Canon iR2000/iR1600 Copying Guide
About the Manuals for the Machine The manuals for this machine are divided as follows. Please read them to suit your needs. For Basic Use...................................................... Troubleshooting ................................................. Reference Guide For Basic Copying.............................................. For Convenient Copying.................................... Copying Guide For Remote UI Use .............................................
How This Manual Is Organized Chapter 1 Basic Copying Chapter 2 Useful Copy Functions Chapter 3 Setting/Storing Specifications of the Copy Function Chapter 4 Appendix • Some of the data contained herein may not exactly reflect the current model of the particular product with which this manual has been included. If you have a need for an exact specification, please contact Canon for the current specification.
Table of Contents How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Symbols Used in This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Buttons Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Illustrations Used in This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2 Useful Copy Functions Copying Facing Pages in a Book on Two Separate Sheets of Paper (Two-page Separation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Making Copies with Margins (Margin). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Erasing Shadows and Frame Lines from Copies (Frame Erase) . . . . . . . . . . . . . . . . . . . . . .
How to Use This Manual Symbols Used in This Manual Symbols are used in this manual for explanations of Restrictions and Cautions upon handling and instructions to be observed for safety. WARNING Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. In order to use the machine safely, always pay attention to these warnings.
Basic Copying 1 CHAPTER This chapter describes the basic copy functions. What the iR2000/1600 Series Machine Can Do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Flow of Copy Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Entering the Copy Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What the iR2000/1600 Series Machine Can Do ■ Flexible document handling To make a copy of an original, you have the choice of setting the document in the optional Feeder (ADF-J1) when attached, or placing it directly onto the platen glass. The Feeder is useful when copying a multi-page document, and the platen glass is ideal when copying a single-page document, or from a book. Basic Copying 1 ■ Copy reduction/enlargement You can manually select a reduction / enlargement ratio from 50% to 200%.
Flow of Copy Operations This section describes the flow of basic copy operations. 1 NOTE 1 Basic Copying • For the following items, see the Reference Guide: - Main power and Energy Saver button ( ) - Routine maintenance • If the platen glass is dirty, the output quality may deteriorate. Always keep the platen glass clean. • Do not touch the platen cover while copying. Rocking the cover can distort the image being copied. Place your original. You can set the original both vertically and horizontally.
[Feeder] Staple copy: place the original with its top upward Copies are stapled here. ABC Basic Copying 1 Copies are stapled here. ABC Original (face up) Vertical placement Original (face up) Horizontal placement IMPORTANT • The copies are stapled at the part equivalent to the upper left side of the original. NOTE • A4, B5 and A5-size originals can be placed either vertically or horizontally.
● If the message is displayed ▼ Insert a control card. (See the Reference Guide.) INSERT CONTROL CARD Basic Copying 1 2 Set the desired copy mode (paper size, image quality, exposure, copy ratio and finishing). NOTE • For details about these settings, see the pages from 1-8 in this chapter, or ‘Chapter 2 Useful Copy Functions’. 3 Enter the copy quantity (1 to 99) using the numeric buttons.
NOTE • If there is a current job, the machine scans the original, and waits to print it. Printing starts when the current job is completed. • When scanning is completed, remove the original. • If you have set the Department ID Management, press ID . (See the Reference Guide.) • If the optional Card Reader is attached, remove the control card. (See the Reference Guide.) Basic Copying 1 ● When you want to reserve a copy job while the machine is printing: ▼ Place the original and press (start).
Entering the Copy Quantity The machine allows up to 99 copies to be made. 1 1 Basic Copying Specifying the Required Number of Copies Press numeric buttons to enter the desired copy quantity (1 to 99). The copy quantity appears on the right side of the display. 100% AUTO PAPER TEXT 10 IMPORTANT • You cannot change the copy quantity while copying. Changing the Copy Quantity 1 Press C (Clear) to clear the entered number.
Selecting the Copy Paper Size (Paper Select) You can set the machine to automatically select the paper size, or you can specify the paper size for a copy job. 1 Basic Copying NOTE • When copying an original onto the same size paper at a 100% copy ratio, the periphery of the original may be cut slightly on the copy. For details of the size of the non-image areas, see the Reference Guide. • For instructions about loading paper in the stack bypass, see the Reference Guide.
