine], [F Fine], [G Normal] [Photo Capture from Video] [A Single Photo], [B Photo Sequence] – – z – 97 [Photo Capture Quality] [P Super Fine / 1920x1080], [Q Fine / 1920x1080], [R Normal / 1920x1080] – – z – 97 [Memory Info] [P] (built-in memory), [g] (memory card) z z z z – [x.v.
[Memory Info]: Displays a screen where you can verify how much of the built-in memory (e only) or the memory card is currently in use (l total recording time and k total number of photos) and how much space remains available for recording. • Estimated figures about available movie recording time and available number of photos are approximate and based on the recording mode and photo quality/size settings currently in use. • In the information screen of a memory card you can also check its Speed Class.
• The photo number indicates the name and location of the file on the memory card. For example, the file name of a photo numbered 1010107 is “IMG_0107.JPG”, stored under the folder “DCIM\101CANON”. [USB Connection Type]: Select the connection protocol to use when connecting the camcorder to an external device using the supplied USB cable. [M DVD Burner]: To connect exclusively to the optional DW-100 DVD Burner. [N Computer/Printer]: To connect to a computer, printer or similar USB peripheral.
• When the TV type is set to [F Normal TV], during the playback of video originally recorded with an aspect ratio of 16:9, the picture will not be displayed fullscreen.
Menu item e [Initialize f/g] 4 3 1 2 0 Setting options [P Built-in Mem.], [g Mem. Card] z z z1 z 40 [Complete Initialization]: Toggle on (x) or off (w) d [Initialize g] [Complete Initialization]: Toggle on (x) or off (w) [Time Zone/DST] [S] (home time zone) or [V] (travel time zone): [New York], list of world time zones [U] (DST adjustment) z z z z 36 [Date/Time] [Date/Time]: – z z z z 35 [Date Format]: [Y.M.D], [M.D,Y], [D.M.
[Font Size]: Changes the size of the font for the menu and other screens. • When the font size is set to [A Large], some information may be displayed in shortened form (icons only, etc.). Some screens will be displayed using the small font size regardless of the setting. [Output Onscreen Displays] • When set to [A On], the camcorder’s onscreen displays will appear also on the screen of a TV or monitor connected to the camcorder. [LCD Brightness]: Adjusts the brightness of the LCD screen.
• You can set Quick Start to [B Off], for example, if the camcorder is set on a fixed position and you want to keep recording video with the LCD panel closed in order to conserve the battery's power. [Calendar Start Day]: Select the day on which the week in the calendar screen (0 55). [Battery Info]: Displays a screen where you can verify the battery charge (as a percentage) and the remaining recording time ( playback time ( , mode).
[Demo Mode]: The demonstration mode displays the camcorder's main features. It starts automatically when the camcorder is powered with the compact power adapter if you leave it turned on without a memory card for more than 5 minutes. • To cancel the demo mode once it has started, press any button or turn off the camcorder. [Reset All]: Resets all the camcorder's settings to default values. [Firmware]: You can verify the current version of the camcorder's firmware. This menu option is usually unavailable.
Appendix: Onscreen Icons and Displays Recording Movies (in Dual Shot mode) Smart AUTO mode (0 43) Onscreen zoom controls (0 46) Operating mode (0 31) In record pause mode: Total number of scenes 5 Memory operation (0 167) 6 Remaining battery time (0 167) 1 2 3 4 7 Zoom (0 46) 8 Recording mode (0 59) 9 Control button: Start/Stop video recording q Face detection frame (0 66) A a Touch & Track frame (0 68) A Additional Information 163
Recording Movies (in y Manual mode) s Control button: Open the FUNC.
Recording Photos (in y Manual mode) D Drive mode (0 109) k l Light metering mode (0 112) D q Control button: Last function used F ([MENU] in this case) a Self timer (0 79) F s Flash (0 107) F d Eye-Fi wireless communication F (0 145) f Number of available photos F g On the memory card e f In the built-in memory F Photo quality/size (0 105) g h Control button: Switch to movie F recording (0 58) j AF frame (0 152) F k Focus and exposure lock F (0 42, 104) l Camcorder shake warning (0 153) F Playing Movies
Viewing Photos Exif information panel g Control button: Open the setup G menus (0 151) h Protected photo mark (0 115) G j Current photo / Total number of G photos k Photo number (0 156) G l Histogram (0 114) G q Control button: Photo jump H (0 101) a Date and time of recording H 166 Additional Information H Control button: Slideshow (0 112) s d Control button: Open the Edit panel H (0 150) f Control button: Switch to [Photos] H index screen (0 100) g Manual focus (0 74) H h File size H j Photo size (0
5 Memory operation N Record, M Record pause, A Playback, C Playback pause, I Fast playback, J Fast reverse playback, G Slow playback, H Slow reverse playback, E Frame advance, F Frame reverse. 6 Remaining battery time • The icon shows a rough estimate of 100% 75% 50% 25% 0% the remaining charge as a percentage of the full charge of the battery pack. The remaining recording/playback time of the battery pack is displayed, in minutes, next to the icon.
