㻝㻌㻛㻌㻟㻠㻜
Consignes de sécurité importantes Installation Alimentation Manipulation Entretien et vérifications Consommables Fonctionnement de base Pièces et leur fonction Avant Face arrière Intérieur Fente d'alimentation manuelle Cassette à papier Panneau de commande Affichage Utilisation du panneau de commande Saisie du texte Placement des documents Chargement du papier Alimentation du papier dans la cassette à papier Chargement du papier dans la fente d'alimentation manuelle Chargement d'enveloppes Chargement du pap
Impression de plusieurs pages sur une seule feuille Impression de posters Impression des bordures Impression de la date et des numéros de pages Impression de filigranes Sélection du type de document Économie de l'encre Combinaison et impression de plusieurs documents Configuration des réglages d'impression en fonction de vos besoins Enregistrement de combinaisons de réglages d'impression couramment utilisés Modification des réglages par défaut Utilisation du service AirPrint (MF212w) Cryptage des communicat
Modification de l'unité de transmission maximale Définition d'un délai d'attente en vue de la connexion à un réseau Configuration de DNS Surveillance et contrôle de l'appareil via SNMP Sécurité Protection de l'appareil contre les intrusions Définition du PIN administrateur système Restriction des communications au moyen de pare-feu (MF212w) Spécification d'adresses IP pour les règles de pare-feu Spécification d'adresses MAC pour les règles de pare-feu Modification des numéros de port (MF212w) Réglage d'un p
Remplacement des cartouches de toner Avant de remplacer la cartouche de toner Comment remplacer les cartouches de toner Déplacement de l'appareil Affichage de la valeur du compteur Initialisation des réglages Initialisation du menu Initialisation des réglages de gestion du système Initialisation de toutes les données/tous les réglages Annexe Descriptions des fonctions Empreinte environnementale et maîtrise des coûts Gain de productivité Passage au numérique Nouvelles perspectives Caractéristiques Caractéris
0LW8-000 Consignes de sécurité importantes Le contenu décrit dans ce chapitre est destiné à prévenir les dommages aux biens et les blessures corporelles à l'encontre des utilisateurs de l'appareil ou d'autres personnes. Avant d'utiliser cet appareil, lisez attentivement ce chapitre et conformez-vous aux consignes d'utilisation de l'appareil. N'effectuez aucune opération qui ne soit pas décrite dans ce manuel.
0LW8-001 Installation Pour un confort d'utilisation et une utilisation sécurisée, lisez attentivement les précautions d'usage suivantes et installez l'appareil dans un lieu approprié.
Lieu mal ventilé Cet appareil émet une faible quantité d'ozone, notamment, en fonctionnement normal. Bien que la sensibilité à l'ozone et autres peut varier, la quantité dégagée n'est pas dangereuse. Vous remarquerez éventuellement la présence d'ozone ou d'autres gaz pendant une utilisation prolongée ou de longs cycles de production, notamment dans une pièce mal ventilée. Il est recommandé de prévoir une ventilation adéquate de la pièce afin de maintenir un environnement de travail confortable.
0LW8-002 Alimentation Cet appareil est compatible avec des tensions de 220 à 240 V et une fréquence électrique de 50/60 Hz. Utilisez exclusivement une alimentation électrique dont la tension correspond à celle indiquée. Sinon, vous risquez de provoquer des incendies ou de subir une électrocution. Utilisez uniquement le cordon d'alimentation fourni, pour éviter tout risque d'incendie ou d'électrocution.
0LW8-003 Manipulation Débranchez la fiche d'alimentation de la prise secteur et contactez un revendeur agréé Canon si l'appareil émet des bruits anormaux, de la fumée, de la chaleur ou une odeur inhabituelle. Si vous continuez à utiliser l'appareil, cela peut entraîner un risque d'incendie ou d'électrocution. Ne démontez jamais, ni n'altérez l'appareil. Il comporte des composants à haute tension et à haute température qui risquent de provoquer des incendies ou des électrocutions.
Informations relatives à la diode laser longueur d'onde : 785 à 800 nm puissance maximale : 6 mW Lorsque vous transportez l'appareil Pour éviter d'endommager l'appareil pendant le transport, procédez comme suit. Retirez les cartouches de toner. Rangez soigneusement l'appareil dans son carton d'origine avec tous les matériaux d'emballage. Autres précautions Suivez les instructions de l'étiquette d'avertissement fixée sur l'appareil. Evitez de secouer l'appareil ou de le soumettre à un choc.
0LW8-004 Entretien et vérifications Nettoyez régulièrement l'appareil. Si la poussière s'accumule, l'appareil ne fonctionnera pas correctement. Respectez les consignes de Dépannage. Si vous ne parvenez pas à résoudre le problème ou nettoyage suivantes. En cas de problème, reportez-vous à la section Lorsqu'un problème ne peut pas être résolu.
0LW8-005 Consommables Ne jetez pas les cartouches de toner usagées au feu. Ne stockez pas les cartouches de toner ou le papier dans un endroit exposé directement à une flamme nue. L'encre risque de s'enflammer, provoquant des brûlures ou un incendie. En cas de renversement accidentel de toner, rassembler avec précaution les particules de toner ou les enlever à l'aide d'un chiffon doux humide de façon à en éviter l'inhalation.
N'enlevez pas la cartouche de toner de cet appareil ou de son emballage de protection sans raison. La cartouche de toner est un produit magnétique. Conservez-la à distance des disquettes, lecteurs de disque et autres périphériques susceptibles d'être affectés par son magnétisme. Le non-respect de cette précaution peut entraîner la perte de données. Stockage de la cartouche de toner Conservez la cartouche dans les conditions suivantes pour garantir une utilisation sécurisée et satisfaisante.
0LW8-006 Fonctionnement de base Ce chapitre explique les opérations courantes, comme l'utilisation du panneau de commande ou le chargement du papier et des documents, régulièrement effectuées pour utiliser les fonctions de l'appareil. Pièces et leur fonction Cette section décrit les éléments extérieurs et intérieurs de la machine et leur fonction, ainsi que la manière d'utiliser les touches du Pièces et leur fonction panneau de commande et la façon de visualiser l'affichage.
Activation du mode de veille Cette section explique comment configurer le mode de veille. Activation du mode de veille Définition du délai de fermeture automatique Cette section explique comment activer le réglage .
0LW8-007 Pièces et leur fonction Cette section décrit les pièces de l'appareil (extérieur, avant et arrière, intérieur) et leur mode de fonctionnement. Outre la description des pièces de l'appareil utilisées pour les opérations de base comme le placement des documents, le chargement du papier et le remplacement des cartouches de toner, cette section décrit également les touches du panneau de commande et l'affichage. Lisez cette section pour en savoir plus sur les conseils d'utilisation de l'appareil.
0LW8-008 Avant Couvercle de la vitre d'exposition Ouvrez ce couvercle pour placer les documents contre la vitre d'exposition. Placement des documents Panneau de commande Le panneau de commande comprend diverses touches notamment des touches numériques et une touche [Départ], un écran et des indicateurs d'état. Il permet de réaliser toutes les opérations et de spécifier les réglages. Vous pouvez l'orienter vers le haut Panneau de commande Affichage ou le bas afin de faciliter son utilisation.
0LW8-009 Face arrière Plaque signalétique La plaque porte le numéro de série qui permet d'obtenir des renseignements sur l'appareil. être résolu Lorsqu'un problème ne peut pas Port USB Connectez un câble USB lorsque vous connectez l'appareil et un ordinateur. Pour connaître les étapes nécessaires à la connexion, reportez-vous à "Mise en route". Manuels inclus avec l'appareil Port LAN (MF212w) Connectez un câble réseau lorsque vous connectez l'appareil et routeur réseau local filaire, etc.
0LW8-00A Intérieur Panneau de commande Soulevez ce panneau pour remplacer les cartouches de toner ou éliminer les bourrages papier. Élimination de bourrages papier cartouches de toner Comment remplacer les Capot toner Ouvrez ce capot pour remplacer les cartouches de toner ou éliminer les bourrages papier. Élimination de bourrages papier de toner Guide de sortie du papier Ouvrez ce guide pour éliminer des bourrages papier.
0LW8-00C Fente d'alimentation manuelle Couvercle du chargeur manuel Ouvrez cette fente pour charger du papier dans la fente d'alimentation manuelle. Guides papier Ajustez les guides papier en fonction de la largeur du papier chargé pour s'assurer que le papier est bien dans l'axe de l'appareil.
0LW8-00E Cassette à papier Capot anti-poussière Ouvrez ce capot pour charger du papier dans la cassette à papier. Guides papier Ajustez les guides papier en fonction de la taille du papier chargé pour s'assurer que le papier est bien dans l'axe de l'appareil.
0LW8-00F Panneau de commande MF212w MF211 Touche [Menu] Appuyez sur cette touche pour commencer la définition de nombreux réglages de l'appareil comme ou . Liste des menus des réglages Touche [COPY/SCAN] Appuyez sur cette touche pour passer en mode de copie ou de numérisation. Touche [Copie carte ID] Appuyez sur cette touche pour accéder au mode permettant de copier en taille réelle le recto et le verso d'une carte d'identité ou d'un permis de conduire au recto d'une page.
Lors de la définition des réglages, utilisez cette touche pour passer à l'écran suivant. Lors de la saisie de texte, cette touche permet de déplacer le curseur vers la droite. Appuyez sur cette touche pour augmenter la valeur d'un réglage (la densité de la numérisation, de la copie, etc.). Touche [ ] Lors de la définition des réglages, cette touche permet de sélectionner un élément au-dessous de l'élément couramment sélectionné.
Touche [Menu] Appuyez sur cette touche pour commencer la définition de nombreux réglages de l'appareil comme ou . Liste des menus des réglages Touche [COPY/SCAN] Appuyez sur cette touche pour passer en mode de copie ou de numérisation. Touche [Copie carte ID] Appuyez sur cette touche pour accéder au mode permettant de copier en taille réelle le recto et le verso d'une carte d'identité ou d'un permis de conduire au recto d'une page.
Touche [Précédent] Utilisez cette touche pour revenir à l'écran précédent. Si vous appuyez sur cette touche lors de la définition des réglages, par exemple, les réglages ne seront pas appliqués et l'écran précédent s'affiche. Touche [OK] Appuyez sur la touche pour appliquer les réglages ou les détails spécifiés. Touche [Suivi statut] Appuyez sur cette touche pour vérifier le statut de l'impression ou de la copie ou pour consulter l'historique de l'appareil.
0LW8-00H Affichage L'affichage présente les écrans concernant la copie, la numérisation et d'autres fonctions, ainsi que les écrans destinés à définir les réglages de ces fonctions. Des informations telles que des messages d'erreur et des renseignements sur l'état des communications apparaissent également sur l'affichage. Ecran principal Lorsque vous appuyez sur (COPY/SCAN), l'écran principal de la fonction sélectionnée s'affiche. L'écran principal du mode de copie est illustré pour exemple ci-après.
Affiche les détails des éventuelles erreurs. Si un message d'erreur apparaît Affiche l'état de l'appareil tel que la quantité de papier ou d'encre encore disponible. Apparaît si chaque source de papier contient du papier. Affiche la quantité d'encre non consommée.
Si une erreur se produit Dans certains cas lorsqu'une erreur se produit, des consignes permettant de remédier à l'erreur s'affichent. Appliquez les instructions figurant à l'écran pour résoudre le problème. L'écran apparaissant en cas de bourrage papier est illustré ci-dessous à titre d'exemple ( Si un message d'erreur apparaît).
0LW8-00J Utilisation du panneau de commande Utilisez les touches illustrées ci-dessous pour définir les réglages et en ajuster la valeur. Avec / Défilement de l'écran La barre de défilement s'affiche à droite de l'écran lorsque toutes les informations ne tiennent pas dans un seul écran. Si la barre / pour faire défiler l'affichage vers le haut ou le bas. Les couleurs du texte et de l'arrière-plan de défilement apparaît, utilisez d'un élément sont inversées lorsqu'il est sélectionné.
Avec Appuyez sur pour appliquer un réglage. Avec les touches numériques Les touches numériques permettent de saisir du texte et des nombres. Saisie du texte Vous pouvez modifier un grand nombre de réglages relatifs à l'affichage tels que la vitesse de défilement ou la langue d'affichage. Pour en savoir plus à ce sujet. Réglages d'affichage Pour choisir un autre écran s'affichant automatiquement en cas d'inactivité de l'appareil pendant le laps de temps défini : Fonction après réinitialisation auto.
0LW8-00K Saisie du texte Utilisez les touches numériques pour saisir du texte et des valeurs. Changement du mode de saisie Appuyez sur pour passer à un autre mode de saisie de texte. La mention "A", "a" ou "12" indique le mode de saisie actuellement sélectionné dans . Vous pouvez également sélectionner et appuyez sur pour choisir un autre mode de saisie de texte.
Appuyez sur ou sélectionnez et appuyez sur lorsque le mode de saisie est ou pour afficher un / / / pour sélectionner le symbole à saisir et écran permettant de sélectionner les symboles. Utilisez les touches . appuyez sur Suppression de texte Un seul caractère est supprimé à chaque fois que vous appuyez sur l'ensemble du texte saisi. . Maintenez de la touche enfoncée pour supprimer Déplacement du curseur (saisie d'un espace) Appuyez sur ou pour déplacer le curseur.
0LW8-00L Placement des documents Placez des documents contre la vitre d'exposition. Pour plus d'informations sur les types de documents susceptibles d'être placés contre Type de document ou Zone de lecture. la vitre d'exposition et sur la zone numérisable d'un document, consultez la section Utilisez des documents qui ne présentent aucune humidité.
0LW8-00R Chargement du papier Vous pouvez charger du papier dans la cassette à papier ou la fente d'alimentation manuelle. Chargez le type de papier que vous employez d'habitude dans la cassette à papier, destinée à recevoir une grosse quantité de papier. Préférez la fente d'alimentation manuelle lorsque vous utilisez momentanément un format ou un type de papier différent de celui figurant dans la cassette à papier. Papier pour connaître les formats de papier disponibles.
outrance. Stockez le papier de façon à ce qu'il ne s'enroule pas, ni ne se replie. Ne conservez pas le papier à la verticale et n'empilez pas une trop grosse quantité de papier. Conservez le papier à l'abri des rayons directs du soleil, d'une humidité élevée, d'un air très sec ou de variations brusques de température ou d'humidité.
0LW8-00S Alimentation du papier dans la cassette à papier Vous chargez le papier couramment utilisé dans la cassette à papier. Pour imprimer sur un autre papier, chargez le papier dans la fente Chargement du papier dans la fente d'alimentation manuelle d'alimentation manuelle. Prenez soin de charger le papier en orientation portrait Le papier ne peut pas être chargé en orientation paysage, aussi veillez à charger le papier en orientation portrait. 1 Soulevez le capot anti-poussière.
Ne dépassez pas le guide de limite du papier lorsque vous chargez du papier Assurez-vous que la pile de papier se trouve sous le guide de limite du papier ( provoquer des bourrages papier. Pour charger des enveloppes ou du papier à en-tête, consultez la section papier à en-tête. 4 ). Un chargement excessif de papier risque de Chargement d'enveloppes ou Chargement du Alignez les guides papier sur les bords du papier.
Impression au verso d'une feuille imprimée (impression recto verso manuelle) Il est possible d'imprimer au verso d'une feuille déjà imprimée. Aplanissez le papier s'il s'enroule et insérez-le dans la fente d'alimentation manuelle ( Chargement du papier dans la fente d'alimentation manuelle), face à imprimer vers le haut (la face déjà imprimée est tournée vers le bas). Chargez une feuille à la fois pour chaque impression.
0LW8-00U Chargement du papier dans la fente d'alimentation manuelle Lorsque vous voulez imprimer sur un autre papier que celui qui se trouve dans la cassette à papier, chargez le papier dans la fente Alimentation du papier dans la d'alimentation manuelle. Vous chargez le papier couramment utilisé dans la cassette à papier.
Alignez les guides papier contre les bords du papier. Si le papier est trop serré ou, au contraire, pas assez fermement retenu par les guides papier, cela peut provoquer une alimentation incorrecte du papier ou des bourrages papier. 5 Sortez la butée du papier pour l'ouvrir.
0LW8-00W Chargement d'enveloppes Prenez soin de bien aplatir les enveloppes si nécessaire avant de les charger. Prêtez également attention à l'orientation des enveloppes et à la face qui est tournée vers le haut. Avant de charger les enveloppes Orientation du chargement Cette section indique comment charger les enveloppes dans l'orientation de votre choix et les procédures à suivre pour insérer les enveloppes.
Orientation du chargement Chargez les enveloppes en orientation portrait, avec le bord court vers l'avant, face non encollée (avant) vers le haut. Chargez les enveloppes en respectant la même orientation à la fois pour la cassette à papier et la fente d'alimentation manuelle. Chargez les enveloppes de façon à ce que leurs rabats se trouvent à gauche.
0LW8-00X Chargement du papier à en-tête Lorsque vous imprimez sur du papier à en-tête portant un logo, faites attention à l'orientation du papier au moment du chargement. Chargez le papier en veillant à imprimer sur la face du papier portant le logo. Impression sur un papier portant un logo préimprimé Cette section indique principalement comment charger du papier à en-tête selon la face à imprimer et l'orientation qui convient.
0LW8-00Y Spécification du format et du type de papier Vous devez définir les réglages relatifs au format et au type de papier de sorte qu'ils correspondant au papier chargé. Assurez-vous de bien modifier les réglages relatifs au papier lorsque vous chargez du papier d'un format différent de celui qui était chargé jusque-là. Si les réglages ne correspondent pas au format et au type de papier chargé, un bourrage papier ou une erreur d'impression peut avoir lieu.
3 Sélectionnez ou et appuyez sur 4 Sélectionnez un format de papier fréquemment utilisé et appuyez sur Les formats de papier non cochés apparaissent dans l'écran . 5 Sélectionnez et appuyez sur . LIENS Alimentation du papier dans la cassette à papier Papier 㻠㻢㻌㻛㻌㻟㻠㻜 . pour le cocher.
0LW8-010 Enregistrement d'un format de papier personnalisé Vous pouvez enregistrer un format de papier personnalisé fréquemment utilisé pour la cassette à papier et la fente d'alimentation manuelle respectivement. 1 2 Appuyez sur Utilisez / (Réglages papier). pour sélectionner ou et appuyez sur 3 Sélectionnez et appuyez sur 4 Indiquez le format du papier. 1 . Spécifiez la longueur de la dimension (la plus courte). Sélectionnez et appuyez sur .
