MG3500 series Online-Handbuch Fehlersuche Deutsch (German)
Inhalt Fehlersuche. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Probleme mit der Netzwerkverbindung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Probleme mit dem Gerät bei Verwendung im Netzwerk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Das Gerät funktioniert plötzlich nicht mehr. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bild wird nicht oder nur teilweise gedruckt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Gedrucktes Papier wellt sich, oder Tinte ist verschmiert. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Papier ist verschmutzt/Bedruckte Oberfläche ist verkratzt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Rückseite des Papiers ist verschmutzt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aktualisieren der MP Drivers in einer Netzwerkumgebung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Deinstallieren des IJ Network Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info zu angezeigten Fehlern/Meldungen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 97 Wenn ein Fehler auftritt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1714. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 1715. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 1890. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 2100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
931. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 6932. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 6933. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 6936. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fehlersuche Das Gerät lässt sich nicht einschalten Druckvorgang lässt sich nicht starten Papier wird nicht richtig zugeführt/Fehler "Kein Papier" wird angezeigt Druckergebnisse sind nicht zufrieden stellend Es wird keine Tinte ausgegeben Papierstaus Wenn ein Fehler auftritt Einzelsuchfunktion Probleme mit der Netzwerkverbindung Probleme beim Drucken Probleme mit der Druckqualität Probleme beim Scannen Probleme mit dem Gerät Probleme beim Installieren/Herunterladen Info zu angezeigten Fehlern/Meldungen Wenn
Probleme mit der Netzwerkverbindung Probleme mit dem Gerät bei Verwendung im Netzwerk Es kann kein Gerät im Netzwerk erkannt werden Andere Probleme mit dem Netzwerk 8
Probleme mit dem Gerät bei Verwendung im Netzwerk Das Gerät funktioniert plötzlich nicht mehr Auf dem Druckerstatusmonitor des Geräts wird der Tintenstand nicht angezeigt Geringe Druckgeschwindigkeit Nach dem Austauschen eines Zugriffspunkts bzw.
Das Gerät funktioniert plötzlich nicht mehr Keine Kommunikation mit dem Gerät nach Ändern der Netzwerkeinstellungen möglich Keine Kommunikation mit Gerät über das Wireless LAN möglich Drucken oder Scannen über einen Computer im Netzwerk nicht möglich Keine Kommunikation mit dem Gerät nach Ändern der Netzwerkeinstellungen möglich Warten Sie, bis die IP-Adresse dem Computer zugewiesen wurde. Der Computer muss unter Umständen neu gestartet werden.
Überwachen des Status des drahtlosen Netzwerks Test 8 : Vergewissern Sie sich, dass der gültige drahtlose Kanal verwendet wird. Möglicherweise unterliegt der zu verwendende drahtlose Kanal abhängig von den im Computer installierten drahtlosen Netzwerkgeräten Einschränkungen. In der Bedienungsanleitung des Computers oder des drahtlosen Netzwerkgeräts finden Sie Informationen zum Angeben des gültigen drahtlosen Kanals.
Auf dem Druckerstatusmonitor des Geräts wird der Tintenstand nicht angezeigt Verwenden Sie den Druckertreiber mit bidirektionaler Kommunikation. Wählen Sie auf der Registerkarte Anschlüsse (Ports) im Eigenschaftendialogfeld des Druckertreibers die Option Bidirektionale Unterstützung aktivieren (Enable bidirectional support) aus.
Geringe Druckgeschwindigkeit : Das Gerät druckt oder scannt möglicherweise gerade einen umfangreichen, von einem anderen Computer gestarteten Auftrag. Test 1 : Vergewissern Sie sich, dass die Funkwellenübertragung einwandfrei funktioniert, und passen Sie die Installationspositionen an. Überwachen Sie dabei die Funkwellenübertragung mit dem IJ Network Tool. Test 2 Überwachen des Status des drahtlosen Netzwerks Stellen Sie sicher, dass sich zwischen Zugriffspunkt und Gerät keine Hindernisse befinden.
Nach dem Austauschen eines Zugriffspunkts bzw. dem Ändern der Einstellungen kann das Gerät nicht mehr verwendet werden Wenn Sie einen Zugriffspunkt autauschen, müssen Sie die Netzwerkeinrichtung des Geräts erneut durchführen. Nehmen Sie die Netzwerkeinstellungen erneut über die Installations-CD-ROM oder entsprechend den Anweisungen auf unserer Website vor. Wenn das Problem weiterhin besteht, finden Sie unten weitere Informationen.
Keine Möglichkeit zur Kommunikation mit Gerät nach Übernehmen der MAC-/IP-Adressenfilterung oder Eingeben eines WEP-/WPA-/WPA2-Schlüssels für den Zugriffspunkt 15
Es kann kein Gerät im Netzwerk erkannt werden Beim Einrichten der Netzwerkkommunikation wird das Gerät nicht erkannt Das Gerät wurde im Wireless LAN nicht gefunden 16
Beim Einrichten der Netzwerkkommunikation wird das Gerät nicht erkannt Wenn das Gerät beim Einrichten der Netzwerkkommunikation im Netzwerk nicht erkannt wird, überprüfen Sie die Netzwerkeinstellungen, bevor Sie eine erneute Geräteerkennung starten.
Bei „Einrichtung von drahtlosem LAN: Test 1“ wird das Gerät nicht erkannt Sind der Computer und das Netzwerkgerät (Router, Zugriffspunkt usw.) konfiguriert, und kann der Computer eine Verbindung mit dem Netzwerk herstellen? Vergewissern Sie sich, dass Sie Webseiten auf dem Computer anzeigen können. Falls keine Webseiten angezeigt werden: Konfigurieren Sie den Computer und das Netzwerkgerät.
Bei „Einrichtung von drahtlosem LAN: Test 2“ wird das Gerät nicht erkannt Wird die Einrichtung der Netzwerkkommunikation durch die Firewallfunktion Ihrer Sicherheitssoftware oder Ihres Computerbetriebssystems behindert? Die Kommunikation zwischen dem Gerät und dem Computer kann durch die Firewallfunktion Ihrer Sicherheitssoftware oder Ihres Computerbetriebssystems eingeschränkt werden. Überprüfen Sie die Firewalleinstellung Ihrer Sicherheitssoftware oder Ihres Betriebssystems bzw.
Bei „Einrichtung von drahtlosem LAN: Test 3“ wird das Gerät nicht erkannt Überprüfen Sie die Einstellungen des Zugriffspunkts. Überprüfen Sie die Netzwerkverbindungseinstellungen des Zugriffspunkts, wie IP-Adressenfilterung, MAC-Adressenfilterung oder DHCP-Funktion. Informationen zum Überprüfen der Einstellungen des Zugriffspunkts erhalten Sie in der mit dem Zugriffspunkt gelieferten Bedienungsanleitung oder beim Hersteller des Geräts.
Das Gerät wurde im Wireless LAN nicht gefunden Test 1 : Schalten Sie das Gerät erforderlichenfalls ein. Test 2 : Stellen Sie sicher, dass die Wi-Fi-Anzeige an der Vorderseite des Geräts leuchtet. Wenn die Wi-Fi-Anzeige nicht leuchtet, ist das drahtlose LAN inaktiv. Gehen Sie wie nachstehend beschrieben vor, um das drahtlose LAN zu aktivieren. 1. Drücken und halten Sie die Taste Stopp (Stop), bis die Alarm-Anzeige 18 mal blinkt. 2. Drücken Sie die Taste Farbe (Color). Falls die Wi-Fi-Anzeige leuchtet.
Der Zugriffspunkt befindet sich im Gebäude innerhalb des effektiven Bereichs für drahtlose Kommunikation. Stellen Sie das Gerät im Umkreis von 50 m/164 Fuß vom Zugriffspunkt auf. : Stellen Sie sicher, dass sich keine Störquellen für die Funkwellen in der Umgebung befinden. Test 10 Möglicherweise wird für Geräte wie Mikrowellen dieselbe Frequenzbandbreite wie für die Drahtlosstation verwendet. Stellen Sie die drahtlosen Geräte möglichst weit von potenziellen Störquellen auf.