Trouble? Troubleshooting If you have a problem with your camcorder, refer to this section. Sometimes what you think is a malfunction of the camcorder may have the simplest of solutions - please read the “CHECK THIS FIRST” box before going on to the more detailed problems and solutions. Consult your dealer or a Canon Service Center if the problem persists.
- The camcorder cannot communicate with the battery pack attached. Such battery packs cannot be charged using this camcorder. A noise can be heard from the compact power adapter. - A faint sound can be heard while the compact power adapter is connected to a power outlet. This is not a malfunction. The battery pack is exhausted extremely quickly even at normal temperatures. - The battery may have reached the end of its battery life. Buy a new battery pack. Recording Pressing g will not start recording.
After using the camcorder for a long time, it becomes hot. - The camcorder may become hot after using it continuously for long periods of time; this is not a malfunction. If the camcorder becomes unusually hot or it becomes hot after using it only for a short while, it may indicate a problem with the camcorder. Consult a Canon Service Center. Playback Cannot add scenes to the playlist. - The playlist can contain a maximum of 999 scenes.
When playing scenes/a slideshow linked to external audio, the video playback is not correctly linked to the external player. - The volume of external player may be too low. Try increasing the volume of the external player. Cannot divide scenes - You cannot divide scenes recorded or edited using another device. - The memory is full. Delete some recordings (0 56, 102) or initialize the memory (0 40) to free some space.
The red ON/OFF (CHG) indicator flashes very slowly ( one flash at 2second intervals). - The temperature of the battery pack is outside the charging range. If the battery pack’s temperature is below 0 °C (32 °F), warm it before charging it; if it is above 40 °C (104 °F), let the battery pack cool down before charging it. - Charge the battery pack in temperatures between 0 °C and 40 °C (32 °F and 104 °F). - The battery pack is damaged. Use a different battery pack.
Sound is distorted or is recorded at lower levels. - When recording near loud sounds (such as fireworks, shows or concerts), sound may become distorted or it may not be recorded at the actual levels. Activate the microphone attenuator (0 153) or adjust the audio recording level manually (0 80). The picture is displayed correctly but there is no sound from the built-in speaker. - Speaker volume is turned off. Adjust the volume.
Connections with External Devices Video noise appears on the TV screen. - When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and the power or antenna cables of the TV. Playback looks fine on the camcorder but there is no image on the TV screen. - The video input on the TV is not set to the video terminal to which you connected the camcorder. Select the correct video input. There is no sound from the TV.
After connecting the camcorder to a printer, the message [Busy] continues to appear on the screen - Disconnect the USB cable and restore the connection after a short while. Photos are not correctly printed - You may not be able to print correctly, using a PictBridge-compatible printer, photos whose file names have been changed or that were recorded, created, edited or changed using another device.
e Built-in memory is full - The built-in memory is full (“f End” appears on the screen). Delete some recordings (0 56, 102) to free some space. Save your recordings (0 128) and initialize the built-in memory (0 40). e Cannot access the built-in memory - There is a problem with the built-in memory. Contact a Canon Service Center. Cannot communicate with the battery pack. Continue using this battery pack? - You attached a battery pack that is not recommended by Canon for use with this camcorder.
e Cannot play back Cannot access the built-in memory - There is a problem with the built-in memory. Save your recordings (0 128) and initialize the built-in memory using the [Complete Initialization] option (0 40). If the problem persists, contact a Canon Service Center. Cannot play back Check the memory card - There is a problem with the memory card. Save your recordings (0 128) and initialize the memory card using the [Complete Initialization] option (0 40).
Change the battery pack - Battery pack is exhausted. Replace or charge the battery pack. Check the memory card - Cannot access the memory card. Check the memory card and make sure it is inserted correctly. - A memory card error occurred. The camcorder cannot record or display the image. Try removing and reinserting the memory card, or use a different memory card. - You inserted a MultiMedia Card (MMC) into the camcorder. Use a recommended memory card (0 37).