LIENS Alimentation du papier dans la cassette à papier Chargement du papier dans la fente d'alimentation manuelle 㻠㻤㻌㻛㻌㻟㻠㻜
0LW8-011 Activation du mode silencieux Le Mode silence réduit le son produit par l'appareil en cours de fonctionnement. Si vous utilisez l'appareil la nuit, appuyez sur panneau de commande. Cette simple opération permet de réduire le son de l'appareil en cours de fonctionnement. Vous pouvez également spécifier une heure à partir de laquelle l'appareil passe automatiquement en Mode silence. sur le En Mode silence Lorsque l'appareil passe en Mode silence, s'allume en vert.
Désactivation du mode silencieux Appuyez sur pour désactiver le mode silencieux.
0LW8-012 Activation du mode de veille Le mode de veille permet de réduit la quantité d'énergie consommée par l'appareil en coupant le courant arrivant au panneau de commande. Si aucune opération n'est réalisée sur l'appareil pendant quelque temps (à la pause déjeuner, par exemple), vous pouvez au niveau du panneau de commande.
0LW8-013 Définition du délai de fermeture automatique En activant ce réglage, vous pouvez éteindre automatiquement l'appareil. L'appareil coupe l'alimentation au bout du temps d'inactivité défini en mode de veille. Vous réalisez ainsi des économies d'énergie la nuit et les jours non ouvrés si vous oubliez d'éteindre l'appareil.
0LW8-014 Copie Ce chapitre décrit les opérations de copie de base ainsi que différentes fonctions pratiques de copie de plusieurs pages sur une même feuille.
0LW8-015 Opérations de copie de base 1 Mettez le ou les documents en place. 2 Appuyez sur 3 Saisissez le nombre de copies à l'aide des touches du pavé numérique. Placement des documents (COPY/SCAN) pour passer à l'écran du mode de copie. Saisissez un nombre compris entre 1 et 99. Appuyez sur 4 Définissez les réglages de copie si nécessaire. Utilisez 5 pour annuler la quantité saisie. / Appuyez sur pour sélectionner les réglages. Divers réglages de copie . Le processus de copie commence.
Si le message <Écarts taille/réglages> s'affiche. Si un message d'erreur apparaît En cas de copie de documents dont le texte ou les images se prolongent jusqu'aux bords de la page La partie comprise dans les bords du document risque de ne pas être copiée. Pour plus d'informations sur les marges de Zone de lecture.
0LW8-016 Annulation de copies Si vous désirez annuler la copie immédiatement après avoir appuyé sur , sélectionnez ou appuyez sur sur le panneau de commande. Vous êtes également libre d'annuler la copie après avoir examiné le statut de la copie.
Annule la copie. Détails de la copie Le nombre de copies, les réglages ainsi que d'autres détails s'affichent. Si vous souhaitez examiner les détails sans annuler la copie, appuyez sur pour revenir à l'écran principal de copie.
0LW8-017 Divers réglages de copie De nombreux réglages sont disponibles et permettent de répondre à vos besoins comme économiser du papier ou faciliter la lecture de vos documents.
0LW8-018 Agrandissement ou réduction Vous agrandissez ou réduisez les copies en appliquant un taux de reproduction prédéfini, A4> par exemple, ou en définissent un taux de reproduction personnalisé par incréments de 1 %. (COPY/SCAN) Sélectionnez le taux de reproduction Utilisez / ou les touches du pavé numérique pour saisir le taux de reproduction et appuyez sur n'importe quel taux compris entre 25 % et 400 % par incréments de 1 %.
0LW8-019 Sélection du type de document Vous pouvez sélectionner la qualité d'image optimale de la copie selon le type de document (document texte, documents comportant des diagrammes ou des graphiques ou photos de magazine, par exemple). (COPY/SCAN) Sélectionnez le type de document Cette option convient lorsque vous copiez des documents qui ne contiennent que du texte.
0LW8-01A Réglage de la densité Vous pouvez ajuster la densité de la copie si le texte ou les images d'un document sont trop clairs ou trop foncés. Vous pouvez également régler automatiquement une densité optimale pour un document. (COPY/SCAN) Réglez la densité Une densité optimale pour le document est automatiquement réglée. est automatiquement défini sur . ( Sélection du type de document) Utilisez / pour ajuster la densité.
0LW8-01C Réglage de la netteté Vous pouvez ajuster la netteté de l'image copiée. Augmentez la netteté pour améliorer la netteté d'un texte flou ou de lignes floues et diminuez-la pour améliorer l'apparence de photos de magazine. (COPY/SCAN) Réglez la netteté <-> : appuyez sur Diminue la netteté ce qui donne une image plus douce. Exemple : vous voulez améliorer l'apparence de photos de magazine <+> : appuyez sur Augmente la netteté de l'image.
0LW8-01E Copie de plusieurs documents sur une seule feuille (2 sur 1 ; 4 sur 1) Vous pouvez copier deux ou quatre documents sur une même feuille à un format réduit. Cette fonction permet de diminuer le nombre de pages imprimées et donc de limiter la consommation de papier. L'utilisation de <2 sur 1>/<4 sur 1> réduit automatiquement le taux de reproduction (le taux s'affiche à l'écran).
0LW8-01F Utilisation de la touche [Paper Save Copy] Le fait d'appuyer sur active le réglage d'économie de papier. Plusieurs pages d'un document sont alors copiées sur une seule feuille de papier, ce qui permet d'économiser du papier. L'utilisation de réduit automatiquement le taux de reproduction (le taux s'affiche à l'écran).
0LW8-01H Copie des deux faces d'une carte d'identité sur une seule page Vous pouvez utiliser pour copier le recto et le verso d'une carte sur le recto d'une feuille de papier. Cette fonction est pratique pour copier une carte d'identité ou un permis de conduire. est compatible avec du papier A4/Lettre ou de format supérieur. est automatiquement défini sur <100%>.
0LW8-01J Tri séquentiel des copies par page Lorsque vous envisagez de réaliser plusieurs copies d'un document de plusieurs pages, réglez sur pour trier les copies dans l'ordre des pages. Ce mode est très utile pour préparer des documents à distribuer pour les réunions ou présentations. (COPY/SCAN) Les copies sont rassemblées par numéro de page et ne sont pas triées.
0LW8-01K Modification des réglages par défaut Les réglages par défaut désignent les réglages qui s'affichent lorsque vous allumez l'appareil ou appuyez sur . Modifier les réglages par défaut pour les adapter aux opérations que vous réalisez régulièrement vous évite de devoir configurer ces mêmes réglages chaque fois que vous réalisez des copies.
0LW8-01L Utilisation de l'appareil en tant qu'imprimante Il existe de nombreuses façons d'utiliser l'appareil en tant qu'imprimante. Vous pouvez imprimer les documents de votre ordinateur au moyen du pilote d'imprimante ou les documents des périphériques amovibles via AirPrint. Tirez pleinement parti des fonctions d'impression en fonction de vos besoins. Impression à partir d'un ordinateur Vous pouvez imprimer un document réalisé sur l'ordinateur par le biais du pilote d'imprimante.
0LW8-01R Impression à partir d'un ordinateur Vous pouvez imprimer un document traité dans une application de l'ordinateur par le biais du pilote d'imprimante. Le pilote d'imprimante compte des fonctions très utiles comme la fonction d'agrandissement/de réduction qui permet d'imprimer vos documents de diverses façons. Avant de recourir à cette fonction, vous devez néanmoins procéder à plusieurs opérations préalables comme l'installation du pilote d'imprimante sur l'ordinateur.
0LW8-01S Impression d'un document Cette section indique comment imprimer un document sur l'ordinateur à l'aide du pilote d'imprimante. 1 Ouvrez un document dans une application et affichez la boite de dialogue d'impression. La manière d'afficher la boite de dialogue varie d'une application à l'autre. Pour plus d'informations, consultez le mode d'emploi de l'application concernée. 2 Sélectionnez le pilote d'imprimante de l'appareil et cliquez sur [Préférences] (ou [Propriétés]).
Vous pouvez facilement spécifier la mise en page, la position de la reliure, etc. de façon intuitive sur l'aperçu. Pour plus d'informations, cliquez sur [Aide] dans l'écran du pilote d'imprimante. 4 Cliquez sur [Imprimer] (ou [OK]). L'impression démarre. Dans certaines applications, un écran similaire à celui illustré ci-dessous s'affiche. Pour annuler l'impression, cliquez sur [Annuler] lorsque l'écran illustré ci-dessus apparaît.
0LW8-01U Annulation des impressions Vous pouvez annuler l'impression de l'ordinateur ou sur le panneau de commande de l'appareil. À partir de l'ordinateur À partir du panneau de commande À partir de l'ordinateur Vous pouvez annuler l'impression à l'aide de l'icône de l'imprimante figurant dans la barre d'état système du bureau. 1 Double-cliquez sur l'icône de l'imprimante.
À partir du panneau de commande Annulez l'impression en appuyant sur Appuyez sur ou . pour Annuler Si une liste de documents apparaît à l'écran après l'activation de Sélectionnez le document à annuler. Sélectionnez la tâche à annuler Utilisez pour annuler Sélectionnez le document dans l'écran Plusieurs pages peuvent sortir malgré l'annulation de l'impression.
Vérification du statut d'impression 㻣㻠㻌㻛㻌㻟㻠㻜
0LW8-01W Vérification du statut d'impression Vous pouvez examiner les statuts d'impression en cours. Informations utiles dans les conditions suivantes Lorsque l'impression de vos documents est longuement différée, il peut être utile d'examiner la liste d'attente des documents à imprimer. Lorsque vous ne trouvez pas les documents que vous pensez avoir imprimés, recherchez si une erreur a eu lieu. 1 2 3 Appuyez sur Utilisez / .
0LW8-01X Divers réglages d'impression Il existe un large éventail de réglages visant à répondre à vos besoins, comme la fonction d'agrandissement/de réduction.
0LW8-01Y Agrandissement ou réduction Vous pouvez réaliser des impressions agrandies ou réduites en utilisant un taux d'impression prédéfini, tel que A5 ou A4, ou encore appliqué le taux d'impression de votre choix que vous définissez à 1 % près. Définition du taux d'impression en indiquant le format du document d'origine et le format du papier (taux prédéfini) Le taux d'impression se base automatiquement sur le format du document et le format du papier que vous avez indiqués.
Les réglages d'agrandissement/de réduction sur certaines applications ont la priorité sur ceux du pilote d'imprimante.
0LW8-020 Tri séquentiel des impressions par page Lorsque vous imprimez des copies d'un document de plusieurs pages, sélectionnez [Assembler] pour imprimer le document entier dans l'ordre des pages. Ce mode est très utile pour préparer des documents à distribuer pour les réunions ou présentations. Onglet [Paramètres de base] Sélectionnez [Assembler] ou [Grouper] pour [Finition] [OK] [Finition] Indiquez le mode de tri lorsque vous imprimez des documents de plusieurs pages.
0LW8-021 Impression de plusieurs pages sur une seule feuille Vous pouvez imprimer plusieurs pages sur une seule feuille. Ainsi, vous imprimez quatre ou neuf pages sur une seule feuille en utilisant [4 sur 1] ou [9 sur 1]. Utilisez cette fonction si vous voulez économiser du papier ou présenter votre document sous forme de vues miniatures.
0LW8-022 Impression de posters Vous pouvez imprimer un document d'une page sur plusieurs pages. Si, par exemple, vous voulez produire un document au format A4 neuf fois plus grand, vous obtiendrez une affiche de 3 feuilles sur 3 au format A4 après avoir imprimé le document et collez les feuilles ensemble.
0LW8-023 Impression des bordures Vous pouvez ajouter des bordures comme des lignes en pointillés ou des lignes doubles dans les marges des impressions. Onglet [Configuration page] [OK] Cliquez sur [Options de page] [Bordure] Sélectionnez le type de bordure qui vous intéresse. Aperçu Affiche un aperçu de la bordure sélectionnée.
0LW8-024 Impression de la date et des numéros de pages Vous êtes libre d'imprimer des informations comme la date ou les numéros de pages et d'indiquer l'endroit où insérer ces informations dans le document (en haut à gauche, en bas à droite, etc.). Onglet [Configuration page] Cliquez sur [Options de page] [OK] d'utilisateur ou du numéro des pages [OK] Sélectionnez l'emplacement de la date d'impression, du nom [Date d'impression] Indiquez l'endroit où vous voulez qu'apparaisse la date d'impression.
0LW8-025 Impression de filigranes Vous pouvez imprimer des filigranes tels que "COPIE" ou "CONFIDENTIEL" d'un bout à l'autre du document. Vous pouvez créer de nouveaux filigranes ou utiliser les filigranes pré-enregistrés. Onglet [Configuration page] Cochez la case [Filigrane] Sélectionnez un filigrane dans [Nom du filigrane] [OK] [Filigrane]/[Nom du filigrane] Cochez la case [Filigrane] pour afficher la liste des filigranes dans la liste déroulante [Nom du filigrane].
Impression d'un document Impression des bordures Impression de la date et des numéros de pages 㻤㻡㻌㻛㻌㻟㻠㻜
0LW8-026 Sélection du type de document Il est possible de définir le type de document afin d'obtenir une qualité d'image optimale. Il existe différents réglages pour les photos, les documents comportant des diagrammes ou des graphiques et les documents avec des dessins de conception contenant des lignes fines. Onglet [Qualité] Sélectionnez le type de document dans [Objectif] [OK] [Objectif] Sélectionnez une option adaptée au type de document ou à la finalité de l'impression.
0LW8-027 Économie de l'encre Vous pouvez définir le pilote d'imprimante afin d'imprimer les documents en utilisant moins d'encre. Lorsque le réglage d'économie d'encre est activé, les lignes fines et les parties dont la densité d'impression est plus claire peuvent être floues.
0LW8-028 Combinaison et impression de plusieurs documents Canon PageComposer permet de combiner plusieurs documents en une seule tâche d'impression et de l'imprimer conformément aux réglages d'impression sélectionnés. Cette fonction permet ainsi de combiner des documents issus de différentes applications et d'imprimer toutes les pages au même format de papier. 1 Ouvrez un document dans une application et affichez la boîte de dialogue d'impression.
5 Recommencez les étapes 1 à 4 pour les documents à combiner. Les documents sont ajoutés à Canon PageComposer. 6 Dans la liste [Nom du document], sélectionnez les documents à combiner et cliquez sur . Pour sélectionner plusieurs documents à la fois, cliquez sur les documents tout en maintenant enfoncé la touche [MAJ] ou touche [CTRL]. 7 Modifiez les réglages si nécessaire et cliquez sur [Combiner]. Les documents sélectionnés à l'étape 6 sont combinés.
Pour plus d'informations, cliquez sur [Aide] dans l'écran de la fonction Canon PageComposer. [Détails] Affiche l'écran des paramètres d'impression du pilote d'imprimante. Moins de réglages sont disponibles par rapport à la méthode d'impression habituelle. 8 Dans la liste [Nom du document], sélectionnez la tâche d'impression combinant les documents et cliquez sur . L'impression commence.
0LW8-029 Configuration des réglages d'impression en fonction de vos besoins Il est possible d'enregistrer les combinaisons de réglages sous forme de "profils" pour répondre à tous vos besoins en matière d'impression. Vous pouvez également enregistrer les réglages que vous utilisez couramment comme réglages par défaut.
0LW8-02A Enregistrement de combinaisons de réglages d'impression couramment utilisés Il peut être fastidieux de définir une combinaison de réglages telle que "orientation paysage sur papier A4 en mode Economie de toner" chaque fois que vous imprimez. Si vous enregistrez les combinaisons de réglages d'impression que vous appliquez régulièrement sous forme de "profils", vous pouvez alors spécifier les réglages d'impression en choisissant simplement le profil adapté dans la liste.
Modification des réglages d'un profil actuellement sélectionné Vous pouvez modifier les réglages d'un profil actuellement sélectionné. Il est également possible de créer un nouveau profil avec les réglages modifiés.
0LW8-02C Modification des réglages par défaut Les réglages par défaut représentent les réglages que vous voyez lorsque vous accédez à l'écran des réglages d'impression du pilote d'imprimante. Vous pouvez remplacer ces réglages par ceux que vous utilisez le plus couramment. Si, par exemple, vous voulez toujours imprimer 2 pages de documents sur une page, définissez [2 sur 1] comme réglages de disposition des pages par défaut.
0LW8-02E Utilisation du service AirPrint Il n'est pas forcément obligatoire de disposer d'un ordinateur pour imprimer des photos, des e-mails, des pages Web et d'autres documents. AirPrint permet d'imprimer en Wi-Fi à partir des périphériques Apple tels qu'un iPad, un iPhone, un iPod touch ou un Macintosh et ce, sans faire appel au pilote d'imprimante.
Nombre de copies Appuyez sur [+] ou [-] à droite de [1 copie] pour définir le nombre de copies. [Plage] Appuyez sur [Plage] et [Toutes les pages] ou définissez la plage des pages à imprimer lors de l'impression d'un document de plusieurs pages. Les réglages disponibles dans [Options d'imprimante] dépendent de l'application utilisée. Les formats de papier disponibles varient d'une application à l'autre. 6 Appuyez sur [Imprimer]. L'impression commence.
Annulation à partir de l'iPad, l'iPhone ou l'iPod touch 1 2 3 Appuyez à deux reprises sur [Principal]. Appuyez sur [Impression] pour afficher la liste des documents à imprimer. Appuyez sur le document dont vous voulez annuler l'impression et appuyez sur [Annuler l'impression]. Annulation sur Macintosh 1 2 3 Cliquez sur l'icône de votre imprimante qui s'affiche dans le Dock du bureau. Cliquez sur le document qui vous intéresse. Cliquez sur [Supprimer].
4 Cliquez sur [Modifier...]. 5 Spécifiez les réglages requis et cliquez sur [OK]. [Utiliser AirPrint] Cochez la case pour activer l'impression avec AirPrint. Pour désactiver cette fonction, désactivez la case correspondante. [Nom de l'imprimante]/[Emplacement]/[Latitude]/[Longitude] Saisissez le nom et l'emplacement de l'installation permettant d'identifier l'appareil à partir du périphérique Apple que vous utilisez.
Vous pouvez afficher l'écran pour AirPrint dans lequel vous avez accès non seulement aux réglages AirPrint, mais aussi aux informations sur les consommables tels que le papier et le toner. 1 2 3 4 Cliquez sur [Préférences Système] dans le Dock du bureau [Imprimantes et scanners]. Sélectionnez votre imprimante et cliquez sur [Options et fournitures]. Cliquez sur [Afficher la page web de l'imprimante]. Connectez-vous à l'interface utilisateur distante en mode Administrateur système.