Andere Probleme mit dem Netzwerk Name des Zugriffspunkts, SSID oder Netzwerkschlüssel ist nicht mehr bekannt Während der Einrichtung wird auf dem Bildschirm eine Meldung angezeigt Das Admin-Kennwort für das Gerät wurde vergessen Überprüfen von Netzwerkinformationen Es werden ständig Pakete gesendet Wiederherstellen der Netzwerkeinstellungen des Geräts auf die Herstellerstandards 23
Name des Zugriffspunkts, SSID oder Netzwerkschlüssel ist nicht mehr bekannt Keine Verbindung mit einem Zugriffspunkt möglich, für den ein WEP-/WPA-/WPA2-Schlüssel eingestellt ist (der WEP-/WPA-/WPA2-Schlüssel wurde vergessen) Einstellen eines WEP-/WPA-/WPA2-Schlüssels Keine Verbindung mit einem Zugriffspunkt möglich, für den ein WEP-/WPA-/ WPA2-Schlüssel eingestellt ist (der WEP-/WPA-/WPA2-Schlüssel wurde vergessen) Informationen zum Einrichten des Zugriffspunkts erhalten Sie in der Bedienungsanleitung für
Hinweis • Dieses Gerät unterstützt WPA-PSK (Persönlicher WPA) und WPA2-PSK (Persönlicher WPA2).
Während der Einrichtung wird auf dem Bildschirm eine Meldung angezeigt Bei der Einrichtung wird der Bildschirm Kennwort eingeben (Enter Password) angezeigt Der Bildschirm für die Einrichtung der Verschlüsselung wird nach Auswahl des Zugriffspunkts im Bildschirm Suchen (Search) angezeigt Die Meldung "Das Gerät wird mit dem unverschlüsselten drahtlosen Netzwerk verbunden" wird angezeigt Bei der Einrichtung wird der Bildschirm Kennwort eingeben (Enter Password) angezeigt Der folgende Bildschirm wird angezeigt
Das Admin-Kennwort für das Gerät wurde vergessen Initialisieren Sie die LAN-Einstellungen. Wiederherstellen der Netzwerkeinstellungen des Geräts auf die Herstellerstandards Führen Sie nach Initialisierung der LAN-Einstellungen die Einrichtung über die Installations-CD-ROM oder entsprechend den Anweisungen auf unserer Website durch.
Überprüfen von Netzwerkinformationen Überprüfen der IP-Adresse oder der MAC-Adresse des Geräts Überprüfen der IP-Adresse oder der MAC-Adresse des Computers Überprüfen der Kommunikationsfähigkeit zwischen Computer und Gerät bzw. Computer und Zugriffspunkt Überprüfen der Netzwerkeinstellungsinformationen Überprüfen der IP-Adresse oder der MAC-Adresse des Geräts Zur Überprüfung der IP-Adresse oder der MAC-Adresse des Geräts können Sie die Netzwerkinformationen über das Bedienfeld des Geräts drucken.
2. Geben Sie den Pingbefehl und die IP-Adresse des Zieldruckers oder des Zielzugriffspunkts ein, und drücken Sie anschließend die EINGABETASTE (Enter). XXX.XXX.XXX.XXX anpingen "XXX.XXX.XXX.XXX" ist die IP-Adresse des Zielgeräts. Falls die Kommunikation verfügbar ist, wird beispielsweise folgende Meldung angezeigt. Antwort von XXX.XXX.XXX.XXX: Bytes=32 Zeit=10ms TTL=255 Wird Anforderungszeitüberschreitung (Request timed out) angezeigt, ist keine Kommunikation möglich.
Es werden ständig Pakete gesendet Wenn IJ Network Scanner Selector EX aktiviert ist, werden in regelmäßigen Abständen Pakete gesendet, um zu überprüfen, ob über das Netzwerk mit dem Gerät kommuniziert werden kann. Bei Verwendung des Computers in einer Netzwerkumgebung, die sich von der für das Gerät eingerichteten Umgebung unterscheidet, deaktivieren Sie IJ Network Scanner Selector EX.
Wiederherstellen der Netzwerkeinstellungen des Geräts auf die Herstellerstandards Wichtig • Beachten Sie, dass durch die Initialisierung alle Netzwerkeinstellungen am Gerät gelöscht werden und Druck- bzw. Scanvorgänge von einem Computer über das Netzwerk u. U. nicht mehr möglich sind. Richten Sie das Gerät über die Installations-CD-ROM oder entsprechend den Anweisungen auf unserer Website ein, um es über das Netzwerk zu verwenden.
Probleme beim Drucken Druckvorgang lässt sich nicht starten Papierstaus Papier wird nicht richtig zugeführt/Fehler "Kein Papier" wird angezeigt Automatischer Duplexdruck wird nicht ordnungsgemäß ausgeführt Kopier-/Druckvorgang wird vorzeitig angehalten 32
Druckvorgang lässt sich nicht starten : Vergewissern Sie sich, dass der Netzstecker richtig angeschlossen ist, und schalten Sie das Gerät dann wieder ein, indem Sie die Taste EIN (ON) drücken. Test 1 Wenn die Anzeige EIN (ON) blinkt, wird das Gerät initialisiert. Warten Sie, bis die EIN (ON)-Anzeige nicht mehr blinkt, sondern leuchtet. Hinweis • Wenn Sie große Datenmengen wie z. B. Fotos oder Grafiken drucken, wird der Druckauftrag möglicherweise erst mit einiger Verzögerung gestartet.
• Klicken Sie unter Windows 7 im Menü Start auf Geräte und Drucker (Devices and Printers). • Klicken Sie unter Windows Vista auf das Menü Start > Systemsteuerung (Control Panel) > Hardware und Sound (Hardware and Sound) > Drucker (Printers). • Klicken Sie unter Windows XP auf das Menü Start > Systemsteuerung (Control Panel) > Drucker und andere Hardware (Printers and Other Hardware) > Drucker und Faxgeräte (Printers and Faxes). 3. Öffnen Sie die Eigenschaften des Druckertreibers für das Gerät.
Falls sich das Problem nicht beheben lässt, installlieren Sie die MP Drivers neu von der InstallationsCD-ROM oder unserer Website. Test 7 : Ist die Menge der Druckdaten äußerst groß? Klicken Sie auf der Registerkarte Seite einrichten (Page Setup) des Druckertreibers auf Druckoptionen (Print Options). Setzen Sie anschließend im angezeigten Dialogfeld die Option Vermeiden von Druckdatenverlust (Prevention of Print Data Loss) auf Ein (On).
Papierstaus Bei einem Papierstau blinkt die Alarm-Anzeige orange und es wird automatisch eine Meldung zur Fehlersuche auf dem Computerbildschirm ausgegeben. Führen Sie die in der Meldung beschriebenen Schritte aus. Informationen zum Entfernen von gestautem Papier finden Sie unter Supportcodeliste (Bei Papierstau). Hinweis • Sie können Maßnahmen zur Behebung von Fehlern mit Supportcodes auf Ihrem Computer finden, indem Sie nach einem Supportcode suchen.
Papier wird nicht richtig zugeführt/Fehler "Kein Papier" wird angezeigt Test 1 : Stellen Sie sicher, dass Papier eingelegt ist. Einlegen von Papier Test 2 : Achten Sie beim Einlegen von Papier auf die folgenden Punkte. • Wenn Sie zwei oder mehrere Blätter Papier einlegen, achten Sie darauf, den Papierstapel vor dem Einlegen zu lockern. • Wenn Sie zwei oder mehrere Blätter Papier einlegen, achten Sie darauf, dass die Kanten bündig ausgerichtet sind.
: Stellen Sie sicher, dass die Einstellungen für den Medientyp und das Papierformat mit dem eingelegten Papier übereinstimmen. Test 5 : Falls vom Gerät mehrere Blätter Normalpapier eingezogen werden, wählen Sie die Einstellung zum Verhindern des Doppeleinzugs von Normalpapier aus. Test 6 Falls vom Gerät mehrere Blätter Normalpapier eingezogen werden, wählen Sie die Einstellung zum Verhindern des Doppeleinzugs von Normalpapier über das Bedienfeld oder den Computer aus.
Automatischer Duplexdruck wird nicht ordnungsgemäß ausgeführt Test 1 : Ist die Einstellung für den automatischen Duplexdruck ausgewählt? Stellen Sie sicher, dass die Kontrollkästchen Duplexdruck (Duplex Printing) und Automatisch (Automatic) auf der Registerkarte Seite einrichten (Page Setup) im Druckertreiber-Setup-Fenster aktiviert sind. Duplexdruck : Stellen Sie sicher, dass sich das Format des eingelegten Papiers für den automatischen Duplexdruck eignet.
