MP L6000 USER’S MANUAL Canon
MP-L6000—USERS MANUAL/V000/12-97 MP-L6000—USERS MANUAL/V000/12-97 CANON/MPL-6000/UM - File: L6_TP.eps W.
Copyright This manual is copyrighted by Canon Computer Systems, Inc. (CCSI) with all rights reserved. Under the copyright laws, this manual may not be reproduced in any form, in whole or part, without prior written consent of CCSI. ©1997 Canon Computer Systems, Inc. Disclaimer Canon Computer Systems, Inc. has reviewed this manual thoroughly in order to make it an easy to use guide for your Canon MultiPASS L6000 system.
USERS IN U.S.A. PRE-INSTALLATION REQUIREMENTS FOR CANON FACSIMILE EQUIPMENT A. Location Supply a suitable table, cabinet, or desk. See Appendix A for the unit’s dimensions and weight. B. Order Information 1. Only a single line, touch-tone or rotary telephone set is to be used. 2. Order an RJ11-C modular jack (USOC code), which should be installed by the phone company. If the RJ11-C jack is not present, installation cannot occur. 3.
IN CASE OF EQUIPMENT MALFUNCTION Should any malfunction occur which cannot be corrected by the procedures described in this User’s Manual, disconnect the equipment from the telephone line or unplug the power cord. The telephone line should not be reconnected or the power cord plugged in until the problem is completely resolved. Users should contact Canon Authorized Service Facilities for servicing of equipment.
USERS IN CANADA PRE-INSTALLATION REQUIREMENTS FOR CANON FACSIMILE EQUIPMENT A. Location Supply a suitable table, cabinet, or desk. See Appendix A for the unit’s dimensions and weight. B. Order Information 1. Provide only a single-line to touch-tone or rotary telephone set terminated with a standard 4-pin modular phone plug. (Touch-tone is recommended if available in your area.) 2. Order an RJ11-C modular jack (USOC code), which should be installed by the phone company.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier.
CDRH Regulations The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States. Use of controls, adjustments or performance of procedures other than those specified in this User’s Manual may result in hazardous radiation exposure.
UserÕs Manual This manual offers detailed information on how to operate your MultiPASS L6000. It includes how to use the MultiPASS as a printer, how to send and receive faxes, and how to copy and scan documents. It also includes maintenance, troubleshooting, and specifications.
Contents 1 2 Introduction Supplies and Accessories.................................................................................... Toner Cartridges ........................................................................................ Customer Care Center ..................................................................................... Servicing the MultiPASS L6000 ................................................................ Important Safety Instructions .....................................
3 4 Using the MultiPASS Desktop Manager Starting the MultiPASS Desktop Manager ....................................................... Exploring the MultiPASS Desktop Manager Window ..................................... Closing the Desktop Manager ................................................................... Using the Desktop Manager Folders ................................................................ System-defined Folders ........................................................................
5 Receiving Faxes Receiving Documents ...................................................................................... 5-2 Receiving Documents Automatically—Fax Only Mode ............................. 5-2 Receiving Both Documents and Telephone Calls Automatically— FaxTel Mode .......................................................................................... 5-2 Receiving Documents Manually—Manual Mode ...................................... 5-3 Using an Answering Machine—Ans. Machine Mode ....
8 9 Annotating a Document .................................................................................. Features of the Document Viewer Window ............................................... Adjusting Your View of the Document ...................................................... Adding Annotations to Your Document .................................................... Revising Your Annotations .........................................................................
10 Troubleshooting Paper Jams ....................................................................................................... 10-3 Jams in the Automatic Document Feeder (ADF) ....................................... 10-3 Jams in the Output Slots ........................................................................... 10-5 Jams Inside the Unit .................................................................................. 10-6 After Clearing a Paper Jam ..........................................
xiv MP-L6000—USERS MANUAL/V000/12-97
Introduction Introduction 1 MP_L6000 Thank you for purchasing the Canon MultiPASS™ L6000—the multitalented laser printer for your home office and the whole family. We are sure that your MultiPASS L6000 will provide all you need in one machine: laser printer, plain paper fax, PC fax, copier, and scanner. This chapter introduces you to the MultiPASS L6000.
Supplies and Accessories Canon has an extensive dealer network equipped to offer you supplies as you need them. To find a dealer near you, call the Canon Referral Service at 1-800-848-4123. If supplies are not available from your local dealer, you can order directly from Canon by calling 1-800-385-2155. Toner Cartridges Your MultiPASS L6000 comes with one FX-3 Toner Cartridge. N For optimum printing results, Canon recommends that you use only the Canon FX-3 Toner Cartridge with your MultiPASS L6000.
Canon Canada Customer support for Canadian residents is available 24 hours a day (seven days a week) at 1-800-263-1121. Servicing the MultiPASS L6000 The Canon MultiPASS L6000 is designed with the latest technology to provide trouble-free operation. The warranty card that comes with your system describes Canon’s limited warranty, which includes the InstantExchange warranty program. Be sure to read the warranty information to find out about the different service options available to you.
❍ Place the MultiPASS on a sturdy level surface. Do not place it on an unstable cart, stand, or table. If the unit falls, it could be seriously damaged. ❍ Do not use the MultiPASS near water. If you spill liquid on or into the unit, unplug it immediately and call the Customer Care Center. ❍ Slots and openings in the unit and on the back or bottom are provided for ventilation. To ensure reliable operation of the MultiPASS and to protect it from overheating, do not block or cover these openings.
Main Components of the MultiPASS L6000 SUPPORT TRAY HOLDS PRINTED DOCUMENTS AS THEY EXIT IN FACEDOWN POSITION MULTI-PURPOSE TRAY HOLDS 100 SHEETS OF PLAIN PAPER PAPER REST SUPPORTS PAPER STACKED IN THE MULTI-PURPOSE TRAY MANUAL FEED SLOT HOLDS INDIVIDUAL SHEETS OR ENVELOPES SUPPORT TRAY HOLDS DOCUMENTS AS THEY FEED INTO ADF PAPER GUIDES ADJUST TO WIDTH OF PAPER FACEDOWN DELIVERY SLOT—PAPER EXITS IN FACEDOWN POSITION IN COLLATED SEQUENCE AUTOMATIC DOCUMENT FEEDER (ADF) HOLDS DOCUMENTS TO BE SCANNED (UP
Back View MP_L6000_BACK RELEASE LATCH POWER CONNECTOR BI-DIRECTIONAL PARALLEL PORT TELEPHONE/ ANSWERING MACHINE JACK TELEPHONE LINE JACK Inside the MultiPASS PAPER RELEASE LEVER FX-3 TONER CARTRIDGE COMPARTMENT TRANSFER CHARGING ROLLER FRONT COVER 1-6 Introduction MP-L6000—USERS MANUAL/V000/12-97 Chapter 1 MP_L6000_INSIDE FIXING ASSEMBLY
Using the Operator Panel 4 RESOLUTION 6 ONE-TOUCH SPEED DIAL/FUNCTION BUTTONS 5 7 FUNCTION 3 LCD DISPLAY 2 RECEIVE MODE ALARM 8 ARROW BUTTONS MP_L6000_OPPANEL 1 DOCUMENT FEED LEVER Introduction This section presents a brief description of the operator panel on the MultiPASS L6000. 13 NUMERIC BUTTONS 12 REDIAL/PAUSE 9 STOP 11 CODED DIAL 10 START/COPY Document feed lever Set this lever to the left ( ) for automatic feed or to the right ( ) for manual document feed.
4 Press to select the Resolution the MultiPASS will use for the document you are faxing or copying. 5 ALARM light Flashes when an error occurs, when the MultiPASS is out of paper or ink, or when received faxes are stored in memory. 6 One-touch Speed Dial/Function buttons Use for one-touch speed dialing, entering user information, and printing documents stored in memory. 7 button Use to register user settings or to print faxes stored in the MultiPASS L6000’s memory.
The paper you load in the multi-purpose tray is used for printing documents or for incoming faxes. You can use any plain paper (such as copier paper). When the message LOAD PAPER appears in the LCD display, you need to add paper to the multi-purpose tray. This tray holds approximately 100 sheets of plain paper. Introduction Loading Paper in the Multi-purpose Tray 1 Fan the paper. ❍ For best results, fan the paper before loading it.
3 Insert the stack of paper. ❍ Insert the paper with the print side facing you and top edge first into the multi-purpose tray. (The multi-purpose tray is behind the manual feed slot.) MULTI-PURPOSE TRAY PAPER_2 ❍ Insert the stack until it stops, but do not force it in. MANUAL FEED SLOT 4 Adjust the paper guides to the width of the paper. ❍ Make sure there is no space between the paper guides and the stack of paper. NO SPACE PAPER_3.
You can use the MultiPASS L6000 to fax, copy, or scan documents that are printed on standard letter, legal, or A4 size paper. Follow these guidelines to prepare your documents.
Loading the Document You can load up to 20 letter or A4 size sheets and up to 10 legal size sheets at a time into the Automatic Document Feeder (ADF). 1 ❍ For a multiple-page document, fan the sheets and tap the document on a flat surface to even the stack. TAP Stack your documents. 2 ❍ Adjust the document guides to the width of the document. FAX_FEED Adjust the document guides.
3 ❍ Gently insert the document facedown (letterhead first) into the ADF until it stops. DOC_IN Introduction Feed the document. The document is now ready for scanning. The MultiPASS automatically feeds the pages one by one from the bottom of the stack. If you have problems feeding a multiple-page document, remove the document and re-stack it tapping the edges on a flat surface. If problems persist, feed one page at a time.
Adding Pages to the Document If you want to add pages while the MultiPASS is sending a document, wait until the last page is feeding into the MultiPASS and then insert the new sheets. Insert the first new page so it overlaps the last page by about one inch (2.5 cm). ❍ Always wait until the last page is being fed into the MultiPASS before you add new pages. ADDING_PAPER ❍ Insert the new page so that it overlaps the last page by about an inch (2.5 cm).
Always set the document feed lever to single sheets and manually feed the following types of documents: ❍ Thick paper Introduction ❍ Thin paper ❍ Small documents (postcards, business cards) ❍ Documents with uneven surfaces ❍ Photographs ❍ Special types of paper Identifying Your Documents When sending a document, the following information is printed out by the receiving fax: your fax number, your name, and the current date and time.
The top line includes the name of the receiving party if you send the document using one-touch speed dialing, coded speed dialing, or group dialing and you registered the party’s name. It also includes the page number. N 1-16 You entered your fax header information during the MultiPASS installation procedure. If you followed the installation procedure, this information will be printed on the top of your outgoing faxes.
Printing With the 2 This chapter describes how to use the MultiPASS L6000 to print your documents. Once you have installed the MultiPASS Desktop Manager, you can use the MultiPASS for all your printing needs.
When selecting or loading paper, please remember the following: ❍ Attempting to print on damp, curled, wrinkled, or torn paper can cause paper jams and poor print quality. ❍ Use cut-sheet paper only. You cannot use multipart paper. ❍ Highly textured or extremely smooth or shiny paper does not print well. ❍ The laser printing process uses high temperatures to fuse toner to the paper. Use paper that will not melt, vaporize, discolor, or emit dangerous fumes at temperatures near 338°F (170°C).
Printing a Document This procedure describes the general steps required for printing from various Windows applications. The exact steps for printing a document may vary depending on the application program you are using. Refer to your software application’s documentation for the exact printing procedure. 1 Start your application. ❍ Start the program you use to create documents, and open the document you want to print. ❍ From the File menu, choose Print Setup. PTR_PTR.
Printer Setup Within Windows You can use the MultiPASS with all your Windows 95 applications. Be sure to set the MultiPASS L6000 as the default printer for all your Windows operations. Most of your printing operations are controlled by your software application. The following sections describe how you set certain options directly from the printer driver; you only need this information if your application does not control printing.