0LW8-02F Cryptage des communications des données d'impression des périphériques Apple avec la méthode TLS Des attaques malveillantes de tierces parties par reniflement, usurpation d'identité et manipulation des données transitant par le réseau peuvent provoquer des pertes d'informations inattendues.
Affichage des détails d'un certificat Vous pouvez vérifier les détails d'un certificat ou le vérifier en cliquant sur le lien correspondant sous [Nom de clé], ou sur l'icône Vérification des paires de clés et des certificats numériques du certificat. 6 Activez TLS pour l'interface utilisateur distante. 1 Cliquez sur [Réglages réseau] 2 Cliquez sur [Modifier...]. 3 Cochez la case [Utiliser TLS], définissez les éléments requis et cliquez sur [OK]. [Réglages de sécurité d'AirPrint].
LIENS Utilisation du service AirPrint (MF212w) Génération de paires de clés Utilisation de paires de clés et de certificats numériques émis par une autorité de certification 㻝㻜㻞㻌㻛㻌㻟㻠㻜
0LW8-02H Configuration des paires de clés et des certificats numériques Pour crypter les communications échangées avec un appareil à distance, une clé de cryptage doit préalablement être envoyée et reçue via un réseau non sécurisé. Ce problème est résolu par une cryptographie de clé publique.
0LW8-02J Génération de paires de clés Il est possible de générer une paire de clés sur l'appareil lorsqu'elle est nécessaire à une communication cryptée via TLS (Transport Layer Security). Vous pouvez faire appel à TLS lors de l'accès à l'appareil depuis un périphérique Apple pour utiliser AirPrint. Vous pouvez Générer une clé et une enregistrer jusqu'à trois paires de clés sur l'appareil.
5 Sélectionnez [Communication réseau] et cliquez sur [OK]. 6 Spécifiez les réglages de la clé et du certificat. [Réglages de clé] [Nom de clé] Donnez un nom à la paire de clés (24 caractères alphanumériques maximum). Pensez à choisir un nom facile à identifier dans une liste par la suite. [Algorithme de signature] Sélectionnez l'algorithme de signature dans la liste déroulante. [Algorithme de clé] RSA sert à la génération d'une paire de clés. Sélectionnez la longueur de clé dans la liste déroulante.
La génération de clés de communication réseau peut prendre entre 10 et 15 minutes. Une fois la paire de clés générée, elle est automatiquement enregistrée sur l'appareil. Générer une clé et une demande de signature de certificat (CSR) 1 Lancez l'interface utilisateur distante en mode Administrateur système. 2 Cliquez sur [Réglages/Enregistrement]. 3 Cliquez sur [Réglages de sécurité] 4 Cliquez sur [Créer clé...]. Démarrage de l'interface utilisateur distante [Réglages clé et certificat].
6 Spécifiez les réglages de la clé et du certificat. [Réglages de clé] [Nom de clé] Donnez un nom à la paire de clés (24 caractères alphanumériques maximum). Pensez à choisir un nom facile à identifier dans une liste par la suite. [Algorithme de signature] Sélectionnez l'algorithme de signature dans la liste déroulante. [Algorithme de clé] RSA sert à la génération d'une paire de clés. Sélectionnez la longueur de clé dans la liste déroulante.
Si une fenêtre de confirmation apparaît, cliquez sur [Enregistrer] pour enregistrer le fichier. 9 10 Cliquez sur [Mémoriser le certificat...]. Cliquez sur [Choisir le fichier], spécifiez le fichier associé à la demande de signature de certificat et cliquez sur [Mémoriser].
0LW8-02K Utilisation de paires de clés et de certificats numériques émis par une autorité de certification Vous pouvez obtenir les paires de clés et les certificats numériques auprès d'une autorité de certification (CA) en vue de les utiliser sur l'appareil. Vous pouvez stocker, puis enregistrer ces fichiers via l'interface utilisateur distante. Assurez-vous que la paire de clés et le certificat répondent aux conditions requises pour l'appareil ( Configuration requise pour les clés et les certificats).
"TLS" s'affiche pour une paire de clés en cours d'utilisation auquel cas celle-ci ne peut être supprimée. Dans ce cas, désactivez la fonction ou remplacez la paire de clés avant de la supprimer. Désactivation ou activation des certificats CA préinstallés Cliquez sur [Désactiver] à droite du certificat CA pré-installé à désactiver. Pour réactiver le certificat, cliquez sur [Activer] à droite du certificat. 5 Cliquez sur [Installer...].
LIENS Génération de paires de clés Vérification des paires de clés et des certificats numériques Cryptage des communications des données d'impression des périphériques Apple avec la méthode TLS 㻝㻝㻝㻌㻛㻌㻟㻠㻜
0LW8-02L Vérification des paires de clés et des certificats numériques Une fois les paires de clés et les certificats CA enregistrés, vous pouvez afficher des informations détaillées à leur sujet ou contrôler leur validité ou leur signature. 1 Lancez l'interface utilisateur distante en mode Administrateur système. 2 Cliquez sur [Réglages/Enregistrement].
Le résultat de la vérification se présente comme suit.
0LW8-02R Utilisation de l'appareil en tant que scanner Il est possible de numériser des documents à partir du panneau de commande de l'appareil ou d'une application sur l'ordinateur. Quelle que soit la méthode choisie, les documents sont convertis en fichiers électroniques grâce à des formats comme le format PDF. Vous pouvez utiliser la numérisation pour convertir des documents papier très longs sous forme de fichiers électroniques et les gérer plus facilement.
0LW8-02S Préparation en vue de l'utilisation de l'appareil en tant que scanner Assurez-vous que l'appareil et l'ordinateur sont correctement reliés et que le logiciel est installé. Pour obtenir des informations sur la façon de procéder à cette vérification, reportez-vous à "Mise en route" ( Manuels inclus avec l'appareil). Pour établir la connexion via un réseau local filaire ou sans fil, vous devez enregistrer l'appareil auprès de la MF Network Scan Utility. Conformez-vous à la procédure suivante.
0LW8-02U Numérisation à partir de l'appareil La procédure visant à "numériser un document et à l'enregistrer sur un ordinateur" ne peut être réalisée que lorsque vous numérisez un document à partir de l'appareil. Lors de la numérisation, vous indiquez l'ordinateur sur lequel les documents seront enregistrés, vous spécifiez si vous numérisez les documents en couleur ou en noir et blanc, vous signalez le format dans lequel vous enregistrez les documents (PDF ou JPEG) ainsi que d'autres paramètres.
Vous pouvez modifier les réglages à partir de MF Toolbox. 6 Appuyez sur Configuration des réglages de numérisation dans MF Toolbox . La numérisation commence. Pour annuler, appuyez sur . Vous ne pouvez pas numériser tant que l'écran de configuration de MF Toolbox est affiché. Fermez l'écran avant de lancer la numérisation. 7 Si d'autres pages du document doivent être numérisées, placez la page suivante contre la vitre d'exposition et appuyez sur .
0LW8-02W Numérisation à l'aide de la touche [Scan -> PC] Placez un document sur l'appareil et appuyez sur ou (pour le modèle MF211, ) : la numérisation commence instantanément. Le type de numérisation (couleur ou noir et blanc), le dossier de destination du document et d'autres paramètres peuvent être enregistrés sur une touche. Les documents sont alors numérisés selon ces paramètres.
Sélectionnez ce réglage pour effacer les réglages enregistrés. Sélectionnez ce réglage si l'appareil et l'ordinateur ne sont pas connectés via USB. (MF212w) Sélectionnez ce réglage si l'appareil et l'ordinateur ne sont pas connectés via un réseau. 6 Sélectionnez l'ordinateur de destination et appuyez sur . Cet écran n'apparaît pas si vous sélectionnez à l'étape 5.
Utilisation de la touche [Scan -> PC] 1 Mettez le ou les documents en place. 2 Appuyez sur ou Placement des documents (pour le modèle MF211, appuyez sur ). Pour vérifier la configuration enregistrée pour la touche, reportez-vous à la section enregistrée. Vérification de la configuration La numérisation commence. Pour annuler, appuyez sur . Vous ne pouvez pas numériser tant que l'écran de configuration de MF Toolbox est affiché. Fermez l'écran avant de lancer la numérisation.
0LW8-02X Numérisation à partir d'un ordinateur Il existe deux façons de numériser un document à partir d'un ordinateur : utiliser MF Toolbox et utiliser une application de traitement de texte ou d'images. Numérisation à l'aide de MF Toolbox MF Toolbox est une application livrée avec l'appareil qui permet de numériser les documents à l'aide d'un ordinateur. Vous pouvez transférer les données numérisées vers l'application définie ou les joindre à un email.
0LW8-02Y Numérisation à l'aide de MF Toolbox Vous pouvez enregistrer des documents numérisés sur un ordinateur, les transférer vers l'application définie pour les modifier ou les joindre à un e-mail. MF Toolbox offre des réglages prédéfinis notamment pour la conversion au format PDF et la numérisation couleur. Vous pouvez facilement utiliser ces fonctions en sélectionnant un réglage prédéfini.
Pour choisir un autre scanner Si plusieurs appareils sont installés et que vous souhaitez utiliser un autre appareil, cliquez sur [Paramètres] et sélectionnez l'appareil de votre choix. Configuration des réglages pour MF Toolbox et le scanner 4 Configurez les réglages de numérisation comme souhaité. 5 Cliquez sur [Démarrer]. Configuration des réglages de numérisation dans MF Toolbox La numérisation commence. Pour annuler le processus de numérisation, cliquez sur [Annuler].
Configuration des réglages de numérisation en mode avancé Aperçu des images numérisées avant de définir le format de fichiers et d'enregistrer Il est possible d'afficher les images numérisées avant de définir le format de fichiers et d'enregistrer l'emplacement de destination. Cette procédure n'est pas disponible si [OCR] est sélectionné à l'étape 5. Mettez le document en place, lancez MF Toolbox et suivez la procédure décrite. 1 Sélectionnez le type de numérisation.
[Enregistrer sous le type] Sélectionnez un format de fichier comme PDF ou JPEG. Les formats disponibles varient selon le type de numérisation sélectionné à l'étape 1. Ajout de commentaires à un fichier JPEG Si vous sélectionnez [JPEG/Exif], vous pouvez ajouter des informations telles que la date ou les commentaires aux fichiers JPEG lorsque vous les enregistrez. Sélectionnez l'image numérisée, cliquez sur [Paramètres Exif] et saisissez vos commentaires dans l'écran qui s'affiche.
Cliquez sur [Paramètres PDF] et définissez comme bon vous semble les réglages de numérisation. des réglages de stockage 3 Configuration Cliquez sur [Parcourir] et sélectionnez le fichier PDF auquel vous voulez ajouter les pages. Les données du document qui vient d'être numérisé sont ajoutées au fichier PDF que vous sélectionnez. 4 Cliquez sur [Démarrer]. La numérisation commence. Pour annuler le processus de numérisation, cliquez sur [Annuler].
[Sélectionner un scanner] Sélectionnez le scanner (l'appareil) à utiliser avec MF Toolbox. [Nom de l'ordinateur] Lorsque vous numérisez un document à partir du panneau de commande de l'appareil, une procédure permet de désigner le dossier de destination du document numérisé ( Numérisation à partir de l'appareil). Il est possible de modifier le nom de l'ordinateur qui s'affiche à l'écran au cours de cette procédure. [Commentaire] Vous pouvez saisir un commentaire pour chaque type de numérisation.
0LW8-030 Configuration des réglages de numérisation dans MF Toolbox Vous pouvez modifier les réglages prédéfinis tels que le type de numérisation (couleur ou noir et blanc), le format de fichier et la résolution selon l'usage que vous voulez faire du document. Vous pouvez aussi désigner la destination du document numérisé, choisir une application comme application de transfert et configurer d'autres paramètres encore. Pour les utilisateurs Macintosh, les fonctions disponibles varient.
[Format papier] Sélectionnez le format du document. Si vous sélectionnez une option correspondant à un format personnalisé, la boîte de dialogue [Paramètres de format papier] s'ouvre. Vous êtes libre d'indiquer le format personnalisé de votre choix. [Mode de numérisation] Sélectionnez le type d'image choisi dans le cadre de la numérisation des documents. Les options disponibles varient selon le type de numérisation ([Message] ou [PDF], par exemple).
[Nom du fichier] Saisissez le nom du fichier de données numérisées. Si un fichier portant un nom identique existe déjà dans l'emplacement de l'enregistrement, un numéro unique à quatre chiffres (par exemple, "0001") est ajouté au nouveau nom de fichier. [Enregistrer sous le type] Sélectionnez le format de fichier. [BMP] Le document numérisé est converti sous forme d'une image. [JPEG/Exif] Le document numérisé est enregistré sous forme d'une image JPEG/Exif.
[Créer un PDF autorisant les recherches] Indiquez si vous voulez convertir le document numérisé en PDF autorisant les recherches. Les caractères du document numérisé sont convertis en données de texte, ce qui permet de lancer une recherche à partir d'un ordinateur. Le texte peut également être modifié à l'aide d'une application de traitement de texte. Pour créer un PDF autorisant les recherches, sélectionnez la valeur [300 ppp] pour [Qualité de l'image] ( Configuration des réglages de numérisation).
Becky! Ver.
0LW8-031 Numérisation à l'aide d'une application Numérisez les documents à l'aide d'une application. Vous pouvez utiliser Adobe Photoshop, Microsoft Office Word ou toute autre application de traitement de texte ou d'images. L'image numérisée est directement chargée dans l'application qui permet de modifier ou de traiter l'image immédiatement. La procédure suivante diffère selon l'application utilisée. L'application doit être compatible avec TWAIN ou WIA * .
0LW8-032 Configuration des réglages de numérisation dans ScanGear MF ScanGear MF est un pilote de scanner livré avec l'appareil. Vous pouvez utiliser ScanGear MF de la façon suivante. Démarrage à partir de MF Toolbox Lors de la numérisation via MF Toolbox, vous pouvez lancer ScanGear MF et configurer des réglages de numérisation avancés. Cochez Numérisation à l'aide la case [Afficher le pilote du scanner] et cliquez sur [Démarrer] dans MF Toolbox pour lancer ScanGear MF.
0LW8-033 Configuration des réglages de numérisation en mode simple Le mode simple est un ensemble de réglages de numérisation de base dans ScanGear MF conçu pour une plus grande facilité d'utilisation. En d'autres termes, le mode simple est une version condensée de ScanGear MF. Configurez les réglages dans l'ordre indiqué par les à sur l'écran et cliquez sur [Numériser]. Ce faisant, vous pouvez configurer les paramètres de base et la numérisation.
[Imprimer (300 ppp)] Sélectionnez ce réglage lorsque vous imprimez une image numérisée. [Affichage de l'image (150 ppp)] Sélectionnez cette option pour afficher l'image numérisée sur un ordinateur. [OCR (300 ppp)] Sélectionnez cette option pour utiliser l'image numérisée avec un logiciel de reconnaissance des caractères (OCR). [Format sortie] Sélectionnez le format de l'image numérisée pour l'afficher à l'écran ou l'imprimer.
0LW8-034 Configuration des réglages de numérisation en mode avancé Si vous cliquez sur l'onglet [Mode avancé] dans l'écran ScanGear MF, vous serez en mesure d'effectuer d'autres ajustements avancés de la qualité de l'image que ceux que vous réalisez en mode simple. Vous pouvez également enregistrer des réglages personnalisés sous figurant en regard. forme de réglages favoris.
(Zoom) Agrandit l'intégralité de l'aperçu. Cliquez avec le bouton gauche sur l'image pour effectuer un zoom avant et avec le bouton droit pour effectuer un zoom arrière. Pour agrandir une partie de l'image afin d'en examiner les détails, utilisez [Zoom] ( ). (Pivoter à gauche)/ (Pivoter à droite) Fait pivoter l'aperçu de 90 degrés vers la gauche ou vers la droite selon le cas. (Informations) Affiche les réglages actuels de l'image numérisée (le mode couleur et la taille de la zone de lecture).
Spécification de la résolution et de la taille de l'image Spécifiez la résolution ainsi que la taille de la sortie. [Résolution de sortie] Sélectionnez la résolution de l'image numérisée qui correspond le mieux à l'usage que vous souhaitez en faire. A propos de la résolution de la sortie Une résolution de 75 dpi est suffisante pour l'affichage d'une image numérisée sur un ordinateur tandis qu'une résolution de 300 dpi permet l'impression ou la création d'un fichier PDF autorisant les recherches.
[Tonalité automatique] Ajuste automatiquement la tonalité des couleurs de l'image. [Réduction des imperfections] Rend les imperfections du document moins apparentes. [Elevée] atténue les imperfections les plus importantes, mais risque de nuire aux détails de l'image. [Correction du ternissement] Le réglage est disponible si vous sélectionnez [Couleur] pour [Mode couleur]. Corrige les couleurs ternes du document ou améliore la saturation des documents aux couleurs ternes.
[Canal] Si vous sélectionnez [Couleur] pour [Mode couleur], vous pouvez ajuster séparément les canaux de couleur [Rouge], [Vert] et [Bleu]. Sélectionnez [Principal] pour régler les trois couleurs en même temps. Vous pouvez également combiner les réglages effectués pour [Principal] avec chacun des canaux de couleur. Si vous sélectionnez [Niveaux de gris] pour [Mode couleur], seul [Niveaux de gris] s'affiche. [Luminosité] Faites glisser ou saisissez une valeur. [Contraste] ou saisissez une valeur.
[Canal] Si vous sélectionnez [Couleur] pour [Mode couleur], vous pouvez ajuster séparément les canaux de couleur [Rouge], [Vert] et [Bleu]. Sélectionnez [Principal] pour régler les trois couleurs en même temps. Vous pouvez également combiner les réglages effectués pour [Principal] avec chacun des canaux de couleur. Si vous sélectionnez [Niveaux de gris] pour [Mode couleur], seul [Niveaux de gris] s'affiche.
Onglet [Aperçu] Configurez les opérations d'aperçu et de découpage automatique. [Aperçu au démarrage de ScanGear] Sélectionnez l'opération d'aperçu lorsque vous lancez ScanGear MF. [Exécuter automatiquement l'aperçu] La numérisation de l'aperçu démarre automatiquement lorsque vous lancez l'application ScanGear MF. [Afficher l'aperçu de l'image enregistrée] L'aperçu ne démarre pas automatiquement ; l'aperçu le plus récemment enregistré s'affiche.
réglages sont remplacés et les documents sont numérisés selon le mode couleur de ScanGear MF défini sur [Texte amélioré]. [Fermer automatiquement ScanGear après la numérisation] L'écran [ScanGear MF] se ferme automatiquement à l'issue de la numérisation. L'écran peut se fermer automatiquement pour certaines applications indépendamment de ce réglage.