Kopier-/Druckvorgang wird vorzeitig angehalten Test 1 : Ist Papier eingelegt? Stellen Sie sicher, dass Papier eingelegt ist. Legen Sie Papier ein, falls im Gerät keines mehr vorhanden ist. : Sind in den zu druckenden Dokumenten viele Fotos oder Abbildungen enthalten? Test 2 Beim Drucken großer Datenmengen, wie Fotos oder Grafiken, benötigen das Gerät und der Computer unter Umständen mehr Zeit für die Verarbeitung der Daten.
Probleme mit der Druckqualität Druckergebnisse sind nicht zufrieden stellend Es wird keine Tinte ausgegeben 41
Druckergebnisse sind nicht zufrieden stellend Wenn das Druckergebnis aufgrund von weißen Streifen, versetzten Linien oder ungleichmäßiger Farbgebung nicht zufrieden stellend ist, überprüfen Sie zuerst die Einstellungen für Papier und Druckqualität. : Stimmen die Einstellungen für das Seitenformat und den Medientyp mit der Größe und dem Typ des eingelegten Papiers überein? Test 1 Wenn diese Einstellungen nicht richtig sind, kann kein zufrieden stellendes Druckergebnis erzielt werden.
Druckauftrag kann nicht abgeschlossen werden Test 1 : Wählen Sie die Einstellung aus, die das Komprimieren der Druckdaten nicht zulässt. Wenn Sie die Einstellung zum Verhindern der Komprimierung von Druckdaten mit der verwendeten Anwendungssoftware aktivieren, wird das Druckergebnis möglicherweise verbessert. Klicken Sie auf der Registerkarte Seite einrichten (Page Setup) des Druckertreibers auf Druckoptionen (Print Options).
Teil der Seite wird nicht gedruckt : Bei Verwendung des automatischen Duplexdrucks kann die im Folgenden beschriebene Situation auftreten. Test Bei Verwendung des automatischen Duplexdrucks ist der bedruckbare Bereich oben auf der Seite 2 mm / 0,08 Zoll schmaler als gewöhnlich. Aus diesem Grund kann es vorkommen, dass Inhalte am Ende einer Seite nicht gedruckt werden. Wählen Sie die Einstellung zur Verwendung der verringerten Druckgröße im Druckertreiber, um dies zu verhindern.
Keine Druckergebnisse/Unscharfer Druck/Farben sind falsch/ Weiße Streifen Keine Druckergebnisse Unscharfer Druck Farben sind falsch Weiße Streifen 45
Test 1 : Haben Sie die Einstellungen für Papier und Druckqualität überprüft? Druckergebnisse sind nicht zufrieden stellend : Drucken Sie das Düsentestmuster und führen Sie sämtliche erforderlichen Wartungsmaßnahmen wie die Druckkopfreinigung durch. Test 2 Drucken Sie das Düsentestmuster, um zu überprüfen, ob die Tinte von den Druckkopfdüsen ordnungsgemäß ausgegeben wird.
Weitere Informationen zum Kopieren finden Sie in den Abschnitten unten: Test 6 : Ist die Auflagefläche verschmutzt? Reinigen Sie die Auflagefläche. Reinigen der Auflagefläche und des Vorlagendeckels Test 7 : Stellen Sie sicher, dass das Dokument korrekt auf der Auflagefläche liegt.
Farben sind unscharf Test 1 : Wird das Düsentestmuster ordnungsgemäß gedruckt? Drucken Sie das Düsentestmuster, um zu überprüfen, ob die Tinte von den Druckkopfdüsen ordnungsgemäß ausgegeben wird. Informationen zum Drucken eines Düsentestmusters, zur Druckkopfreinigung und zur Intensivreinigung des Druckkopfs finden Sie unter Druck wird blasser oder Farben sind falsch.
Linien sind schief Test 1 : Haben Sie die Einstellungen für Papier und Druckqualität überprüft? Druckergebnisse sind nicht zufrieden stellend Test 2 : Führen Sie die Druckkopfausrichtung durch. Wenn Linien versetzt gedruckt werden oder der Ausdruck aus anderen Gründen nicht zufrieden stellend ist, muss der Druckkopf ausgerichtet werden. Ausrichten des Druckkopfs Hinweis • Wenn das Problem nach der Druckkopfausrichtung nicht behoben ist, sollten Sie eine manuelle Druckkopfausrichtung durchführen.
Linie wird nicht oder nur teilweise gedruckt : Wird die Funktion zum Drucken des Seitenlayouts oder die Heftrandfunktion verwendet? Test 1 Wird die Funktion "Seitenlayoutdruck" oder die Heftrandfunktion verwendet, werden dünne Linien möglicherweise nicht gedruckt. Versuchen Sie, die Linien im Dokument dicker zu machen. Test 2 : Ist die Menge der Druckdaten äußerst groß? Klicken Sie auf der Registerkarte Seite einrichten (Page Setup) des Druckertreibers auf Druckoptionen (Print Options).
Bild wird nicht oder nur teilweise gedruckt Test 1 : Wählen Sie die Einstellung aus, die das Komprimieren der Druckdaten nicht zulässt. Wenn Sie die Einstellung zum Verhindern der Komprimierung von Druckdaten mit der verwendeten Anwendungssoftware aktivieren, wird das Druckergebnis möglicherweise verbessert. Klicken Sie auf der Registerkarte Seite einrichten (Page Setup) des Druckertreibers auf Druckoptionen (Print Options).
Gedrucktes Papier wellt sich, oder Tinte ist verschmiert Auf dem bedruckten Papier ist Tinte verschmiert Das bedruckte Papier wellt sich Test 1 : Haben Sie die Einstellungen für Papier und Druckqualität überprüft? Druckergebnisse sind nicht zufrieden stellend : Falls die Intensität hoch eingestellt ist, verringern Sie die Einstellung für Intensität, und starten Sie einen neuen Druckvorgang.
Papier ist verschmutzt/Bedruckte Oberfläche ist verkratzt Papier ist verschmutzt Die Kanten des Papiers sind verschmutzt Bedruckte Oberfläche ist verschmutzt Bedruckte Oberfläche ist verkratzt Test 1 : Haben Sie die Einstellungen für Papier und Druckqualität überprüft? Druckergebnisse sind nicht zufrieden stellend Test 2 : Wird ein geeigneter Papiertyp verwendet? Prüfen Sie Folgendes: • Überprüfen Sie, ob das verwendete Papier für den Zweck geeignet ist.
1. Rollen Sie das Papier wie unten dargestellt in die der Wellung entgegengesetzte Richtung. 2. Prüfen Sie, ob das Papier nun eben ist. Wir empfehlen, das auf diese Weise geglättete Papier blattweise zu bedrucken. Hinweis • Je nach verwendetem Medientyp wird das Papier möglicherweise verschmutzt, oder es wird möglicherweise nicht richtig eingezogen, auch wenn es nicht nach innen abgeknickt ist.
• So legen Sie Einstellungen über den Computer fest Öffnen Sie das Druckertreiber-Setup-Fenster und aktivieren Sie unter Benutzerdefinierte Einstellungen (Custom Settings) auf der Registerkarte Wartung (Maintenance) das Kontrollkästchen Papierabrieb verhindern (Prevent paper abrasion). Klicken Sie dann auf OK. Weitere Informationen zum Öffnen des Druckertreiber-Setup-Fensters finden Sie unter Öffnen des Druckertreiber-Setup-Fensters.
Test 10 : Stellen Sie eine längere Dauer für das Trocknen der Druckoberfläche ein. Somit wird ausreichend Zeit für das Trocknen der Druckoberfläche eingeräumt, wodurch ein Verschmieren und Verkratzen des Papiers verhindert wird. 1. Stellen Sie sicher, dass das Gerät eingeschaltet ist. 2. Öffnen Sie das Druckertreiber-Setup-Fenster. Öffnen des Druckertreiber-Setup-Fensters 3. Klicken Sie auf die Registerkarte Wartung (Maintenance) und dann auf Benutzerdefinierte Einstellungen (Custom Settings). 4.
