MG2400 series Příručka online Skenování čeština (Czech)
Obsah Skenování. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Skenování z počítače. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Skenování s nástrojem IJ Scan Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Informace o nástroji IJ Scan Utility (software skeneru). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Obrazovky programu ScanGear (ovladač skeneru). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Karta Základní režim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Karta Rozšíř. režim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Nastavení vstupu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Skenování Skenování z počítače Skenování s nástrojem IJ Scan Utility Skenování z aplikačního softwaru, který používáte (program ScanGear) Užitečné informace o skenování Další metody skenování Umístění položek (při skenování z počítače) 4
Skenování z počítače Skenování s nástrojem IJ Scan Utility Skenování z aplikačního softwaru, který používáte (program ScanGear) Užitečné informace o skenování Další metody skenování Umístění položek (při skenování z počítače) 5
Skenování s nástrojem IJ Scan Utility Informace o nástroji IJ Scan Utility (software skeneru) Spuštění nástroje IJ Scan Utility Snadné skenování v režimu automatického skenování Základní Skenování fotografií Skenování dokumentů Skenování pomocí oblíbených nastavení Skenování položek větších než sklo (Sešití obrázku) Skenování většího počtu položek současně Ukládání po kontrole výsledků skenování Odesílání naskenovaných obrazů prostřednictvím e-mailu Vyjmutí textu z naskenovaných obrazů (OCR) Obrazovky nás
Informace o nástroji IJ Scan Utility (software skeneru) IJ Scan Utility je aplikace, která umožňuje snadno skenovat fotografie a dokumenty, atd. Celý proces od skenování po uložení obrazu lze provést jedním klepnutím na odpovídající ikonu na hlavní obrazovce nástroje IJ Scan Utility.
Důležité Některé funkce jsou dostupné až po instalaci nástroje My Image Garden. Poznámka Informace o nastavení aplikací určených k integraci naleznete v části „Dialogové okno Nastavení“.
Spuštění nástroje IJ Scan Utility Při spuštění nástroje IJ Scan Utility postupujte následovně: Windows 8: Na úvodní obrazovce vyberte položku IJ Scan Utility a spusťte nástroj IJ Scan Utility. Pokud se na úvodní obrazovce položka IJ Scan Utility nezobrazuje, vyberte ovládací tlačítko Hledat (Search) a zadejte řetězec „IJ Scan Utility“.
Snadné skenování v režimu automatického skenování Umožňuje snadné skenování dokumentů s automatickým rozpoznáním typu položky. Důležité Následující typy položek nemusí být naskenovány správně. V tomto případě upravte rámce pro oříznutí (oblasti skenování) v režimu zobrazení celého obrazu programu ScanGear (ovladač skeneru) a skenování zopakujte. Fotografie s bělavým pozadím Položky vytištěné na bílém papíře, ručně psané dokumenty, vizitky atd. Tenké položky Tlusté položky 1.
Chcete-li skenovat zadáním typu položky, postupujte podle informací na následujících stránkách.
Skenování fotografií Fotografie umístěné na skle můžete naskenovat s využitím nastavení vhodného pro fotografie. 1. Umístěte fotografii na sklo. Umístění položek (při skenování z počítače) 2. Spusťte nástroj IJ Scan Utility. 3. Klepněte na možnost Nastavení... (Settings...), vyberte dialogové okno Nastavení (Skenování fotografií) (Settings (Photo Scan)) a zadejte potřebnou velikost papíru, rozlišení atd. Po dokončení nastavení klepněte na tlačítko OK. 4. Klepněte na tlačítko Fotografie (Photo).
Skenování dokumentů Položky umístěné na skle můžete naskenovat s využitím nastavení vhodného pro dokumenty. 1. Umístěte položku na desku skeneru. Umístění položek (při skenování z počítače) 2. Spusťte nástroj IJ Scan Utility. 3. Klepněte na možnost Nastavení... (Settings...), vyberte dialogové okno Nastavení (Skenování dokumentů) (Settings (Document Scan)) a zadejte potřebnou velikost papíru, rozlišení atd. Po dokončení nastavení klepněte na tlačítko OK. 4. Klepněte na tlačítko Dokument (Document).
Skenování pomocí oblíbených nastavení Položky umístěné na skle skeneru můžete naskenovat s využitím dříve využitých oblíbených nastavení. Jedná se o pohodlný způsob, jak lze uložit často používané nastavení, či pro podrobné úpravy nastavení skenování. 1. Spusťte nástroj IJ Scan Utility. 2. Klepněte na možnost Nastavení... (Settings...), vyberte dialogové okno Nastavení (Uživatelské skenování) (Settings (Custom Scan)) a vyberte zdroj, rozlišení atd. Po dokončení nastavení klepněte na tlačítko OK.
Skenování položek větších než sklo (Sešití obrázku) Můžete skenovat levou a pravou polovinu položky, která je větší než sklo, a poté je spojit do jednoho obrázku. Podporovány jsou položky až do velikosti přibližně dvakrát větší, než je velikost skla. Poznámka V následující části naleznete popis skenování položky umístěné na levou stranu. 1. Spusťte nástroj IJ Scan Utility. 2. Klepněte na možnost Nastavení... (Settings...
5. Ověřte, zda je v nabídce Směr skenování (Scan Direction) vybrána možnost Skenovat zleva (Scan from Left). 6. Položku, kterou chcete zobrazit na levé části obrazovky umístěte na sklo skenovanou stranou dolů. 7. Klepněte na tlačítko Spustit skenování obrázku 1 (Start Scanning Image 1).
První položka se naskenuje a zobrazí v části 1. Poznámka Chcete-li skenování zrušit, klepněte na tlačítko Storno (Cancel). 8. Položku, kterou chcete zobrazit na pravé části obrazovky umístěte na sklo skenovanou stranou dolů. 9. Klepněte na tlačítko Spustit skenování obrázku 2 (Start Scanning Image 2).
Druhá položka se naskenuje a zobrazí v části 2. Poznámka Chcete-li skenování zrušit, klepněte na tlačítko Storno (Cancel). 10. Naskenované obrázky požadovaným způsobem upravte. S pomocí panelu nástrojů můžete obrázky otáčet, přibližovat nebo oddalovat a upravit tak jejich polohu.
Poznámka Zaškrtnutím políčka Upravit rámce pro oříznutí (Adjust cropping frames) určete oblast, kterou chcete uložit. Úpravy rámců pro oříznutí v okně Sešití obrázku Pokud chcete položku znovu naskenovat, vyberte obrázek v oblasti náhledu nebo oblasti miniatur v horní části obrazovky a klepněte na tlačítko (Odstranit). Vybraný obrázek se odstraní a vy budete moci položku znovu naskenovat. 11. Klepněte na tlačítko Uložit (Save). Sloučený obraz se uloží.
Skenování většího počtu položek současně Podle potřeby můžete skenovat dvě nebo více fotografií (malých položek) umístěné na skle současně a ukládat je poté samostatně. Důležité Následující typy položek nemusí být naskenovány správně. V tomto případě upravte rámce pro oříznutí (oblasti skenování) v režimu zobrazení celého obrazu programu ScanGear (ovladač skeneru) a skenování zopakujte. Fotografie s bělavým pozadím Položky vytištěné na bílém papíře, ručně psané dokumenty, vizitky atd.
Zobrazí se dialogové okno Nastavení. 4. Klepněte na tlačítko Uživatelské skenování (Custom Scan). 5. Vyberte nastavení Vybrat zdroj (Select Source) podle skenovaných položek.
6. V nabídce Velikost papíru (Paper Size) vyberte možnost Automatické skenování (Auto scan) a klepněte na tlačítko OK. Zobrazí se hlavní obrazovka nástroje IJ Scan Utility. Poznámka Podrobnosti o položkách nastavení v dialogovém okně Nastavení naleznete na následujících stránkách.
Dialogové okno Nastavení (Uživatelské skenování) 7. Klepněte na tlačítko Uživatelský (Custom). Více položek je naskenováno současně. Poznámka Chcete-li skenování zrušit, klepněte na tlačítko Storno (Cancel). Naskenované obrázky se uloží do složky zadané v nastavení Uložit do (Save in) v odpovídajícím dialogovém okně Nastavení, které zobrazíte klepnutím na tlačítko Nastavení... (Settings...). V každém dialogovém okně Nastavení lze provádět také některá podrobnější nastavení skenování.
Ukládání po kontrole výsledků skenování Výsledky skenování můžete zkontrolovat a následně obrázky uložit do počítače. Důležité Při skenování pomocí funkce Automaticky (Auto) nelze před uložením výsledky skenování zkontrolovat. Poznámka V následujících popisech jsou jako příklady použity obrazovky skenovaných fotografií. 1. Spusťte nástroj IJ Scan Utility. 2. Klepněte na tlačítko Nastavení... (Settings...). Zobrazí se dialogové okno Nastavení. 3. Klepněte na tlačítko Skenování fotografií (Photo Scan).
4. Zaškrtněte políčko Zkontrolovat výsledky skenování (Check scan results) a pak klepněte na tlačítko OK. Zobrazí se hlavní obrazovka nástroje IJ Scan Utility. Poznámka Podrobnosti o položkách nastavení v dialogovém okně Nastavení naleznete na následujících stránkách. Dialogové okno Nastavení (Skenování fotografií) Dialogové okno Nastavení (Skenování dokumentů) Dialogové okno Nastavení (Uživatelské skenování) Dialogové okno Nastavení (Skenování a sešití) Dialogové okno Nastavení (ScanGear) 5.
Poznámka Chcete-li skenování zrušit, klepněte na tlačítko Storno (Cancel). 6. Podle potřeby změňte pořadí obrázků nebo možnosti ukládání souborů. Pořadí obrázků nebo možnosti ukládání souborů můžete upravit v rámci dialogového okna Nastavení uložení (Save Settings). Poznámka Ve výchozím nastavení jsou zadány následující složky pro uložení.
