Contents Back Next Page Cover Introduction Contents Chapter 1 Before Using the Scanner User Manual Chapter 2 Setup Chapter 3 Basic Operation Chapter 4 CaptureOnTouch Settings Chapter 5 Other Scanning Methods Chapter 6 Scanner Driver Settings Chapter 7 Maintenance Chapter 8 Troubleshooting Chapter 9 Appendix ♦ Please read this manual before operating this scanner. ♦ After you finish reading this manual, store it in a safe place for future reference.
Contents International ENERGY STAR® Office Equipment Program As an ENERGY STAR® Partner, Canon Electronics Inc. has determined that this machine meets the ENERGY STAR® Program guidelines for energy efficiency. The International ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the use of computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption.
Back Contents Introduction Thank you for purchasing the Canon DR-2010C/DR-2510C/DR-2010M/DR-2510M Document Scanner. Please read this manual thoroughly before using the scanner to familiarize yourself with its capabilities, and to make the most of its many functions. After reading this manual, store it in a safe place for future reference. Previous Page Next Page Contents Introduction ...............................................................................3 Symbols Used in This Manual.............
Contents 7. Other Functions ......................................................................................... 32 Setting the Long Document Mode ........................................................ 32 Chapter 4 CaptureOnTouch Settings ................................................ 35 1. What is CaptureOnTouch?......................................................................... 35 2. Starting CaptureOnTouch ..........................................................................
Contents 4. Uninstalling the Software......................................................................... 110 Uninstalling on Windows .................................................................... 110 Uninstalling on Mac OS X ................................................................... 112 Chapter 9 Appendix .................................................................. 113 Specifications......................................................................................
Contents Back Previous Page Next Page 1. Important Safety Instructions Chapter 1 Before Using the Scanner 1. Important Safety Instructions ...................................................... 6 Installation Location ............................................................................... 6 AC Adapter ............................................................................................. 7 Moving the Scanner ...............................................................................
Contents • • • Avoid exposing the scanner to rapid changes in temperature. If the room in which the scanner is installed is cold but rapidly heated, water droplets (condensation) may form inside the scanner. This may result in a noticeable degradation in scanning quality. The following conditions are recommended for optimal scanning quality: - Room temperature: 10 °C to 32.5 °C (50 °F to 90.5 °F) - Humidity: 20% to 80% RH Avoid installing the scanner near equipment that generates a magnetic field (e.g.
Contents Handling WARNING Note the following precautions whenever using the scanner. Failure to do so may result in a fire or electric shock. • • • • • • • • • • • • • 8 Never use alcohol, benzene, paint thinner, aerosol sprays, or any other highly flammable substance near the scanner. Do not cut, damage, or modify the power cord. Do not place heavy objects on the power cord, and do not pull or excessively bend the power cord. Never connect the power cord when your hands are wet.
Contents Back Previous Page Next Page Disposal 2. Features of the Scanner • The main features of the document scanner are described below. When disposing of this scanner, be sure to follow all local ordinances and laws or consult with the retailer who sold you the scanner. Compact Size When sending the scanner for repairs • When a request is made for repairs, the scanner needs to be sent to the specified address. When sending the scanner, use the packing box in which it came.
Contents Auto Color Detection The scanner detects whether the scanned document is in color or black and white, and saves the image accordingly. Back Previous Page Next Page Sleep Mode The scanner is designed to save energy by entering the sleep mode when it is not scanning documents. Folio Scan You can scan folded documents. The scanner will scan both sides and combine the scanned images into a single image.
Contents Back Previous Page Next Page Back View 3. Names and Functions of Parts This section describes the name and function of each part. Make sure to read this section and familiarize yourself with the parts of the scanner before using the scanner. Front View/Right-Side View Document Feed Tray Open to place documents. (See p.23) Job Buttons These buttons can perform user-specified functions assigned with the Capture OnTouch. (See p.36) Document Eject Area Scanned documents are output here.
Contents Back Previous Page Next Page 1. Scanner System Requirements Chapter 2 Setup To use the scanner, your computer must satisfy the following system requirements. System requirements for Windows 1. Scanner System Requirements ................................................... 12 • 2. Installing the Software ............................................................. 13 Setup Disc ............................................................................................
Contents Back Previous Page Next Page 2. Installing the Software • • • • • • • • 13 IMPORTANT If you do not know the requirements for your computer system, contact the store where you purchased the computer or the manufacturer of the computer for more information. This section describes how to install the required software. Setup Disc If you use the scanner with Windows, use the latest USB 2.0 driver made available by Microsoft. For details, consult your local authorized Canon dealer.
Back Contents Software Installation (Windows) Follow the procedure below to install the software. • • • 4 Click [Install]. 5 Click [Next]. 6 Read the license agreement → click [Yes] to accept it. IMPORTANT Install the software before connecting the scanner to the computer. Log on to Windows as an Administrator. Close all other applications before installing the software. 1 2 3 Turn the power of the computer ON. Insert the Setup disc into the CD-ROM drive of the computer.
Back Contents 15 Previous Page Next Page 7 When the driver installation is complete, click [Finish]. 10 Confirm the installation location → click [Next]. 8 Click [Next]. 11 When the CapturePerfect 3.0 installation is complete, click [Finish]. 9 Read the license agreement → click [Yes] to accept it. 12 Click [Next].
Contents 13 16 When the User Manual installation is complete, click [Finish]. Back Previous Page Next Page Software Installation (Mac OS X) Follow the procedure below to install the software. 14 Click [Exit] to finish installing the software. 15 Remove the Setup disc from the CD-ROM drive. 1 2 3 4 Turn the power of the computer ON. Insert the Setup disc into the CD drive. Click [DR-2510M Installer]. Click [Continue].