Rückseite des Papiers ist verschmutzt Test 1 : Haben Sie die Einstellungen für Papier und Druckqualität überprüft? Druckergebnisse sind nicht zufrieden stellend Test 2 : Führen Sie eine Bodenplattenreinigung durch, um das Innere des Geräts zu reinigen. Reinigen des Geräteinneren (Bodenplattenreinigung Hinweis • Bei randlosem Druck, Duplexdruck oder übermäßigem Drucken kann der Innenraum des Druckers mit Tinte verschmutzt werden.
Im Ausdruck erscheinen vertikale Linien Test : Haben Sie Papier des richtigen Formats eingelegt? Wenn das Format des eingelegten Papiers größer ist als das festgelegte Format, werden die Ränder möglicherweise mit vertikalen Linien bedruckt. Stellen Sie das richtige Format entsprechend dem Format des eingelegten Papiers ein. Druckergebnisse sind nicht zufrieden stellend Hinweis • Der Verlauf des vertikalen Linienmusters kann je nach Bilddaten oder Druckeinstellung variieren.
Farben sind ungleichmäßig oder weisen Streifen auf Farben sind ungleichmäßig Farben sind streifig Test 1 : Haben Sie die Einstellungen für Papier und Druckqualität überprüft? Druckergebnisse sind nicht zufrieden stellend Test 2 : Drucken Sie das Düsentestmuster und führen Sie sämtliche erforderlichen Wartungsmaßnahmen wie die Druckkopfreinigung durch. Drucken Sie das Düsentestmuster, um zu überprüfen, ob die Tinte von den Druckkopfdüsen ordnungsgemäß ausgegeben wird.
Test 3 : Führen Sie die Druckkopfausrichtung durch. Ausrichten des Druckkopfs Hinweis • Wenn das Problem nach der Druckkopfausrichtung nicht behoben ist, sollten Sie eine manuelle Druckkopfausrichtung durchführen. Weitere Informationen finden Sie unter Ausrichten des Druckkopfs über den Computer.
Es wird keine Tinte ausgegeben Test 1 : Wenn eine FINE-Patrone leer ist, tauschen Sie sie gegen eine neue aus. Test 2 : Ist die FINE-Patrone ordnungsgemäß eingesetzt? Wenn die FINE-Patrone nicht richtig eingesetzt ist, kann die Tinte möglicherweise nicht richtig ausgegeben werden. Öffnen Sie die Abdeckung der Papierausgabe. Dann wird die Abdeckung für Kopf geöffnet. Drücken Sie den Tintenpatronen-Sperrhebel nach oben, um sicherzustellen, dass die FINE-Patrone ordnungsgemäß eingesetzt ist.
Probleme beim Scannen Probleme beim Scannen Scan-Ergebnisse sind nicht zufrieden stellend Software-Probleme 62
Probleme beim Scannen Der Scanner funktioniert nicht ScanGear (Scanner-Treiber) startet nicht Eine Fehlermeldung wird angezeigt und der Bildschirm von ScanGear (Scanner-Treiber) wird nicht geöffnet Es können nicht mehrere Objekte gleichzeitig gescannt werden Im automatischen Scanmodus kann nicht ordnungsgemäß gescannt werden Niedrige Scan-Geschwindigkeit Die Meldung "Nicht genügend Arbeitsspeicher.
Der Scanner funktioniert nicht Test 1: Stellen Sie sicher, dass der Scanner oder Drucker eingeschaltet ist. Test 2: Schließen Sie das USB-Kabel an einen anderen USBAnschluss am Computer an. Test 3: Wenn das USB-Kabel an einen USB-Hub angeschlossen ist, ziehen Sie es vom USB-Hub ab und verbinden es mit einem USB-Anschluss am Computer. Test 4: Starten Sie den Computer neu.
ScanGear (Scanner-Treiber) startet nicht Test 1: Stellen Sie sicher, dass die MP Drivers installiert sind. Falls MP Drivers noch nicht installiert ist, installieren Sie die Treiber von der InstallationsCD-ROM oder unserer Webseite. Test 2: Wählen Sie Ihren Scanner oder Drucker im Menü der Anwendung aus. Wichtig Falls der Name Ihres Scanners oder Druckers mehrmals angezeigt wird, wählen Sie den Namen aus, in dem WIA nicht vorkommt. Hinweis Je nach Anwendung müssen Sie dazu ggf. andere Schritte ausführen.
Eine Fehlermeldung wird angezeigt und der Bildschirm von ScanGear (Scanner-Treiber) wird nicht geöffnet Test 1: Stellen Sie sicher, dass der Scanner oder Drucker eingeschaltet ist. Test 2: Schalten Sie den Scanner oder Drucker aus, und schließen Sie dann das USB-Kabel und das Netzkabel erneut an. Test 3: Schließen Sie das USB-Kabel an einen anderen USBAnschluss am Computer an.
Es können nicht mehrere Objekte gleichzeitig gescannt werden Test 1: Stellen Sie sicher, dass die Objekte ordnungsgemäß positioniert wurden. Objekte platzieren (beim Scannen über den Computer) Test 2: Überprüfen Sie, ob ein Objekt ordnungsgemäß gescannt wird. Einige Programme bieten keine Unterstützung für das Scannen mehrerer Bilder. Scannen Sie in diesem Fall jedes Dokument einzeln.
Im automatischen Scanmodus kann nicht ordnungsgemäß gescannt werden Test 1: Stellen Sie sicher, dass die Objekte ordnungsgemäß positioniert wurden. Objekte platzieren (beim Scannen über den Computer) Test 2: Möglicherweise wird das Scannen mehrerer Objekte nicht unterstützt. Einige Programme bieten keine Unterstützung für das Scannen mehrerer Bilder. Scannen Sie in diesem Fall jedes Dokument einzeln.
Niedrige Scan-Geschwindigkeit Test 1: Scannen Sie mit einer Ausgabeauflösung von etwa 150 dpi, wenn Sie das Bild auf einem Bildschirm anzeigen möchten. Scannen Sie mit etwa 300 dpi, wenn Sie das Dokument drucken möchten. Auflösung Test 2: Setzen Sie Farbkorrektur (Fading Correction), Bildglättung (Grain Correction) usw. auf Ohne (None). Weitere Informationen finden Sie im Abschnitt "Bildeinstellungen" des entsprechenden Modells auf der Startseite des Online-Handbuchs.
Die Meldung "Nicht genügend Arbeitsspeicher." wird angezeigt Test 1: Beenden Sie laufende Anwendungen und versuchen Sie es erneut. Test 2: Reduzieren Sie die Auflösung oder das Ausgabeformat und scannen Sie erneut.
Der Computer hört während des Scannens auf zu arbeiten Test 1: Starten Sie den Computer neu, verringern Sie die Ausgabeauflösung in ScanGear (Scanner-Treiber) und scannen Sie erneut. Weitere Informationen finden Sie im Abschnitt "Ausgabe-Einstellungen" des entsprechenden Modells auf der Startseite des Online-Handbuchs. Test 2: Löschen Sie nicht benötigte Dateien, um auf Ihrer Festplatte freien Platz zu schaffen, und scannen Sie dann erneut.
Der Scanner funktioniert nach der Aktualisierung von Windows nicht mehr Test: Ziehen Sie das USB-Kabel ab. Deinstallieren (löschen) Sie die MP Drivers und IJ Scan Utility und installieren Sie sie neu. • Schritt 1: Deinstallieren Sie die MP Drivers. Informationen zum Löschen der MP Drivers finden Sie im Abschnitt "Löschen der nicht benötigten MP Drivers" des entsprechenden Modells auf der Startseite des OnlineHandbuchs. • Schritt 2: Deinstallieren Sie IJ Scan Utility. • Windows 8: 1.
3. Wenn eine Bestätigungsmeldung angezeigt wird, klicken Sie auf Ja (Yes). 4. Wenn die Deinstallation abgeschlossen ist, klicken Sie auf OK. IJ Scan Utility wird gelöscht. Hinweis Unter Windows 7 und Windows Vista wird beim Installieren, Deinstallieren oder Starten von Software möglicherweise ein Dialogfeld zur Bestätigung oder Warnung angezeigt. Dieses Dialogfeld wird angezeigt, wenn Administratorrechte zum Ausführen einer Aufgabe erforderlich sind.
Das gescannte Bild lässt sich nicht öffnen Test: Wenn das Datenformat von der Anwendung nicht unterstützt wird, scannen Sie das Bild erneut, und wählen Sie ein gängiges Datenformat wie z. B. JPEG beim Speichern aus. Weitere Informationen hierzu finden Sie im Handbuch der Anwendung. Wenden Sie sich bei Fragen an den Hersteller der Anwendung.