Odesílání naskenovaných obrazů prostřednictvím emailu Naskenované obrázky můžete odesílat prostřednictvím e-mailu. Poznámka V následujících popisech jsou jako příklady použity obrazovky skenovaných fotografií. 1. Spusťte nástroj IJ Scan Utility. 2. Klepněte na tlačítko Nastavení... (Settings...). Zobrazí se dialogové okno Nastavení. 3. Klepněte na tlačítko Skenování fotografií (Photo Scan). 4.
Poznámka V rozevírací nabídce můžete vybrat e-mailové klienty, které chcete spustit. Je-li vybrána možnost Žádné (připojit ručně) (None (Attach Manually)), připojte naskenovaný a uložený obrázek k e-mailu ručně. 5. Klepněte na tlačítko OK. Zobrazí se hlavní obrazovka nástroje IJ Scan Utility.
Poznámka Podrobnosti o položkách nastavení v dialogovém okně Nastavení naleznete na následujících stránkách. Dialogové okno Nastavení (Automatické skenování) Dialogové okno Nastavení (Skenování fotografií) Dialogové okno Nastavení (Skenování dokumentů) Dialogové okno Nastavení (Uživatelské skenování) Dialogové okno Nastavení (ScanGear) 6. Klepněte na tlačítko Fotografie (Photo). Spustí se skenování. Po dokončení skenování se automaticky spustí e-mailový klient a obrázky se připojí k nové zprávě.
Vyjmutí textu z naskenovaných obrazů (OCR) Umožňuje skenování textu z časopisů a novin a jeho zobrazení v poznámkovém bloku (součástí systému Windows). Poznámka Text můžete rozpoznat při skenování prostřednictvím možností Dokument (Document), Uživatelský (Custom) nebo ScanGear. V následujících popisech jsou jako příklady použity obrazovky skenovaných dokumentů. 1. Spusťte nástroj IJ Scan Utility. 2. Klepněte na tlačítko Nastavení... (Settings...). Zobrazí se dialogové okno Nastavení. 3.
Poznámka Pokud je v okně Nastavení aplikace (Application Settings) zvolena možnost Spustit OCR (Start OCR), lze u nastavení Rozlišení (Resolution) vybrat pouze hodnoty 300 dpi a 400 dpi. 4. V nabídce Nastavení aplikace (Application Settings) vyberte možnost Spustit OCR (Start OCR) a poté vyberte aplikaci, ve které chcete výsledky zobrazit. Poznámka Je-li zadán program My Image Garden, text v obrazu je po jeho naskenování rozpoznán a zobrazí se v poznámkovém bloku (součástí systému Windows). 5.
Zobrazí se hlavní obrazovka nástroje IJ Scan Utility. Poznámka Podrobnosti o položkách nastavení v dialogovém okně Nastavení naleznete na následujících stránkách. Dialogové okno Nastavení (Skenování dokumentů) Dialogové okno Nastavení (Uživatelské skenování) Dialogové okno Nastavení (ScanGear) 6. Klepněte na tlačítko Dokument (Document). Spustí se skenování. Po dokončení skenování se naskenované obrázky uloží podle nastavení a rozpoznaný text se zobrazí ve vybrané aplikaci.
Dokumenty obsahující text s velikostí písma mimo rozsah 8 až 40 bodů (při rozlišení 300 dpi) Zešikmené dokumenty Dokumenty umístěné obráceně nebo dokumenty s textem s nesprávnou orientací (pootočené znaky) Dokumenty, které obsahují speciální písma, efekty, kurzívu nebo ručně psaný text Dokumenty s úzkými mezerami mezi řádky Dokumenty s barevným pozadím textu Dokumenty napsané ve více jazycích 33
Obrazovky nástroje IJ Scan Utility Hlavní obrazovka nástroje IJ Scan Utility Dialogové okno Nastavení Dialogové okno Nastavení (Automatické skenování) Dialogové okno Nastavení (Skenování fotografií) Dialogové okno Nastavení (Skenování dokumentů) Dialogové okno Nastavení (Uživatelské skenování) Dialogové okno Nastavení (Skenování a sešití) Dialogové okno Nastavení (ScanGear) Dialogové okno Nastavení (Obecné nastavení) Dialogové okno Nastavení formátu dat Dialogové okno Nastavení uložení Okno Sešití obrázku
Hlavní obrazovka nástroje IJ Scan Utility Při spuštění nástroje IJ Scan Utility postupujte následovně: Windows 8: Na úvodní obrazovce vyberte položku IJ Scan Utility a spusťte nástroj IJ Scan Utility. Pokud se na úvodní obrazovce položka IJ Scan Utility nezobrazuje, vyberte ovládací tlačítko Hledat (Search) a zadejte řetězec „IJ Scan Utility“.
Nastavení skenování/uložení a odezvu po skenování lze určit v dialogovém okně Nastavení (Uživatelské skenování) (Settings (Custom Scan)). • Sešití (Stitch) Zobrazí okno Sešití obrázku (Image Stitch), ve kterém můžete skenovat levou a pravou polovinu položky, která je větší než skleněná deska vaší tiskárny nebo skeneru, a poté spojit naskenované obrázky do jednoho obrázku.
Dialogové okno Nastavení V dialogovém okně Nastavení jsou k dispozici dvě karty: (Skenování z počítače) a (Obecné nastavení). Po klepnutí na kartu se zobrazení v červeném rámečku přepne a vy můžete upravit podrobné nastavení funkcí na každé z karet. Karta (Skenování z počítače) Podle potřeby můžete upravit odezvu při skenování pomocí nástroje IJ Scan Utility nebo My Image Garden.
Dialogové okno Nastavení (Automatické skenování) Klepnutím na možnost Automatické skenování (Auto Scan) na kartě (Skenování z počítače) zobrazíte dialogové okno Nastavení (Automatické skenování) (Settings (Auto Scan)). V dialogovém okně Nastavení (Automatické skenování) (Settings (Auto Scan)) můžete zadat upřesňující nastavení skenování a skenovat s automatickým zjištěním typu položky.
Uživatelský (Custom). Při výběru možnosti Automaticky (Auto) nelze řádně skenovat. Fotografie formátu A4 Textové dokumenty menší než formát 2L (127 x 178 mm) (5 x 7 palců), například stránky brožury s odříznutým hřebenem Položky vytištěné na tenkém bílém papíře Dlouhé a úzké položky, jako např. panoramatické fotografie Reflexní štítky na discích nemusí být naskenovány podle vašeho očekávání. Skenované položky je třeba na sklo umístit správně. V opačném případě se položky nemusí naskenovat správně.
- Fotografie, pohlednice, disky BD, DVD nebo CD a vizitky: JPEG - Časopisy, noviny a dokumenty: PDF Důležité Formát ukládaných souborů se může lišit v závislosti na způsobu umístění položky. Umístění položek (při skenování z počítače) Poznámka Formát dat lze změnit v nabídce Nastavení... (Settings...). • Nastavení... (Settings...
Tuto možnost vyberte, chcete-li naskenované obrázky uložit také do jiné složky, než kterou jste zadali v nabídce Uložit do (Save in). V rozevírací nabídce můžete vybrat požadovanou složku. • Připojit k e-mailu (Attach to e-mail) Tuto možnost vyberte, chcete-li odeslat e-maily s připojenými naskenovanými obrázky. V rozevírací nabídce můžete vybrat e-mailového klienta, kterého chcete spustit. • Nepouštět žádnou aplikaci (Do not start any application) Uložení do složky vybrané v nabídce Uložit do (Save in).
Dialogové okno Nastavení (Skenování fotografií) Klepnutím na možnost Skenování fotografií (Photo Scan) na kartě (Skenování z počítače) zobrazíte dialogové okno Nastavení (Skenování fotografií) (Settings (Photo Scan)). V dialogovém okně Nastavení (Skenování fotografií) (Settings (Photo Scan)) můžete zadat upřesňující nastavení skenování a skenovat položky jako fotografie.
• Velikost papíru (Paper Size) Vyberte velikost položky, kterou chcete naskenovat. Vyberete-li možnost Vlastní (Custom), otevře se okno, ve kterém můžete zadat velikost papíru. Zadejte nastavení Jednotka (Unit), poté zadejte hodnoty Šířka (Width) a Výška (Height) a nakonec klepněte na tlačítko OK. Poznámka Klepnutím na tlačítko Výchozí (Defaults) obnovíte u vybraného nastavení výchozí hodnoty. • Rozlišení (Resolution) Vyberte rozlišení položky, kterou chcete naskenovat.
Důležité Je-li v nastavení Barevný režim (Color Mode) vybrána možnost Černobíle (Black and White), nelze vybrat formát JPEG/Exif. • Nastavení... (Settings...) Klepnutím zobrazíte dialogové okno Nastavení formátu dat (Data Format Settings), ve kterém lze nastavit kvalitu ukládaných obrázků, vyhledávat soubory formátu PDF podle klíčových slov, nebo nastavit formát dat, ve kterém budou obrázky naskenované v režimu automatického skenování uloženy.
Tuto možnost vyberte, chcete-li naskenované obrázky uložit také do jiné složky, než kterou jste zadali v nabídce Uložit do (Save in). V rozevírací nabídce můžete vybrat požadovanou složku. • Připojit k e-mailu (Attach to e-mail) Tuto možnost vyberte, chcete-li odeslat e-maily s připojenými naskenovanými obrázky. V rozevírací nabídce můžete vybrat e-mailového klienta, kterého chcete spustit. • Nepouštět žádnou aplikaci (Do not start any application) Uložení do složky vybrané v nabídce Uložit do (Save in).
