<< Previous Next >> Installing Your WiFi capable imageCLASS Product to Your Network for the First Time imageCLASS MF4570dw Windows OS 1
<< Previous Next >> Installing Your WiFi capable imageCLASS Product to Your Network for the First imageCLASS MF4570dw Windows OS Before adding the machine to a wireless LAN Connection procedure Switching the connection method to wireless LAN Selecting a method for setting the wireless LAN Configuring using WPS Configuring Manually Required Information Using the Wireless Setup Assistant Checking the IP Address Installing MF Drivers and MF Toolbox 3 4 5 8 9 20 22 23 47 49 2
Before adding the machine to a wireless LAN << Previous Next >> Check to make sure that the setup of the computer and wireless LAN or access point are complete. If they are not set up, you will not be able to use the machine on the wireless LAN network even if you perform the following steps. • The structure of your computer or networked device, the existence of router functions, setting methods and security settings vary depending on your environment.
Connection procedure << Previous Next >> Once you have finished checking, connect the machine to the wireless LAN The diagram below shows the primary steps in connecting your imageCLASS device to the wireless LAN.
Switching the connection Method to Wireless LAN 1. Press [ << Previous Next >> ] (Menu). 2. Press [ ] or [ ] to select , and then press [OK]. The next screen is displayed for approximately 5 seconds. It is not necessary to turn OFF/ON the main power of the machine here. It will be done on Step 5.
Switching the connection Method to Wireless LAN << Previous Next >> 3. Press [ ] or [ ] to select
Switching the connection Method to Wireless LAN << Previous Next >> 5. Turn the machine OFF/ON when the following screen disappears. It is necessary to turn the machine OFF/ON to activate the settings. Turn OFF the machine and wait for at least 10 seconds before turning it back ON.
Selecting a method for setting the wireless LAN << Previous Next >> Two methods are provided for connecting to the wireless LAN or access point, connecting using WPS (Wi-Fi Protected Setup) function or connecting manually. Select the appropriate setting method after checking the following function on the wireless LAN or access point you are using.
Configuring with WPS Features << Previous Next >> Is there a WPS button? No Set the machine’s PIN code using “WPS PIN Code Mode” that is entered manually from the computer to the wireless LAN router or access point. Click Here YES Connect using “WPS Push Button Mode.
Configuring with WPS Features (Push Button Mode) 1. Press [ << Previous Next >> ] (Menu). 2. Press [ ] or [ ] to select , and then press [OK]. The next screen is displayed for approximately 5 seconds. You do not need to turn the machine OFF/ON in this step.
Configuring with WPS Features (Push Button Mode) << Previous Next >> 3. Press [ ] or [ ] to select , and then press [OK]. 4. Press [OK]. 5.
Configuring with WPS Features (Push Button Mode) << Previous Next >> 6. Press [ ] to select , and press [OK]. 7. Within 2 minutes, press and hold the WPS button on the wireless LAN router or access point. *The amount of time you must hold down the WPS button will depend on the wireless LAN router or access point you are using. Please refer to the instruction manual for wireless LAN router or access point. * If
Configuring with WPS Features (Push Button Mode) << Previous Next >> 8. Make sure the WiFi indicator blinks. When the wireless LAN router or access point is detected, the Wi-Fi indicator blinks. The screen below is displayed for approximately 2 seconds, and then the Wi-Fi indicator lights up.
Configuring with WPS Features (Push Button Mode) << Previous Next >> 9. Wait until the machine sets the IP address automatically (approx. 2 min). The machine sets the IP address automatically and connects to the network. When the next screen is displayed, click [OK]. If you want to set the IP address manually, see the following.
Configuring with WPS Features (Pin Code Mode) << Previous Next >> Enter the PIN code generated by the machine to wireless LAN routers and/or access points for connection. 1. Press [ ] (Menu). 2. Press [ ] or [ ] to select , and then press [OK]. 3. Press[ ] or [ ] to select , and then press [OK].
