LV7555_Expand_command_specification

ManualsBrandsCanon ManualsProjectorLV-7555

MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION

Software Engineer Division

LV-7555 (For MR3P series)

Expand Serial Command Specification

Page 1/53

Summary of content (53 pages)

PAGE 1
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division LV-7555 (For MR3P series) Expand Serial Command Specification Page 1/53
PAGE 2
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division -CONTENT1. OVERVIEW 2. Serial Interface Specification 2.1 Communication Specification 2.2 Connection 3. Note for Communications 4. Name Definition 5. Functional Execution Command Table 5.1 Image Series Command Table 5.2 PC Control Series Command Table 5.3 Input Control Series Command Table 5.4 Screen Series Command Table 5.5 Lam Series Command Table 5.6 Sound Series Command Table 5.7 Setting Series Command Table 5.
PAGE 3
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.4.6 CF_GAMMA COMMAND 8.4.7 CF_WBAL-COMMAND 8.4.8 CF_COLTEMP COMMAND 8.4.9 CF_NZRED COMMAND 8.4.10 CF_PROGV COMMAND 8.4.11 CF_IMAGE COMMAND 8.4.12 CF_IMAGEADJ COMMAND 8.4.13 CF_APCTRL COMMAND 8.4.14 CF_COLOMNSAV COMMAND 8.4.15 CF_COLMNLD COMAND 8.4.16 CF_TURBO COMMAND 8.5 PC Control Series Command 8.5.1 CF_FSYNC COMMAND 8.5.2 CF_TDOTS COMMAND 8.5.3 CF_CLAMP COMMAND 8.5.4 CF_H-POS COMMAND 8.5.
PAGE 4
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.7.8 CF_VSCALE COMMAND 8.7.9 CF_VPOS COMMAND 8.7.10 CF_HSCALE COMMAND 8.7.11 CF_HPOS COMMAND 8.8 Lamp Series Command 8.8.1 CF_LAMPH COMMAND 8.8.2 CF_LAMPMODE COMMAND 8.9 Sound Series Command 8.9.1 CF_VOLUME COMMAND 8.9.2 CF_MUTE COMMAND 8.9.3 CF_BLTINSP COMMAND 8.10 Setting Series Command 8.10.1 CF_VOLUME COMMAND 8.10.2 CF_DISP COMMAND 8.10.3 CF_LOGO COMMAND 8.10.4 CF_CF_CEIL COMMAND 8.10.
PAGE 5
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.4.9 CR_WBAL-B COMMAND 9.4.10 CR_COLTEMP COMMAND 9.4.11 CR_NZRED COMMAND 9.4.12 CR_PROGV COMMAND 9.4.13 CR_IMAGE COMMAND 9.4.14 CR_IMGGMD COMMAND 9.4.15 CR_APCTRL COMMAND 9.4.16 CR_TURBO COMMAND 9.5 Status Read Command 9.5.1 CR_FSYNC COMMAND 9.5.2 CR_TDOTS COMMAND 9.5.3 CR_CLAMP COMMAND 9.5.4 CR_H-POS COMMAND 9.5.5 CR_V-POS COMMAND 9.5.6 CR_DDOTS COMMAND 9.5.7 CR_DLINE COMMAND 9.5.
PAGE 6
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.9 Status Read Command for LAMP 9.9.1 CR_LAMPREPL COMMAND 9.9.2 CR_LAMPMODE COMMAND 9.9.3 CR_PROJH COMMAND 9.10 Sound Series Status read Command 9.10.1 CR_VOLUME COMMAND 9.10.2 CR_MUTE COMMAND 9.10.3 CR_BLTINSP COMMAND 9.11 Status Read Command for Setting 9.11.1 CR_BBACK COMMAND 9.11.2 CR_DISP COMMAND 9.11.3 CR_LOGO COMMAND 9.11.4 CR_RCODE COMMAND 9.11.5 CR_LANG COMMAND 9.11.6 CR_P-MANE COMMAND 9.
PAGE 7
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 1. OVERVIEW 1.1 This Functional Specification defines the Network Card and the communication functions for MR3P Series (1.3”XGA Ⅴ-4 LV-7555). 1.2 A projector firmware Ver. 1.x -ready 1.3 Commands are to communicate to Network card, but most commands control a remote projector with PC installed RS232C. That’s why Commands are defined as expand serial commands. 2. Serial Interface Specification 2.