Scan-Ergebnisse sind nicht zufrieden stellend Die Scan-Qualität (auf dem Bildschirm angezeigtes Bild) ist schlecht Um das gescannte Bild herum treten unerwünschte weiße Bereiche auf Das Scannen mit der richtigen Größe ist nicht möglich Das Objekt wurde richtig platziert, das Bild jedoch schräg gescannt Gescannte Bilder werden auf dem Bildschirm vergrößert (verkleinert) angezeigt 75
Die Scan-Qualität (auf dem Bildschirm angezeigtes Bild) ist schlecht Test 1: Erhöhen Sie die Scanauflösung, wenn das Bild unscharf angezeigt wird. Auflösung Test 2: Stellen Sie die Anzeigegröße auf 100 % ein. Einige Anwendungen zeigen Bilder nicht deutlich an, wenn die Anzeigegröße zu klein sind. Test 3: Wenn ein Moiré-Effekt (Streifenmuster) auftritt, führen Sie folgende Aktionen durch und scannen Sie erneut.
Test 4: Prüfen Sie die Farbtiefe des Bildschirms. Weitere Informationen zum Prüfen der Farbtiefe des Monitors finden Sie in der Hilfe zu Windows oder im Handbuch des Monitors. Test 5: Reinigen Sie die Auflagefläche und den Vorlagendeckel. Test 6: Wenn das Dokument von schlechter Qualität ist (verschmutzt, verblasst usw.), wenden Sie die Optionen Staub und Kratzer reduzieren (Reduce Dust and Scratches), Farbkorrektur (Fading Correction), Bildglättung (Grain Correction) usw.
Um das gescannte Bild herum treten unerwünschte weiße Bereiche auf Test: Legen Sie den Scan-Bereich fest. (Automatisch beschneiden) in der Gesamtbildansicht von ScanGear Klicken Sie auf (Scanner-Treiber), um den Schnittrahmen (Scan-Bereich) entsprechend der Objektgröße automatisch festzulegen. Sie können den Scan-Bereich auch manuell in der Miniaturansicht festlegen, z. B. wenn das Objekt weiße Ränder aufweist (z. B. in Fotos) oder wenn Sie benutzerdefinierte Schnittrahmen erstellen möchten.
Das Scannen mit der richtigen Größe ist nicht möglich Test: Stellen Sie sicher, dass die Objekte ordnungsgemäß positioniert wurden.
Das Objekt wurde richtig platziert, das Bild jedoch schräg gescannt Test: Deaktivieren Sie das Kontrollkästchen Schräge Textdokumente korrigieren (Correct slanted text document), wenn Dokument (Document) oder Zeitschrift (Magazine) als Objekttyp ausgewählt ist, und scannen Sie das Objekt erneut.
Gescannte Bilder werden auf dem Bildschirm vergrößert (verkleinert) angezeigt Test 1: Ändern Sie die Anzeigeeinstellung in der Anwendung. Weitere Informationen hierzu finden Sie im Handbuch der Anwendung. Wenden Sie sich bei Fragen an den Hersteller der Anwendung. Hinweis Sie können die Bildgröße in Paint nicht verkleinern. Um die Anzeigegröße zu verringern, öffnen Sie die Bilder in einer Anwendung. Test 2: Ändern Sie die Auflösungseinstellung in ScanGear (Scanner-Treiber) und scannen Sie erneut.
Software-Probleme Das E-Mail-Programm, das Sie verwenden möchten, wird im Bildschirm zur Auswahl eines E-Mail-Programms nicht angezeigt 82
Das E-Mail-Programm, das Sie verwenden möchten, wird im Bildschirm zur Auswahl eines E-Mail-Programms nicht angezeigt Test: Stellen Sie sicher, dass die MAPI des E-Mail-Programms aktiviert ist. Weitere Informationen zur MAPI-Einstellung finden Sie im Handbuch zum E-MailProgramm.
Probleme mit dem Gerät Das Gerät lässt sich nicht einschalten Das Gerät wird unbeabsichtigt ausgeschaltet Verbindung zum Computer kann mit USB-Kabel nicht ordnungsgemäß hergestellt werden Keine Kommunikation mit Gerät über USB-Verbindung möglich Der Druckerstatusmonitor wird nicht angezeigt 84
Das Gerät lässt sich nicht einschalten Test 1 : Drücken Sie die Taste EIN (ON). : Vergewissern Sie sich, dass der Netzstecker richtig an den Netzkabelanschluss des Geräts angeschlossen ist, und schalten Sie den Drucker wieder ein. Test 2 : Trennen Sie das Gerät von der Stromversorgung, und schließen Sie das Gerät dann wieder an. Schalten Sie das Gerät erst nach mindestens 2 Minuten wieder ein. Test 3 Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
Das Gerät wird unbeabsichtigt ausgeschaltet Test : Deaktivieren Sie die Einstellung für das automatische Ausschalten des Geräts. Das Gerät wird nach Ablauf des von Ihnen eingegebenen Zeitraums automatisch ausgeschaltet, wenn Sie die Einstellung zum automatischen Ausschalten aktivieren. Wenn das Gerät nicht automatisch ausgeschaltet werden soll, öffnen Sie das Druckertreiber-Setup-Fenster, und wählen Sie in Autom.
Verbindung zum Computer kann mit USB-Kabel nicht ordnungsgemäß hergestellt werden Geringe Druck- oder Scangeschwindigkeit/Hi-Speed-USB-Verbindung funktioniert nicht/Die Meldung "Dieses Gerät kann eine höhere Leistung erbringen (This device can perform faster)" wird angezeigt Ist die Systemumgebung nicht vollständig mit Hi-Speed USB kompatibel, wird das Gerät mit einer niedrigeren Geschwindigkeit (entsprechend USB 1.1) betrieben.
Keine Kommunikation mit Gerät über USB-Verbindung möglich Test 1 : Schalten Sie das Gerät erforderlichenfalls ein. Test 2 : Stellen Sie sicher, dass das USB-Kabel ordnungsgemäß angeschlossen ist. Unter Anschließen des Geräts an den Computer mit einem USB-Kabel finden Sie Informationen zum ordnungsgemäßen Anschluss des USB-Kabels. Test 3 : Starten Sie das IJ Network Tool nicht während eines Druckvorgangs. Test 4 : Drucken Sie nicht, während das IJ Network Tool ausgeführt wird.
Der Druckerstatusmonitor wird nicht angezeigt Test : Ist der Druckerstatusmonitor aktiviert? Stellen Sie sicher, dass im Menü Optionen (Option) des Druckerstatusmonitors die Option Statusmonitor aktivieren (Enable Status Monitor) ausgewählt ist. 1. Öffnen Sie das Druckertreiber-Setup-Fenster. Öffnen des Druckertreiber-Setup-Fensters 2. Klicken Sie auf der Registerkarte Wartung (Maintenance) auf Druckerstatus anzeigen (View Printer Status). 3.
Probleme beim Installieren/Herunterladen Die MP Drivers können nicht installiert werden Easy-WebPrint EX wird nicht gestartet bzw.
Die MP Drivers können nicht installiert werden • Falls der Installationsvorgang nicht automatisch gestartet wird, wenn die Installations-CD-ROM in das Laufwerk des Computers eingelegt wird: Starten Sie die Installation entsprechend den nachstehenden Anweisungen. 1. Führen Sie die unten stehenden Schritte durch. ◦ Wählen Sie unter Windows 8 auf dem Desktop in der Taskleiste (Taskbar) das ExplorerSymbol aus, und wählen Sie dann aus der auf der linken Seite angezeigten Liste Computer aus.
• Falls Sie nach dem Bildschirm Druckeranschluss (Printer Connection) nicht fortfahren können: Hinweis • Abhängig vom verwendeten Computer wird möglicherweise Der Drucker wird nicht erkannt. Überprüfen Sie die Verbindung. (The printer is not detected. Check the connection.) angezeigt. : Vergewissern Sie sich, dass das USB-Kabel richtig an das Gerät und den Computer angeschlossen ist. Test 1 : Befolgen Sie die unten stehenden Schritte, um das Gerät und den Computer wieder anzuschließen. Test 2 1.