Configuring with WPS Features (Pin Code Mode) << Previous Next >> 4. Press [OK]. 5. Press [ ] or [ ] to select , and then press [OK]. 6. Press [ ] to select , and then press [OK].
Configuring with WPS Features (Pin Code Mode) << Previous Next >> 7. Within 10 Minutes, use the computer to enter the PIN code displayed on the screen into the wireless LAN router or access point. *For PIN code entry methods, see the instruction manual provided with the wireless LAN router or access point you are using. *If “Cannot find Access Point” appears, press [OK] to close the screen and follow the procedure from Step 5.
Configuring with WPS Features (Pin Code Mode) << Previous Next >> 8. Make sure the WiFi indicator blinks. When the wireless LAN router or access point is detected, the Wi-Fi indicator blinks. The next screen is displayed for approximately 2 seconds, and then the Wi-Fi indicator lights.
Configuring with WPS Features (Pin Code Mode) << Previous Next >> 9. Wait until the machine sets the IP address automatically (approx. 2 min). The machine sets the IP address automatically and connects to the network. If you want to set the IP address manually, see the following.
Configuring Manually << Previous Next >> If your wireless LAN routers and/or access points do not support WPS, enter the wireless LAN router and/or access point information to the machine for connection. Select Access Point From the list of access points searched by the machine, select a wireless LAN router or an access point to be connected and enter a network key for connection. If you know your SSID and Network Key Click Here.
Configuring Manually << Previous Next >> Preparing The following information is required. Check your wireless LAN routers and/or access points, and make a note of the information labeled on the bottom. * See the manual provided with your wireless LAN routers and/or access points, or contact the manufacturer for where the information is displayed or how to check it.
Configuring Manually (Required Information) << Previous Next >> Access Point Name/Network Name * It may be labeled as “SSID.” It is the distinguished name for specifying a particular access point. It is used for selecting an access point. Network Key *It is also called encryption key, WEP key, WPA/WPA2 passphrase, PSK or pre-shared key. It is a password that must be set in order to prevent communications from being intercepted. It is used for entering the network key.
Configuring Manually (Using the Wireless Setup Assistant) << Previous Next >> Checking the SSID or Network Key of the Wireless LAN Router/Access Point If the SSID and network key are not indicated on the body of the wireless LAN router or access point or if you are not sure because they are changed, you can check using Canon MF/LBP Wireless Setup Assistant. * Canon MF/LBP Wireless Setup Assistant is included in the supplied User Software CD-ROM. 1. Check your network environment.
Configuring Manually (Using the Wireless Setup Assistant) << Previous Next >> 3. Click [Additional Software Programs].
Configuring Manually (Using the Wireless Setup Assistant) << Previous Next >> 4. Click [Start] for [Canon MF/LBP Wireless Setup Assistant].
Configuring Manually (Using the Wireless Setup Assistant) << Previous Next >> 5. Read the License Agreement. If you agree, click [Yes]. 6. The information for the wireless LAN router or access point is displayed. Write down the information outlined in orange.
Configuring Manually (Using the Wireless Setup Assistant) << Previous Next >> If multiple access points are displayed Write down all of the displayed SSIDs When wireless LAN routers or access points are not displayed Click [Refresh] When information is not displayed even after clicking [Refresh], check that the settings for the computer and wireless LAN or access point are complete. Click Here to return to the selection page.
Configuring Manually (Selecting Access Points) << Previous Next >> From the list of access points searched by the machine, select a wireless LAN router or an access point to be connected and enter a network key for connection. Selecting Access Point For selecting access points, WEP 802.11 authentication system is set to , while WPA/WPA2 is set to Auto> (either AES-CCMP or TKIP) 1. Press [ ] (Menu). 2. Press [ ] or [ ] to select , and then press [OK].
