Multimedia Projector LV-S4 Owner’s Manual E English
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. ◆ Compact Design ◆ This projector is designed compact in size and weight. It is easy to carry and work anywhere you wish to use.
Table of Contents Features and Design . . . . . . . . . . . . . . . . . . .2 Table of Contents . . . . . . . . . . . . . . . . . . . . . .3 To the Owner . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety Instructions . . . . . . . . . . . . . . . . . . . .5 Computer Input . . . . . . . . . . . . . . . . . . . . .
To the Owner Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. This projector should be operated only from the type of power source indicated on the marking label.
Safety Instructions Air Circulation Installing the Projector in Proper Position Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. 20˚ Do not tilt the projector more than 20 degrees above and below. CAUTION Hot air is exhausted from the exhaust vent.
Compliance Federal Communication Commission Notice Multimedia Projector, Model : LV-S4E and LV-S4U This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Part Names and Functions q Focus Ring w Infrared Remote Receiver e Projection Lens r Zoom Lever t Lens Cover y Air Intake Vent u Exhaust Vent Front q w i e Hot air is exhausted from the exhaust vent. Do not put heat-sensitive objects near this side. r t CAUTION u i Speaker y Back t q Air Intake Vent w Terminals and Connectors e Power Cord Connector r Exhaust Vent t Top Controls and Indicators CAUTION q Hot air is exhausted from the exhaust vent.
Part Names and Functions RESET q w VIDEO AUDIO IN COMPUTER/ S-VIDEO/ COMPONENT IN y q VIDEO Connect the composite video output from video equipment to VIDEO jack. (p16) w AUDIO IN (Stereo) Connect the audio output from computer or video equipment connected to q or y to this jack. (p15, 16) e AUDIO OUT(VARIABLE) Connect an external audio amplifier to this jack. (p15, 16) This terminal outputs sound from AUDIO IN terminal.
Part Names and Functions Top Control POWER VOL + VOL - MENU INPUT WARNING LAMP REPLACE q w e r q POWER button Turn the projector on or off. (p17, 18) POWER indicator Flash red until the projector gets ready to be turned on. It turns red when the projector is in the stand-by mode. It remains green while the projector is under operation. (p17, 18, 54) w LAMP REPLACE indicator Turn yellow when the life of the projection lamp draws to an end.
Part Names and Functions Part Names and Functions Remote Control Unit q POWER button Turn the projector on or off. (p17, 18) w VIDEO button Select the VIDEO input. (p32) e w e COMPUTER button Select the COMPUTER input source. (p24, 32) q r MENU button Open or close the On-Screen Menu. (p20) t KEYSTONE button Correct the keystone distortion. (p22, 38) y D.ZOOM ed buttons Select the Digital zoom +/– mode and resize the image.
Part Names and Functions Remote Control Unit Battery Installation 1 Remove the battery compartment lid. 2 Slide the batteries into the compartment. 3 Replace the compartment lid. Two AAA size batteries For correct polarity (+ and –), be sure battery terminals are in contact with pins in the compartment. To insure safe operation, please observe the following precautions : ● Use (2) AAA, SUM-4 or LR03 type alkaline batteries. ● Replace two batteries at the same time.
Installation Positioning the Projector This projector is designed to project on a flat projection surface and can be focused from 4.3’(1.3m) - 21.3’(6.5m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen. A:B = 9:1 21.3' (6.5m) 16.1' (4.9m) (Inch Diagonal) 200” Max. Zoom 10.6' (3.2m) 150” Min. Zoom Installation 4.3' (1.
Installation Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied.
Installation Connecting to a Computer Cables used for connection • VGA Cable (HDB 15 pin) (Only one cable is supplied) • Audio Cable (Mini Plug: stereo) ✽ (✽ = Not supplied with this projector.
Installation Connecting to Video Equipment Cables used for connection • Scart-VGA Cable (Separately supplied as LV-CA31) ✽ • S-VIDEO-VGA Cable (Separately supplied as LV-CA33) ✽ • S-VIDEO Cable ✽ • Component-VGA Cable (Separately supplied as LV-CA32) ✽ • Component Cable ✽ • Video Cable ✽ • Audio Cables (Mini Plug: stereo) ✽ (✽ = Not supplied with this projector.