Using the Windows Tabs The MultiPASS Printer Driver for Windows has several tabs from which you can select your printing options and learn about your printer driver as well as your MultiPASS L6000. ❍ General ADD COMMENTS HERE L6000_DR1 Printing This tab allows you to add comments regarding the printer driver and print a test page or a separator page. (You see this tab when you open the Properties dialog box from the Printers folder, not from within a Windows application.
❍ Paper This tab allows you to specify page orientation, paper size, and type of print media. SPECIFY SIZE OF PAPER SPECIFY TYPE OF PAPER SPECIFY PAPER FEED METHOD L6000_DR3 SPECIFY PAGE ORIENTATION ❍ Graphics This tab allows you to specify print quality and print model.
❍ Setting ENABLE OR DISABLE SETUP ANALYZER ENABLE OR DISABLE TONER SAVING FEATURE Printing SAVE YOUR CUSTOM PRINT SETTINGS Be sure to use the Windows 95 Help features to find out more about the options on these screens. Specifying Your Printing Options Be sure to use your on-line help to find out about the settings available for each printing option. ❍ To move between the Windows tabs, click on any of the tabs. ❍ To select the settings and exit, click the OK button.
The Paper Path Understanding how paper feeds through the MultiPASS will help you to determine how to load paper and handle paper jams. The page travels first to the FX-3 Toner Cartridge. Here a laser beam “draws” the print image on the drum, then the drum applies toner to the page. The page then travels to the fixing assembly where the toner is fused to the page. The page then exits the unit from the front or top.
Selecting Paper Delivery Received faxes, copies, and printed documents can be delivered through the faceup or facedown delivery slot. Choose paper delivery according to the job the MultiPASS is performing and the type of print media you are using. PAPER DELIVERY SELECTOR FACEUP DELIVERY Facedown Delivery Use facedown delivery for most jobs and when using plain paper only (17 to 24 lbs or 64 to 90 g/m2). Printed pages are stacked in the order printed in the facedown delivery slot.
mark. FACE_DOWN_DELV ❍ Make sure the paper delivery selector is set up to the FACEDOWN DELIVERY Faceup Delivery Use faceup delivery when printing on media other than plain paper, such as transparencies, labels, thick paper (up to 28 lb or 105 g/m2), or envelopes. With faceup delivery, the sheet or envelope travels straight through the unit without bending, and thus prevents curling. mark.
Loading Paper in the Multi-purpose Tray You can stack up to approximately 100 sheets of plain paper (20 lb or 75 g/m2) in the multi-purpose tray. The multi-purpose tray holds letter, legal, and A4 size paper, provided that its weight is 24 lb (90 g/m2) or less. To load the paper, follow the steps starting on page 1-9. Loading Envelopes in the Multi-purpose Tray Prepare the envelopes. ❍ Arrange the stack of envelopes (up to 7) on a firm surface and press down firmly on the edges to make the folds crisp.
3 MULTIPURPOSE TRAY INSERT_STACK Insert the stack until it stops, but do not force it. MANUAL FEED SLOT 4 ADJUST_GDE Adjust the paper guides to the stack of envelopes.
5 ❍ Be sure to use faceup delivery when printing on envelopes. FACE_UP_DELV Move the paper delivery selector down to the mark. Printing FACEUP DELIVERY Your MultiPASS is now ready to print. N You can change the orientation of the envelopes through your application software. Check the orientation before printing.
Loading Paper Manually You can load paper manually, one sheet at a time, using the manual feed slot. You can load plain paper (17 to 28 lb or 64 to 105 g/m2), transparencies, labels, envelopes, and other special papers. 1 ❍ Adjust the paper guide to the approximate width of the sheet of paper. LOAD_ADJUST_GDE Open the paper guides. 2 ❍ Make sure the print side is facing you and the top edge goes into the slot first. ❍ Insert the sheet until it stops, but do not force it in.
3 Adjust the paper guides to the sheet of paper. ❍ Make sure there is no space between the paper guides and the sheet. 4 FACEUP DELIVERY Your MultiPASS is now ready to print. N ❍ If you insert a sheet into the manual feed slot when there is paper stacked in the multi-purpose tray, the unit will feed the sheet from the manual feed slot. ❍ Insert a sheet in the manual feed slot only when the previous sheet has come out from the delivery slot.
2-16 Printing With the MultiPASS L6000 MP L6000—USERS MANUAL/V000/12-97 Chapter 2
Using the MultiPASS 3 The MultiPASS Desktop Manager is a full-featured Windows application that enables you to use your MultiPASS L6000 from your computer. The MultiPASS Desktop Manager coordinates the printing, PC faxing, and scanning functions of the MultiPASS L6000.
Starting the MultiPASS Desktop Manager When you start Windows or open the Desktop Manager, the MultiPASS Background is automatically started as well. The MultiPASS Background enables and monitors the communication between the Desktop Manager and the MultiPASS L6000. When you exit the Desktop Manager, you close only the Desktop Manager window. Any documents you have set up to PC fax or print remain active.
Exploring the MultiPASS Desktop Manager Window When you start the MultiPASS Desktop Manager, you see a screen similar to this: MENU BAR NEW_DESKTOP_TIF TOOLBAR FOLDERS LIST WORK AREA COMMAND BAR Menu Bar The menu bar contains commands that enable you to perform the various Desktop Manager tasks. Some of the commands can also be accessed by their corresponding icons on the toolbar or command bar. Toolbar The toolbar provides quick access to certain Desktop Manager tasks.
Folders List The folders list contains folders that store your fax and scan documents. The list contains both system-defined folders, provided automatically when you install the software, and user-defined folders. System-defined folders include In Box, Out Box, Scan, Sent Fax, and Trash. User-defined folders are folders you can create yourself. Work Area The work area appears to the right of the folders list and displays one of the documents within the open folder.
Status Line The status line displays information about the selected folder or document, such as the name of the folder or document and its creation date. You cannot edit this information. If the Address Book is open, the status line displays information about the selected Address Book entry. Closing the Desktop Manager When you exit the Desktop Manager, you close only the Desktop Manager window. Any documents you have set up to PC fax or print remain active.
A document remains in a system-defined folder until you move it to a user-defined folder, or delete it. In Box The In Box folder stores all incoming faxes received by the Desktop Manager. Each received fax displays a system-assigned name—fax nnnn, where nnnn is a number of up to four digits which is unique within the Desktop Manager. You can later change the name to something more descriptive. Out Box The Out Box folder is a chronological list of jobs you want to process.
Trash The Trash folder holds any documents that you want to delete. Once you drag a document from another folder to the Trash folder, you can hold the document until you are ready to delete it. N If you select a document and press the Delete key, or if you drag a document to the Delete icon, the document is deleted immediately. It is not stored in the Trash folder. User-defined Folders You can create up to 255 folders for your own use.
When you first open the Desktop Manager, the documents are displayed in Document View. However, you can change to List View at any time. If the number of documents within a folder exceeds the available work area, horizontal and/or vertical scroll bars appear. You can then scroll the work area to view your documents. To open a folder, simply click the desired folder in the folders list. Document View Document View presents each individual document as a thumbnail of the document.
List View VIEW_LIST List View presents the documents within the open folder as a list. Each document on the list displays an icon representing the document type, along with other pertinent information about the document (such as the name, page count, disk storage size, and date and time of creation). List View is available for all folders, both system- and user-defined.
LIST_ORDER To change the order of the list, click the title of the appropriate column at the top of the list. Setting Up the Address Book You set up the Address Book to create an easily accessible list of names and fax and/or phone numbers for your business and personal contacts.
Now click Address Book. The MultiPASS Desktop Manager displays the Address Book window: ADD_BOOK ADDRESS BOOK ENTRIES STATUS LINE ❍ Address Book Entries Address Book entries are listed by row. The columns indicate the Address Book entry type (individual or group), name and address information, and phone and fax numbers. Address Book entries can be sorted based on a chosen column of information.
❍ Group A group entry identifies the two or more individual Address Book entries to whom you repeatedly send the same fax. For example, you can set up a group to include those individuals involved in a particular business project. When you specify the group entry as the fax recipient on your fax, the fax is sent to each individual in the group. Sorting the Address Book The Address Book is sorted alphabetically by last name. You can change the order of the list based on the column titles for the list.
AB_EDIT To add an individual entry, click the New Individual button on the toolbar. To edit an individual, select the Address Book entry and click the Edit button. Enter the appropriate information. ❍ You must type at least a First Name or Last Name and a Phone or Fax number before you can click Add. MultiPASS Desktop Manager ❍ You can enter 20 characters in the First and Last Name text boxes, 40 characters in the Company Name text boxes, and 32 characters in the Phone and Fax Number text boxes.
Adding and Editing a Group Address A group address contains addresses previously set up in the Address Book, either individual addresses or other group addresses. The New Fax Group dialog box displays two lists—a list of all Address Book entries previously set up, and the list of addresses included in the group. You select addresses from the Address Book to include in the group. You’ll want to add addresses to a group when you will be PC faxing to this group.
❍ If adding a new group, click Create. ❍ If editing a group, click Replace. Using a Group Address When you specify a group address when sending a fax, the individual addresses for the contained group are listed. If you specify more than one group address for a fax, and each group contains the same individual address, the duplicate address is removed. Separate fax jobs are created for each recipient in the group.
1 ❍ You see this screen: AB_IMPT To import addresses from a text file, click on the Import button. 2 AB_IMPT_2 In the Import Address Book dialog box, specify the location and filename to import. Then click OK. ❍ In the Assign Field Names dialog box, the address information is listed in columns, with a column title that identifies the type of information within the column. The button above the column titles enables you to reassign the column titles where necessary.
4 Click Import. ❍ When the appropriate names appear at the top of each column, click Import. Exporting the Address Book You can export the Address Book from the MultiPASS Desktop Manager to an ASCII text file. The address information can be separated by either commas or tabs. ❍ If you choose to have the address information separated by commas, the text file extension is .CSV. ❍ If you choose to have the address information in the text file separated by tabs, the text file extension is .TXT.
2 Assign the appropriate name to each column as the title. ❍ To remove a field name from the column heading, drag the column heading text off the dialog box. ❍ To assign the correct name, drag the titled button to the column title. 3 Click Export. ❍ When the appropriate names appear at the top of each column, click Export. AB_EXPT_2 ❍ In the Export Address Book dialog box, select the file type (.CSV or .TXT), location, and filename for saving the file. Then click OK.
SET_SPDIAL To set up your speed dialing assignments, select Setup from the Desktop Manager menu bar, and then click on the Speed Dial tab. Assigning an Individual Recipient to a Speed Dial Code MultiPASS Desktop Manager To assign a fax recipient to a speed dial code: ❍ In the Address Book list box, select the recipient that you want to assign to a speed dial code. ❍ Select the speed dial code to which you want to assign the Address Book, and click Add.
Defining a Group Speed Dial Code You’ll want to assign multiple recipients to a speed dial code when you will be sending plain paper faxes to this group. If you will be PC faxing, you can set up the group in your Address Book. See page 3-14 for details. To assign two or more recipients to a speed dial code: ❍ On the Speed Dial tab, make sure the desired recipients for your group are set up as individual speed dial assignments.
❍ In the Speed Dial list box, select the first recipient and click Add. Repeat this procedure until the desired recipients are included in the Member(s) list box. ❍ To remove a member from the group, select the member in the Member(s) list box and click Remove. ❍ When all the desired members are listed in the Member(s) list box, click OK to save your group. ❍ To close the dialog box without saving your group, click Cancel. ❍ To complete the operation, click OK to close the Setup Options dialog box.
FAX_LOG.TIF You can also click on the Fax Log icon on the toolbar. ❍ In the Fax Log dialog box, click a specific fax document to review additional information in the Details and Log Note boxes. ❍ Click the Print button to print the Fax Log.
