User`s manual

T460/461/T462 Manual 26th Sept 2008. V2.79 Part B © JED Microprocessors Pty Ltd

Sanyo/Eiki Group 8, Sanyo PLC-XP50/XP51/XP55/XP56/XP57/XP100, PLC-XT20/XT21/XT25/XT35, PLV-75/80,

Christie LW300, LX37/LX40/LX45/LX50/LX55/LX380/LX450, LX650

Eiki LC-W3, LC-X60/X70/X71/X80, LC-XG250/XG300/XG450,

Canon LV-7555, LV-7565, LV-7575

Separate commands are provided FOR ALL CHANNELS.

T460 Channel String sent Input Function (group 8)

1 C50 1 INPUT1 ANALOG RGB HDB 15 VGA

2 C52 1 INPUT1 DVI-Digital

3 C53 1 INPUT1 A/V input HDCP (via DVI to 5 RCA or DVI-DVI cable)

HDCP = “High-bandwidth Digital Content Protection”

4 C23 2 INPUT2 Composite (via 1 BNC)

5 C24 2 INPUT2 Component Y, Pb/Cb, Pr/Cr (via 3 BNC)

6 C25 2 INPUT2 Computer (via 5 BNC)

7 C33 3 INPUT3 Composite Video (RCA)

8 C34 3 INPUT3 S-Video

Don’t forget to set all unused T460 channels to “Skip” to jump over blank/unused inputs.

Sanyo/Eiki Group 9 PLC-SU/XU32 (This is a weird one, as theoretically SU/XU32 will NOT use codes past C07, but it

DOES!) PDG-DXT10L (see* below)

T460 Channel String sent Input Function (group 9)

1 C05 1 INPUT1 ANALOG MODE SET (HD DB15 VGA) / *Computer 1

2 C06 2 INPUT2 RGB MODE SET / *Computer 2

3 C07 2 INPUT2 VIDEO MODE SET (COMPOSITE) / *Computer 3

4 C08 3 INPUT3 VIDEO MODE SET (COMPOSITE) / *Component

5 C25* 2 INPUT2 ANALOG RGB (HDB 15 VGA) *Not DXT10-L

6 C26* 2 INPUT2 SCART (via VGA to SCART 21pin cable) *Not DXT10-L

7 C33 3 INPUT3 Composite Video (RCA)

8 C34 3 INPUT3 S-Video

Don’t forget to set all unused T460 channels to “Skip” to jump over blank/unused inputs.

Sanyo/Eiki Groups 10, Sanyo PLC-SU70, PLC-SW30/SW35, XE31/40/50, XL40/XL50,

PLC-XU41/XU47/XU48/XU51/XU70/ XU73/XU74/XU75/XU78, Canon LV-X4, LV-7230, Eiki SB22/XA20/

XB22/XB23/XB24/XB28/SD10/SD12/SD15, Group 16: Eiki XA20, San PLC-XW50/55/56. Group 17: XE32, XW60

Separate commands are provided FOR ALL CHANNELS.

T460 Channel String sent Input Function (group 10)

1 C50 1 INPUT1 ANALOG RGB HDB 15 VGA

2 C51 1 INPUT1 SCART (via VGA to SCART 21pin cable)

3 C54 1 INPUT1 Component Y, Pb/Cb, Pr/Cr (via 3 RCA to VGA cable)

4 C25/C06 * 2 INPUT2 ANALOG RGB (HDB 15 VGA) ** (some only) *XE32, XW60

5 C33/C07 * 3 INPUT3 Composite Video (RCA) * XW50/55/56, XA20, XW60

6 C34 3 INPUT3 S-Video (on some, via HDB 15 VGA connector)

Don’t forget to set all unused T460 channels to “Skip” to jump over blank/unused inputs.

** Not Sanyo PLC-SW30, XW50/55/56, EIKI LC-SD10, XA20