- Safety Instructions Read this guide first. Please read this guide before operating this product.
Contents Contents Chapter 1 Preface.................................................................................................................3 Read the Safety Instructions thoroughly..................................................4 Chapter 2 How to use this manual.....................................................................................5 Symbols used in this manual....................................................................6 Chapter 3 Legal Notices...............................
Chapter 1 Preface
Read the Safety Instructions thoroughly Read the Safety Instructions thoroughly Thank you for purchasing the Canon imageRUNNER ADVANCE C9075S PRO/C9065S PRO. Please read the safety instructions in this manual thoroughly before operating the machine. After reading this manual, store it in a safe place for future reference.
Chapter 2 How to use this manual
Symbols used in this manual Symbols used in this manual The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety. Overview of the attention-getters# Word Icon Indicates WARNING Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. To use the machine safely, always pay attention to these warnings.
Chapter 3 Legal Notices
Legal Notices Legal Notices Product name Safety regulations require the product's name to be registered. In some regions where this product is sold, the following name(s) in parenthesis may be registered instead.
Legal Notices Laser Safety This product complies with 21 CFR Chapter 1 Subchapter J as a Class I laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. Also, this product is certified as a Class 1 laser product under IEC60825-1:2007. This means that the product does not produce hazardous laser radiation.
Legal Notices No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage or retrieval system without the prior written permission of Canon Inc. Disclaimers The information in this document is subject to change without notice. CANON INC.
Legal Notices # • • • • • • • • Paper money Money orders Certificates of Deposit Postage stamps (cancelled or uncancelled) Identifying badges or Insignias Selective service or draft papers Checks or drafts issued by governmental agencies Motor vehicle licenses and certificates of title • • • • • Travellers checks Food stamps Passports Immigration papers Internal revenue stamps (cancelled or uncancelled) • Bonds or other certificates of indebtedness • Stock certificates • Copyrighted works/Works of art
Legal Notices 12 Chapter 3 - Legal Notices
Chapter 4 Important safety instructions
Introduction Introduction Please read these "Important Safety Instructions" thoroughly before operating the machine. As these instructions are intended to prevent injury to the user or other persons or destruction of property, always pay attention to these instructions. Also, since it may result in unexpected accidents or injuries, do not perform any operation unless otherwise specified in the manual.
Installation Installation # WARNING • Do not install the machine near alcohol, paint thinner, or other flammable substances. If flammable substances come into contact with electrical parts inside the machine, it may result in a fire or electrical shock. Do not place the following items on the machine. If these items come into contact with a high-voltage area inside the machine, it may result in a fire or electrical shock.
Installation CAUTION • Do not remove the machine's level- ing feet after the machine has been installed, as this may cause the machine to fall or tip over, resulting in personal injury.
Power supply Power supply # WARNING • Do not damage or modify the power cord. Also, do not place heavy objects • • • • • • • on the power cord, or pull on or excessively bend it, as this could cause electrical damage and result in a fire or electrical shock. Keep the power cord away from a heat source; failure to do this may cause the power cord coating to melt, resulting in a fire or electrical shock. Do not connect or disconnect the power cord with wet hands, as this may result in electrical shock.
Handling Handling # WARNING • Do not attempt to disassemble or modify the machine. There are high-tem- • • • • • • perature and high-voltage components inside the machine which may result in a fire or electrical shock. If the machine makes strange noises, or gives off smoke, heat, or strange smells, immediately turn OFF the main power switch, and disconnect the power cord from the power outlet. Then, contact your local authorized dealer.
Handling CAUTION • Do not press down hard on the feeder when using the platen glass to make copies of thick books. Doing so may damage the platen glass and result in personal injury. • Do not touch the finisher while the machine is printing, as this may result in personal injury. • Paper that has just been output from the machine may be hot. Be careful when removing or aligning paper from the output tray. Touching paper right after it is output may result in low-temperature burns.
Handling # CAUTION • The laser beam can be harmful to human bodies. Since radiation emitted inside the product is completely confined within protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation. Read the following remarks and instructions for safety. • Never open covers other than those instructed in the manuals for this machine. • Do not remove the following caution label which is attached to the machine.
Maintenance and inspections Maintenance and inspections # WARNING • When cleaning the machine, first turn OFF the main power switch, then • • • • disconnect the power cord. Failure to follow these steps may result in a fire or electrical shock. Disconnect the power cord from the power outlet regularly, and clean the area around the base of the power plug's metal pins and the power outlet with a dry cloth to ensure that all dust and grime is removed.
Maintenance and inspections # WARNING • Make sure that the power plug is firmly inserted into the power outlet after cleaning the machine. Do not use the machine while the connection is loose, as doing so may cause a fire. • Check the power cord and power plug regularly. If the following conditions occur, contact your local authorized dealer, as the condition may cause a fire: - There are burn marks on the power plug. - The blade on the power plug is deformed or broken.
Maintenance and inspections # CAUTION • The fixing unit and its surroundings inside the machine may become hot during use. When removing jammed paper or when inspecting the inside of the machine, do not touch the fixing unit and its surroundings, as doing so may result in burns or electrical shock. • When removing jammed paper or when inspecting the inside of the machine, do not expose yourself to the heat emitted from the fixing unit and its surroundings for a prolonged period of time.
Maintenance and inspections # CAUTION • When removing jammed paper or replacing the toner cartridge, take care not • • • • • • 24 to allow the toner to come into contact with your hands or clothing, as this will dirty your hands or clothing. If they become dirty, wash them immediately with cold water. Washing them with warm water will set the toner, and make it impossible to remove the toner stains.
