Starter Guide 1 Preface P.2 2 Installing the Machine P.4 3 Connecting to a Computer and Installing the Drivers P.12 Read this guide first. Please read this guide before operating this product. The remarks for important safety instructions are described in the Basic Operation Guide. After you finish reading the Starter Guide, store it in a safe place for future reference.
Checking the Supplied Accessories Confirm that all the supplied accessories are contained in the box. If an item is missing or damaged, please contact the Canon Authorized Service Facilities or the Canon Customer Care Center. Machine Unit Power Cord The toner cartridge is already installed. Starter Guide User Software CD-ROM Sta Limited Warranty Notice Basic Operation Guide About the USB Cable User Software CD-ROM The machine does not come with a USB cable. Have a USB cable ready as needed.
Checking the Supplied Accessories Included Documents Printed Manuals Sta Starter Guide This manual describes the configuration and software installation. This manual Basic Operation Guide This manual describes the basic use of the machine. Manuals Included in the CD-ROM e-Manual This manual explains all the features of the machine, and is categorized by subject. For details about using the e-Manual, see “Using the e-Manual” (P.18).
Removing the Packing Materials Remove all the packing materials, such as orange tape. Packing materials may change in form or placement, or may be added or removed without prior notice. 1 5 2 Check! Are all the packing materials removed? Tape Proper Handling Hold here. Hold here.
Removing the Packing Materials 3 4 Do not remove this packing material yet.
Preparing the Toner Cartridge 1 2 1 2 5 6 The plastic part is also a packing material. Be sure to remove it. 9 10 Left Side Protrusions Right Side Protrusions 2 The length of the tape is approximately 20" (50 cm). 6 1 Fit the protrusions on each side of the toner cartridge, and then slide the toner cartridge into the machine.
Preparing the Toner Cartridge 3 4 7 8 Shake 5 to 6 times. Place on a flat surface.
Loading Paper 1 2 Spread the paper guides a little wider than the width and length of the paper. 4 5 Adjust the paper guides tightly to the width and length of the paper. Loading Paper Other than Letter Size The procedure here is for loading Letter size paper. To load paper other than Letter size, such as Legal or Statement, see “Loading Paper Other than Letter Size” (P.16) after finishing the initial settings.
Loading Paper 3 Load Limit Guide Check! Push until the edge of the paper stack meets the back of the paper cassette. Make sure that the paper stack does not exceed the load limit guide. Use the paper stopper when printing. Lift the paper stopper to prevent the paper from falling out of the output tray.
Connecting the Power Cord Do not connect the USB cable. Connect the cable when installing the software. 1 2 OFF 4 Press [▲] or [▼] to highlight a language, and then press [OK]. Language English French Portuguese Spanish 7 Press [▲] or [▼] to highlight a region, and then press [OK]. Enter the date and time, and then press [OK]. 01/01/2012 12:52 AM (0:00-12:59) 5 Select Country/Region United States (US) Canada (CA) Brazil (BR) Mexico (MX) Current Time Set.
Connecting the Power Cord 3 ON 6 Press [OK]. Open frnt cover;see if orange packing material is removed. Check that tabs/tape are removed from toner cartridge. Next Next 8 Check that paper is loaded in Drawer 1. Next Configuration is finished. Copy: Press Start 100% 1 LTR Density: + -0 Original Type: Text...
Connecting to the Computer 1 USB Connection Install the software. Windows Install the MF Drivers and the MF Toolbox. Make sure that the machine is turned ON, and log on to Windows as a user with administrative privileges. Shut down all applications that are running. See the e-Manual for details about installation. Do not connect the USB cable yet. Connect the USB cable after installing the MF Drivers and the MF Toolbox.
Connecting to the Computer 2 USB Connection Windows Connect the USB cable. After installing the software, such as MF Driver, connect the USB cable. Make sure the software is installed first. Square Connector Connect to the machine. Flat Connector Connect to the computer. Computer connection via the USB is now complete.
Connecting to the Computer 1 USB Connection Install the software. Macintosh Install the MF drivers for Macintosh. It requires Mac OS X 10.5.8 version or later. The installation screen varies depending on the version of Mac OS X. This operation is for Macintosh. If using Windows, proceed to P.12 Do not connect the USB cable yet. Connect the USB cable after installing the MF Drivers and the MF Toolbox.
Connecting to the Computer 2 USB Connection Connect the USB cable. Macintosh After installing the software, such as MF Driver, connect the USB cable. Make sure the software is installed first. Square Connector Connect to the machine. Flat Connector Connect to the computer. Computer connection via the USB is now complete.
Appendix Loading Paper Other than Letter Size To load paper other than Letter size, such as Legal, see “Loading Paper” (P.8) and the following procedure after finishing the initial settings. Paper Settings MP Tray 1 Drawer 1 Load Limit Guide • Press [▲] or [▼] to highlight or , and then press [OK]. • Load the paper into the paper cassette. • Make sure that the paper stack does not exceed the load limit guides.
Appendix Loading Paper that Is Longer than the Length of the Paper Cassette Push the lower front cover and lift the front cover gently.
Appendix Using the e-Manual The e-Manual is an electronic manual document that is displayed on the computer. All features of the machine are categorized by subject, and you can quickly view the information you need by using its search function. Use the e-Manual as a reference. Click to refer to the contents, glossary, and how to use the e-Manual. Click to view precautions when using Macintosh. Enter a keyword that you want to search to quickly find the information.
Appendix Windows Installing in a Windows Environment Insert the User Software CD-ROM in your computer. Click [Custom Installation]*. Select only the [Manuals] check box. Click [Install]. Click [Yes]. Click [Exit]. Click [Next]. Click [Exit] to finish the installation. * If the CD-ROM setup screen does not appear: • Windows XP [Start] Menu → [Run] → enter [D:\MInst.exe**] → [OK] • Windows Vista/7 [Start] Menu → [Search programs and files] (or [Start Search]) → enter [D:\MInst.
Disclaimers The information in this document is subject to change without notice. CANON INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR IMPLIED, EXCEPT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR NON-INFRINGEMENT. CANON INC.
Entering Text During the setup or initial configuration, you may need to enter letters and numbers. Use [▲], [▼], [◀], [▶], numeric keys, and [OK] to enter text. OK ▼▲◀ ▶ Numeric Key Numeric Clear keys Entry Mode (See below on how to change the Entry mode) @.-_/ 2 <12> 1 ABC abc 2 DEF def 3 GHI ghi 4 JKL jkl 5 MNO mno 6 PQRS pqrs 7 TUV tuv 8 WXYZ wxyz 9 (Not available) 0 - .
Contacting the Service Center When you have a problem with your machine, refer to “Troubleshooting” in the Basic Operation Guide or the e-Manual first. If you cannot solve the problem after referring the manuals, contact the Canon Authorized Service Facilities or the Canon Customer Care Center. Canon Customer Care Center 1-800-OK-CANON (U.S.A./Canada) U.S.A Monday through Friday From 8:00 A.M. to 8:00 P.M. EST Canada Monday through Friday From 9:00 A.M. to 8:00 P.M. EST http://www.canon.ca/ CANON INC.