Contents 17 Back Previous Page Next Page 5 Read the license agreement and click [Continue] to accept it. 8 Click [Upgrade]. 6 Click [Agree]. 9 When the confirmation screen appears, enter the password of a user with administrator rights, and then click [OK]. 7 Click [Continue]. 10 When the installation is complete, click [Close].
Contents Third-Party Software The following software is included on the Setup disc. For details on operating the software, refer to the Help for each software. • • Presto! BizCard Business card management software from NewSoft Technology Corp. Run the following installer from the Setup disc to install. BizCard/BCRInstaller Presto! PageManager Photo and document management software from NewSoft Technology Corp. Run the following installer from the Setup disc to install.
Contents 3 Connect the plug of the AC adapter to the power connector on the back of the scanner. Back Previous Page Next Page 3. Turning the Power ON When you turn the computer and the scanner ON for the first time, the Plug and Play function of Windows recognizes the scanner and automatically installs the required device driver. • • IMPORTANT If you turn the power OFF, wait at least 10 seconds before turning it ON again.
Contents 3 The scanner is automatically recognized as new hardware. In Windows, a balloon message such as shown below appears on the task bar. Simply wait a while, until the scanner is recognized automatically. When the scanner is properly connected to the computer, the (CaptureOnTouch) icon appears on the taskbar (or menu bar) as follows. Windows taskbar Mac OS X menu bar If the taskbar icon appears as , the scanner is not properly connected to the computer.
Contents Back Previous Page Next Page 1. Documents Chapter 3 Basic Operation 3. Placing Documents ................................................................. 24 Plain Paper Size Width: 1.97" to 8.5" (50 mm to 216 mm) Length: 2.12" to 14.02" (53.9 mm to 356mm)* Paper weight: (Page separation mode) 14 to 32 lb bond (52 to 128 g/m2) 0.0024" to 0.0059" (0.06 mm to 0.15 mm) Paper weight: (Bypass mode) 11 to 42 lb bond (40 to 157 g/m2) 0.002" to 0.0079" (0.05 mm to 0.
Contents IMPORTANT A document must meet the following criteria to be scannable: • • • • • • • Scanning documents before the ink is dry can cause problems with the scanner. Always make sure that the ink on a document is dry before scanning it. Scanning documents that are written in pencil or similar material may make the rollers and scanning glass dirty, which can lead to smudges on the scanned image and transfer the dirt to subsequent documents.
Contents Back Previous Page Next Page 2. Preparing the Scanner Prepare the document feed tray according to the paper size and type. Preparing the Document Feed Tray • • • NOTE Documents can be scanned with the document eject tray closed. Open the document eject tray when you want to stack output documents. Use the extension tray when the document hangs over the edge of the main tray. Open the document feed tray.
Back Contents 3. Placing Documents There are two methods for feeding documents, the Page Separation mode and Bypass mode. Feeding pages continuously from a stack of documents placed in the feed tray is called the Page Separation mode. Feeding documents one sheet at a time or feeding documents consisting of multiple pages that are attached, is called the bypass mode. The document feed method can be changed by moving the feed selection lever.
Contents 5 • • NOTE Before scanning, make sure that the document is not curled or creased, and that it is placed in the feed tray correctly. Scanning an improperly placed, curled, or creased document may damage the document or cause a paper jam. 25 Previous Page Next Page Adjust the document guides to fit the width of the document. • 6 Back Use the application software to start scanning.
Back Contents Feeding in the Bypass Mode When scanning multiple page documents that are fastened together, such as invoices, place the documents so that the edge that is fastened together is facing down. 1 Switch the feed selection lever to (Bypass). 4 Previous Page Next Page Use the application software to start scanning. IMPORTANT After you finish scanning, close the document feed tray and the document eject tray to prevent damage to the scanner while it is not being used.
Contents 3 Place the card horizontally, with the reverse side facing you, and the top of the card facing down. Back Previous Page Next Page Placing Folded Documents Folio Scan enables you to scan documents that are larger than LTR/A4 and therefore do not fit in the feeder. (The maximum size is 11" X 17"/A3.) To use the function, fold the document in half lengthwise and place it into the feeder. The DR-2010C/DR-2510C will scan both sides and combine the scanned images into a single image.
Contents Back Previous Page Next Page 4. Scanning Methods • • • • NOTE When scanning folded documents, switch the feed selection lever to (Bypass). When placing folded documents, place the document into the scanner so that the fold is on the right side. The side of the folded document facing you will become the right side of the combined image. When scanning a folded document, set [Scanning Side] on the scanner driver settings screen to [Folio]. (See "Scanning Side Settings" on page 69.
Contents • CapturePerfect 3.0 (Windows only) This is scanning application for advanced users. It offers a variety of scanning methods and functions for editing the scanned image. Back Previous Page Next Page 5. Practical Examples This section provides examples of settings when scanning. Refer to these examples when specifying ISIS/TWAIN driver settings. For descriptions of particular setting items, see "Chapter 6 Scanner Driver Settings," on p. 60.
Contents • • To create separate files for each batch of documents during continuous scanning Select the [Feeding Option] by clicking [Automatic Feeding] or [Panel-Feeding] and set [Batch separation] to [Auto].This function is available only under Windows when the scanner driver was called from an ISIS compatible application. To scan a batch of documents one page at a time Set [Feeding Option] to [Automatic Feeding] or [Panel-Feeding] and scan each document separately.