Configuring Manually (Selecting Access Points) << Previous Next >> 3. Press [ ] or [ ] to select , and then press [OK]. 4. Press [OK]. 5. Press [ ] or [ ] to select , and then press [OK].
Configuring Manually (Selecting Access Points) << Previous Next >> 6. Press [ ] or [ ] to select
Configuring Manually (Selecting Access Points) << Previous Next >> 7. Press [ ] or [ ] to select the matched SSID that you have written down earlier using, and then press [OK]. If multiple matched SSID are displayed, select the one that is displayed at the top (a stronger signal).
Configuring Manually (Selecting Access Points) << Previous Next >> 8. Press [ ] or [ ] to select entry format that matches the number of network key characters (digits) that you have written down earlier, and then press [OK]. Either of the following screens is displayed.
Configuring Manually (Selecting Access Points) << Previous Next >> 9. Enter the network key that you have written down. ASCII text 1. Press [ ] (Tone), and the select . 2. Enter the network key. Enter it using the numeric keys. 3. Press [ ] or [ ] to select , and then press [OK]. Hexadecimal 1. Enter the network key. Select the characters using [ ] or [ ], and then press [OK] to enter. 2. Press [ ] or [ ] to select using , and then press [OK].
Configuring Manually (Selecting Access Points) << Previous Next >> 10. Press [ ] to select , and then press [OK].
Configuring Manually (Selecting Access Points) << Previous Next >> The Wi-Fi indicator blinks. The screen below is displayed for approximately 2 seconds, and then the Wi-Fi indicator lights up. * When a message appears, press [OK] to close the screen and start the procedure from Step 4.
Configuring Manually (Selecting Access Points) << Previous Next >> 11. Wait until the machine sets the IP address automatically (approx. 2 min). The machine sets the IP address automatically and connects to the network. If you want to set the IP address manually, see the following.
Configuring Manually (Manually Entering SSID) 1. Press [ << Previous Next >> ] (Menu). 2. Press [ ] or [ ] to select , and then press [OK]. 3. Press [ ] or [ ] to select , and then press [OK]. 4. Press [OK].
Configuring Manually (Manually Entering SSID) << Previous Next >> 5. Press [ ] or [ ]to select , and then press [OK]. 6. Press [ ] or [ ] to select , and then press [OK]. 7. Enter the SSID that you have written down. After entering it using the numeric keys, select using [ ] or [ ], and then press [OK].
Configuring Manually (Manually Entering SSID) << Previous Next >> 8. Press [ ] or [ ] to select encryption types that you have written down, and then press [OK]. In case of , go to step 12. 9. Press [ ] or [ ] to select the authentication method or encryption type that you have written down, and then press [OK]. When the type of encryption is WEP 1. Press [ ] or [ ] to select the authentication method, and then press [OK].
Configuring Manually (Manually Entering SSID) 2. Press [ ] or [ << Previous Next >> ] to Select , and then press [OK]. 3. Press [ ] or [ ]to select the WEP key using, and then press [OK]. * Select the key number to be used for encryption that you wrote down earlier.
Configuring Manually (Manually Entering SSID) << Previous Next >> 10. Press [ ] or [ ] to select the entry format that matches the number of network key characters (digits) that you have written down, and then press [OK]. Either of the following screens is displayed.
Configuring Manually (Manually Entering SSID) << Previous Next >> 11. Enter the network key that you have written down. ASCII text 1. Press [ ](Tone), and then select . 2. Enter the network key, using the numeric keys. 3. After entering, press [ ] or [ ] to select , and then press [OK]. • When WEP is the encryption type Select WEP keys (1 to 4) for encryption. 1. Press [ 2. Press [ ] or [ ] or [ ] to select
Configuring Manually (Manually Entering SSID) << Previous Next >> Hexadecimal 1. Enter the network key. *Press [ ] or [ ] to select the character, and then press [OK] to enter. 2. After entering, press [ ] or [ ] to select , and then press [OK]. • When WEP is the encryption type Select WEP keys (1 to 4) for encryption 1. After entering the network key, press [ ] or [ ] to select
Configuring Manually (Manually Entering SSID) << Previous Next >> 12. Press [ ] to select , and then press [OK]. The Wi-Fi indicator blinks.