Dialogové okno Nastavení (Skenování dokumentů) Klepnutím na možnost Skenování dokumentů (Document Scan) na kartě (Skenování z počítače) zobrazíte dialogové okno Nastavení (Skenování dokumentů) (Settings (Document Scan)). V dialogovém okně Nastavení (Skenování dokumentů) (Settings (Document Scan)) můžete zadat upřesňující nastavení skenování a skenovat položky jako dokumenty.
Skenování časopisů: Časopis (Magazine) • Barevný režim (Color Mode) Vyberte barevný režim, ve kterém chcete předlohu skenovat. • Velikost papíru (Paper Size) Vyberte velikost položky, kterou chcete naskenovat. Vyberete-li možnost Vlastní (Custom), otevře se okno, ve kterém můžete zadat velikost papíru. Zadejte nastavení Jednotka (Unit), poté zadejte hodnoty Šířka (Width) a Výška (Height) a nakonec klepněte na tlačítko OK.
Zaškrtnutím tohoto políčka lze zvýšit ostrost textu v dokumentu nebo časopise, a tím zlepšit jeho čitelnost. Důležité V důsledku použití oprav se může barevný tón lišit od zdrojového obrazu. V takovém případě zrušte zaškrtnutí políčka a spusťte skenování. Poznámka Povolíte-li tuto funkci, skenování trvá déle než obvykle. • Zostřit obrysy (Sharpen outline) Zvýrazňuje hranice a zvyšuje ostrost obrazu.
Dokumenty, ve kterých mají řádky textu sklon větší než 10 stupňů nebo ve kterých se v jednotlivých řádcích úhel sklonu liší Dokumenty, které obsahují svislý i vodorovný text Dokumenty s příliš velkým nebo malým písmem Dokumenty s malým množstvím textu Dokumenty obsahující schémata a obrázky Rukou psaný text Dokumenty, které obsahují svislé i vodorovné čáry (tabulky) Poznámka Pokud je zapnutá možnost Korekce zešikmení textového dokumentu (Correct slanted text document), skenování trvá déle než obvykle.
Můžete vybrat možnost JPEG/Exif, TIFF, PNG, PDF nebo PDF (více stránek) (PDF (Multiple Pages)). Důležité Je-li v nastavení Barevný režim (Color Mode) vybrána možnost Černobíle (Black and White), nelze vybrat formát JPEG/Exif. Při výběru možnosti Spustit OCR (Start OCR) v nabídce Nastavení aplikace (Application Settings) nelze vybírat možnosti PDF nebo PDF (více stránek) (PDF (Multiple Pages)). • Nastavení... (Settings...
• Odeslat do aplikace (Send to an application) Tuto možnost vyberte, pokud chcete použít naskenované obrázky v podobě, v jaké se nachází v aplikaci umožňující obrázky procházet nebo organizovat. V rozevírací nabídce můžete vybrat požadovanou aplikaci. • Odeslat do složky (Send to a folder) Tuto možnost vyberte, chcete-li naskenované obrázky uložit také do jiné složky, než kterou jste zadali v nabídce Uložit do (Save in). V rozevírací nabídce můžete vybrat požadovanou složku.
Dialogové okno Nastavení (Uživatelské skenování) Klepnutím na možnost Uživatelské skenování (Custom Scan) na kartě (Skenování z počítače) zobrazíte dialogové okno Nastavení (Uživatelské skenování) (Settings (Custom Scan)). V dialogovém okně Nastavení (Uživatelské skenování) (Settings (Custom Scan)) můžete zadat upřesňující nastavení skenování a skenovat podle vašich předvoleb.
Hodnoty Barevný režim (Color Mode), Velikost papíru (Paper Size) a Rozlišení (Resolution) se také nastaví automaticky. Důležité Položky podporované možností Automaticky (Auto) jsou fotografie, pohlednice, vizitky, časopisy, noviny, dokumenty a disky BD, DVD nebo CD. Následující typy položek lze skenovat po zadání typu nebo velikosti položky. Při výběru možnosti Automaticky (Auto) nelze řádně skenovat.
Poznámka Je-li v nastavení Vybrat zdroj (Select Source) použita možnost Automaticky (Auto), je k dispozici pouze možnost Automaticky (Auto). Klepnutím na tlačítko Výchozí (Defaults) na obrazovce pro úpravu velikosti papíru obnovíte u vybraného nastavení výchozí hodnoty. • Rozlišení (Resolution) Vyberte rozlišení položky, kterou chcete naskenovat. Čím vyšší rozlišení (hodnota), tím více detailů bude v obrazu.
Důležité Pokud je v nastavení Barevný režim (Color Mode) vybrána možnost Černobíle (Black and White), Nastavení zpracování obrazu (Image Processing Settings) nebude k dispozici. • Zostřit obrysy (Sharpen outline) Zvýrazňuje hranice a zvyšuje ostrost obrazu.
• Snížit stíny podél vazby (Reduce gutter shadow) Opravuje stíny podél vazby mezi stránkami, které vznikají při skenování otevřených brožur. Poznámka K opravě stínů podél vazby při skenování položek či vybraných oblastí nestandardních velikostí použijte kartu Rozšíř. režim (Advanced Mode) nástroje ScanGear (ovladač skeneru). Podrobnosti naleznete v tématu „Oprava stínu podél vazby“ pro daný model, které lze otevřít z úvodní obrazovky dokumentu Příručka online.
Rozlišení nespadá do rozmezí 300 dpi až 600 dpi Velikost písma nespadá do rozmezí 8 až 48 bodů Dokumenty, které obsahují speciální písma, efekty, kurzívu nebo ručně psaný text Dokumenty se vzorkem na pozadí V takovém případě v dialogovém okně Zkontrolovat výsledky skenování (Check scan results) označte políčko Nastavení uložení (Save Settings) a obrázek otočte. (2) Oblast Nastavení uložení • Název souboru (File Name) Zadejte název souboru obrázku, který chcete uložit.
Zobrazí složku pro ukládání naskenovaných obrazů. Složku můžete změnit výběrem cílové složky v dialogovém okně Výběr cílové složky (Select Destination Folder), které se otevře po výběru možnosti Přidat... (Add...) v rozevírací nabídce. Ve výchozím nastavení jsou zadány následující složky pro uložení.
Tuto možnost vyberte, pokud chcete s využitím vybraného softwaru OCR text obrázku převést na textová data. V rozevírací nabídce můžete vybrat požadovanou aplikaci. • Nepouštět žádnou aplikaci (Do not start any application) Uložení do složky vybrané v nabídce Uložit do (Save in). Poznámka Vyberte aplikaci nebo složku v dialogovém okně Výběr aplikace (Select Application) nebo Výběr cílové složky (Select Destination Folder), které se otevře po výběru možnosti Přidat... (Add...) v rozevírací nabídce.
Dialogové okno Nastavení (Skenování a sešití) Klepnutím na možnost Skenování a sešití (Scan and Stitch) na kartě (Skenování z počítače) zobrazíte dialogové okno Nastavení (Skenování a sešití) (Settings (Scan and Stitch)). V dialogovém okně Nastavení (Skenování a sešití) (Settings (Scan and Stitch)) můžete zadat upřesňující nastavení skenování v případě skenování položek větších, než je sklo.
Poznámka Chcete-li potlačit efekt moaré, nastavte v nabídce Vybrat zdroj (Select Source) možnost Časopis (Magazine). • Barevný režim (Color Mode) Vyberte barevný režim, ve kterém chcete předlohu skenovat. • Rozlišení (Resolution) Vyberte rozlišení položky, kterou chcete naskenovat. Čím vyšší rozlišení (hodnota), tím více detailů bude v obrazu. Rozlišení • Nastavení zpracování obrazu (Image Processing Settings) (plus) můžete nastavit následující.
(2) Oblast Nastavení uložení • Název souboru (File Name) Zadejte název souboru obrázku, který chcete uložit. Pokud soubor uložíte, k nastavenému názvu souboru je připojeno datum a čtyři číslice ve formátu „_20XX0101_0001“. • Formát dat (Data Format) Vyberte formát dat, ve kterém chcete naskenované obrázky uložit. Můžete vybrat možnost JPEG/Exif, TIFF, PNG, PDF nebo PDF (více stránek) (PDF (Multiple Pages)).
(3) Oblast Nastavení aplikace • Otevřít v aplikaci (Open with an application) Tuto možnost vyberte, chcete-li skenované obrázky vylepšit nebo opravit. V rozevírací nabídce můžete vybrat požadovanou aplikaci. • Odeslat do aplikace (Send to an application) Tuto možnost vyberte, pokud chcete použít naskenované obrázky v podobě, v jaké se nachází v aplikaci umožňující obrázky procházet nebo organizovat. V rozevírací nabídce můžete vybrat požadovanou aplikaci.
Dialogové okno Nastavení (ScanGear) Klepnutím na možnost ScanGear na kartě (Skenování z počítače) zobrazíte dialogové okno Nastavení (ScanGear) (Settings (ScanGear)). V dialogovém okně Nastavení (ScanGear) (Settings (ScanGear)) můžete určit způsob ukládání obrázků při skenování položek spuštěním nástroje ScanGear (ovladač skeneru) a způsob odezvy po jejich uložení.
Poznámka Pokud je vybrán formát PDF nebo PDF (více stránek) (PDF (Multiple Pages)), můžete skenovat obrázky až do velikosti 9600 x 9600 pixelů. Po zaškrtnutí políčka Povolit skenování velkých obrazů (Enable large image scans) v nabídce Nastavení uložení (Save Settings), případně po výběru možnosti Spustit OCR (Start OCR) v nabídce Nastavení aplikace (Application Settings) můžete vybrat formát JPEG/Exif, TIFF nebo PNG. • Nastavení... (Settings...
• Zkontrolovat výsledky skenování (Check scan results) Zobrazí po skenování dialogové okno Nastavení uložení (Save Settings). Důležité Po zobrazení dialogového okna Nastavení v nástroji My Image Garden se tato možnost nezobrazí. (2) Oblast Nastavení aplikace • Otevřít v aplikaci (Open with an application) Tuto možnost vyberte, chcete-li skenované obrázky vylepšit nebo opravit. V rozevírací nabídce můžete vybrat požadovanou aplikaci.