Error writing on the memory card. Data may be recovered if the memory card has not been removed. Attempt recovering the data? - This message will appear the next time you turn on the camcorder if power supply was accidentally interrupted while the camcorder was writing on the memory card. Select [Yes] to try to recover the recordings. If you removed the memory card and used it with another device after this happened, we recommend you select [No].
Need to recover files from the memory card. Change the position of the LOCK switch on the memory card. - This message will appear the next time you turn on the camcorder if power supply was accidentally interrupted while the camcorder was writing on the memory card and later the position of the card's LOCK switch was changed to prevent erasure. Change the position of the LOCK switch. No faces were detected in this scene - The camcorder did not detect any faces in the scene displayed.
Some B photos could not be deleted - Protected photos (B) cannot be deleted. Remove the protection (0 115). Some scenes could not be added to the playlist. - You may not be able to add to the playlist scenes recorded using another device. - The playlist can contain a maximum of 999 scenes. If the playlist includes scenes recorded in MXP or FXP mode, the maximum number of scenes in the playlist may be less than 999. Delete some scenes from the playlist (0 95).
To record video on this memory card, it is recommended to use only the XP+/SP/LP recording modes - Movies may not be recorded correctly on this memory card if the recording mode is set to MXP or FXP mode (0 59). To use this function change the camcorder's mode from 5 to y - You pressed a button that cannot be used in mode. Set the mode switch to y to set the camcorder to flexible recording mode. Too many photos. Disconnect the USB cable. - Disconnect the USB cable.
Connect the compact power adapter - The camcorder is being powered by the battery pack. Connect the compact power adapter to the camcorder. Disc access failure. Check the disc. - There was an error when reading the disc or attempting to write onto it. - This message can appear also if condensation has formed (0 191). Wait until the DVD burner dries completely before resuming use. - The disc may be dirty or not correctly loaded.
File error - You attempted to print a photo that was recorded with another camcorder, has a different compression, or was edited on a computer. Hardware error - Cancel printing. Turn off the printer and turn it back on. - Check the printer status. - Ink tank errors have occurred. Replace the ink tank. Ink absorber full - Touch [Continue] to resume printing. Consult a Canon Service Center (refer to the list included with the printer) to replace the ink absorber.
Printer in use - The printer is in use. Check the printer status. Printing error - The printer does not support the paper size selected for [Paper Settings]. Set [Paper Settings] to [Default] or a paper size supported by the printer used. - Cancel printing, disconnect the USB cable and turn off the printer. After a while, turn the printer back on and reconnect the USB cable. Check the printer status.
Do’s and Don’ts Handling Precautions Camcorder Be sure to observe the following precautions to ensure maximum performance. • Save your recordings periodically. Make sure to transfer your recordings to an external device such as a computer or digital video recorder (0 126) and save them on a regular basis. This will protect your important recordings in case of damage and create more free space on the memory. Canon shall not be liable for any data loss. • Do not carry the camcorder by the LCD panel.
• When mounting the camcorder on a 5.5 mm tripod, make sure that the tripod's fastening screw is shorter than 5.5 mm (0.2 in.). Using other tripods may damage the camcorder. • When recording movies, try to get a calm, stable picture. Excessive camcorder movement while shooting and extensive use of fast zooms and panning can result in jittery scenes. In extreme cases, the playback of such scenes may result in visually induced motion sickness.
Remaining battery time If the remaining battery time displayed is not correct, charge the battery pack fully. Still, the correct time may not be displayed if a fully charged battery pack is used continuously in high temperatures or it is left unused for long periods of time. Also, the correct remaining time may not be displayed, depending on the battery life. Use the time shown on the screen as an approximation.
• Secure Digital (SD) memory cards have a physical switch to prevent writing on the card so as to avoid the accidental erasure of the card's content. To write-protect the memory card set the switch to the LOCK position. LOCK switch Built-in Rechargeable Lithium Battery The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings.
• Wipe the battery with a clean dry cloth to ensure proper contact. • For California, USA only: The lithium battery included contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for details. Disposal When you delete movies or initialize the memory, only the file allocation table is altered and stored data is not physically erased.
