MG2500 series Příručka online Tisk Kopírování čeština (Czech)
Obsah Tisk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Tisk z počítače. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tisk z aplikačního softwaru, který používáte (ovladač tiskárny). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Tisk s využitím snadného nastavení. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ovladač tiskárny Canon IJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Otevření okna nastavení ovladače tiskárny. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Monitor stavu Canon IJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Kontrola stavu inkoustu z počítače. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tisk Tisk z počítače Tisk z aplikačního softwaru, který používáte (ovladač tiskárny) 4
Tisk z počítače Tisk z aplikačního softwaru, který používáte (ovladač tiskárny) 5
Tisk z aplikačního softwaru, který používáte (ovladač tiskárny) Tisk s využitím snadného nastavení Základní Různé metody tisku Změna kvality tisku a úprava obrazových dat Přehled ovladače tiskárny Popis ovladače tiskárny Aktualizace ovladačů MP Drivers Sdílení tiskárny v síti 6
Tisk s využitím snadného nastavení Tato část popisuje jednoduchý postup nastavení na kartě Rychlé nastavení, která umožňují tisk vhodný pro toto zařízení. 1. Zkontrolujte, zda je zařízení zapnuté 2. Vložte papír do zařízení 3. Otevřete okno nastavení ovladače tiskárny 4. Vyberte často používaný profil V možnostech Běžně používaná nastavení (Commonly Used Settings) na kartě Rychlé nastavení (Quick Setup) vyberte profil tisku, který je vhodný pro daný účel.
Důležité Dostupnost nastavení kvality tisku, která můžete použít, závisí na profilu tisku. 6. Dokončete nastavení Klepněte na tlačítko OK. Po spuštění tisku bude dokument vytištěn podle nastavení, které odpovídá danému účelu.
(Main) a Vzhled stránky (Page Setup) uložena všechna zadaná nastavení a příště budete moci opět tisknout podle stejných nastavení. Klepnutím na tlačítko Uložit... (Save...) v okně Běžně používaná nastavení (Commonly Used Settings) zaregistrujete zadaná nastavení.
Nastavení typu média v ovladači tiskárny Nejlepších výsledků při použití tohoto zařízení dosáhnete, pokud vyberete typ média, který nejlépe odpovídá účelu tisku. V zařízení můžete použít následující typy médií. Komerčně dostupné papíry Název média Typ média (Media Type) v ovladači tiskárny Běžný papír (včetně recyklovaného papíru) Běžný papír (Plain Paper) Obálky Obálka (Envelope) Originální papíry Canon (tisk fotografií) Typ média (Media Type) v ovladači Název média
Různé metody tisku Nastavení funkcí Velikost stránky a Orientace Nastavení počtu kopií a pořadí tisku Nastavení okraje pro sešití Tisk přizpůsobený velikosti stránky Tisk v měřítku Tisk rozvržené stránky Vedle sebe/Tisk plakátu Tisk brožury Oboustranný tisk Tisk razítka nebo pozadí Registrace razítka Registrace obrazových dat pro použití jako pozadí Nastavení tisku obálek Zobrazení výsledků tisku před tiskem Nastavení rozměrů papíru (Uživatelská velikost) Úprava tištěného dokumentu nebo přetisk z historie t
Nastavení funkcí Velikost stránky a Orientace Velikost a orientace stránky jsou přednostně určeny softwarovou aplikací. Pokud jsou v nastavení Velikost stránky (Page Size) a Orientace (Orientation) na kartě Vzhled stránky (Page Setup) hodnoty velikosti a orientace stránky stejné jako hodnoty nastavené v aplikaci, není nutné je vybírat na kartě Vzhled stránky (Page Setup).
Poznámka Je-li v nastavení Rozvržení stránky (Page Layout) vybrána možnost Normální velikost (Normal-size), zobrazí se políčko Automaticky zmenšit velikost dokumentu, který nemůže tiskárna vytisknout (Automatically reduce large document that the printer cannot output). Za normálních okolností můžete políčko Automaticky zmenšit velikost dokumentu, který nemůže tiskárna vytisknout (Automatically reduce large document that the printer cannot output) nechat zaškrtnuté.
Nastavení počtu kopií a pořadí tisku Chcete-li zadat počet kopií a pořadí tisku, postupujte takto: Počet kopií můžete také nastavit na kartě Rychlé nastavení (Quick Setup). 1. Otevřete okno nastavení ovladače tiskárny 2. Zadejte počet kopií, které se mají vytisknout Na kartě Vzhled stránky (Page Setup) v položce Počet kopií (Copies) zadejte počet kopií k vytištění. 3. Zadejte pořadí tisku Pokud chcete začít tisknout od poslední stránky, zaškrtněte políčko Tisk od poslední stránky (Print from Last Page).
• Tisk od poslední stránky (Print from Last Page): /Kompletovat (Collate): • Tisk od poslední stránky (Print from Last Page): /Kompletovat (Collate): • Tisk od poslední stránky (Print from Last Page): /Kompletovat (Collate): 4. Dokončete nastavení Klepněte na tlačítko OK. Po spuštění tisku se vytiskne zadaný počet kopií v zadaném pořadí. Důležité Pokud softwarová aplikace, pomocí které byl dokument vytvořen, obsahuje stejnou funkci, zadejte nastavení v ovladači tiskárny.
Poznámka Nastavením možností Tisk od poslední stránky (Print from Last Page) i Kompletovat (Collate) můžete tisknout tak, že jednotlivá seskupení stránek budou kompletována od poslední stránky. Tato nastavení lze použít v kombinaci s nastaveními Normální velikost (Normal-size), Přizpůsobené velikosti stránky (Fit-to-Page), V měřítku (Scaled), Rozvržení stránky (Page Layout) a Oboustranný tisk (Ručně) (Duplex Printing (Manual)).
Nastavení okraje pro sešití Chcete-li nastavit sešívanou stranu a šířku okraje, postupujte takto: 1. Otevřete okno nastavení ovladače tiskárny 2. Zadejte stranu, která má být sešita Zkontrolujte umístění okraje pro sešití na kartě Vzhled stránky (Page Setup) v nastavení Sešívaná strana (Stapling Side). Tiskárna analyzuje nastavení Orientace (Orientation) a Rozvržení stránky (Page Layout) a automaticky vybere nejlepší umístění sponky. Pokud chcete nastavení změnit, vyberte ze seznamu jinou hodnotu. 3.
Poznámka Tiskárna automaticky zmenší oblasti tisku v závislosti na velikosti okraje pro sešití. 4. Dokončete nastavení Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko OK. Při provádění tisku jsou data vytištěna se zadaným nastavením sešívané strany a šířky okraje. Důležité Možnosti Sešívaná strana (Stapling Side) a Zadat okraj... (Specify Margin...
Tisk přizpůsobený velikosti stránky Postup tisku automaticky zvětšeného nebo zmenšeného dokumentu tak, aby se přizpůsobil velikosti stránky, je následující: 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte tisk přizpůsobený velikosti stránky Ze seznamu Rozvržení stránky (Page Layout) na kartě Vzhled stránky (Page Setup) vyberte možnost Přizpůsobené velikosti stránky (Fit-to-Page). 3.
Vyberte velikost papíru vloženého do zařízení ze seznamu Velikost papíru v tiskárně (Printer Paper Size). Pokud je Velikost papíru v tiskárně (Printer Paper Size) menší než Velikost stránky (Page Size), obraz stránky bude zmenšen. Pokud je Velikost papíru v tiskárně (Printer Paper Size) větší než Velikost stránky (Page Size), obraz stránky bude zvětšen. Aktuální nastavení se zobrazí v náhledu nastavení na levé straně okna ovladače tiskárny. 5. Dokončete nastavení Klepněte na tlačítko OK.
Tisk v měřítku Chcete-li vytisknout dokument se zvětšením nebo zmenšením stránek, postupujte následovně: 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte tisk v měřítku V seznamu Rozvržení stránky (Page Layout) na kartě Vzhled stránky (Page Setup) vyberte možnost V měřítku (Scaled). 3. Vyberte velikost papíru dokumentu Pomocí nastavení Velikost stránky (Page Size) vyberte velikost stránky nastavenou v používané softwarové aplikaci. 4.
• Výběrem hodnoty v poli Velikost papíru v tiskárně (Printer Paper Size) Pokud je velikost papíru v tiskárně menší než Velikost stránky (Page Size), obraz stránky bude zmenšen. Pokud je velikost papíru v tiskárně větší než Velikost stránky (Page Size), obraz stránky bude zvětšen. • Zadejte měřítko Zadejte hodnotu přímo do pole Měřítko (Scaling). Aktuální nastavení se zobrazí v náhledu nastavení na levé straně okna ovladače tiskárny. 5.
Klepněte na tlačítko OK. Po spuštění tisku se dokument vytiskne v zadaném měřítku. Důležité Pokud aplikační software, ve kterém jste vytvořili původní dokument, obsahuje funkci tisku v měřítku, nakonfigurujte nastavení v aplikačním softwaru. Toto nastavení není potřeba konfigurovat i v ovladači tiskárny. Poznámka Volbou možnosti V měřítku (Scaled) změníte tisknutelnou oblast dokumentu.
Tisk rozvržené stránky Funkce tisku rozvržené stránky umožňuje vytisknout obraz více stránek na jeden list papíru. Při tisku rozvržené stránky postupujte takto: 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte tisk rozvržené stránky Ze seznamu Rozvržení stránky (Page Layout) na kartě Vzhled stránky (Page Setup) vyberte možnost Rozvržení stránky (Page Layout). Aktuální nastavení se zobrazí v náhledu nastavení na levé straně okna ovladače tiskárny. 3.