Nastavení na otevřené obrazovce můžete obnovit na výchozí hodnoty.
Dialogové okno Nastavení (Obecné nastavení) Klepnutím na kartu (Obecné nastavení) zobrazíte dialogové okno Nastavení (Obecné nastavení) (Settings (General Settings)). V dialogovém okně Nastavení (Obecné nastavení) (Settings (General Settings)) můžete podle potřeby nastavit používaný produkt, omezení velikosti souboru připojeného k e-mailu, jazyk pro rozpoznávání textu v obrazech a složku, do které chcete obrazy dočasně ukládat.
• Složka pro umístění dočasných souborů (Folder to Save Temporary Files) Zobrazí složku pro dočasné ukládání obrazů. Klepnutím na tlačítko Procházet... (Browse...) vyberte cílovou složku. • Pokyny (Instructions) Otevře tuto příručku. • Výchozí (Defaults) Nastavení na otevřené obrazovce můžete obnovit na výchozí hodnoty.
Dialogové okno Nastavení formátu dat Dialogové okno Nastavení formátu dat (Data Format Settings) zobrazíte jednou z následujících operací. • Klepnutím na tlačítko Nastavení... (Settings...) v nabídce Nastavení uložení (Save Settings) na každé kartě dialogového okna Nastavení. • Klepnutím na tlačítko Nastavení... (Settings...
• Vysoká (High) Při ukládání bude soubor komprimován, což umožní snížit zatížení sítě či serveru. Poznámka Pokud je v nabídce Barevný režim (Color Mode) na kartě (Skenování z počítače) dialogového okna Nastavení vybrána možnost Černobíle (Black and White), uloží se soubory formátu PDF v kvalitě Standardní (Standard) i v případě, že je nastavena kvalita Vysoká (High).
Dialogové okno Nastavení uložení Zaškrtnutím políčka Zkontrolovat výsledky skenování (Check scan results) v nabídce Nastavení uložení (Save Settings) dialogového okna Nastavení zobrazíte po skenování dialogové okno Nastavení uložení (Save Settings). Formát dat a cílové umístění lze zadat během prohlížení miniatur výsledků skenování. Důležité Po skenování z nástroje My Image Garden se dialogové okno Nastavení uložení (Save Settings) nezobrazí.
Důležité Tlačítka operací náhledu se nezobrazí, pokud není v dialogovém okně Nastavení (ScanGear) (Settings (ScanGear)) zaškrtnuté políčko Povolit skenování velkých obrazů (Enable large image scans). (2) Oblast Výsledky skenování Zobrazuje miniatury naskenovaných obrázků. Pořadí ukládaní obrázků můžete změnit jejich přetažením. Názvy ukládaných souborů jsou uvedeny pod miniaturami. (3) Oblast Nastavení uložení • Název souboru (File Name) Zadejte název souboru obrázku, který chcete uložit.
podle klíčových slov, nebo nastavit formát dat, ve kterém budou obrázky naskenované v režimu automatického skenování uloženy. • Uložit do (Save in) Zobrazí složku pro ukládání naskenovaných obrazů. Složku můžete změnit výběrem cílové složky v dialogovém okně Výběr cílové složky (Select Destination Folder), které se otevře po výběru možnosti Přidat... (Add...) v rozevírací nabídce. Ve výchozím nastavení jsou zadány následující složky pro uložení.
Okno Sešití obrázku Klepnutím na položku Sešití (Stitch) na hlavní obrazovce nástroje IJ Scan Utility zobrazte okno Sešití obrázku (Image Stitch). Můžete skenovat levou a pravou polovinu položky, která je větší než sklo, a poté spojit obrázky do jednoho obrázku. Skenovat lze položky až přibližně dvakrát větší, než je velikost skla. (1) Tlačítka pro nastavení a ovládání (2) Panel nástrojů (3) Oblast Zobrazení miniatur (4) Oblast náhledu Poznámka Zobrazené položky se liší podle vybraného zdroje a zobrazení.
Samostatně skenuje levou a pravou polovinu položky o dvojnásobné velikosti formátu Letter. • Celé sklo x 2 (Full Platen x 2) Samostatně skenuje levou a pravou polovinu položky o dvojnásobné velikosti skla. • Směr skenování (Scan Direction) • Skenovat zleva (Scan from Left) Zobrazí první naskenovaný obrázek na levé straně. • Skenovat zprava (Scan from Right) Zobrazí první naskenovaný obrázek na pravé straně.
• Upravit rámce pro oříznutí (Adjust cropping frames) Oblast skenování lze upravit v náhledu. Jestliže není určena žádná oblast, uloží se obrázek o velikosti zvolené v nabídce Vybrat výstupní velikost (Select Output Size). Je-li určena oblast, bude naskenován a uložen pouze obrázek v rámci pro oříznutí. Úpravy rámců pro oříznutí v okně Sešití obrázku • Uložit (Save) • Uložit (Save) Uloží dva naskenované obrázky jako jeden obrázek. • Storno (Cancel) Zruší skenování Sešití (Stitch).
• (Otočit doleva) Otočí obrázek náhledu o 90 stupňů proti směru otáčení hodinových ručiček. • (Převrátit kolem svislé osy) Otočí obrázek náhledu o 180 stupňů. • (Otočit doprava) Otočí obrázek náhledu o 90 stupňů po směru otáčení hodinových ručiček. • (Otevřít příručku) Otevře tuto stránku. (3) Oblast Zobrazení miniatur • Oblast Zobrazení miniatur Zobrazuje miniatury naskenovaných obrázků. Jestliže nenaskenujete žádnou položku, oblast bude prázdná.
Obrázek se naskenuje ve směru uvedeném v nabídce Směr skenování (Scan Direction) a vedle něj se zobrazí číslo 2. • Po naskenování druhé položky klepnutím na možnost Spustit skenování obrázku 2 (Start Scanning Image 2) Zobrazí se dva naskenované obrázky.
Skenování z aplikačního softwaru, který používáte (program ScanGear) Informace o programu ScanGear (ovladač skeneru) Skenování s rozšířeným nastavením v programu ScanGear (ovladač skeneru) Spuštění programu ScanGear (ovladač skeneru) Skenování v základním režimu Skenování v rozšířeném režimu Skenování většího počtu dokumentů současně pomocí programu ScanGear (ovladač skeneru) Úpravy obrazů a nastavení barev pomocí programu ScanGear (ovladač skeneru) Obrazovky programu ScanGear (ovladač skeneru) Umístění pol
Informace o programu ScanGear (ovladač skeneru) Program ScanGear (ovladače skeneru) je software vyžadovaný pro skenování dokumentů. Umožňuje určit výslednou velikost a provést opravy obrazu při skenování dokumentů. Program ScanGear lze spustit z aplikace My Image Garden nebo z nástroje IJ Scan Utility. Program lze také spustit z jiných aplikací, které jsou kompatibilní se standardním rozhraním s názvem TWAIN. (Program ScanGear je ovladač kompatibilní s rozhraním TWAIN.
Rozšířený režim V režimu Rozšíř. režim (Advanced Mode) můžete při skenování zadat režim barev, výstupní rozlišení, jas obrazu, barevný tón a další možnosti.
Skenování s rozšířeným nastavením v programu ScanGear (ovladač skeneru) Spuštění programu ScanGear (ovladač skeneru) Spuštění programu ScanGear (ovladač skeneru) Skenování dokumentů po provedení jednoduchých oprav obrazu Skenování v základním režimu Skenování dokumentů po provedení rozšířených oprav obrazu a nastavení jasu nebo barvy Skenování v rozšířeném režimu Skenování více dokumentů současně po provedení oprav obrazu a nastavení barvy Skenování většího počtu dokumentů současně pomocí programu ScanGear
Spuštění programu ScanGear (ovladač skeneru) Použití programu ScanGear (ovladač skeneru) k opravám obrazu nebo nastavení barev při skenování. Program ScanGear lze spustit z aplikace My Image Garden nebo z aplikace. Spuštění z aplikace My Image Garden Při spuštění programu ScanGear z aplikace My Image Garden postupujte následovně. 1. Spusťte aplikaci My Image Garden. Podrobnosti o spuštění aplikace My Image Garden, najdete v dokumentu Příručka pro My Image Garden. 2.
Skenování v základním režimu Na kartě Základní režim (Basic Mode) lze snadno skenovat podle následujících zobrazených kroků. Informace o skenování více dokumentů současně naleznete v části „Skenování většího počtu dokumentů současně pomocí programu ScanGear (ovladač skeneru)“. Důležité Následující typy dokumentů nelze naskenovat správně. V takovém případě přepněte (Miniatura) na panelu nástrojů do zobrazení celého snímku a klepnutím na ikonu spusťte skenování.
Poznámka Chcete-li skenovat časopisy, které obsahují mnoho barev, vyberte možnost Časopis (barevný) (Magazine (Color)). 3. Klepněte na tlačítko Náhled (Preview). V oblasti náhledu se zobrazí náhled obrazu. Poznámka Barvy jsou upraveny na základě typu dokumentu, který byl zvolen v nastavení Vybrat zdroj (Select Source). 4. Nastavte Cílové umístění (Destination). 5. Nastavte Výstupní velikost (Output Size) podle zamýšleného účelu.
Možnosti výstupní velikosti se mohou lišit v závislosti na položce vybrané v nastavení Cílové umístění (Destination). 6. Dle potřeby upravte rámce pro oříznutí (oblasti skenování). V náhledu upravte velikost a polohu rámců pro oříznutí. Úpravy rámce pro oříznutí (program ScanGear) 7. Nastavte možnost Opravy obrazu (Image corrections) požadovaným způsobem. 8. Klepněte na tlačítko Skenovat (Scan). Spustí se skenování.