Maintenance/Others Cleaning Camcorder Body • Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents such as paint thinner. Lens and Instant AF Sensor • If the lens surface or Instant AF sensor is dirty, autofocus may not work properly. • Remove any dust or dirt particles using a non-aerosol type blower brush. • Use a clean, soft lens-cleaning cloth to gently wipe the lens. Never use tissue paper.
• Remove the memory card and battery pack. Then, place the camcorder in an airtight plastic bag and let it adjust gradually to temperature changes before removing it from the bag. When condensation is detected The camcorder automatically shuts off. The precise time required for water droplets to evaporate will vary depending on the location and weather conditions. As a general rule, wait for 2 hours before resuming use of the camcorder.
General Information Accessories (Availability differs from area to area) AVCHD discs/ Photo DVDs D PictBridgecompatible printers Card reader/writer Computer TV/HDTV VCR/DVD recorder Optional accessories not listed below are described in more detail in the following pages.
NOTES • Accessories that are compatible with the Advanced Accessory Shoe cannot be attached to this camcorder. Look for the Mini ADVANCED SHOE logo to ensure compatibility with the mini advanced shoe. Optional Accessories Call or visit your local retailer/dealer for genuine Canon video accessories. You can also obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040, Canon U.S.A. Information Center. Use of genuine Canon accessories is recommended.
5 CG-800 Battery Charger Use the battery charger to charge the battery packs. It plugs directly into a power outlet without a cable. Charging Times The charging times given in the following table are approximate and vary according to charging conditions and initial charge of the battery pack. Battery pack→ Charging conditions↓ BP-808 BP-809 BP-819 BP-827 Using the camcorder 150 min. 260 min. 385 min. Using the CG-800 Battery Charger 105 min. 190 min. 260 min.
Using a memory card Battery pack BP-808 BP-809 Usage time Recording mode MXP FXP XP+ SP LP Recording (maximum) 95 min. 95 min. 100 min. 100 min. 105 min. Recording (typical)* 60 min. 60 min. Playback 160 min. 160 min. 160 min. 165 min. 165 min. 65 min. 65 min. 65 min. Recording (maximum) 200 min. 200 min. 205 min. 205 min. 205 min. BP-819 Recording (typical)* 125 min. 130 min. 135 min. 135 min. 135 min. Playback 315 min. 320 min. 325 min. 330 min. 330 min. Recording (maximum) 300 min.
A FS-H37U Filter Set q Neutral density and MC protector filters help you to control difficult lighting conditions. A SC-2000 Soft Carrying Case a A handy camcorder bag with padded compartments and plenty of space for accessories. A SM-V1 Surround Microphone s Use 5.1ch surround sound to add a sense of presence to your movies. You can link the surround sound to the zoom position or use the microphone as a highly directional shotgun microphone (monaural).
A VFL-2 Video Flash Light g This video flash light allows you to record photos and movies even at night or in dark places. It attaches to the camcorder’s mini advanced shoe for cablefree operation. A RA-V1 Remote Control Adapter h Attaching this adapter to the mini advanced shoe allows you to use the optional ZR-2000 or ZR-1000 Zoom Remote Controller, which is useful when operating the camcorder while it is mounted on a tripod.
Product Codes Provided Accessories CA-570 Compact Power Adapter BP-808 Battery Pack WL-D89 Wireless Controller STV-250N Stereo Video Cable IFC-300PCU USB Cable 8468A002AA 2740B002AA D83-0790-000 3067A002AA (D82-0590-002) 6906A001AA Optional Accessories BP-809 Battery Pack 2588B003AA (silver), 2588B004AA (black) BP-819 Battery Pack 2589B002AA BP-827 Battery Pack 3185B002AA CG-800 Battery Charger 2590B002AA TL-H37 Tele-converter 8835A001AA WD-H37ll Wide-converter 3187B001AA FS-H37U Filter Set 8837A001AA VL
Specifications VIXIA HF M31 / VIXIA HF M30 / VIXIA HF M300 / System • Recording System Movies: AVCHD Video compression: MPEG-4 AVC/H.264; Audio compression: Dolby Digital 2ch; Dolby Digital 5.1ch* * Only when using the optional SM-V1 Surround Microphone. Photos: DCF (Design rule for Camera File system), compatible with Exif* Ver. 2.2 and with DPOF Image compression: JPEG (Super Fine, Fine, Normal) * This camcorder supports Exif 2.2 (also called “Exif Print”).
