Product Instructions IP Ready™ Series FDW75C12N & FDP75C12N Before attempting to connect or operate this product, please read these instructions completely.
IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating & user instructions should be followed. 5. Electrical Connections - Only a qualified electrician should make electrical connections. 6.
FDW75C12N, FDP75C12N IP Ready Network Housing ASSEMBLING THE UNIT: Remove content from all boxes. Contents should include: IP Ready Network Housing with 12Vdc input, wall mount or pendant mounting, heater & blowers, ready for standard IP PTZ cameras. ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY): ! Power 12Vdc, Class 2 Only Total Power: 21 watts Housing only Accessories (Heater/Blower): 21 watts Heater: 20 watts Blower: 1 watt NOTE: This unit is designed for operation in an upright position.
INSTALLATION OF PTZ CAMERA See model for specific instruction. Listed on the following pages are the specific instructions for each of the individual network cameras. See specific instruction for the model that matches the unit you have.
INSTALLING QUICK RELEASE BRACKETS AXIS 213 2539 Mounting Plate: Attach camera using these (2) holes ½" 1" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Captive Screw 2" 1.
INSTALLING QUICK RELEASE BRACKETS AXIS 214 2685 Mounting Plate: Attach camera using these (3) holes 2" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. 1. Install the AXIS 214 camera to the 2685 mounting plate using the (3) 3mm x 12mm bolt and lock washers provided.
INSTALLING QUICK RELEASE BRACKETS CANON VB-C10R 2539 Mounting Plate: Attach camera using these (2) holes ½" 1" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Captive Screw 2" 1.
INSTALLING QUICK RELEASE BRACKETS CANON VB-C50iR 2539 Mounting Plate: Attach camera using these (2) holes ½" 1" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Captive Screw 2" 1.
INSTALLING QUICK RELEASE BRACKETS CANON VC-C4R / VC-C50iR 2539 Mounting Plate: Attach camera using these (2) holes 1" 1" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. Captive Screw 2" 1.
INSTALLING QUICK RELEASE BRACKETS ELMO PTC-200C Mounting plate for this unit is included in the housing packet. Remove existing mounting plate installed in the unit before proceeding. 2539 Mounting Plate: Attach camera using these (4) holes ½" 1" 2. The Elmo PTC-200C camera requires 3.5" of spacing for optimal position within the housing. Use (4) 2" spacer(s), plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the (2) hardware packets. 2" 1.
INSTALLING QUICK RELEASE BRACKETS ELMO PTC-201 Mounting plate for this unit is included in the housing packet. Remove existing mounting plate installed in the unit before proceeding. 2539 Mounting Plate: Attach camera using these (4) holes ½" 2" 2. The Elmo PTC-201 camera requires 2½" of spacing for optimal position within the housing. Use (4) 2" spacer(s) plus (4) ½" spacer(s) provided in the (2) hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above.
INSTALLING QUICK RELEASE BRACKETS ELMO PTC-400C Mounting plate for this unit is included in the housing packet. Remove existing mounting plate installed in the unit before proceeding. 2539 Mounting Plate: Attach camera using these (4) holes ½" 1" 2. The Elmo PTC-400C camera requires 3.5" of spacing for optimal position within the housing. Use (4) 2" spacer(s), plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the (2) hardware packets. 3.
INSTALLING QUICK RELEASE BRACKETS ELMO PTC-401 Mounting plate for this unit is included in the housing packet. Remove existing mounting plate installed in the unit before proceeding. 2539 Mounting Plate: Attach camera using these (4) holes 1" 2" 1. Remove the mounting plate from the camera and place it onto the quick release bracket using the (4) metric 3M Phillips head screws provided with the kit. Then place the ELMO mounting plate back onto the Elmo PTC-401C. - 13 - 2.
INSTALLING QUICK RELEASE BRACKETS JVC VN-C30U 2539 Mounting Plate: Attach camera using these (3) holes ½" 2" 1. Remove the mounting plate from the camera and place it onto the quick release bracket using the (3) metric 3M Phillips head screws provided with the kit. Then place the mounting plate back onto the JVC VN-C30U. - 14 - 2. In the packet, there will be a number of 2 inch and ½ inch spacers.