Basic Operation Turning On the Projector 1 Complete peripheral connections (with a computer, VCR, etc.) before turning on the projector. 2 Connect the projector's AC power cord into the AC outlet. The POWER indicator blinks red in a moment and emits red light. 3 Press the POWER button on the top control or on the remote control unit. The POWER indicator turns green lighting and the cooling fans start to operate. The preparation display appears on the screen and the count down starts.
Basic Operation Turning Off the Projector 1 Press the POWER button on the top control or on the remote control unit, and a message "Power off?" appears on the screen. 2 Press the POWER button again to turn off the projector. The POWER indicator starts to blink red, and it continues while the cooling fans are operating for about 90 seconds. (About 120 seconds when the fan mode is L2. See page 44.) The message disappears after 4 seconds.
Basic Operation Zoom and Focus Adjustment Rotate the Zoom Lever to zoom in and out. Rotate the Focus Ring to adjust the projected picture focus.
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedure. Menu icon On-Screen Menu 1 Press the MENU button to display the On-Screen Menu. 2 Press the Point 7 8 buttons to select a Menu icon to adjust. Press the Point ed buttons to select an item to adjust. Pointer (red frame) Press the Point d button to move the pointer. 3 Press the OK button to show the item data.
Basic Operation Menu Bar For computer source Guide Window Show the selected Menu of the OnScreen Menu. PC System Menu Used to select computer system. (p25) Image Select Menu Screen Menu Setting Menu Used to select an image level among Standard, High contrast, Blackboard(Green), and Custom. (p29) Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (p31) Used to change settings of the projector or reset lamp replace counter.
Basic Operation Keystone Adjustment If a projected picture has keystone distortion, correct the image with the keystone adjustment. 1 Press KEYSTONE button on the remote control unit or select Keystone on the Setting menu (p38) to display the Keystone dialog box. 2 Correct keystone distortion by pressing Point ed buttons. Press Point e button to reduce the upper part of image, and press Point d button to reduce the lower part. Reduce the upper width with Point e button.
Basic Operation INPUT P-Timer Function Press the P-TIMER button on the remote control unit. The timer display “00 : 00” appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop the P-Timer, press the P-TIMER button. Press the PTIMER button again to cancel the P-Timer function. POWER COMPUTER VIDEO MENU VOL- VOL+ Remote Control Unit KEYSTONE IMAGE NO SHOW D.
Computer Input Input Source Selection Direct Operation Select Computer by pressing the INPUT button on the top control or press the COMPUTER button on the remote control unit. Before using these buttons, correct input source should be selected through menu operation as described below.
Computer Input Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional settings. (Signal formats provided in this projector is shown on page 55 ) ✔Note: • The projector may display one of the following messages.
Computer Input Auto PC Adjustment INPUT POWER COMPUTER VIDEO The Auto PC Adj. function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. The Auto PC Adj. function can be operated as follows. MENU Direct Operation The Auto PC adjustment function can be operated directly by pressing the AUTO PC button on the remote control unit. VOL- VOL+ Remote Control Unit KEYSTONE IMAGE NO SHOW D.
Computer Input Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer. PC Adjust Menu icon 1 Press the MENU button and the On-Screen Menu will appear.
Computer Input Display area Press the OK button to display the Display area dialog box. Select the resolution at the Display area dialog box. Press the OK button at the Display area icon and the Display area dialog box appears. Display area H Adjust the horizontal area displayed by this projector. Press the Point 7 8 buttons to decrease/increase the value and then press the OK button. Display area Display area V Adjust the vertical area displayed by this projector.
Computer Input INPUT Image Level Selection Direct Operation POWER COMPUTER VIDEO MENU VOL- VOL+ Remote Control Unit Select an image level among Standard, High contrast, Blackboard(Green), Custom by pressing the IMAGE button on the remote control unit. KEYSTONE IMAGE NO O SHOW IMAGE button Standard Normal picture level preset on this projector. High Contrast Picture adjustment improved in reproduction of the halftones. This adjustment is suitable for providing a better image in a brighter place.
Computer Input Image Level Adjustment 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust, and then press the OK button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Computer Input Screen Size Adjustment This projector has a picture screen resize function, which allows you to customize the image size. 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. 2 Press the Point d button and move the red frame pointer to the function that you want to select and then press the OK button. Screen Menu Screen Menu icon Move the red frame to the function and press the OK button.