Vous pouvez vérifier si la fonction de numérisation de l'appareil fonctionne correctement. Lorsque l'écran [Diagnostics du scanner] s'affiche, cliquez sur [Démarrer]. Enregistrement de réglages couramment utilisés Il peut être fastidieux de configurer le mode couleur, la qualité de l'image et d'autres réglages chaque fois que vous voulez numériser un document.
Rappel des réglages favoris enregistrés Affichez un aperçu et sélectionnez le réglage mémorisé dans la liste déroulante. Enregistrement des réglages de couleur ou de luminosité Pour enregistrer les réglages définissant la luminosité, le contraste, l'histogramme, la courbe de tonalité ou le seuil, suivez la procédure décrite ci-après. 1 2 Mettez le ou les documents en place et cliquez sur [Aperçu]. Ajustez la luminosité ou les couleurs.
LIENS Configuration des réglages de numérisation en mode simple Numérisation à l'aide de MF Toolbox Numérisation à l'aide d'une application 㻝㻠㻣㻌㻛㻌㻟㻠㻜
0LW8-035 Réseau Dès sa conception, cet appareil a été pensé pour prendre en compte la diversité des environnements ; il présente des technologies avancées en plus des fonctions réseau standard. Ne vous inquiétez pas si vous n'êtes pas un spécialiste des réseaux, car l'appareil se distingue également par son côté pratique et sa simplicité d'utilisation. Vous abordez simplement la configuration du réseau, étape après étape.
0LW8-036 Connexion à un réseau Lorsque vous connectez l'appareil à un réseau local filaire ou sans fil, vous devez attribuer une adresse IP unique au réseau sélectionné. Sélectionnez la mention "filaire" ou "sans fil" selon votre environnement de communication et vos périphériques réseau. Pour connaître les étapes nécessaires à la connexion de l'appareil et définir une adresse IP, reportez-vous à "Mise en route" ( Manuels inclus avec l'appareil).
Définissez l'adresse IP comme il convient. Cette étape est requise si vous voulez affecter une adresse IP donnée à l'appareil ou choisir un autre protocole d'adressage IP dynamique que le protocole DHCP défini par défaut.
0LW8-037 Sélection d'un réseau local sans fil ou filaire Après avoir déterminé si vous reliez l'appareil à l'ordinateur via un réseau local sans fil ou un réseau local filaire, sélectionnez le réseau en question à partir du panneau de commande. Pour obtenir des informations sur la connexion et spécifier les réglages d'un réseau local sans fil ou filaire, reportez-vous à "Mise en route" ( Manuels inclus avec l'appareil).
0LW8-038 Connexion à un réseau local filaire Connectez l'appareil à un ordinateur par un routeur. Utilisez un câble réseau pour relier l'appareil et le routeur. 1 Connectez un câble réseau. Connectez l'appareil à un routeur au moyen d'un câble réseau. Poussez le connecteur à fond ; vous devez entendre un déclic. 2 Patientez 2 minutes environ. Pendant ce temps, l'adresse IP est automatiquement définie. Vous pouvez définir vous-même l'adresse IP.
0LW8-039 Connexion à un réseau local sans fil Les routeurs sans fil (ou points d'accès) relient l'appareil et l'ordinateur au moyen d'ondes radio. Si votre routeur sans fil est équipé de la fonction WPS (Wi-Fi Protected Setup, installation Wi-Fi protégée), la configuration de votre réseau est simple et automatique.
Si le routeur sans fil est réglé sur l'authentification WEP, vous ne serez peut-être pas en mesure de configurer la connexion à l'aide de WPS. Configuration manuelle de la connexion Lorsque vous configurez une connexion sans fil, vous pouvez soit sélectionner un routeur sans fil, soit saisir manuellement les informations requises. Quelle que soit la méthode, assurez-vous de détenir les informations requises et notamment le SSID et la clé réseau ( Vérification du SSID et de la clé réseau).
0LW8-03A Configuration de la connexion à l'aide du mode bouton poussoir WPS Si votre routeur sans fil prend en charge le mode bouton poussoir WPS, vous configurez facilement une connexion avec le bouton WPS. Le fonctionnement du routeur sans fil dépend du périphérique utilisé. Pour obtenir de l'aide, reportez-vous au mode d'emploi fourni avec votre périphérique réseau. 1 2 Appuyez sur Utilisez / . pour sélectionner et appuyez sur .
Lorsque la configuration est terminée, l'écran ci-dessous s'affiche ; au bout de 2 secondes environ, le témoin Wi-Fi s'allume. Patientez pendant 2 minutes environ, le temps que les réglages d'adresse IP de l'appareil soient complètement définis. Force du signal Lorsque plusieurs routeurs sans fil sont disponibles pour la connexion, l'appareil se connecte au périphérique dont le signal radio est le plus puissant.
0LW8-03C Configuration de la connexion à l'aide du mode code PIN WPS Si le routeur sans fil prend en charge le mode code PIN WPS, générez un code PIN avec l'appareil et enregistrez le code sur le périphérique réseau. Le fonctionnement du routeur sans fil dépend du périphérique utilisé. Pour obtenir de l'aide, reportez-vous au mode d'emploi fourni avec votre périphérique réseau.
9 Vérifiez si le témoin Wi-Fi clignote sur le panneau de commande. Le témoin Wi-Fi clignote dès qu'un routeur sans fil a été détecté. Lorsque la configuration est terminée, l'écran ci-dessous s'affiche ; au bout de 2 secondes environ, le témoin Wi-Fi s'allume. Patientez pendant 2 minutes environ, le temps que les réglages d'adresse IP de l'appareil soient complètement définis.
0LW8-03E Configuration de la connexion par la sélection d'un routeur sans fil Vous pouvez rechercher les routeurs (ou points d'accès) de réseau sans fil disponibles pour la connexion et sélectionnez celui qui convient sur l'écran de l'appareil. En ce qui concerne la clé réseau, saisissez une clé WEP ou TKIP. Avant de sélectionner un routeur sans fil, vérifiez et notez les informations de configuration requises, en particulier le SSID et la clé réseau ( Vérification du SSID et de la clé réseau).
8 Indiquez la clé réseau à l'aide des touches numériques, sélectionnez , et appuyez sur Saisie du texte WPA-PSK ou WPA2-PSK WEP 9 . Sélectionnez et appuyez sur . Si un message d'erreur s'affiche au cours de la configuration Appuyez sur 10 , vérifiez si la clé réseau est correcte et retournez à l'étape 5. Vérifiez si le témoin Wi-Fi clignote sur le panneau de commande. Le témoin Wi-Fi clignote dès qu'un routeur sans fil a été détecté.
0LW8-03F Configuration de la connexion par la définition des réglages détaillés Si vous désirez définir les réglages de sécurité détaillés ou ne parvenez pas à établir la connexion sans fil par les autres méthodes, saisissez manuellement toutes les informations requises pour la connexion du réseau local sans fil.
4 Sélectionnez la clé WEP (1 à 4) à modifier et appuyez sur . Il est possible d'enregistrer jusqu'à quatre clés WEP. 5 Saisissez la clé réseau que vous avez notée. Indiquez la clé réseau à l'aide des touches numériques, sélectionnez , et appuyez sur Saisie du texte 6 Sélectionnez et appuyez sur 7 Sélectionnez la clé WEP que vous avez modifiée et appuyez sur . . .
Si un message d'erreur s'affiche au cours de la configuration Appuyez sur 9 , vérifiez si les réglages indiqués sont corrects et retournez à l'étape 5. Vérifiez si le témoin Wi-Fi clignote sur le panneau de commande. Le témoin Wi-Fi clignote dès qu'un routeur sans fil a été détecté. Lorsque la configuration est terminée, l'écran ci-dessous s'affiche ; au bout de 2 secondes environ, le témoin Wi-Fi s'allume.
0LW8-03H Vérification du SSID et de la clé réseau Lorsque vous configurez manuellement une connexion sans fil, vous devez indiquer le SSID et la clé réseau de votre routeur sans fil. Le SSID et la clé réseau peuvent être stipulées sur ces périphériques réseau. Vérifiez vos périphériques réseau et notez les informations nécessaires avant de configurer la connexion. Pour en savoir plus, reportez-vous aux modes d'emploi fournis avec vos périphériques réseau ou contactez les fabricants concernés.
4 Lisez attentivement le contrat de licence et cliquez sur [Yes] pour l'accepter. 5 Examinez les informations concernant le routeur sans fil. Notez par écrit les informations nécessaires. Si vous ignorez les informations requises, notez toutes les information affichées. Si les routeurs sans fil sont introuvables Cliquez sur [Refresh]. Si rien ne se passe, contrôlez que les réglages sont correctement définis sur l'ordinateur et le routeur sans fil.
0LW8-03J Définition des adresses IP Il convient de relier l'appareil à un réseau exigeant une adresse IP réseau unique. Deux versions d'adresses IP existent : IPv4 et IPv6. Configurez ces réglages en fonction de votre environnement réseau. Pour utiliser les adresses IPv6, vous devez configurer convenablement les réglages d'adresse IPv4.
0LW8-03K Définition de l'adresse IPv4 L'adresse IPv4 de l'appareil peut être attribuée automatiquement par un protocole d'adressage IP dynamique comme DHCP ou encore saisie manuellement. Lorsque vous reliez l'appareil à un réseau local filaire, assurezvous que les connecteurs du câble réseau sont bien insérés dans les ports ( Connexion à un réseau local filaire). Testez, si nécessaire, la connexion réseau.
4 Sélectionnez et appuyez sur . Les adresses IP affectées par les protocoles DHCP/BOOTP/RARP prévalent sur l'adresse obtenue par le réglage IP auto. Saisie manuelle d'une adresse IP 1 Vérifiez si est réglé sur . Si s'affiche, sélectionnez et définissez et sur .
0LW8-03L Définition des adresses IPv6 Les adresses IPv6 de l'appareil peuvent être configurées par l'interface utilisateur distante. Avant de configurer les adresses IPv6, examinez la définition de l'adresse IPv4 ( Affichage des réglages IPv4). Vous devez configurer convenablement les adresses IPv4 pour utiliser les adresses IPv6. Notez que la fonction de numérisation qui fait appel au pilote de scanner ou à MF Toolbox n'est pas disponible dans un environnement IPv6.
5 Cochez la case [Utiliser IPv6] et configurez les réglages appropriés. [Utiliser IPv6] Cochez la case pour activer IPv6 sur l'appareil. Si vous n'utilisez pas IPv6, désactivez cette case. [Adresse sans état] Cochez la case pour utiliser une adresse sans état. Si tel n'est pas le cas, désactivez cette case.
Assurez-vous que l'écran de l'interface utilisateur distante s'affiche sur votre ordinateur avant d'utiliser l'adresse IPv6 de Démarrage de l'interface utilisateur distante l'appareil. Utilisation du panneau de commande L'écran
0LW8-03R Affichage des réglages réseau Affichage des réglages IPv4 Affichage des réglages IPv6 Affichage de l'adresse MAC Affichage des réglages réseau sans fil et des informations L'adresse IP n'est pas correctement configurée si "0.0.0.0" s'affiche. Connecter l'appareil à un concentrateur de commutation peut entraîner l'échec de la connexion même si l'adresse IP est correctement configurée. Ce problème peut être résolu en retardant le démarrage des communications de l'appareil.
Affichage des réglages réseau sans fil et des informations 1 2 Appuyez sur Utilisez / . pour sélectionner et appuyez sur . Si un écran vous invitant à saisir un code PIN apparaît, saisissez le code PIN à l'aide des touches numériques et appuyez sur . Définition du PIN administrateur système 3 Sélectionnez et appuyez sur .
Configuration de DNS 㻝㻣㻠㻌㻛㻌㻟㻠㻜
0LW8-03S Configuration de l'appareil pour imprimer à partir d'un ordinateur Si vous utilisez l'appareil en guise d'imprimante réseau, vous pouvez configurer les protocoles et les ports destinés à l'impression et créer un serveur d'impression pour l'appareil. Avant de configurer l'appareil pour imprimer à partir d'un ordinateur, effectuez les procédures de configuration standard, notamment l'installation du pilote d'imprimante (Guide d'installation du pilote MF).
0LW8-03U Configuration des protocoles d'impression et des fonctions WSD Configurez les protocoles servant à imprimer des documents à partir d'un ordinateur relié au réseau. Les protocoles pris en charge par l'appareil incluent les protocoles LPD, RAW et WSD (Web Services on Devices). Pour modifier les numéros de port des protocoles, reportez-vous à la section Modification des numéros de port (MF212w). 1 Lancez l'interface utilisateur distante en mode Administrateur système.
[Utiliser impression LPD] Cochez la case pour imprimer via LPD. Si tel n'est pas le cas, désactivez cette case. [Utiliser impression RAW] Cochez la case pour imprimer via RAW. Si tel n'est pas le cas, désactivez cette case. 3 Cliquez sur [OK]. Configuration du protocole WSD 1 Cliquez sur [Modifier...] dans [Réglages WSD]. 2 Configurez les réglages comme il convient. [Utiliser impression WSD] Cochez la case pour imprimer via WSD. Si tel n'est pas le cas, désactivez cette case.
3 5 Cliquez sur [OK]. Redémarrez l'appareil. Éteignez l'appareil et attendez au moins 10 secondes avant de le rallumer. Utilisation du panneau de commande La touche
0LW8-03W Configuration des ports d'imprimante Les erreurs d'impression se produisent si l'adresse IP de l'appareil est modifiée ou si une imprimante est ajoutée dans le dossier des imprimantes de Windows. Ces erreurs sont généralement dues à une définition incorrecte des ports d'imprimante. C'est le cas, par exemple, lorsqu'un mauvais numéro ou type de port est défini. En pareille situation, la tentative d'impression se solde par un échec, car les données du document ne peuvent pas atteindre l'appareil.
3 Cliquez sur [Détection auto], sélectionnez l'appareil dès qu'il est détecté et cliquez sur [Suivant]. Si l'appareil n'est pas détecté Cliquez sur [Actualiser]. Si le problème persiste, cliquez sur [Adresse IP] ou [Adresse MAC], saisissez l'adresse IP ou MAC de l'appareil Affichage des réglages réseau, puis cliquez sur [Suivant]. 4 Cliquez sur [Ajouter] 5 Cliquez sur [Fermer]. [Finition].
LIENS Configuration du serveur d'impression 㻝㻤㻝㻌㻛㻌㻟㻠㻜
0LW8-03X Configuration du serveur d'impression Avec un serveur d'impression, il est possible de réduire la charge de travail de l'ordinateur à partir duquel vous imprimez. Le serveur d'impression permet également à chaque ordinateur d'installer les pilotes MF sur le réseau, ce qui vous évite de devoir installer les pilotes sur chaque ordinateur au moyen du DVD-ROM. Pour configurer un ordinateur sur le réseau en tant que serveur d'impression, définissez les réglages de manière à partager l'imprimante.
Cliquez sur [Modifier les options de partage]. Si la boîte de dialogue [Contrôle de compte d'utilisateur] s'affiche, cliquez sur [Oui] (ou sur [Continuer]). 4 Installez les pilotes supplémentaires nécessaires. Cette opération est indispensable pour installer les pilotes MF sur d'autres ordinateurs d'architecture différente via le serveur d'impression. 1 Cliquez sur [Pilotes supplémentaires].
Installation des pilotes MF sur un ordinateur via le serveur d'impression 1 2 3 Recherchez l'imprimante partagée sur le serveur d'impression. dans le serveur d'impression Double-cliquez sur l'imprimante partagée. Suivez la procédure décrite à l'écran pour installer les pilotes.
0LW8-03Y Configuration de l'appareil selon votre environnement réseau La configuration d'un réseau varie selon la finalité du réseau. Indiquez les réglages de façon à les adapter à votre environnement réseau.
0LW8-040 Configuration des réglages Ethernet Ethernet est une norme de transmission des données dans un réseau local. Vous définissez le mode de communication (semiduplex/duplex intégral) et le type Ethernet (10BASE-T/100BASE-TX). En général, il est possible de faire fonctionner l'appareil sans modifier les paramètres par défaut ( Réglages du pilote Ethernet). Cependant, vous pouvez les modifier afin de tenir compte des besoins de votre environnement réseau. 1 2 Appuyez sur Utilisez / .
Modification de l'unité de transmission maximale Définition d'un délai d'attente en vue de la connexion à un réseau 㻝㻤㻣㻌㻛㻌㻟㻠㻜
0LW8-041 Modification de l'unité de transmission maximale Dans la plupart des réseaux Ethernet, la taille maximale d'un paquet pouvant être envoyé est de 1 500 octets. Un paquet représente la portion des données selon laquelle les données d'origine sont divisées avant d'être envoyées. L'unité de transmission maximale (MTU) varie d'un réseau à l'autre. Modifiez les réglages de l'appareil au besoin. Pour plus d'informations, contactez votre administrateur réseau. 1 2 Appuyez sur Utilisez / .
0LW8-042 Définition d'un délai d'attente en vue de la connexion à un réseau Lorsqu'un réseau est conçu pour tirer parti de la connectivité redondante par le biais de plusieurs ponts ou concentrateurs de commutation, il doit posséder un mécanisme visant à empêcher les paquets de circuler en boucle. Une solution efficace consiste à définir le rôle de chacun des ports de commutation.
0LW8-043 Configuration de DNS Le service DNS (Domain Name System) assure un service de résolution des noms qui associe un hôte (ou domaine) à une adresse IP. Configurez les réglages DNS, mDNS ou DHCP comme il convient. Notez que les procédures visant à configurer DNS diffèrent selon les adresses IPv4 et IPv6. 1 Lancez l'interface utilisateur distante en mode Administrateur système. 2 Cliquez sur [Réglages/Enregistrement]. 3 Cliquez sur [Réglages réseau] 4 Configurez les réglages DNS.
[Réglages DNS] [Adresse serveur DNS primaire] Spécifiez l'adresse IP d'un serveur DNS. [Adresse serveur DNS secondaire] Spécifiez l'adresse IP d'un serveur DNS secondaire, le cas échéant. [Nom d'hôte] Saisissez le nom d'hôte de l'appareil (dans la limite de 47 caractères alphanumériques) qui est enregistré sur le serveur DNS. [Nom de domaine] Saisissez le nom de domaine (dans la limite de 47 caractères alphanumériques) auquel l'appareil appartient, tel que "exemple.com.