4. Nastavte počet a pořadí stránek, které mají být vytištěny na jeden list V případě potřeby klepněte na tlačítko Zadat... (Specify...), zadejte následující nastavení v dialogovém okně Tisk rozvržené stránky (Page Layout Printing), a klepněte na tlačítko OK. Stránky (Pages) Pokud chcete změnit počet stránek, které se mají tisknout na jeden list papíru, vyberte v seznamu požadovaný počet stránek.
Vedle sebe/Tisk plakátu Funkce tisku vedle sebe/tisku plakátu umožňuje zvětšit obrazová data, rozdělit je na několik stránek a vytisknout tyto stránky na samostatné listy papíru. Takto vytištěné stránky lze také slepit a získat tiskovinu velkého formátu, např. plakát. Při tisku vedle sebe/tisku plakátu postupujte takto: Nastavení Vedle sebe/Tisk plakátu 1. Otevřete okno nastavení ovladače tiskárny 2.
3. Vyberte požadovanou velikost papíru Vyberte velikost papíru vloženého do zařízení ze seznamu Velikost papíru v tiskárně (Printer Paper Size). Tím je dokončeno nastavení pro rozdělení dokumentu na 2 a provedení tisku vedle sebe/tisku plakátu. 4. Nastavte počet rozdělení obrazu a stránky, které se budou tisknout V případě potřeby klepněte na tlačítko Zadat... (Specify...), v dialogovém okně Vedle sebe/Tisk plakátu (Tiling/Poster Printing) zadejte následující nastavení a klepněte na tlačítko OK.
5. Dokončete nastavení Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko OK. Po spuštění tisku bude dokument rozdělen na několik stránek. Tisk pouze vybraných stránek Pokud během tisku začne docházet nebo zcela dojde inkoust, můžete opakovat tisk pouze určitých stránek následujícím postupem: 1. Nastavte rozsah stránek V náhledu nastavení v levé části karty Vzhled stránky (Page Setup) postupně klepněte na stránky, které se nemají tisknout.
Důležité Protože při tisku vedle sebe/tisku plakátu se dokument zvětší, může se stát, že výsledek tisku bude hrubý.
Tisk brožury Funkce tisku brožury umožňuje tisknout data ve tvaru vhodném pro přeložení. Data se tisknout na obě strany papíru. Tento typ tisku zaručí kompletování stránek ve správném pořadí podle jejich čísel tak, aby mohly být přeloženy a uprostřed sešity. Při tisku brožury postupujte takto: 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte tisk brožury Ze seznamu Rozvržení stránky (Page Layout) vyberte možnost Brožura (Booklet) na kartě Vzhled stránky (Page Setup).
Klepněte na tlačítko Zadat... (Specify...), v dialogovém okně Tisk brožury (Booklet Printing) určete následující nastavení a klepněte na tlačítko OK. Okraj pro sešití (Margin for stapling) Určete, na které straně má být okraj pro sešití po přeložení brožury. Vložit prázdnou stránku (Insert blank page) Chcete-li ponechat jednu stranu listu prázdnou, zaškrtněte políčko a vyberte stranu, kterou chcete ponechat prázdnou. Okraj (Margin) Zadejte šířku okraje.
Oboustranný tisk Postup pro tisk dat na obě strany papíru: Oboustranný tisk můžete také nastavit v části Další funkce (Additional Features) na kartě Rychlé nastavení (Quick Setup). 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte oboustranný tisk Na kartě Vzhled stránky (Page Setup) zaškrtněte políčko Oboustranný tisk (Ručně) (Duplex Printing (Manual)). 3.
V nabídce Orientace (Orientation) a Rozvržení stránky (Page Layout) se automaticky vybere nejlepší Sešívaná strana (Stapling Side). Pokud chcete nastavení změnit, vyberte ze seznamu jinou sešívanou stranu. 5. Nastavte šířky okraje V případě potřeby klepněte na tlačítko Zadat okraj... (Specify Margin...), nastavte šířku okraje a klepněte na tlačítko OK. 6. Dokončete nastavení Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko OK.
Tisk razítka nebo pozadí V případě použití některých ovladačů tiskárny nebo provozních prostředí nemusí být funkce Razítko (Stamp) nebo Pozadí (Background) k dispozici. Funkce Razítko (Stamp) umožňuje vytisknout text razítka nebo bitovou mapu přes data dokumentu nebo pod nimi. Můžete rovněž vytisknout datum, čas a uživatelské jméno. Funkce Pozadí (Background) umožňuje vytisknout světlý obrázek pod daty dokumentu.
Poznámka V ovladači tiskárny XPS je místo tlačítka Razítko/Pozadí... (Stamp/ Background...) k dispozici tlačítko Razítko... (Stamp...) a lze použít pouze funkci razítka. 3. Vyberte razítko Zaškrtněte políčko Razítko (Stamp) a v seznamu vyberte razítko, které chcete použít. Aktuální nastavení se zobrazí v náhledu nastavení na levé straně karty Vzhled stránky (Page Setup). 4. Nastavte podrobnosti razítka V případě potřeby zadejte následující nastavení a poté klepněte na tlačítko OK.
Razítko jen na první stránce (Stamp first page only) Zaškrtněte toto políčko, pokud chcete tisknout razítko pouze na první stránce. 5. Dokončete nastavení Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko OK. Po spuštění tisku budou data vytištěna s určeným razítkem. Tisk pozadí Na ukázku jsou připraveny dva soubory bitových map. 1. Otevřete okno nastavení ovladače tiskárny 2. Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko Razítko/ Pozadí... (Stamp/Background...
Příbuzná témata Registrace razítka Registrace obrazových dat pro použití jako pozadí 37
Registrace razítka V případě použití některých ovladačů tiskárny nebo provozních prostředí nemusí být tato funkce k dispozici. Můžete vytvořit a registrovat nové razítko. Můžete rovněž změnit a znovu zaregistrovat některá nastavení existujících razítek. Nepotřebná razítka lze kdykoli odstranit. Při registraci nového razítka postupujte takto: Registrace nového razítka 1. Otevřete okno nastavení ovladače tiskárny 2. Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko Razítko/ Pozadí...
Poznámka V ovladači tiskárny XPS je místo tlačítka Razítko/Pozadí... (Stamp/ Background...) k dispozici tlačítko Razítko... (Stamp...) a lze použít pouze funkci razítka. 3. Klepněte na tlačítko Vlastní razítko... (Define Stamp...) Otevře se dialogové okno Nastavení razítka (Stamp Settings). 4.
uživatelské jméno vytištěného objektu. Podle potřeby změňte nastavení Písmo TrueType (TrueType Font), Styl (Style), Velikost (Size) a Obrys (Outline). Po klepnutí na tlačítko Vybrat barvu... (Select Color...) lze vybrat barvu razítka. Důležité Je-li vybrána možnost Datum/čas/jméno uživatele (Date/Time/User Name), bude pole Text razítka (Stamp Text) zobrazeno šedě. • Karta Umístění (Placement) Vyberte polohu razítka v seznamu Poloha (Position).
V dialogovém okně Razítko/Pozadí (Stamp/Background) (Razítko (Stamp)) zaškrtněte políčko Razítko (Stamp). Následně ze seznamu vyberte název razítka, které chcete změnit. 2. Klepněte na tlačítko Vlastní razítko... (Define Stamp...) Otevře se dialogové okno Nastavení razítka (Stamp Settings). 3. Konfigurujte razítko a zároveň sledujte jeho náhled 4. Uložte razítko s přepsáním Na kartě Uložit nastavení (Save settings) klepněte na tlačítko Uložit s přepsáním (Save overwrite).
Registrace obrazových dat pro použití jako pozadí V případě použití některých ovladačů tiskárny nebo provozních prostředí nemusí být tato funkce k dispozici. Můžete zvolit soubor bitové mapy (.bmp) a zaregistrovat jej jako nové pozadí. Můžete rovněž změnit a zaregistrovat některá nastavení existujících pozadí. Nepotřebná pozadí lze odstranit. Při registraci obrazových dat, která mají být použita jako pozadí, postupujte takto: Registrace nového pozadí 1. Otevřete okno nastavení ovladače tiskárny 2.
Poznámka V ovladači tiskárny XPS je místo tlačítka Razítko/Pozadí... (Stamp/ Background...) k dispozici tlačítko Razítko... (Stamp...) a funkci Pozadí (Background) nelze použít. 3. Klepněte na tlačítko Vybrat pozadí... (Select Background...) Otevře se dialogové okno Nastavení pozadí (Background Settings). 4. Vyberte soubor s obrázkem, který chcete zaregistrovat jako pozadí Klepněte na tlačítko Vybrat soubor... (Select File...). Vyberte cílový rastrový soubor (.bmp) a klepněte na tlačítko Otevřít (Open).
Klepněte na kartu Uložit nastavení (Save settings), zadejte nový název do pole Název (Title) a klepněte na tlačítko Uložit (Save). Po zobrazení výzvy k potvrzení klepněte na tlačítko OK. Poznámka Na začátku a konci názvu nelze zadat mezery, tabulátory ani nové řádky. 7. Dokončete nastavení Po klepnutí na tlačítko OK se znovu otevře dialogové okno Razítko/Pozadí (Stamp/ Background). V seznamu Pozadí (Background) se zobrazí zaregistrovaný název. Změna a registrace některých nastavení pozadí 1.
Odstranění nepotřebného pozadí 1. V dialogovém okně Razítko/Pozadí (Stamp/Background) klepněte na tlačítko Vybrat pozadí... (Select Background...) Otevře se dialogové okno Nastavení pozadí (Background Settings). 2. Vyberte pozadí, které chcete odstranit Vyberte název pozadí, které chcete odstranit, ze seznamu Pozadí (Backgrounds) na kartě Uložit nastavení (Save settings) a klepněte na tlačítko Odstranit (Delete). Po zobrazení výzvy k potvrzení klepněte na tlačítko OK. 3.
