imageCLASS D320 Set-Up Sheet

ManualsBrandsCanon ManualsCopierimageCLASS D320

Thank you for purchasing the Canon imageCLASS D320.

To get your machine ready for use, please follow the instructions in this Set-Up Sheet

before referring to any other documentation.

Set-Up Sheet

Unpack the machine and its components.

Check that you have the following:

IMPORTANT

• Save your sales receipt for proof of purchase in case your machine requires warranty

service.

NOTE

•A printer cable is not included. You need a USB cable (less than 16.4ft./5m) to connect your

machine to a computer.

●

Machine

●

Canon S35 Cartridge

●

Cassette/Multi-purpose tray

●

Power Cord

●

Documentation

(Set-Up Sheet, Basic Guide, Registration Card, Limited Warranty Card)

●

CD-ROM

Summary of content (8 pages)

PAGE 1
Set-Up Sheet Thank you for purchasing the Canon imageCLASS D320. To get your machine ready for use, please follow the instructions in this Set-Up Sheet before referring to any other documentation. Unpack the machine and its components.
PAGE 2
Removing Shipping Materials 1 Place the machine on a flat surface. 2 Remove the shipping tapes on the machine and cassette/multi-purpose tray. NOTE • DO NOT remove the transparent USB label A at this stage. Transparent USB label Left side view 3 Open the platen glass cover B to remove the inner protection sheet C.
PAGE 3
Loading Paper in the Cassette 1 Load the paper stack in the cassette. • Insert the paper stack into the cassette as far as it will go. 2 Slide the width guides A and the length guide B to fit the size of the paper stack. • Adjust the guides so that there is no space between the guides and the paper. NOTE • Make sure the paper stack does not exceed the width and length guides’ claws. 3 Set the multi-purpose tray on top of the cassette.
PAGE 4
Installing the Cartridge 1 Remove the new cartridge from its protective bag. NOTE • Save the protective bag. You may need it later when you remove the cartridge. 2 Rock the cartridge 5 or 6 times to distribute the toner evenly. Instructions Drum protective shutter NOTE • Always hold the cartridge as shown so that the side with the instructions are facing upward. Do not forcefully move or push the protective shutter of the drum in any way.
PAGE 5
6 Hold the cartridge and position the arrow mark on the cartridge towards the inside of the machine shown below. 7 Align the projections A on both sides of the cartridge to the guides B in the machine (location 1) and gently slide the cartridge into the machine until the right cover slightly rises up (location 2). IMPORTANT • The right cover moves simultaneously with the action of the cartridge. Do not push the cartridge farther than location 2.
PAGE 6
Installing User Software (Windows 98/Me/2000/XP) IMPORTANT • Before you can print, you must install the user software on your computer. Screen shots in the following installation procedures are for Windows 98. 1 Make sure the USB cable is NOT connected to your machine and computer at this stage. IMPORTANT • If the Plug and Play is automatically carried out and the Found New Hardware Wizard appears, click Cancel, and follow this procedure. 2 Insert the CD-ROM into your CD-ROM drive.
PAGE 7
6 Check Install Printer Driver through a USB Connection, then click Next> . When the screen (on the upper right) appears, follow the procedure below. 6-1 Remove the transparent USB label A . 6-2 Connect the USB cable B to the machine and computer. The program will start installing the Printer Driver automatically. USB interface connection 7 When the following screen appears, select Yes, I want to restart my computer now. Then click Exit.
PAGE 8
Reading Electronic Manuals To see the guides, proceed as follows. 1 Insert the CD-ROM into your CD-ROM drive. 2 On the Windows desktop, click Start, and then Click Run... 3 In the Run dialog box, type D:\Manuals and click OK (where D: is the CD-ROM drive containing the installation disk). The Printer Guide is available in the manuals folder. NOTE • If you do not have Adobe Acrobat Reader installed on your computer, follow the procedure below to install it. 1 Insert the CD-ROM into your CD-ROM drive.