Sending Faxes With the 4 You can use the MultiPASS L6000 to send paper faxes or PC faxes. PC faxing is the ability to send a fax from an application without first printing the document. Using the MultiPASS L6000 and the MultiPASS Desktop Manager, you can PC fax documents from any Windows application that supports printing. Before sending faxes, you may want to set up the numbers you plan to use for automatic dialing methods such as one-touch speed dialing.
Sending a Document The MultiPASS starts sending a document while it is being scanned into memory. When scanning a multipage document, the unit calls the other party as the first page is being scanned. Once connection is made, the MultiPASS begins to transmit the information while the remaining pages are being scanned. This is called Memory Sending. Regular Dialing 1 Feed the document. ❍ Place the document facedown in the Automatic Document Feeder (ADF). See page 1-12.
2 Dial the other party’s fax number. ❍ Use the numeric buttons to dial the number. ABC 1 GHI 4 PRS 7 2 JKL 5 TUV 8 OPER DEF 3 MNO 6 WXY 9 TEL= 555 7899 SYMBOLS 0 TONE ❍ To enter a pause, press REDIAL/PAUSE. • A pause within a number (p) is two seconds. (You can enter more than one.) • A pause at the end of a number (P) is ten seconds. 3 Press START/COPY. START/COPY The MultiPASS begins scanning the document, and dials the number.
❍ When the document has been sent successfully, the display shows this message. TRANSMITTING OK The MultiPASS automatically redials if the receiving fax does not answer, if the line is busy, or if a transmission error occurs. You can specify the number of times it redials using the Automatic Retries option in the Send Fax dialog box of the MultiPASS Desktop Manager (see page 8-4). If all redial attempts fail, the MultiPASS beeps intermittently for a few seconds.
2 Use automatic dialing. ❍ Press the one-touch speed dialing button (1 through 6) assigned to the number you wish to fax to; the name you assigned to that button is displayed. CANON FAX BACK OR ❍ Press CODED DIAL and enter the appropriate two-digit coded speed dialing code. CODED DIA CCSI/MKT ❍ If you make a mistake, press STOP. Then press the correct one-touch speed dialing button or press CODED DIAL and re-enter the code. 3 Press START/COPY.
Sending a Document Using Group Dialing If you frequently send plain paper faxes to the same group of people, you can use the MultiPASS Desktop Manager to assign a “group” of numbers to a speed dial code. See page 3-20. 1 Feed the document. ❍ Place the document facedown in the ADF. DOCUMENT READY 2 Choose the group you wish to send to. ❍ Press the one-touch speed dialing button or press CODED DIAL and the code under which you registered the group. TEL=CANON GROUP 1 3 Press START/COPY.
❍ If there is no group registered under the one-touch speed dialing button or the two-digit code, the LCD displays the NO TEL # message. Make sure you entered the correct number and that the group has been registered correctly to a speed dial code. See page 3-20. ❍ If you make a mistake when dialing, press STOP. You can try again. Redialing Manual To start dialing again, just press the REDIAL/PAUSE button. The MultiPASS redials the previous number you dialed with the numeric buttons.
To Cancel Automatic Redialing To cancel automatic redialing, press the STOP button. However, you cannot cancel redialing while the LCD displays AUTO REDIAL (the unit is waiting to redial). In this case, wait until dialing begins and then press STOP to cancel redialing. The MultiPASS asks you to confirm: STOP CANCEL? *YES #NO To cancel the redialing, press *. The MultiPASS L6000 beeps and the LCD displays: TX/RX CANCELLED TX/RX NO.
Manual Sending If you would like to speak with the other party before sending a fax to them, you may do so; this is called manual sending. To use manual sending, you must have a telephone connected to the MultiPASS. 1 Feed the document. ❍ Place the document facedown in the ADF. DOCUMENT READY 2 Pick up the telephone and dial the other party’s fax number.
Messages Displayed During Sending When sending a document, the MultiPASS displays the following messages as the call progresses. TRANSMIT TX/RX NO. XXXX When it is finished sending the document, the MultiPASS beeps once; the LCD displays: TRANSMITTING OK Cancel Sending To stop sending before a fax is complete, follow these steps: 1 Press STOP. ❍ If you are sending manually, the transmission is cancelled immediately.
Sending a Document to More Than One Location (Sequential Broadcasting) Sequential broadcasting sends one document to more than one location. You can send to a total of 57 destinations as follows: One-touch speed dialing Coded speed dialing Regular dialing (numeric buttons dialing) = up to 6 destinations = up to 50 destinations = 1 destination only You can enter the one-touch and coded speed dialing numbers in any order.
2 Dial the other party’s number. TEL= 4567899 ❍ Simply enter the numbers one after the other: press the desired one-touch speed dialing button or press CODED DIAL followed by the two-digit code. ❍ If you are sending to group dialing destinations, use the one-touch speed dialing buttons and the CODED DIAL button (along with the two-digit codes) to enter the groups. ❍ You must press the second speed dialing number within five seconds of pressing the first one.
❍ The MultiPASS begins the operation approximately ten seconds after you press the last button (five seconds if you press only one button) even if you do not press START/COPY. ❍ The MultiPASS dials the destinations in numerical order starting with the coded dial numbers, then the one-touch numbers, and finally the regular-dial number (regardless of the order in which you entered the numbers). ❍ To cancel a transmission, press STOP during the dialing or transmission.
The MultiPASS has three resolution settings: ❍ STANDARD Standard resolution (203 × 98 dpi) is adequate for most text documents. ❍ FINE Fine resolution (203 × 196 dpi) is suited for documents with fine print (smaller than the print in this sentence). ❍ PHOTO Photo resolution (203 × 196 dpi with halftones) is for documents that contain photographs.
1 Press the RESOLUTION button. ❍ The LCD shows the current resolution. STANDARD 2 Press the RESOLUTION button again. ❍ Press RESOLUTION once or twice more to display the resolution you want (STANDARD, FINE, or PHOTO). STANDARD FINE PHOTO ❍ After about five seconds, the LCD returns to Standby mode. FaxTel Setting the Contrast Contrast is the difference in brightness between the lightest and darkest parts of a printed document.
Sending PC Faxes You can create and send a PC fax from any Windows application that supports printing or you can create a fax in the MultiPASS Desktop Manager. You can PC fax the document immediately, send it at a specific time, or hold it in the Out Box to be sent at a future time. Sending a PC Fax From a Windows Application 1 Create a PC fax document. ❍ Open the Windows application. ❍ Create and save the document. 2 Open the Print window in the application.
SEND_FAX1 ❍ The Send Fax dialog box appears: 3 ❍ Choose individuals or fax groups from the Address Book list on the left by clicking a name and clicking the Add button. • To remove a name from the Recipients list, click the name and click the Remove button. • To add a new entry to the Address Book, click New. ❍ For a single, one-time recipient, enter the appropriate information in the Last Name, First Name, Company, Prefix, and Fax Number boxes.
❍ To send the fax with any annotations that were added to the document using the MultiPASS Desktop Manager Document Viewer, click Include Annotation. ❍ To add a reference comment for the fax log, enter the text in the Log Note box. 4 To send the PC fax, click Send Now, Send Later, or Hold. ❍ Send Now Sends the document right now. ❍ Send Later Saves the document in the Out Box. ❍ Hold Places the document in the Out Box until you select it and specify a time for it to be sent.
Identifying the Fax Sender You can enter your name and phone number in the From and Phone boxes. After sending the first PC fax, this information is automatically displayed the next time you send a PC fax. You can change the fax sender information as needed. Entering a Memo You enter a memo to be included on the fax cover page. The memo appears on the cover page if the cover page is designed to include it.
Creating a Fax Memo in the MultiPASS Desktop Manager You can create and send a Fax Memo that consists of a coversheet with a message you type. This allows you to quickly send a memo without using another Windows application. MDM_FAX_1 Simply choose Fax Memo from the File menu. The Send Fax dialog box appears: Specify this information exactly like you do for a regular PC fax. See page 4-17.
Preparing the Cover Page Background The cover page background provides the permanent information and any graphics you want included on your cover page. You then position the variable fields in the appropriate locations on the background. For example, for your background, you may want to include heading text that provides your company name and address information, labels for the variables fields (such as To: and From:), and one or more graphics that may represent your company logo or your signature.
3 Open and save the document. ❍ Locate the held fax document and open it in the Document Viewer. • Double-click the document, select the document and click Open Document on the File menu, or drag the document to the Open Document button on the toolbar. ❍ With the document open in the Document Viewer, export the document in a TIFF file format. • On the File menu, click Export. In the Export dialog box, specify the drive, directory, filename, and file type for saving the document. Click OK.
Using the Cover Page Designer The Cover Page Designer window consists of the following components. MENU BAR MDM_CPD3 TOOLBAR VARIABLES BIN LAYOUT AREA NEW COVER OPEN PRINT ITALIC ALIGN BOTTOM ALIGN RIGHT UNDERLINE BOLD SAVE ALIGN LEFT ALIGN TOP In addition to the buttons, the toolbar also provides you with dropdown list boxes that enable you to select a font and font size for the text of a variable field.
Variables Bin The variables bin contains the fields of information you want to include on the cover page for your fax. When you use the cover page for sending a fax with the Desktop Manager, these fields are automatically filled in with the appropriate information for that specific fax transmission. Layout Area The layout area allows you to visually create and edit the features of your cover page. The size of the layout area corresponds to the size of a standard fax page.
3 Save your cover page. ❍ When you have completed the cover page design, click Save on the File menu or toolbar. ❍ In the Save Cover Page Template dialog box, enter the name of your cover page and click OK. Inserting Variable Fields You insert variable fields that are filled in with actual data when you attach the cover page to a particular fax you are sending. You can choose any or all of the available fields, and place each at the desired location in the layout area.
❍ To select a field in the layout area: • • • To select a single field, click the field. To select more than one field, hold down the Ctrl key and click the desired fields. To select all fields, on the Edit menu, click Select All. ❍ To move a field, drag the selected field to a new location. ❍ To delete a field, select the field and click Delete on the Edit menu or press the Delete key. Resizing a Field With the exception of the Memo field, most of the variable fields consist of a single line of text.
To change the text attributes, select the field you want to change in the layout area. Now choose the appropriate text attributes: ❍ Select the font and font size from the drop-down list boxes on the toolbar. ❍ Click Bold, Italic, and/or Underline on the toolbar. Aligning fields When placing the variable fields in the layout area, you can align two or more selected fields, based on the position of the first field you select.
❍ In the layout area, make the appropriate changes. ❍ Save your changes. To save the changes under the same name: ❍ Click Save on the File menu or toolbar. To save the changes under a different name: ❍ On the File menu, click Save As. In the Save Cover Page Template dialog box, specify the name of the cover page, and click OK. (This retains the opened cover page under its original name.) To rename the originally opened cover page: ❍ On the File menu, click Rename.
Printing a Fax Cover Page You can print a cover page to produce a hard copy for review or to use when sending a fax directly from the MultiPASS. The hard copy includes the name of the cover page and the date last modified, printed at the uppermost edge of the page. 1 ❍ In the Print Setup dialog box, specify your print options and click OK. L6000_2.TIF With the Cover Page Designer open, on the File menu, click Print Setup. 2 Preview before printing.
you will not use the remaining commands. 3 Print the cover page. ❍ With the cover page open, click Print on the File menu or toolbar. NEW_PRINT.TIF ❍ Complete the Print dialog box and click OK.
Receiving Faxes 5 The MultiPASS L6000 has four Receive Modes: ❍ Fax Only Mode ❍ FaxTel Mode ❍ Manual Mode ❍ Answer Machine Mode You set the Receive Mode during the MultiPASS installation procedure. (See your Quick Start Guide for details.) You can change the Receive Mode and the Receive Fax options through the MultiPASS Desktop Manager. See page 8-7 for details.