Consumables Consumables # WARNING • Do not burn or throw used toner cartridges into open flames, as this may cause toner remaining inside the cartridges to ignite, resulting in burns or a fire. • Do not store toner cartridges or copy paper in places exposed to open flames, as this may cause the toner or paper to ignite, resulting in burns or a fire.
Other warnings Other warnings # WARNING For cardiac pacemaker users: This product emits low level magnetic flux. If you use a cardiac pacemaker and feel abnormalities, please move away from the product and consult your doctor.
Chapter 5 Installation location and handling
Introduction Introduction This section describes precautions for installation location and handling. We recommend that you read this section prior to using this machine.
Avoid installing the machine in the following locations Avoid installing the machine in the following locations • Avoid locations subject to temperature and humidity extremes, whether low or high. For example, avoid installing the machine near water faucets, hot water heaters, humidifiers, air conditioners, heaters, or stoves. • Avoid installing the machine in direct sunlight. If this is unavoidable, use curtains to shade the machine.
Avoid installing the machine in the following locations • Avoid locations where a considerable amount of dust accumulates. • Avoid locations where ammonia gas is emitted. • Avoid locations near volatile or flammable materials, such as alcohol or paint thinner. • Avoid locations that are subject to vibration. For example, avoid installing the machine on unstable floors or stands. • Avoid exposing the machine to rapid changes in temperature.
Avoid installing the machine in the following locations • Avoid installing the machine near computers or other precision electronic equipment. Electrical interference and vibrations generated by the machine during printing can adversely affect the operation of such equipment. • Avoid installing the machine near televisions, radios, or similar electronic equipment. The machine might interfere with sound and picture signal reception.
Select a safe power supply Select a safe power supply • Connect the plugs of the imageRUNNER ADVANCE C9075S PRO/C9065S PRO to an outlet that is 208V 15A or greater. • Make sure that the power supply for the machine is safe, and has a steady voltage. • Do not connect other electrical equipment to the same power outlet to which the machine is connected. • Do not connect the power cord to a multiplug power strip, as this may cause a fire or electrical shock.
Moving the machine Moving the machine • If you intend to move the machine, even to a location on the same floor of your building, contact your local authorized dealer beforehand. Do not attempt to move the machine yourself.
Handling precautions Handling precautions • Do not attempt to disassemble or modify the machine. • Some parts inside the machine are subject to high voltages and temperatures. Take adequate precautions when inspecting the inside of the machine. Do not carry out any inspections that are not described in the manuals for this machine. • Be careful not to spill liquid or drop any foreign objects, such as paper clips or staples inside the machine.
Handling precautions ( side) (The shape of the power plug may differ depending on your location.) • Do not turn the main power switch OFF or open the front covers while the ma- chine is in operation. This may result in paper jams. • Do not use flammable sprays, such as spray glue, near the machine. There is a danger of ignition. • This machine generates a slight amount of ozone and other substances during normal use. Although sensitivity to these substances may vary, this amount is not harmful.
Handling precautions • Paper that has just been output from the machine may be hot. Be careful when removing or aligning paper from the output tray. Touching paper right after it is output may result in low-temperature burns.
Provide adequate installation space Provide adequate installation space Provide enough space on each side of the machine for unrestricted operation. • The Booklet Finisher-A1, Paper Folding Unit-G1, Professional Puncher Integra- tion Unit-B1, Professional Puncher-C1, Document Insertion Unit-H1, Buffer Pass Unit-F1, Duplex Color Image Reader Unit-A1, and Multi-drawer Paper Deck-A1 are attached.
Provide adequate installation space 38 Chapter 5 - Installation location and handling
Chapter 6 Inspection of the breaker
Introduction Introduction This machine has a breaker that detects excess current or leakage current. Make sure to test the breaker once or twice a month using the following procedure. # IMPORTANT • Make sure that the main power is turned OFF, before inspecting the breaker. • If a malfunction occurs after an inspection, contact your local authorized dealer.
Checking the breaker Checking the breaker 1. Push the test button on the rear of the machine with the tip of a ballpoint pen, or a similar object. # IMPORTANT • Briefly push the test button. # NOTE • The breaker is located on the rear of the machine. 2. Confirm that the breaker lever is switched to the OFF ("O" side) position. ON ( I side) ( OFF side) # IMPORTANT • Do not use the test button to turn the power ON and OFF.
Checking the breaker 3. Switch the breaker lever to ON ("I" side). ON ( I side) ( OFF side) 4. Press the main power switch to the ON ("I" side) position. ( I side) 5. Fill in the check sheet, located on the next page, to document your periodic inspections of the breaker.
Check sheet for the periodic inspection of the breaker Check sheet for the periodic inspection of the breaker Copy this page for future use, and store it in a safe place near the machine to document your periodic inspections of the breaker. • How to Inspect the Breaker Periodically Follow the procedure described in “Periodic inspection of the breaker,” on ‘Checking the breaker’ on page 41, once or twice a month.
Index Index Breaker Check Sheet Breaker .......................................43 Periodic Inspection .........................................43 Breaker Inspection Breaker Inspection ..........................................41 C consumables Warning and Caution .....................................25 H Handling Warning and Caution .....................................18 I Inspections Warning and Caution .....................................21 Installation Warning and Caution ...........................
+3
+3
+3
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada CANON EUROPA N.V. Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands (See http://www.canon-europe.com/ for details on your regional dealer) CANON LATIN AMERICA, INC. 703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A. CANON AUSTRALIA PTY. LTD 1 Thomas Holt Drive, North Ryde, Sydney, N.S.W.