PAGE 8
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 3. Note for Communications 3.1 The expand Command is defined one Command/one line that starts “C” and ends carriage return (0x0D). 3.2 When a projector receives carriage return (0x0D), it starts decoding. 3.3 There are two type of expand serial. Command and functional execution Commands and Status Read Command. Functional Execution COMMAND Ex.”CF_BRIGHT_032”[CR] Note) _means a space Status Read Command Ex.”CR_RIGHT”[CR] 3.
PAGE 9
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division The projector usuall issues a return commands in 1000 ms after receiving a return command. It takes more than 1000ms for some functional execution commands (CF) to send a return command as shown in the table below. COMMAND 3.4.
PAGE 10
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 5. Functional Execution Command Table 5.
PAGE 11
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 5.4 Screen Series Command Table Execute Command CF_SCREEN_%1 [CR] CF_FLSCREN_%1 [CR] CF_TRUE_%1 [CR] CF_DZCENT_%1 [CR] CF_KEYSTONE_%1 [CR] CF_KYSTNMODE_%1 [CR] CF_ANAMORPHIC_%1 [CR] CF_VSCALE_%1 [CR] CF_VPOS_%1 [CR] CF_HSCALE_%1 [CR] CF_HPOS_%1 [CR] Item Select Screen size. Set or cancel for Full Screen. Set or cancel for Screen True. Cancel digital zoom. Set Keystone. Set Keystone store mode.
PAGE 12
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 6. Status Read Command Table 6.
PAGE 13
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 6.
PAGE 14
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 6.10 Network Viewer Series Status Read Command Table Status Read Command CR_NETFUNC [CR] Item Get COMMAND about Network Manager 7. Error Code Table Error Code ？ Content -When receives data that cannot be decoded -Parameter determination error(digit number error, and incorrect letter included) Normal Reception (not error) The function is not available in the selected mode.
PAGE 15
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.3 Operating Condition When the projector is in the following state, function execute Command will be limited. The functional execution Command is limited under the following state. State Read Commands are available under the following state.
PAGE 16
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.4.3 CF_COLOR COMMAND COMMAND %1 Details Response 8.4.4 “000-063”------ Directly select for color setting value “UP”---------------- Color setting value +1 “DN”---------------- Color setting value -1 Set the user control color value. The value set by this Command will not be saved to the projector. Therefore, when ALL OFF the projector, the value will return to the original setting.
PAGE 17
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.4.6 CF_GAMMA COMMAND COMMAND %1 Details Response 8.4.7 “000-015”------ Directly select for Gamma setting value “UP”---------------- Current setting value +1 “DN”---------------- Current setting value-1 Set the User Control Gamma Value. The value set by this Command will not be saved to the projector. Therefore, when ALL OFF the projector, the value will return to the original setting.
PAGE 18
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.4.9 CF_NZRED COMMAND COMMAND %1 Details Response “CF_NZRED_%1”[CR] “ON”------ Select Noise Reduction “OFF”---- Cancel Noise Reduction Set/Cancel Noise Reduction.(When it is in usual Power ON state, this is valid.) The value set by this Command will not be saved to the projector. Therefore, when ALL OFF the projector, the value will return to the original setting. (For Stand-by mode, this value stays.
PAGE 19
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.4.12 CF_IMAGEADJ COMMAND COMMAND %1 Details Response “CF_IMAGEADJ_%1”[CR] “RST”------Reset Image adjustment “STR1”----Store current image adjustment to Custom Reset and store for image adjustment. (When it is in usual Power ON state, this is valid.) “STR1” execute image adjustment on OSD menu. The value set by this Command will be stored.
PAGE 20
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.4.16 CF_TURBO COMMAND COMMAND %1 Details Response “CF_TURBO_%1”[CR] “ON”---- Set Bright SW to ON. “OFF”-- Set Bright SW to OFF. Set Bright SW to the status by %1specification (Only valid when it is in the usual Power On state.) Acceptable “000”[CR] Unacceptable “Error Code”[CR] 8.5 PC Control Series COMMAND 8.5.1 CF_FSYNC COMMAND COMMAND %1 Details Response 8.5.
PAGE 21
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.5.3 CF_CLAMP COMMAND COMMAND %1 Details Response 8.5.4 “CF_CLAMP_%1”[CR] “0000-0127”---- Directly set Clamp setting value. “UP”------------------ Clamp setting value+1 “DN”------------------ Clamp setting value-1 Set Clamp of PC signal.(Only valid when it is in the usual Power On state.) The value set by this Command will not be saved to the projector..