• Lens f=4.1-61.5 mm, F/1.8-3.2, 15x optical zoom 35 mm equivalent: Movies: [Dynamic] IS mode: 39.5 – 711 mm Other IS modes: 39.5 – 592.5 mm Photos: 39.5 – 592.5 mm • Lens Configuration: 11 elements in 9 groups (1 double-sided aspheric element) • AF System Autofocus (TTL + external distance sensor when set to [Instant AF]) or Manual focus • Filter Diameter: 37 mm • Minimum Focusing Distance 1 m (3.3 ft.); 1 cm (0.39 in.
Power/Others • Power supply (rated) 7.4 V DC (battery pack), 8.4 V DC (compact power adapter) • Power consumption: 3.5 W (SP mode, AF on, LCD normal brightness) • Operating temperature: 0 – 40 °C (32 – 104 °F) • Dimensions [W x H x D] (excluding the grip belt): 68 x 60 x 123 mm (2.7 x 2.4 x 4.8 in.) • Weight (camcorder body only): 320 g (11.3 oz.
About the music files The specifications of the music files compatible with the camcorder are as follows. Audio encoding: Linear PCM Audio sampling: 48 kHz, 16 bits, 2 channels Minimum length: 1 second File extension: WAV The music data is saved in the memory under the following folder structure. e In the built-in memory: CANON MY_MUSIC MUSIC_01.WAV to MUSIC_99.WAV On the memory card: CANON PRIVATE MY_MUSIC MUSIC_01.WAV to MUSIC_99.WAV Weight and dimensions are approximate. Errors and omissions excepted.
Index 24p Cinema Mode . . . . . . . . . . . . .63 3D Flip View . . . . . . . . . . . . . . . . .54 A Abroad, using the camcorder . . . .192 AF-assist lamp . . . . . . . . . . . . . .109 AGC (automatic gain) limit . . . . . . .74 Aperture (f number) . . . . . . . . . . . .70 Aspect ratio of a connected TV (TV type) . . . . . . . . . . . . . . . . . .157 Audio recording level . . . . . . . . . . .80 Auto exposure bracketing . . . . . .109 Auto slow shutter . . . . . . . . . . . .
Histogram . . . . . . . . . . . . . . . . . . 114 I Image effects . . . . . . . . . . . . . . . . 77 Image stabilizer . . . . . . . . . . . . . . . 64 Index screens . . . . . . . . . . . . . . . . 49 Index screen selection . . . . . . 52 Showing some/ all of the scenes . . . . . . . . . . 55 Initialization (built-in memory*/memory card) . . . . . . . . . . . . . . . . . . . . . 40 L Language . . . . . . . . . . . . . . . . . . . 36 LCD screen dimmer . . . . . . . . . . . 160 LCD touch screen . . . . . . .
Serial number . . . . . . . . . . . . . . . .22 Setup menus . . . . . . . . . . . . .33, 151 Shutter speed . . . . . . . . . . . . . . . .70 Simultaneous recording . . . . . . . . 110 Slideshow . . . . . . . . . . . . . . . . . . 112 Smart AUTO mode . . . . . . . . . . . .43 Snow (recording program) . . . . . . .61 Sports (recording program) . . . . . .61 Spotlight (recording program) . . . . .61 Sunset (recording program) . . . . . .61 Surface (recording program) . . . . . .62 T Telephoto . . . . . . . .
USA CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR THE UNITED STATES The limited warranty set forth below is given by Canon U.S.A., Inc. (“Canon USA”) with respect to Canon Consumer Digital Video Equipment (the “Equipment”) purchased in the United States. This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase.
LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENT’S HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CANADA CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY The limited warranty set forth below is given by Canon Canada Inc. (“Canon Canada”) with respect to Canon Consumer Digital Video Equipment (the “Equipment”) purchased in Canada. This limited warranty is only effective upon presentation of a bill of sale or other proof of purchase for this Equipment to a Canon Service Facility when repairs are required.
USA CANON U.S.A., INC. NEW JERSEY OFFICE 100 Jamesburg Road, Jamesburg, NJ 08831 USA CANON U.S.A., INC. CHICAGO OFFICE 100 Park Blvd., Itasca, IL 60143 USA CANON U.S.A., INC. LOS ANGELES OFFICE 15955 Alton Parkway, Irvine, CA 92618 USA CANON U.S.A., INC. HONOLULU OFFICE 210 Ward Avenue, Suite 200, Honolulu, Hl 96814 USA ❖ CANADA If you have any questions, call the Canon U.S.A. Information Center toll-free at 1-800-828-4040 (USA only). CANON CANADA INC.