INSTALLING QUICK RELEASE BRACKETS PANASONIC BB-HCM381 / KX-HMC280 2539 Mounting Plate: Attach camera using this hole ½" 1" 2" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. 1.
INSTALLING QUICK RELEASE BRACKETS PIXORD 261 / 262 2630 Mounting Plate: Attach camera using these (3) holes ½" 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers. Secure 3 screws and captive fastener. 1. Install the camera to the 2630 mounting plate using the (3) 8 x 32 x .
INSTALLING QUICK RELEASE BRACKETS SONY SNCRZ30 2539 Mounting Plate: Attach camera using this hole 2" 2. The SNCRZ30 require 2” of spacing to properly position the camera within the housing. Use (4) 2” spacers provided in the hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4. Slide the mounting plate with camera into position on top of spacers.
INSTALLING QUICK RELEASE BRACKETS SONY SNCRZ50 2539 Mounting Plate: Attach camera using this hole ½" 2" 2. The SONY SNCRZ50 require 2 ½ ” of spacing to properly position the camera within the housing. Use (4) 2” spacers plus (4) ½ “ spacers provided in the hardware packet. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4.
INSTALLING QUICK RELEASE BRACKETS TOSHIBA IK-WB21A 2539 Mounting Plate: Attach camera using these (4) holes 1" 2" 2. The Toshiba 1K-WB21A requires 3” of spacing to properly position the camera within the housing. Use (4) 2” spacers plus (4) 1” spacers provided in the hardware packets. 3. Place (3) 8 x 32 x s Phillips head screws on the top of the spacer as shown above. Be sure to place the screws so that they line up with the open slots on the mounting plate. 4.
INSTALLING THE HOUSING ASSEMBLY: WIRING INSTRUCTIONS RJ45 ! Be sure the bracket is properly and securely mounted to a supporting structure capable of rigidly holding the weight of the entire unit. BNC NOTE: This unit is designed for operation in an upright position. Installing the housing upside down may cause damage to the internal equipment, and will void the warranty. (Large) Power (Small) Alarms INSTALLING PENDANT MOUNT Wiring Color Code Power and Control Inputs AFTER CAMERA INSTALLATION 1.
3. Mount the housing assembly to the mounting bracket and housing coupling. A safety cable is included with the housing to temporarily hold it while making wiring connections. Loop the safety cable over one of the set screws on the housing coupling and make the appropriate connections using the (2) screw-down connectors supplied. 2. The wall mount bracket provided with the FDW7 includes a location for conduit entry. If you wish to install conduit to the bracket remove the conduit hole plug.
Exploded View for Replacement Parts 12 Not included on 12Vdc housings 13 16 14 6 17 (1) 11 10 (1) (4) 9 (2) 8 (1) 7 (2) 6 (3) 4 18 (1) 1 (2) 3 (1) 5 (2) (2) (4) (8) (1) 19 2 (3) (1) 1 (4) (4) (4) (3) - 22 - (1) (4) (1) (4) (1) (4) (3) (1)
Replacement Parts List Part Number Description 1 RPFD7501 LOWER TRIM RING 2 FD7T TINTED REPLACEMENT CAPSULE FD7C CLEAR REPLACEMENT CAPSULE 3 RPFD703 DOME CLAMPING BRACKET 4 RPFD072 24 VAC HEATER 5 RPFD080 (12 VDC) BLOWER (USED IN 24V HOUSINGS) 6 RPFD060 CAMERA BRACKET 7 RPFD050 (MODEL FD7HB) CONNECTION PCB (24VAC ONLY) RPRH707 (MODEL FD7NHB) CONNECTION PCB (NETWORK MODELS) (24VAC ONLY) 8 RPFD040 HOUSING HARDWARE 9 RPFD709 HOUSING TOP 10 RPFD2612 HOUSING TOP - GASKET 11
Mounting Template R .733 2.132 5.500 1.537 2.981 2.000 3.