NA10 User Manual This manual describes the setup and operating procedures for the NA10 Network Adapter for the Canon imageFORMULA DR series. To use this device, read this manual together with the instructions for the scanner to be connected. Procedures and Example Screens This manual describes operations using Windows 7 as examples. Table of Contents About This Device ...............................................................4 Setup....................................................................
Trademarks FCC REGULATIONS (For North America) ● Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. ● imageFORMULA is a trademark of CANON ELECTRONICS INC. ● Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries.
FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
About This Device This device allows you to connect LAN-compatible computers to a scanner via a network. By connecting a scanner to the device with a USB cable, you can perform scanning operations from a computer via the network. D USB connector Names of Parts A B C D When DHCP is disabled, holding this button while turning on the device lights the DHCP lamp and enables DHCP. Depending on the connection environment, it may take up to 2 minutes for the device to start up.
Setup (1) Installing the Scanner Driver (2) Connecting to the Scanner To use the device, the driver of the scanner to be used in conjunction with the device must be updated to its latest version. The scanner driver is available on the downloads page of the Canon website. For details on acquiring and installing the driver, visit the Canon support website. http://www.canon-elec.co.jp/products/ims/softwareDownload/ index.html A Connect the supplied USB cable to the USB ports on the device and the scanner.
Cord Cover and Stand You can attach the supplied cord cover to protect the connected cable’s connector. You can attach the stand to set the device upright. In addition, placing the scanner on the stand will stabilize the device. Place the scanner here. CAUTION • When connecting the device to a scanner equipped with a fan, maintain a space of at least 10 mm between the device and the scanner so as not to obstruct the vents.
Connecting to the Wired Network Under factory default conditions, the device will acquire its IP address automatically from a DCHP server. If the network to which the device will connect includes a DHCP server, the device will be usable simply by connecting to that network. You can check whether the device is connected to the network properly and ready for use by performing the following and starting the Driver Setting Tool. 2 Click the [NetworkMonitor] tab.
Specifying a Static IP Address for the Device Perform the following when specification of a static IP address for the device is necessary, such as when the network does not include a DHCP server. 1 Turn on the device while holding the DHCP On/Off button. The power lamp will light. (The other lamps will also light momentarily and then turn off.) Hold the DHCP On/Off button until the Connection lamp lights.
Scanning with the CaptureOnTouch Job Tool from a Smart Device The CaptureOnTouch Job Tool is an application for smart devices (such as smart phones and tablet devices) for controlling scan operations via this device (NA10). Preparation Before Scanning Install the CaptureOnTouch Job Tool on your smart device, connect the NA10 to a computer, and connect your smart device to the network. 1 Install the CaptureOnTouch Job Tool application on your smart device.
Granting Access Permission Job Scanning from the App When saving scanned data in a specific location, a screen asking for permission to access the smart device is displayed. You can save scanned data if you grant access permission. If you do not grant access permission, you cannot save the scanned data. You can change granting/denial of access permission by the following procedure. You can register a job in the CaptureOnTouch Job Tool and execute scanning according to the job's scan settings.
3 Hint Register the job. You can register multiple jobs. Up to 99 jobs can be registered. A Tap [Add new]. 4 Tap the registered job's icon. Scanning is executed and the scanned data is saved in the shared folder of the specified computer. B On the [Add] screen, set the [Job name] and [Scan setting], then tap [SAVE]. 5 Tap [ ] to save the scanned data in the smart device. Scanned data is saved in the smart device.
Editing job settings You can edit the settings of registered jobs. 3 Change the settings in [Job name] and [Scan setting], and tap [SAVE]. The settings are saved. 1 Press and hold the icon of the job you want to edit. [ ] appears to indicate the job is editable. Hint To cancel editing, tap the job icon again or tap [ ] – [Deselect]. 2 Deleting jobs You can delete registered jobs. Tap [ ]. The [Edit] screen appears. 1 Press and hold the icon of a job you want to delete.
• By tapping [ ] – [Select all] or [Deselect], you can select all jobs or cancel the selected state. 2 3 Tap [ ], or tap [ 4 Enter the administrator password. ] — [Copy job registration settings]. Tap [ ]. A confirmation message appears. 3 Tap [OK]. The selected job(s) is deleted. Enter the same password as for the Web menu. For details, see “Displaying the Web Menu of This Device” (p. 21).
