Service Manual Finisher, Sorter, DeliveryTray Additional Finisher Tray-A1 Dec 10 2003
Application This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair of products. This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does not apply to your locality. Corrections This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.
Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems. Indicates an item requiring disconnection of the power plug from the electric outlet.
Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation. In the diagrams, the arrow represents the path of mechanical drive; where a signal name accompanies the symbol , indicates the direction of the electric signal.
Contents Contents Chapter 1 Specifications 1.1 Product Specifications....................................................................................................................................... 1- 1 1.1.1Specifications .............................................................................................................................................. 1- 1 1.2 Names of Parts...................................................................................................................
Chapter 1 Specifications
Contents Contents 1.1 Product Specifications........................................................................................................................................ 1-1 1.1.1 Specifications .............................................................................................................................................. 1-1 1.2 Names of Parts............................................................................................................................................
Chapter 1 1.1 Product Specifications 1.1.1 Specifications 0004-8823 T-1-1 Item Specifications Stacking Face up / Face down Remarks orientation Stacking size A3, A4, A4R, A5, A5R, B4, B5, B5R, postcard, 279 mm x 432 mm (11 x 17), LGL, LTR, LTRR, STMT, STMTR, elongation size Feed direction: 139.7 to 482.6 mm: cross feed direction: 98.4 to 330.
Chapter 1 1.2 Names of Parts 1.2.
Chapter 2 Functions
Contents Contents 2.1 Basic Construction ............................................................................................................................................. 2-1 2.1.1 Functional Construction ..............................................................................................................................
Chapter 2 2.1 Basic Construction 2.1.1 Functional Construction 0004-9190 The additional finisher tray is optionally installed in the tray 1 of the finisher. Additional finisher tray paper sensor (PI44) are provided to detect the presence of the paper stacked on the tray.
Chapter 3 Installation
Contents Contents 3.1 Making Pre-Checks ............................................................................................................................................ 3-1 3.1.1 Checking the Contents................................................................................................................................. 3-1 3.1.2 Installing the Accessories ........................................................................................................................... 3-2 3.
Chapter 3 3.1 Making Pre-Checks 3.1.1 Checking the Contents 0003-2135 [1] [6] [7] [8] [12] [2] [12] [10] [9] [12] [4] [11] [11] [3] [12] [5] F-3-1 T-3-1 [1]Additional finisher tray 1 pc. [7]Sensor unit 1 pc. [2]Slide guide 1 pc. [8]Sensor cable 1 pc. [3]Front tray stay 1 pc. [9]Sensor unit cover 1 pc. [4]Rear tray stay 1 pc. [10]Settings label 1 pc. [5]Front tray stay cover 1 pc. [11]Screw (tapping; M4x12) 2 pc. [6]Rear tray stay cover 1 pc.
Chapter 3 3.1.2 Installing the Accessories 0003-2136 If you are installing other accessories at the same time as the additional finisher tray, be sure to install the host machine and then the accessories in the following order: 1.Side paper deck (See the Side Paper Deck Installation Procedure.) 2.Finisher [1], [2] (See “Preparing the Host Machine for Installation” in the Finisher/Saddle Finisher Installation Procedure.) 3.
Chapter 3 3.Disconnect the host machine’s power plug (from the power outlet).
Chapter 3 3.2 Unpacking Installation and 3) In the case of the Finisher-Q1/R1, remove the 3 screws [1], and detach the rear cover [2]. [2] 3.2.1 Installation Procedure 3.2.1.1 Installation 0003-2137 1) In the case of the Finisher-Q1/R1, open the front door [1], remove the 3 screws [2], and detach the front cover [3]. [1] F-3-5 [1] 4) In the case of the Saddle Finisher-Q2/R2, detach [2] the cable cover [1], remove the 6 screws [2], and detach the rear cover [3].
Chapter 3 [2]. [1] [2] [1] [3] F-3-9 8) Remove the 2 screws [1], and detach the grounding wire [2] and the cable fixing plate [3]; then, [2] F-3-7 disconnect the 2 connectors [4]. [4] [2] [3] [1] 6) Remove the screw [1], and detach the slide guide stopper [2]; then, slide the slide guide [3] upward to detach. [1] [3] [2] F-3-10 9) Slide the No. 1 tray upward to detach. F-3-8 10) Remove the 4 screws [1], and detach the tray 7) Remove the screw [1], and detach the tray stopper cover.
Chapter 3 11) Cut off the face cover [2] of the tray cover using [1] nippers. [2] To eliminate the possibility of injury upon contact with the tray, be sure that the cut edge on the tray cover will be smooth without burrs when cutting off the face cover. [1] [2] F-3-13 14) Fit the tray cover of the No. 1 tray using 4 screws. F-3-11 12) Fit the front tray stay [1] to the No. 1 tray using 2 screws [2] (binding; M4x6).
Chapter 3 (binding; M4x6). [1] [1] [2] [2] F-3-17 18) Mount the rear tray stay cover [1] using a screw F-3-15 [2] (tapping; M4x12). 16) Route the sensor cable [3] through the edge saddle [1] and the cable clamps [2]. Join the connector [4] to [1] [2] the sensor [5] and the another connector [6] to the connector [7] of the No. 1 tray. [3] [1] [4] [2] [5] F-3-18 [6] 19) Mount the sensor unit cover [1] using a screw (binding; M4x6).
Chapter 3 [1] [2] [1] [3] F-3-19 20) Attach the No. 1 tray from above, and lower it by releasing the latch [1] at the back of the No. 1 tray. At this time, be sure to lower the No. 1 tray while pushing up the shutter [2] and the stack delivery gate [3] at the delivery outlet is covered. [2] F-3-20 The stack delivery gate comes off from the finisher when the No. 1 tray is lowered without raising the shutter at the delivery outlet.
Chapter 3 [1] [2] [1] [2] [1] [2] [3] F-3-22 F-3-21 24) Slide-in the slide guide from top, which is contained in the carton box, to the finisher; then fix the slide guide stopper removed at the step 6 in place 21) Mount the tray stopper removed at the step 7 using using a screw. a screw. 22) Connect the 2 connectors of the No. 1 tray to the finisher controller PCB; then, fix the grounding wire Pay attention not to confuse the included slide guide and the slide guide found on the finisher.
Chapter 3 screw. The additional finisher tray detecting plate must be fixed in place by taking measurements where the vertical face of the finisher is smooth without a protrusion (indicated in the figure). [3] [2] 2mm [1] F-3-23 25) Mount the upper left cover, rear cover, and front cover (in the case of the Finisher-Q1/R1) of the finisher. 26) Free the latch of the No. 1 tray and move it down so that the additional finisher tray [1] is as shown in the figure.
1m m Chapter 3 [1] F-3-25 3-11
Dec 10 2003