Contents 3 6. Clearing a Paper Jam Back Previous Page Next Page Remove the jammed document from the document feeding side or document ejecting side. When paper jams occur during scanning, use the following procedure to clear them. CAUTION When removing jammed paper, take care not to cut your hands on the edges of the paper. 1 Remove any documents that have been left in the eject tray. IMPORTANT Make sure to pull the document out carefully, without applying too much force.
Contents Back Previous Page Next Page 7. Other Functions • • NOTE After removing the jammed paper, check to see if the last page was scanned correctly, and then continue scanning. If a paper jam occurs when [Rapid recovery system] is enabled in the scanner driver setting screen, the image data of the document is not saved and operation is interrupted. This allows you to continue scanning from the document that caused the paper jam after the paper jam is fixed.
Back Contents 2 3 Double-click [Scanners and Cameras]. Right-click [CANON DR-2010C USB] or [CANON DR-2510C USB] → click [Properties]. Previous Page Next Page 4 Click the [Maintenance] tab → [Long Document Mode (1,000 mm)]. 5 Click [Apply] → [OK]. 6 Turn the scanner OFF and then ON again. Setting procedure under Mac OS X 1 33 Start Image Capture. To start Image Capture, click the hard disk icon (e.g. [Macintosh HD]), the [Applications] folder, and then the [Image Capture] icon.
Contents 5 Click [DR-2510M TWAIN] in the [Devices] menu. 6 Click [Scan]. The settings screen for the scanner driver appears. 7 Click the (information) button. The [Scanner Information] dialog box appears. 8 Click [Maintenance]. The [Maintenance] dialog box appears. 9 10 34 Click [Long document (1000mm)]. Click to close the dialog box.
Back Contents Previous Page Next Page 1. What is CaptureOnTouch? Chapter 4 CaptureOnTouch Settings CaptureOnTouch is a scanning application that allows you to scan documents using easy-to-follow on-screen instructions. Save to folder Save to a specified folder. Print Print to a specified printer. 1. What is CaptureOnTouch? ......................................................... 35 2. Starting CaptureOnTouch .......................................................... 36 Quitting CaptureOnTouch .......
Contents Select Scan Job Back Previous Page Next Page 2. Starting CaptureOnTouch CaptureOnTouch resides on your system when you start your computer, and a CaptureOnTouch icon appears on the taskbar (menu bar in Mac OS X) (default). When you click (CaptureOnTouch) on the taskbar (menu bar in Mac OS X) and click [Launch CaptureOnTouch] in the menu that appears, the CaptureOnTouch main screen appears.
Contents Quitting CaptureOnTouch Click (CaptureOnTouch) on the taskbar (menu bar in Mac OS X), and click [Exit] in the menu. Back Previous Page Next Page 3. Scanner Settings Configure various scan settings such as the scanning method and document size (collectively referred to as “scanner settings”). [Scan First] and [Select Scan Job] share the same scanner setting items. For [Scan First] The application no longer resides on the system, and the taskbar (menu bar in Mac OS X) icon disappears.
Contents For [Select Scan Job] Back Previous Page Next Page Basic Scanner Settings Configure the basic setting items for the scanner. Configurations from the driver settings screen are used for setting items that are not included in the basic setting items. [Color mode] Select from the following modes for scanning documents. [Auto Color Detection] Automatically detects whether a document is color or black and white, and scans. [24-bit Color] Scans the document in color.
Contents [Text orientation recognition] The orientation of text in scanned images is detected, and the images are rotated to match the orientation of the text. [Use advanced settings dialog box] Scanner settings other than the basic settings are configured in the driver settings screen. To open the driver settings screen, select the [Use advanced settings dialog box] check box and click the [Open] button. Back Previous Page Next Page 4.
Contents [[Print] Print scanned images to a specified printer. When this method is selected, you must specify the printer to which images will be printed. Back Previous Page Next Page 5. Scan First Operation Flow Scan document ▼ Select output method ▼ Configure output settings ▼ Output scanned images [Send to application] Open scanned images with a specified application.
Back Contents 3 Previous Page Next Page When scanning is finished, the [Output method] screen appears in the main window. Click [Scanner setting] to display the [Scanner setting] dialog box, and configure the scanner settings. NOTE If the [Enable continuous scanning] check box was selected, a message asking whether to continue scanning another document appears when the initial scan is finished. Load the next document into the scanner, and click the [Continue scanning] button.
Contents 6 Configure settings for the output method, and click the output button to output the scanned images. Back Previous Page Next Page 6. Select Scan Job Operation Flow Register jobs ▼ Select job ▼ Scan document ▼ Output scanned images The name of the output button differs depending on the selected output method. If you select [Save to folder] for the output method, for example, the output button appears as [Save]. The completion screen appears after the scanned images are output.
Contents 2 Back [Output settings] tab Configure settings for the output method. The items that appear in this tab differ depending on the [Output method] selected. Click the [Register new job] button. The [Register new job] dialog box appears. [Scanner setting] tab Configure scan conditions. NOTE If you select a registered job and click [Job list/edit], the [Job editing] dialog box appears allowing you to edit the settings of the selected job. 3 Configure the job settings.
Contents [Button assignment] tab Configure settings to assign the job to a job button on the scanner. If [Assign scanner button 1 to Scan First] is selected in the main screen, assignment to job button 1 is not available. 4 Back Previous Page Next Page Selecting Scan Jobs 1 2 Place the document in the scanner. Click the [Select Scan Job] tab. Click the [OK] button. The main screen for [Select Scan Job] appears.