Video Input Input Source Selection Direct Operation Select either Video or Computer by pressing the INPUT button on the top control or VIDEO or COMPUTER button on the remote control unit. Before using these buttons, correct input source should be selected through menu operation as described below.
Video Input Video System Selection 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 buttons to move the red frame pointer to the AV System Menu icon. 2 Press the Point d button to move the red arrow pointer to the system that you want to select and then press the OK button. Video or S-Video Auto The projector automatically detects incoming video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually.
Video Input INPUT Image Level Selection POWER COMPUTER VIDEO Direct Operation MENU Select a desired image level among Standard, Cinema, Blackboard (Green), Custom by pressing the IMAGE button on the remote control unit. VOL- VOL+ Remote Control Unit KEYSTONE IMAGE NO SHOW Standard Normal picture level preset on this projector. Cinema Picture level adjusted for the picture with fine tone.
Video Input Image Level Adjustment 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to adjust and then press the OK button. The level of each item is displayed. Adjust each level by pressing the Point 7 8 buttons.
Video Input Progressive Interlaced video signal can be displayed in a progressive picture. Off . . . .Not activated. L1 . . . . .Select “L1” for an active picture. L2 . . . . .Select “L2” for a still picture. Film This function is effective on 3-2 pulldown video sources. With this function on, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the OK button. The confirmation box will appear and then select [Yes].
Video Input Screen Size Adjustment This projector has a picture screen resize function, which allows you to customize the image size. 1 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. 2 Press the Point d button and move the red frame pointer to the function that you want to select and then press the OK button. Screen Menu Screen Menu icon Move the red frame to a function and press the OK button.
Setting Setting Setting menu allows you to set up the other various functions described as follows; 1 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. 2 Press the Point d button to move the red frame pointer to the item that you want to set and then press the OK button. The Setting dialog box appears. Setting Menu (Language) Set the red frame pointer to the item and press the OK button.
Setting Logo PIN code lock Logo PIN code lock Setting This function prevents an unauthorized person from changing the Logo setting. Off . . . . .the Logo setting can be changed freely from the Logo menu. (p40) On . . . . . .the Logo setting cannot be changed without the Logo PIN code. If you want to change the Logo PIN code lock setting, enter a Logo PIN code along the following steps. The initial Logo PIN code is set "4321" at the factory.
Setting Logo This function decides what to be displayed on the starting-up display as follows: User . . . . . .the image you captured Default . . . .the factory-set logo Off . . . . . . .count-down only Capture Capture This function enables you to capture the image being projected and use it for a starting-up display or interval of presentations. After capturing the projected image, go to the Logo function and set it to “User”.
Setting Power management Setting For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the input signal is interrupted and no button is pressed for a certain period. Power management Time left until Lamp off If the input signal is interrupted and no button is pressed for 30 seconds or more, the timer display with the message "No signal" appears on the screen. The count-down of the set time will get started.
Setting INPUT Remote control This projector has two different remote control unit codes; the factory-set normal code (Code 1) and the secondary code (Code 2). This switching function prevents remote control unit interference when operating several projectors or video equipment at the same time. When operating the projector in “Code 2”, both the projector and remote control unit must be switched to “Code 2”.
Setting PIN code lock PIN code lock Setting This function prevents the projector from being operated by an unauthorized person and provides the following settings for security options. Off ...............the projector is not locked with the PIN code. On1 .............require to enter the PIN code every time turning on the projector. ..........
Setting Fan Fan This function provides you the following alternatives in the cooling fans' operation after turning off the projector. (p18) L1 . . . . . . . .normal operation. Cooling the projector for 90 seconds after turning off the projector. L2 . . . . . .slower operation than the normal (L1) , but takes longer to cool down the projector. Cooling the projector for 120 seconds after turning off the projector. Lamp counter reset This function is used to reset the lamp replace counter.
Maintenance and Cleaning Warning Indicator The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING indicator is blinking red. TOP CONTROL When the temperature inside the projector exceeds the normal temperature, the projector is automatically shut down to protect the inside of the projector.
Maintenance and Cleaning Cleaning the Air Filters Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat build up and adversely affect the life of the projector. Clean the air filters following the steps below. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet.