Nastavení tisku obálek Používáte-li ovladač tiskárny XPS, při čtení těchto informací nahrazujte odkaz „Monitor stavu Canon IJ“ odkazem „Monitor stavu Canon IJ XPS“. Při tisku obálky postupujte takto: 1. Vložte obálku do zařízení 2. Otevřete okno nastavení ovladače tiskárny 3. Vyberte typ média V části Běžně používaná nastavení (Commonly Used Settings) na kartě Rychlé nastavení (Quick Setup) vyberte možnost Obálka (Envelope). 4.
6. Vyberte požadovanou kvalitu tisku V závislosti na požadované kvalitě vyberte v nastavení Kvalita tisku (Print Quality) možnost Vysoká (High) nebo Standardní (Standard). 7. Dokončete nastavení Klepněte na tlačítko OK. Po spuštění tisku budou data vytištěna na obálku.
Zobrazení výsledků tisku před tiskem Používáte-li ovladač tiskárny XPS, při čtení těchto informací nahrazujte odkaz „Náhled na tiskárnu Canon IJ“ odkazem „Náhled na tiskárnu Canon IJ XPS“. Výsledky tisku můžete zobrazit a zkontrolovat před vytištěním. Chcete-li zobrazit výsledný tisk před tiskem, postupujte takto: Zobrazení výsledků tisku můžete také nastavit na kartě Rychlé nastavení (Quick Setup). 1. Otevřete okno nastavení ovladače tiskárny 2.
Příbuzné téma Náhled tiskárny Canon IJ 49
Nastavení rozměrů papíru (Uživatelská velikost) Pokud nelze vybrat velikost papíru v nastavení Velikost stránky (Page Size), můžete určit výšku a šířku papíru. Taková velikost papíru se nazývá „uživatelská velikost“. Chcete-li zadat uživatelskou velikost papíru, postupujte takto: Uživatelskou velikost papíru můžete také nastavit v části Velikost papíru v tiskárně (Printer Paper Size) na kartě Rychlé nastavení (Quick Setup). 1.
4. Nastavte uživatelskou velikost papíru Vyberte Jednotky (Units) a zadejte velikost používaného papíru do polí Výška (Height) a Šířka (Width). Poté klepněte na tlačítko OK. 5. Dokončete nastavení Na kartě Vzhled stránky (Page Setup) klepněte na tlačítko OK. Po spuštění tisku budou data vytištěna podle zadané velikosti papíru.
Úprava tištěného dokumentu nebo přetisk z historie tisku Je-li použit standardní ovladač IJ, není tato funkce k dispozici. V okně Náhled na tiskárnu Canon IJ XPS můžete upravit tištěný dokument nebo načíst historii tisku dokumentů a vytisknout dokument z ní.
Klepnutím na ikonu Zpět (Undo) vrátíte právě provedenou změnu. Úprava a tisk dokumentu k tisku Tisknete-li více dokumentů nebo stránek, můžete sloučit dokumenty, změnit pořadí tisku dokumentů nebo stránek nebo odstranit dokumenty či stránky. 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte náhled Na kartě Hlavní (Main) zaškrtněte políčko Náhled před tiskem (Preview before printing). 3. Dokončete nastavení Klepněte na tlačítko OK.
Také můžete klepnutím a přetažením tisknutého dokumentu změnit pořadí tisku. • Chcete-li změnit pořadí tištěných stránek, klepněte na položku Zobrazit miniatury (View Thumbnails) v nabídce Možnosti (Option) a vyberte tištěnou stránku, kterou chcete přesunout. Potom v nabídce Upravit (Edit) vyberte možnost Přesunout stránku (Move Page) v části Stránky (Pages) a vyberte příslušnou položku. Také můžete klepnutím a přetažením tisknuté stránky změnit pořadí tisku.
Mají-li slučované dokumenty různé výstupní velikosti papíru a má být proveden oboustranný tisk nebo tisk rozvržení stránky, nemusí tiskárna u některých tištěných stránek vytvořit očekávané výsledky tisku. Před tiskem zkontrolujte náhled. V závislosti na nastavení tisku tištěného dokumentu nemusí být v okně Náhled na tiskárnu Canon IJ XPS k dispozici některé funkce. Poznámka Položku Název dokumentu (Document Name) můžete libovolně přejmenovat. 5. Spuštění tisku Klepněte na tlačítko Tisk (Print).
Změna kvality tisku a úprava obrazových dat Nastavení úrovně ve funkci Kvalita tisku (Uživatelská) Tisk barevného dokumentu monochromaticky Nastavení opravy barev Optimální fotografický tisk obrazových dat Nastavení barev v ovladači tiskárny Tisk pomocí profilů ICC Nastavení vyvážení barev Nastavení vyvážení barev pomocí barevných vzorků (ovladač tiskárny) Nastavení jasu Nastavení intenzity Nastavení kontrastu Nastavení intenzity/kontrastu pomocí barevných vzorků (ovladač tiskárny) 56
Nastavení úrovně ve funkci Kvalita tisku (Uživatelská) Úroveň kvality tisku lze nastavit v části Uživatelská (Custom). Chcete-li nastavit úroveň kvality tisku, postupujte následovně: 1. Otevřete okno nastavení ovladače tiskárny 2. Vyberte požadovanou kvalitu tisku Na kartě Hlavní (Main) vyberte v nabídce Kvalita tisku (Print Quality) možnost Uživatelská (Custom) a klepněte na tlačítko Nastavit... (Set...). Otevře se dialogové okno Uživatelská (Custom). 3.
Na kartě Hlavní (Main) klepněte na tlačítko OK. Po spuštění tisku budou obrazová data vytištěna s použitím vybrané úrovně kvality tisku. Důležité V závislosti na nastavení Typ média (Media Type) nelze některé úrovně kvality tisku vybrat.
Tisk barevného dokumentu monochromaticky Chcete-li barevný dokument vytisknout monochromaticky (jednobarevně), postupujte takto: Tisk v odstínech šedi můžete také nastavit v části Další funkce (Additional Features) na kartě Rychlé nastavení (Quick Setup). 1. Otevřete okno nastavení ovladače tiskárny 2. Nastavte tisk v odstínech šedi Na kartě Hlavní (Main) zaškrtněte políčko Tisk v odstínech šedi (Grayscale Printing). 3. Dokončete nastavení Klepněte na tlačítko OK.
se mohou barvy skutečně vytištěné lišit od barev původního obrázku. Chcete-li použít funkci tisku v odstínech šedi k vytištění dat ve formátu Adobe RGB, převeďte data pomocí vhodného softwaru do formátu sRGB. Poznámka Při zpracování funkce Tisk v odstínech šedi (Grayscale Printing) může být kromě černého inkoustu použito i malé množství barevných inkoustů.
Nastavení opravy barev Můžete zadat způsob opravy barev vhodný pro typ dokumentu, který chcete vytisknout. Ovladač tiskárny normálně upravuje barvy prostřednictvím aplikace Canon Digital Photo Color, takže data jsou tištěna pomocí odstínů, kterým dává přednost většina uživatelů. Tato metoda je vhodná pro tisk dat formátu sRGB. Chcete-li tisknout s efektivním použitím barevného prostoru obrazových dat (Adobe RGB nebo sRGB), vyberte možnost ICM (Párování profilu ICC (ICC Profile Matching)).
Klepněte na kartu Soulad (Matching), vyberte nastavení Oprava barev (Color Correction) odpovídající pro daný účel a klepněte na tlačítko OK. Párování ovladače (Driver Matching) Pomocí aplikace Canon Digital Photo Color můžete vytisknout data sRGB pomocí barevných odstínů, kterým dává přednost většina uživatelů. ICM (Párování profilu ICC (ICC Profile Matching)) Během tisku upraví barvy pomocí profilu ICC. Zadejte vstupní profil, který chcete použít. Žádné (None) Ovladač tiskárny neprovádí opravu barev.
Příbuzná témata Optimální fotografický tisk obrazových dat Nastavení barev v ovladači tiskárny Tisk pomocí profilů ICC 63
Optimální fotografický tisk obrazových dat Při tisku obrázků pořízených digitálními fotoaparáty se tóny tištěných barev někdy jeví odlišně od tónů na skutečném obrázku nebo od tónů zobrazených na monitoru. Aby se výsledky tisku co nejvíce přiblížily požadovaným tónům barev, musíte vybrat metodu tisku, která je nejvhodnější pro použitou softwarovou aplikaci nebo pro daný účel. Správa barev Zařízení, jako jsou digitální fotoaparáty, skenery, monitory nebo tiskárny, zpracovávají barvy různými způsoby.
Tisk pomocí profilů ICC Popisuje postup tisku s efektivním použitím barevného prostoru Adobe RGB nebo sRGB. Chcete-li tisknout pomocí společného barevného prostoru, je potřeba softwarovou aplikaci a ovladač tiskárny nastavit tak, aby se správa barev shodovala se vstupním profilem ICC obrazových dat. Postup nastavení ovladače tiskárny se liší v závislosti na aplikačním softwaru, který je používán k tisku.
Nastavení barev v ovladači tiskárny Zadáním funkce opravy barev v ovladači tiskárny můžete tisknout data formátu sRGB s barevnými tóny, které upřednostňuje většina uživatelů používající aplikaci Canon Digital Photo Color. Pokud tisknete pomocí aplikačního softwaru, který dokáže identifikovat profily ICC a umožňuje je určit, použijte tiskový profil ICC v aplikačním softwaru a vyberte nastavení správy barev. Postup pro nastavení barev v ovladači tiskárny: 1. Otevřete okno nastavení ovladače tiskárny 2.
upravte nastavení Jas (Brightness), Intenzita (Intensity) a Kontrast (Contrast) a poté klepněte na tlačítko OK. 5. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK. Během tisku dat bude ovladač tiskárny upravovat barvy.