Back Contents • • NOTE If the [Confirm output] check box is selected, you can confirm output settings after scanning. If the [Enable continuous scanning] check box is selected, you can continue scanning after all the pages of a document are scanned. 4 Click the [Start] button. • • Previous Page Next Page NOTE Click [Return to main screen] to return to the main screen of [Select Scan Job].
Contents Back Previous Page Next Page 7. Scanning with the Job Buttons 8. Environmental Settings Under default settings, [Scan First] and [Select Scan Job] are pre-assigned to the three job buttons on the scanner. To configure environmental settings for CaptureOnTouch, click the [Environ. Settings] button in the main screen and open the [Environmental settings] dialog box.
Contents [Basic settings] Tab The [Basic settings] tab allows you to configure the following settings. Back Previous Page Next Page [Restore] button Restore configurations from previously backed up registry files. When using multiple scanners, you can back up the environmental settings on one scanner, and restore those settings on another scanner to copy the settings.
Contents [Maximum size of attached file] If the [Display confirmation message if file size exceeds the above] check box is selected and an attached file exceeds the size limit, a confirmation message will appear. • • 48 When using [Scan First], the confirmation message will appear after the entire document is scanned. When using [Select Scan Job], the confirmation message will appear if the file size exceeds the set limit during scanning.
Back Contents Previous Page Next Page 1. Scanning with CapturePerfect 3.0 Chapter 5 Other Scanning Methods CapturePerfect 3.0 is an ISIS-compliant application developed for Canon document scanners. For more information on CapturePerfect 3.0, refer to the CapturePerfect 3.0 Operation Guide. 1. Scanning with CapturePerfect 3.0................................................ 49 2. Basic Scanning Procedure......................................................... 50 3. Using the Scan Panel .................
Contents Scan Batch to File Documents are scanned with preset scanning conditions, and the scanned image data is saved to a specified folder. Scan Batch to Printer Documents are scanned with preset scanning conditions, and the scanned image data is printed to a specified printer. Scan Batch to Mail Documents are scanned with preset scanning conditions, and a MAPI-compliant email client is started to generate a new e-mail message with the scanned images as attachments. Back 2.
Contents 2 From the [Scan] menu, select [Select Scanner]. 5 6 Back Previous Page Next Page Click [OK] to finish Scanner Selection. From the [Scan] menu, select [Scan Batch to File]. The [Select Scanner] dialog box appears. 3 Select your scanner name → click [OK]. The [Scan Batch to File Setting] dialog box appears. 7 Click [Scanner Setting], and configure the scanner settings. The [Configure Device Setlings] dialog box appears.
Back Contents • 8 9 Specify the file name and format for the image file to be saved. For details on other settings in the [Scan Batch to File Setting] dialog box, see the CapturePerfect 3.0 Operation Guide. Place the documents into the scanner, and click [Save] to start scanning. IMPORTANT Depending on the [Feeding Option] setting of the scanner driver, place your documents as follows: • 52 scanning.
Back Contents 12 When scanning is complete, select [Exit] from the [File] menu to quit CapturePerfect. Previous Page Next Page NOTE The following jobs are already registered to job numbers 01 and 02. Job Number Registering Scan Jobs and Scanning Job Title Job Type 01 Color Document ScanToPC 02 Binary Document ScanToPC 2 Select a job number to register ([No.]), and click [Create/Edit]. The [Create/Edit] dialog box appears. 3 Enter the job title.
Back Contents [Scan To Mail]: Specify the file name and format for the image file to be attached to the e-mail message. [Scan To Mail]: Attaches scanned images to an e-mail message and sends it. [Scan To Print]: Prints scanned images to a specified printer. 5 Previous Page Next Page Click [Detail Settings]. A settings dialog box based on the specified function appears. [Scan To PC]: Specify the file name, format, and destination for the image file to be saved.
Back Contents 7 • • • Click [OK] to close the [Register/Edit/Delete] dialog box. NOTE Previous Page Next Page 3. Using the Scan Panel If Feeding Option in the scan settings is set to [Panel-Feeding] or [Automatic Feeding], the Scan Panel will appear when you start scanning. You can register up to 99 jobs. To edit the settings of a registered job, select the job and click [Create/Edit]. b To delete a registered job, select the job to delete and click [Delete].
Contents Back Previous Page Next Page 4. Special Scanning NOTE When you open the scanner driver in Windows, the Scan Panel icon appears on the taskbar. You can open the Scan Panel by double-clicking the icon. This section describes examples of settings that can be specified when scanning with the scanner. For more information, see Chapter 6, "Scanner Driver Settings," or the Online Help.
Contents Back Previous Page Next Page Scanning Different Sized Documents Together Skipping Blank Pages You can set the scanning conditions to scan different sized documents, such as LTR and LGL (A4 and B5) documents, together, while detecting the correct size of the document. Set [Mode] on the scanner driver Settings screen to [Advanced Text Enhancement] (only for Windows) or [Advanced Text Enhancement II].
Contents Deskewing Documents Back Previous Page Next Page Reducing Bleed Through for Thin Documents and Documents with Dark Reverse Sides You can set the scanning conditions to detect slanted document pages and straighten the scanned images. Select the [Deskew] check box on the scanner driver settings screen. For more information on setting the scanning conditions, see Chapter 6, "Scanner Driver Settings - Correcting Image Skewing.
Contents Creating Smaller Files You can set the scanning conditions to save the scanned image as a PDF file with a high compression rate, so that the file size is smaller. Select the [PDF] file format in the output settings, and set [Compression mode] to [High Compression] in the [Detail Settings]. You can also select the [JPEG] file format, and set a high compression ratio in the [Detail Settings].
