Service manual

Chapter 13
13-4
13.3.3 Jam Codes (Related to ADF)
0011-2839
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
T-13-5
13.3.4 Jam Codes (Related to Duplex Unit)
0011-2840
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
T-13-6
13.3.5 Jam Codes (Related to Inner 2-way Tray)
0011-2850
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
T-13-7
13.4 Finisher Error Codes
13.4.1 Error Code Details
0011-2652
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
T-13-8
Code Name Sensor No. Description
0000 Unknown jam - Other errors
0007 Initial stationary PI6,PI7,PI8 Paper is detected in the transport path before the DADF starts initial
operation.
0008 Read sensor delay PI7,PI8 The read sensor does not detect paper when the paper has been fed
by the predetermined distance since reception of a pickup request.
0009 Read sensor stationary PI7 The trailing edge of paper is not detected when the paper has been
fed by the predetermined distance since detection of it by the read
sensor.
000a Paper absence (Pull out
the document.)
PI11 The Document set sensor has been held off since start of pickup.
000c Delivery reversal sensor
delay
PI6,PI7 The delivery reversal sensor does not detect paper since the paper
has been fed by the predetermined distance since the read sensor
was turned on.
000d Delivery reversal sensor
stationary
PI6 The trailing edge of paper is not detected when the paper has been
fed by the predetermined distance since the delivery reversal sensor
detected the paper.
000e ADF cover open PI10 The feeder cover was opened during operation (of the drive system).
000f User ADF open sensor of
the reader
unit
The ADF was opened during operation (of the drive system).
0010 Pickup NG - The registration sensor has been held off since paper pickup started.
Code Name Sensor No. Description
0120 Delay jam at duplex
paper sensor 1
SR1002 The duplex paper sensor 1 does not turn on within the specified
time after the delivery sensor on the main unit side turns on.
0124 Delay jam at duplex
paper sensor 2
SR1003 The duplex paper sensor 2 does not turn on within the specified
time after the duplex reverse motor starts.
0221 Stationary jam at
duplex paper sensor 1
SR1002 - The duplex paper sensor 1 does not turn off when the specified
time has lapsed since the duplex paper sensor 2 turned on.
- The duplex paper sensor 1 does not turn off when the paper
with a longitudinal length of 280 mm reaches the standby
position (about 90 mm from the duplex paper sensor 2).
0228 Stationary jam at
duplex paper sensor 2
SR1003 The duplex paper sensor 2 does not turn off when the specified
time has lapsed since the feed motor started.
Code Name Sensor No. Description
010e Delay jam at No.2
delivery section
SR1101 The No.2 delivery sensor does not detect presence of paper within
the specified time after turning on of the fixing delivery sensor.
0212 Stationary jam at No.2
delivery section
SR1101 Absence of paper is not detected within the specified time after
turning on of the No.2 delivery sensor.
Display
code
Detail
Code
Main Cause/Symptom Countermeasure
E500 0001 Finisher communication error
Data communication could not be
performed normally. It has been retried
three times in vain.
- Check the connectors of the finisher controller
PCB and DC controller PCB for normal connection.
- Replace the finisher controller PCB.
- Replace the DC controller PCB.