Tisk pomocí profilů ICC Je-li v obrazových datech určen vstupní profil ICC, můžete efektivně tisknout za využití barevného prostoru dat (Adobe RGB nebo sRGB). Postup pro nastavení ovladače tiskárny se liší v závislosti na aplikačním softwaru, který je používán k tisku.
4. Nastavte ostatní položky V případě potřeby klepněte na kartu Nastavení barev (Color Adjustment) a upravte vyvážení barev (Azurová (Cyan), Purpurová (Magenta), Žlutá (Yellow)). Dále upravte nastavení Jas (Brightness), Intenzita (Intensity) a Kontrast (Contrast) a poté klepněte na tlačítko OK. 5. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK. Po spuštění tisku bude zařízení používat barevný prostor obrazových dat.
Klepněte na kartu Soulad (Matching) a v části Oprava barev (Color Correction) vyberte možnost ICM (Párování profilu ICC (ICC Profile Matching)). 4. Vyberte vstupní profil Vyberte nastavení Vstupní profil (Input Profile), které odpovídá barevnému prostoru obrazových dat. • Pro data formátu sRGB a pro data bez vstupního profilu ICC: Vyberte možnost Standardní (Standard). • Pro data formátu Adobe RGB: Vyberte možnost Adobe RGB (1998).
Na kartě Hlavní (Main) klepněte na tlačítko OK. Po spuštění tisku bude zařízení používat barevný prostor obrazových dat.
Nastavení vyvážení barev Tóny barev je možné upravit při tisku. Protože pomocí této funkce se nastavuje vyvážení barev výstupu změnou koncentrace inkoustu jednotlivých barev, dochází ke změně celkového vyvážení barev dokumentu. Chcete-li provést výraznou změnu vyvážení barev, použijte softwarovou aplikaci. Chcete-li provést pouze drobnou úpravu vyvážení barev, použijte ovladač tiskárny.
Otevře se dialogové okno Ruční nastavení barev (Manual Color Adjustment). 3. Nastavení vyvážení barev Pro nastavení Azurová (Cyan), Purpurová (Magenta) a Žlutá (Yellow) je k dispozici samostatný posuvník. Přesunutím posuvníku doprava dojde k zesílení příslušné barvy, posunutím doleva dojde k zeslabení příslušné barvy. Pokud například zeslabíte azurovou barvu, dojde k zesílení barvy červené. Můžete rovněž ručně zadat hodnotu propojenou s posuvníkem. Zadejte hodnotu v rozmezí od -50 do 50.
Důležité Posuvník nastavujte postupně. 4. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK. Po spuštění tisku bude dokument vytištěn s nastaveným vyvážením barev. Důležité Je-li zaškrtnuto políčko Tisk v odstínech šedi (Grayscale Printing) na kartě Hlavní (Main), vyvážení barev (Azurová (Cyan), Purpurová (Magenta), Žlutá (Yellow)) jsou zobrazena šedě a nejsou k dispozici.
Nastavení vyvážení barev pomocí barevných vzorků (ovladač tiskárny) Nastavení vyvážení barev můžete upravit podle výsledků tisku vzorku. Pokud upravíte vyvážení barev nebo intenzitu/kontrast v dokumentu, funkce tisku vzorku vytiskne výsledky nastavení v podobě seznamu spolu s hodnotami nastavení. Následující postup popisuje postup nastavení vyvážení barev podle vzorku. 1. Otevřete okno nastavení ovladače tiskárny 2.
4. Nastavení tisku vzorku Po otevření dialogového okna Tisk vzorku (Pattern Print) nastavte následující položky a poté klepněte na tlačítko OK. Nastavované parametry (Parameters to Adjust) Vyberte možnosti Azurová/Purpurová/Žlutá (Cyan/Magenta/Yellow). Důležité Je-li zaškrtnuto políčko Tisk v odstínech šedi (Grayscale Printing) na kartě Hlavní (Main), možnosti Azurová/Purpurová/Žlutá (Cyan/Magenta/Yellow) jsou zobrazeny šedě a nejsou k dispozici.
Počet vzorků (Amount of Pattern Instances) Výběrem jedné z možností Největší (Largest), Velký (Large) nebo Malý (Small) nastavte počet vytištěných vzorků. Poznámka Možnosti Největší (Largest) a Velký (Large) nelze vybrat, jsou-li zvoleny určité velikosti papíru nebo výstupní velikosti papíru. Rozdíl barev mezi vzorky (Color Variation Between Instances) Nastavte míru změny barvy mezi sousedními vzorky.
na kartě Údržba (Maintenance) vybrána možnost Pouze černá (Black Only), nastavení vyvážení barev se při tisku vzorku nepoužijí. 6. Nastavení vyvážení barev Prohledněte si vytištěný výsledek a vyberte obrázek, který se vám nejvíce líbí. Poté zadejte čísla vyvážení barev vytištěná pod obrázkem do polí Azurová (Cyan), Purpurová (Magenta) a Žlutá (Yellow) na kartě Nastavení barev (Color Adjustment).
Důležité Je-li zaškrtnuto políčko Vytisknout vzorek pro nastavení barev (Print a pattern for color adjustment) na kartě Nastavení barev (Color Adjustment), následující položky jsou zobrazeny šedě a nelze upravit jejich nastavení: • Náhled před tiskem (Preview before printing) na kartě Hlavní (Main) • Možnosti Sešívaná strana (Stapling Side) a Zadat okraj... (Specify Margin...
Nastavení jasu Při tisku můžete změnit jas všech obrazových dat. Tato funkce nemění čistě bílou ani čistě černou barvu, ale mění jas přechodových barev. Na následujícím příkladu je zobrazen výsledek tisku při změně nastavení jasu.
3. Zadejte jas Vyberte pro nastavení Jas (Brightness) možnost Světlý (Light), Normální (Normal) nebo Tmavý (Dark) a klepněte na tlačítko OK. Aktuální nastavení se zobrazí v náhledu nastavení na levé straně okna ovladače tiskárny. 4. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK. Po spuštění tisku budou data vytištěna s použitím zadané hodnoty jasu.
Nastavení intenzity Během tisku můžete zředit (zesvětlit) nebo zintenzívnit (ztmavit) barvy všech obrázkových dat. Na následujícím příkladu je zobrazen případ, kdy je zvýšením intenzity při tisku obrazových dat dosaženo zintenzívnění všech barev.
3. Nastavte intenzitu Posunutím jezdce Intenzita (Intensity) doprava barvy zintenzivníte (ztmavíte) a posunutím jezdce doleva barvy zředíte (zesvětlíte). Můžete rovněž ručně zadat hodnotu propojenou s posuvníkem. Zadejte hodnotu v rozmezí od -50 do 50. Aktuální nastavení se zobrazí v náhledu nastavení na levé straně okna ovladače tiskárny. Po nastavení všech barev klepněte na tlačítko OK. Důležité Posuvník nastavujte postupně. 4. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK.
Nastavení kontrastu Je možné upravit kontrast obrázku během tisku. Chcete-li zvýraznit rozdíly mezi světlými a tmavými částmi obrázku, zvyšte kontrast. Chcete-li naopak rozdíly mezi světlými a tmavými částmi obrázku snížit, kontrast snižte.
3. Nastavení kontrastu Posunutím posuvníku Kontrast (Contrast) doprava se kontrast zvýší, posunutím doleva se kontrast sníží. Můžete rovněž ručně zadat hodnotu propojenou s posuvníkem. Zadejte hodnotu v rozmezí od -50 do 50. Aktuální nastavení se zobrazí v náhledu nastavení na levé straně okna ovladače tiskárny. Po nastavení všech barev klepněte na tlačítko OK. Důležité Posuvník nastavujte postupně. 4. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK.
Nastavení intenzity/kontrastu pomocí barevných vzorků (ovladač tiskárny) Nastavení intenzity a kontrastu můžete upravit podle výsledků tisku vzorku. Pokud upravíte vyvážení barev nebo intenzitu/kontrast v dokumentu, funkce tisku vzorku vytiskne výsledky nastavení v podobě seznamu spolu s hodnotami nastavení. Následující postup popisuje postup nastavení intenzity a kontrastu podle vzorku. 1. Otevřete okno nastavení ovladače tiskárny 2.
4. Nastavení tisku vzorku Po otevření dialogového okna Tisk vzorku (Pattern Print) nastavte následující položky a poté klepněte na tlačítko OK. Nastavované parametry (Parameters to Adjust) Vyberte možnost Intenzita/Kontrast (Intensity/Contrast). Velikost papíru v tiskárně (Printer Paper Size) Vyberte velikost papíru pro tisk vzorku. Poznámka V závislosti na velikosti papíru vybrané na kartě Vzhled stránky (Page Setup) nemusí být některé velikosti papíru k dispozici.
Poznámka Možnosti Největší (Largest) a Velký (Large) nelze vybrat, jsou-li zvoleny určité velikosti papíru nebo výstupní velikosti papíru. Rozdíl barev mezi vzorky (Color Variation Between Instances) Nastavte míru změny barvy mezi sousedními vzorky. Poznámka Možnost Velký (Large) představuje přibližně dvojnásobek možnosti Střední (Medium), možnost Malý (Small) pak přibližně polovinu možnosti Střední (Medium). 5.
Poznámka Hodnoty intenzity a kontrastu můžete nastavit také na kartě Rychlé nastavení (Quick Setup) po klepnutí na tlačítko Tisk fotografií (Photo Printing) v části Běžně používaná nastavení (Commonly Used Settings) a zvolení možnosti Ruční úprava Barva/Intenzita (Color/Intensity Manual Adjustment) v části Další funkce (Additional Features). 7. Dokončete nastavení Na kartě Hlavní (Main) klepněte na tlačítko OK.