1 Place your original. Make sure that is displayed. If not, press 100% AUTO PAPER TEXT (Reset). 01 2 Press (Start). Copying starts. NOTE • If the message appears, the paper set is different in size from the original. Set the appropriate paper. If you press (Start) without loading the paper, the machine automatically selects the paper with the least margin, and starts copying.
3 Press (Start). Copying starts. NOTE • To cancel all settings and return the machine to the standby mode, press Basic Copying 1 1-10 Selecting the Copy Paper Size (Paper Select) (Reset).
Adjusting Exposure and Image Quality The exposure and image quality can be adjusted when the original is scanned. 1 Basic Copying Adjusting Copy Exposure You can manually adjust the exposure to the most appropriate level for the original. 1 Place your original. 100% AUTO PAPER TEXT 2 Press (Light) or 01 (Dark) to adjust the exposure. Move the indicator between (Light) and (Dark) below the display. Move the left to make the exposure lighter or to the right to make the exposure darker.
Selecting Image Quality You can adjust image quality to the level best suited to the quality of text or photo originals. The following three modes are available for adjusting image quality: Basic Copying 1 Text mode Text/Photo mode The world’s coral reefs, where brilliantly colored fish and a myriad of other tropical creatures come together.
2 Place your original. Press (Image Quality) repeatedly until the desired type of original (TEXT, TEXT/ PHOTO, or PHOTO) appears. 100% AUTO PAPER TEXT 100% AUTO PAPER TEXT/PHOTO 100% AUTO PAPER PHOTO 3 Press (Light) or 01 01 01 1 Basic Copying 1 (Dark) to adjust the copy exposure. Move the indicator between (Light) and (Dark) below the display. Move to the left to make the exposure lighter or to the right to make the exposure darker. 4 Press (Start). Copying starts.
Automatic Adjustment of Exposure and Image Quality 1 1 Place your original. 2 Press . Basic Copying The indicator lights and exposure is automatically adjusted to the level best suited to the quality of the original. NOTE • The copy mode is set to Text automatically. • When scanning transparencies, adjust exposure using not operate correctly on transparent originals. 3 Press (Light) and (Dark) as the automatic exposure control may (Start). Copying starts.
Changing the Copy Ratio (Copy Ratio) You can set the machine to specify the copy ratio for a job. 1 NOTE . Basic Copying • If you want to make copies at the copy ratio of 100%, press Enlarging/Reducing Originals to a Standard Size (Preset Zoom) You can enlarge or reduce standard size originals to a standard paper size.
1 Place your original. 2 Press or to change the copy ratio. PRESET RATIO 141% A4➔A3 Basic Copying 1 3 Press (Start). Copying starts. NOTE • To return the copy ratio to 100%, press . • To cancel all settings and return the machine to the standby mode, press (Reset). Specifying the Copy Ratio by % (Zoom Designation) You can reduce or enlarge images by any copy ratio, in 1% increments. The available copy ratios are from 50% to 200%. Original Copy CITY CITY 1 Place your original.
Press (Start). Copying starts. NOTE • To return the copy ratio to 100%, press . • To cancel all settings and return the machine to the standby mode, press (Reset).
Collating Copies (Finisher) The Finisher mode can be selected to collate the copies in various ways by copy sets. 1 Below is a list of finishing functions and paper sizes available for each optional unit.
■ When Is Set Copies are automatically collated into sets arranged in page order, and output into the trays as follows: Originals Copy set 1 Copy set 2 Copy set 3 Three sets of copies specified 1 1 1 2 1 2 3 1 2 3 4 1 2 3 4 3 4 1 4 ■ When Is Set When originals of the same size are copied, the pages are aligned and the copy sets are output into the output trays in alternating directions.
■ When Is Set Copies are automatically collated into sets arranged in page order, stapled, and output into the trays, as shown below. Originals Copy set 1 Copy set 2 Copy set 3 Three sets of copies specified Basic Copying 1 1 1 1 2 1 1 3 1 1 4 Collating Copies into Sets in Page Order (Collate) This section explains the settings to perform each collation mode.
