Multimedia Projector LV-7225 LV-7220 LV-5220 Owner’s Manual E English
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆ Wide Zoom Lens ◆ Brightness of the projection lamp can be selected in the Setting menu. (See page 45.) This projector is equipped with Wide Zoom Lens which is 1.
Table of Contents Features and Design . . . . . . . . . . . . . . . . . . .2 Table of Contents . . . . . . . . . . . . . . . . . . . . . .3 To the Owner . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety Instructions . . . . . . . . . . . . . . . . . . . .5 Computer Input . . . . . . . . . . . . . . . . . . . . .
To the Owner Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. This projector should be operated only from the type of power source indicated on the marking label.
Safety Instructions Air Circulation Installing the Projector in Proper Position Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20˚ Do not tilt the projector more than 20 degrees above and below. CAUTION 20˚ Hot air is exhausted from the exhaust vent.
Compliance Federal Communication Commission Notice Multimedia Projector, Model :LV-7225E,LV-7225U,LV-7220E,LV-7220U,LV-5220E and LV-5220U This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Part Names and Functions Front q w q Focus Ring w Speaker e r t y u i Power Cord Connector Infrared Remote Receiver Zoom Lever Projection Lens Lens Cover (See page 50 for attaching.) Air Intake Vent o Top Controls and Indicators !0 Air Intake Vent !1 Terminals and Connectors e Back r !6 o ty u i !0 !1 !2 Air Intake Vent (back and bottom) !3 Air Filter !4 Adjustable Feet !5 Lamp Cover !6 Exhaust Vent CAUTION Hot air is exhausted from the exhaust vent.
Part Names and Functions Part Names and Functions Rear Terminal q e w DVI - I / RGB IN-1 r t y AUDIO R ✽ IN L VIDEO IN SERVICE PORT S-VIDEO IN COMPUTER AUDIO IN RESET AUDIO OUT MCI RGB IN-2 / COMPONENT IN / RGB OUT Do not press this button. This button is used for optional accessories. o i u q DVI-I/ RGB IN-1 Connect output signal from a computer (Digital/Analog DVI-I type) or Multi Card Imager (optional) to this terminal.
Part Names and Functions Top Control q w r e MENU POWER SET VOL - VOL + AUTO SET LAMP REPLACE WARNING y t INPUT i u q MENU button Opens or closes the On-Screen Menu. (p22) w SET button Executes the item selected. It is also used to expand/ compress the image in Digital zoom +/– mode. (p34) e AUTO SET button Corrects vertical keystone distortion and adjusts computer display parameters including Fine sync, Total dots and Picture position. (p24, 42) r POWER button Turns the projector on or off.
Part Names and Functions Part Names and Functions q L-CLICK button Remote Control Unit Acts as left click for wireless mouse operation. (p13) w SIGNAL EMISSION indicator This indicator lights red while the laser beam is being emitted from the laser light window or a signal is being sent from the remote control unit to the projector. q e KEYSTONE button Corrects keystone distortion. (p25, 42) r AUTO PC button Operates the Auto PC adjustment function.
Part Names and Functions Laser Pointer Function This remote control unit emits a laser beam from the laser light window. With the LASER button pressed, laser light goes on. The signal emission indicator lights red and laser is emitted with red light. With the LASER button pressed for more than 1 minute or released, the light goes off. The laser emitted is a class II laser. Do not look into the laser light window or shine the laser beam on yourself or other people.
Part Names and Functions Part Names and Functions Wireless Mouse Operation The remote control unit can be used as a wireless mouse for your computer. Before operating the wireless mouse, connect your computer and the projector with the supplied USB cable. (See page 17 for connection.) When the Pointer function is used, the wireless mouse is not available. PRESENTATION POINTER button Move the pointer on the screen with this button.
Part Names and Functions Remote Control Code This projector has eight different remote control codes (Code 1-Code 8). Switching remote control codes prevents remote control interference when operating several projectors or video equipment at the same time. Change the remote control code for the projector first before changing that for the remote control unit. See “Remote control” in Setting on page 46. 1 With holding down the MENU button, press the IMAGE button.
Installation Positioning the Projector This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3’(7.7m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen. A:B = 9:1 25.3' (7.7m) (Inch Diagonal) 300” 16.1' (4.9m) Max. Zoom 12.5' (3.8m) 190” 8.2' (2.5m) 150” 100” A Min. Zoom 122” Installation 3.3' (1.
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied.
Installation Connecting to a Computer Cables used for connection • VGA Cable (HDB 15 pin) ✽ • DVI-VGA Cable (HDB 15 pin) • USB Cable • Audio Cables (Mini Plug: stereo) ✽ (✽ = Not supplied with this projector.