Příbuzná témata Nastavení vyvážení barev Nastavení vyvážení barev pomocí barevných vzorků (ovladač tiskárny) Nastavení intenzity Nastavení kontrastu 90
Přehled ovladače tiskárny Ovladač tiskárny Canon IJ Otevření okna nastavení ovladače tiskárny Monitor stavu Canon IJ Kontrola stavu inkoustu z počítače Náhled tiskárny Canon IJ Odstranění nepotřebné tiskové úlohy Pokyny k používání (ovladač tiskárny) 91
Ovladač tiskárny Canon IJ Ovladač tiskárny Canon IJ (dále označovaný jako ovladač tiskárny) je software, který je nainstalovaný v počítači a umožňuje tisk dat pomocí tohoto zařízení. Ovladač tiskárny převádí tisková data vytvořená softwarovou aplikací na data, která umí tiskárna zpracovat, a odesílá takto převedená data do tiskárny. Protože různé modely podporují různé formáty tiskových dat, potřebujete speciální verzi ovladače tiskárny pro každý z modelů.
Příbuzné téma Otevření okna nastavení ovladače tiskárny 93
Otevření okna nastavení ovladače tiskárny Okno nastavení ovladače tiskárny lze otevřít z používané aplikace nebo pomocí ikony tiskárny. Otevření okna ovladače tiskárny v aplikaci Podle níže uvedeného postupu nakonfigurujete před tiskem profil tisku. 1. V aplikačním softwaru vyberte příkaz, který slouží k tisku Obvykle pomocí příkazu Tisk (Print) v nabídce Soubor (File) otevřete dialogové okno Tisk (Print). 2.
• Používáte-li systém Windows XP, klepněte postupně na položky start -> Ovládací panely (Control Panel) -> Tiskárny a jiný hardware (Printers and Other Hardware) -> Tiskárny a faxy (Printers and Faxes). 2. Klepněte pravým tlačítkem na ikonu s názvem modelu a poté v zobrazené nabídce vyberte možnost Předvolby tisku (Printing preferences) Zobrazí se okno nastavení ovladače tiskárny.
Monitor stavu Canon IJ Používáte-li ovladač tiskárny XPS, při čtení těchto informací nahrazujte odkaz „Monitor stavu Canon IJ“ odkazem „Monitor stavu Canon IJ XPS“. Monitor stavu Canon IJ je softwarová aplikace, která zobrazuje stav zařízení a průběh tisku. Stav zařízení je oznamován pomocí obrázků, ikon a zpráv. Spuštění aplikace Monitor stavu Canon IJ Aplikace Monitor stavu Canon IJ se spouští automaticky po odeslání tiskových dat do zařízení.
V takovém případě proveďte příslušnou akci podle uvedeného postupu.
Kontrola stavu inkoustu z počítače Používáte-li ovladač tiskárny XPS, při čtení těchto informací nahrazujte odkaz „Monitor stavu Canon IJ“ odkazem „Monitor stavu Canon IJ XPS“. Podle potřeby můžete zkontrolovat zbývající hladinu inkoustu a typy kazety FINE modelu. 1. Otevřete okno nastavení ovladače tiskárny 2. Spuštění aplikace Monitor stavu Canon IJ Na kartě Údržba (Maintenance) klepněte na tlačítko Zobrazit stav tiskárny (View Printer Status).
Poznámka Dialogové okno Podrobnosti o inkoustu (Ink Details) lze také otevřít klepnutím na ikonu inkoustu v rámci monitoru stavu Canon IJ.
Náhled tiskárny Canon IJ Náhled tiskárny Canon IJ je aplikace, která ještě před tiskem zobrazí, jak bude vypadat výsledný tisk. Náhled vychází z informací, které jsou nastaveny v ovladači tiskárny a umožňuje zkontrolovat rozvržení dokumentu, pořadí tisku a počet stránek. Můžete také změnit nastavení typu média. Pokud chcete před tiskem zobrazit náhled, otevřete okno nastavení ovladače tiskárny, klepněte na kartu Hlavní (Main) a zaškrtněte políčko Náhled před tiskem (Preview before printing).
Odstranění nepotřebné tiskové úlohy Používáte-li ovladač tiskárny XPS, při čtení těchto informací nahrazujte odkaz „Monitor stavu Canon IJ“ odkazem „Monitor stavu Canon IJ XPS“. Pokud tiskárna nezačne tisknout, pravděpodobně v ní zůstala data zrušené nebo neúspěšné tiskové úlohy. Odstraňte nepotřebné tiskové úlohy pomocí aplikace Monitor stavu Canon IJ. 1. Zobrazení okna Monitor stavu Canon IJ Na hlavním panelu klepněte na tlačítko monitoru stavu. Zobrazí se okno aplikace Monitor stavu Canon IJ. 2.
Pokyny k používání (ovladač tiskárny) Na tento ovladač tiskárny se vztahují následující omezení. Při používání ovladače tiskárny mějte na paměti následující body. Omezení ovladače tiskárny • Při použití některých aplikací nemusí být na kartě Vzhled stránky (Page Setup) v ovladači tiskárny dostupné nastavení Počet kopií (Copies). V takovém případě použijte nastavení počtu kopií v dialogovém okně Tisk (Print) softwarové aplikace.
• V některých aplikacích je tisk rozdělen do několika tiskových úloh. Chcete-li tisk zrušit, odstraňte všechny dílčí tiskové úlohy. • Pokud se obrazová data nevytiskla správně, zobrazte na kartě Vzhled stránky (Page Setup) dialogové okno Možnosti tisku (Print Options) a změňte nastavení Vypnout ICM - vyžadováno aplikací (Disable ICM required from the application software). Tím se může problém vyřešit.
7. Spusťte tisk. • Je-li v aplikaci Adobe Illustrator (Adobe Systems Incorporated) povolena funkce tisku bitové mapy, může tisk trvat delší dobu nebo nemusí být vytištěna některá data. Zkuste tisk opakovat po zrušení zaškrtnutí možnosti Tisk bitové mapy (Bitmap Printing) v dialogovém okně Tisk (Print).
Popis ovladače tiskárny Popis karty Rychlé nastavení Popis karty Hlavní Popis karty Vzhled stránky Popis karty Údržba Popis aplikace Náhled na tiskárnu Canon IJ Popis aplikace Náhled na tiskárnu Canon IJ XPS Popis dialogového okna Monitor stavu Canon IJ 105
Popis karty Rychlé nastavení Karta Rychlé nastavení (Quick Setup) slouží k registraci běžně používaných nastavení tisku. Pokud vyberete zaregistrované nastavení, zařízení se automaticky přepne na přednastavené položky. Běžně používaná nastavení (Commonly Used Settings) Jsou zaregistrovány názvy a ikony často používaných profilů tisku. Pokud vyberete profil tisku podle účelu použití dokumentu, použijí se nastavení odpovídající tomuto účelu.
Obchodní dokument (Business Document) Toto nastavení vyberte při tisku obecného dokumentu. Pokud položky Velikost stránky (Page Size), Orientace (Orientation) a Počet kopií (Copies) nastavíte v aplikaci, mají tato nastavení přednost. Úspora papíru (Paper Saving) Toto nastavení vyberte, chcete-li při tisku obecného dokumentu šetřit papír. Políčka Tisk 2-na-1 (2-on-1 Printing) a Oboustranný tisk (Ručně) (Duplex Printing (Manual)) se zaškrtnou automaticky.
Možnosti... (Options...) Otevře Dialogové okno Uložit běžně používaná nastavení (Save Commonly Used Settings). Změní podrobnosti profilu tisku, který má být uložen. Dialogové okno Uložit běžně používaná nastavení (Save Commonly Used Settings) Vyberte, aby tyto ikony profilu tisku byly registrovány v seznamu Běžně používaná nastavení (Commonly Used Settings), a změňte položky, které mají být uloženy v profilech tisku. Ikona (Icon) Vyberte ikonu profilu tisku, který chcete uložit.
(Copies). Tiskárna místo toho tiskne s nastavením kopií zadaným pomocí aplikace. Odstranit (Delete) Odstraní zaregistrovaný profil tisku. V seznamu Běžně používaná nastavení (Commonly Used Settings) vyberte název nastavení, které chcete odstranit, a klepněte na tlačítko Odstranit (Delete). Když se zobrazí žádost o potvrzení, klepnutím na tlačítko OK zadaný profil tisku odstraňte. Poznámka Profily tisku registrované v počátečním nastavení nelze odstranit.
okno Tisk rozvržené stránky (Page Layout Printing) můžete upřesnit nastavení Pořadí stránek (Page Order). Tisk 4-na-1 (4-on-1 Printing) Vytiskne čtyři stránky příslušného dokumentu vedle sebe na jeden list papíru. Chcete-li změnit posloupnost stránek, klepněte na kartu Vzhled stránky (Page Setup), pro položku Rozvržení stránky (Page Layout) vyberte možnost Rozvržení stránky (Page Layout) a klepněte na tlačítko Zadat... (Specify...).
Velikost papíru v tiskárně (Printer Paper Size) Vybere velikost papíru právě vloženého do zařízení. Velikost papíru se za normálních podmínek nastavuje automaticky podle nastavení výstupní velikosti papíru a dokument je vytištěn bez změny měřítka. Pokud v položce Další funkce (Additional Features) nastavíte možnost Tisk 2-na-1 (2on-1 Printing) nebo Tisk 4-na-1 (4-on-1 Printing), lze velikost papíru nastavit ručně pomocí položky Velikost stránky (Page Size) na kartě Vzhled stránky (Page Setup).