Contents Back Previous Page Next Page 1. Before Using the Scanner Chapter 6 Scanner Driver Settings 1. Before Using the Scanner ......................................................... 60 To use the scanner with an ISIS-compliant application (only for Windows) or TWAIN-compliant application, the scanner must first be selected as the scanner to be used. Scanner selection under Windows 2. Scan driver settings ................................................................ 62 Scan Mode Settings ......
Back Contents 3 Select [Canon DR-2510C] or [Canon DR-2010C] → click [OK]. Previous Page Next Page Scanner selection under Mac OS X As an example, the following explanation describes the procedure when using Image Capture, a standard-installed application for Mac OS X. 1 Start Image Capture. To start Image Capture, click the hard disk icon (e.g. [Macintosh HD]), the [Applications] folder, and then the [Image Capture] icon.
Contents 5 Select [DR-2510M TWAIN] from the [Devices] menu. Back Previous Page Next Page 2. Scan driver settings This section describes the various settings that can be made from the scanner driver settings screen. Scanner driver settings screen under Windows 6 Click [Scan]. The ISIS/TWAIN driver properties dialog box is displayed when you select [Scanner Setting] on the [Scan] menu of CapturePerfect 3.0.
Contents NOTE If you are using a TWAIN driver, the two extra settings below are displayed on the [Basic] tab and [Image processing] tab. Refer to the Help for details. -[Basic] tab: Scan options -[Image processing]: Black/white reversion Scanner driver settings screen under Mac OS X The Scanner driver settings screen under Max OS X has a Simple Mode and an Advanced Mode. (In the default condition after installation of the scanner driver, the screen will open in Simple Mode.
Back Contents Scan Mode Settings This section describes the procedure for setting the scan mode to suit your needs. Under Windows 1 64 In the ISIS/TWAIN driver properties dialog box, click the [Basic] tab → select the scanning mode from the [Mode] drop-down list. Previous Page Next Page Under Mac OS X 1 Select a suitable setting for [Mode]. (This is the same in Simple Mode and Advanced Mode.
Contents NOTE - [256-level Gray] Scans documents containing photos as grayscale images. Color - [24-bit Color] Scans documents containing color photos as full-color images. Auto Color Detection - 65 [Auto Color Detection] Whether a document is black-and-white or color is detected before the scanned image is saved.
Back Contents Auto Color Detection This section describes the procedure for setting the scanner to automatically detect whether a document is in color or black-and-white when scanning. Previous Page Next Page Under Mac OS X 1 Select [Auto Color Detection] for [Mode]. 2 In Advanced Mode, when [Auto Color Detection] is selected for [Mode], various items can be set on the screen.
Back Contents Previous Page Next Page Paper Size Settings • NOTE The settings you can specify are as follows. - [Color Saturation/Proportion of Color] Normally scan with the default values (Color Saturation: 2, Proportion of Color: 2), but change the settings when you want to scan a color document as a blackand-white document. y Color Saturation: change the setting towards "High" when you want to scan a color document with low color saturation as a black-and-white document.
Back Contents Under Mac OS X 1 Scan Resolution Settings This section describes the procedure for setting the resolution for scanning. Select [Auto-detection] for [Page Size]. (This is the same in Simple Mode and Advanced Mode.) Under Windows 1 • • • 68 Previous Page Next Page NOTE Click [Auto-detection] to scan the following kinds of documents. - Documents of undetermined size - Documents including mixed page sizes - When using the Long Document mode (See "Setting the Long Document Mode," on p.
Back Contents Under Mac OS X 1 Select a suitable resolution setting for [Dots per inch]. (This is the same in Simple Mode and Advanced Mode.) Previous Page Next Page Scanning Side Settings This section describes the procedure for setting the page side settings for scanning. Under Windows 1 • • 69 NOTE Higher resolutions provide clearer images, but produce larger files.
Contents Under Mac OS X 1 Select a suitable setting for [Scanning Side]. (This is the same in Simple Mode and Advanced Mode.) Back Previous Page Next Page - [Skip Blank Page] As each document page is scanned, the scanner detects whether it is blank, and if so, the image is not saved. y Under Windows, selecting [Skip Blank Page] enables the [Setting] button, which opens the [Blank Skip Setting] dialog box. Under Mac OS X, selecting [Skip Blank Page] opens the content density setting screen.
Back Contents Correcting Image Skewing This section describes the procedure for setting the scanner to detect slanted document pages and straighten the scanned images. Previous Page Next Page Under Mac OS X 1 Select the [Deskew] check box. (This is the same in Simple Mode and Advanced Mode.) Under Windows 1 In the ISIS/TWAIN driver properties dialog box, click the [Basic] tab → select the [Deskew] check box.
Back Contents Moire Reduction This section describes the procedure for setting to reduce the moire effect (a shimmering, wavy pattern) that may appear when scanning color documents or scanning in grayscale. Previous Page Next Page Under Mac OS X 1 Switch to Advanced Mode and click [Image Processing]. 2 For [Moire Reduction], select [High Quality Moire Reduction].
Back Contents Previous Page Next Page Adjusting the Scan Area NOTE When a resolution higher than 300 dpi is selected for [Dots per inch], [High Quality Moire Reduction] is greyed out. • • This section describes the procedure for scanning part of a document image. When a resolution of 240 dpi or less is selected for [Dots per inch], you can click [High Speed Moire Reduction].
Contents Scan Area Dialog Box (ISIS Driver) Scan Area Dialog Box (TWAIN Driver) If there is a [Scan] item in the Settings dialog box of the application, it will look as follows. Back Previous Page Next Page Page Size This setting is linked to the [Page Size] setting, for selecting the size of document pages to scan. Clicking the [Custom] button opens the [Custom Page Size] dialog box, where non-standard page sizes can be registered as custom page sizes. Area Select the area to be scanned.