Installation Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) ✽ • S-VIDEO Cable ✽ • Audio Cables (Mini Plug: stereo) ✽ (✽ = Not supplied with this projector.
Installation Connecting to Component Video Equipment Cables used for connection • Audio Cables (Mini Plug (stereo) x 2 or RCA x 2)❉, (RCA x 3) ✽ • Scart-VGA Cable ✽ • Component-VGA Cable ✽ (Separately supplied as LV-CA32) (✽ = Not supplied with this projector.
Basic Operation Turning On the Projector 1 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. 2 Connect the projector's AC power cord into an AC outlet. The POWER indicator blinks red in a moment and lights red. 3 Press the POWER button on the top control or on the remote control unit. The POWER indicator turns green lighting and the cooling fans start to operate. The preparation display appears on the screen and the count down starts.
Basic Operation Turning Off the Projector 1 Press the POWER button on the top control or on the remote control unit, and a message "Power off?" appears on the screen. 2 Press the POWER button again to turn off the projector. The POWER indicator starts to blink red, and it continues while the cooling fans are operating for about 90 seconds. (About 120 seconds when the fan mode is L2. See page 48.) The message disappears after 4 seconds.
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedure. Menu icon On-Screen Menu 1 Press the MENU button to display the On-Screen Menu. 2 Press the Point 7 8 buttons to select a Menu icon to adjust. Press the Point ed buttons to select an item to adjust. Pointer (red frame) Press the Point d button to move the pointer. 3 Press the SET button to show the item data.
Basic Operation Menu Bar For computer source Guide Window PC System Menu Image Select Menu Screen Menu Setting Menu Shows the selected Menu of the OnScreen Menu. Used to select computer system. (p28) Used to select an image level among Standard, High contrast, Blackboard(Green), and Custom. (p32) Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (p34) Used to change settings of the projector or reset lamp replace counter.
Basic Operation Zoom and Focus Adjustment Rotate the Zoom Lever to zoom in and out. Rotate the Focus Ring to adjust the projected picture focus. Zoom Lever Focus Ring Auto Setup Function Auto setup function is provided to automatically correct Keystone distortion according to the projector's tilt and adjust the computer display parameters (Fine sync, Total dots and Picture position) by just pressing the AUTO SET button on the top control or on the remote control unit.
Basic Operation Keystone Adjustment If a projected picture still has keystone distortion after pressing the AUTO SET button on the top control or on the remote control unit, correct the image manually as follows: 1 Press the KEYSTONE button on the remote control unit or select Keystone in the Setting Menu (p42). The keystone dialog box appears. 2 Correct keystone distortion by pressing the Point ed78 button. Keystone adjustment can be memorized. (p42) Reduce the upper width with Point e button.
Basic Operation P-Timer Function Press the P-TIMER button on the remote control unit. The timer display “00 : 00” appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop the P-Timer, press the P-TIMER button. And then, press the P-TIMER button again to cancel the P-Timer function. Sound Adjustment Direct Operation indicates approximate level of volume. Volume Press the VOL (+/–) button on the top control or on the remote control unit to adjust volume.
Computer Input Input Source Selection Direct Operation Choose either Computer 1 or Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control unit. Before using these buttons, correct input source should be selected through menu operation as described below. INPUT button Computer 1 Computer 2 ✳ Video COMPUTER button Computer 1 Computer 2 ✳ ✳ See Note on the bottom of this page.
Computer Input Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is shown on page 59 ) ✔Note: The projector may display one of the following messages.
Computer Input Auto PC Adjustment Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adj. 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 button to move the red frame pointer to PC Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to Auto PC Adj. icon and then press the SET button twice.
Computer Input Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button and the On-Screen Menu will appear.
Computer Input Display area Select the resolution at the Display area dialog box. Press the SET button at the Display area icon and the Display area dialog box appears. Display area H Adjusts the horizontal area displayed by this projector. Press the Point 7 8 button to decrease/increase value and then press the SET button. Display area Display area V Adjusts the vertical area displayed by this projector. Press the Point 7 8 button to decrease/increase value and then press the SET button.
Computer Input Image Level Selection Direct Operation Select an image level among Standard, High contrast, Blackboard(Green), Custom by pressing the IMAGE button on the remote control unit. Standard Normal picture level preset on this projector. IMAGE button Standard High contrast Blackboard(Green) High contrast Picture adjustment improved in reproduction of the halftones. This adjustment is suitable for providing a better image in a brighter place.
Computer Input Image Level Adjustment 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust, and then press the SET button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 button.
Computer Input Screen Size Adjustment This projector has a picture screen resize function, which enables you to display the desirable image size. 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the Screen Menu icon. 2 Press the Point d button and move the red frame pointer to the function that you want to select and then press the SET button.