Kvalita tisku (Print Quality) Vybere požadovanou kvalitu tisku. Pomocí jedné z následujících položek nastavte úroveň kvality tisku, která odpovídá zamýšlenému účelu. Chcete-li úroveň kvality tisku nastavit jednotlivě, klepněte na kartu Hlavní (Main) a pro položku Kvalita tisku (Print Quality) vyberte možnost Uživatelská (Custom). Položka Nastavit... (Set...) se stane aktivní. Klepnutím na tlačítko Nastavit... (Set...) otevřete Dialogové okno Uživatelská (Custom) (Custom) a zadejte požadovaná nastavení.
Výchozí (Defaults) Obnoví všechna změněná nastavení na výchozí hodnoty. Klepnutím na toto tlačítko vraťte u všech nastavení na kartách Rychlé nastavení (Quick Setup), Hlavní (Main) a Vzhled stránky (Page Setup) jejich výchozí hodnoty (nastavení výrobce).
Popis karty Hlavní Karta Hlavní (Main) umožňuje vytvořit základní nastavení tisku s ohledem na typ média. Pokud není požadován speciální tisk, lze pomocí nastavení položek na této kartě provést normální tisk. Náhled nastavení Obrázek papíru zobrazuje, jak bude originál umístěn na list papíru. Můžete zkontrolovat celkový obraz rozvržení. Typ média (Media Type) Vybere typ papíru pro tisk. Vyberte typ média odpovídající papíru vloženému do zařízení. Tím zaručíte náležitý tisk na konkrétní papír.
Koncept (Draft) Toto nastavení je vhodné pro zkušební tisk. Uživatelský (Custom) Tuto možnost vyberte, pokud chcete nastavit kvalitu tisku samostatně. Položka Nastavit... (Set...) je aktivní a je možné otevřít Dialogové okno Uživatelská (Custom) a zadat uživatelská nastavení. Nastavit... (Set...) Otevřete dialogové okno Uživatelská (Custom). Zde lze jednotlivě nastavit úroveň kvality tisku. Toto tlačítko aktivujte výběrem možnosti Uživatelská (Custom) položky Kvalita tisku (Print Quality).
kartu Karta Soulad dialogového okna Ruční nastavení barev (Manual Color Adjustment) a zadat požadovaná nastavení. Nastavit... (Set...) V dialogovém okně Ruční nastavení barev (Manual Color Adjustment) můžete upravit jednotlivá nastavení barev, například Azurová (Cyan), Purpurová (Magenta), Žlutá (Yellow), Jas (Brightness), Intenzita (Intensity) nebo Kontrast (Contrast) na kartě Nastavení barev (Color Adjustment) a vybrat metodu Oprava barev (Color Correction) na kartě Soulad (Matching).
Azurová (Cyan) / Purpurová (Magenta) / Žlutá (Yellow) Upraví sílu barev Azurová (Cyan), Purpurová (Magenta) a Žlutá (Yellow). Posunutím posuvníku doprava lze barvu zesílit a posunutím posuvníku doleva lze barvu zeslabit. Můžete rovněž ručně zadat hodnotu propojenou s posuvníkem. Zadejte hodnotu v rozmezí od -50 do 50. Tato úprava změní relativní množství inkoustu pro jednotlivé použité barvy, čímž dojde ke změně celkového vyvážení barev dokumentu.
Předvolby tisku vzorku... (Pattern Print preferences...) Otevře se dialogové okno Tisk vzorku (Pattern Print), které umožní nastavit položky úprav a nastavení tisku vzorku, například počet vzorků. Dialogové okno Tisk vzorku (Pattern Print) Provede nastavení pro tisk vzorků, které umožní zkontrolovat vyvážení barev a intenzitu a kontrast dokumentů. Nastavované parametry (Parameters to Adjust) Vyberte položku, která má být zkontrolována pomocí tisku vzorku.
Velký (Large) Azurová/Purpurová/Žlutá (Cyan/Magenta/Yellow) 19 Intenzita/Kontrast (Intensity/Contrast) 25 Malý (Small) Azurová/Purpurová/Žlutá (Cyan/Magenta/Yellow) 7 Intenzita/Kontrast (Intensity/Contrast) 9 Poznámka Možnosti Největší (Largest) a Velký (Large) nelze vybrat, jsou-li zvoleny určité velikosti papíru nebo výstupní velikosti papíru. V náhledu nastavení na kartě Hlavní (Main) je zobrazen obrázek, který umožňuje zkontrolovat celkové rozvržení.
Žádné (None) Deaktivuje úpravu barev pomocí ovladače tiskárny. Poznámka V ovladači tiskárny XPS se položka ICM změnila na Párování profilu ICC (ICC Profile Matching). Vstupní profil (Input Profile) Určuje vstupní profil, který chcete použít, když vyberete hodnotu ICM (Párování profilu ICC (ICC Profile Matching)) položky Oprava barev (Color Correction). Standardní (Standard) Je použit standardní profil tiskárny (sRGB), který podporuje barevný prostor ICM. Toto je výchozí nastavení.
Důležité V závislosti na nastavení Typ média (Media Type) lze stejného výsledku tisku dosáhnout, i když dojde ke změně nastavení Kvalita tisku (Print Quality). Náhled před tiskem (Preview before printing) Zobrazí vzhled výsledku tisku ještě před samotným vytištěním dat. Chcete-li zobrazit náhled před tiskem, zaškrtněte toto políčko. Pokud nechcete náhled zobrazit, zrušte zaškrtnutí tohoto políčka. Důležité Před využitím funkce Náhled tisku Canon IJ XPS je třeba v počítači nainstalovat profil Microsoft .
Popis karty Údržba Karta Údržba (Maintenance) umožňuje provádět údržbu zařízení nebo měnit nastavení zařízení. Čištění (Cleaning) Provede čištění tiskové hlavy. Čištění tiskové hlavy odstraní překážky z trysek tiskové hlavy. Čištění proveďte, pokud je tisk slabý nebo se některá barva netiskne, přestože jsou všechny hladiny inkoustu dostatečně vysoké. Hloubkové čištění (Deep Cleaning) Provede hloubkové čištění. Hloubkové čištění proveďte tehdy, nevyřeší-li potíže s tiskovou hlavou dva pokusy o čištění.
Vybere skupinu inkoustu, pro kterou chcete očistit tiskovou hlavu. Chcete-li zobrazit položky, které je třeba zkontrolovat před provedením čištění nebo hloubkového čištění, klepněte na tlačítko Výchozí položky testu (Initial Check Items). Výchozí položky testu (Initial Check Items) Zkontrolujte, zda je napájení zařízení zapnuto, a otevřete kryt zařízení. U každého inkoustu zkontrolujte následující položky. Potom, v případě potřeby, proveďte funkci Kontrola trysek (Nozzle Check) nebo Čištění (Cleaning).
Dialogové okno Nastavení tiskové hlavy (Print Head Alignment) Chcete-li nastavit polohu tiskové hlavy ručně, klepněte na položku Nastavit tiskovou hlavu (Align Print Head) v dialogovém okně Spustit nastavení tiskové hlavy (Start Print Head Alignment) a proveďte operace popsané v zobrazených zprávách. Potom se zobrazí dialogové okno Nastavení tiskové hlavy (Print Head Alignment). Toto dialogové okno umožňuje kontrolu vytištěného vzoru a nastavení polohy tiskové hlavy.
pravá bitová mapa (špatně) Trysky tiskové hlavy mohou být zanesené. Konec (Exit) Zavře dialogové okno Kontrola vzorku (Pattern Check) a vrátí se na kartu Údržba (Maintenance). Čištění (Cleaning) Provede čištění tiskové hlavy. Čištění tiskové hlavy odstraní překážky z trysek tiskové hlavy. Čištění proveďte, pokud je tisk slabý nebo se některá barva netiskne, přestože jsou všechny hladiny inkoustu dostatečně vysoké.
Pouze barevná (Color Only) Použije pouze barevnou kazetu FINE. Pouze černá (Black Only) Použije pouze černou kazetu FINE. Černá i barevná (Both Black and Color) Použije ty kazety FINE instalované v zařízení, které jsou barevné a černé. Důležité Pokud je v nabídce Typ média (Media Type) na kartě Hlavní (Main) vybráno jiné nastavení než Běžný papír (Plain Paper) nebo Obálka (Envelope), funkce Pouze černá (Black Only) nebude dostupná, protože zařízení bude k tisku dokumentů využívat barevné kazety FINE.
Automatické zapínání/vypínání (Auto Power) Otevře Dialogové okno Nastavení automatického zapínání/vypínání (Auto Power Settings). Zadejte nastavení pro automatické ovládání napájení zařízení. Tuto funkci proveďte, pokud chcete změnit nastavení automatického zapínání/vypínání. Poznámka Pokud je zařízení vypnuto nebo je zakázána komunikace mezi zařízením a počítačem, může se objevit chybová zpráva, protože počítač nemůže zjišťovat údaje o stavu zařízení.
Dialogové okno Tiché nastavení (Quiet Settings) Po klepnutí na položku Tiché nastavení (Quiet Settings) se zobrazí dialogové okno Tiché nastavení (Quiet Settings). Dialogové okno Tiché nastavení (Quiet Settings) umožňuje zadat nastavení, které sníží provozní hluk zařízení. Tichý režim je vhodný k dalšímu ztišení provozního hluku zařízení (například v noci). Tato funkce může snížit rychlost tisku.
Pokud taková situace nastane, klepnutím na tlačítko OK zobrazíte nejaktuálnější nastavení zadaná v počítači. Dialogové okno Uživatelská nastavení (Custom Settings) Po klepnutí na položku Uživatelská nastavení (Custom Settings) se zobrazí dialogové okno Uživatelská nastavení (Custom Settings). Podle potřeby přepínejte mezi různými provozními režimy zařízení.
