User Guide

ManualsBrandsCanon ManualsOtheriR5800C, iR5800CN, iRC6800C, iRC6800CN

(1/6)

Canon Service Bulletin COPIER

Issued by Canon Europa N.V.

Location:

Service Manual (Maintenance>Adjustment)

Subject:

Addition of Descriptions on Service Mode

Particulars:

The Service Manual is being updated by adding descriptions of service mode items, designed as remedies to

implement in the event of stacking faults; these mode items consist of the following:

- upward curl mode

- special curl mode

- heavy paper downward curl mode

- heavy paper upward curl mode

- stack delivery mode

The new descriptions are as follows:

1. Upward Curl Mode

a. Outline

Paper tends to curl upward in certain conditions, preventing normal delivery/stacking. (See the following figure.)

F-1

Model:

Finisher-R1

Saddle Finisher-R2

Ref No.:

Acc-406

(F3-T01-00W-10029-01)

Date:

30-07-04

Summary of content (6 pages)

PAGE 1
Canon Service Bulletin COPIER Issued by Canon Europa N.V. Model: Ref No.
PAGE 2
Acc-406 If such is the case, 1) Turn over the stack of paper inside the paper source (e.g., cassette). If doing so makes the upward curling worse than before, turn back over the stack. If the paper still develops upward curl and, thus, fails to deposit itself normally, try enabling the upward curl mode item. b. Enabling the Upward Curl Mode 1) Turn off the host machine. 2) Set the bits of SW104 on the finisher controller PCB as follows: ON 1 2 3 4 5 6 7 8 F-2 3) Turn on the host machine.
PAGE 3
Acc-406 If this is the case, 1) Turn over the stack of paper inside the source (i.e., cassette). If paper starts to curl more than before, turn back over the stack. If the curling is not corrected as a result, try enabling the special curl mode item. b. Enabling Special Curl Mode 1) Turn off the host machine. 2) Set the bits of SW104 on the finisher controller PCB as follow: ON 1 2 3 4 5 6 7 8 F-4 3) Turn on the host machine.
PAGE 4
Acc-406 If this is the case, 1) Turn over the stack of paper in the source (i.e., cassette). If doing so has caused the paper to curl downward much more than before, turn back over the stack. If the machine fails to stack paper because of downward curl, try enabling the heavy paper downward curl mode. b. Enabling Heavy Paper Downward Curl Mode 1) Turn off the host machine. 2) Set the bits of SW104 on the finisher controller PCB as follows: ON 1 2 3 4 5 6 7 8 F-6 3) Turn on the host machine.
PAGE 5
Acc-406 If this is the case, 1) Turn over the stack of paper in the source (i.e., cassette). If doing so has caused the paper to curl more than before, turn back over the stack. If the curling is still appreciable and the machine fails to stack the paper properly, try enabling heavy paper upward curl mode. b. Enabling Heavy Paper Upward Curl 1) Turn off the host machine. 2) Set the bits of SW104 on the finisher controller PCB as follows: ON 1 2 3 4 5 6 7 8 F-8 3) Turn on the host machine.
PAGE 6
Acc-406 If this is the case, 1) Turn over the stack of paper inside the source (e.g., cassette). If doing so has made upward curling worse than before, turn back over the stack. If the upward curling still causes the machine to fail to stack the paper correctly, try enabling stack delivery mode: b. Enabling Stack Delivery Mode 1) Turn off the host machine. 2) Set the bits of SW104 on the finisher controller PCB as follows: ON 1 2 3 4 5 6 7 8 F-10 3) Turn on the host machine.