Service manual

Chapter 14
14-22
14.7.1.2.7 Detailed Discussions of Bit 5
0011-1892
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable silent mode. Select "Enable" to modify the registration loop amount and thus reduce noises or squeaks the registration rollers
produce after picking paper from the individual paper inlets.
14.7.1.2.8 Detailed Discussions of Bit 6
0011-1894
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to enable or disable noise reduction mode during terminal temperature rises. Select "Enable" to start slowdown at a temperature lower than normal
when printing on smaller-sized paper than B4. Slowdown control thus enabled prevents the thermal degradation of the fusing film grease, assuring smooth sliding
among the fixing film, heater and film guide to cut squeaks.
14.7.1.3 SSSW-SW15
14.7.1.3.1 List of Functions
0011-1895
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
T-14-21
14.7.1.3.2 Detailed Discussions of Bit 0
0011-1896
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to inhibit automatic delivery tray replacement while running jobs with an inner two-way tray mounted in position. Select "Enable" to inhibit auto-
matic tray replacement.
14.7.1.3.3 Detailed Discussions of Bit 1
0011-1897
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to halt stapling job when a finisher installed has run out of staples. Select "Enable" to halt staple jobs when the finisher has run out of staples.
14.7.1.3.4 Detailed Discussions of Bit 2
0011-1898
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Select whether to display a tray full message when the maximum allowable stapled document count is exceeded with a finisher installed. Select "Enable" not to
display the message.
14.7.2 Numerin Parameter Settings (Numeric Prama.)
14.7.2.1 List of Functions
0011-1900
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Bit Function 1 0
0 Inhibit automatic delivery tray replacement while running
jobs
Enable Disable
1 Halt stapling job when out of staples Enable Disable
2 Inhibit tray full indication while the stapled document
count is exceeded
Enable Disable
3 Not used - -
4 Not used - -
5 Not used - -
6 Not used - -
7 Not used - -
No. Function Default Setting range
01: - 30: Not used
31: Top registration adjustment (manual feed tray) 50 0 to 100, one unit = 0.1 mm
32: Top registration adjustment (cassette) 50 0 to 100, one unit = 0.1 mm
33: Top registration adjustment (duplex unit) 50 0 to 200, one unit = 0.1 mm
34: Left-end registration adjustment (manual feed tray) 100 0 to 200, one unit = 0.1 mm
35: Left-end registration adjustment (cassette 1) 100 0 to 200, one unit = 0.1 mm
36: Left-end registration adjustment (cassette 2) 100 0 to 200, one unit = 0.1 mm
37: Left-end registration adjustment (cassette 3) 100 0 to 200, one unit = 0.1 mm
38: Left-end registration adjustment (cassette 4) 100 0 to 200, one unit = 0.1 mm
39: Left-end registration adjustment (duplex unit) 100 0 to 200, one unit = 0.1 mm
40: Target fixing temperature adjustment (multi) 6 -30 to 0, one unit = 5 deg C
41: Target fixing temperature adjustment (cassette 1) 6 -30 to 0, one unit = 5 deg C
42: Target fixing temperature adjustment (cassette 2) 6 -30 to 0, one unit = 5 deg C
43: Target fixing temperature adjustment (cassette 3) 6 -30 to 0, one unit = 5 deg C
44: Target fixing temperature adjustment (cassette 4) 6 -30 to 0, one unit = 5 deg C