Maintenance and Cleaning Cleaning the Projection Lens Follow these steps to clean the projection lens. Disconnect the AC power cord before cleaning. 2 Softly wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use lens cleaning paper or a commercially available air blower to clean the lens. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface.
Maintenance and Cleaning Lamp Replacement When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator emits yellow light. If this indicator emits yellow light, replace the lamp with a new one promptly. Top Control POWER VOL WARNING This indicator emits yellow light when the life of the projection lamp draws to an end. CAUTION LAMP REPLACE CAUTION Allow a projector to cool, for at least 45 minutes before you open the Lamp cover.
Maintenance and Cleaning Lamp Replace Counter Be sure to reset the lamp replace counter after the lamp is replaced. When the lamp replace counter is reset, the LAMP REPLACE indicator stops emitting yellow light. Turn the projector on, press the MENU button and the OnScreen Menu will appear. Press the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. 2 Press the Point d button to move the red frame pointer to the Lamp counter reset item and then press the OK button.
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described in "Connecting to a Computer" and “Connecting to Video Equipment” on page15,16. – Make sure all equipment is connected to AC outlet and the power is turned on. – When you operate the projector with a computer and it does not project an image, restart the computer.
Appendix Some displays are not seen during the operation. – Check the Display item. (See “Setting” on page 38.) PIN code dialog box appears at start-up. – PIN code lock is being set. Input a PIN code (1234 or numbers you have set). (See “PIN code lock” on page 17 and 43.) The Remote Control Unit does not work. – Check the batteries. – Make sure no obstruction is between the projector and remote control unit. – Make sure you are not too far from the projector when using the remote control.
Appendix Menu Tree Computer Input / Video Input Input Computer RGB Go to System (1) S-Video Go to System (3) Component Go to System (2) RGB( Scart ) N/A Quit Go to System (3) Video ✽N/A - - - not applicable Sound Sound Volume Mute Quit 0 - 63 On / Off Computer Input System (1) MODE 1 MODE 2 SVGA 1 ---- Image Select Standard High contrast Blackboard(Green) Custom Image Adjust Contrast Brightness Color temp. 0 - 63 0 - 63 High Mid Low XLow Adj.
Appendix Setting Video Input System (2) Auto 1080i 1035i 720p 575p 480p 575i 480i System (3) Auto PAL SECAM NTSC NTSC 4.
Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER WARNING LAMP REPLACE red/green red yellow Projector Condition The projector is OFF. (The AC power cord is unplugged.) • • • emit green light ✽ When ✽ The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. ✽ The projector is ready to be turned on with the POWER button.
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100 MHz of Dot Clock. ON-SCREEN DISPLAY 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 –––––––– –––––––– –––––––– –––––––– 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 H-Freq. (kHz) 31.47 31.47 31.47 37.86 37.86 37.
Appendix Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 10.63" x 3.27" x 7.76" (270mm x 83.1mm x 197.2mm) (not including Adjustable Feet) Net Weight 5.1lbs (2.3 kg) Feet Adjustment 0˚ to 8.0˚ Panel Resolution LCD Panel System 0.
Appendix Accessories Owner's Manual AC Power Cord Remote Control Unit and Batteries VGA Cable Lens Cover with String Soft Carrying Bag PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
Appendix Configurations of Terminals COMPUTER INPUT/S-VIDEO INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG) Terminal : HDB15-PIN 4 5 10 15 14 2 3 9 8 13 1 7 12 6 11 1 2 3 4 5 6 7 8 Red (R/Cr) Input / Output Green (G/Y) Input / Output Blue (B/Cb) Input / Output ----Ground (Horiz.sync.
Appendix PIN code label While the projector is locked with the PIN code... Put the label below (supplied) on in a prominent place of the projector's body while it is locked with a PIN code.
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON U.S.A., INC. One Canon Plaza, Lake Success, NY 11042, U.S.A. CANON CANADA, INC. 6390 Dixie Road Mississauga, Ontario L5T 1P7 Canada CANON LATIN AMERICA, INC. 703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A. CANON MEXICANA, S.DE R.L.DE C.V. Blvd. M. A. Camacho No.138, Piso PB 15, 16 y 17, Col. Lomas de Chapultepec, C.P. 11000 México, D.F. México CANON EUROPA N.V. P.O.