2 Configurez les réglages DNS IPv6. La case [Utiliser IPv6] doit être cochée pour configurer les réglages. Définition des adresses IPv6 [Réglages DNS] [Adresse serveur DNS primaire] Saisissez l'adresse IP d'un serveur DNS. Vous ne pouvez pas saisir d'adresses commençant par "ff" (ou adresses multidiffusion). [Adresse serveur DNS secondaire] Saisissez l'adresse IP d'un serveur DNS secondaire. Vous ne pouvez pas saisir d'adresses commençant par "ff" (ou adresses multidiffusion).
Utilisation du panneau de commande L'écran
0LW8-044 Surveillance et contrôle de l'appareil via SNMP Le protocole SNMP (Simple Network Management Protocol) est un protocole dédié à la surveillance et au contrôle des périphériques de communication d'un réseau et fait intervenir une base d'informations de gestion MIB (Management Information Base). L'appareil prend en charge la version SNMPv1. Vous pouvez vérifier le statut de l'appareil à partir d'un ordinateur lorsque vous imprimez des documents ou utilisez l'interface utilisateur distante.
5 Définissez les réglages SNMPv1. [Utiliser SNMPv1] Cochez la case pour activer SNMPv1. Vous ne pouvez spécifier les autres réglages SNMPv1 que si vous cochez cette case. [Utiliser le nom communautaire 1]/[Utiliser le nom communautaire 2] Cochez la case pour spécifier un nom de communauté. Sinon, désactivez-la. [Nom communautaire] Saisissez un nom de communauté de 32 caractères alphanumériques maximum.
Désactivez la case [Utiliser SNMPv1]. 6 Définissez les réglages d'acquisition des informations de gestion d'impression. Grâce à SNMP, un ordinateur relié au réseau permet de surveiller et d'obtenir régulièrement les informations de gestion d'impression, telles que les protocoles d'impression et les ports d'imprimante. [Acquérir les informations de gestion d'impression depuis l'hôte] Cochez la case pour activer la surveillance des informations de gestion d'impression de l'appareil via SNMP.
0LW8-045 Sécurité Des informations confidentielles transitent chaque jour par de multiples périphériques (ordinateurs, imprimantes ou autres). Or, ces périphériques peuvent être la cible d'attaques malveillantes. Les agresseurs peuvent s'introduire directement sur vos périphériques ou de façon indirecte en profitant d'une négligence ou d'un usage inadapté. Quel que soit le moyen utilisé, la fuite d'informations confidentielles peut être préjudiciable.
0LW8-046 Protection de l'appareil contre les intrusions Empêchez l'accès et l'utilisation de l'appareil par des personnes tierces non autorisées. Pour ce faire, pensez à mettre en œuvre les différentes mesures de sécurité à votre disposition (utilisation de pare-feu et modification des numéros de port).
0LW8-047 Définition du PIN administrateur système Définissez un PIN administrateur système réservé exclusivement aux administrateurs. Vous ne pourrez accéder aux , , etc. qu'à condition de saisir le PIN qui convient. Seuls les administrateurs doivent connaître ce PIN. 1 2 3 4 Appuyez sur Utilisez / . pour sélectionner et appuyez sur Sélectionnez . .
0LW8-048 Restriction des communications au moyen de pare-feu En l'absence de mesures de sécurité adaptées, n'importe qui peut accéder aux ordinateurs et autres périphériques de communication connectés à un réseau. Pour empêcher toute intrusion, il est important de configurer la fonction de filtrage des paquets qui permet de restreindre les communications aux périphériques possédant des adresses IP ou MAC spécifiques.
0LW8-049 Spécification d'adresses IP pour les règles de pare-feu Vous pouvez soit limiter les communications aux seuls périphériques disposant d'adresses IP précises ou au contraire, bloquer les périphériques possédant des adresses IP spécifiques et autoriser toutes les autres communications. Il est possible de définir une adresse IP unique ou une plage d'adresses IP. Vous pouvez spécifier jusqu'à 4 adresses IP (ou plages d'adresses IP) pour les protocoles IPv4 et IPv6.
Sélectionnez cette option pour limiter la réception de données à un ordinateur à partir de l'appareil en spécifiant des adresses IPv4. [Adresse IPv6 : Filtre d'entrée] Sélectionnez cette option pour limiter la réception de données à un ordinateur à partir de l'appareil en spécifiant des adresses IPv6. 5 Définissez les réglages concernant le filtrage des paquets. [Adresses bloquées] Enregistrez les adresses à bloquer, vérifiez ou supprimez également les adresses bloquées.
IPv4 : Spécification d'une plage d'adresses 192.168.0.10192.168.0.20 Insérez un tiret entre les adresses. IPv6 : fe80::10-fe80::20 Spécification d'une plage d'adresses avec un préfixe (IPv6 uniquement) Saisissez l'adresse suivie d'une barre oblique et d'un nombre représentant la longueur du préfixe. fe80::1234/64 Suppression d'une adresse IP des exceptions Sélectionnez une adresse IP et cliquez sur [Supprimer]. 3 Cliquez sur [OK].
0LW8-04A Spécification d'adresses MAC pour les règles de pare-feu Vous pouvez soit limiter les communications aux seuls périphériques disposant d'adresses MAC précises ou au contraire, bloquer les périphériques possédant des adresses MAC spécifiques et autoriser les autres communications. Il est possible de définir jusqu'à 10 adresses MAC. Cette fonction n'est pas disponible si l'appareil est rattaché à un réseau local sans fil. 1 Lancez l'interface utilisateur distante en mode Administrateur système.
1 Cochez la case [Utiliser le filtre]. Cochez la case pour limiter les communications. Désactivez-la pour désélectionner la restriction. 2 Indiquez l'adresse. Saisissez l'adresse MAC dans la zone de texte [Adresse à mémoriser] et cliquez sur [Ajouter]. Autorise les communications (reçues) uniquement avec les périphériques dont les adresses MAC sont enregistrées et restreint la communication avec les périphériques ayant d'autres adresses MAC.
0LW8-04C Modification des numéros de port Les ports font office de points de terminaison pour communiquer avec d'autres périphériques. En règle générale, la plupart des protocoles utilisent des numéros de port conventionnels, mais comme ces numéros de port sont bien connus, les périphériques communiquant par ces ports sont plus vulnérables aux attaques. Pour renforcer la sécurité, votre administrateur réseau peut changer les numéros de port.
0LW8-04E Réglage d'un proxy Un proxy (ou pour être plus précis, un serveur proxy HTTP) est un ordinateur ou un logiciel chargé de gérer les communications HTTP pour le compte d'autres périphériques, notamment en cas de liaison avec des ressources situées à l'extérieur du réseau (consultation de sites Web, par exemple). Les périphériques clients se connectent au réseau externe par l'intermédiaire du serveur proxy et n'entrent pas directement en communication avec les ressources externes.
[Utiliser proxy] Cochez cette case pour utiliser le serveur proxy indiqué lors des communications avec un serveur HTTP. [Adresse du serveur proxy HTTP] Saisissez l'adresse du serveur proxy. La spécification de l'adresse ou du nom d'hôte varie en fonction de l'environnement. [Numéro de port du serveur proxy HTTP] Modifiez si besoin est le numéro de port. Tapez un nombre compris entre 1 et 65 535.
0LW8-04F Restriction des fonctions de l'appareil Il est possible que certaines fonctions de l'appareil soient rarement employées ou donnent lieu à des utilisations abusives ou impropres. Pour des raisons de sécurité, vous pouvez configurer l'appareil de façon à limiter ses capacités en désactivant partiellement ou complètement ces fonctions.
0LW8-04H Désactivation de la communication HTTP Le protocole HTTP permet d'établir une liaison réseau (lors de l'accès à l'appareil via l'interface utilisateur distante, par exemple). Si vous utilisez une connexion USB ou n'avez pas besoin d'établir une communication HTTP, vous pouvez désactiver le mode HTTP pour bloquer les intrusions de tierces parties via le port HTTP inutilisé.
0LW8-04J Désactivation de l'interface utilisateur distante L'interface utilisateur distante est particulièrement pratique dans la mesure où elle permet de spécifier les réglages de l'appareil à partir d'un navigateur Web sur un ordinateur. Pour tirer parti de l'interface utilisateur distante, il est nécessaire de connecter l'appareil à un ordinateur via le réseau.
0LW8-04K Utilisation de l'interface utilisateur distante En utilisant un navigateur Web pour faire fonctionner à distance l'appareil, vous pouvez examiner les documents en attente d'impression ou vérifier l'état de l'appareil. Il est également possible d'effectuer certains réglages relatifs notamment à la sécurité. Vous réalisez toutes ces tâches sans quitter votre poste de travail, ce qui facilite d'autant plus la gestion du système.
0LW8-04L Démarrage de l'interface utilisateur distante Pour travailler à distance, il est nécessaire de saisir l'adresse IP de l'appareil dans un navigateur Web et de lancer l'interface utilisateur distante. Vérifiez l'adresse IP définie au préalable sur l'appareil ( Affichage des réglages réseau). Si vous avez des questions, contactez votre administrateur réseau. 1 2 Démarrez le navigateur Web. Saisissez "http://(l'adresse IP de l'appareil)/" dans la barre d'adresse et appuyez sur la touche [ENTRÉE].
㻞㻝㻠㻌㻛㻌㻟㻠㻜
0LW8-04R Écrans de l'interface utilisateur distante Cette section décrit les écrans types de l'interface utilisateur distante. Page du portail (page principale) Page [Suivi statut/Annulation] Page [Réglages/Enregistrement] Page du portail (page principale) [Se déconnecter] Permet de quitter l'interface utilisateur distante. La page de connexion s'affiche.
[Vers le portail] Affiche de nouveau la page du portail (page principale). Menu Cliquez sur un élément ; le contenu s'affiche à la page qui convient. l'appareil Gestion de documents et vérification de l'état de Fil d'Ariane Indique la série de page auxquelles vous avez accédé pour ouvrir la page actuellement à l'écran. Vous pouvez contrôler la page actuellement affichée. Icône d'actualisation Actualise la page actuellement affichée.
Lorsque vous êtes connecté en mode Utilisateur final, seule l'option [Gestion du système] s'affiche.
0LW8-04S Gestion de documents et vérification de l'état de l'appareil Vérification de l'état actuel des documents d'impression Vérification des informations sur les erreurs Vérification des consommables Vérification de la vitesse d'impression maximale Vérification des informations sur l'administrateur système Vérification du compteur du nombre total d'impressions Le nom de fichier du document n'affiche que 255 caractères. Le nom de l'application peut être ajouté au nom du fichier.
Vérification des consommables Le format et le type de la source de papier, le numéro de série de la cartouche de toner et d'autres informations sont affichés. Connectez-vous à l'interface utilisateur distante ( statut/Annulation] [Consommables]. Démarrage de l'interface utilisateur distante) [Suivi Vous pouvez également cliquer sur [Vérifier les détails des consommables] dans la page du portail (page principale) pour afficher l'écran de vérification des consommables.
Vérification des informations sur l'administrateur système Les informations sur l'appareil et l'administrateur système s'affichent. Ces informations sont définies dans [Gestion du système] à la page Réglages de gestion du système [Réglages/Enregistrement]. Connectez-vous à l'interface utilisateur distante ( statut/Annulation] [Infos périphérique].
0LW8-04U Configuration des options de menu de l'interface utilisateur distante Vous pouvez modifier les réglages de l'appareil par le biais de l'interface utilisateur distante. Il est possible de configurer la plupart des réglages au niveau de l'appareil lui-même, mais certains d'entre-eux doivent être modifiés par l'interface utilisateur distante. Vous ne pouvez définir les réglages que si vous êtes connecté en tant qu'administrateur système. 1 2 3 Lancez l'interface utilisateur distante.
Réglages réseau Réseau (MF212w) Réglages de sécurité Sécurité Initialiser informations de réglages Initialiser le menu LIENS Écrans de l'interface utilisateur distante 㻞㻞㻞㻌㻛㻌㻟㻠㻜
0LW8-04W Liste des menus des réglages Cet appareil comporte différents réglages que vous pouvez définir de façon détaillée. Accédez à ces réglages en appuyant sur Vous pouvez imprimer le menu des réglages sous forme de liste pour vérifier les réglages actuels : Rapport de sortie 㻞㻞㻟㻌㻛㻌㻟㻠㻜 .
0LW8-04X Réglages réseau Tous les réglages relatifs au réseau répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). Si un écran vous invitant à saisir un code PIN apparaît, saisissez le code PIN à l'aide des touches numériques et appuyez sur .
Sélectionnez ce réglage pour configurer une connexion sans fil en saisissant manuellement un SSID. Cette méthode permet de Configuration de la connexion par la définition des réglages définir de façon détaillée l'authentification et le cryptage.
Vérifier les réglages Obtention automatique Adresse IP Masque de sous-réseau Adresse de passerelle Commande PING Sélectionnez ce réglage pour contrôler que l'appareil est relié à un ordinateur rattaché au réseau. Test de la connexion réseau Réglages DNS Spécifiez les réglages du serveur DNS (Domain Name System) qui fournit un nom d'hôte pour les résolutions des adresses IP. Configuration de DNS Réglages du serveur DNS Serveur DNS primaire: 0.0.0.0 Serveur DNS secondaire: 0.0.0.
Longueur du préfixe Réglages DNS Spécifiez les réglages du serveur DNS (Domain Name System) qui fournit un nom d'hôte pour les résolutions des adresses IP.
Utiliser découverte multidiffusion Désactivé Activé Utiliser HTTP Activez ou désactivez HTTP, requis pour communiquer avec un ordinateur lorsque vous utilisez, par exemple, l'interface utilisateur Désactivation de la communication HTTP distante ou l'impression WSD. Désactivé Activé Réglages du numéro de port Changez les numéros de port des protocoles selon l'environnement réseau.
Acquérir les informations de gestion d'impression depuis l'hôte Activez ou désactivez la surveillance des informations de gestion de l'imprimante à partir d'un ordinateur en réseau exécutant un logiciel SNMP. Désactivé Activé d'impression depuis l'hôte> ou Réglages port dédié Activez ou désactivez le port dédié.
100BASE-TX Activé Adresse MAC Vérifiez l'adresse MAC de l'appareil représentant un nombre unique pour chaque appareil de communication. l'adresse MAC Affichage de Initialiser réglages réseau Ce réglage permet de rétablir les valeurs par défaut des réglages réseau.
0LW8-04Y Rapport de sortie Vous pouvez vérifier la liste des différents réglages ainsi que le contenu qui a été enregistré dans l'appareil en imprimant la liste des données de l'utilisateur. Les rapports ou les listes peuvent être imprimés sur papier A4 ou Lettre.
0LW8-050 Préférences Tous les réglages relatifs à l'affichage répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). Si un écran de saisie du code PIN s'affiche Saisissez le code PIN à l'aide des touches numériques et appuyez sur . Définition du PIN administrateur système Astérisques (*) Les réglages signalés par un astérisque (*) ont des valeurs par défaut différentes selon le pays ou la région d'achat.
régler la luminosité Utilisez / pour Inverser couleurs écran Sélectionnez pour inverser les couleurs de l'affichage. Sélectionnez si la visibilité de l'affichage est difficile après le l'ajustement du réglage . Désactivé Activé Sélectionnez ou Basculer entre saisie pouces/mm Sélectionnez l'unité de mesure.
la vitesse Sélectionnez Déplacement du curseur Configurez la façon dont le curseur se déplace après la saisie d'un caractère à l'écran. Sélectionnez pour que le curseur glisse automatiquement à droite du caractère. Sélectionnez pour déplacer manuellement le curseur à droite du caractère saisi.
0LW8-051 Réglages horloge Tous les réglages relatifs à l'horloge répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). REMARQUE Astérisques (* ) Les réglages signalés par le signe "*1" peuvent ne pas être disponibles ou avoir des valeurs par défaut différentes selon le pays ou la région d'achat. Les réglages signalés par le signe "*2" ne sont disponibles que sur MF212w. Minuteur du mode silencieux Réglages date/heure Délai veille auto.
Format heure Sélectionnez le réglage d'affichage de l'horloge en format 12 ou 24 heures. 12 heures (AM/PM) 24 heures le réglage d'affichage Sélectionnez Réglages date/heure actuelle Définissez la date et l'heure courantes. Utilisez matin à l'après-midi (/).
Délai veille auto. Si l'appareil ne fonctionne pas ou n'a pas de données à traiter pendant un délai donné, l'appareil entre en mode de veille afin de réaliser des économies d'énergie (veille automatique). Définissez le délai après lequel la veille automatique est appliquée. La mise en veille est impossible si l'écran des menus est affiché. Il est recommandé d'utiliser les valeurs par défaut pour une gestion optimale de la fonction Activation du mode de veille d'économie d'énergie.
0 (l'appareil reste en ligne.) 1 à 5 , jusqu'à 60 (min) Définissez le délai Délai de fermeture automatique Définissez un délai visant à éteindre automatiquement l'appareil passé le délai d'inactivité fixé alors que l'appareil est en mode de veille.
0LW8-052 Réglages copie Tous les réglages relatifs à la fonction de copie répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). Modifier les réglages par défaut Corriger densité Modifier les réglages par défaut Vous pouvez modifier les réglages par défaut de copie. Les réglages sélectionnés sont appliqués par défaut à la fonction de copie.
0LW8-053 Réglages de lecture Tous les réglages relatifs à la numérisation répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). Régl clé de raccourci Mémorisez les réglages de numérisation sur les touches et (pour le modèle MF211, sur la touche ). Ces réglages indiquent l'ordinateur sur lequel les images numérisées sont enregistrées, le type de numérisation (couleur ou noir et blanc) et le format de fichier (PDF ou JPEG).
0LW8-054 Réglages d'impression Tous les réglages relatifs à la fonction d'impression répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). Action si le format papier est différent Demi-teintes d'impression mobile* Priorité Vitesse AirPrint/Qualité d'image* Astérisques (* ) Les réglages signalés par un astérisque (* ) ne sont disponibles que sur MF212w.
Précisez si vous préférez la vitesse de copie à la qualité de l'image ou inversement lorsque vous utilisez AirPrint.
0LW8-055 Réglages/Maintenance Tous les réglages relatifs à la configuration et à l'entretien répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). Économie de toner Traitement spécial Nettoyer ensemble de fixation Économie de toner Sélectionnez ce réglage pour limiter la consommation de toner lors des copies.
(notamment en cas d'humidité élevée). Mode spécial V Ajustez ce réglage si le papier imprimé s'enroule ou est froissé. Désactivé Mode 1 Mode 2 Mode 3 Sélectionnez le mode Pour activer le réglage Ce réglage est activé seulement dans les conditions suivantes.
de à . Après avoir imprimé à partir d'un smartphone/d'une tablette Si les impressions présentent des traînées, modifiez le réglage avec . Mode spécial B Ajustez ce réglage si les impressions présentent des traînées après le remplacement de la cartouche de toner ou après une longue période d'inutilisation de l'appareil.