To Delete Jobs Copied to the Scanner Jobs copied to the scanner can be deleted. 1 Delete the job(s) from the CaptureOnTouch Job Tool. Job Scanning from a PC When there is one or more computer on the same network, you can use the CaptureOnTouch Job Tool to select and execute jobs registered by CaptureOnTouch on each computer. For details, see “Deleting jobs” (p. 12). Hint To delete all jobs copied to the scanner, delete all jobs from the CaptureOnTouch Job Tool. 2 Select the scanner.
3 Select the scanner. A Tap [ ]. 5 Tap the job number to execute, and tap [Scan]. Scanning executes according to the scan settings of the selected job number. B Select the scanner on the [Select Scanner] screen. 4 Select a computer. A Tap [ ]. Hint • Using the CaptureOnTouch favorite on the computer selected in the above figure, the job is registered as shown below. B On the [Select computer] screen, select a computer.
Scanning from a Computer with the CaptureOnTouch Job Tool CaptureOnTouch Job Tool for Windows is an application to control scanning via the NA10 by computer operation. Preparation Before Scanning Install the CaptureOnTouch Job Tool on the computer, and connect it and the NA10 to the network. 1 2 Install the CaptureOnTouch Job Tool application on the computer. Connect the NA10 to a wired network. For details, see “Connecting to the Wired Network” (p. 7).
3 Register the job. A Click [Add]. 4 Click the registered job's icon, then click [Scan]. Scanning is executed and the scanned data is saved in the shared folder of the specified computer. B On the Add screen, set the [Job name] and [Scan setting], then click [Save]. Editing job settings You can edit the settings of registered jobs. 1 Click the icon of the job you want to edit.
3 Change the settings in [Job name] and [Scan setting], and click [Save]. Deleting all jobs You can delete all registered jobs at once. The settings are saved. 1 Click [Delete All]. A confirmation message appears. Deleting jobs You can delete registered jobs. 1 Click the icon of the job you want to delete. 2 Click [ ]. The selected job(s) is deleted. 18 2 Click [OK]. All jobs are deleted.
CAUTION Scanning with Scanner Start Button You can copy a job registered in the CaptureOnTouch Job Tool to the scanner, then scan according to those scan job settings by pressing the scanner's start button. In this scanning method, since the NA10 controls the scanner, the computer is not needed to execute scanning. 1 The number of jobs that can be copied depends on the scanner. 6 Scanning executes according to the scan settings of the selected job number.
B Select the scanner on the [Select Scanner] screen. 3 Click [ ], or click [ 4 Enter the administrator password. ] — [Copy job registration settings]. Enter the same password as for the Web menu. For details, see “Displaying the Web Menu of This Device” (p. 21). 5 Click [OK]. Jobs deleted from the CaptureOnTouch Job Tool are deleted from the scanner.
Using the Web Menu Displaying the Web Menu of This Device Since this device has the HTTP protocol, advanced settings can be configured or changed via a web browser. IMPORTANT • We recommend the following web browsers: Windows Displaying the Web Menu of This Device Hint This section describes operations for when the DR-M160II is being used. When using a different model, replace any instance of the model name with that of the model you are using.
3 Select the scanner from the list, and click [Property]. The device’s web page opens, and the login screen is displayed. Specifying the Device’s IP Address to Display the Web Menu Enter the device’s IP address in the address bar of the web browser, and press the Enter key. Example: Enter 192.168.0.10 (displayed as “http://192.168.0.10/”) The device’s web page opens, and the login screen is displayed.
Web Menu Settings This section describes the setting items on each of the pages of the web menu. Network Setting If you click [Network Setting] on the left menu, the page below is displayed. Scanner Name Setting If you click [Scanner Name Setting] on the left menu, the page below is displayed. Item Description Scanner Name Displays the device name of the connected scanner. Item Description Default Value DHCP Enable ([ON]) / disable ([OFF]) the DHCP protocol.
Item Description Default Gateway Set the gateway IP address of the device. If DHCP is enabled, the default gateway obtained from it will be applied. The value must be four decimal numbers separated by dots and expressed in the [xxx.xxx.xxx.xxx] format. Also, the gateway needs to be running in the same subnetwork as the device. 24 Default Value mDNS Setting If you click [mDNS Setting] on the left menu, the page below is displayed. 192.168.0.