IMPORTANT • The function can be used when: - Rotatable paper is set both horizontally and vertically in the paper drawers - is set to for the paper drawer to be used in function. (See the Reference Guide) • When the Finisher-L1 is attached, Collation cannot be set. IMPORTANT • When the optional finisher is attached, Offset Collate mode is set automatically. • The Offset Collate can be set only with the optional finisher attached.
Collating Pages and Stapling (Staple) The Staple mode automatically collates the copies into sets arranged in page order, stapled, and output into the trays. IMPORTANT • Pull out the output auxiliary tray when stapling the A3- or B4-size paper. 1 Basic Copying 1 Place your original. 100% AUTO PAPER TEXT 2 Press lights.
Reserved Copying You can select copy settings and scan originals even if the machine is currently printing. Your scanned documents are processed after the current job is completed. 1 Basic Copying IMPORTANT • While the machine is warming up, at power on or after clearing the paper jam, it cannot scan the originals. NOTE • You can set a different mode for each job.
4 Once the original is scanned, remove it from the machine.
Interrupting the Current Job to Make Priority Copies (Interrupt Mode) The Interrupt mode enables you to interrupt the reserved or current job long enough to make higher priority copies. This mode is useful when making a rush copy during a long copy job. 1 Basic Copying NOTE • You can make interrupt copies when the machine is ready to scan. • You cannot set the copy mode for the interrupt copy during scanning. 1 Press (Interrupt). (Interrupt) lights.
4 Once the original is scanned, remove it from the machine. When the Interrupt copy job is completed, the interrupted printing operation resumes. Basic Copying 1 IMPORTANT • If you want to continue making Interrupt copies, wait until the current Interrupt copy job is completed (end of printing).
Useful Copy Functions 2 CHAPTER This chapter describes more advanced copy functions. Copying Facing Pages in a Book on Two Separate Sheets of Paper (Two-page Separation). . . . . . 2-2 Making Copies with Margins (Margin). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Erasing Shadows and Frame Lines from Copies (Frame Erase) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copying Facing Pages in a Book on Two Separate Sheets of Paper (Two-page Separation) The Two-page Separation mode enables you to copy facing pages in a book or a magazine onto separate sheets of paper. Original 2 Useful Copy Functions 1 Copy 1 IMPORTANT • When the machine is operating in the Two-page Separation mode, you cannot use the Binding Hole Erase and 2 on 1 Combination mode. • Place the original on the platen glass.
2 Press Special Features . The Special Features menu appears. SPECIAL FEATURES 1.2PG SEP SETTING Press or to select <1.2 PG SEP SETTING>, and press . SPECIAL FEATURES 1.2PG SEP SETTING When you press 4 Press press or 2 , the menu appears. to select <1.LEFT OPENING>, <2.RGHT OPENING>, or <3.OFF>, and . Set whether to start copying from the left page or right page according to whether the book starts from the left or right.
5 Press or to select the paper size for facing pages, and press ORIGINAL SIZE 6 . A3 Enter the desired copy quantity (1 to 99) using the numeric buttons. For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 1-7. ✱A4 100% TEXT Useful Copy Functions 2 7 Press 10 (Start). Copying starts. If you want to copy another facing-pages original, set it on the platen glass, and press (Start).
Making Copies with Margins (Margin) The Margin mode enables you to make copies with the entire original image shifted by a designated width to the left, right, top, or bottom to create a margin on the copies. Use this mode to make copies ready for placement in ring binders. Right margin selected Top margin selected Bottom margin selected 2 IMPORTANT • When the Margin mode is set, the entire original image is shifted to the left, right, top, or bottom by a selected width, then copied.
4 Press or to select where to set margin (<1.LEFT MARGIN>, <2.RIGHT MARGIN>, <3.TOP MARGIN>, <4.BOTTOM MARGIN> or <5.OFF>), and press . MARGIN TYPE 1.LEFT MARGIN 5 Press or to set the margin width, and press . You can also use the numeric buttons to enter the margin width. MARGIN WIDTH Useful Copy Functions 2 When you press 10mm , the standby display appears. NOTE • You can set the margin width in the range from 1 mm to 20 mm. • The default setting is 10 mm.