PAGE 22
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.5.5 CF_V-POS COMMAND COMMAND “CF_V-POS_%1”[CR] “0000-nnnn”-- Directly set Vertical Position “nnnn” means maximum value. This value is from current Total Line value – display Line value. %1 “UP”---------------- Vertical Position setting value +1. “DN”---------------- Vertical Position setting value-1. Details Response 8.5.6 Set vertical position of PC signal. Only valid when it is in the usual Power On state.
PAGE 23
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.5.7 CF_DLINE COMMAND COMMAND “CF_DLINE_%1”[CR] “0100-nnnn”-- directly specify Display Line value “nnnn” means maximum. This value is from current Total Line value – Vertical Position value. %1 “UP”---------------- Display Line +1 “DN”---------------- Display Line -1 Details Response 8.5.8 Set Display Line of PC signal (Only valid when it is in the usual Power On state.
PAGE 24
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.5.9 CF_ORGMODE COMMAND COMMAND %1 Details Response “CF_ORGMODE_%1”[CR] “XGA1”,”HDTV1080”...Etc After EXTn is set by PC Control Series Command and CF_SETPCADJ COMMAND such as CF_FSYNC / CF_TDOTS, this command select original signal. Acceptable “000”[CR] Unacceptable “101”[CR] ---- When Input is Video Series 8.5.
PAGE 25
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.6.2 CF_SOURCE COMMAND COMMAND “CF_SOURCE_%1”[CR] When Input is 1 %1 Details Response 8.6.
PAGE 26
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.6.5 CF_INPUT3 COMMAND COMMAND %1 Details Response 8.6.6 “VIDEO”-------- Select Composite Video Input “S-VIDEO”---- Select S-Video input “YPBPR”-------- Select Y/Pb/Pr Select Input-3 and specified source by %1. (Only valid when it is in the usual Power On state.) Acceptable “000”[CR] Unacceptable “%%%”[CR] CF_INPUT4 COMMAND COMMAND %1 Details Response 8.6.
PAGE 27
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division available only when Input is Y, Pb/Cb, Pr/Cr. Response Acceptable “000”[CR] Unacceptable “Error Code”[CR] 8.7 Screen Control Series COMMAND 8.7.1 CF_SCREEN COMMAND COMMAND “CF_SCREEN_%1”[CR] Input is computer %1 Input is Video Series Details Response 8.7.
PAGE 28
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.7.3 CF_TRUE COMMAND COMMAND %1 Details Response 8.7.4 “ON”------ Select True “OFF”---- Cancel True Set/cancel True Only valid when it is in the usual Power On state and input is computer. Acceptable “000”[CR] Unacceptable “101”[CR] ---- When Input is Video Series CF_DZCENT COMMAND COMMAND %1 Details Response 8.7.
PAGE 29
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.7.6 CF_KYSTNMODE COMMAND COMMAND %1 Details Response 8.7.7 “STR”------ Set Keystone store mode to Store “RST” ----- Set Keystone store mode to Reset Set Keystone store mode(Only valid when it is in the usual Power On state) Acceptable “000”[CR] Unacceptable “Error Code”[CR] CF_ ANAMORPHIC COMMAND COMMAND %1 Details Response 8.7.
PAGE 30
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.7.9 CF_VPOS COMMAND COMMAND %1 Details Response “CF_VPOS_%1”[CR] “064”--- +64 “063”--- +63 : “002”--- +2 “001”--- +1 “000”--- ±0 “-01”--- -1 “-02”--- -2 : “-63”--- -63 “-64”--- -64 Set V Position. (Only valid when it is in the usual Power On state.) Acceptable “000”[CR] Unacceptable “Error Code”[CR] 8.7.10 CF_HSCALE COMMAND COMMAND %1 Details Response “CF_HSCALE_%1”[CR] The same as CF_VSCALE COMMAND Set H Scale.
PAGE 31
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.8.2 CF_LAMPMODE COMMAND COMMAND %1 Details Response “CF_LAMPMODE_%1”[CR] “NORMAL”-- Set lamp to normal mode “ECO”-------- Set lamp to silent mode. “AUTO”------ Set lamp to auto mode Select lamp mode. (Only valid when it is in the usual Power On state.) The value set is stored in EEPROM. When ALL OFF the projector, the value will return to the original setting. Acceptable “000”[CR] Unacceptable “Error Code”[CR] 8.
PAGE 32
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.9.3 CF_BLTINSP COMMAND COMMAND %1 Details Response “CF_BLTINSP_%1”[CR] “ON”------ Select Built-in Speaker “OFF”---- Cancel Boiling Speaker Set/Cancel Built-in Speaker. (Only valid when it is in the usual Power On state.) Acceptable “000”[CR] Unacceptable “Error Code”[CR] 8.10 Setting Series COMMAND 8.10.