Skenování v rozšířeném režimu V režimu Rozšíř. režim (Advanced Mode) můžete při skenování zadat režim barev, výstupní rozlišení, jas obrazu, barevný tón a další možnosti. Informace o skenování více dokumentů současně naleznete v části „Skenování většího počtu dokumentů současně pomocí programu ScanGear (ovladač skeneru)“. Důležité Následující typy dokumentů nelze naskenovat správně. V takovém případě přepněte (Miniatura) na panelu nástrojů do zobrazení celého snímku a klepnutím na ikonu spusťte skenování.
Poznámka Při přepnutí režimu není zachováno nastavení. 3. Nastavte možnost Nastavení vstupu (Input Settings) podle typu dokumentu nebo podle účelu. 4. Klepněte na tlačítko Náhled (Preview). V oblasti náhledu se zobrazí náhled obrazu. 5. Nastavte možnost Nastavení výstupu (Output Settings). 6. Upravte požadovaným způsobem rámec pro oříznutí (oblast skenování), opravte obrázek a upravte barvy. Úpravy rámce pro oříznutí (program ScanGear) Nastavení obrazu Nastavení barev 7.
Odezvu programu ScanGear po skenování lze určit v nabídce Stav dialogového okna ScanGear po skenování (Status of ScanGear dialog after scanning) na kartě Skenovat (Scan) v dialogovém okně Předvolby (Preferences). Příbuzné téma Karta Rozšíř.
Skenování většího počtu dokumentů současně pomocí programu ScanGear (ovladač skeneru) Pomocí možností na kartách Základní režim (Basic Mode) a Rozšíř. režim (Advanced Mode) můžete skenovat dvě nebo více fotografií (malých dokumentů) na skle skeneru současně. Tato část popisuje postup při skenování většího počtu dokumentů na kartě Základní režim (Basic Mode). Důležité Chcete-li naskenovat více dokumentů do jednoho obrázku, spusťte skenování v režimu zobrazení celého snímku.
2. Nastavte hodnotu pole Vybrat zdroj (Select Source) podle dokumentu umístěného na sklo skeneru. 3. Klepněte na tlačítko Náhled (Preview). V oblasti náhledu se zobrazí miniatury náhledů obrázků. Rámce pro oříznutí se určí automaticky podle velikosti dokumentu. 4. Nastavte Cílové umístění (Destination). 5. Nastavte Výstupní velikost (Output Size) podle zamýšleného účelu. 6. Rámce pro oříznutí dle potřeby upravte a nastavte Opravy obrazu (Image corrections).
Poznámka Aplikace umožňuje opravu každého obrázku zvlášť. Vyberte snímek, který chcete opravit. V režimu zobrazení miniatur lze pro každý obraz zadat pouze jeden rámec pro oříznutí. Chcete-li vytvořit více rámců pro oříznutí v rámci jednoho obrázku, spusťte skenování v režimu zobrazení celého snímku. Skenování více dokumentů současně v režimu zobrazení celého snímku 7. Vyberte obrázky, které chcete naskenovat. Zaškrtněte obrázky, které chcete naskenovat. 8. Klepněte na tlačítko Skenovat (Scan).
Poznámka Při zobrazení celého obrázku se ikona změní na (Celý snímek). 2. Nastavte Cílové umístění (Destination). 3. Nastavte Výstupní velikost (Output Size) podle zamýšleného účelu. MožnostPřevrátit poměr stran (Invert aspect ratio) bude dostupná, pokud bude volba Výstupní velikost (Output Size) nastavena na jakoukoli možnost kromě Proměnlivá (Flexible). Klepnutím na toto tlačítko otočíte rámec pro oříznutí. Klepnete-li na tlačítko znovu, vrátí se rámec do původní orientace. 4.
Poznámka Odezvu programu ScanGear po skenování lze určit v nabídce Stav dialogového okna ScanGear po skenování (Status of ScanGear dialog after scanning) na kartě Skenovat (Scan) v dialogovém okně Předvolby (Preferences).
Úpravy obrazů a nastavení barev pomocí programu ScanGear (ovladač skeneru) Zaostření rozostřených fotografií, odstranění stop prachu a škrábanců a opravy vybledlých barev Opravy obrazu (Zaostřit s maskou, Zeslabit prach a škrábance, Oprava vyblednutí atd.
Opravy obrazu (Zaostřit s maskou, Zeslabit prach a škrábance, Oprava vyblednutí atd.) Funkce Nastavení obrazu (Image Settings) na kartě Rozšíř. režim (Advanced Mode) programu ScanGear (ovladač skeneru) vám při skenování obrazů umožňují vylepšit obrysy předmětů, zeslabit prach a škrábance a opravit vybledlé barvy. Položky nastavení Klepněte na tlačítko (šipka) u příslušné funkce a vyberte z rozevírací nabídky požadovanou položku.
Nastavení jasu a barevného tónu obrazu Podle typu dokumentu nastavte Nastavení obrazu (Image Adjustment) na Automaticky (Auto), Fotografie (Photo), Časopis (Magazine) nebo Dokument (Document). Žádné (None) Automaticky (Auto) Snížení průhlednosti textových dokumentů nebo zesvětlení základní barvy u dokumentů z recyklovaného papíru, novin atd. při skenování dokumentů Nastavte položku Snížit průhlednost (Reduce Show-through) na hodnotu ZAPNUTO (ON).
Poznámka Tištěné fotografie a obrázky se zobrazují jako soubor drobných teček. „Moaré“ je jev, při kterém se objeví nerovnoměrné přechody nebo proužky při skenování fotografií nebo obrázků vytištěných pomocí polotónového rastru. K odstranění tohoto jevu lze použít možnost Funkce Descreen (Descreen). Zeslabení prachu a škrábanců Podle stupně zaprášení nebo poškrábání nastavte funkci Zeslabit prach a škrábance (Reduce Dust and Scratches) na úroveň Nízký (Low), Střední (Medium) či Vysoký (High).
Oprava stínů mezi stránkami, které vznikají při skenování otevřených brožur Podle míry stínu nastavte funkci Oprava stínu podél vazby (Gutter Shadow Correction) na úroveň Nízký (Low), Střední (Medium) či Vysoký (High).
Úpravy barev pomocí barevného vzorku Pomocí funkce barevného vzorku na kartě Základní režim (Basic Mode) v programu ScanGear (ovladač skeneru) si můžete zobrazit náhled změn barev a reprodukovat přirozené barvy. Nastavení barev Opravte barvy, které vybledly působením času nebo vyprchání barev. Vyprchání barev je úkaz, který vzniká po celé fotografii vlivem počasí nebo silného okolního zabarveného světla. V rámečku Nastavení barev (Color Adjustment) klepněte na šipku barvy, kterou chcete zdůraznit.
Azurová a červená, purpurová a zelená a žlutá a modrá jsou komplementární dvojice barev (smísením každé dvojice barev vznikne odstín šedé). Přirozené barvy obrazu lze reprodukovat potlačením zobrazené barvy a zesílením komplementární barvy. Doporučený postup je najít místo obrazu, které má být bílé, a upravit barvy tak, aby skutečně bylo bílé. Náhled obrazu bude zobrazen uprostřed. Barvy náhledu obrazu se změní tak, jak je upravíte. Následuje příklad opravy namodralého obrazu.
Nastavení sytosti a vyvážení barev V programu ScanGear (ovladač skeneru) na kartě Rozšíř. režim (Advanced Mode) klepněte na tlačítko (sytost a vyvážení barev). Poznámka Původní nastavení v aktuálním okně vrátíte klepnutím na tlačítko Výchozí (Defaults). Sytost Slouží k úpravě sytosti (živosti) obrazu. Lze ji použít například k rozjasnění barev, které vybledly působením času.
Vyvážení barev Slouží k úpravě obrazů, jejichž barvy vyprchaly. Vyprchání barev je úkaz, který vzniká po celé fotografii vlivem počasí nebo silného okolního zabarveného světla. Posunutím jezdce u atributu Vyvážení barev (Color Balance) doleva nebo doprava dojde ke zvýraznění příslušné barvy. Azurová a Červená Purpurová a Zelená Žlutá a Modrá Jedná se o komplementární dvojice barev (smísením každé dvojice barev vznikne odstín šedé).
Nastavení jasu a kontrastu V programu ScanGear (ovladač skeneru) na kartě Rozšíř. režim (Advanced Mode) klepněte na tlačítko (jas a kontrast). Poznámka Klepnutím na tlačítko (šipka dolů) přepnete na detailní zobrazení. Klepnutím na tlačítko (šipka nahoru) se vrátíte k předchozímu zobrazení. Původní nastavení v aktuálním okně vrátíte klepnutím na tlačítko Výchozí (Defaults). Kanál Každá tečka obrazu je směsí červené, zelené a modré barvy v různých poměrech (přechod).
• Modrá (Blue) Slouží k úpravě kanálu modré barvy. Poznámka Je-li Barevný režim (Color Mode) nastaven na možnost Stupně šedi (Grayscale), budou v okně Kanál (Channel) zobrazeny pouze Stupně šedi (Grayscale). Jas Slouží k úpravě jasu obrazu. Přesunutím jezdce u atributu Jas (Brightness) doleva obraz ztmavíte, přesunutím doprava obraz rozjasníte. Lze také zadat hodnotu v rozmezí od -127 do 127. Ztmaveno Původní obraz Rozjasněno Poznámka Pokud obraz příliš zjasníte, může se ztratit zvýraznění světel.
Poznámka Zvýšením kontrastu dodáte jemným obrazům pocit trojrozměrnosti. Zvýšíte-li však kontrast příliš, mohou se ztratit světla a stíny.