Désactivé Activé Sélectionnez ou Une fois le réglage activé En cas de réglage sur , celui-ci est prioritaire sur le réglage de . Si l'effet obtenu est plus important qu'avec , la vitesse d'impression est plus lente. Après avoir imprimé à partir d'un smartphone/d'une tablette Si les impressions présentent des traînées, modifiez le réglage avec .
La définition peut être affectée De l'encre apparaît dans les zones non imprimées lors de l'utilisation d'une nouvelle cartouche de toner L'encre est consommée plus rapidement Mode spécial K Si le toner ne se fixe pas correctement et les impressions sont trop pâles, sélectionnez . Désactivé Activé En cas de réglage sur La vitesse d'impression est plus lente.
0LW8-056 Réglages de gestion du système Tous les réglages relatifs à la gestion du système répertoriés s'accompagnent d'une brève description. Les réglages par défaut sont signalés par une croix ( ). REMARQUE Astérisques (* ) Les réglages signalés par le signe "*1" ne sont disponibles que sur MF212w. Les réglages signalés par le signe "*2" ont des valeurs par défaut différentes selon le pays ou la région d'achat.
ou ( Saisie du texte) Sélectionnez Saisissez ou Réglages de sécurité *1 Activez ou désactivez les réglages du filtrage des paquets via l'adresse IP ou l'adresse MAC. Filtre d'adresse IPv4 Activez ou désactivez les réglages pour le filtrage des paquets reçus à partir d'appareils dotés d'adresses IPv4.
Sélectionnez ou Choisir Pays/Région *2 Indiquez le pays ou la région où l'appareil est utilisé. La valeur par défaut varie selon le réglage que vous avez choisi à la mise sous tension initiale.
Utiliser comme périphérique USB Activez ou désactivez le port USB utilisé pour connecter l'appareil à un ordinateur. Désactivé Activé Redémarrez l'appareil ou Sélectionnez Activer Product Extended Survey Program Active ou désactive le programme Product Extended Survey Program (programme pour recueillir des informations sur l'appareil).
Sélection PDL (Plug-n-Play) Sélectionnez une langue de description de page de sorte que l'appareil soit détecté en tant qu'imprimante compatible avec cette langue lorsqu'il est relié à un ordinateur par Plug and Play. Guide d'installation du pilote MF Réseau *1 Sélectionnez une langue de description de page de sorte que l'appareil soit détecté en tant qu'imprimante compatible avec cette langue lorsqu'il est relié à un ordinateur par le réseau.
Initialiser réglages de gestion système Ce réglage permet de rétablir les valeurs par défaut des réglages de gestion du système. Vous pouvez rétablir simultanément l'ensemble Initialisation des réglages de gestion du système des réglages. Réglages réseau *1 Réglages infos administrateur système Réglages infos sur le périphérique Réglages de sécurité *1 Réglages IU distante *1 Connexion auto pr lecture à distance Utiliser comme périphérique USB Activer Product Extended Survey Program Aff. info consom.
0LW8-057 Initialiser le menu Ce réglage permet de rétablir les valeurs par défaut des réglages indiqués ci-après. Vous pouvez rétablir simultanément l'ensemble des réglages en une opération ou choisir de restaurer les réglages de votre Initialisation du menu choix de manière individuelle. Si un écran vous invitant à saisir un code PIN apparaît, saisissez le code PIN à l'aide des touches numériques et appuyez sur .
0LW8-058 Dépannage En cas de problème, pensez à consulter ce chapitre pour rechercher une solution avant de contacter Canon. Bourrages papier Si un document ou une feuille se coince, consultez la section Élimination de bourrages papier pour dégager le papier bloqué. Un message s'affiche Si l'écran affiche un message, consultez la section suivante.
0LW8-059 Élimination de bourrages papier En cas de bourrage papier, le message s'affiche à l'écran. Appuyez sur pour examiner les solutions les plus simples. Si vous avez des difficultés à comprendre les procédures apparaissant à l'écran, consultez les sections suivantes pour éliminer les bourrages papier. Lorsque vous retirez le papier coincé, n'éteignez pas l'appareil La mise hors tension de l'appareil a pour effet de supprimer les données en cours d'impression.
3 Retirez la cartouche de toner. 2 Tirez doucement le document. 3 Vérifiez si le papier est coincé à l'intérieur du guide de sortie. 4 1 Tirez vers vous en appuyant sur le bouton ( 2 Tirez doucement le document. 3 Fermez le guide de sortie. ) pour ouvrir le guide de sortie. Vérifiez si le papier est coincé à l'intérieur de l'appareil. 1 Tirez doucement le papier entre l'assemblage de fixation ( voir le bord du papier.
2 5 6 Une fois le bord du papier visible, tirez dessus lentement. Vérifiez si du papier est coincé dans la fente d'alimentation manuelle ou la cassette à papier. 1 Tirez doucement sur le papier éventuellement coincé dans la fente d'alimentation manuelle. 2 Ouvrez le capot du papier et retirez tout le papier chargé. 3 Tirez doucement le document. 4 Chargez le papier et fermez la cassette à papier. Installez la cartouche de toner.
7 Fermez le capot toner et abaissez le panneau de commande. Si vous ne parvenez pas à fermer le capot toner Assurez-vous que la cartouche de toner est parfaitement insérée. Si vous forcez pour fermer, vous risquez d'endommager l'appareil.
0LW8-05A Si un message d'erreur apparaît Si la connexion réseau échoue, si la mémoire est pleine ou bien si vous rencontrez des difficultés à utiliser l'appareil, un message apparaît. Vous trouverez de plus amples informations sur les messages dans la liste suivante. La quant. rest. ds la cart. ne s'aff. pas correct. La cartouche de toner n'est pas installée correctement ou un éventuel problème s'est produit au niveau de la cartouche de toner. Réinstallez la cartouche de toner.
La clé réseau (PSK) du routeur sans fil à rattacher n'est pas correctement définie sur l'appareil. Vérifiez la clé réseau (PSK) d'un routeur sans fil et définissez-la à nouveau sur l'appareil.
Chargez le papier. Chargement du papier Le papier sur lequel les rapports ou les listes sont imprimables n'est pas chargé. Les rapports ou les listes sont imprimables sur du papier A4 ou Lettre ordinaire. Chargez le papier A4 ou Lettre ordinaire et indiquez son format. Chargement du papier Spécification du format et du type de papier Pas de réponse de l'hôte. L'appareil n'est pas correctement relié à un réseau. Vérifiez les réglages de l'appareil et du réseau et recommencez la connexion.
Si vous lancez l'impression à partir d'un ordinateur, vérifiez si le réglage du format de papier du pilote d'imprimante correspond au format de papier chargé. Pour charger du papier sans modifier les réglages Chargez le papier dont le format est défini sur . Chargement du papier La connexion avec l'ordinateur a été perdue. Vérifiez la connexion. La connexion avec l'ordinateur a été perdue pendant une numérisation. Vérifiez la connexion entre l'appareil et un ordinateur.
0LW8-05C Problèmes courants Si vous rencontrez des difficultés lors de l'utilisation de l'appareil, passez en revue les points de cette section avant de nous contacter. Si les problèmes persistent, contactez votre revendeur agréé Canon ou composez le numéro d'assistance téléphonique de Canon. Points à vérifier L'appareil est-il allumé ? Le cordon d'alimentation est-il connecté ? Si l'appareil est allumé, mais ne répond pas, éteignez-le, vérifiez le branchement du cordon d'alimentation et rallumez-le.
0LW8-05E Problèmes d'installation ou de réglages Reportez-vous également à la section Problèmes courants. Icônes figurant dans les descriptions Problème concernant la connexion du réseau local sans fil Problème concernant la connexion du réseau local filaire Problème concernant la connexion USB L'appareil ne peut pas se connecter à un ordinateur par un réseau local sans fil, un réseau local filaire et un câble USB simultanément. Il est impossible d'utiliser les trois types de connexion en même temps.
Si un serveur DNS est situé sur un réseau externe, définissez l'adresse IP du système à raccorder, pas le nom d'hôte, même si vous établissez la connexion avec les périphériques figurant sur le réseau relié à l'appareil. Si un serveur DNS est situé sur un réseau relié à l'appareil et que les informations sur les périphériques reliés au réseau externe sont enregistrées sur le serveur DNS, vérifiez si les réglages sont corrects.
0LW8-05F Problèmes de copie Reportez-vous également à la section Problèmes courants. Si les résultats de l'impression ne sont pas satisfaisants. Le papier se froisse ou s'enroule.
0LW8-05H Problèmes d'impression Reportez-vous également à la section Problèmes courants. Si les résultats de l'impression ne sont pas satisfaisants. Le papier se froisse ou s'enroule. Lorsque vous ne pouvez pas imprimer correctement Vous ne pouvez pas imprimer.
0LW8-05J Lorsque vous ne pouvez pas imprimer correctement Si les résultats de l'impression ne sont pas satisfaisants ou si le papier se froisse ou s'enroule, appliquez les solutions suivantes. Si les problèmes persistent, contactez votre revendeur agréé Canon ou composez le numéro d'assistance téléphonique de Canon.
0LW8-05K Les résultats de l'impression ne sont pas satisfaisants Des saletés à l'intérieur de l'appareil peuvent affecter les résultats d'impression. Inspectez et nettoyez soigneusement l'appareil. Entretien de l'appareil Des traces noires apparaissent sur les bords des impressions Imprimez-vous les données sans les marges ? Ce phénomène se produit si aucune marge n'est définie dans le pilote d'imprimante.
Le niveau du toner est-il bas ? Vérifiez la quantité de toner encore disponible et remplacez, au besoin, les cartouches de toner. Remplacement des cartouches de toner Tâches et éclaboussures d'encre Utilisez-vous le papier approprié ? Vérifiez le papier utilisé et remplacez-le par le papier qui convient. Papier Chargement du papier Changez le réglage de .
Les pages imprimées présentent des tâches blanches Utilisez-vous le papier approprié ? Vérifiez le papier utilisé et remplacez-le par le papier qui convient. Papier Chargement du papier Le tambour de la cartouche de toner est-il détérioré ? Remplacez la cartouche de toner par une nouvelle. Remplacement des cartouches de toner Imprimez-vous un document présentant d'importants contrastes ? Changez le réglage de [Mode d'impression spécial] à l'aide du pilote d'imprimante.
Les impressions sont grisâtres Le réglage de dans est-il trop foncé ? Ajustez le réglage afin d'éclaircir la densité. Liste des menus des réglages L'imprimante est-elle installée dans un endroit exposé à la lumière directe du soleil ou à une lumière intense ? Installez l'imprimante dans un lieu approprié.
0LW8-05L Le papier est froissé ou plié Le papier se froisse Le papier est-il correctement chargé ? Si le papier est chargé au-delà de la ligne de limite de chargement ou encore de manière oblique, il peut se froisser. Chargement du papier Utilisez-vous du papier ayant absorbé de l'humidité ? Remplacez-le par du papier qui convient. Chargement du papier Utilisez-vous le papier approprié ? Vérifiez le papier utilisé et remplacez-le par le papier qui convient.
0LW8-05R Le papier est chargé de manière incorrecte Le contenu s'imprime de biais Les guides papier sont-ils alignés sur les bords du papier ? Si les guides papier sont trop serrés ou trop lâches, les documents peuvent s'imprimer de biais sur le papier. Chargement du papier La source de papier correspond-elle à la fente d'alimentation manuelle ? Chargez le papier dans la cassette à papier.
0LW8-05S Lorsqu'un problème ne peut pas être résolu Si vous ne parvenez pas à résoudre un problème après avoir examiné les informations de ce chapitre, contactez votre revendeur agréé Canon ou composez le numéro d'assistance téléphonique de Canon. IMPORTANT Ne tentez pas de démonter ou de réparer vous-même l'appareil Toute opération de démontage ou de réparation de l'appareil risque d'entraîner l'annulation de la garantie.
0LW8-05U Entretien Ce chapitre décrit la manière de tenir à jour l'appareil et notamment les opérations de nettoyage de l'appareil et de réinitialisation des réglages.
0LW8-05W Entretien de l'appareil Nettoyez régulièrement l'appareil pour empêcher la dégradation de la qualité d'impression et garantir une utilisation aisée et sécurisée. Entretien et vérifications Lisez attentivement les consignes de sécurité avant toute opération de nettoyage.
0LW8-05X Extérieur Essuyez régulièrement l'extérieur de l'appareil pour préserver son bon état. 1 Éteignez l'appareil et débranchez le cordon d'alimentation de la prise secteur. Lorsque l'appareil est hors tension, les données en attente d'impression sont effacées. 2 Nettoyez l'extérieur de l'appareil. Utilisez un chiffon doux, bien essoré, humidifié avec de l'eau ou un détergent doux dilué dans l'eau. 3 4 Attentez que l'extérieur de l'appareil sèche complètement.
0LW8-05Y Vitre d'exposition Dépoussiérez régulièrement la vitre d'exposition et la partie intérieure du couvercle de la vitre d'exposition pour éviter que des traces ne s'impriment sur les documents ou les impressions. 1 Éteignez l'appareil et débranchez le cordon d'alimentation de la prise secteur. Lorsque l'appareil est hors tension, les données en attente d'impression sont effacées. 2 Ouvrez le couvercle de la vitre d'exposition.
0LW8-060 Assemblage de fixation Des saletés peuvent coller à l'unité de fixation à l'intérieur de l'appareil et laisser des traînées noires sur les impressions. Pour nettoyer cette pièce, appliquez la procédure suivante. Notez que vous ne pouvez pas nettoyer l'unité de fixation si des documents attendent d'être imprimés dans l'appareil. Pour nettoyer l'unité de fixation, vous avez besoin de papier dont le format est supérieur au papier A4 ou Lettre ordinaire.
0LW8-061 Intérieur de l'appareil Nettoyez l'intérieur de l'appareil régulièrement afin d'éviter l'accumulation de poussière d'encre/de papier. 1 Éteignez l'appareil et débranchez le cordon d'alimentation de la prise secteur. Lorsque l'appareil est hors tension, les données en attente d'impression sont effacées. 2 Soulevez le panneau de commande. Si vous ne parvenez pas à soulever le panneau de commande Veillez à ce que le couvercle de la vitre d'exposition soit complètement fermé.
7 Fermez le capot toner et abaissez le panneau de commande. Si vous ne parvenez pas à fermer le capot toner Assurez-vous que la cartouche de toner est parfaitement insérée. Si vous forcez pour fermer, vous risquez d'endommager l'appareil. 8 Rebranchez le cordon d'alimentation et rallumez l'appareil.
0LW8-062 Remplacement des cartouches de toner L'appareil affiche un message lorsqu'une cartouche de toner est presque vide. Notez que la qualité d'impression se dégrade si vous continuez d'imprimer sans intervention de votre part. Vous pouvez examiner le niveau de toner restant sur l'affichage.
Niveau de toner Affiche la quantité d'encre restante. En fonction de l'environnement dans lequel se trouve l'appareil, il est possible que d'autres pièces internes arrivent en fin de vie avant l'épuisement de l'encre.
0LW8-063 Avant de remplacer la cartouche de toner Procédez comme suit avant de remplacer la cartouche de toner. Le message peut disparaître ou la qualité d'impression peut devenir Entretien et meilleure. Lisez attentivement les précautions de manipulation de la cartouche de toner avant de commencer. Consommables vérifications 1 Soulevez le panneau de commande. Si vous ne parvenez pas à soulever le panneau de commande Veillez à ce que le couvercle de la vitre d'exposition soit complètement fermé.
6 Fermez le capot toner et abaissez le panneau de commande. Si vous ne parvenez pas à fermer le capot toner Assurez-vous que la cartouche de toner est correctement insérée. Si vous forcez pour fermer, vous risquez d'endommager l'appareil.
0LW8-064 Comment remplacer les cartouches de toner Lisez attentivement les consignes des sections toner. 1 Entretien et vérifications et Consommables avant de remplacer les cartouches de Soulevez le panneau de commande. Si vous ne parvenez pas à soulever le panneau de commande Veillez à ce que le couvercle de la vitre d'exposition soit complètement fermé. Si un original épais comme un livre se trouve sur la vitre d'exposition, retirez-le.
6 Enlevez la bande adhésive d'obturation en la tirant à à l'horizontale. La bande adhésive d'obturation mesure environ 50 cm. Lorsque vous retirez la bande adhésive d'obturation Si la bande adhésive d'obturation reste à l'intérieur de la cartouche de toner, la qualité d'impression risque de se dégrader. Ne tirez pas sur la bande d'obturation de biais. Si la bande se rompt, vous aurez beaucoup de mal à la retirer complètement.
0LW8-065 Déplacement de l'appareil L'appareil est lourd. Suivez scrupuleusement les procédures décrites ci-après lorsque vous déplacez l'appareil de façon à écarter tout Consignes de sécurité importantes risque de blessure et veillez également à lire les consignes de sécurité avant toute chose. 1 Mettez l'appareil et l'ordinateur sous tension. Lorsque l'appareil est hors tension, les données en attente d'impression sont effacées.
0LW8-066 Affichage de la valeur du compteur Vous pouvez consulter le nombre total de pages utilisées pour les impressions. Ces totaux comprennent les listes en plus des copies et des impressions de données réalisées à partir d'ordinateurs.
0LW8-067 Initialisation des réglages Vous pouvez rétablir les valeurs par défaut des réglages suivants : Initialisation du menu Initialisation des réglages de gestion du système Initialisation de toutes les données/tous les réglages 㻞㻥㻞㻌㻛㻌㻟㻠㻜
0LW8-068 Initialisation du menu Vous pouvez rétablir les valeurs par défaut des réglages de l'appareil ( Liste des menus des réglages). Pour initialiser les réglages et , voir gestion du système. Initialisation des réglages de Si un écran vous invitant à saisir un code PIN apparaît, saisissez le code PIN à l'aide des touches numériques et appuyez sur .
0LW8-069 Initialisation des réglages de gestion du système Vous pouvez restaurer les réglages de l'appareil ( redémarrage de la machine. Liste des menus des réglages). L'initialisation de certains réglages demande le Si un écran vous invitant à saisir un code PIN apparaît, saisissez le code PIN à l'aide des touches numériques et appuyez sur .