Video Input Input Source Selection (Video, S-Video) INPUT button Direct Operation Video Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control unit. Before using these buttons, correct input source should be selected through menu operation as described below. Computer 1 Computer 2 ✳ VIDEO button Video ✳ See Note on the bottom of this page. Input Menu icon Menu Operation 1 2 3 Input Menu Press the MENU button and the On-Screen Menu will appear.
Video Input Input Source Selection (Component, RGB Scart 21-Pin) Direct Operation INPUT button Computer 1 Choose Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control unit. Before using these buttons, correct input source should be selected through menu operation as described below. Computer 2 ✳ Video COMPUTER button Computer 1 Computer 2 ✳ ✳ See Note on the bottom of this page.
Video Input Video System Selection 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the AV System Menu icon. 2 Press the Point d button to move the red arrow pointer to the system that you want to select and then press the SET button. Video or S-Video Auto The projector automatically detects incoming video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually.
Video Input Image Level Selection Direct Operation IMAGE button Select a desired image level among Standard, Cinema, Blackboard (Green), Custom by pressing the IMAGE button on the remote control unit. Standard Cinema Standard Normal picture level preset on this projector. Blackboard(Green) Cinema Picture level adjusted for the picture with fine tone. Custom Blackboard(Green) Picture level suitable for the image projected on a blackboard.
Video Input Image Level Adjustment 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust and then press the SET button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 button.
Video Input Progressive Interlaced video signal can be displayed in a progressive picture. Off . . . .Not activated. L1 . . . . .Select “L1” for an active picture. L2 . . . . .Select “L2” for a still picture. “OK?” message Move the pointer to [Yes] and then press the SET button. Film This function is effective on 3:2 pulldown video sources. With this function On, the projector reproduces pictures faithful to the original film quality. Reset Resets all adjustment to their previous figure.
Video Input Screen Size Adjustment This projector has a picture screen resize function, which enables you to display the desirable image size. 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the Screen Menu icon. 2 Press the Point d button and move the red frame pointer to the function that you want to select and then press the SET button. Screen Menu Screen Menu icon Move the red frame to a function and press the SET button.
Setting Setting This projector has Setting menu that allows you to set up the other various functions described as follows; 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 button to move the red frame pointer to the Setting Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to set and then press the SET button. The Setting dialog box appears. Setting Menu (Language) Set the red frame pointer to the item and press the SET button.
Setting Blue back Setting When this function is “On,” the projector produces a blue image while input signal is not detected. Display This function decides whether to display On-Screen Displays. On . . . . . . . shows all the On-Screen Displays. Off . . . . . . .
Setting Logo This function decides what to be displayed on the starting-up display as follows: User . . . . . .the image you captured Default . . . .the factory-set logo Off . . . . . . .count-down only Capture Capture This function enables you to capture the image being projected and use it for a starting-up display or interval of presentations. After capturing the projected image, go to the Logo function and set it to “User”.
Setting Standby mode Standby mode Setting This function is available when using Multi Card Imager optionally supplied, and it reduces standby energy when selecting Eco. Eco ···· reduces standby energy. Normal ···· consumes normal standby energy. Power management For reducing power consumption as well as maintaining the lamp life, the Power Management function turns off the projection lamp when the input signal is interrupted and no button is pressed for 30 seconds or more.
Setting Pointer Pointer You can emphasize a part of the projected image with this function. Choose either Spotlight or Pointer with the Point ed button and press the SET button. Then select one of three different sizes (Large, Middle, and Small) of Spotlight or a pointer of three different patterns (Arrow, Finger, and Dot) of Pointer. (See page 12 for operation.) Select Spotlight or Pointer with the Point ed button and press the SET button. Then select size or pattern with the Point 7 8 button.
Setting PIN code lock PIN code lock Setting This function prevents the projector from being operated by an unauthorized person and provides the following settings for security options. Off ...............the projector is unlocked with the PIN code. On1 .............requires to enter the PIN code every time turning on the projector. On2...........
Setting Fan Fan This function provides you the following alternatives in the cooling fans operation after turning off the projector. (p21) L1 . . . . . . . .normal operation. Cooling the projector for 90 seconds after turning off the projector. L2 . . . . . .slower operation than the normal (L1) , but takes longer to cool down the projector. Cooling the projector for 120 seconds after turning off the projector. Lamp counter reset This function is used to reset the lamp replace counter.
Maintenance and Cleaning Warning Indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. TOP CONTROL When the temperature inside the projector exceeds the normal temperature, the projector is automatically shut down to protect the inside of the projector.
Maintenance and Cleaning Cleaning the Air Filters Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat build up and adversely affect the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet.