Nastavení histogramu V programu ScanGear (ovladač skeneru) na kartě Rozšíř. režim (Advanced Mode) klepněte na tlačítko (histogram). Poznámka Původní nastavení v aktuálním okně vrátíte klepnutím na tlačítko Výchozí (Defaults). Kanál Každá tečka obrazu je směsí červené, zelené a modré barvy v různých poměrech (přechod). Tato barvy lze samostatně upravit jako „kanál“. • Vzor (Master) Slouží ke společné úpravě kanálu červené, zelené a modré barvy. • Červená (Red) Slouží k úpravě kanálu červené barvy.
Čtení histogramů Histogram lze zobrazit v určené oblasti pro každý Kanál (Channel). Čím vyšší má histogram špičku, tím více dat je distribuováno do dané úrovně. (1) Jasná oblast (2) Tmavá oblast (3) Celý obraz Většina dat je na straně Většina dat je na straně Data jsou rozprostřena mezi světla. stínu. oblast světla a stínu.
Karta Základní režim Tento režim umožňuje snadné skenování podle pokynů na obrazovce. Tato část popisuje nastavení a funkce, které jsou k dispozici na kartě Základní režim (Basic Mode). (1) Tlačítka pro nastavení a ovládání (2) Panel nástrojů (3) Oblast náhledu Poznámka Zobrazené položky se liší v závislosti na typu dokumentu a zobrazení. (1) Tlačítka pro nastavení a ovládání • Vybrat zdroj (Select Source) • Fotografie (barevná) (Photo (Color)) Skenování barevných fotografií.
Poznámka Vyberete-li typ dokumentu, aktivuje se funkce zaostření s maskou. Aktivuje se také funkce nastavení obrazu, která upravuje obrazy podle typu dokumentu. Vyberete-li možnost Časopis (barevný) (Magazine (Color)), funkce Descreen bude aktivní. • Zobrazit obraz v náhledu (Display Preview Image) • Náhled (Preview) Zahájí předběžné skenování. Poznámka Při prvním použití zařízení se automaticky spustí kalibrace skeneru. Chvíli vyčkejte, než se zobrazí náhled obrazu.
Možnosti výstupní velikosti se mohou lišit v závislosti na položce vybrané v nastavení Cílové umístění (Destination). • Proměnlivá (Flexible) Umožňuje vám libovolně nastavit rámce pro oříznutí (oblasti skenování). V režimu zobrazení miniatur Rámec pro oříznutí zobrazíte přetažením kurzoru přes miniaturu. Pokud je zobrazen rámec pro oříznutí, bude skenována část uvnitř rámce pro oříznutí. Není-li zobrazen žádný rámec pro oříznutí, každý snímek bude naskenován samostatně.
Chcete-li přidat velikost, zadejte parametry Název výstupní velikosti (Output Size Name), Šířka (Width) a Výška (Height) a pak klepněte na tlačítko Přidat (Add). V poli Jednotka (Unit) můžete vybrat nastavení palce (inches) nebo mm, je-li v poli Cílové umístění (Destination) nastavena hodnota Tisk (Print), ale nastavení pixely (pixels) můžete vybrat pouze v případě, že je v poli Cílové umístění (Destination) nastavena hodnota Zobrazení obrazu (Image display).
• Opravy obrazu (Image corrections) Umožňuje použít na obrazech opravy. Důležité Je-li na kartě Nastavení barev (Color Settings) v dialogovém okně Předvolby (Preferences) vybrána možnost Doporučeno (Recommended), jsou k dispozici funkcePoužít Automatickou opravu dokumentů (Apply Auto Document Fix) a Opravit vyblednutí (Correct fading). Poznámka Dostupné funkce se mění v závislosti na typu dokumentu vybraném v okně Vybrat zdroj (Select Source).
• Provést skenování (Perform Scan) • Skenovat (Scan) Spustí se skenování. Poznámka Po zahájení skenování se zobrazí průběh skenování. Chcete-li skenování zrušit, klepněte na tlačítko Storno (Cancel). • Předvolby... (Preferences...) Otevře se dialogové okno Předvolby (Preferences), ve kterém lze podrobněji nastavit skenování a náhled. • Zavřít (Close) Ukončí program ScanGear (ovladač skeneru). (2) Panel nástrojů • Panel nástrojů Můžete upravovat nebo otáčet obrazy v náhledu.
• (Automatické oříznutí) Zobrazení a automatické úpravy rámce pro oříznutí podle velikosti dokumentu zobrazeného v oblasti náhledu. Oblast skenování se zmenší při každém klepnutí na toto tlačítko v případě, že je oblast v rámci možné oříznout. • (Vybrat všechny snímky) Tento prvek je dostupný v případě, že jsou zobrazeny dva a více rámců. Zaškrtne políčka u snímku v zobrazení miniatur. • (Zrušit výběr všech snímků) Tento prvek je dostupný v případě, že jsou zobrazeny dva a více rámců.
Je-li na panelu nástrojů zobrazena ikona (miniatura) Podle velikosti dokumentu se určí rámce pro oříznutí a zobrazí se miniatury naskenovaných obrazů. Budou naskenovány pouze zaškrtnuté obrazy. Poznámka Je-li zobrazen náhled více obrazů, je jejich výběr naznačen různým vzhledem obrysů. Zaměřený rámec (tlustý modrý obrys): Budou použita zobrazená nastavení. Vybraný rámec (tenký modrý obrys): Tato nastavení budou použita současně pro zaměřený rámec a vybrané rámce.
Poznámka Na zobrazeném obrazu můžete určit rámec pro oříznutí. V režimu zobrazení miniatur lze pro každý obraz zadat pouze jeden rámec pro oříznutí. V režimu zobrazení celého snímku však můžete vytvářet více rámců pro oříznutí.
Karta Rozšíř. režim Tento režim umožňuje provést upřesňující nastavení skenování, např. režim barev, výstupní rozlišení, jas obrazu nebo barevný tón. Tato část popisuje nastavení a funkce, které jsou k dispozici na kartě Rozšíř. režim (Advanced Mode). (1) Tlačítka pro nastavení a ovládání (2) Panel nástrojů (3) Oblast náhledu Poznámka Zobrazené položky se liší v závislosti na typu dokumentu a zobrazení.
Zadejte položku Název nastavení (Setting Name) a klepněte na tlačítko Přidat (Add). Název se zobrazí v poli Seznam oblíbených nastavení (Favorite Settings List). Klepnete-li na tlačítko Uložit (Save), položka se zobrazí v seznamu Oblíbená nastavení (Favorite Settings) a lze ji vybrat, stejně jako předem definovaná nastavení. Chcete-li odstranit položku, vyberte ji v poli Seznam oblíbených nastavení (Favorite Settings List) a klepněte na tlačítkoOdstranit (Delete).
V režimu zobrazení miniatur Je-li v zobrazení miniatur zobrazeno více obrazů, klepnutím na toto tlačítko přiblížíte vybraný rámec. Chcete-li zobrazit předchozí nebo další snímek, klepněte na symbol (posunutí snímku). Poznámka Obrázek lze přiblížit také poklepáním na rámec. Dalším poklepáním na snímek lze vrátit zobrazení do stavu před zvětšením. V režimu zobrazení celého snímku Znovu naskenuje obraz v oblasti ohraničené pomocí rámce pro oříznutí při větším zvětšení.
Poznámka Po zahájení skenování se zobrazí průběh skenování. Chcete-li skenování zrušit, klepněte na tlačítko Storno (Cancel). Po dokončení skenování se může zobrazit dialogové okno, které vyzve k výběru další akce. Postup dokončete podle pokynů. Podrobnosti naleznete v tématu Stav dialogového okna ScanGear po skenování (Status of ScanGear dialog after scanning) na kartě „Karta Skenovat“ (dialogové okno Předvolby (Preferences)).
Tažením myši můžete určit oblast, která má být skenována. • (Přesunout obrázek) Pokud je obraz zvětšený v oblasti náhledu příliš velký a nevejde se na obrazovku, můžete obraz na obrazovce posouvat a zobrazit část, se kterou chcete pracovat. Obraz lze posouvat také pomocí posuvníků. • (Zvětšit/zmenšit) Umožňuje přiblížit oblast náhledu klepnutím na obraz. Klepnete-li na obraz pravým tlačítkem, zmenšíte jej. • (Otočit doleva) Otočí obrázek náhledu o 90 stupňů proti směru otáčení hodinových ručiček.
• (Odstranit rámec pro oříznutí) Odebere vybraný rámec pro oříznutí. • (Informace) Zobrazí verzi programu ScanGear a aktuální nastavení skenování (typ dokumentu atd.). • (Otevřít příručku) Otevře tuto stránku. (3) Oblast náhledu • Oblast náhledu Zde se po klepnutí na tlačítko Náhled (Preview) zobrazí náhled obrazu. Můžete si také ověřit výsledky všech nastavení (opravy obrazu, úpravy barev), která jste provedli v části „(1) Tlačítka pro nastavení a ovládání“.
Je-li na panelu nástrojů zobrazena ikona (celý snímek) Položky na skleněné desce jsou skenovány a zobrazeny jako jeden obraz. Budou naskenovány všechny části rámců pro oříznutí. Poznámka Na zobrazeném obrazu můžete určit rámec pro oříznutí. V režimu zobrazení miniatur lze pro každý obraz zadat pouze jeden rámec pro oříznutí. V režimu zobrazení celého snímku však můžete vytvářet více rámců pro oříznutí.
Nastavení vstupu Část Nastavení vstupu (Input Settings) umožňuje nastavit následující položky: • Vybrat zdroj (Select Source) Zobrazí se typ skenovaného dokumentu. • Velikost papíru (Paper Size) Vyberte velikost dokumentu, který chcete naskenovat. Toto nastavení je dostupné pouze v režimu zobrazení celého snímku. Po zadání velikosti se příslušným způsobem změní velikost oblasti náhledu. Důležité Některé aplikace mají omezený objem naskenovaných dat, který mohou přijmout.