Erasing Shadows and Frame Lines from Copies (Frame Erase) The Frame Erase modes erase shadows and lines that appear when copying various types of originals. IMPORTANT ■ Original Frame Erase Erases the dark borders and frame lines that appear around the copy when the original is smaller than the selected paper size. Also, it creates a blank border around the edge of the copy.
■ Book Frame Erase Erases the dark border as well as center and contour lines that appear when copying facing pages in a bound original onto a single sheet of paper. Copy Original Book Frame Erase mode selected Useful Copy Functions 2 Book Frame Erase mode not selected Copy IMPORTANT • Set the book to be copied on the platen glass. • When the machine is operating in the Book Frame Erase mode, you cannot use the 2 on 1 Combination mode.
Making Copies Erasing the Frame of the Originals (Original Frame Erase) This section explains the settings to make copies erasing the Frame of the Originals. Before using this mode, set the width to be erased in the Additional Settings menu. (See “Setting the Standard Frame Erase Width,” on p. 3-7.) NOTE • You can set the Original Frame Erase width between 1 to 20 mm. • The default setting is <2 mm>. Place your original. 100% AUTO PAPER TEXT 2 Useful Copy Functions 1 2 Press Special Features 01 .
5 Press or to select the size of the original, and press ORIGINAL SIZE When you press . A3 , the standby display appears. NOTE • You can set the Original Frame Erase mode only on the original sizes shown on the display. • The machine selects the paper according to the original size you set in step 5 and the selected paper size is displayed. 2 6 Enter the desired copy quantity (1 to 99) using the numeric buttons.
Making Copies Erasing the Book Frame (Book Frame Erase) 1 Place your original, enter the Special Features menu, and open the menu. For details about the procedure above, see steps 1 to 3 of “Making Copies Erasing the Frame of the Originals (Original Frame Erase),” on p. 2-9. FRAME ERASE FEATURE 1.DOC. FRAME ERASE Press or to select <2.BOOK FRAME ERASE>, and press Useful Copy Functions 2 2 . FRAME ERASE FEATURE 2.
NOTE • You can set the book frame erase width in the range from 3 mm to 50 mm. • The default setting is 10 mm. • The machine selects the paper according to the original size you set in step 3 and the selected paper size is displayed. 5 Enter the desired copy quantity (1 to 99) using the numeric buttons. For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 1-7. 100% TEXT 2 Useful Copy Functions 6 Press ✱A3 01 (Start). Copying starts.
IMPORTANT • Do not place originals with binding holes in the feeder, as it may damage the originals. 2 Press or to select <3.HOLE PUNCH ERASE>, and press . FRAME ERASE FEATURE 3.HOLE PUNCH ERASE Press or to select the size of the original, and press ORIGINAL SIZE . 2 Useful Copy Functions 3 A3 NOTE • You can set the Binding Hole Erase mode only on the original sizes shown on the display. 4 Press or to select the binding hole erase width, and press .
5 Enter the desired copy quantity (1 to 99) using the numeric buttons. For details about entering the copy quantity, see “Specifying the Required Number of Copies,” on p. 1-7. 100% TEXT 6 Press ✱A3 05 (Start). Copying starts. 2 NOTE Useful Copy Functions • To cancel all settings and return the machine to the Standard mode, press (Reset). • If you press (Stop), the cancel job display appears.
Reducing Two Originals to Fit on a Single Copy Sheet (2 on 1 Combination) The 2 on 1 Combination mode automatically reduces two originals to fit on the selected paper size. Original Copy 1 1 2 2 IMPORTANT • When the machine is operating in the 2 on 1 Combination mode, you cannot use the Two-page Separation, Original Frame Erase, or Book Frame Erase modes. • You can set the 2 on 1 Combination mode only on the original sizes shown on the display.
