Service manual

Chapter 14
14-19
This value is used when automatic scan position adjustment (TESTMODE>"2"SCAN TEST>"3"SHEET POS ADJ) fails.
14.6.4 <026:Distance from the standby position of CIS to the shading start point>
0011-2004
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
White shading can be adjusted finely.
Normally, do not change the setting value. If any operation error occurs after changing the setting value, change the setting value to the original one.
14.6.5 <031Vertical scan start position adjustment>
0011-2005
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which vertical scanning of a book starts. The larger the adjustment value, the narrower the left-side margin of the image becomes.
14.6.6 <032Horizontal scan start position adjustment>
0011-2007
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which horizontal scanning of a book starts. The larger the adjustment value, the narrower the top margin in the image becomes.
14.6.7 <033Vertical scan magnification correction>
0011-2008
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Correct the magnification of vertical scanning of a book. The larger the adjustment value, the more the image stretches in the vertical scanning direction.
14.6.8 <035: - 036:Reader motor speed change>
0011-2010
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Though no market adjustment work needs to be carried out, enter factory defaults at image processor PCB replacement.
14.6.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)>
0011-2011
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which vertical scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the left-side margin of the
image becomes.
14.6.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)>
0011-2017
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which horizontal scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the top margin of the image
becomes.
14.6.11 <043: Horizontal scan end position correction (copy)>
0011-2020
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which horizontal scanning of a document being copied ends. The larger the adjustment value, the narrower the bottom margin of the image
becomes.
14.6.12 <044: Horizontal scan end position correction (superfine)>
0011-2021
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which horizontal scanning of a FAX document scanned in superfine mode ends. The larger the adjustment value, the narrower the bottom
margin of the image becomes.
14.6.13 <045: Horizontal scan end position correction (fine)>
0011-2022
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which horizontal scanning of a FAX document scanned in fine mode ends. The larger the adjustment value, the narrower the bottom margin
of the image becomes.
14.6.14 <046: Horizontal scan end position correction (standard)>
0011-2024
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Adjust the position at which horizontal scanning of a FAX document set to the standard scan resolution ends. The larger the adjustment value, the narrower the
bottom margin of the image becomes.
14.6.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)>
0011-2025
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Correct the magnification of vertical scanning of a document fed from the ADF. The larger the adjustment value, the more the image stretches in the vertical scan-
ning direction.
14.6.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)>
0011-2027
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Correct the magnification of horizontal scanning of a document fed from the ADF. The smaller the adjustment value, the more the image stretches in the horizontal
scanning direction.
This menu is used to adjust the ADF feed motor speed. If you changed the adjustment value in this mode, the adjustment value selected for SCAN NUMERIC>54
must also be incremented/decremented by the same amount.