Tento režim je vhodný pro skenování barevných dokumentů či vytváření barevných obrazů. Tento režim vykreslí obraz ve 256 úrovních (8bitová hloubka) červené (R), zelené (G) a modré barvy (B). • Stupně šedi (Grayscale) Tuto možnost vyberte při skenování černobílých fotografií nebo černobílých obrázků. Tento režim vykreslí obraz ve 256 úrovních (8bitová hloubka) černé a bílé barvy. • Černobíle (Black and White) Tento režim vyberte pro skenování fotografií a černobílých dokumentů.
Nastavení výstupu Část Nastavení výstupu (Output Settings) umožňuje nastavit následující položky: • Výstupní rozlišení (Output Resolution) Zde můžete vybrat rozlišení, ve kterém se má skenovat. Čím vyšší rozlišení (hodnota), tím více detailů bude v obrazu. Vyberte rozlišení ze zobrazených možností klepnutím na tlačítko nebo zadejte hodnotu v rozmezí 25 dpi až 19200 dpi (v přírůstcích po 1 dpi).
V režimu zobrazení celého snímku Pokud není zobrazen rámec pro oříznutí, bude skenována celá oblast náhledu. Pokud je zobrazen rámec pro oříznutí, bude skenována část uvnitř rámce pro oříznutí. Poznámka Chcete-li skenovaný obraz zvětšit nebo zmenšit, zadejte hodnoty do polí (šířka) a (výška) v části Nastavení výstupu (Output Settings) nebo zadejte hodnotu parametru % (s krokem 1 %).
případě, že je v poli Cílové umístění (Destination) nastavena hodnota Zobrazení obrazu (Image display). Název přidané velikosti se zobrazí v poli Seznam výstupních velikostí (Output Size List). Klepnutím na tlačítko Uložit (Save) uložíte položky uvedené v poli Seznam výstupních velikostí (Output Size List). Odstranit Chcete-li odstranit položku, vyberte ji v poli Seznam výstupních velikostí (Output Size List) a klepněte na tlačítkoOdstranit (Delete).
Nastavení obrazu Důležité Nepoužívejte tyto funkce na obrazy, kde nejsou vzorky moaré, prach či škrábance nebo vybledlé barvy. Může to negativně ovlivnit barevný odstín. Výsledky provedených oprav obrazu se v náhledu nemusejí projevit. Poznámka Volitelná nastavení závisí na nastavení Barevný režim (Color Mode). Pokud je zobrazeno Nastavení obrazu (Image Settings), skenování může trvat déle než obvykle.
• Časopis (Magazine) Použije úpravy obrazu vhodné pro časopisy. • Dokument (Document) Aplikuje úpravy obrazu vhodné pro textové dokumenty. Důležité Funkci Nastavení obrazu (Image Adjustment) lze nastavit po zobrazení náhledu. Toto nastavení je možné použít v případě, že je v dialogovém okně Předvolby (Preferences) na kartě Nastavení barev (Color Settings) vybrána možnost Doporučeno (Recommended). Poznámka Není-li obraz dostatečně upraven při nastavení Automaticky (Auto), vyberte typ dokumentu.
• ZAPNUTO (ON) Zvýrazňuje hranice a zvyšuje ostrost obrazu. Toto nastavení se doporučuje v běžných případech. • Funkce Descreen (Descreen) Tištěné fotografie a obrázky se zobrazují jako soubor drobných teček. „Moaré“ je jev, při kterém se objeví nerovnoměrné přechody nebo proužky při skenování fotografií nebo obrázků vytištěných pomocí polotónového rastru. K odstranění tohoto jevu lze použít možnost Funkce Descreen (Descreen). • VYPNUTO (OFF) Efekt moaré nebude snížen. • ZAPNUTO (ON) Potlačí efekt moaré.
Poznámka Při skenování tištěných materiálů doporučujeme nastavit tuto funkci na možnost Žádné (None). • Oprava vyblednutí (Fading Correction) Tato funkce se používá k opravě fotografií, které vybledly působením času nebo kvůli vyprchání barev. Vyprchání barev je úkaz, který vzniká po celé fotografii vlivem počasí nebo silného okolního zabarveného světla. • Žádné (None) Oprava vyblednutí nebude provedena. • Nízký (Low) Tuto možnost vyberte v případě, že chcete opravit slabé vyblednutí nebo vyprchání barev.
Důležité Oprava nemusí být provedena správně v případě, že je oblast skenování příliš malá. • Oprava stínu podél vazby (Gutter Shadow Correction) Pomocí této funkce lze opravit stíny mezi stránkami, které se objevují při skenování otevřených brožur. Nastavíte-li funkci Oprava stínu podél vazby (Gutter Shadow Correction), výsledek se projeví na obraze v náhledu. Před skenováním zobrazte náhled výsledku, protože výsledky se mohou lišit podle typu dokumentu a způsobu přitisknutí ke skeneru.
Způsob umístění dokumentu závisí na modelu a na tom, jaký dokument skenujete. Poznámka Pokud se z důvodu světla vnikajícího mezi dokumentem a sklem skeneru objevují v naskenovaném obrazu bílé skvrny, šmouhy nebo barevné vzory, zakryjte dokument černou látkou. Není-li stínování správně opraveno, nastavte v náhledu rámec pro oříznutí (oblast skenování).
Nastavení barev Pomocí tlačítek pro nastavení barev lze vytvářet jemné opravy barevných tónů a jasu obrazu. Lze také upravit kontrast nebo jas celého obrazu a upravit hodnoty jeho zvýraznění a stínů (histogram) nebo vyvážení (tónová křivka). Důležité Tlačítka pro úpravu barev nebudou dostupná, pokud v dialogovém okně Předvolby (Preferences) na kartě Nastavení barev (Color Settings) vyberete možnost Soulad barev (Color Matching). Poznámka Volitelná nastavení závisí na nastavení Barevný režim (Color Mode).
Nastavení jasu a kontrastu • (Histogram) Histogram umožňuje zobrazit koncentraci dat pro každou úroveň jasu obrazu. V obrazu můžete určit nejsvětlejší (zvýraznění) a nejtmavší úroveň (stínování), snížit úrovně a rozšířit střed škály odstínu obrazu. Nastavení histogramu • (Nastavení tónové křivky) Slouží k úpravě jasu obrazu výběrem typu grafu (tónové křivky), který zobrazuje vyvážení mezi vstupním a výstupním odstínem. Lze provádět jemné doladění jasu v určité oblasti.
• Uživatelský (Custom) Uživatel může pojmenovat a uložit sadu nastavení tónové křivky a prahové hodnoty tlačítek pro úpravy barev. Z rozevírací nabídky vyberte položku Přidat/odstranit... (Add/Delete...). Je-li v nastavení Barevný režim (Color Mode) vybrána jakákoliv jiná možnost než Černobíle (Black and White), otevře se dialogové okno Přidat/odstranit nastavení tónové křivky (Add/ Delete Tone Curve Settings).
Dialogové okno Předvolby Klepnutím na tlačítko Předvolby... (Preferences...) na obrazovce programu ScanGear (ovladač skeneru) otevřete dialogové okno Předvolby (Preferences). V dialogovém okně Předvolby (Preferences) můžete na kartách Skener (Scanner), Náhled (Preview), Skenovat (Scan) a Nastavení barev (Color Settings) určit rozšířené nastavení funkcí programu ScanGear.
Karta Skener Na kartě Skener (Scanner) lze určit následující nastavení. • Nastavení automatického zapínání/vypínání (Auto Power Settings) Zařízení lze nastavit tak, aby se automaticky zapínalo nebo vypínalo. Chcete-li zobrazit dialogové okno Nastavení automatického zapínání/vypínání (Auto Power Settings), klepněte na tlačítko Nastavení... (Settings...).
Funkce ztišení umožňuje snížit provozní hluk tohoto zařízení. Tuto funkci použijte, chceteli snížit provozní hluk, například při skenování nebo tisku v noci. Klepnutím na položku Nastavení... (Settings...) nastavte tichý režim. Poznámka Tichý režim můžete spustit na ovládacím panelu zařízení, v ovladači tiskárny nebo v programu ScanGear. Tento režim bude aktivní bez ohledu na způsob nastavení při použití ovládacího panelu zařízení, při tisku nebo skenování z počítače apod.
Zaškrtněte políčko Hrát hudbu při skenování (Play Music During Scanning) nebo Přehrát zvuk po dokončení skenování (Play Sound When Scanning is Completed), klepněte na tlačítko Procházet... (Browse...) a vyberte zvukový soubor. Lze použít soubory následujících formátů. - Soubor MIDI (*.mid, *.rmi, *.midi) - Hudební soubor (*.wav, *.aif, *.aiff) - Soubor MP3 (*.
Karta Náhled Na kartě Náhled (Preview) lze určit následující nastavení. • Náhled při spuštění aplikace ScanGear (Preview at Start of ScanGear) Vyberte, jaká akce se provede s náhledem po spuštění programu ScanGear (ovladač skeneru). • Automatické zobrazení náhledu (Automatically Execute Preview) Program ScanGear při spuštění automaticky začne vytvářet náhled. • Zobrazit uložený náhled obrazu (Display Saved Preview Image) Zobrazí se náhled předchozího obrázku.
• Zobrazit poslední snímek obrazů v náhledu (Display the Last Frame on Previewed Images) Po zobrazení náhledu bude zobrazen rámec pro oříznutí stejné velikosti jako poslední použitý rámec. • Žádné (None) Po zobrazení náhledu se nezobrazí žádný rámec pro oříznutí. • Velikost rámce oříznutí pro zobrazení miniatur (Cropping Size for Thumbnail View) Můžete zvolit velikost oříznutí pro miniatury snímků skenovaných dokumentů.