4 Press or to select <1.ON> or <2.OFF>, and press . If you want to use the 2 on 1 Combination mode, select <1.ON>. If you do not want to use the 2 on 1 Combination mode, select <2.OFF>. 2 ON 1 SETTING 1.ON 5 2 Press or to select the size of the original, and press Useful Copy Functions ORIGINAL SIZE 6 Press or When you press A3 to select the paper size, and press SELECT PAPER SIZE . . A4 , the display returns to the standby mode.
Press (Start). When the original is placed on the platen glass, follow the instructions that appear on the display and press (Start) once for each original. When scanning is completed, press . Copying starts. NOTE • To cancel all settings and return the machine to the Standard mode, press (Reset). • If you press (Stop), the cancel job display appears. Select or using or . CANCEL COPYING? < YES NO > • If you press (Stop) after copying has started, some sheets of blank paper may be output.
Useful Copy Functions 2 2-18 Reducing Two Originals to Fit on a Single Copy Sheet (2 on 1 Combination)
Setting/Storing Specifications of the Copy Function 3 CHAPTER This chapter describes how to store or change the default settings to suit your needs. Copy Settings List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Changing the Current Standard Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Setting the Standard Exposure . . . . . . . . . . . . . . . . . .
Copy Settings List The following items can be stored or set in the Copy Settings menu. Additional Function Available Settings Applicable page COPY SETTINGS 1.STANDARD EXPOSURE Setting/Storing Specifications of the Copy Function 3 MANUAL*(-LT – DK+:9 steps, 5*)/AUTO 3-3 2.STD ZOOM RATIO 50 – 200% (100%*) 3-5 3.STANDARD COPY QTY 01* – 99 3-6 4.FRAME ERASE WIDTH 01 – 20 mm (02 mm*) 3-7 5.AUTO SORT ON*/OFF 3-8 6.SORT ROTATE ON*/OFF 3-9 7.SHARPNESS 1 – 9 (5*) 3-10 8.
Changing the Current Standard Settings Standard Settings refers to a combination of Copy modes that the machine automatically applies at power on or when (Reset) is pressed. In this section, the procedure for changing the Copy modes stored as the Standard Settings is explained.
3 Press or to select <1.STANDARD EXPOSURE>, and press . COPY SETTINGS 1.STANDARD EXPOSURE When you press 4 Press or , the menu appears. to select , and press . STANDARD EXPOSURE MANUAL 3 5 Press or to set the desired standard copy exposure, and press . Setting/Storing Specifications of the Copy Function For details about the adjustment of the copy exposure, see “Adjusting Copy Exposure,” on p. 1-11. STANDARD EXPOSURE -LT DK+ When you press menu.
Setting the Standard Zoom Ratio You can set the standard zoom ratio. NOTE • The default setting is <100%>. 1 Enter the Additional Functions menu and open the <2.COPY SETTINGS> menu. For details about the procedure above, see steps 1 and 2 in “Setting the Standard Exposure,” on p. 3-3. COPY SETTINGS 1.STANDARD EXPOSURE Press or to select <2.STD ZOOM RATIO>, and press Setting/Storing Specifications of the Copy Function 2 3 . COPY SETTINGS 2.
Setting the Standard Copy Quantity You can set the standard copy quantity. NOTE • The default setting is <01>. 1 Enter the Additional Functions menu and open the <2.COPY SETTINGS> menu. For details about the procedure above, see steps 1 and 2 in “Setting the Standard Exposure,” on p. 3-3. 2 3 Press or to select <3.STANDARD COPY QTY>, and press . Setting/Storing Specifications of the Copy Function COPY SETTINGS 3.
Setting the Standard Frame Erase Width You can set the standard frame erase width for Frame Erase function. NOTE • The default setting is <02 mm>. 1 Enter the Additional Functions menu and open the <2.COPY SETTINGS> menu. For details about the procedure above, see steps 1 and 2 in “Setting the Standard Exposure,” on p. 3-3. 2 Press or to select <4.FRAME ERASE WIDTH>, and press . 3 When you press 3 Press or Setting/Storing Specifications of the Copy Function COPY SETTINGS 4.