Receiving Documents During reception of a fax: ❍ If the unit runs out of paper or if the toner cartridge runs out of toner, the MultiPASS receives the remainder of the document in memory. ❍ To stop receiving before the document is complete, press STOP. ❍ If the ALARM light is flashing for any reason, correct the error and then press STOP. If necessary, see Chapter 10, Troubleshooting. ❍ If an error occurs, the MultiPASS beeps intermittently for a few seconds.
If you do not pick up the telephone connected to the MultiPASS within 15 seconds (set by the Ring Time option), the unit stops ringing. It checks again to make sure the call is not from a fax machine and then hangs up. N The MultiPASS does not recognize an extension telephone connected to another phone jack (that is, not connected to the MultiPASS). If a call comes in and you pick up an extension phone, the MultiPASS will continue to ring for 15 seconds, check for a fax, and then hang up.
Receive option must be enabled in the Advanced: Receive Fax dialog box. (The default is enabled.) For details, see page 8-8. Use the telephone to receive manual calls as follows: 1. When you answer a call and hear a long beep or silence, a fax is being sent. 2. Enter the two-digit ID code on your telephone (the default code is 25). Wait for five seconds, then hang up. The MultiPASS then begins receiving the document.
Using the MultiPASS With an Answering Machine Follow these guidelines when using the MultiPASS with an answering machine: ❍ Set the answering machine to answer on the first or second ring. ❍ If the MultiPASS runs out of paper or toner in Answer Machine Mode, it receives all faxes into its memory. The faxes then print automatically when you add paper or replace the toner cartridge. ❍ When recording the outgoing message on the answering machine: • • • The entire message must be no more than 15 seconds long.
The MultiPASS can store up to 122 letter-size pages (based on the CCITT No. 1 chart). The LCD display shows REC’D IN MEMORY alternating with the error message when the memory contains documents. The MultiPASS will automatically print the contents of memory when you correct the problem. After printing the document(s) stored in memory, the MultiPASS erases the document(s) from memory.
Receiving Faxes to the MultiPASS Desktop Manager When your computer is on, you can automatically receive incoming faxes to the MultiPASS Desktop Manager. When your computer is off, the MultiPASS stores received faxes in its memory until you either print them or you turn on the computer. When you turn on the computer, you can send the faxes to the MultiPASS Desktop Manager. The MultiPASS can also print incoming faxes directly.
Printing a Received Fax When Your Computer Is Off When a document is in its memory, the MultiPASS displays the message REC’D IN FILE and alternately flashes the date. To upload the fax to the MultiPASS Desktop Manager, simply turn on the computer. If you want to print a fax that is stored in the MultiPASS’s memory without turning on the computer, follow these steps: 1 On the MultiPASS, press the FUNCTION key. FUNCTION 2 Select FILE PRINT. ❍ Use the < or > buttons to select FILE PRINT.
Using the Distinctive Ring Pattern Detection (DRPD) Feature Some phone companies offer a distinctive ring pattern (DRP) service whereby they assign two or more telephone numbers with distinctive ring patterns to a single telephone line. If your phone company offers such a service, you can have both a fax number(s) and a telephone number(s) for your MultiPASS using only one telephone line. Your MultiPASS will automatically detect incoming calls.
How DRPD Responds to Calls When there is an incoming call, the MultiPASS checks the incoming ring pattern and determines the type of pattern being received. The MultiPASS may require up to 10 seconds to determine the pattern type. During this time, any telephone device connected to the MultiPASS will not ring if Silent Receive is enabled. After the pattern is detected, the MultiPASS reacts according to how you registered the setting.
Copying and Scanning Copying and Scanning With 6 the MultiPASS L6000 You can use the MultiPASS L6000 as a copier and a scanner. This chapter describes: ❍ Setting the document feed lever ❍ Copying documents using the operator panel ❍ Scanning documents with the MultiPASS L6000 Setting the Document Feed Lever To copy or scan, you set the document in the Automatic Document Feeder (ADF). See the instructions starting on page 1-12 for details.
Copying Documents Using the Operator Panel One of the convenient features of the MultiPASS is its ability to make high-quality copies. You can make up to 99 copies of one document at a time. 1 Feed the document. ❍ Place the document facedown in the ADF. The LCD displays these messages: MEMORY USED 0% PAGIS_~3 FINE DOCUMENT READY 2 Press START/COPY. START/COPY COPY 100% 01 ❍ The display shows the size of the copy (the default is 100%) and the number of copies (the default is 1).
❍ Use PHOTO resolution when copying documents that contain photographs. This scans areas of the document that contain photos with 64 levels of gray, and results in a much better reproduction of the photograph. Copying and Scanning N ❍ Use FINE resolution for copying most text documents. ❍ STANDARD resolution is not available for making copies. 4 Select Reduction mode if necessary.
N ❍ If the LCD displays MEMORY FULL while making multiple copies of a document, do not use the multiple copy feature for copying the document. Make single copies of the document instead (as many times as required). ❍ You may be able to make multiple copies if you first print out any faxes that are stored in memory (see page 5-5). ❍ The MultiPASS makes single copies at 600 × 300 dpi and multiple copies at 300 × 300 dpi. For the higher resolution, make one copy at a time.
MP L6000—USERS MANUAL/V000/12-97 Copying and Scanning With the MultiPASS L6000 6-5 SCANICON.TIF SCAN_1.
3 SCAN_3.TIF In the Main tab, you specify the scan options for your document. ❍ Scan Mode Selects the type of image you are scanning: Black and White—Scans an image at one bit per pixel. Text Enhanced—Scans an image in grayscale, converted to black and white using Canon Image Trust technology. ❍ Scan Resolution Selects the resolution in dots per inch. Use the scroll bar to view the various resolutions, or choose Custom for further selections. Generally, a higher resolution provides better image quality.
4 5 In the Preferences tab, you specify preferred options. ❍ Text Enhanced—Use Text Enhanced instead of Black and White for OCR software This option is designed for use with OCR (Optical Character Recognition) software. Set this option to increase the contrast in black and white scanning to promote the accurate recognition of characters in OCR software. For OCR scans, set the resolution to at least 300 dpi. ❍ Color Matching This option is not applicable for the MultiPASS L6000.
6 In the L6000 tab, you specify options for a Black & White scan. ❍ Page Size Specifies the size of image you are scanning. ❍ Black & White Options Specify the Threshold, Brightness, and Contrast of the image. In the Black & White Options list box, select the desired option: Threshold Provides a high contrast evaluation of the image in terms of black and white only. Halftone Simulates the tonal range of an image with a precise pattern of lines and dots.
To start the scan, click the Preview or Scan button. ❍ If you click Preview, the image is displayed in the ScanGear window.
Scanning From a Windows Application You can use the MultiPASS to scan documents directly into a Windows application that supports a TWAIN interface (such as Adobe® PageMaker®). Some applications allow multiple page scans, while others do not. If you are unsure whether your Windows application supports this feature, refer to your user documentation for the application. The following instructions summarize the procedures for scanning an image.
7 Working With Documents in the Desktop Manager This chapter contains information and instructions for managing, manipulating, and modifying your documents in the MultiPASS Desktop Manager.
Selecting Documents in the Desktop Manager SEL_DOC2.TIF To work with a document, you select it in the open folder. To select a document in Document View, simply click the document thumbnail. To select more than one document, hold the Ctrl key while you click on each document you want to select. SEL_DOC To select a document in List View, simply click the document name in the list. Printing a Document in the Desktop Manager You can print a document from any folder in the Desktop Manager.
2 ❍ A copy of the document to be printed is sent to the Out Box folder. The job is assigned a unique name. When printing is complete, the copy is automatically deleted from the Out Box folder. N Documents in Desktop Manager PRNT.DTM In the Print dialog box, specify the number of copies and click OK. Annotations will not be printed. To print a document with annotations, you must print from the Viewer. See page 7-14 for details on Annotating a Document.
Each job in the Out Box folder displays with a system-assigned name. A job remains in the Out Box folder until it is successfully processed or deleted. You cannot rename a job in the Out Box folder, or move the job to another folder. You can select a job in the list to review information about that job in the status bar. This information includes the name of the original document from which the job came, as well as the reason the job failed (if it did).
A PC fax job receives the Retry status if: • The MultiPASS L6000 is busy with another task, and thus unable to transmit the PC fax, or • The receiving fax line is busy. ❍ On Hold A held job is a PC fax you chose to place on hold, rather than send immediately. The held fax job remains in the Out Box folder until you choose to send or delete it. You can print a job that is on hold. ❍ Failed A job receives a Failed status because a PC fax could not be sent successfully.
Stopping an Active Job If necessary, you can stop the active job from processing. When you do so, the Desktop Manager retains the job in the Out Box folder as a stopped job. You can later reprocess or delete the job. To stop an active job, open the Out Box folder and click Stop on the Edit menu or toolbar.
Creating a Folder To better organize your documents in the MultiPASS Desktop Manager, you can create additional folders. When you create a new folder, you assign a unique name. CREATNEW 1 Documents in Desktop Manager From the File menu, click New Folder. 2 Name the folder. ❍ In the Create Folder dialog box, enter the desired name of your new folder and click OK.
Renaming a Document or Folder You can rename a user-defined folder or a document at any time. Folder names must be unique within the Desktop Manager. Document names must be unique within a folder. Whenever you attempt to rename a folder or document, the system verifies whether the new name is unique. In the event of a conflict, the system alerts you of the conflict. A folder or document name can contain blank spaces. NEWNAME ❍ To rename a document, click the document. Then, on the File menu, click Rename.
Emptying the Trash Folder If you moved documents to the Trash folder, the documents remain in the folder until you move them again to a user-defined folder, delete them individually, or empty the Trash folder. As you move more documents to the Trash folder, more space is used on your hard disk for storing the documents. To prevent out-of-date documents from unnecessarily using space on your disk, you should periodically review your Trash folder and remove the documents no longer needed.
Exporting a Document You can export a document in the Desktop Manager, saving it to a drive and directory you specify. When you export a document, you save a copy of the original document. You can save the document in monochrome TIFF file format. To export a document: 1. Open the folder with the document you want to export. 2. Drag the document to the Export Tiff File button on the command bar. OR Click the document you want to export and, on the File menu, click Export Tiff. EXPORT.TIF 3.
Manipulating a Document in Document View If you are using Document View, you can manipulate the documents in the open folder in a variety of ways. (The only exception is the Out Box folder.) You can arrange the documents in a preferred order. You can also remove a page from a document, split a single document, or merge one document with another. A document thumbnail in Document View retains its position until you rearrange it.
To scroll the pages in a document: ❍ Click the left and right scroll arrows displayed with the page numbers for the document. DRAG_BOX ❍ Drag the scroll tab on the right side of the document. SCROLL TAB Removing a Page from a Document You can remove the current top page of a document. For example, you may want to remove the cover page from a received fax. 1. Scroll through the document until the page you want to remove is on top. 2. Click Remove Page on the Edit menu or toolbar.
To split a document: 1. Scroll to the page where you want to split the document. The top page represents the first page for the newly created document. Documents in Desktop Manager 2. Click Split on the Edit menu or toolbar. Merging a Document You merge two documents to combine them into a single document. The documents are merged in the order you select them. In other words, the first document selected becomes the top pages of the second document selected.
Annotating a Document You can open a document to view its contents, and annotate it with notes, highlighting, stamps, or graphics (line/arrow, rectangle, circle). Although you can save the document with your annotations, any annotations you make are only added markings placed on the original document. The original contents of the document remain intact. If you choose to fax or print the modified document, you have the option not to include the annotations with the document.