7. Legen Sie die CD-ROM erneut ein und installieren Sie die MP Drivers. • In anderen Fällen: Installieren Sie die MP Drivers neu. Wenn die MP Drivers nicht richtig installiert wurden, deinstallieren Sie die MP Drivers, starten Sie den Computer neu, und installieren Sie die MP Drivers erneut. Löschen der nicht benötigten MP Drivers Falls Sie die MP Drivers neu installieren, installieren Sie die MP Drivers von der Installations-CD-ROM oder unserer Website.
Easy-WebPrint EX wird nicht gestartet bzw. das Easy-WebPrint EXMenü nicht angezeigt Wenn Easy-WebPrint EX nicht gestartet oder das Menü nicht in Internet Explorer angezeigt wird, überprüfen Sie Folgendes. : Wird Canon Easy-WebPrint EX im Menü Symbolleisten (Toolbars) des Menüs Ansicht (View) des Internet Explorer angezeigt? Test 1 Wenn Canon Easy-WebPrint EX nicht angezeigt wird, ist Easy-WebPrint EX nicht auf Ihrem Computer installiert.
Aktualisieren der MP Drivers in einer Netzwerkumgebung Laden Sie die neuesten MP Drivers zuvor herunter. Sie können über das Internet auf unsere Website zugreifen und die neuesten MP Drivers herunterladen, um die neusten MP Drivers für Ihr Druckermodell zu erhalten. Führen Sie nach der Deinstallation der MP Drivers die Installation der neuesten MP Drivers entsprechend der üblichen Vorgehensweise aus.
Deinstallieren des IJ Network Tool Führen Sie die unten angegebenen Schritte aus, um das IJ Network Tool vom Computer zu deinstallieren. Wichtig • Selbst wenn das IJ Network Tool deinstalliert ist, können Sie immer noch mit dem Computer über das Netzwerk drucken und scannen. Sie können über das Netzwerk jedoch nicht die Netzwerkeinstellungen ändern. • Melden Sie sich mit Administratorrechten am Benutzerkonto an. 1. Folgen Sie der Verfahrensweise zum Deinstallieren des IJ Network Tool. • In Windows 8: 1.
Info zu angezeigten Fehlern/Meldungen Wenn ein Fehler auftritt Eine Meldung wird angezeigt 97
Wenn ein Fehler auftritt Wenn beim Drucken ein Fehler auf dem Gerät auftritt, beispielsweise bei fehlendem Papier oder Papierstaus, wird automatisch eine Meldung zur Fehlersuche ausgegeben. Führen Sie die in der Meldung beschriebenen Schritte aus. Beim Auftreten eines Fehlers wird ein Supportcode (Fehlernummer) auf dem Computerbildschirm oder auf der Alarm-Anzeige angezeigt. Bei einigen Fehlerarten blinken die EIN (ON)-Anzeige und die AlarmAnzeige abwechselnd.
9 Blinkzeichen Möglicherweise wurde das Schutzmaterial für die FINEPatronen-Halterung oder das Klebeband nicht von der Halterung entfernt. 1890 10 Blinkzeichen Das eingelegte Papier ist mit dem automatischen Duplexdruck nicht kompatibel. 1310 11 Blinkzeichen Der automatische Duplexdruck kann mit der aktuellen Papierformateinstellung nicht durchgeführt werden. 4103 12 Blinkzeichen Sie können den Inhalt von CREATIVE PARK PREMIUM nicht drucken.
Andere als die obigen Fälle Es ist ein Druckerfehler aufgetreten. 5011, 5012, 5200, 5400, 6000, 6500, 6800, 6801, 6900, 6901, 6902, 6910, 6911, 6930, 6931, 6932, 6933, 6936, 6937, 6938, 6940, 6941, 6942, 6943, 6944, 6945, 6946 • Wenn ein Supportcode und eine Meldung auf dem Computerbildschirm angezeigt werden: Hinweis • Sie können Maßnahmen zur Behebung von Fehlern mit Supportcodes auf Ihrem Computer finden, indem Sie nach einem Supportcode suchen.
Eine Meldung wird angezeigt In diesem Abschnitt werden einige Fehler oder Meldungen beschrieben. Hinweis • Bei einigen Fehlern oder Meldungen wird ein Supportcode (Fehlernummer) auf dem Computerbildschirm angezeigt. Weitere Informationen zu Fehlern mit Supportcodes finden Sie unter Supportcodeliste.
• Klicken Sie unter Windows Vista auf das Menü Start > Systemsteuerung (Control Panel) > Hardware und Sound (Hardware and Sound) > Drucker (Printers). • Klicken Sie unter Windows XP auf das Menü Start > Systemsteuerung (Control Panel) > Drucker und andere Hardware (Printers and Other Hardware) > Drucker und Faxgeräte (Printers and Faxes). 3. Öffnen Sie die Eigenschaften des Druckertreibers für das Gerät.
Falls sich das Problem nicht beheben lässt, installlieren Sie die MP Drivers neu von der InstallationsCD-ROM oder unserer Website. : Vergewissern Sie sich, dass das USB-Kabel richtig an das Gerät und den Computer angeschlossen ist. Test 3 Wenn das Gerät über ein USB-Kabel mit dem Computer verbunden ist, prüfen Sie die folgenden Punkte: • Wenn Sie ein Verteilergerät, wie z. B. einen USB-Hub, verwenden, entfernen Sie es, und schließen Sie das Gerät direkt an den Computer an.
• "Spool-Vorgang konnte aufgrund von unzureichendem Festplattenspeicher nicht ausgeführt werden (Could not spool successfully due to insufficient disk space)" Löschen Sie nicht benötigte Dateien, um mehr Festplattenspeicherplatz freizugeben. • "Spool-Vorgang konnte aufgrund von unzureichendem Arbeitsspeicher nicht ausgeführt werden (Could not spool successfully due to insufficient memory)" Beenden Sie andere ausgeführte Anwendungssoftware, um Arbeitsspeicher freizugeben.
Hinweis • Beim Übermitteln der Daten wird ein Warnhinweis wie z. B. Internetsicherheit angezeigt. Bestätigen Sie in diesem Fall, dass der Programmname "IJPLMUI.exe" ist und lassen Sie die Ausführung zu. • Wenn Sie das Kontrollkästchen Ab nächstem Mal automatisch senden (Send automatically from the next time) deaktivieren, werden die Informationen ab dem zweiten Mal nicht mehr automatisch übermittelt, und ein Bestätigungsbildschirm wird zum Zeitpunkt der nächsten Umfrage angezeigt.
Hinweis • Wenn Sie Deinstallieren (Uninstall) (oder Entfernen (Remove) unter Windows XP) auswählen, wird das Extended Survey Program für Inkjet-Drucker/Scanner/Faxgeräte (Inkjet Printer/Scanner/Fax Extended Survey Program) deinstalliert. Folgen Sie den Bildschirmanweisungen.
Wenn das Problem weiterhin besteht Wenn Sie das Problem mit den Hinweisen in diesem Kapitel nicht beheben können, wenden Sie sich an den Händler, bei dem Sie das Gerät gekauft haben, oder an das Service-Center. Die Mitarbeiter des Kundendiensts von Canon sind darin geschult, technischen Support zur Zufriedenheit der Kunden anzubieten. Vorsicht • Wenn das Gerät ungewöhnliche Geräusche oder Gerüche entwickelt oder Rauch entsteht, schalten Sie es sofort aus.
Supportcodeliste (MG3510, MG3520, MG3540, MG3550, MG3560, MG3570, MG3580) Der Supportcode wird auf dem Computerbildschirm angezeigt, wenn ein Fehler aufgetreten ist. Der "Supportcode" ist die Fehlernummer. Er wird zusammen mit einer Fehlermeldung angezeigt. Überprüfen Sie bei der Anzeige eines Fehlers den Supportcode, der auf dem Computerbildschirm angezeigt wird, und befolgen Sie die entsprechenden Schritte.
• A000 bis ZZZZ B200 Informationen zu Supportcodes bei Papierstau finden Sie auch in der Supportcodeliste (Bei Papierstau).
Supportcodeliste (Bei Papierstau) Falls ein Papierstau aufgetreten ist, entfernen Sie das gestaute Papier entsprechend den folgenden spezifischen Anleitungen.