Back Contents Under Mac OS X 1 Switch to Advanced Mode and select the [Set Scanning Area] check box. The scan driver settings screen expands, giving access to more settings. Previous Page Next Page Brightness/Contrast Adjustment This section describes the procedure for adjusting the brightness and contrast for scanning. Under Windows 1 2 Specify the area of the document to be scanned. To directly specify the area by numeric input, enter the values into the [Width] and [Height] fields.
Back Contents Under Mac OS X - 1 • Switch to Advanced Mode and move the [Brightness] and [Contrast] sliders to adjust the brightness and contrast of the scanned image. Previous Page Next Page [Used the Back Side Contrast] Check Box If the contrast of the front and back of the document pages is different, select this check box to adjust only the contrast of the back side.
Back Contents Gamma Curve Settings This section describes the procedure for adjusting the gamma level for scanning documents. Previous Page Next Page Under Mac OS X 1 Switch to Advanced Mode and click [Gamma Settings]. Under Windows 1 In the ISIS/TWAIN driver properties dialog box, click the [Brightness] tab → click [Gamma]. 2 Select the [Custom] check box in the [Gamma Settings] dialog box → specify the settings as necessary. The [Gamma Settings] dialog box appears.
Back Contents Previous Page Next Page Image Contour Adjustment • • When you make custom gamma correction settings, all settings related to the brightness of the scanned image will be set automatically. This section describes the procedure for adjusting the contours of the scanned image. The settings you can specify are as follows: - Select Select the side and color for the custom setting. y The color bar and color of the sample image are changed to show the specified color.
Contents Back Previous Page Next Page Under Mac OS X 79 NOTE 1 Switch to Advanced Mode and click [Image Processing]. 2 Adjust the [Edge emphasis] slider to correct the outline of the scanned image. Move the slider toward [Soft] to soften the image contours, or toward [Sharp] to sharpen the image contours.
Back Contents Image Rotation This section describes the procedure for rotating the orientation of the scanned image. Previous Page Next Page Under Mac OS X 1 Switch to Advanced Mode and click [Image Processing]. 2 Under [Document Orientation], select the rotation angle for the image. Under Windows 1 80 In the ISIS/TWAIN driver properties dialog box, click the [Image processing] tab → select the angle to rotate the image from the [Document Orientation] drop-down list.
Back Contents Previous Page Next Page Correcting Text Orientation NOTE The scanned image will be rotated as follows, according to the orientation of the placed document and the specified angle. This section describes the procedure for automatically correcting the orientation of the text when scanning.
Back Contents Under Mac OS X 1 Select the [Text Orientation Recognition] check box. (This is the same in Simple Mode and Advanced Mode.) Previous Page Next Page Removing the Document Background/Preventing Bleed Through This section describes the procedure for setting to reduce bleed through when scanning thin document pages and pages with dark content on the back side, or to remove the background from document images.
Back Contents Under Mac OS X 1 Switch to Advanced Mode and click [Image Processing]. Previous Page Next Page Omitting a Specific Color This section describes the procedure for setting to omit borders and ruled lines of a specified color (red, green, or blue) from the scanned image. Under Windows NOTE When the [Mode] setting is [24-bit Color] or [Auto Color Detection], the settings below are not available.
Contents Back Previous Page Next Page Under Mac OS X 84 NOTE 1 Switch to Advanced Mode and click [Image Processing]. 2 Under [Color drop-out], select a color to ignore. You can specify different settings for the front and back side of the document.
Back Contents Enhancing the Red Color This section describes the procedure for setting the scanner to enhance the red color when performing black-and-white scanning. Under Windows NOTE If you select [24-bit Color] or [Auto Color Detection] from the [Mode] drop-down list of the [Basic] tab, you cannot specify this setting. 1 85 In the ISIS/TWAIN driver properties dialog box, click the [Image processing] tab → select [Red Enhance] from the [Front] and [Back] drop-down lists under Color drop-out.
Back Contents 2 Under [Color drop-out], select [Red Enhance]. Previous Page Next Page Rapid Recovery System This section describes the procedure for setting the system recovery method used by the scanner when document feeding stops due to a paper jam or other error during scanning. Under Windows 1 NOTE You can set specify different settings for the front and back side of the document.
Contents Back Previous Page Next Page Under Mac OS X 87 NOTE 1 Switch to Advanced Mode and click [More]. 2 Select the [Rapid recovery system] check box. If you select [Rapid recovery system] and a paper jam or other error causes document feeding to stop while scanning, scanning stops without sending an error notification to the application program. After you clear the paper jam or resolve the error, you can resume the normal scanning operations.
Back Contents Double Feed Detection This section describes the procedure for setting the scanner to stop document feeding when double feeding of document pages is detected. Under Windows 1 88 Click the [Others] tab → select the [Detect by Length] or [Detect by Ultrasonic] (for the DR-2510C only) check box under [Double Feed Detection → click [OK]. Previous Page Next Page Under Mac OS X 1 Select the [Double Feed Detection] check box. (This is the same in Simple Mode and Advanced Mode.
Back Contents 2 When switched to Advanced Mode, the detection method can be selected (DR-2510M only). Previous Page Next Page Feeding Options This section describes the procedure for selecting the method for feeding documents. Under Windows 1 • NOTE Details of each detection method are indicated below. [Detect by Length] This detection method is effective when scanning documents of the same size. It detects double-feeding when a document is 2.0" (50 mm) longer or 2.