Zobrazit stav tiskárny (View Printer Status) Spustí aplikaci Monitor stavu Canon IJ. Tuto funkci proveďte, pokud chcete zkontrolovat stav tiskárny a postup probíhající tiskové úlohy. Poznámka Používáte-li ovladač tiskárny XPS, se odkaz „Monitor stavu Canon IJ“ změní na odkaz „Monitor stavu Canon IJ XPS“. Etiketa (About) Otevře Dialogové okno Etiketa (About) (About). Zde můžete zkontrolovat verzi ovladače tiskárny a informace o ochraně autorských práv. Je zde také možné změnit použitý jazyk.
Související funkce Snížení hlučnosti zařízení Změna provozního režimu zařízení 148
Popis aplikace Náhled na tiskárnu Canon IJ Náhled na tiskárnu Canon IJ je aplikace, která ještě před tiskem zobrazí, jak bude vypadat výsledný tisk. Náhled vychází z informací, které jsou nastaveny v ovladači tiskárny a umožňuje zkontrolovat rozvržení dokumentu, pořadí tisku a počet stránek. Můžete také změnit typ média. Pokud chcete před tiskem zobrazit náhled, otevřete okno nastavení ovladače tiskárny, a zaškrtněte políčko Náhled před tiskem (Preview before printing) na kartě Hlavní (Main).
Konec (Exit) Ukončí aplikaci Náhled na tiskárnu Canon IJ. Nabídka Stránka (Page) Tato nabídka obsahuje následující příkazy pro výběr stránky, která má být zobrazena. Všechny tyto příkazy s výjimkou příkazu Vybrat stránku lze také vybrat v panelu nástrojů. První stránka (First Page) Zobrazí první stránku dokumentu. Pokud je aktuálně zobrazená stránka na prvním místě, je tento příkaz zobrazen šedě a nelze jej vybrat.
Celé (Whole) Zobrazí celou stránku dat na jedné stránce. 50% Zmenší zobrazená data na 50 % skutečné velikosti, ve které mají být vytištěna. 100% Zobrazí data ve skutečné velikosti, ve které mají být vytištěna. 200% Zvětší zobrazená data na 200 % skutečné velikosti, která má být vytištěna. 400% Zvětší zobrazená data na 400 % skutečné velikosti, která má být vytištěna.
Zdroj papíru (Paper Source) Zobrazí zdroj papíru dokumentu, který chcete vytisknout. Rozvržení stránky (Page Layout) Zobrazí rozvržení stránky dokumentu, který chcete vytisknout. Důležité Pokud jsou typ média a zdroj papíru nastaveny v aplikaci, tato nastavení mají přednost a změněná nastavení mohou být neúčinná.
Popis aplikace Náhled na tiskárnu Canon IJ XPS Náhled na tiskárnu Canon IJ XPS je aplikace, která ještě před tiskem zobrazí, jak bude vypadat výsledný tisk. Náhled vychází z informací, které jsou nastaveny v ovladači tiskárny a umožňuje zkontrolovat rozvržení dokumentu, pořadí tisku a počet stránek. Náhled také umožňuje úpravy tištěného dokumentu, úpravy tištěných stránek, změnu nastavení tisku a další funkce.
Tisknout všechny dokumenty (Print All Documents) Vytiskne všechny dokumenty v seznamu dokumentů a zavře aplikaci Náhled na tiskárnu Canon IJ XPS. Uložit historii tisku (Save Print History) Přepíná, zda mají být dokumenty tištěné pomocí aplikace Náhled na tiskárnu Canon IJ XPS uloženy jako položky historie tisku. Omezení počtu položek historie (History Entry Limit) Přepne maximální počet záznamů v historii tisku. Vyberte možnost 10 položek (10 Entries), 30 položek (30 Entries) nebo 100 položek (100 Entries).
Obnovit dokumenty (Reset Documents) Vrátí dokument vybraný v seznamu dokumentů do stavu před jeho přidáním do aplikace Náhled na tiskárnu Canon IJ XPS. Sloučené dokumenty jsou rozděleny a původní dokumenty jsou obnoveny. Tento příkaz má stejnou funkci jako položka nástrojů. (Obnovit dokumenty) na panelu Přesunout dokument (Move Document) Pomocí následujícího příkazu změňte pořadí dokumentů vybraných v seznamu dokumentů.
Tisk rozvržené stránky... (Page Layout Printing...) Otevře dialogové okno Tisk rozvržené stránky (Page Layout Printing). Toto dialogové okno umožňuje nastavit možnosti Tisk rozvržené stránky (Page Layout Printing), Stránky (Pages), Pořadí stránek (Page Order) a Ohraničení stránky (Page Border). Oboustranný tisk... (Duplex Printing...) Otevře dialogové okno Oboustranný tisk (Duplex Printing).
Přesunout o stránku vpřed (Move Forward One) Přesune aktuálně vybranou stránku z její aktuální polohy o jedno místo vpřed. Pokud je aktuálně vybraná stránka na prvním místě, je tento příkaz zobrazen šedě a nelze jej vybrat. Přesunout o stránku vzad (Move Backward One) Přesune aktuálně vybranou stránku z její aktuální polohy o jedno místo vzad. Pokud je aktuálně vybraná stránka na posledním místě, je tento příkaz zobrazen šedě a nelze jej vybrat.
První stránka (First Page) Zobrazí první stránku dokumentu. Pokud je aktuálně zobrazená stránka na prvním místě, je tento příkaz zobrazen šedě a nelze jej vybrat. Předchozí stránka (Previous Page) Zobrazí stránku umístěnou před aktuálně zobrazenou stránkou. Pokud je aktuálně zobrazená stránka na prvním místě, je tento příkaz zobrazen šedě a nelze jej vybrat. Další stránka (Next Page) Zobrazí stránku umístěnou za aktuálně zobrazenou stránkou.
200% Zvětší zobrazená data na 200 % skutečné velikosti, která má být vytištěna. 400% Zvětší zobrazená data na 400 % skutečné velikosti, která má být vytištěna. Nabídka Možnosti (Option) Přepíná stav zobrazit/skrýt následujících informací. Zobrazit miniatury (View Thumbnails) Potlačí všechny stránky v dokumentu vybrané v seznamu dokumentů a zobrazí je v dolní části okna náhledu. Tento příkaz má stejnou funkci jako položka (Zobrazit miniatury) na panelu nástrojů.
(Sloučit dokumenty) Sloučí dokumenty vybrané v seznamu dokumentů do jednoho dokumentu. Pokud je vybrán jen jeden dokument, je tento příkaz zobrazen šedě a nelze jej vybrat. (Odstranit dokument) Odstraní vybraný dokument ze seznamu dokumentů. Pokud seznam dokumentů obsahuje pouze jeden dokument, je tento dokument zobrazen šedě a nelze jej vybrat. (Obnovit dokumenty) Vrátí dokument vybraný v seznamu dokumentů do stavu před jeho přidáním do aplikace Náhled na tiskárnu Canon IJ XPS.
(Zpět) Vrátí zpět předchozí změnu. Pokud nelze vzít změnu zpět, je tato funkce zobrazena šedě a nelze ji vybrat. (Odstranit stránku) Odstraní aktuálně vybranou stránku. Pokud je nastaven tisk rozvržené stránky, budou stránky ohraničené červeným rámečkem odstraněny. Seznam dokumentů Zobrazí seznam tištěných dokumentů. Dokument vybraný v seznamu dokumentů se stane objektem pro zobrazení náhledu a úpravy. Název dokumentu (Document Name) Zobrazí název tištěného dokumentu.
Karta Informace o stránce (Page Information) Nastavení tisku jsou zobrazena pro každou stránku. Můžete změnit typ média a nastavení zdroje papíru. Velikost papíru v tiskárně (Printer Paper Size) Zobrazí velikost papíru dokumentu, který chcete vytisknout. Typ média (Media Type) Umožňuje vybrat typ média dokumentu, který chcete vytisknout. Zdroj papíru (Paper Source) Umožňuje vybrat zdroj papíru dokumentu, který chcete vytisknout.
snížíte. Můžete rovněž ručně zadat hodnotu propojenou s posuvníkem. Zadejte hodnotu v rozmezí od -50 do 50. Kontrast (Contrast) V obrázku, který chcete vytisknout, upraví kontrast mezi světlou a tmavou. Posunutím posuvníku doprava se kontrast zvýší, posunutím doleva se kontrast sníží. Můžete rovněž ručně zadat hodnotu propojenou s posuvníkem. Zadejte hodnotu v rozmezí od -50 do 50. Výchozí (Defaults) Obnoví všechna změněná nastavení na výchozí hodnoty.
Konec (Exit) Ukončí aplikaci Náhled na tiskárnu Canon IJ XPS. Dokumenty zbývající v seznamu dokumentů budou z tohoto seznamu odstraněny. Tisk (Print) Vytiskne dokumenty vybrané v seznamu dokumentů. Vytištěné dokumenty jsou odstraněny ze seznamu; po vytištění všech dokumentů se Náhled na tiskárnu Canon IJ zavře.
Popis dialogového okna Monitor stavu Canon IJ Otevře se monitor stavu Canon IJ, který zobrazí stav zařízení a průběh tisku. Monitor oznamuje stav zařízení pomocí grafiky, ikon a zpráv. Funkce monitoru stavu Canon IJ Monitor stavu Canon IJ nabízí následující výhody: Stav tiskárny lze zjistit na obrazovce. Stav zařízení je na obrazovce zobrazen v reálném čase. Můžete sledovat průběh tisku jednotlivých tištěných dokumentů (tiskových úloh). Na obrazovce jsou zobrazeny typy chyb a jejich řešení.