1300 Ursache Im Papierausgabeschacht ist ein Papierstau aufgetreten. Maßnahme Wenn Sie das gestaute Papier am Papierausgabeschacht sehen können, entfernen Sie es gemäß folgender Anweisung. Hinweis • Falls Sie das Gerät ausschalten müssen, um gestautes Papier während des Druckvorgangs zu entfernen, drücken Sie zum Abbrechen von Druckaufträgen vor dem Ausschalten des Geräts die Taste Stopp (Stop). 1. Ziehen Sie das Papier langsam heraus.
Wenn Sie das Gerät in Schritt 1 ausgeschaltet haben, wurden alle Druckaufträge in der Warteschlange abgebrochen. Starten Sie die Druckaufträge ggf. neu. Hinweis • Prüfen Sie beim erneuten Einlegen von Papier, ob Sie zum Druck geeignetes Papier verwenden, und legen Sie es richtig ein. • Wir empfehlen Papier mit einem anderen Format als A5 zum Drucken von Dokumenten mit Fotos oder Grafiken, andernfalls kann sich das Papier bei der Ausgabe wellen und dadurch Papierstaus verursachen.
1303 Ursache Im Gerät ist an der Transporteinheit ein Papierstau aufgetreten. Maßnahme Wenn Sie das gestaute Papier am vorderen Fach sehen können oder Sie das Papier weder am Papierausgabeschacht noch am vorderen Fach sehen können, entfernen Sie das Papier über die Transporteinheit. Entfernen Sie das Papier entsprechend den nachstehenden Anweisungen.
5. Ziehen Sie das gestaute Papier langsam heraus. Stützen Sie das Gerät beim Entfernen des gestauten Papiers mit Ihrer Hand ab, damit es nicht umfällt. Hinweis • Wenn das Papier aufgerollt ist und sich nur schwer herausziehen lässt, fassen Sie das gestaute Papier an den Kanten an, und entfernen Sie es.
Hinweis • Stellen Sie das Gerät nach dem Schließen der Transporteinheit sofort wieder in die ursprüngliche Position. 7. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. 8. Legen Sie das Papier wieder ein. Alle Druckaufträge in der Warteschlange werden abgebrochen. Starten Sie die Druckaufträge ggf. neu. Wenn Sie das Papier nicht entfernen können, das Papier im Gerät reißt oder der Papierstau auch nach dem Entfernen des Papiers nicht behoben ist, wenden Sie sich an das Service-Center.
1304 Ursache Während des automatischen Duplexdrucks tritt ein Papierstau auf. Maßnahme Wenn der Papierstau während des automatischen Duplexdrucks auftritt, entfernen Sie das Papier entsprechend der folgenden Anleitung. Hinweis • Falls Sie das Gerät ausschalten müssen, um gestautes Papier während des Druckvorgangs zu entfernen, drücken Sie zum Abbrechen von Druckaufträgen vor dem Ausschalten des Geräts die Taste Stopp (Stop). 1. Ziehen Sie das Papier langsam aus dem Papierausgabeschacht heraus.
• Stellen Sie das Gerät auf einer breiten und flachen Oberfläche wie einem Schreibtisch auf die Seite. • Halten Sie das Gerät gut fest, wenn Sie es auf die Seite stellen, und achten Sie darauf, dass es nicht gegen harte Gegenstände stößt. 5. Entfernen Sie noch nicht entferntes Schutzmaterial von der Transporteinheit. 6. Drücken Sie den Hebel, um die Transporteinheit zu öffnen. Stützen Sie das Gerät beim Öffnen der Transporteinheit mit Ihrer Hand ab, damit es nicht umfällt. 7.
• Wenn Sie das gestaute Papier nicht über die Transporteinheit entfernen können, schließen Sie die Transporteinheit, bringen Sie das Gerät in die ursprüngliche Position, und öffnen Sie anschließend die Abdeckung der Papierausgabe, um das Papier zu entfernen. Im Gerät ist ein Papierstau aufgetreten 8. Schließen Sie die Transporteinheit. Hinweis • Stellen Sie das Gerät nach dem Schließen der Transporteinheit sofort wieder in die ursprüngliche Position. 9.
Im Gerät ist ein Papierstau aufgetreten Falls das gestaute Papier reißt und es sich weder aus dem Papierausgabeschacht noch aus der Transporteinheit entfernen lässt oder wenn das gestaute Papier im Gerät verbleibt, entfernen Sie es gemäß nachstehender Anleitung. Hinweis • Falls Sie das Gerät ausschalten müssen, um gestautes Papier während des Druckvorgangs zu entfernen, drücken Sie zum Abbrechen von Druckaufträgen vor dem Ausschalten des Geräts die Taste Stopp (Stop). 1.
4. Halten Sie das gestaute Papier mit Ihren Händen fest. Wenn das Papier aufgerollt ist, ziehen Sie es heraus. 5. Ziehen Sie das gestaute Papier langsam heraus, damit es nicht reißt. 6. Vergewissern Sie sich, dass das gesamte gestaute Papier entfernt wurde.
Falls das Papier gerissen ist, kann es sein, dass noch ein Stück Papier im Gerät ist. Überprüfen Sie Folgendes und entfernen Sie ggf. das Stück Papier. • Befindet sich das Papierstück unter der FINE-Patronen-Halterung? • Ist ein kleines Papierstück im Gerät verblieben? • Befindet sich das Papierstück auf der rechten oder linken Seite (B) im Gerät? 7. Schließen Sie die Abdeckung der Papierausgabe, und legen Sie das Papier dann wieder ein. Alle Druckaufträge in der Warteschlange werden abgebrochen.
In anderen Fällen Achten Sie auf folgende Punkte: Test 1: Befinden sich Fremdkörper in der Nähe des Papierausgabeschachts? Test 2: Ist das Papier gewellt? Legen Sie das Papier nach dem Glätten ein.
1003 Ursache Kein Papier mehr im Gerät oder Papier wird nicht eingezogen. Maßnahme Legen Sie das Papier erneut ein, und drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät. Legen Sie den Papierstapel so ein, dass die Vorderkante des Papiers am hinteren Ende des vorderen Fachs anliegt.
1200 Ursache Die Abdeckung der Papierausgabe ist geöffnet. Maßnahme Schließen Sie die Abdeckung der Papierausgabe, und warten Sie einen Moment. Schließen Sie sie nicht, während Sie eine FINE-Patrone austauschen.
1202 Ursache Die Abdeckung der Papierausgabe ist geöffnet. Maßnahme Schließen Sie die Abdeckung der Papierausgabe.
1250 Ursache Das Papierausgabefach ist geschlossen. Maßnahme Öffnen Sie das Papierausgabefach, um mit dem Drucken fortzufahren.
1310 Ursache Das Papierformat ist mit dem automatischen Duplexdruck möglicherweise nicht kompatibel. Maßnahme Geeignete Mediengrößen für den automatischen Duplexdruck sind A4 und Letter. Stellen Sie sicher, dass das im Gerät eingelegte Papier das richtige Format hat. Durch Drücken der Taste Schwarz (Black) oder Farbe (Color) wird das Papier ausgeschoben, und der Druckvorgang wird auf der Vorderseite des nächsten Blatts fortgesetzt. Die Rückseite des ausgeschobenen Blatts wird nicht bedruckt.
1401 Ursache Die FINE-Patrone ist nicht eingesetzt. Maßnahme Hier wird die FINE-Patrone eingesetzt. Wenn der Fehler nicht behoben wurde, ist die FINE-Patrone möglicherweise beschädigt. Wenden Sie sich an das Service-Center.
1403 Ursache Es ist keine geeignete FINE-Patrone eingesetzt. Maßnahme Setzen Sie eine geeignete FINE-Patrone ein. Wenn der Fehler nicht behoben wurde, ist die FINE-Patrone möglicherweise beschädigt. Wenden Sie sich an das Service-Center.
1485 Ursache Es ist keine korrekte Tintenpatrone eingesetzt. Maßnahme Der Druckvorgang kann nicht ausgeführt werden, da die Tintenpatrone mit diesem Gerät nicht kompatibel ist. Setzen Sie die korrekte Tintenpatrone ein. Wenn Sie den Druckvorgang abbrechen möchten, drücken Sie die Taste Stopp (Stop) am Gerät.
1486 Ursache Die FINE-Patrone ist nicht an der korrekten Position eingesetzt. Maßnahme Jede FINE-Patrone muss an der richtigen Position eingesetzt werden.
1487 Ursache Die FINE-Patrone ist nicht an der korrekten Position eingesetzt. Maßnahme Jede FINE-Patrone muss an der richtigen Position eingesetzt werden.