Contents Back Previous Page Next Page Under Mac OS X 1 Switch to Advanced Mode and click [More]. • NOTE Details of each feeding method are indicated below. [Standard Feeding] This feeding method is good for scanning small batches of documents that are loaded one batch at a time: scanning stops when the loaded documents have been scanned.
Back Contents Prescan This section describes the procedure for checking a scanned image and adjusting the brightness and contrast accordingly. 3 Previous Page Next Page Check the displayed preview image → adjust [Brightness] and [Contrast] as necessary using the sliders or up/down buttons → click (Start) to save the scanned image. Under Windows 1 In the ISIS/TWAIN driver properties dialog box, click the [Others] tab → select the [Prescan] check box.
Contents Under Mac OS X 1 2 Previous Page Next Page Adjust brightness and contrast if necessary. (This is the same in Simple Mode and Advanced Mode.) Select the [Check the image of the first page] check box and start scanning. (This is the same in Simple Mode and Advanced Mode.) The Scanner driver settings screen expands, and the scanned image of the first page appears in the preview area.
Back Contents Registering Scanning Conditions This section describes the procedure for registering specified scanning conditions. Previous Page Next Page Under Mac OS X 1 Switch to Advanced Mode, make the necessary settings, and then select [Add/Delete] for [Favorite Settings]. Under Windows 1 93 Specify the scanning conditions as necessary on the [Basic] tab, [Brightness] tab, [Image processing] tab, and [Others] tab of the ISIS/TWAIN driver properties dialog box.
Back Contents Checking the Version This section describes the procedure for checking the version of the ISIS/TWAIN driver you are currently using. Previous Page Next Page Under Mac OS X 1 Click (Info button). (This is the same in Simple Mode and Advanced Mode.) 2 Check the displayed information, and click Under Windows 1 2 94 In the ISIS/TWAIN driver properties dialog box, click the [Basic] tab → click [About]. Check the content of the [About] dialog box → click [OK]. to close the dialog box.
Contents Back Previous Page Next Page 1. Regular Maintenance Chapter 7 Maintenance 1. Regular Maintenance .............................................................. 95 Cleaning the Scanner............................................................................ 95 Cleaning the Inside of the Scanner ....................................................... 95 Cleaning the Sensor Glass and the Rollers ........................................... 96 2.
Back Contents Cleaning the Sensor Glass and the Rollers If scanned images contain streaks, or if the scanned documents become dirty, the sensor glass or rollers inside the scanner may be dirty. Clean them periodically. 1 Open the document feed tray (See p. 23). 2 Press the OPEN knob from both sides (c), and pull the front unit out and downward to open it (d). 4 Previous Page Next Page Use a clean dry cloth to wipe dirt off the sensor glass.
Contents 6 Clean the e rollers by wiping the exposed part without turning them. Back Previous Page Next Page 9 Wipe the removed rollers with a cloth that has been dampened with water and thoroughly wrung out. 10 Reattach the retard roller and feeding roller (See p. 102 and p. 104.). e 7 Wipe the document holding guide with a cloth that has been dampened with water and thoroughly wrung out.
Back Contents 2. Removing and Attaching the Rollers and Document Holding Guide Previous Page Next Page Resetting the Counter After replacing the feed rollers, open the counter settings dialog box and reset the counter. To clean or replace the feeding roller, retard roller, or document holding guide, remove and then attach the parts as described in each respective section. Under Windows CAUTION Do not use excessive force when removing or attaching the rollers and document holding guide.
Contents 4 Control Panel (Classic View) If the Control Panel is displayed with the Category View, switch to Classic View. 3 99 Double-click [Scanners and Cameras]. Back Previous Page Next Page Right-click [CANON DR-2510C USB] or [CANON DR-2010C USB] → click [Properties].
Back Contents 5 6 100 Click the [Maintenance] tab → [Reset]. Under Mac OS X 1 Confirm that the counter for the selected roller is set to 0 → click [OK]. Previous Page Next Page Start Image Capture. To start Image Capture, click the hard disk icon (e.g. [Macintosh HD]), the [Applications] folder, and then the [Image Capture] icon. 2 Click [Browse Devices] in the [Devices] menu. 3 Select the scanner you want to use, and select the [Use TWAIN software] check box. 4 Click [OK].
Back Contents 8 Click [Maintenance]. The [Maintenance] dialog box appears. Previous Page Next Page Removing/Attaching the Feeding Roller To remove or attach the feeding roller, follow the procedure below. CAUTION Use caution when removing or attaching the feeding roller. Using excessive force may cause damage or personal injury. Removing the Feeding Roller 9 Click [Reset]. 10 Click to close the dialog box. 1 Open the document feed tray (See p. 23).
Contents 3 Open the roller cover on the main unit by placing your fingers in the grooves and pulling it down. 4 Lift up the roller fixing lever (c), and slide it to the left (d). 5 Remove the feeding roller by moving it to the left to detach it from its shaft, and pull it out of the slot. 102 Back Previous Page Next Page Attaching the Feeding Roller 1 Insert the feeding roller into the slot inside the roller cover, and align the notch on the roller with the shaft on the main unit.
Back Contents 4 Close the roller cover. Make sure that the cover is completely closed by pushing until you hear a click. Previous Page Next Page Removing/Attaching the Retard Roller To remove or attach the retard roller, follow the procedure below. CAUTION Use caution when removing or attaching the retard roller. Using excessive force may cause damage or personal injury. Removing the Retard Roller 5 Close the front unit by gently pushing it up on both sides until it clicks into place.
