Installation Procedure Canon BW PCL PRINTER KIT-J1 Sep 14 2005
Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality. Corrections This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.
Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems. Indicates an item requiring disconnection of the power plug from the electric outlet.
Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accom- panies the symbol , the arrow indicates the direction of the electric signal.
Contents Contents Chapter 1 Installation Procedure 1.1 Checking components ....................................................................................................................................... 2 1.1.1Checking the Contents................................................................................................................................. 2 1.2 Installation procedure..................................................................................................................
Contents
Chapter 1 Installation Procedure
Chapter 1 1.1 Checking components 1.1.1 Checking the Contents 0010-7372 [2] [1] [4] [3] [6] [5] F-1-1 2 [1] 32MB ROM 1 pc. [2] 256MB RAM 1 pc. [3] Screw (binding; M3X4) 1 pc. [4] User software CD-ROM 1 pc. [5] Release Note 1 pc. [6] User's Manual CD-ROM 1 pc.
Chapter 1 1.2 Installation procedure SDRAM and the super capacitor remain powered to back up the image memory (even after the main power 1.2.1 Mounting to the Host Machine If an optional Super G3 Fax Board-T1 is found, the switch has been turned off and the power plug has 0010-7632 1) Turn off the main power switch, and disconnect the been disconnected). Be sure to disconnect the IP modem cable before removing the RAM. power plug. 2) Remove the rear cover [1].
Chapter 1 [2] [1] [B] [A] [B] [2] [1] F-1-6 [3] F-1-8 7) If a UFRII LT PRINTER KIT-J2 is installed, perform steps 7-1) and 7-2). 8) Disconnect the soft ID cable [1]. 7-1) Remove the LAN cover [1]. - 1 cable clamp [2] - 4 screws [2] [2] [2] F-1-9 [1] [2] F-1-7 7-2) Disconnect the connector [1] of the IP-LAN cable. - 1 wire saddle [2] 9) Release the claw [1] of the cable guide, and free the cable guide [2] in upward direction.
Chapter 1 10) Remove the IP cover [1]. - 10 screws [2] [2] [2] [2] [1] [3] F-1-13 13) Attach the IP cover you removed in step 10). [1] [2] F-1-11 11) Shift the 2 locking levers [1] back to their initial position. When attaching the IP cover, take care not to damage the grounding plate [2] by the USB port [1]. Also, after attaching the IP cover, check to make sure that the grounding plate is in firm contact with the USB port.
Chapter 1 UFRII LT PRINTER KIT-J2 is mounted) G3 Fax Board-T1 is mounted) - rear left cover - rear cover When attaching the LAN cover, take care not to damage the grounding plate [2] by the LAN port [1]. Also, after attaching the LAN cover, check to make sure that the grounding plate is in firm contact with the 18) Connect the power plug, and turn on the main power switch. 1.2.2 Checking the Connection LAN port.
Sep 14 2005