PAGE 33
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.10.4 CF_CEIL COMMAND COMMAND %1 Details Response “CF_CEIL_%1”[CR] “ON”------ Select Ceiling “OFF”---- Cancel Ceiling Set/Cancel Ceiling (Only valid when it is in the usual Power On state.) The value set is stored in EEPROM. When ALL OFF the projector, the value will return to the original setting. Acceptable “000”[CR] Unacceptable “Error Code”[CR] 8.10.
PAGE 34
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.10.7 CF_LANG COMMAND COMMAND %1 Details Response “CF_LANG_%1”[CR] “ENG”---- Select English “DEU”---- Select German “FRA”---- Select French “ITA”---- Select Italy “ESP”---- Select Spanish “POR”---- Select Portuguese “NED”---- Select Dutch “SVE”---- Select Swedish “JPN”---- Select Japanese “CHI”---- Select Chinese “KOR”---- Select Korean “RUS”---- Select Russian Set OSD language.
PAGE 35
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 8.10.10 CF_P-MANETIME COMMAND COMMAND “01”-”30”-- Directly set the time by the minute “UP”------------ Set the time 1 minute longer “DN”------------ Set the time 1 minute shorter %1 Set Power management time. (Only valid when it is in the usual Power On state.) The value set is stored in EEPROM. When ALL OFF the projector, the value will return to the original setting. Details Response 8.10.
PAGE 36
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9 Status Read Command 9.1 Format 1. PC issues Commands as below. “CR_ COMMAND”[CR] COMMAND:character line 2. When projector receives the appropriate Command, it returns a character line as the required data. “000_”%1 [CR] %1:Required Data(character line) 3. When receiving data cannot be decode, the projector returns”？”［CR］ 9.
PAGE 37
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.4.3 CR_COLOR COMMAND COMMAND Details “CR_COLOR”[CR] Get Color value of user control Acceptable Response %1 “000”-”063” Unacceptable 9.4.
PAGE 38
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.4.8 CR_WBAL-G COMMAND Details COMMAND “CR_WBAL-G”[CR] Get White Balance Green of user control Acceptable Response %1 “000”-”063” Unacceptable 9.4.9 CR_WBAL-B COMMAND Details “？”[CR] COMMAND “CR_WBAL-B”[CR] Get White Balance Blue of user control Acceptable Response “000_%1”[CR] %1 Unacceptable “000_%1”[CR] “000”-”063” “？”[CR] 9.4.
PAGE 39
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.4.12 CR_PROGV COMMAND COMMAND Details “CR_PROGV”[CR] Get Progressive setting status. Acceptable Response %1 Unacceptable “000_%1”[CR] “L1”----- Progressive Mode L1 setting “L2”----- Progressive Mode L2settiing “OFF”--- Progressive cancellation “？”[CR] 9.4.
PAGE 40
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.4.16 CR_TURBO COMMAND COMMAND Details “CR_TURBO”[CR] Get Bright SW setting status Acceptable Response %1 Unacceptable “000_%1”[CR] “ON”---- Bright SW is ON “OFF”-- Bright SW is OFF “？”[CR] 9.5 STATUS READ COMMAND FOR PC 9.5.1 CR_FSYNC COMMAND COMMAND Details “CR_FSYNC”[CR] Get Fine Sync value Acceptable Response %1 Unacceptable 9.5.
PAGE 41
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.5.4 CR_H-POS COMMAND COMMAND Details “CR_H-POS”[CR] Get Horizontal position value Acceptable Response %1 Unacceptable 9.5.5 Details “Error Code”[CR] --- Invalid “？”[CR] ------------- When receives unclear Command “CR_V-POS”[CR] Get Vertical position value.
PAGE 42
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.5.8 CR_ORGMODE COMMAND COMMAND Details “CR_ORGMODE”[CR] Get signal for MODE in PC Adjust When MODE1-MODE5 or EXT6-EXT60 are not selected, get current signal. Acceptable Response %1 Unacceptable 9.5.9 “000_%1”[CR] “XGA1” “HDTV1080”...Etc “？”[CR] CR_PCSTORE COMMAND COMMAND Details Response “CR_PCSTORE”[CR] Get the status if MODE1-MODE5 is Free or Stored for PC Adjust.
PAGE 43
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.6 STATUS READ COMMAND FOR VIDEO 9.6.1 CR_SERSYS COMMAND COMMAND Details “CR_SERSYS”[CR] Select selected signal. When Auto mode, it returns by auto-detect. Only available when Input is video. (Unavailable when Input is computer.