0LW8-06A Initialisation de toutes les données/tous les réglages Pour apporter des modifications aux données et réglages enregistrés en une seule opération, comme lorsque vous changez l'emplacement d'installation de la machine, vous pouvez supprimer les données enregistrées et initialiser tous les réglages ( Liste des menus des réglages) simultanément. Vous devrez redémarrer l'appareil une fois cette initialisation effectuée.
0LW8-06C Annexe Ce chapitre contient les caractéristiques techniques de cet appareil, des instructions sur l'utilisation du manuel électronique, des informations sur les limites de responsabilité et les droits d'auteur et divers autres renseignements importants pour les clients.
0LW8-06E Descriptions des fonctions Découvrez les fonctions décrites dans cette section. Les fonctions sont rassemblées en quatre rubriques : "Empreinte environnementale et maîtrise des coûts", "Gain de productivité", "Passage au numérique" et "Nouvelles perspectives".
0LW8-06F Empreinte environnementale et maîtrise des coûts Imprimer plusieurs pages sur une seule feuille Pour commencer à réduire votre consommation de papier, imprimez plusieurs pages sur une seule feuille de papier : 2 ou 4 pages en cas de copie et jusqu'à 16 pages pour les tâches d'impression envoyées à partir de l'ordinateur.
0LW8-06H Gain de productivité Touches de raccourci pour la numérisation Tirez parti des touches de raccourci du panneau de commande au lieu de spécifier sans cesse les mêmes réglages. Utilisez * pour prédéfinir vos destinataires, vos types de numérisation ainsi que vos formats de fichiers / les touches favoris. Il ne vous reste alors plus qu'à mettre l'orignal en place et à appuyer sur une des touches de raccourci pour lancer la numérisation.
Pour plus d'informations Impression d'un document 㻟㻜㻜㻌㻛㻌㻟㻠㻜
0LW8-06J Passage au numérique Numériser uniquement ce dont vous avez besoin Vous numérisez l'intégralité d'une page de journal, mais tout ce qui vous intéresse se trouve dans le titre et une photo ? Utilisez ScanGear MF. Vous sélectionnez la partie qui vous intéresse à l'aide de l'aperçu et demander au scanner d'ignorer le reste du document. Autrement, vous serez amené à utiliser un programme d'édition pour détourer les informations qui ne présentent aucun intérêt à vos yeux.
Le texte est habituellement numérisé sous la forme d'une image, mais vous êtes libre de la convertir en texte que vous pouvez alors modifier. Sélectionnez le type de numérisation "OCR" au moment où vous numérisez le document avec le programme MF Toolbox. Le logiciel, livré avec cet appareil, convertit n'importe quel texte en image et l'image en données de texte que vous avez ensuite la possibilité d'éditer dans une application de traitement de texte.
0LW8-06K Nouvelles perspectives Avec un smartphone/une tablette (MF212w) Vous pouvez utiliser cette fonction pour imprimer ou numériser un projet sur lequel vous travaillez tandis que vous vous rendez à une réunion d'affaires à l'aide d'une tablette, de photos prises sur un smartphone ou de documents distribués lors d'une réunion. Avec Mopria TM , vous pouvez, par exemple, imprimer grâce à un seul pilote et même avec une imprimante d'une autre marque.
Placez-les côte à côte selon une grille 3 x 3 et le tour est joué ! Pour plus d'informations sur cette fonction, voir Impression de posters.
0LW8-06L Caractéristiques Les caractéristiques de l'appareil peuvent faire l'objet de modifications sans préavis en raison d'améliorations apportées à l'appareil.
0LW8-06R Caractéristiques de l'appareil Type Ordinateur de bureau personnel Alimentation *1 220 à 240 V, 50/60 Hz (Les caractéristiques électriques varient selon le pays où vous avez acheté le produit.
0LW8-06S Caractéristiques de réseau sans fil Standard IEEE 802.11g, IEEE 802.11b, IEEE 802.11n Plage de fréquences 2 412 à 2 472 MHz IEEE 802.11g 6/9/12/18/24/36/48/54 Mbits/s Débit de transmission de données IEEE 802.11b 1/2/5,5/11 Mbits/s IEEE 802.
0LW8-06U Type de document Types de document pris en charge Type Papier ordinaire/Papier épais/Photo/Petits documents (par exemple des fiches)/Types de papier spéciaux (par exemple, du papier calque, des transparents, etc.
0LW8-06W Zone de lecture Les zones grisées illustrées dans le tableau ci-dessous représentent la zone de lecture du document. Assurez-vous que le texte et les images de vos documents ne dépassent pas de la zone grisée. La zone de lecture varie selon la fonction utilisée et l'emplacement des documents. Copie La zone de lecture utilisée lors de la copie peut différer de la zone imprimable.
0LW8-06X Papier Formats papier pris en charge Voici la liste des formats de papier qu'il est possible de charger dans la cassette à papier et la fente d'alimentation manuelle.
Papier épais 105 à 163 g/m² 100 feuilles 1 feuille 60 à 80 g/m² 250 feuilles 1 feuille 80 à 90 g/m² 170 feuilles 1 feuille 60 à 80 g/m² 250 feuilles 1 feuille 80 à 90 g/m² 170 feuilles 1 feuille 60 à 163 g/m² 100 feuilles 1 feuille 50 feuilles 1 feuille 100 feuilles 1 feuille 20 feuilles 1 feuille Papier recyclé Papier couleur Papier de luxe Transparents*1 Etiquettes Enveloppes *1 Utilisez des transparents pour imprimante laser.
0LW8-06Y Caractéristiques de copie Résolution de numérisation Texte/Photo (Vitesse accélérée) 300 x 600 ppp Texte/Photo, Photo, Texte 600 x 600 ppp Résolution de sortie 600 x 600 ppp Taux de reproduction 100 % 1:1, 400 % max., 200 %, 141 % A5->A4, 70 % A4->A5, 50 %, 25 % min.
0LW8-070 Caractéristiques du scanner Type Scanner couleur Format de lecture maximal Jusqu'à 216 x 297 mm Résolution de numérisation Pilote Résolution optique Jusqu'à 600 x 600 ppp Résolution d'interpolation logicielle 9 600 x 9 600 ppp TWAIN WIA 1.0 (Windows XP) WIA 2.
0LW8-071 Caractéristiques de l'imprimante Réceptacle de sortie *1 (pile neuve de papier au format A4) Vitesse d'impression *2 (A4 Ordinaire 1:1) Durée première impression*3 100 feuilles environ (68 g/m²) 23 ppm 6 secondes ou moins (A4) Résolution d'impression 600 x 600 ppp (1 200 ppp équivalent x 1 200 ppp équivalent) Demi-teintes 256 teintes Cartouches de toner Consommables *1 Variable en fonction de votre environnement d'installation et du type de papier utilisé.
0LW8-072 Consommables Vous trouverez ci-après un guide de remplacement des consommables utilisés dans cet appareil, basé sur des estimations. Procurez-vous vos consommables auprès d'un distributeur régional Canon agréé. Respectez les précautions en matière de sécurité et de santé lorsque vous stockez et manipulez les consommables (Consommables).
0LW8-073 Manuels inclus avec l'appareil Les manuels mentionnés ci-dessous sont inclus avec l'appareil, consultez-les en cas de besoin. Mise en route Lisez d'abord ce manuel : il décrit l'installation ainsi que les procédures de configuration générales (du retrait de l'emballage à la configuration de l'appareil). Manuel électronique (ce manuel) Ce document décrit toutes les fonctions de l'appareil, accessibles par un navigateur Web.
0LW8-074 Utilisation du manuel électronique Le manuel électronique est un manuel pouvant être consulté sur un ordinateur qui décrit toutes les fonctions de l'appareil. Il est possible de le consulter dans le cadre de l'usage que vous souhaitez faire de l'appareil ou de saisir un mot clé afin de retrouver rapidement la page que vous recherchez. Vous pouvez utiliser le manuel électronique en l'installant sur l'ordinateur ou l'ouvrir directement à partir du DVD-ROM.
0LW8-075 Installation du manuel électronique Installez sur votre ordinateur le manuel électronique en exécutant le DVD-ROM livré avec l'appareil. 1 Insérez le User Software and Manuals DVD-ROM dans le lecteur de l'ordinateur. Sélectionnez une langue et cliquez sur [OK] si un message vous invite à le faire.
5 Lisez attentivement le contrat de licence et cliquez sur [Oui] pour l'accepter. 6 Sélectionnez le dossier à installer et cliquez sur [Installer]. L'installation démarre. Patientez quelques instants, cette opération peut prendre un peu de temps. 7 Cliquez sur [Quitter]. 8 Cliquez sur [Suivant] [Quitter].
Affichage du manuel électronique Double-cliquez sur l'icône de raccourci du manuel électronique du bureau. Si un message d'avertissement s'affiche Cliquez sur [Autoriser le contenu bloqué]. Consultation du manuel électronique directement sur le DVD-ROM 1 Insérez le CD-ROM "User Software and Manuals DVD-ROM" dans le lecteur de l'ordinateur. Sélectionnez une langue et cliquez sur [OK] si un message vous invite à le faire.
0LW8-076 Désinstallation du manuel électronique Vous pouvez supprimer le manuel électronique de l'ordinateur afin de rétablir l'état dans lequel se trouvait l'ordinateur avant l'installation de ce manuel. 1 Insérez le User Software and Manuals DVD-ROM dans le lecteur de l'ordinateur. Sélectionnez une langue et cliquez sur [OK] si un message vous invite à le faire. 2 Cliquez sur [Démarrer les programmes]. Si l'écran ci-dessus ne s'affiche pas, reportez-vous à la section programmes/manuels].
6 Cliquez sur [Précédent] [Quitter].
0LW8-077 Disposition à l'écran du manuel électronique Le manuel électronique comporte plusieurs écrans dont le contenu varie. Page d'accueil S'affiche au démarrage du manuel électronique. Canon Cliquez ici pour revenir en haut de la page. Onglet [Sommaire]/Onglet [Recherche] Cliquez sur l'onglet pour passer de la table des matière à la zone de recherche et inversement. Sommaire Les titres des chapitres s'affichent ( ).
Cliquez ici pour afficher les informations indiquant comment feuilleter le manuel électronique, effectuer une recherche et obtenir d'autres renseignements. [Imprimer] Cliquez sur imprimer le contenu affiché. Descriptions des fonctions Présente plusieurs cas pratiques illustrant les différentes utilisations possibles de l'appareil. Cliquez sur / / / pour afficher les cas pratiques par catégorie ou cliquez sur l'écran qui défile pour obtenir des informations détaillées sur chaque Descriptions des catégorie.
[Sommaire] Les icônes et les titres des chapitres s'affichent. / L'onglet [Sommaire] peut être élargi ou réduit à votre convenance. [Tout développer]/[Tout réduire] Cliquez sur [Tout développer] pour afficher toutes les sections secondaires des rubriques. Cliquez sur [Tout réduire] pour fermer les sections secondaires pour toutes les rubriques. Icônes des chapitres Cliquez sur l'icône d'un chapitre pour accéder en haut du chapitre associé. Page de la rubrique Affiche les rubriques du chapitre sélectionné.
[Saisir mot(s) clé(s) ici] Saisissez un ou plusieurs mots clés et cliquez sur recherche ( ). pour afficher les résultats de la recherche dans la boîte de dialogue de [Options de recherche] Cliquez ici pour indiquer les conditions de recherche telles que la portée de la recherche et les conditions de la correspondance. Pour afficher les conditions, cliquez sur ce bouton lorsqu'il est grisé. Pour fermer cet écran, cliquez sur le bouton lorsqu'il est orange.
Icônes des chapitres Cliquez ici pour accéder à la rubrique du chapitre sélectionné. Titre (rubrique) Affiche les titres et les rubriques. Cliquez sur un titre ou une rubrique pour accéder à la page correspondante. Cliquez ici pour revenir en haut de la page. / Cliquez ici pour accéder au chapitre précédent ou suivant.
0LW8-078 Affichage du manuel électronique Conventions Les instructions relatives à la sécurité, les restrictions et les précautions liées à la manipulation de l'appareil, les conseils pratiques et d'autres informations sont signalées de la manière suivante. Avertissement concernant les opérations susceptibles de représenter un danger de mort ou de provoquer des blessures si les instructions ne sont pas respectées. Ces recommandations sont à respecter rigoureusement.
0LW8-079 Autres Cette section décrit les opérations Windows de base et incluent les limites de responsabilité, les informations relatives aux droits d'auteur ainsi que d'autres informations.
0LW8-07A Fonctionnement de base sous Windows Affichage de [Ordinateur] ou [Poste de travail] Windows XP Professionnel/Server 2003/Server 2003 R2 [Démarrer] sélectionnez [Poste de travail]. Windows Vista/7/Server 2008/Server 2008 R2 [Démarrer] sélectionnez [Ordinateur]. Windows 8/Server 2012 Cliquez avec le bouton droit sur le coin gauche en bas de l'écran Windows 8.
Affichage de l'écran [Installation des programmes/manuels] Si l'écran [Installation des programmes/manuels] ne s'affiche pas sur l'ordinateur alors que vous avez inséré le DVD-ROM, procédez comme suit. Dans ce manuel, le nom du lecteur de DVD-ROM correspond à la lettre "D:". Toutefois, votre lecteur de DVD-ROM peut porter un autre nom sur votre ordinateur. Windows XP/Server 2003/Server 2003 R2 1 [Démarrer] 2 Tapez "D:\Minst.exe", puis cliquez sur [OK]. sélectionnez [Exécuter].
[Propriétés]) dans le menu contextuel. 4 Imprimez une page de test. Cliquez sur l'onglet [Général]. Cliquez sur [Imprimer une page de test] pour imprimer la page de test. Vérification de l'architecture en bits Si vous n'êtes pas sûr que l'ordinateur exécute une version 32 bits ou 64 bits de Windows Vista/7/8/8.1/Server 2008/Server 2008 R2/Server 2012/Server 2012 R2, procédez comme suit. 1 Affichez [Panneau de configuration].
Affichage du nom de l'ordinateur Windows XP/Server 2003/Server 2003 R2 1 [Démarrer] 2 Affichez l'écran [Système]. sélectionnez [Panneau de configuration]. Cliquez sur [Performance et maintenance] [Système]. 3 Cliquez sur l'onglet [Nom de l'ordinateur] (ou [ID réseau]). 4 Cliquez sur [Modifier] (ou sur [Propriétés]). Windows Vista/7/8/8.1/Server 2008/Server 2008 R2/Server 2012/Server 2012 R2 1 Affichez [Panneau de configuration].
1 2 3 Cliquez avec le bouton droit sur l'icône de l'imprimante, puis cliquez sur [Propriétés de l'imprimante] (ou [Propriétés]) dans le menu contextuel. Vérifiez la configuration du port. Cliquez sur l'onglet [Ports]. Assurez-vous que le bon port est sélectionné pour l'imprimante.
0LW8-07C Si vous utilisez Mac OS Selon la date d'achat de votre appareil, il est possible que celui-ci ne dispose pas d'un pilote Mac OS. En cas de besoin, les pilotes sont disponibles sur le site Web de Canon. Vérifiez le système d'exploitation de votre ordinateur et téléchargez le pilote approprié à partir du site Web de Canon. Pour plus d'informations sur la procédure d'installation du pilote et son utilisation, consultez le "Guide d'installation du pilote MF".
0LW8-07E Avis Services et logiciels tiers Logiciels tiers (MF212w) Logiciels tiers (MF211) Exigences CEM de la directive européenne Cet équipement est conforme aux principales exigences CEM de la directive européenne. Ce produit est conforme aux spécifications CEM de la directive européenne pour une alimentation secteur nominale de 230 V, 50 Hz, avec une tension nominale de 220 V – 240 V, 50/60 Hz.
Union Européenne, Norvège, Islande et Liechtenstein uniquement. Ces symboles indiquent que ce produit ne doit pas être mis au rebut avec les ordures ménagères, comme le spécifient la Directive européenne DEEE (2012/19/UE), la Directive européenne relative à l'élimination des piles et des accumulateurs usagés (2006/66/CE) et les lois en vigueur dans votre pays appliquant ces directives.
relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente CANON INC. declara que el AW-NM383 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. [Greek] ¡¢£¤¥¦¢ §¨ © ¤ ª¤ «¤ ¦¬ªª¤£¨ ¢ ¡£¤¯ ¯ ¤¬¦¨§¯ ¢¡¢ ¦¯ ¢ ¯ ¤¡«¯ ¦± «¯ §¢ ³´¯ ¯ µ§¶·¢¯ ¸ Français [French] Par la présente, CANON INC.
Les informations contenues dans ce document peuvent être modifiées sans avis préalable. À L'EXCEPTION DE LA GARANTIE CI-INCLUSE, CANON INC. NE FOURNIT AUCUNE AUTRE GARANTIE QUELCONQUE AVEC CETTE MACHINE, EXPLICITE OU IMPLICITE, Y COMPRIS MAIS NON LIMITÉE À TOUTE GARANTIE DE COMMERCIALISATION, DE VALEUR COMMERCIALE, D'ADÉQUATION À UN USAGE PARTICULIER OU DE CONTREFAÇON. CANON INC.
0LW8-07F Nous contacter CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON MARKETING JAPAN INC. 16-6, Konan 2-chome, Minato-ku, Tokyo 108-8011, Japan CANON U.S.A., INC. One Canon Park, Melville, NY 11747, U.S.A. CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands CANON CHINA CO. LTD. 15F Jinbao Building No.
㻝㻌㻛㻌㻠㻤
Introduction 3 A propos des pilotes et des logiciels 4 Systèmes d'exploitation pris en charge 5 Sélection du pilote à installer 6 Installation 8 Installation à l'aide du CD-ROM/DVD-ROM fourni 9 Installation après téléchargement depuis le site Web de Canon 21 Installation pour utiliser WSD 28 Désinstallation 33 Dépannage 37 Annexe 38 Utilisation du guide d'installation 39 Configuration des écrans du guide d'installation 40 Affichage du guide d'installation 43 Autre 44 Fonctionnement de base sous Windows 45 A
0LE4-000 Introduction Ce guide d'installation explique comment installer et désinstaller les pilotes MF et MF Toolbox. Configuration système requise pour l'installation des pilotes MF ou de MF Toolbox ( Systèmes d'exploitation pris en charge Installation Cette section explique comment installer les pilotes MF et MF Toolbox afin que l'appareil soit prêt à imprimer depuis un ordinateur. Installation Désinstallation Cette section explique comment désinstaller les pilotes MF ou MF Toolbox.
0LE4-001 A propos des pilotes et des logiciels Veillez à lire ce qui suit avant d'installer les pilotes MF ou tout autre logiciel. L'installation varie selon le mode de connexion et l'environnement. Pilotes MF Pilote d'imprimante Vous pouvez imprimer depuis une application sur l'appareil une fois que le pilote d'imprimante est installé sur votre ordinateur.
