Installation Procedure Canon BW UFRII LT PRINTER KIT-J2 Sep 14 2005
Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality. Corrections This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.
Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems. Indicates an item requiring disconnection of the power plug from the electric outlet.
Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accom- panies the symbol , the arrow indicates the direction of the electric signal.
Contents Contents Chapter 1 Installation Procedure 1.1 Checking components ....................................................................................................................................... 2 1.1.1Checking the Contents................................................................................................................................. 2 1.2 Installation procedure..................................................................................................................
Contents
Chapter 1 Installation Procedure
Chapter 1 1.1 Checking components 1.1.1 Checking the Contents 0010-7374 [1] [2] [3] [7] [6] [5] [4] [9] [8] F-1-1 [1] LAN cover 1 pc. [6] User Software CD-ROM 1 pc. [2] LAN PCB 1 pc. [7] User Manual CD-ROM 1 pc. [3] IP-LAN cable 1 pc. [8] Release Note 1 pc. [4] Wire saddle 1 pc. [9] Network Quick Start 1 pc. Guide [5] 2 TP screw (3x8) 8 pc.
Chapter 1 1.2 Installation procedure [2] 1.2.1 Mounting to the iR Machine 0010-7487 1) Turn off the main power switch, and disconnect the power plug from the power outlet. 2) Remove the machine's rear cover [1]. - 4 screws [2] [1] [2] F-1-4 5) Connect the LAN board and the IP board. - 1 IP-LAN cable [1] [2] [1] [1] F-1-2 3) Cut off the area [2] of the rear cover [1] indicated F-1-5 in the figure using nippers.
Chapter 1 - 4 TP screws (3x8) [2] [3] [2] [2] [1] [2] F-1-7 [1] F-1-9 Points to Note When Attaching the LAN Cover A grounding wire is fitted to the IP machine's IP PCB and IP cover. When attaching the LAN cover, be sure to remove the screw [1] from the wire, and tighten the 8) Put back the machine's rear cover you removed in step 2). 9) Connect the user's LAN cable to the machine. screw over both the wire and the LAN cover [2].
Chapter 1 User Mode key >2 > 8 > User Mode key [#SSSW] appears. 2) Press [<-] 5 times. When [REPORT] has appeared, press [OK]. 3) Press [+>] once. When [REPORT OUTPUT] has appeared, press [OK]. 4) Press [+>] 5 times. When [SPEC LIST] has appeared, press [OK]. 5) See that a SPEC REPORT is printed out. Check to be sure that 'BDL-IMAGE' is 'ON'. MEMO: "SPEC REPORT" - If 'TOTAL MEMORY' is 128 MB, be sure 'BDL-IMAGE (600)' is 'ON'. - If 'TOTAL MEMORY' is 256 MB, be sure 'BDL-IMAGE (1200)' is 'ON'.
Sep 14 2005