PAGE 44
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.7.3 CR_SRCINP1COMMAND COMMAND Details Response 9.7.4 “CR_SRCINP1”[CR] Get INPUT 1 Source.
PAGE 45
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.7.7 CR_SYSTEM COMMAND COMMAND Details “CR_SYSTEM”[CR] Get selected System Acceptable Response “000_%1”[CR] When Input is PC Series “MODE1” “MODE2” “MODE3” “MODE4” “MODE5” When Input is video series “AUTO” ------- Auto is selected. “NTSC” ------- NTSC is selected. “NTSC443”-- NTSC4.43 is selected. “PAL” --------- PAL is selected. “SECAM” ----- SECAM is selected. “PAL-M” ----- PAL-M is selected.
PAGE 46
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.8.3 CR_ KYSTNMODE COMMAND COMMAND Details “CR_KYSTONMODE”[CR] Get Keystone Store Mode setting status Acceptable Response %1 “000_%1”[CR] “STR”-- “Store Mode” is Store “RST”-- “Store Mode” is Reset “？”[CR] Unacceptable 9.8.
PAGE 47
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.8.8 CR_HPOS COMMAND COMMAND Details “CR_HPOS”[CR] Get H Position setting status Acceptable Response “000_%1”[CR] %1 “-64”-”064” Unacceptable “？”[CR] 9.9 STATUS READ COMMAND FOR LAMP 9.9.1 CR_LAMPREPL COMMAND COMMAND Details “CR_LAMPREPL”[CR] Get lamp replacement time information Acceptable Response %1 Unacceptable 9.9.
PAGE 48
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.10 Sound Series Status Read COMMAND 9.10.1 CR_VOLUME COMMAND COMMAND Details “CR_VOLUME”[CR] Get user control Volume Acceptable Response %1 Unacceptable “000_%1”[CR] “000”-”063” “？”[CR] 9.10.2 CR_MUTE COMMAND COMMAND Details “CR_MUTE”[CR] Get sound mute setting value Acceptable Response %1 Unacceptable “000_%1”[CR] “ON”---- Sound mute is ON “OFF”-- Sound mute is OFF “？”[CR] 9.10.
PAGE 49
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.11.2 CR_DISP COMMAND COMMAND Details “CR_DISP”[CR] Get Display setting status Acceptable Response %1 Unacceptable “000_%1”[CR] “ON”----- Set Display “OFF”--- Cancel Display “？”[CR] 9.11.3 CR_LOGO COMMAND COMMAND Details “CR_LOGO”[CR] Get Logo setting status Acceptable Response %1 Unacceptable “000_%1”[CR] “ON”----- Set Logo “OFF”--- Cancel Logo “？”[CR] 9.11.
PAGE 50
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.11.6 CR_ON-STA COMMAND COMMAND Details “CR_ON-STA”[CR] Get Power ON Start setting status Acceptable Response %1 Unacceptable “000_%1”[CR] “ON”＝Set Power ON Start “OFF”＝Cancel Power ON Start “？”[CR] 9.11.
PAGE 51
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.11.10 CR_KEYDIS COMMAND COMMAND Details “CR_KEYDIS”[CR] Get RC/KEY status Acceptable Response %1 Unacceptable “000_%1”[CR] “N/A”＝Both RC & KEY are available. “RC” ＝RC is locked “KEY” ＝KEY is locked “？”[CR] 9.12 Other Status Read COMMAND 9.12.
PAGE 52
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.12.4 CR_PTIMER COMMAND COMMAND Details “CR_PTIMER”[CR] Get Presentation Timer status Acceptable Response %1 Unacceptable “000_%1”[CR] “ON”------- Presentation timer is active “STOP”--- Presentation timer is pause “OFF”----- Presentation timer is inactive “？”[CR] 9.12.5 CR_INFPFAIL COMMAND COMMAND Details “CR_INFPFAIL”[CR] Get the power failure status.
PAGE 53
MR3P Series EXPAND SERIAL COMMAND FUNCTION SPECIFICATION Software Engineer Division 9.12.7 CR_TEMPFAIL COMMAND COMMAND Details “CR_TEMPFAIL”[CR] Get the temperature inside a projector. When some temperature sensors are installed in the projector, it is possible to know the temperature all at once. Acceptable “000_%1_%2_%3”[CR] %1＝Temperature, sensor 1 %2＝Temperature, sensor 2 %3＝Temperature, sensor 3 Response %1 %2 %3 Unacceptable (Ex.) “_31.5Ｆ”[CR] _means a space.