1 Open the document in the Document Viewer. ❍ Double-click the document. ❍ Select the document you want to open. On the File menu, click Open Document. ❍ Drag the document to the Open Document button on the toolbar. Annotate the document. ❍ With the document open in the Document Viewer, adjust the size of your view of the document as needed. ❍ Create the desired annotations on your document. ❍ On the File menu, click Save to save the annotations with your document in the Desktop Manager.
Features of the Document Viewer Window ❍ Menu Bar The menu bar contains commands that enable you to perform various tasks with your document. Some of the commands can also be accessed by their corresponding buttons on the toolbar. ❍ Toolbar The toolbar provides you quick access to performing certain Document Viewer tasks. In circumstances where a task is not possible, the toolbar button is unavailable, appearing dimmed.
In addition to the buttons, the toolbar also provides you with a dropdown list box that enables you to select a display size for your document. ❍ Annotation Panel The annotation panel is a set of tools for annotating your open document. When you select a tool on the panel, an additional panel may open enabling you to specify specific features for the tool. You can move the panel around the window to position it for working on your document. You can also hide the display of the panel.
Adjusting Your View of the Document You can adjust your view of the open document in a number of ways, to provide a more workable display area for making annotations. For example, you can hide or show the different components of the Document Viewer. To show/hide the components of the window: ❍ On the View menu, click Toolbar, Status Bar, Annotation Panel, and/or Page Panel. Clicking the same command turns the display of the item on and off.
To enlarge or reduce the size: ❍ To enlarge the document by increments, click Zoom In on the View menu or the toolbar. ❍ To reduce the size of the document by increments, click Zoom Out on the View menu or the toolbar. Adjusting the Image Display For ease of viewing and better visibility, you can adjust or invert the light and dark levels of your displayed document. When you invert the display colors, you change the black areas to white and vice versa.
Paging Through Your Document For multipage documents, you can move to the next or previous page, or a particular page you specify. To page through your document: ❍ Click Next Page or Previous Page on the View menu or toolbar. GOTOPAGE ❍ On the View menu, click Go to Page. On the Go To Page dialog box, enter the page number you want to display and click OK. ❍ Click the page on the Page Panel.
You can type any text that you want for the note, editing the note later if necessary. If you select a font, font size, or special effect, it affects the entire note. If you change any of the attributes while editing a note, or while the note is selected, it changes all the text in the note. If you switch away from the note to do something else (such as change the text size or switch to a different tool) before entering your text, the sticky note is removed.
Concealing a Region You can conceal a region of your document to hide certain areas. For example, you can hide a paragraph before you fax the document to a business contact. You can conceal the paragraph with either an opaque whiteout or blackout annotation, which is always a rectangle. Once applied, the whiteout or blackout annotation can be moved, resized, or deleted. To conceal a region: ❍ On the annotation panel, click the White Out tool.
To insert a Stamp: 2. In the Choose Stamp dialog box, select the desired stamp from the list box and click Accept. Documents in Desktop Manager STAMP 1. On the annotation panel, click the stamp tool. You see this dialog box: 3. Click the cursor in the desired location for placing the stamp. The stamp is placed at that location. Highlighting Your Document You can add a color highlight to the text or other images in your document.
the highlight region. A dotted line displays to show you where the highlight region will be placed. When you release the mouse button, the highlight is created. Creating a Drawing Graphic You can annotate your document with one or more drawing objects that include a straight line, single- and double-headed arrow, hollow rectangle, and a hollow circle or ellipse. When you draw the object, you can select the color and width of the line for the object. To create a drawing object: VWDRAW1/2 1.
Revising Your Annotations Once you have created annotations in your document, you can revise the annotations as needed. For example, you may want to resize, move, delete or cut, or copy and paste an annotation. Selecting One or More Annotations ❍ To select a single annotation, click the Annotation Select button on the annotation panel. Then click the annotation. ❍ To select all annotations, click Select All on the Edit menu. This method selects all the annotations in the open document on all pages.
❍ To change the layered position of an annotation, select the annotation and do one of the following: • To bring the annotation to the foreground, click Bring to Front on the Edit menu. • To place the annotation on the background, click Send to Back on the Edit menu. Resizing the Annotation When you create an annotation, you draw it to the desired size. If the original size proves unsuitable, you can resize the annotation either smaller or larger.
Saving All or Part of a Base Page of Your Document You can select the original base page, or a region of the page, and save the selection to a bitmap (.BMP) file. Once it is saved as a bitmap file, you can import the file into another Windows application as needed. 2. Click Copy on the Edit menu or toolbar. 3. Once copied, on the Edit menu, click Paste to File. 4. When prompted, specify the drive, directory, and name of the file for saving.
Removing an Annotation If you decide you no longer want an annotation to appear in your document, you can remove the annotation, either permanently or by moving it to the clipboard. To remove an annotation, select the annotation and do one of the following: ❍ To delete the annotation permanently, press the Delete key. ❍ To remove the annotation to the clipboard, click Cut on Edit menu or toolbar.
Adjusting the Document Viewer Default Options As you work in the Document Viewer, you can change the options that affect your view of the open document, such as the size and lightness or darkness of the image. However, if you have view settings that you generally prefer to use in most situations, you can define default settings. These settings are activated when you first open the Document Viewer. To adjust the initial Document Viewer options: 2.
Setup and Other Utilities in the 8 Desktop Manager This chapter contains information and instructions on changing your MultiPASS L6000 Setup Options in the Desktop Manager, and using other Desktop Manager utilities.
Setting Up MultiPASS L6000 Options in the Desktop Manager The Desktop Manager contains Setup Options that define the operation of your MultiPASS. When you first install the Desktop Manager, the Setup Options are set to default settings that enable you to begin using your MultiPASS with the Desktop Manager immediately. However, you can change the option settings as needed. To change Setup Options in the Desktop Manager: 1. From the Setup menu, click the group of Setup Options you want to change. 2.
❍ Date Format and Display Language Select the format in which you want to enter the date and the language you want to see in the Desktop Manager screens. ❍ Document Deletion Select this option if you want to be prompted each time you delete a document from the Desktop Manager. ❍ Telephone Select this option if you have attached a telephone to your MultiPASS. With this option selected, you can use the Desktop Manager to dial a phone number.
NEW_SENDTOP.TIF Setting Up Send Fax Options ❍ Fax Information You specify the information that displays as the header for a PC fax: your name, company name, and your fax number. Initially, this information was set up when you installed the Desktop Manager. ❍ Phone Line You specify the dialing method the MultiPASS will use: touch-tone or rotary pulse. You also specify any prefix used to access an outside phone line. Initially, this information was set up when you installed the Desktop Manager.
Restoring the Default Settings If, after making changes, you decide to restore the default settings for the options, click the Use Defaults button. Setting Up Advanced Send Fax Options ❍ Speed You set the transmission speed used to send faxes. The higher the setting, the faster the transmission. If you experience problems when sending faxes, try a lower speed setting. ❍ Pause Duration You set the length of the pause that will be inserted when you enter a pause in a phone number (1-15 seconds).
❍ Auto Start Send When you select this option, the MultiPASS starts scanning automatically five or ten seconds after you enter a phone number. When you don’t select this option, you must press START/COPY to scan the document, or the unit returns to standby mode after 60 seconds. ❍ Off Hook Alarm You select this option to turn on the alarm if the telephone’s handset is off hook. ❍ Image You select a contrast setting that determines the level of contrast in the faxes you send.
❍ Paper Size and Reduction You specify the size of paper in the sheet feeder and whether you want an incoming fax reduced (approximately 98%) to ensure the contents fit on the paper on which it is printed. ❍ Answer You specify the Receive Mode. Initially, you set the Receive Mode when you installed the Desktop Manager. You use the Silent Receive option to specify whether the optional telephone should ring when you receive a call.
❍ Receive Conditions You specify how the system should handle an incoming fax under the following conditions: • When your computer is turned off: You set the MultiPASS to print the fax or save the fax in its memory. • When your computer is turned on: You set the MultiPASS to move (upload) the fax to the Desktop Manager on your computer, or to print the fax.
❍ Speed You set the transmission speed used to receive faxes. The higher the setting, the faster the fax is received. If you experience problems when receiving faxes, try a lower speed setting. ❍ Error Correction (ECM) You select this option to reduce system and line errors when receiving a fax. With this option selected, the system checks each incoming fax for lost data.
• Default Action if No Answer to Telephone You set this option to Receive if you want the MultiPASS to handle an incoming call, detected as a telephone call that is not answered, as an incoming fax. If no fax is received, the line is then disconnected. If you set this option to Disconnect, the MultiPASS automatically disconnects the unanswered call without switching to try and receive a fax.
On the Speed Dial tab, you can set up fax numbers for speed dialing with the MultiPASS. You use the fax recipients set up in your Address Book, and assign the desired individual recipients to speed dial codes. If the recipient has not yet been set up in the Address Book, you can add the recipient while creating speed dial assignments. You can also set up a group speed dial by assigning two or more individual speed dial assignments to a single speed dial assignment.
Making a Phone Call From the Desktop Manager You can use the MultiPASS and Desktop Manager to dial telephone calls if: ❍ You have a telephone attached to the MultiPASS. ❍ You enabled the Telephone Attached to Unit option on the Preferences tab in the Setup Options dialog box in the Desktop Manager. (See page 8-3.) You can place a call to any individual you want, whether or not the individual has been set up in the Address Book.
2 In the Phone dialog box, enter the phone number you want to call. ❍ You can enter the phone number in the Prefix and Phone boxes, or select an Address Book entry. ❍ When you enter the phone number, you use the applicable numeric characters and any valid characters that separate the different segments of the phone number. For example, you can use 0 through 9, dash (-), or parentheses (). Other characters are also available for entering a phone number.
Using the Status Monitor The Status Monitor is a utility that enables you to track the current status of the MultiPASS, incoming and outgoing faxes, print and scan jobs, and any error conditions needing your attention. You can open the Status Monitor either from the Windows desktop or the MultiPASS Desktop Manager. The Status Monitor displays as a button and can also display as a window.
A menu contains commands that enable you to open the Status Monitor window, open the Desktop Manager, and close the Status Monitor. ❍ To open the menu on the minimized Status Monitor, click the right mouse button on the Status Monitor icon or button. ❍ To open the Status Monitor window from the icon or button, click Restore on the Status Monitor menu. ❍ To open the Desktop Manager from the Status Monitor icon or button, click Go to Manager on the Status Monitor menu.
Status Messages The Status Monitor reports the following statuses for the MultiPASS. ❍ Idle The MultiPASS is currently inactive. ❍ Scanning The MultiPASS is scanning an image. The Status Monitor window displays the number of the page currently being scanned. ❍ Printing The MultiPASS is printing a document. The Status Monitor window displays the number of the page currently being printed. ❍ Sending Fax The MultiPASS is sending a fax document.
Closing the MultiPASS Background The MultiPASS Background is a utility that monitors and controls activity between your computer and your MultiPASS, including: ❍ Input and output (such as sent and received faxes) to and from the Desktop Manager ❍ Output (print and PC fax activity) from Windows applications. When you installed the Desktop Manager, the MultiPASS Background was placed in the Windows StartUp group and is automatically opened when you open Windows.
Removing MultiPASS Background From StartUp CFXINIT Closing the MultiPASS Background does not remove it from the Windows StartUp group. If you have disconnected your MultiPASS, the next time you start Windows, the MultiPASS Background will try to open. At that time, the MultiPASS Background will be unable to detect the device, displaying an error message. Click OK to close the message dialog box. The MultiPASS Background closes automatically, since it cannot detect the MultiPASS device.
Restarting the MultiPASS Background If you reconnect the MultiPASS to the port and want to begin using the Desktop Manager again, the MultiPASS Background is restarted automatically when you open the Desktop Manager. You can also open the MultiPASS Background without opening the Desktop Manager. To restart the MultiPASS Background: 1. On the Windows desktop, click Start and then point to Programs. 2. On the Programs menu, point to Canon MultiPASS L6000. Then click MultiPASS Background.