Contents 3 4 5 104 Grasp the ends of the roller cover inside the front unit and pull it down to open it. Back Previous Page Next Page Attaching the Retard Roller 1 Insert the retard roller into the slot inside the roller cover, and align the notch on the roller with the shaft on the front unit. 2 Slide the roller fixing lever to the left to lock the roller into the hole on the left of the retard roller. 3 Push down the lever to lock the shaft of the feeding roller into place.
Back Contents 4 Close the roller cover. Make sure that the cover is completely closed by pushing until you hear a click. Previous Page Next Page Removing/Attaching the Document Holding Guide To remove or attach the document holding guide, follow the procedure below. CAUTION Use caution when removing or attaching the document holding guide. Using excessive force may cause damage or personal injury.
Contents Back Previous Page Next Page 1. Common Problems and Solutions Chapter 8 Troubleshooting 1. Common Problems and Solutions .............................................. 106 This section provides recommended solutions to common problems. If you have a problem that is not solved by the following, contact your local authorized Canon dealer. Problem 1 Solutions The scanner will not turn on. (1) Confirm that the power switch is set correctly.
Contents Problem 4 Solutions Problem 5 Solutions If white lines or streaks appear in scanned images. Clean both sides of the scanner glass, and the rollers (both rubber and metal). If a sticky substance such as glue or correction fluid is found, carefully wipe with just enough pressure to clean the area where the lines appear. If the problem cannot be solved by cleaning, the internal glass may be scratched. Contact your local authorized Canon dealer. Problem 6 Solutions Pages are missing.
Contents Back Previous Page Next Page 2. Software Troubleshooting 3. Q & A (Useful tips) This section describes troubleshooting problems and solutions for operating the supplied software (CaptureOnTouch and CapturePerfect). Here are some useful tips for scanning documents. If scanning is too slow (1) Close other running programs, if any. (2) Scanning can be slowed down by memory shortage caused by memoryresident applications such as anti-virus programs.
Contents CapturePerfect Scanner setting configurations cannot be copied or backed up in CapturePerfect. Back Previous Page Next Page Is it possible to add or insert images in a scanned image file? CapturePerfect includes a function to add or insert pages in scanned image files. Refer to the CapturePerfect Operation Guide for details. Can I copy or back up CaptureOnTouch settings? Click the [Environ.
Contents How can I attach scanned data to an e-mail (or send it as e-mail)? CaptureOnTouch • For Scan First scanning, select [Attach to E-mail] on the output method selection screen. • For selected job scanning, select "Attach to E-mail" as the [Output method] when registering the job. CapturePerfect Scan using the Scan Batch to Mail function. Alternatively, register a job with the output destination as e-mail. Back Previous Page Next Page 4.
Contents 2 Double-click [Add or Remove Programs]. Back Previous Page Next Page Uninstalling the ISIS/TWAIN Driver and CaptureOnTouch 1 From the Programs list, click [Canon DR-2510C Driver] / [Canon DR2010C Driver] (or [DR-2510C CaptureOnTouch] / [DR-2010C CaptureOnTouch]) → click [Remove]. The [Add or Remove Programs] dialog box appears. The delete confirmation screen appears. 111 2 Click [Yes] in the [DR-2510C Setup] / [DR-2010C Setup] dialog box. 3 Click [Finish].
Contents Uninstalling CapturePerfect 3.0 1 From the Programs list, click [CapturePerfect 3.0] → [Remove]. Back Previous Page Next Page Uninstalling on Mac OS X No uninstaller is provided for Mac OS X drivers. To uninstall, use Finder to delete the following files. Scanner Driver: /Library/Image Capture/TWAIN Data Sources/DR2510M.ds /Applications/Canon DR-2510M CaptureOnTouch: /Library/Receipts/DR-2510M Driver.pkg /Library/Receipts/DR-2510M CaptureOnTouch.pkg The delete confirmation screen appears.
Back Contents Previous Page Next Page Specifications Chapter 9 Appendix Specifications Main Unit Specifications......................................................................... 113 Specifications ...................................................................................... 113 Replacement Parts .............................................................................. 114 External Dimensions............................................................................
Contents Duplex 200 x 200 dpi 50 images/min.(DR-2510C/DR-2510M), 40 images/min.(DR-2010C/DR-2010M) 300 x 300 dpi 50 images/min.(DR-2510C/DR-2510M), 40 images/min.(DR-2010C/DR-2010M) Grayscale Simplex 200 x 200 dpi 25 pages/min.(DR-2510C/DR-2510M), 20 pages/min.(DR-2010C/DR-2010M) 300 x 300 dpi 25 pages/min.(DR-2510C/DR-2510M), 20 pages/min.(DR-2010C/DR-2010M) Duplex 200 x 200 dpi 50 images/min.(DR-2510C/DR-2510M), 40 images/min.(DR-2010C/DR-2010M) 300 x 300 dpi 50 images/min.
Contents 6.3" (160mm) External Dimensions 6.3" (160mm) 19.5" (490mm) 115 (With the document feed tray open) 9.8" (245mm) 11.
Contents Back Previous Page Next Page FCC REGULATIONS (For 120 V model) European Union (and EEA) only. Document Scanner, Model M11065/M11064/M11074/M11073 This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/ EC) and your national law. This product should be handed over to a designated collection point, e.g.
Contents INDEX A AC Adapter ......................................................................................................... 7 B Batch Separation .............................................................................................. 90 Bypass mode .................................................................................................... 26 C CaptureOnTouch .............................................................................................. 35 Job buttons .............
Contents Document eject tray ................................................................................. 23 Document feed tray ................................................................................. 23 Document stopper ................................................................................... 23 R Recognizing the scanner by computer ............................................................. 19 Replacement parts ....................................................................