Service manual

Chapter 14
14-21
14.7.1.1.2 Detailed Discussions of Bit 7
0011-1862
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to enable/disable placement of priority on recording in sub scanning direction.
T-14-19
*: Image B4 or shorter and that cannot be printed by division and on A4 recording paper.
14.7.1.2 SSSW-SW14
14.7.1.2.1 List of Functions
0011-1884
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
T-14-20
14.7.1.2.2 Detailed Discussions of Bit 0
0011-1885
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable transfer bias pressure reduction mode.
Select "Enable" to avoid image defects (black spots) produced by transfer bias leaks occurring in a low-pressure region, such as one at a high altitude. This setting
regulates the transfer bias to keep it from exceeding a predetermined level during printing.
14.7.1.2.3 Detailed Discussions of Bit 1
0011-1888
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable developing assembly idling mode. Select "Enable" to drive the main motor for a specified period of time to apply idling and
developing bias (AC + DC) to prevent the thinning of the image density when the unit is installed or the developing unit is replaced in a low-temperature, low-
humidity region. This mode works only on a new developing assembly and before a toner cartridge is loaded.
14.7.1.2.4 Detailed Discussions of Bit 2
0011-1889
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable black belt addition mode. If the user uses paper that causes fixed toner on paper to be fused and adhered to drum, selecting
"Yes" will clean the drum by forming a black band on the drum surface during the reverse rotation which is performed after printing on 50 sheets.
Implementation of this mode could result in a drum life falling short of its life expectancy.
14.7.1.2.5 Detailed Discussions of Bit 3
0011-1890
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable post-rotation reduction mode. Selecting "Enable" will reduce the noise caused by the polygon motor by stopping the motor
immediately after post-rotation.
14.7.1.2.6 Detailed Discussions of Bit 4
0011-1891
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable flicker reduction mode. Select "Enable" and enter a count to modify fusing temperature control to cancel fluorescent flicking
during printing.
Implementation of this mode would degrade the throughput.
5 not used - -
6 not used - -
7 priority on recording in sub scanning direction place do not place
place: if B4 recording paper and A4 recording paper are set and an A4 extra-long image
(*) is received, printing will be on the B4 recording paper.
do not place: if B5 horizontal recording paper and A4 recording paper are set and a B4 image is
received, printing will be by division and on B5 horizontal recording paper.
Bit Function 1 0
0 Transfer bias pressure reduction mode Enable Disable
1 Developing assembly idling mode Enable Disable
2 Black belt addition mode Enable Disable
3 Post-rotation reduction mode Enable Disable
4 Flicker reduction mode Enable Disable
5 Silent mode Enable Disable
6 Terminal temperature rise noise reduction mode Enable Disable
7 Not used - -
Bit Function 1 0