<< Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MG5220 Windows OS 1
<< Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MG5220 Windows OS Preparing to Connect My Multifunction To My Network 3 Connecting Your MG5220 To Your Network 5 Installing The MG5220 Software 12 2
Preparing to Connect My Multifunction To My Network << Previous Next >> Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network.
Preparing to Connect My Multifunction To My Network << Previous Next >> An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Be sure to prepare an access point. Notes on Network Connection • The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment.
Connecting Your MG5220 To Your Network << Previous Next >> Step 1 Step 2 Use the ↑ or ↓ button (A) to display Setup, then press the right FUNCTION button (B). Use the ← or → button (C) to select Wireless LAN setup, then press the OK button.
Connecting Your MG5220 To Your Network << Previous Next >> Step 3 Step 4 Select Yes, then press the OK button. Select Easy setup, then press the OK button. When wireless connection is enabled, the Wi-Fi lamp lights blue.
Connecting Your MG5220 To Your Network << Previous Next >> Step 5 Step 6 Select the access point name you wrote down, then press the OK button. Make sure that one of the below screens is displayed, then press the right FUNCTION button. If neither is displayed, go to Step 9. Note: • Nearby access points may be detected. • Access point names with 2-byte characters are not displayed properly, however, they can be selected.
Connecting Your MG5220 To Your Network << Previous Next >> Step 7 Enter the network key you wrote down on, then press the left FUNCTION button (E). 1. Press the center FUNCTION button (F) to switch character entry modes. 2. Enter upper and lower case letters of the alphabet correctly.
Connecting Your MG5220 To Your Network << Previous Next >> Step 7 (continued) Character Entry This machine allows you to enter characters when an on-screen keyboard is displayed. Follow the procedure below. 1. When the on-screen keyboard shown above is displayed, press the center FUNCTION button (A) to switch to a keyboard having the characters you want to use. Four character sets are available: Upper-case alphabets, lower-case alphabets, numbers, and symbols.
Connecting Your MG5220 To Your Network << Previous Next >> Step 7 (continued) Character Entry 2. Select a character on the onscreen keyboard using the ↑↓←→ buttons (B) then press the OK button to enter it. Entered characters are displayed on the upper section (C) of the on-screen keyboard. • To insert a space, select Space on the on-screen keyboard and press the OK button.
Connecting Your MG5220 To Your Network << Previous Step 8 Step 9 Make sure that the network key is correct, then press the OK button. When the screen below appears, press the OK button. Next >> Your MG5220 is now connected to your network Note: • If Failed to connect to the access point. appears, press the OK button, make sure that the network key is correct, then enter it again. If a connection still cannot be established, refer to the printed manual: Network Setup Troubleshooting.
Installing The MG5220 Software << Previous Next >> Now that your MG5220 is connected to your network, we need to install the driver and the included software. Before we begin: • Log on as the administrator (or a member of the Administrators group). • Quit all running applications before installation. • If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network.
Installing The MG5220 Software << Previous Step 1 Step 2 Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive. If you are using Windows, the setup program starts automatically. Windows 7/Windows Vista. For Windows XP, skip to Step 3. Next >> Click Run Msetup4.exe on the AutoPlay screen, then click Yes or Continue on the User Account Control dialog box. If the User Account Control dialog box reappears in following steps, click Yes or Continue.
Installing The MG5220 Software << Previous Step 3 Step 4 Click Easy Install Click Install Next >> The drivers, application software, and on-screen manuals are installed. Note: If you want to select particular items to install, click Custom Install.
Installing The MG5220 Software << Previous Step 5 Step 6 Select Use the printer on network, then click Next. Select Next or Skip. Next >> Selecting Next will download and install the EasyWebPrint EX software. Easy-WebPrint EX is Web print software. Internet Explorer 7 or later is required to use this software. An Internet connection is required for installation.
Installing The MG5220 Software << Previous Step 7 Step 8 When the Printer Detection screen appears, click Next. When the Detected Printers List screen appears, select Canon MG5200 series, then click Next. Next >> IMPORTANT IF THE PRINTER CONNECTION SCREEN APPEARS INSTEAD OF THE SCREEN ABOVE, THE CONNECTION METHOD IS NOT CORRECTLY SELECTED IN 5. CLICK CANCEL AND START AGAIN FROM STEP 1, THEN BE SURE TO SELECT USE THE PRINTER ON NETWORK IN 5.
Installing The MG5220 Software << Previous Next >> Step 9 Step 10 Click Complete on the Setup Completion screen. Follow any on-screen instructions to proceed with the remaining software installation.