Karta Skenovat Na kartě Skenovat (Scan) lze určit následující nastavení. • Stav dialogového okna ScanGear po skenování (Status of ScanGear dialog after scanning) Vyberte, jaká akce se provede s programem ScanGear (ovladač skeneru) po naskenování obrazů. • Zavřít ovladač ScanGear automaticky (Close ScanGear automatically) Vyberete-li tuto možnost, dojde po skončení skenování k návratu do původní aplikace.
Poznámka I když vyberete možnost Nezavírat ovladač ScanGear automaticky (Do not close ScanGear automatically) nebo Zobrazit dialogové okno pro výběr další akce (Display the dialog to select next action), nemusí ji některé aplikace podporovat.
Karta Nastavení barev Na kartě Nastavení barev (Color Settings) lze určit následující nastavení. • Nastavení barev Vyberte jednu z následujících možností. Tuto možnost můžete vybrat, je-li v nastavení Barevný režim (Color Mode) vybrána možnost Barevně (Color) nebo Stupně šedi (Grayscale). • Doporučeno (Recommended) Vyberte tuto možnost, pokud chcete věrně zobrazit odstín dokumentu na obrazovce. Toto nastavení se doporučuje v běžných případech.
Výběrem této možnosti zakážete opravu barev, kterou umožňuje program ScanGear (ovladač skeneru). Poznámka Funkce Soulad barev je k dispozici, jsou-li správně nastaveny program ScanGear, monitor, aplikace vhodná pro správu barev (například Adobe Photoshop) a tiskárna. Informace o nastavení monitoru, tiskárny a aplikace naleznete v příslušných příručkách. • Hodnota Gamma monitoru (Monitor Gamma) Nastavením hodnoty gamma monitoru lze upravit vstupní data podle charakteristik jasu monitoru.
Umístění položek (při skenování z počítače) Informace o umístění položek na sklo skeneru nebo tiskárny. Položky umístěte správně podle typu skenované položky. V opačném případě se položky nemusí naskenovat správně. Důležité Nepokládejte žádné předměty na kryt dokumentu. Při otevírání krytu dokumentů mohou do skeneru nebo tiskárny zapadnout předměty a způsobit tak poškození. Během skenování musí být kryt dokumentu zavřený.
Důležité Důležité Velké předlohy (například fotografie formátu A4), které nelze umístit dále od okraje nebo šipky (značky pro zarovnání) na skle, je možné uložit jako soubor PDF. Chcete-li je uložit v jiném formátu než ve formátu PDF, upřesněte při skenování datový formát. Umístění více položek Předlohy umístěte alespoň 1 cm (0,4 palce) od okrajů (oblast se šikmými proužky) skla a stejnou vzdálenost nechte i mezi položkami. Části umístěné do šrafované oblasti nelze skenovat.
Úpravy rámce pro oříznutí (program ScanGear) Oříznutí je operace, při které vyberete na obrázku oblast, kterou chcete zachovat. Zbývající část bude při skenování odstraněna. Na kartách Základní režim (Basic Mode) a Rozšíř. režim (Advanced Mode) můžete určit rámce pro oříznutí (oblasti skenování) na obrázcích zobrazených v oblasti náhledu na obrazovce. Po spuštění skenování bude každá oblast ohraničená rámcem pro oříznutí naskenována jako samostatný obrázek.
Představuje vybraný rámec pro oříznutí. K dispozici pouze v zobrazení celého obrázku. Více rámců můžete vybrat klepáním na rámce pro oříznutí při současném stisknutí klávesy Ctrl. Výstupní velikost, Korekce obrázků a další nastavení na kartě Základní režim (Basic Mode) nebo Rozšíř. režim (Advanced Mode) budou použita pro všechny vybrané rámce pro oříznutí.
Úpravy rámců pro oříznutí v okně Sešití obrázku Oříznutí je operace, při které vyberete na obrázku oblast, kterou chcete zachovat. Zbývající část bude při skenování odstraněna. V okně Sešití obrázku (Image Stitch) můžete u obrázku zobrazeného v oblasti náhledu nastavit rámec pro oříznutí.
Rozlišení Naskenovaný obraz představuje matici bodů, ve které je uložena informace o jejich jasu a barvě. Hustota těchto bodů se označuje jako „rozlišení“ a určuje množství detailů, které obrázek obsahuje. Jednotkou rozlišení je dpi (dots per inch). Dpi je počet bodů na úsečce o délce 2,5 cm (1 palce). Větší rozlišení (hodnota) znamená více detailů v obrázku, menší rozlišení (hodnota) méně detailů. Nastavení rozlišení Rozlišení lze nastavit na následujících obrazovkách.
Připojení k e-mailu Barevně, stupně šedi nebo černobíle 150 dpi Skenování textu pomocí OCR Barevně nebo ve stupních šedi 300 dpi Důležité Při dvojnásobném rozlišení se datová velikost naskenovaného obrázku zvýší čtyřikrát. Pokud je soubor příliš velký, jeho zpracování se výrazně zpomaluje a mohou nastat potíže, například s nedostatkem paměti. Nastavte minimální rozlišení, které odpovídá použití naskenovaného obrazu.
Formáty dat Při ukládání naskenovaných souborů lze zvolit formát dat. Vhodnost formátu dat je třeba volit podle toho, jak a v které aplikaci bude obrázek použit. Dostupné formáty dat se liší dle aplikace a operačního systému (Windows nebo Mac OS). Zde jsou uvedeny vlastnosti jednotlivých formátů dat obrázku. PNG (standardní přípona souborů: .png) Formát dat často využívaný na webových stránkách. Formát PNG je vhodný pro úpravy uložených obrazů. JPEG (standardní přípona souborů: .
Soulad barev Funkce „Soulad barev“ umožňuje provádět úpravy, které zajistí soulad barevných tónů u původní položky, při zobrazení na monitoru a u barevného výtisku. Na skeneru nebo tiskárně lze barevné tóny upravit následovně.
Další metody skenování Skenování pomocí ovladače WIA Skenování pomocí Ovládacích panelů (pouze v systému Windows XP) 171
Skenování pomocí ovladače WIA Položku můžete naskenovat z aplikace slučitelné s funkcí WIA (Windows Image Acquisition). WIA je model ovladače implementovaný v systému Windows XP nebo v novějších systémech. Umožňuje skenovat předlohy bez použití aplikace. Postup se liší v závislosti na používané aplikaci. Následující postupy slouží pouze jako příklady. Podrobnosti naleznete v příručce k aplikaci. Skenování pomocí ovladače WIA 2.0 Následuje příklad skenování pomocí nástroje „Fax a skener systému Windows.
• Typ souboru (File type) Vyberte formát dat z nabídky JPEG, BMP, PNG a TIFF. • Rozlišení (Resolution (DPI)) Zvolte rozlišení. Zadejte hodnotu mezi 50 dpi a 600 dpi. Rozlišení • Jas (Brightness) Pomocí jezdce upravte jas. Přesunutím jezdce doleva obraz ztmavíte, přesunutím doprava obraz zesvětlíte. Lze také zadat hodnotu v rozmezí od -100 do 100. • Kontrast (Contrast) Pomocí jezdce upravte kontrast. Přesunutím jezdce doleva se kontrast sníží, obraz se tedy zjemní.
Zvolit lze z možností Barevný obrázek (Color picture), Obrázek v odstínech šedi (Grayscale picture), Černobílý obrázek nebo text (Black and white picture or text) a Vlastní nastavení (Custom Settings). Poznámka Chcete-li pro skenování použít hodnoty dříve nastavené v dialogovém okně Úprava kvality skenovaného obrázku (Adjust the quality of the scanned picture), vyberte možnost Vlastní nastavení (Custom Settings). 4.
Skenování pomocí Ovládacích panelů (pouze v systému Windows XP) Obrazy můžete skenovat pomocí Ovládacích panelů systému Windows XP a ovladače WIA. 1. V nabídce Start vyberte příkaz Ovládací panely (Control Panel). 2. Klepněte na položku Tiskárny a jiný hardware (Printers and Other Hardware) > Skenery a fotoaparáty (Scanners and Cameras) a poklepejte na položku Canon série XXX (Canon XXX series), kde "XXX" je název modelu. Otevře se dialogové okno Průvodce skenery a fotoaparáty (Scanner and Camera Wizard).
• Jas (Brightness) Pomocí jezdce upravte jas. Přesunutím jezdce doleva obraz ztmavíte, přesunutím doprava obraz zesvětlíte. Lze také zadat hodnotu v rozmezí od -127 do 127. • Kontrast (Contrast) Pomocí jezdce upravte kontrast. Přesunutím jezdce doleva se kontrast sníží, obraz se tedy zjemní. Přesunutím jezdce doprava se kontrast zvýší a obraz bude ostřejší. Lze také zadat hodnotu v rozmezí od -127 do 127. • Rozlišení (Resolution (DPI)) Zvolte rozlišení. Zadejte hodnotu mezi 50 dpi a 600 dpi.
Umístění položek (při skenování z počítače) Informace o umístění položek na sklo skeneru nebo tiskárny. Položky umístěte správně podle typu skenované položky. V opačném případě se položky nemusí naskenovat správně. Důležité Nepokládejte žádné předměty na kryt dokumentu. Při otevírání krytu dokumentů mohou do skeneru nebo tiskárny zapadnout předměty a způsobit tak poškození. Během skenování musí být kryt dokumentu zavřený.
Důležité Důležité Velké předlohy (například fotografie formátu A4), které nelze umístit dále od okraje nebo šipky (značky pro zarovnání) na skle, je možné uložit jako soubor PDF. Chcete-li je uložit v jiném formátu než ve formátu PDF, upřesněte při skenování datový formát. Umístění více položek Předlohy umístěte alespoň 1 cm (0,4 palce) od okrajů (oblast se šikmými proužky) skla a stejnou vzdálenost nechte i mezi položkami. Části umístěné do šrafované oblasti nelze skenovat.