Configuring Manually (Selecting Access Points) << Previous Next >> The screen below is displayed for approximately 2 seconds, and then the Wi-Fi indicator lights up. * When one of the following messages appears, press [OK] to close the screen and check to make sure that the type of encryption, the authentication method or encryption method, the network key are correctly entered. If not, enter the network key again.
Configuring Manually (Manually Entering SSID) << Previous Next >> 13. Wait until the machine sets the IP address automatically (approx. 2 min). The machine sets the IP address automatically and connects to the network. If you want to set the IP address manually, see the following.
Checking IP Address Settings << Previous Next >> Follow the steps below to confirm the IP address set on the machine. Write down the IP address as you may need it when installing the software. Checking IPv4 address settings 1. Press [ ] (Status Monitor/Cancel). 2. Press [ ] or [ ] to select , and then press [OK]. 3. Press [ ] or [ ] to select , and then press [OK].
Checking IP Address Settings 4. Press [ ] or [ << Previous Next >> ] to select , and then press [OK]. 5. Write down the IP address. 6. Press [ ] (Status Monitor/Cancel) to close the screen. *If you are using IPv6, please see the e-Manual for instructions on checking the IP address.
Installing the MF Drivers and MF Toolbox << Previous Next >> *When you are in an IPv6 environment, you may not be able to use the installation procedure below to install the MF drivers. See “Installing the MF Drivers on the WSD Network” to install the MF Drivers. *Note that you cannot use the scan functions in an IPv6 environment. To install the Presto! PageManager or e-Manual please see “Installing using [Custom Installation]” in the e-Manual. 1.
Installing the MF Drivers and MF Toolbox << Previous Next >> 2. Click [Easy Installation].
Installing the MF Drivers and MF Toolbox << Previous Next >> 3. When the following screen appears, select [Next] for [Connect Printer to a computer via Network.
Installing the MF Drivers and MF Toolbox << Previous Next >> 4. Click [Install].
Installing the MF Drivers and MF Toolbox << Previous Next >> 5. Read the License Agreement and click [Yes].
Installing the MF Drivers and MF Toolbox << Previous Next >> 6. Click [Next]. The following screen appears. Click [Yes].
Installing the MF Drivers and MF Toolbox << Previous Next >> 7. Select the device to be installed. (1) (2) Select the device. Click [Next]. When no devices are displayed in [Device List] Try the following procedure. 1. Check the following. • The computer and machine are connected over the network. • The device for wireless LAN connection and the access point are connected. • The machine is turned ON.
Installing the MF Drivers and MF Toolbox << Previous Next >> If the problem persists, try the following procedure. 1. Click [Search by IP Address]. 2. Enter the IP address of the machine. *If the IP address of the machine is set between "169.254.1.0 and 169.254.254.255", it means that the IP address is automatically assigned to the machine in the auto configuration procedure. When the IP address is not a link-local address, set up your computer and the machine to be on the same subnet.
Installing the MF Drivers and MF Toolbox << Previous Next >> 8. Click [Start] to begin installation. 9. Click [Exit].
Installing the MF Drivers and MF Toolbox << Previous Next >> 10. Click [Start]. 11. Click [Exit].
Installing the MF Drivers and MF Toolbox << Previous Next >> 12. Confirm that the applications are selected [ ] under [Install] and click [Next].
Installing the MF Drivers and MF Toolbox << Previous Next >> 13. Restart your computer. 1. 2. Select the [Restart Computer Now (Recommended)] check box. Click [Restart]. * The CD-ROM can be ejected once this screen appears.
Congratulations! << Previous Next >> You have successfully added your Canon imageCLASS device to your wireless network.