0LE4-002 Systèmes d'exploitation pris en charge Vérifiez la prise en charge des pilotes MF et de MF Toolbox pour chaque système d'exploitation. : pris en charge : non pris en charge Windows XP Windows Vista/7/8/8.
0LE4-003 Sélection du pilote à installer Avant d'installer les pilotes MF sur l'appareil, spécifiez le mode de connexion avec l'ordinateur et les types de pilotes à utiliser. Utilisation d'un modèle doté d'une fonction de télécopie Utilisation d'un modèle sans fonction de télécopie Utilisation d'un modèle doté d'une fonction de télécopie 1 Appuyez sur 2 Appuyez sur . 3 4 5 et appuyez sur
4 5 Utilisez / pour sélectionner ou , et appuyez sur . Utilisez / pour sélectionner le pilote que vous utilisez, et appuyez sur . Langue de description des pages sélectionnable 6 Réseau UFRII LT UFRII LT (XPS) USB UFRII LT UFRII LT (XPS) Redémarrez l'appareil. Si vous avez sélectionné à l'étape 4, éteignez l'appareil et attendez au moins 10 secondes avant de le rallumer.
0LE4-004 Installation Cette section explique comment installer les pilotes MF et MF Toolbox afin que l'appareil soit prêt à imprimer depuis un ordinateur. Installation à l'aide du CD-ROM/DVD-ROM fourni Installez les pilotes MF et MF Toolbox à l'aide du CD-ROM/DVD-ROM User Software and Manuals livré avec l'appareil. Effectuez la Installation à l'aide du CDprocédure de configuration ; de la connexion entre l'appareil et l'ordinateur à l'installation des pilotes.
0LE4-005 Installation à l'aide du CD-ROM/DVD-ROM fourni L'ordre des opérations pour une installation facile est "Installer les pilotes" "Installer le logiciel fourni avec le CD-ROM/DVD-ROM" "Installer le manuel électronique". Pour plus d'informations sur la connexion de l'appareil à un ordinateur, consultez "Mise en route" avant de commencer.
Connexion par réseau câblé/sans fil Sélectionnez [Connexion réseau] et cliquez sur [Suivant]. Sous Server 2003/Server 2008/Server 2008 R2/Server 2012/Server 2012 R2, cet écran ne s'affiche pas. Procédez de la façon suivante. 5 Cliquez sur [Installer]. 6 Lisez attentivement le contrat de licence et cliquez sur [Oui] pour l'accepter.
7 Cliquez sur [Suivant]. Pour connecter l'appareil à un ordinateur via un réseau, passez à l'étape 8. Pour connecter l'appareil à un ordinateur via un câble USB, passez à l'étape 10. L'installation des pilotes démarre. Lorsque l'écran suivant apparaît, cliquez sur [Oui]. 8 Sélectionnez l'appareil et cliquez sur [Suivant].
Si aucun appareil ne s'affiche dans [Liste des périphériques] Vérifiez la connexion de l'ordinateur et de l'appareil et les réglages de l'adresse IP (Affichage des réglages réseau (Manuel électronique)), et cliquez sur [Mettre liste des périphériques à jour]. Si l'appareil ne s'affiche toujours pas, cliquez sur saisissez l'adresse IP définie sur l'appareil [OK]. [Rechercher par adresse IP] 9 Vérifiez les réglages et cliquez sur [Démarrer]. L'installation des pilotes démarre. 10 Cliquez sur [Quitter].
14 15 Suivez les instructions à l'écran pour installer le manuel électronique. Lisez attentivement les informations de l'écran suivant, sélectionnez [Accepter] ou [Ne pas accepter], puis cliquez sur [Suivant]. Si vous sélectionnez [Accepter], le Product Extended Survey Program est installé. Le Product Extended Survey Program est un programme qui enverra à Canon des informations de base relatives à l'installation et à l'utilisation de l'imprimante tous les mois pendant 10 ans.
Si vous souhaitez installer les logiciels standards et le manuel électronique sur votre ordinateur, cliquez sur [Installation facile]. Si l'écran ci-dessus ne s'affiche pas, consultez la section Affichage de l'écran [Installation par CD-ROM/DVD-ROM]. Si [Exécution automatique] s'affiche, cliquez sur [Exécuter MInst.exe]. 4 Sélectionnez le mode de connexion avec l'ordinateur. Connexion USB Sélectionnez [Connexion USB] et cliquez sur [Suivant].
6 Lisez attentivement le contrat de licence et cliquez sur [Oui] pour l'accepter. 7 Cliquez sur [Suivant]. Pour connecter l'appareil à un ordinateur via un réseau, passez à l'étape 8. Pour connecter l'appareil à un ordinateur via un câble USB, passez à l'étape 13. L'installation des pilotes démarre. Lorsque l'écran suivant apparaît, cliquez sur [Oui].
8 Sélectionnez l'appareil et cliquez sur [Suivant]. Si aucun appareil ne s'affiche dans [Liste des périphériques] Vérifiez la connexion de l'ordinateur et de l'appareil et les réglages de l'adresse IP (Affichage des réglages réseau (Manuel électronique)), et cliquez sur [Mettre liste des périphériques à jour]. Si l'appareil ne s'affiche toujours pas, cliquez sur saisissez l'adresse IP définie sur l'appareil [OK].
[Nom de l'imprimante]/[Nom du télécopieur] Changez le nom si besoin. [Utiliser comme imprimante partagée]/[Utiliser comme télécopieur partagé] Cochez cette case si vous voulez partager l'appareil (en utilisant l'ordinateur depuis lequel vous effectuez l'installation comme serveur d'impression). Configuration du serveur d'impression (Manuel électronique) [Nom de partage] Changez le nom partagé si besoin.
15 16 17 Sélectionnez le dossier d'installation et cliquez sur [Suivant]. Spécifiez le dossier auquel ajouter une icône et cliquez sur [Suivant]. Cliquez sur [Démarrer]. L'installation de MF Toolbox démarre. 18 19 20 21 Cliquez sur [Quitter]. Suivez les instructions à l'écran pour installer Toner Status. Suivez les instructions à l'écran pour installer Presto! PageManager et le manuel électronique.
avoir retiré le CD-ROM/DVD-ROM. Vérification des résultats de l'installation Vous pouvez vérifier si les pilotes MF, MF Toolbox, le manuel électronique, etc. sont installés correctement ou non selon que leurs icônes apparaissent ou pas. Pilote d'imprimante Lorsque le pilote d'imprimante est correctement installé, son icône apparaît dans le dossier des imprimantes ( Affichage du dossier des imprimantes).
Lorsque Toner Status est correctement installé, une icône Toner Status apparaît dans la barre des tâches. Si l'icône n'est pas affichée Désinstallez les pilotes ( Désinstallation des pilotes MF) et recommencez l'installation depuis le début. Autres logiciels Vous pouvez installer Presto! PageManager avec [Installation personnalisée]. Lorsque Presto! PageManager est installé correctement, une icône Presto! PageManager apparaît sur le bureau.
0LE4-006 Installation après téléchargement depuis le site Web de Canon Installez les pilotes MF ou MF Toolbox après en avoir téléchargé la dernière version depuis le site Web de Canon. Installation des pilotes MF Installation de MF Toolbox Vérification des résultats de l'installation Si vous connectez l'appareil à un ordinateur via un câble USB, installez les logiciels avant la connexion du câble USB. Aucun câble USB n'est inclus avec l'appareil. Préparez-en un acheté séparément.
8 9 10 Cliquez sur [Suivant]. Lisez attentivement le contrat de licence et cliquez sur [Oui] pour l'accepter. Sélectionnez le mode de connexion avec l'ordinateur. Connexion USB Sélectionnez [Connexion USB] et cliquez sur [Suivant]. L'installation des pilotes démarre. Passez à l'étape 17. Connexion par réseau câblé/sans fil Sélectionnez [Connexion réseau] et cliquez sur [Suivant].
Lorsque l'écran suivant apparaît, cliquez sur [Oui]. Sous Server 2003/Server 2008/Server 2008 R2/Server 2012/Server 2012 R2, cet écran ne s'affiche pas. Procédez de la façon suivante. 11 Sélectionnez l'appareil et cliquez sur [Suivant]. Si aucun appareil ne s'affiche dans [Liste des périphériques] Vérifiez la connexion de l'ordinateur et de l'appareil et les réglages de l'adresse IP (Affichage des réglages réseau (Manuel électronique)), et cliquez sur [Mettre liste des périphériques à jour].
Pour obtenir des informations sur le périphérique concernant l'utilisation d'un serveur d'impression Cochez la case [Canon Driver Information Assist Service]. 13 Sélectionnez les pilotes d'imprimante à installer et cliquez sur [Suivant]. 14 Spécifiez les détails pour chaque pilote.
[Nom de l'imprimante]/[Nom du télécopieur] Changez le nom si besoin. [Utiliser comme imprimante partagée]/[Utiliser comme télécopieur partagé] Cochez cette case si vous voulez partager l'appareil (en utilisant l'ordinateur depuis lequel vous effectuez l'installation comme serveur d'impression). Configuration du serveur d'impression (Manuel électronique) [Nom de partage] Changez le nom partagé si besoin.
6 7 8 9 10 11 Cliquez sur [Suivant]. Lisez attentivement le contrat de licence et cliquez sur [Oui] pour l'accepter. Spécifiez le dossier d'installation et cliquez sur [Suivant]. Spécifiez le dossier auquel ajouter une icône et cliquez sur [Suivant]. Cliquez sur [Démarrer]. Cliquez sur [Quitter]. Vérification des résultats de l'installation Vous pouvez vérifier si les pilotes MF sont installés correctement ou non selon que leurs icônes apparaissent ou pas.
Si l'icône n'est pas affichée Désinstallez les pilotes ( Désinstallation des pilotes MF) et recommencez l'installation depuis le début.
0LE4-007 Installation pour utiliser WSD Si vous utilisez Windows Vista/7/8/Server 2008/Server 2008 R2/Server 2012/Server 2012 R2, vous pouvez imprimer à l'aide du protocole WSD (Web Services on Devices). Si vous souhaitez utiliser le protocole WSD, commencez par installer le pilote d'imprimante, puis ajoutez une imprimante réseau. Installation des pilotes MF Ajout d'une imprimante réseau Installation des pilotes MF 1 2 3 Connectez-vous à l'ordinateur à partir d'un compte d'administrateur.
7 Cliquez sur [Parcourir]. 8 Spécifiez le dossier contenant les pilotes, sélectionnez le fichier Inf et cliquez sur [Ouvrir]. Spécifiez le dossier contenant le pilote d'imprimante comme suit. Système d'exploitation 32 bits dossiers [Driver] du CD-ROM/DVD-ROM ou du fichier téléchargé. Spécifiez [francais] [32bit] Système d'exploitation 64 bits dossiers [Driver] du CD-ROM/DVD-ROM ou du fichier téléchargé.
11 Si besoin, changez le nom de l'imprimante puis cliquez sur [Suivant]. L'installation démarre. 12 Sélectionnez [Ne pas partager cette imprimante], puis cliquez sur [Suivant]. Si vous voulez partager l'imprimante, effectuez les réglages pour le partage de l'imprimante ajoutée à l'aide de imprimante réseau. (Configuration du serveur d'impression (Manuel électronique)) 13 Cliquez sur [Terminer]. L'icône de l'imprimante installée s'affiche dans le dossier des imprimantes.
Ajout d'une imprimante réseau 1 Ouvrez le dossier réseau. Windows Vista/Server 2008 sélectionnez [Réseau]. [Démarrer] Windows 7/Server 2008 R2 [Ordinateur] sélectionnez [Réseau]. [Démarrer] Windows 8/Server 2012 Cliquez avec le bouton droit sur le coin gauche en bas de l'écran Windows 8.1/Server 2012 R2 Cliquez avec le bouton droit sur [Démarrer] 2 [Explorateur de fichiers] [Explorateur de fichiers] sélectionnez [Réseau]. sélectionnez [Réseau].
[Supprimer] cliquez sur [Oui].
0LE4-008 Désinstallation Lorsque vous n'avez plus besoin des pilotes MF, de MF Toolbox ou du Product Extended Survey Program, vous pouvez les désinstaller pour les supprimer de votre ordinateur. Désinstallation des pilotes MF Désinstallation de MF Toolbox Désinstallation du programme d'enquête étendue sur les produits Désinstallation de Toner Status Désinstallation des pilotes MF 1 2 3 Connectez-vous à l'ordinateur à partir d'un compte d'administrateur.
4 Cliquez sur [Supprimer]. 5 Cliquez sur [Oui]. La désinstallation démarre. 6 Cliquez sur [Quitter]. Désinstallation de MF Toolbox 1 2 Connectez-vous à l'ordinateur à partir d'un compte d'administrateur. Affichez [Programmes et fonctionnalités] ou [Ajouter ou supprimer des programmes].
3 Sélectionnez MF Toolbox et cliquez sur [Désinstaller] ou [Supprimer]. Le programme de désinstallation démarre. 4 5 Cliquez sur [Supprimer]. Cliquez sur [Redémarrer]. Désinstallation du programme d'enquête étendue sur les produits 1 2 3 Connectez-vous à l'ordinateur à partir d'un compte d'administrateur. Affichez [Programmes et fonctionnalités] ou [Ajouter ou supprimer des programmes].
Le programme de désinstallation démarre. 4 5 Cliquez sur [Désinstaller]. Cliquez sur [OK].
0LE4-009 Dépannage Si vous rencontrez des problèmes lors de l'installation ou la désinstallation des pilotes MF et de MF Toolbox, consultez les sections suivantes avant de contacter Canon.
0LE4-00A Annexe L'annexe comprend des informations importantes, comme l'utilisation du guide d'installation, les limites de responsabilité et les informations relatives aux droits d'auteur.
0LE4-00C Utilisation du guide d'installation Le guide d'installation est un manuel consultable sur un ordinateur. Il comprend des informations sur l'installation des pilotes. Le format électronique vous permet de trouver rapidement les pages qui vous intéressent en recherchant une rubrique ou en saisissant des motsclés. Comment rechercher le sujet qui vous intéresse Vous pouvez rechercher la page qui vous intéresse de l'une des trois façons suivantes.
0LE4-00E Configuration des écrans du guide d'installation Le guide d'installation comporte plusieurs écrans dont le contenu varie. Page d'accueil Cette page s'affiche au démarrage du guide d'installation. Logo Canon Cliquez ici sur n'importe quelle page pour retourner à la page d'accueil. Onglet [Sommaire]/Onglet [Recherche] Cliquez sur l'onglet [Sommaire] ou l'onglet [Recherche] pour afficher le menu correspondant. Sommaire Affichage des titres des chapitres ( ).
[Sommaire] Les icônes des chapitres et les titres des rubriques se trouvent dans cet onglet. / L'onglet [Sommaire] peut être élargi ou réduit à votre convenance. [Tout développer]/[Tout réduire] Cliquez sur [Tout développer] pour afficher toutes les sous-sections des rubriques. Cliquez sur [Tout réduire] pour fermer les sous-sections pour toutes les rubriques. Icônes de chapitre Cliquez sur l'icône d'un chapitre pour accéder en haut du chapitre associé.
[Saisir mot(s) clé(s) ici] Saisissez un ou plusieurs mots clés et cliquez sur pour afficher les résultats de la recherche dans une liste de résultats. Vous pouvez saisir une phrase pour rechercher les pages contenant tous les mots de cette phrase. Pour rechercher les pages contenant la phrase exacte, mettez-la entre guillemets. [Options de recherche] Cliquez ici pour indiquer les conditions de recherche telles que l'étendue de la recherche ou s'il faut respecter ou non la casse.
0LE4-00F Affichage du guide d'installation Conventions Les restrictions et les précautions liées à la manipulation de l'imprimante, les conseils pratiques et d'autres informations sont signalées de la manière suivante. Point important concernant le fonctionnement. À lire attentivement pour bien utiliser l'imprimante et éviter de l'endommager ou de causer des dommages matériels. Informations complémentaires concernant le fonctionnement ou les procédures.
0LE4-00H Autre Cette section décrit les opérations Windows de base et incluent les limites de responsabilité, les informations relatives aux droits d'auteur ainsi que d'autres informations.
0LE4-00J Fonctionnement de base sous Windows Affichage du dossier des imprimantes Activation de [Recherche du réseau] Affichage de l'écran [Installation par CD-ROM/DVD-ROM] Vérification de l'architecture en bits Affichage de [Programmes et fonctionnalités] ou de [Ajouter ou supprimer des programmes] Affichage du [Gestionnaire de périphériques] Affichage du dossier des imprimantes Windows XP Professionnel/Server 2003 [Démarrer] sélectionnez [Imprimantes et télécopieurs].
Windows Vista/7/Server 2008/Server 2008 R2 [Démarrer] saisissez "D:\MInst.exe" dans [Rechercher les programmes et fichiers] ou [Rechercher] [ENTRÉE] du clavier. Windows 8/Server 2012 Cliquez avec le bouton droit sur le coin gauche en bas de l'écran [OK]. Windows 8.1/Server 2012 R2 Cliquez avec le bouton droit sur [Démarrer] sélectionnez [Exécuter] sélectionnez [Exécuter] appuyez sur la touche saisissez "D:\MInst.exe" saisissez "D:\MInst.exe" cliquez sur cliquez sur [OK].
Windows Server 2008 [Démarrer] sélectionnez [Panneau de configuration] double-cliquez sur [Programmes et fonctionnalités]. Affichage du [Gestionnaire de périphériques] Windows XP [Démarrer] [Panneau de configuration] périphériques]. Windows Vista/7/Server 2008 R2 [Démarrer] [Panneau de configuration] [Performance et maintenance] [Matériel et audio] ou [Matériel] Windows 8/Server 2012 Cliquez avec le bouton droit sur le coin gauche en bas de l'écran [Gestionnaire de périphériques]. Windows 8.
0LE4-00K Avis Renonciation Les informations contenues dans ce document peuvent être modifiées sans avis préalable. À L'EXCEPTION DE LA GARANTIE CI-INCLUSE, CANON INC. NE FOURNIT AUCUNE AUTRE GARANTIE QUELCONQUE AVEC CETTE MACHINE, EXPLICITE OU IMPLICITE, Y COMPRIS MAIS NON LIMITÉE À TOUTE GARANTIE DE COMMERCIALISATION, DE VALEUR COMMERCIALE, D'ADÉQUATION À UN USAGE PARTICULIER OU DE CONTREFAÇON. CANON INC.