Password Setting Maintenance Setting If you click [Password Setting] on the left menu, the page below is displayed. If you click [Maintenance Setting] on the left menu, the page below is displayed. In this page, you can restore the device’s factory default settings and update the firmware. Item Description Default Value Current Password Enter the current password. None Item Description Set the administrator password (up to 32 characters).
Software License The device includes software that is licensed under GNU GENERAL PUBLIC LICENSE (GPL), GNU LESSER GENERAL PUBLIC LICENSE (LGPL), or proprietary licenses. You can view the original text of a software license via the device’s web menu. 1 2 3 26 Follow the steps in “Displaying the Web Menu of This Device” (p. 21), and display the [Device information] screen. Click [▼] to display the next page of the [Device information] screen. Click [Download] for [Third party license].
Troubleshooting Problem 5 The scanner automatically turns itself off, making the connection unavailable. • Confirm that the scanner and the device are turned on. • Confirm that the scanner is compatible with the device. • Confirm that the device and scanner are connected via USB cable. • Confirm that the network cable is connected properly. • Confirm that the IP address is configured properly.
Specifications Main Unit Type Network Adapter Scanner connection interface USB 2.0 Hi-Speed (Type A) Network interface IEEE802.3 10Base-T/100Base-TX/ 1000Base-T Dimensions 116 mm x 93.6 mm x 28.8 mm (4.57" x 3.69" x 1.13") (W x D x H; without cord cover) Mass Approx. 179 g (0.4 lb) (main body only) Power supply AC adapter (use the adapter supplied with the scanner) Power consumption Max. during operation: 5.6 W; During standby: 4.2 W; During power off: 0.
Safety-related markings on the machine Marquages de sécurité sur la machine Marcature di sicurezza sulla macchina Sicherheitshinweise auf der Maschine Marcas de la máquina relacionadas con la seguridad Veiligheidsmarkeringen op de machine Makine üzerindeki güvenlik iġaretleri [English] [Français] [Italiano] [Deutsch] [Español] [Nederlands] [Türkçe] Switch (On) Commutateur (Marche) Interruttore (On) Schalter (Ein) Interruptor (encendido) Schakelaar (On) Anahtar (Açık) Power on Sous tension Alimentazione pr
[English] [Français] Switch (Push-On/Push-Off) Commutateur (Appuyer pour mettre en marche/Appuyer pour arrêter) Power on/off (no standby current) Sous/hors tension (pas de courant de veille) [Italiano] Interruttore a pulsante bistabile (On/Off) Alimentazione on/off (nessuna corrente di standby) [Deutsch] Schalter (Ein- und Ausschalten durch Drücken) Ein- und Ausschalten (ohne Ruhestromaufnahme) [Español] Interruptor (pulsado para encendido/apagado) Encendido/apagado (sin corriente en espera) [Ne
[English] [Français] [Italiano] [Deutsch] [Español] [Nederlands] [Türkçe] DC symbol Symbole CC Simbolo corrente continua (C.C.) Gleichstrom-Symbol Símbolo CC DC-pictogram DC sembolü Indicates direct current Indique qu’il s’agit de courant continu Indica la corrente continua Kennzeichnet Gleichstrom Indica corriente continua Geeft gelijkstroom aan Düz akımı gösterir [English] [Français] [Italiano] [Deutsch] [Español] [Nederlands] [Türkçe] DC polarity Polarité CC Polarità C.C.
CANON ELECTRONICS INC. 3-5-10 SHIBAKOEN, MINATO-KU, TOKYO 105-0011, JAPAN CANON U.S.A. INC. ONE CANON PARK, MELVILLE, NY 11747, U.S.A. CANON CANADA INC. 8000 MISSISSAUGA ROAD, BRAMPTON, ONTARIO L6Y 5Z7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59, 1185 XB AMSTELVEEN, THE NETHERLANDS CANON AUSTRALIA PTY. LTD. BUILDING A, THE PARK ESTATE, 5 TALAVERA ROAD, MACQUARIE PARK, NSW 2113, AUSTRALIA CANON SINGAPORE PTE. LTD. 1 FUSIONOPOLIS PLACE, #15-10, GALAXIS, SINGAPORE 138522 CANON INDIA PVT.