Disconnecting the MultiPASS You can disconnect the MultiPASS if you want to use the parallel port for another purpose. Before disconnecting your unit, be sure to close the MultiPASS Background. 1. Turn off your computer. 2. Unplug your computer from all electrical sources. 3. Unplug the MultiPASS from all electrical sources. 4. On the back of your computer, remove the cable connector from the parallel printer port. 5. On the MultiPASS, release the wire clips and remove the cable connector from the port. 6.
2. When prompted in a dialog box, click Yes to view the log file. 3. In the MultiPASS Diagnostics window, to save the log file, choose Save As on the File menu. 4. In the Save As dialog box, specify the drive, directory, and filename for saving the file. Then click OK. 5. To exit the MultiPASS Diagnostics window, click Exit on the File menu.
❍ To remove the printer driver: 1. On the Windows desktop, click Start, and then point to Settings. 2. On the Settings menu, click Printers. 3. In the Printers dialog box, click the Canon MultiPASS L6000 Printer icon and press the Delete key. Repeat this step for the Canon MultiPASS L6000 Fax icon.
Maintaining the 9 MultiPASS L6000 This chapter describes the routine maintenance required for your MultiPASS L6000. It includes: ❍ MultiPASS L6000 guidelines ❍ Routine maintenance ❍ Cleaning inside the MultiPASS ❍ Cleaning the scanner components ❍ Toner cartridge guidelines ❍ Replacing the toner cartridge ❍ Transporting the MultiPASS MultiPASS L6000 Guidelines ❍ Place the MultiPASS on a stable surface. Do not use an angled stand. Avoid setting the unit in direct sunlight.
❍ Never pull on the cord to unplug the MultiPASS. Pull on the plug itself. ❍ Do not overload the electrical outlet where the MultiPASS is plugged in. ❍ For your safety, unplug the MultiPASS during electrical storms. MP_L6000 ❍ Lift the MultiPASS from the bottom only. Do not lift the unit by the operator panel, front cover, or any of its trays. GRIP HERE Routine Maintenance Your MultiPASS requires little routine maintenance.
Cleaning Inside the MultiPASS To prevent toner powder and paper dust from accumulating and affecting the unit’s print quality, clean the inside of the MultiPASS periodically. N When you unplug the unit, any faxes stored in memory will be erased. Be sure to print out any documents stored in memory before unplugging the unit. See Printing Documents Received in Memory on page 5-5. 1 ❍ Open the front cover by pressing the release latches on the sides of the unit.
2 ❍ Hold the cartridge by its handle and remove it. REM_CRT Remove the toner cartridge. HANDLE ❍ Store the cartridge in its protective bag to avoid exposure to light. Use a clean, soft, dry, lint-free cloth to remove any toner or paper debris from the shaded area. C 9-4 REM_DEBRIS 3 TRANSFER CHARGING ROLLER (BLACK) Do not touch the transfer charging roller (black) at the back, as this may affect the print quality of your faxes.
4 ❍ Gently press the cartridge into the unit as far as it will go. Press down and back on the cartridge’s handle. REPL_CART When you have finished cleaning the MultiPASS, replace the toner cartridge. 5 ❍ Plug the unit back in. Chapter 9 MP L6000—USERS MANUAL/V000/12-97 Maintaining the MultiPASS L6000 9-5 CLOSE_CVR ❍ Use both hands to lift the cover back into the closed position. Maintaining the MultiPASS L6000 Close the front cover.
Cleaning the Scanner Components Periodically check the scanning glass and rollers. N When you unplug the unit, any faxes stored in memory will be erased. Be sure to print out any documents received in memory before unplugging the unit. See Printing Documents Received in Memory on page 5-5. 1 OPEN_OPPNL Unplug the MultiPASS and open the operator panel. 2 ❍ If the document scanning glass and rollers are dirty, the documents you send or print will also be dirty.
3 ❍ Dirt and dust particles that collect on the underside of the operator panel also affect the quality of documents you copy and send. CLN_SHD_OP Clean the shaded areas of the operator panel and the unit. 4 Chapter 9 MP L6000—USERS MANUAL/V000/12-97 Maintaining the MultiPASS L6000 9-7 CLN_ROLLS Maintaining the MultiPASS L6000 Use a soft, dry clean cloth to wipe up paper dust around the rollers.
5 N CLOSE_OPPNL When you are finished, close the operator panel by pressing it down from the center. Be sure to close the operator panel until it locks into place. Otherwise the unit will not function properly. ❍ Plug the MultiPASS back in. Toner Cartridge Guidelines FX-3 The FX-3 Toner Cartridge contains a photosensitive component called the drum and black carbon powder called toner. The drum is extremely light sensitive and may deteriorate if exposed to light.
When storing toner cartridges, follow these guidelines: ❍ Store cartridges in their protective bags. Do not open a protective bag until you are ready to install the cartridge in the MultiPASS. ❍ Store cartridges where they will not be exposed to direct sunlight. ❍ Store cartridges right side up—not on their ends or upside down. This helps prevent the toner particles from settling to one side of the cartridge, which may cause streaks or lines on your printed pages.
Canon instituted the Clean Earth Campaign to recycle used cartridges. To participate in this program, simply follow the instructions packed with your new FX-3 Toner Cartridge. Canon encourages you to return used cartridges to us at no cost to you. For more information about the Canon Clean Earth Campaign, you can call 1-800-962-2708 in the continental United States.
Replacing the Toner Cartridge The actual amount of toner that you use will vary depending on the print density of a page. If the majority of your output is graphics, you may need to change cartridges more often than when you are printing text only. See Appendix A, Specifications, for details on the life expectancy of the toner cartridge. Preparing the Toner Cartridge 1 Remove the new FX-3 Toner Cartridge from its protective bag. ❍ Save the protective bag; you may need to repack the cartridge later.
3 ❍ Place the cartridge on a flat, clean surface, and steady it with one hand. ❍ Remove the seal by gently pulling on the plastic tab with your other hand. TONER_CART_3 TONER_CART_2 ❍ Use a firm even pull to remove the plastic seal. To avoid breaking the seal, do not jerk on it unevenly.
Inserting the Cartridge 1 ❍ Press the release latches on the sides of the unit. ❍ Lift the cover forward to its open position. OPEN_CVR Open the front cover. 2 ❍ Dispose of the toner cartridge properly. To recycle your used cartridge, follow the instructions included with your new FX-3 Toner Cartridge. Chapter 9 MP L6000—USERS MANUAL/V000/12-97 Maintaining the MultiPASS L6000 9-13 CART_DOWN2 Maintaining the MultiPASS L6000 Remove the old cartridge.
3 Insert the new toner cartridge into the unit. ❍ Align the rails on the left and right sides of the cartridge with the guides inside the unit. ❍ Slide the unit into position. CART_IN ❍ Always hold the cartridge by its handle when inserting it in the unit. 4 ❍ Press down and back on the cartridge’s handle. CART_DOWN Gently press the cartridge into the unit as far as it will go.
5 CLOSE_CVR Close the front cover. Transporting the MultiPASS If you need to transport the MultiPASS, be very careful. 1 Disconnect all cables. ❍ Unplug the power cord. ❍ Disconnect the telephone lines and parallel cable. Remove any paper. ❍ Remove any paper from the multi-purpose tray or manual feed slot. ❍ Remove any document from the ADF. 3 Remove the toner cartridge. ❍ Open the front cover and remove the toner cartridge.
4 Remove all trays. ❍ Remove the paper rest. ❍ Remove the support trays. ❍ Close the output tray and extension. 5 Pack the unit. ❍ Replace all shipping tape and shipping materials. ❍ Carefully pack the unit in its original packing materials. N 9-16 If you no longer have the shipping carton your MultiPASS came in, pack the unit in a suitably sized, sturdy cardboard box, using bubble wrap, foam peanuts, or other suitable packing materials.
Troubleshooting 1 This chapter contains information to help you solve problems you may have when using the MultiPASS L6000.
If you need to contact Canon directly, make sure you have the following information: ❍ Product name—MultiPASS L6000 ❍ Serial number ❍ MultiPASS Desktop Manager version number ❍ Place of purchase ❍ Nature of problem ❍ Steps you have taken to solve the problem and the results The serial number is located on the label on the back of the unit: NO. RS5-8658 MADE IN JAPAN A250_7-01 CANON INC.(DA1) XXXXXXXX SERIAL NUMBER The version number of MultiPASS Desktop Manager is included in the About information.
Paper Jams On occasion, the document feeding into the MultiPASS or the paper in its multi-purpose tray may misfeed or jam. You can usually clear the problem easily. N You need not unplug the MultiPASS to clear paper jams. Jams in the Automatic Document Feeder (ADF) CHECK DOCUMENT 1 Press STOP. Stops the operation. 2 ❍ Gently pull the operator panel toward you. N Do not try to pull out the document without opening the operator panel; you may tear or smudge the document.
3 ❍ Pull the jammed page in either direction, but DO NOT force it. ADF_JAM Remove the document. ❍ If a multipage document is loaded, remove the entire document from the ADF. 4 ❍ Gently press the operator panel until it clicks closed. PANEL_CLOSE Close the operator panel. ❍ Fan and stack the sheets, and replace the stack in the ADF. ❍ Press STOP to clear the error message. ❍ Start your operation again.
Jams in the Output Slots CLEAR PAPER JAM 1 JAM_REMOVE Gently pull any jammed paper out of the unit. FACEDOWN OUTPUT SLOT FACEUP OUTPUT SLOT 2 Remove the stack of paper from the multipurpose tray. ❍ Fan the paper, and tap it on a flat surface to even out the stack. ❍ Reload the paper into the multi-purpose tray. Make sure you adjust the paper guide to the stack, and that the stack does not exceed the limit mark.
Jams Inside the Unit C ❍ The fixing assembly (shaded) becomes extremely hot when the MultiPASS is in use. Be very careful not to touch it, as injury may result. FIXING_ASSY_2 ❍ When removing the jammed paper, be careful not to touch the transfer charging roller, as its surface is very delicate and susceptible to finger oil and scratches, which may lead to print deterioration. TRANSFER CHARGING ROLLER 1 ❍ Press the release latches on the sides of the unit. ❍ Lift the cover forward to its open position.
2 Remove the toner cartridge. ❍ Hold the cartridge by its handle and remove it from the unit. CVR_LIGHT ❍ Cover the cartridge to protect it from the light. 3 PRESS_PPR_REL Press the paper release lever toward the back of the unit. Troubleshooting Now locate the jammed piece of paper.
Jams in the Back Area of the Unit If the paper has jammed near the multi-purpose tray slot: MULTI_JAM ❍ Hold the unit steady and pull the jammed paper straight out from the unit. N ❍ If the jammed sheet tears, remove all of the paper scraps from the unit. ❍ Be careful not to spill the toner on the jammed sheet. The toner is not fused to the paper yet, and any toner spilled inside the unit may adversely affect print quality. ❍ Be careful not to get toner on your hands or clothing.
Jams in the Front Area of the Unit If the top edge of the paper has passed through the fixing assembly: JAMS_1 ❍ Pass the paper under the roller. ❍ Use both hands to carefully pull the jammed paper. ❍ Pull gently being careful not to tear the paper. Make sure no paper remains inside the unit. Troubleshooting JAMS_2 ❍ Be sure to remove all the jammed paper. Any remaining paper will cause more jams.
If the paper is jammed near the faceup delivery slot: JAMS_3 ❍ Hold the front cover and gently pull the sheet through the exit slot. N Do not close the front cover while removing a jammed sheet of paper. This will return the paper release lever to its closed position. After Clearing a Paper Jam After removing the jammed paper, follow these steps: 1. Install the FX-3 Toner Cartridge back in the unit. 2. Move the paper release lever back to its original position (toward the front). 3.