Kazeta FINE Pokud dojde k varování při nízké hladině inkoustu nebo k chybě z důvodu chybějícího inkoustu, zobrazí monitor stavu Canon IJ ikonu. Tato funkce dále zobrazí grafiku informující o odhadovaných hladinách inkoustu kazety FINE. V takovém případě otevřete dialogové okno Podrobnosti o inkoustu (Ink Details). Můžete zjistit podrobné informace, například zbývající hladinu inkoustu a typy kazety FINE tiskárny. Název dokum. (Document Name) Zobrazí název dokumentu, který chcete vytisknout.
Zobrazit varování automaticky (Display Warning Automatically) Zobrazení varování při nízké hladině inkoustu (When a Low Ink Warning Occurs) Automaticky se spustí okno monitoru stavu Canon IJ, které se zobrazí před ostatními okny, v případě varování při nízké hladině inkoustu. Spustit po startu Windows (Start when Windows is Started) Automaticky spustí monitor stavu Canon IJ při startu systému Windows.
Aktualizace ovladačů MP Drivers Získání nejnovějších ovladačů MP Drivers Odstranění nepotřebných ovladačů MP Drivers Příprava před instalací ovladačů MP Drivers Instalace ovladačů MP Drivers 168
Získání nejnovějších ovladačů MP Drivers Ovladače MP Drivers zahrnují ovladač tiskárny a ovladače ScanGear (ovladač skeneru). Aktualizací ovladačů MP Drivers na nejnovější verzi ovladačů MP Driversmůžete vyřešit nevyřešené problémy. Podle potřeby můžete navštívit naši webovou stránku a stáhnout nejnovější ovladače MP Drivers pro váš model. Důležité Ovladače MP Drivers si můžete stáhnout bezplatně, ale budete muset uhradit případné poplatky za internetové připojení.
Odstranění nepotřebných ovladačů MP Drivers Ovladače MP Drivers, které již nepoužíváte, můžete odstranit. Při odstraňování ovladačů MP Drivers nejprve ukončete všechny spuštěné programy. Při odstraňování nepotřebných ovladačů MP Drivers postupujte takto: 1. Spusťte odinstalační program • Používáte-li systém Windows 8, mezi ovládacími tlačítky na pracovní ploše vyberte Nastavení (Settings) -> Ovládací panely (Control Panel) -> Programy (Programs) -> Programy a funkce (Programs and Features).
Klepněte na tlačítko Provést (Execute). Po zobrazení okna se žádostí o potvrzení klepněte na tlačítko Ano (Yes). Po odstranění všech souborů klepněte na tlačítko Hotovo (Complete). Tímto je dokončeno odstranění ovladačů MP Drivers. Důležité Pokud odinstalujete ovladače MP Drivers, bude odstraněn ovladač tiskárny, ovladač tiskárny XPS a ovladače ScanGear (ovladač skeneru).
Příprava před instalací ovladačů MP Drivers Tato část popisuje položky, které je třeba zkontrolovat před instalací ovladačů MP Drivers. Tuto část si také můžete přečíst v případě, že ovladače MP Drivers nelze nainstalovat. Kontrola stavu zařízení • Zkontrolujte, zda jsou porty USB tohoto zařízení a počítače spolehlivě propojeny kabelem USB. • Vypněte zařízení. Kontrolování nastavení počítače • Ukončete všechny spuštěné aplikace.
Instalace ovladačů MP Drivers Prostřednictvím Internetu se můžete připojit na naše webové stránky a stáhnout nejnovější ovladače MP Drivers a ovladač tiskárny XPS pro svůj model. Při instalaci stažených ovladačů MP Drivers postupujte takto: 1. Vypněte zařízení 2. Spusťte instalační program Poklepejte na ikonu staženého souboru. Spustí se instalační program.
V závislosti na prostředí používaného systému se může zobrazit hlášení s výzvou k restartování počítače. K řádnému dokončení instalace je třeba restartovat počítač. Důležité Ovladač tiskárny XPS můžete nainstalovat stejným způsobem jako ovladače tiskárny MP Drivers. Pokud instalujete ovladač tiskárny XPS, dokončete nejdříve instalaci ovladačů tiskárny MP Drivers.
Sdílení tiskárny v síti Pokud používáte v síti více počítačů, můžete sdílet tiskárnu, která je připojena k jednomu počítači, s ostatními počítači. Počítače se systémy Windows připojené k síti nemusí být nezbytně stejné. • Nastavení tiskového serveru Tato část popisuje postup nastavení počítače, který je přímo připojen k tiskárně pomocí kabelu USB. • Nastavení klientského počítače Tato část popisuje postup nastavení počítače, který používá tuto tiskárnu prostřednictvím sítě.
Nastavení tiskového serveru Chcete-li používat tiskárnu v síti, nastavte v ovladači tiskárny sdílení v systému tiskového serveru. Chcete-li nastavit systémy tiskového serveru, postupujte takto: 1. Nainstalujte ovladače MP drivers do systému tiskového serveru 2.
• Používáte-li systém Windows Vista, stiskněte na klávesnici klávesu Alt a pak v zobrazené nabídce Soubor (File) vyberte možnosti Spustit jako správce (Run as administrator) -> Sdílení... (Sharing...). • Používáte-li systém Windows XP, vyberte z nabídky Soubor (File) příkaz Sdílení... (Sharing...). Důležité V systému Windows 8, Windows 7 nebo Windows Vista se při spuštění, instalování nebo odinstalování softwaru může zobrazit potvrzovací dialogové okno nebo okno s upozorněním.
Nastavení klientského počítače Po nastavení systému tiskového serveru nastavte systémy klientů. Chcete-li nastavit systémy klientů, postupujte takto: Pokud používáte systém Windows 8, Windows 7 nebo Windows Vista 1. Nainstalujte ovladače MP drivers do systémů klientů Poznámka Na klientském počítači je třeba ručně zvolit cíl připojení. Během instalace klepněte na tlačítko Storno (Cancel) v okně Připojit kabel (Connect Cable). Po zobrazení okna se žádostí o potvrzení klepněte na tlačítko Ano (Yes).
Poznámka Pokud se ikona tiskárny nezobrazí, ověřte, zda je tiskárna skutečně připojena k tiskovému serveru. Zobrazení ikony tiskárny může nějakou dobu trvat. 4. Dokončete nastavení Proveďte akci popsanou na obrazovce a pak klepněte na tlačítko Dokončit (Finish). • Používáte-li systém Windows 8 nebo Windows 7, bude ikona sdílené tiskárny vytvořena v okně Zařízení a tiskárny (Devices and Printers). • Používáte-li systém Windows Vista, bude ikona sdílené tiskárny vytvořena v okně Tiskárny (Printers).
Vyberte možnost Síťová tiskárna nebo tiskárna připojená k jinému počítači (A network printer, or a printer attached to another computer) a pak klepněte na tlačítko Další (Next). V okně Určit tiskárnu (Specify a Printer) klepněte na tlačítko Další (Next) a vyhledejte systém tiskového serveru. Klepněte na ikonu tiskárny, kterou jste v systému tiskového serveru nakonfigurovali jako sdílenou, a poté klepněte na tlačítko Další (Next).
Omezení týkající se sdílení tiskárny Používáte-li ovladač tiskárny XPS, při čtení těchto informací nahrazujte odkaz „Náhled na tiskárnu Canon IJ“ odkazem „Náhled na tiskárnu Canon IJ XPS“. Zde jsou uvedena omezení, která platí v případě, že používáte tiskárnu v prostředí sítě. Zjistěte, jaká omezení platí v prostředí, které používáte. Pokud sdílíte tiskárnu v síti • Může se zobrazit zpráva upozorňující na dokončení tisku.
Na kartě Upřesnit (Advanced) zrušte zaškrtnutí políčka Oznámit tisk vzdálených dokumentů (Notify when remote documents are printed) a restartujte počítač. • Funkce obousměrné komunikace je zablokována a může se stát, že nebude rozpoznán správný stav tiskárny.
Kopírování Vytváření kopií Základní Přepínání velikosti stránky mezi formáty A4 a Letter 183
Vytváření kopií Originál, který chcete kopírovat, položte na skleněnou desku. 1. Zkontrolujte, zda je zařízení zapnuté. 2. Vložte běžný papír formátu A4 nebo Letter. 3. Položte originál na skleněnou desku. Poznámka • Velikost papíru vloženého do zadní přihrádky můžete přepínat mezi formáty A4 a Letter. Přepínání velikosti stránky mezi formáty A4 a Letter 4. Chcete-li kopírovat barevně, stiskněte tlačítko Barevný (Color). Chcete-li kopírovat černobíle, stiskněte tlačítko Černý (Black).
Poznámka • Chcete-li kopírování zrušit, stiskněte tlačítko Zastavit (Stop). • Nastavení kvality tisku na hodnotu „Koncept“ (prioritou rychlost) Kvalitu tisku můžete nastavit na hodnotu „Koncept“ (prioritou rychlost) následujícím způsobem. 1. V kroku 4 stiskněte a alespoň 2 sekundy podržte tlačítko Barevný (Color) nebo Černý (Black). Kontrolka ZAPNOUT (ON) jednou blikne. 2. Uvolněte tlačítko. Zařízení začne kopírovat.
Přepínání velikosti stránky mezi formáty A4 a Letter Velikost papíru vloženého do zadní přihrádky můžete přepínat mezi formáty A4 a Letter. Toto nastavení je vhodné, pokud do zadní přihrádky obvykle vkládáte papír formátu Letter. 1. Zkontrolujte, zda je zařízení zapnuté. 2. Stiskněte tlačítko Zastavit (Stop) a podržte je, dokud kontrolka Alarm 10krát nezabliká. 3. Uvolněte tlačítko Zastavit (Stop). Kontrolka ZAPNOUT (ON) přestane svítit a začne blikat. 4.