1682 Ursache Die FINE-Patrone wird nicht erkannt. Maßnahme Tauschen Sie die FINE-Patrone aus. Wenn der Fehler nicht behoben wurde, ist die FINE-Patrone möglicherweise beschädigt. Wenden Sie sich an das Service-Center.
1684 Ursache Die Tintenpatrone wird nicht erkannt. Maßnahme Der Druckvorgang kann nicht ausgeführt werden, weil die Tintenpatrone unter Umständen nicht ordnungsgemäß eingesetzt oder nicht mit diesem Gerät kompatibel ist. Setzen Sie die korrekte Tintenpatrone ein. Wenn Sie den Druckvorgang abbrechen möchten, drücken Sie die Taste Stopp (Stop) am Gerät.
1686 Ursache Die Tinte ist möglicherweise aufgebraucht. Maßnahme Die Funktion zur Erkennung des Tintenstands wird deaktiviert, da der Tintenstand nicht korrekt ermittelt werden kann. Wenn Sie ohne diese Funktion weiterdrucken möchten, halten Sie die Taste Stopp (Stop) am Drucker mindestens 5 Sekunden lang gedrückt. Canon empfiehlt, nur neue Patronen von Canon zu verwenden, um eine optimale Qualität zu erzielen.
1687 Ursache Die FINE-Patrone ist nicht ordnungsgemäß eingesetzt. Maßnahme Öffnen Sie die Abdeckung der Papierausgabe. Wenn die Abdeckung für Kopf geöffnet wird, drücken Sie den Tintenpatronen-Sperrhebel nach oben, um sicherzustellen, dass die FINE-Patronen ordnungsgemäß eingesetzt sind. Schließen Sie danach die Abdeckung der Papierausgabe. Wenn der Fehler nicht behoben wurde, entfernen Sie die FINE-Patronen, und setzen Sie sie erneut ein.
1688 Ursache Die Tinte ist aufgebraucht. Maßnahme Tauschen Sie die Tintenpatrone aus und schließen Sie die Abdeckung der Papierausgabe. Wenn Sie den Druckvorgang fortsetzen möchten, halten Sie die Taste Stopp (Stop) am Drucker mindestens 5 Sekunden lang gedrückt, während die Tintenpatrone noch eingesetzt ist. Der Druckvorgang wird dann trotz fehlender Tinte fortgesetzt. Die Funktion zur Erkennung des Tintenstands wird deaktiviert. Tauschen Sie die leere Tintenpatrone sofort nach dem Druckvorgang aus.
1702 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1703 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1704 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1705 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1712 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1713 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1714 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1715 Ursache Tintenauffangbehälter ist fast voll. Maßnahme Drücken Sie die Taste Schwarz (Black) oder Farbe (Color) am Gerät, um den Druckvorgang fortzusetzen. Wenden Sie sich an das Service-Center.
1890 Ursache Möglicherweise wurde das Schutzmaterial für die FINE-Patronen-Halterung oder das Klebeband nicht von der Halterung entfernt. Maßnahme Öffnen Sie die Abdeckung der Papierausgabe, und stellen Sie sicher, dass das Schutzmaterial bzw. Klebeband von der FINE-Patronen-Halterung entfernt wurde. Wenn das Schutzmaterial oder Klebeband noch an der Halterung befestigt ist, entfernen Sie es. Schließen Sie dann die Abdeckung der Papierausgabe, und schalten Sie das Gerät wieder ein.
2100 Ursache Das Papierformat unter "Druckeinstellungen" entspricht nicht der Größe des eingelegten Papiers. Maßnahme Überprüfen Sie die Druckeinstellungen und das eingelegte Papier. Legen Sie Papier im richtigen Format ein, und drücken Sie auf dem Gerät die Taste Schwarz (Black) oder Farbe (Color). Wenn Sie den Druckvorgang abbrechen möchten, drücken Sie die Taste Stopp (Stop) am Gerät.
2101 Ursache Das Papierformat unter "Druckeinstellungen" entspricht nicht der Größe des eingelegten Papiers. Maßnahme Überprüfen Sie die Druckeinstellungen und das eingelegte Papier. Legen Sie Papier im richtigen Format ein, und drücken Sie auf dem Gerät die Taste Schwarz (Black) oder Farbe (Color). Wenn Sie den Druckvorgang abbrechen möchten, drücken Sie die Taste Stopp (Stop) am Gerät.
2102 Ursache Das Gerät hat erkannt, dass das eingelegte Papier an einer Seite ausgerichtet wurde. Maßnahme Legen Sie das Papier in die Mitte des vorderen Fachs ein, und schieben Sie die Papierführungen so weit nach innen, dass sie auf beiden Seiten am Papierstapel anliegen. Drücken Sie am Gerät die Taste Schwarz (Black) oder Farbe (Color), um die Fehlermeldung zu löschen.
2103 Ursache Das Gerät kann das Papierformat nicht erkennen. Maßnahme Drücken Sie die Taste Stopp (Stop) des Geräts, um den Fehler zu löschen, und versuchen Sie dann erneut zu drucken. Sollte dieser Fehler selbst nach dem erneuten Drucken weiterhin auftreten, stellen Sie das Gerät über das Bedienfeld, den Druckertreiber oder Remote UI so ein, dass es die Papierbreite nicht erkennt. Hinweis • Je nach Papiertyp erkennt das Gerät die Papierbreite möglicherweise nicht.
2900 Ursache Die Testseite für die Druckkopfausrichtung konnte nicht gescannt werden. Maßnahme Drücken Sie am Gerät die Taste Schwarz (Black) oder Farbe (Color), um die Fehlermeldung zu löschen. Überprüfen Sie die folgenden Punkte, und führen Sie die automatische Druckkopfausrichtung erneut durch. • Prüfen Sie, ob die Testseite für die Druckkopfausrichtung in der richtigen Position und Ausrichtung auf die Auflagefläche gelegt wurde.
2901 Ursache Der Druck des Musters für die Druckkopfausrichtung ist abgeschlossen, und das Gerät ist bereit für das Scannen der Seite. Maßnahme Fahren Sie mit dem Scannen des gedruckten Ausrichtungsmusters fort. 1. Legen Sie die Testseite für die Druckkopfausrichtung auf die Auflagefläche. Legen Sie die Testseite für die Druckkopfausrichtung mit der bedruckten Seite nach unten auf, und richten Sie die Markierung Ausrichtungsmarkierung , die sich an der oberen linken Ecke des Blattes befindet, an der aus.
4100 Ursache Die angegebenen Daten können nicht gedruckt werden. Maßnahme Wenn Sie den Inhalt von CREATIVE PARK PREMIUM drucken, bestätigen Sie die Meldung auf dem Computerbildschirm, und vergewissern Sie sich, dass alle Canon Original-FINE-Patronen richtig eingesetzt sind. Starten Sie den Druckvorgang dann erneut.
4103 Ursache Der automatische Duplexdruck kann mit der aktuellen Papierformateinstellung nicht durchgeführt werden. Maßnahme Drücken Sie am Gerät die Taste Stopp (Stop), um den Druckvorgang abzubrechen. Ändern Sie dann die Papierformateinstellung und drucken Sie erneut.
5011 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
5012 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
5100 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Brechen Sie den Druckvorgang ab, und schalten Sie das Gerät aus. Entfernen Sie dann das gestaute Papier oder das Schutzmaterial, das die Bewegung der FINE-Patronen-Halterung verhindert, und schalten Sie das Gerät anschließend wieder ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
5200 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
5400 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
5B02 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B03 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B04 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B05 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B12 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B13 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B14 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
5B15 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Wenden Sie sich an das Service-Center.
6000 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6500 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6800 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6801 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6900 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6901 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6902 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6910 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6911 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6930 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6931 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6932 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6933 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6936 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6937 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6938 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6940 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6941 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6942 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6943 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6944 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6945 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
6946 Ursache Es ist ein Druckerfehler aufgetreten. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Schließen Sie das Gerät wieder an, und schalten Sie das Gerät ein. Wenn das Problem weiterhin besteht, wenden Sie sich an das Service-Center.
B200 Ursache Es ist ein Fehler aufgetreten, der die Kontaktaufnahme mit dem Service-Center erfordert. Maßnahme Schalten Sie das Gerät aus, und ziehen Sie das Netzkabel des Geräts aus der Steckdose. Wenden Sie sich an das Service-Center.