LCD Messages Message Error Code Cause Action AUTO REDIAL — The MultiPASS is waiting to redial the other party’s number because the line was busy or the other party did not answer when you tried to send the document. Wait for the MultiPASS to try redialing. If that doesn’t work, wait until the MultiPASS starts to dial the number, then press STOP to cancel redialing. Try to send the document again at a later time. BUSY/NO SIGNAL #005/018 The telephone number you dialed is busy.
Message Error Code Cause Action CHANGE CARTRIDGE — The toner cartridge may be empty. Rock the cartridge to distribute the toner inside (see page 9-11). If necessary, replace the toner cartridge. Any documents received in memory will be printed automatically. Replace the toner cartridge and have the other party send the fax again. Make sure the toner cartridge is installed properly. Close the front cover. Remove the document you are trying to send or copy and start again.
Message Error Code Cause Action COMMUNICATING PLEASE WAIT — Wait until the fax is sent, or use memory sending. DOC TOO LONG #003 You tried to send a fax manually when the MultiPASS was already sending a fax from memory. It took more than 32 minutes to send or copy a document. It took more than 32 minutes to receive a document.
Message MEMORY USED nn% Error Code Cause — Shows the percentage of If you need more space, memory currently in use. print or send any documents in memory. The receiving fax Make sure you dialed machine does not the correct number. answer. Try again later. The other party’s fax is Contact the other party out of paper or its and have them install memory is full. paper in their fax. The one-touch or coded Register the number speed dialing number (see page 3-18). has not been registered.
Printing Problems Problem Cause Solution The ALARM light comes on and the MultiPASS L6000 beeps while printing The MultiPASS may have a paper jam. Clear any paper jams. See page 10-3. Data from computer is not printed The power cord may not be plugged in securely. If you cannot clear the problem, unplug the MultiPASS, wait 15 seconds, then plug it in again. (You will lose any documents stored in memory.
Problem Cause Solution Data from computer is not printed (continued) The MultiPASS L6000 may not be set as the default printer or the selected printer. Make sure the MultiPASS L6000 is selected as the default or current printer. Make sure MultiPASS Background is running. Make sure the MultiPASS Printer Driver is configured to use the computer’s parallel port. See page 2-5. Make sure your computer’s CMOS has the primary parallel port set to LPT1.
Problem Cause Solution Printout does not match paper size Paper may not be loaded and aligned correctly in the multi-purpose tray. Make sure the paper is loaded and aligned correctly. See page 1-9. The application’s page size and margin settings may be incorrect. Make sure the paper size and margin set in your application are correct for the paper in the multi-purpose tray. The selected printer driver may be incorrect. Make sure you select the MultiPASS printer in your application.
Print Quality Problems Problem Cause Solution Print is not clear The paper you are using may not be supported by the unit. Make sure you are using paper that matches the specifications (see page A-1). You may be printing on the wrong side of the paper. Some paper has a right side for printing. If the print quality is not as clear as you would like it to be, try turning the paper over and printing on the other side. Toner may be low or unevenly distributed.
Cause Solution Several sheets load into unit at the same time Paper may not be loaded correctly in the multi-purpose tray. Sheets of paper may be sticking together. Make sure paper is inserted correctly in the multi-purpose tray. Be sure to fan the stack of paper before placing it in the multi-purpose tray. Make sure the paper rest is extended and the paper is stacked correctly in the multi-purpose tray. Do not force the stack into the multi-purpose tray. Load just one type of paper.
Faxing Problems Problem Cause Solution Cannot send a document The MultiPASS may have overheated. Unplug the unit and let it cool for several minutes. Try sending again. The MultiPASS may not be set for the type of telephone line in use (pulse/tone). If you have a pulse line, be sure the MultiPASS is set for pulse dialing. The document may not have been fed correctly into the MultiPASS. Remove the document, stack it, and load it into the ADF correctly (see page 1-12).
Problem Cause Solution Cannot send or receive using Error Correction Mode (ECM) The other party’s fax may not support ECM. Some fax units do not support ECM transmission. If the other party’s fax does not support ECM transmission, then the document is sent in the normal mode without error checking. Errors occur frequently while sending or receiving The phone line may be in poor condition, or you may have a poor connection. Lower the transmission speed.
Problem Cause Solution The MultiPASS does not switch automatically between telephone and fax transmissions The MultiPASS may not be in FaxTel mode. For the MultiPASS to switch automatically between fax and telephone reception, the Receive Mode must be set to FaxTel mode. In the Advanced: Receive Fax options, the “Default Action if No Answer To Telephone” is set to Disconnect. Make sure this option is set to Receive. (See page 8-8). There may be a document in memory.
Problem Cause Solution Print quality is poor You may not be using the correct type of paper. Be sure you are using paper that meets the paper requirements for the MultiPASS (see page A-1). Make a copy on your MultiPASS. If the image is OK, then your MultiPASS is operating properly. Contact the other party and have them check their machine. Make sure Error correction (ECM) is set to on in the Advanced: Receive fax dialog box of the Desktop Manager. The sending party may be having a problem.
Telephone Problems Problem Cause Solution You cannot dial The telephone line may not be connected properly. Be sure the telephone line is correctly connected to the MultiPASS (see your Quick Start Guide). The unit may not be getting power. Make sure the power cord is connected to the MultiPASS and to an AC outlet; make sure the AC outlet has power. If you have a pulse line, be sure the MultiPASS is set for pulse dialing (see page 8-4).
Problem Cause Solution MEMORY FULL The MultiPASS’s memory is full. Print out any faxes stored in memory. Then print one copy at a time. The documents you are trying to print may have too much graphic or detailed information. If nothing is stored in memory, print one copy at a time. appears in the LCD when you are making multiple copies General Problems Problem Cause Solution The MultiPASS has no power The power cord may not be securely plugged into the unit.
Technical Notes Using Other Bi-directional Devices If you have another bi-directional device (such as a Windows Printing System printer or a later-model laser printer) installed on your computer and you are attempting to use the same port on which you have the MultiPASS connected, you may experience undesirable results when printing a document. Be sure the MultiPASS is the only device configured to a particular port. The MultiPASS operates properly only with a dedicated parallel port.
Using Switch Boxes Canon does not recommend using a switch box with the MultiPASS. To use more than one printer, it’s a good idea to add a second parallel port to your computer. If the Power Goes Out If power to the MultiPASS L6000 is cut off, any documents stored in its fax memory will be lost. (The MultiPASS automatically prints a list of the lost documents when power is restored.) Because of this, be sure to print documents stored in memory or resend them as soon as possible.
N 10-28 If there is no paper in the multi-purpose tray when the power goes out, the LCD will display LOAD PAPER and PRINTING REPORT when the power is restored. If this happens, load paper in the multi-purpose tray and wait for the unit to print the Memory Clear Report. You will be unable to send documents or receive faxes in memory until you do this. If you have no paper available and you urgently need to send a document or receive a fax in memory, press the STOP button to enable sending and receiving.
Specifications Specifications A Laser Printer Printing method Laser beam printing Printing resolution 300 × 300 dpi (default) 600 × 600 dpi Paper handling Automatic feed Manual feed Multi-purpose tray capacity Plain paper (20 lb or 75 g/m2) Envelopes Paper size Letter Legal A4 U.S. Commercial number 10 envelope European DL envelope Approx. 100 sheets 7 envelopes (U.S. Commercial number 10 or European DL) 8.5 in × 11 in 8.5 in × 14 in 210 mm × 297 mm 9.5 in × 4.
Printable areaÑPapers a b c e Letter size Legal size a b c d e f a b c d e f 8.5 in 0.16 in (max) 0.20 in (max) 11.0 in 0.22 in (max) 0.40 in (max) 8.5 in 0.16 in (max) 0.20 in (max) 14.0 in 0.22 in (max) 0.42 in (max) d A4 size a b c d e f f A250_A_01 The shaded portion in the following figure shows the printing area for papers. 210 mm 4.0 mm (max) 5.0 mm (max) 297 mm 5.5 mm (max) 10.1 mm (max) Printable areaÑEnvelopes a c U.S. Commercial number 10 a 4.1 in b 9.5 in c 0.
Toner Cartridge FX-3 Toner Cartridge Approx. 2700 pages/cartridge at 4% paper coverage Specifications Cartridge yield Facsimile Applicable line Public switched telephone network Compatibility G3 Data compression system MH, MR, MMR (ECM-MMR) Modem type Fax modem Modem speed 14400/9600/7200/4800/2400 bps Automatic fallback Transmission speed Approx. 6 seconds/page* at 14.4 Kbps, G3 ECM-MMR transmitting from memory Transmission/reception memory Approx. 1.4 MB DRAM, MR storage Approx.
Fax resolution Fine mode—203 pels/in × 196 lines/in (8 pels/mm × 7.7 lines/mm) Standard mode—203 pels/in × 98 lines/in (8 pels/mm × 3.
Copier Scanning resolution Specifications 600 × 300 dpi (Direct copy) 300 × 300 dpi (Memory copy) Printing resolution 600 × 600 dpi Default size 100% Reduction sizes 70%, 80%, 90% Copy speed One copy only—25 seconds First copy of multiple copies—45 seconds Subsequent copies—10 seconds Multiple copies Up to 99 copies of a document Scanner Scanning method Solid-state electronic scanning by contact image sensor Scanning image processing UHQ™ (Ultra High Quality image enhancement) Halftones—256 levels
Scanning resolution 200 × 200 dpi, 300 × 300 dpi, and 600 × 600 dpi Effective scanning width 8.42 in (214 mm) Compatibility TWAIN Scanning speed B&W Text mode—8.7 sec/page (300 × 300 dpi) 17.5 sec/page (600 × 600 dpi) Grayscale mode—35 sec/page (300 × 300 dpi) 70 sec/page (600 × 600 dpi) Document sizes (W × L) Maximum—Auto feed—8.5 × 14 in (216 × 355.9 mm) Maximum—Manual feed—8.5 × 39 in (216 × 1 mm) Minimum—Auto feed—4.1 × 5.8 in (105 × 148 mm) Minimum—Manual feed—3.5 × 1.75 in (88.9 × 44.
Scanned image Specifications The actual scanned image size for the MultiPASS is shown below. This information applies to documents that will be scanned for faxing or copying. 0.16 in (4.0 mm) 8.42 in 0.12 in (214 mm) (3.0 mm) PAPER SIZE Legal/Letter 0.16 in (4.0 mm) 0.12 in (3.0 mm) There is a 0.12 in (3.0 mm) margin on either side of the sheet and a 0.16 in (4.0 mm) margin on the top and bottom that are outside the scanning area.
General Specifications Power Source 120V/60Hz Power Consumption Approx. 620W (Maximum) Approx. 7W (Standby) Dimension (W x D x H) 144 in × 14.4 in × 9.5 in (365 mm × 365 mm × 242 mm) Main unit – no trays Weight 19.0 lb (8.6 kg) Environmental Conditions Temperature: 50° F - 90.5° F (10° C - 32.
Space Requirements 27.0” (685 mm) TOP VIEW 14.3” (365 mm) Specifications 14.3” (365 mm) 15.3” (390 mm) 9.
Receiving Faxes and Phone Calls AutomaticallyÑFaxTel Mode In FaxTel mode, the MultiPASS monitors all incoming calls to see whether the call is from another fax machine or from a telephone: Type of call Telephone Telephone charges begin for caller.
Using the MultiPASS L6000 B as a Stand-alone Fax Stand-alone Fax If you plan to use the MultiPASS as a stand-alone fax, and you do not install the MultiPASS Desktop Manager, you must enter your name and fax number from the operator panel. If you choose to use the MultiPASS this way, you will not be able to use its many features, such as speed dialing, PC faxing, or scanning. Canon recommends that you install the MultiPASS software as described in the Quick Start Guide.