Maintenance and Cleaning Cleaning the Projection Lens Follow these steps to clean the projection lens. Disconnect the AC power cord before cleaning. 2 Softly wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use lens cleaning paper or a commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface.
Maintenance and Cleaning Lamp Replacement When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the lamp with a new one promptly. Top Control This indicator lights yellow when the life of the projection lamp draws to an end. CAUTION AUTO SET T VOL + LAMP REPLACE CAUTION Allow a projector to cool, for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot.
Maintenance and Cleaning Lamp Replace Counter Be sure to reset the lamp replace counter after the lamp is replaced. When the lamp replace counter is reset, the LAMP REPLACE indicator stops lighting. Turn the projector on, press the MENU button and the OnScreen Menu will appear. Press the Point 7 8 button to move the red frame pointer to the Setting Menu icon. 2 Press the Point d button to move the red frame pointer to the Lamp counter reset item and then press the SET button.
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described in "Connecting to a Computer" and “Connecting to Video Equipment” on page17-19. – Make sure all equipment is connected to AC outlet and the power is turned on. – When you operate the projector with a computer and it does not project an image, restart the computer.
Appendix Some displays are not seen during the Operation. – Check the Display item. (See “Setting” on page 43.) PIN code dialog box appears at start-up. – PIN code lock is being set. Input a PIN code (1234 or numbers you have set). (See “PIN code lock” on page 20 and 47.) Computer 2 cannot be selected. – Select Computer 2 at the Terminal item in the Setting Menu. (See “Setting” on page 44.) The Terminal item cannot be selected.
Appendix Menu Tree Computer Input / Video Input Input Computer 1 Computer 2 Video Sound RGB( Analog ) Go to System (1) RGB( PC Digital ) N/A RGB( AV HDCP ) N/A RGB Go to System (1) Component Go to System (2) RGB( Scart ) N/A Auto Go to System (3) Video Go to System (3) S-Video Go to System (3) ✽N/A - - - not applicable Sound Volume Mute Quit 0 - 63 On / Off Computer Input System (1) Image Select MODE 1 MODE 2 SVGA 1 ---- Standard High contrast Blackboard(Green) Custom ✽Systems
Appendix Setting Video Input System (2) Auto 1080i 1035i 720p 575p 480p 575i 480i System (3) Auto PAL SECAM NTSC NTSC 4.
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER WARNING LAMP REPLACE red/green red yellow Projector Condition The projector is OFF. (The AC power cord is unplugged.) • • • lights green. ✽ When ✽ The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. ✽ The projector is ready to be turned on with the POWER button.
Appendix Compatible Computer Specifications LV-7225 / LV-7220 can basically accept the signal from all computers with the V, H-Frequency mentioned below and less than 140 MHz of Dot Clock. LV-5220 can basically accept the signal from all computers with the V, H-Frequency mentioned below and less than 100 MHz of Dot Clock. These modes are not available on LV-5220.
Appendix Technical Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Panel Resolution LCD Panel System Panel Resolution Number of Pixels Signal Compatibility Color System High Definition TV Signal Scanning Frequency Multi-media Projector 11.81" x 3.23" x 8.94" (300mm x 82mm x 227mm) (Not including adjustable feet) 6.48 lbs (2.9kgs) 0˚ to 11.9˚ LV-7225 / LV-7220 LV-5220 0.
Appendix Accessories Owner's Manual AC Power Cord Remote Control Unit and Batteries DVI-VGA Cable USB Cable Lens Cover with String and Screw Soft Carrying Bag PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
Appendix Configurations of Terminals RGB INPUT/COMPONENT INPUT/RGB OUTPUT TERMINAL (ANALOG) Terminal : HDB15-PIN 4 5 10 15 14 2 3 9 8 13 1 7 12 6 11 1 2 3 4 5 6 7 8 Red (R/Cr) Input / Output Green (G/Y) Input / Output Blue (B/Cb) Input / Output ----Ground (Horiz.sync.) Ground (Red) Ground (Green) Ground (Blue) C1 C2 C3 C4 C5 Analog Red Input Analog Green Input Analog Blue Input Analog Horiz. sync Analog Ground (R/G/B) 1 2 3 4 5 6 7 8 T.M.D.S. Data2– T.M.D.S. Data2+ T.M.D.S.
Appendix While the projector is locked with the PIN code... Put the label below (supplied) on in a prominent place of the projector's body while it is locked with a PIN code.
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. CANON CANADA, INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7 Canada CANON LATIN AMERICA, INC. 703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A. CANON EUROPA N.V. P.O.Box 2262, 1180 EG Amstelveen, The Netherlands CANON COMMUNICATION & IMAGE FRANCE S.A. 102, Avenue du General de Gaulle, 92250 La Garenne Colombes, France CANON (UK) LTD.