Setting the Automatic Collate On/Off This mode allows automatic selection of the Collate (Offset Collate) mode when the original is placed in the feeder. This is helpful when making multiple copies, because you do not need to remember to select the Finisher mode. NOTE • The default setting is . • This function is available only when the Feeder (ADF-J1) is attached. 1 Enter the Additional Functions menu and open the <2.COPY SETTINGS> menu.
Setting the Rotate Collate On/Off This mode allows automatic selection of the Rotate Collate mode when the original is placed in the feeder. For details about the Rotate Collate, see pages 1-8 and 1-9.
Setting the Sharpness You can set the sharpness of the copied image. When you want to copy texts and lines clearly, increase the sharpness level. If you want to copy a halftone original such as a picture, decrease the sharpness level. ■ Sharpness level low If you make copies of an original containing halftones, such as a printed photograph, using the Photo mode, moire may occur. You can soften the moire effect by adjusting the sharpness level lower.
1 Enter the Additional Functions menu and open the <2.COPY SETTINGS> menu. For details about the procedure above, see steps 1 and 2 in “Setting the Standard Exposure,” on p. 3-3. 2 Press or to select <7.SHARPNESS>, and press . COPY SETTINGS 7.SHARPNESS When you press 3 Press or , the menu appears. to set the desired sharpness level, and press 3 . Setting/Storing Specifications of the Copy Function To copy an original in text and lines, select a high sharpness level.
Setting the Prescan Function This function allows you to save the first copy time, by making the machine get ready to start copying before you press (Start). NOTE • If is set to , the machine gets ready to start copying from the moment you set the original in the feeder or on the platen glass. • The factory setting is . 1 Enter the Additional Functions menu and open the <2.COPY SETTINGS> menu.
Appendix 4 CHAPTER Chart of Available Combination of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chart of Available Combination of Functions ✕ ✕ ✕ ✕ ✕ Automatic Exposure Control Photo ✕ Text ✕ ✕ ✕ ✕ Text/Photo ✕ ✕ ✕ ✕ Automatic Paper Selection Stack Bypass ✕ ✕ ✕ Collate Rotate Collating ✕ Offset Collating ✕ ✕ Staple ✕ ✕ ✕ Interrupt Copy Reserve Copy 4-2 Chart of Available Combination of Functions ✕ ✕ ✕ Reserve Copy Interrupt Copy Staple Offset Collating Rotate Collating Collate Stack Bypass Automatic Paper Selection Text/Photo Text ✕ Enlargement Zoom Designation Append
Reserve Copy Interrupt Copy Staple Offset Collating Rotate Collating Collate Stack Bypass Automatic Paper Selection Text/Photo Text Photo Zoom Designation Enlargement Automatic Exposure Control : Combination available ✕: Combination unavailable Two-page Separation ✕ 2 on 1 Combination Original Frame Erase Book Frame Erase Binding Erase Right Margin Left Margin Top Margin Bottom Margin Appendix Bottom Margin Top Margin Left Margin Right Margin Binding Erase Book Frame Erase Original F
✕ ✕ Book Frame Erase ✕ ✕ ✕ Bottom Margin Top Margin Left Margin Right Margin Binding Erase ✕ ✕ ✕ Original Frame Erase Binding Erase Book Frame Erase Original Frame Erase ✕ Two-page Separation 2 on 1 Combination 2 on 1 Combination Two-page Separation : Combination available ✕: Combination unavailable ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Right Margin Left Margin ✕ Top Margin ✕ ✕ ✕ ✕ Bottom Margin ✕ ✕ ✕ ✕ Appendix 4 4-4 Chart of Available Combination of Functions
A Index Numerics 2 on 1 Combination ..................................................................................................................2-15 A Auto Collate ................................................................................................................................3-8 Auto Paper Selection .................................................................................................................1-8 4 Appendix B Binding Erase ..........................................
I Image Quality ...........................................................................................................................1-12 Interrupt Mode ..........................................................................................................................1-25 M Manual Paper Selection .............................................................................................................1-9 Margin ................................................................................
Z Zoom ........................................................................................................................................1-15 Zoom Designation ....................................................................................................................
Appendix 4 4-8 Index