Entering Information in the MultiPASS When using the MultiPASS as a stand-alone fax machine, you must enter your user information into the unit through the operator panel. When entering information through the operator panel of the MultiPASS, follow these guidelines. ❍ If you pause and do not make an entry for more than 60 seconds, the MultiPASS returns to Standby mode. You must start the procedure over from the beginning.
1 Press FUNCTION on the one-touch speed dialing keypad. Then press the > button. FUNCTION 1 2 FUNCTION USER SETTINGS Press START/COPY twice. START/COPY DATE & TIME START/COPY 06/08/97 Stand-alone Fax 2 15:36 3 Enter todayÕs date and the time using the numeric buttons. ❍ Use the month-day-year format (mm/dd/yy). ❍ Precede single digits with a zero.
❍ Set the time using the 24-hour clock system. ❍ Example: 07:30 = 7:30 A.M. 17:05 = 5:05 P.M. ABC 1 GHI 4 PRS 7 DEF 2 JKL 3 MNO 5 TUV 6 WXY 8 11/15/97 08:15 9 SYMBOLS OPER 0 TONE 4 Press START/COPY twice when the date and time are entered. START/COPY DATA ENTRY OK START/COPY TEL = 5 Enter your fax number (up to 20 digits) using the numeric buttons.
6 Press START/COPY when the fax number is entered. START/COPY DATA ENTRY OK ❍ After a few seconds, the LCD display changes to: UNIT NAME START/COPY Stand-alone Fax Then press START/COPY again. 7 Enter your name (up to 24 characters) using the numeric buttons. ❍ Press the button with the letter you want to enter; for example, press 2 three times to enter a capital C. CANON FAX BACK Button Characters 1 1 2 ABCabc2 3 DEFdef3 4 GHIghi4 5 JKLjk15 6 MNOmno6 7 PQRSpqrs7 8 TUVtuv8 9 WXYZwxyz9 0 0 # -.
8 Press START/COPY when you finish entering your name. START/COPY DATA ENTRY OK 9 Press STOP to complete the registration. B-6 STOP The MultiPASS returns to Standby Mode.
Glossary G Activity report Journal of fax transactions, both sent and received. Address Book The electronic Address Book provided by the MultiPASS Desktop Manager that allows you to create a list of people with their phone and fax numbers. Automatic dialing Dialing fax or telephone numbers by using a shortcut of pressing one to three buttons. To use automatic dialing, you must register the numbers in the MultiPASS Desktop Manager.
CCITT #1 Chart A test chart, defined by CCITT/ITU-TS, used to measure the transmission speed as well as the transmitting and receiving memory capacity of a fax machine. CCITT/ITU-TS Formerly known as CCITT, Consultative Committee for International Telegraph and Telephone. CCITT has been replaced by the International Telecommunications Union-Telecommunications Sector (ITU-TS), a committee created to set international standards for telecommunications.
DRPD Distinctive Ring Pattern Detection. Allows you to assign up to five different ring patterns to distinguish voice and fax calls using your telephone company’s special services. ECM Error Correction Mode. The ability of your MultiPASS to reduce system and line errors when sending or receiving from another fax with ECM capability. ECM is most effective in areas where the telephone lines are in poor condition or there is frequent interference on the line.
Group dialing A dialing method that enables you to dial up to 55 registered one-touch speed dialing or coded speed dialing numbers together as a group. This means that you can press just one to three buttons to enter numbers when sending the same document to many destinations. Halftone Using this method, the MultiPASS produces shades of gray by mapping dots to be printed. IEEE 1284 IEEE 1284 is the new specification standard for computer-to-peripheral bi-directional parallel interface communications.
Memory broadcast Allows you to send a scanned fax to as many as 57 locations at once, using a combination of one-touch speed dialing, coded speed dialing, and regular dialing. Modem A device that converts (Modulates) digital data for transmission over telephone lines. At the receiving end, this device converts the modulated data (DEModulates) to digital format that the computer understands.
PC fax An electronic way to send and receive faxes. A PC fax is sent from or received directly into a computer. Using the MultiPASS Desktop Manager you can send and receive PC faxes, and save, sort, and/or print the PC faxes. Portrait orientation Refers to printing across the width of the page (letter style). This is the opposite of landscape orientation, which is printing across the length of the page.
Registering A process by which you place fax or telephone numbers and names in the MultiPASS’s memory for automatic dialing so that you can save time dialing frequently called destinations. You register numbers using the Address Book in the MultiPASS Desktop Manager. Regular dialing Pressing the individual numeric buttons to dial a fax or telephone number. Remote receiving ID A two-digit code that enables you to manually activate a fax using a telephone that is connected to the MultiPASS.
The rate at which faxes are transmitted through the phone line. See also bps (bits per seconds). STANDARD A document setting for sending normal typewritten or printed documents containing only text and no drawings, photographs, or illustrations. Standby The mode in which the MultiPASS is on and ready to use. All operations start from Standby mode when the LCD displays the date and time.
TX See Sending. Typeface The printed design of characters. For instance, Courier, Script, and Roman typefaces all print characters of different designs. Typestyle Refers to how the typeface appears: slanted (italic) or upright. Glossary UHQ (Ultra High Quality) An exclusive Canon digital image processing system that incorporates 64 shades of gray along with a special edge enhancement feature which ensures that text and photos are transmitted with ultimate clarity.
G-10 MP L6000—USERS MANUAL/V000/12-97 Glossary
Index I A Accessories: 1-2 Active job: 7-4, 7-6 Address Book entries: 3-11–15 exporting: 3-17–18 importing: 3-15–16 setting up: 3-10–18 sorting: 3-12 ADF: 1-5, 1-12, 2-8, 4-2, 6-1, A-3, A-5 document thickness: A-5 document weight: A-5 paper jams: 10-3–4 paper size: A-5 Advanced Receive Fax options: 8-8–10 Send Fax options: 8-5–6 ALARM light: 1-8, 4-4, 10-15 Annotations: 7-14–29 adding: 7-20–24 copying and pasting: 7-26 hiding: 7-24 including: 4-19 moving: 7-25–26 panel: 7-17–18 removing: 7-28 resizing: 7-2
Cartridge: See FX-3 Toner Cartridge CCITT No.
E Economy mode: A-4 Effective scanning width: A-6 E-mail attaching document: 7-10 support, Canon: 1-2 Entering information: B-2–6 Envelopes loading: 2-11–13 printable area: A-2 Environmental conditions: A-8 Error Correction (ECM): 8-5, 8-9 Error status: 7-5, 8-16 Export Tiff: 7-10 Exporting Address Book: 3-17–18 document: 7-10, 7-28 Extension phone: 5-3 Index MP-L6000—USERS MANUAL/V000/12-97 F Facedown delivery: 2-8–10 slot: 1-5 Faceup delivery: 2-8, 2-10, 2-15 slot: 1-5 Facsimile, specifications: A-3–4
FILE PRINT message: 5-8 option: B-1 Fine mode fax: A-4 copy: 6-3 Fine resolution: 4-14–15 Fixing assembly: 1-6, 10-6 Folder(s) creating: 7-7 deleting: 7-8 list: 3-4 Desktop Manager: 3-5–7 renaming: 7-8 Front cover: 1-5–6 FUNCTION button: 1-8, B-3 FX-3 Toner Cartridge: 1-2, 2-8, 9-8–10, A-3 compartment: 1-6 guidelines: 9-8–10 warranty: 9-10 G General problems: 10-25 specifications: A-8 General tab, Windows: 2-5 Graphics, and text mode: 2-6 Graphics tab, Windows: 2-6 Grayscale mode: A-6 scanning: 6-5 Group
M Magnetic fields: 9-1 Main tab, scanning: 6-5 Maintaining, MultiPASS: 9-1–16 Making phone call, Desktop Manager: 8-12–13 Managing documents, Desktop Manager: 7-1–10 Manual mode: 5-3 redialing: 4-7 sending: 4-9 Manual feed slot: 1-5, 2-8, 2-14 Manually feeding paper: 2-14–15 Media type: 2-6, A-1 Memory: A-7 faxes stored: 6-4 printing document: 5-5 sending: 4-2 Memory Clear Report: 10-27–28 MEMORY FULL message: 6-4 Menu bar: 3-3, 4-23 viewer: 7-16 Merging, document: 7-13 Messages, LCD: 10-11–14 Modem speed:
One-touch speed dialing: 4-5 buttons: 1-8 On-line help, Windows 95: 2-4 Opening, Cover Page Designer: 4-22 Operator panel: 1-5, 1-7–8 copying documents: 6-2–4 using: 1-7–8 Optical Character Recognition (OCR) software: 6-6 Out Box: 3-9 folder: 3-6, 7-3–6 Outgoing message: 5-5 Output slots, paper jams: 10-5 Output tray: 1-5 extension: 1-5 P Packing materials: 9-16 Page adding to document: 1-14 orientation: 2-6 panel: 7-17, 7-20 size, scanning: 6-7 Paper feed method: 2-6 feeding problems: 10-18–19 guidelines:
Q Quality, faxes: 4-13–15 Queued job: 7-4 R RAM: A-7 REC’D IN FILE message: 5-6, 5-8 REC’D IN MEMORY message: 5-6 Receive conditions: 8-8 Receive fax, via telephone: 5-3–4 Receive Fax options: 8-7–10 advanced: 8-8–10 Receive Mode: 5-1–5, 5-10, 8-7 RECEIVE MODE button: 1-7 Receiving documents: 5-2–5 fax status: 8-16 Receiving faxes: 5-1–10 computer off: 5-7–8 computer on: 5-7 FaxTel mode: A-10 Desktop Manager: 5-7–8 Receiving telephone calls: 5-2–3 Recording paper: 2-8 REDIAL/PAUSE button: 1-8, 4-3 Rediali
Scanning: 6-1, 6-4–9 documents: 1-11, 6-4–8 enlarging: 6-5 image processing: A-5 message: 8-16 method: A-5 Desktop Manager: 6-4–8 preview: 6-8 reducing: 6-5 resolution: A-5–6 speed: A-6 width: A-6 Windows application: 6-9 Scanning glass: 9-6 Scheduled job: 7-4, 7-6 Scrolling, documents: 7-11–12 Selecting paper delivery: 2-9–10 Send Fax advanced: 8-5–6 defining: 4-18–19 dialog box: 4-17 options: 8-4–6 Sending document: 4-2–10 fax status: 8-16 multiple locations: 4-11–13 PC faxes: 4-16–19 Sending faxes: 4-1–3
T Tape backups: 10-26 Technical notes: 10-26 support: 1-2, 10-1 TEL LINE TYPE: B-1 Telephone answering machine jack: 1-6 calls: 5-2–3 jack: 1-6 option: 8-3 problems: 10-24 receiving fax: 5-3–4 specifications: A-8 Text documents, copying: 6-3 Text Enhanced mode, scanning: 6-5–6 Threshold, scanning: 6-7 Thumbnails, documents: 3-8 TIFF file format: 7-9–10 Tone tab, scanning: 6-6 Toner: 9-8 Toner cartridge: 1-2, 9-4–5, 9-15 guidelines: 9-8–10 inserting: 9-13–15 preparing: 9-11–12 replacing: 9-11–15 specificatio
W Warranty: 1-3, 10-1 FX-3 Toner Cartridge: 9-10 Web site, Canon: 1-2 Weight, unit: A-8 White out: 7-14, 7-22 Windows 95: 2-4, 3-2, A-7 on-line help: 2-4 printer setup: 2-4–7 I-10 MP-L6000—USERS MANUAL/V000/12-97 Windows application scanning: 6-9 sending faxes: 4-16–19 Windows Printing System users: 10-26 Windows tabs, using: 2-5–7 Work area: 3-4 Z Zip drives: 10-26 Index
L6000 MultiPASS L6000 LCD Menu System Normal Functions Press Function and use arrows to scroll.
