MG6400 series Online-Handbuch Scannen Deutsch (German)
Inhalt Scannen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Scannen über den Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Scannen mit IJ Scan Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Was ist IJ Scan Utility (Scanner-Software)?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registerkarte Basismodus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Registerkarte Erweiterter Modus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Eingabe-Einstellungen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Ausgabe-Einstellungen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scannen Scannen über den Computer Scannen mit IJ Scan Utility Scannen mit verwendeter Anwendungssoftware (ScanGear) Hilfreiche Informationen über das Scannen Menü und Einstellungsfenster von IJ Network Scanner Selector EX Weitere Scan-Methoden Objekte platzieren (beim Scannen über den Computer) Scannen über das Bedienfeld des Geräts Weiterleiten gescannter Daten auf den Computer mithilfe des Bedienfelds am Gerät Grundlagen Anhängen der gescannten Daten an eine E-Mail über das Bedienfeld am Gerät Speichern v
Scannen über den Computer Scannen mit IJ Scan Utility Scannen mit verwendeter Anwendungssoftware (ScanGear) Hilfreiche Informationen über das Scannen Menü und Einstellungsfenster von IJ Network Scanner Selector EX Weitere Scan-Methoden Objekte platzieren (beim Scannen über den Computer) 5
Scannen mit IJ Scan Utility Was ist IJ Scan Utility (Scanner-Software)? Starten von IJ Scan Utility Einfaches Scannen mit dem automatischen Scan Grundlagen Fotos scannen Dokumente scannen Scannen mit bevorzugten Einstellungen Objekte scannen, die größer als die Auflagefläche sind (Bild zusammenfügen) Mehrere Objekte gleichzeitig scannen Speichern nach dem Prüfen der Scanergebnisse Gescannte Bilder per E-Mail versenden Extrahieren von Text aus gescannten Bildern (OCR) Bildschirme von IJ Scan Utility 6
Was ist IJ Scan Utility (Scanner-Software)? IJ Scan Utility ist eine Anwendung, mit der Sie auf einfache Weise Fotos, Dokumente usw. scannen können. Sie können mehrere Schritte, vom Scannen bis zum Speichern, gleichzeitig durchführen, indem Sie auf das entsprechende Symbol im Hauptbildschirm von IJ Scan Utility klicken. Funktionen von IJ Scan Utility Einfach gemäß Verwendungszweck scannen Sie können einfach durch Klicken auf Symbole scannen.
Integration in Anwendungen Sie können gescannte Bilder über die Integration in andere Anwendungen verwenden und gescannte Bilder in Ihrer bevorzugten Anwendung anzeigen, sie an E-Mails anhängen, Text aus Bildern extrahieren usw. Wichtig Einige Funktionen sind nur verfügbar, wenn My Image Garden installiert ist. Hinweis Informationen zum Festlegen der zu integrierenden Anwendungen finden Sie unter "Dialogfeld Einstellungen".
Starten von IJ Scan Utility Hinweis Wenn Sie mehrere Scanner verwenden oder den Verbindungstyp von einer USB- zu einer Netzwerkverbindung geändert haben, richten Sie die Netzwerkverbindung über IJ Scan Utility ein. Netzwerk-Scan-Einstellungen Befolgen Sie die unten genannten Schritte, um IJ Scan Utility zu starten. Windows 8: Wählen Sie IJ Scan Utility im Start-Bildschirm aus, um IJ Scan Utility zu starten.
Einfaches Scannen mit dem automatischen Scan Vereinfachen Sie das Scannen durch die automatische Erkennung des Objekttyps. Wichtig Die folgenden Objekttypen können möglicherweise nicht korrekt gescannt werden. Passen Sie in diesem Fall die Schnittrahmen (Scanbereiche) in der Gesamtbildansicht von ScanGear (Scanner-Treiber) an und scannen Sie erneut. Fotos mit weißlichem Hintergrund Auf weißem Papier gedruckte Objekte, handgeschriebene Dokumente, Visitenkarten usw. Dünne Objekte Dicke Objekte 1.
Im Dialogfeld Einstellungen (Automatisch scannen) (Settings (Auto Scan)) können Sie ebenfalls erweiterte Einstellungen für das Scannen festlegen. Auf den folgenden Seiten finden Sie Informationen zum Scannen mit Angabe des Objekttyps.
Fotos scannen Sie können auf der Auflagefläche liegende Fotos mit den für Fotos geeigneten Einstellungen scannen. 1. Legen Sie das Foto auf die Auflagefläche. Objekte platzieren (beim Scannen über den Computer) 2. Starten Sie IJ Scan Utility. 3. Klicken Sie auf Einst... (Settings...), wählen Sie das Dialogfeld Einstellungen (Foto scannen) (Settings (Photo Scan)) aus und geben Sie das Papierformat, die Auflösung etc. an. Wenn Sie die Einstellungen vorgenommen haben, klicken Sie auf OK. 4.
Dokumente scannen Sie können auf der Auflagefläche liegende Objekte mit den für Dokumenten geeigneten Einstellungen scannen. 1. Legen Sie das Objekt auf die Auflagefläche. Objekte platzieren (beim Scannen über den Computer) 2. Starten Sie IJ Scan Utility. 3. Klicken Sie auf Einst... (Settings...), wählen Sie das Dialogfeld Einstellungen (Dokument scannen) (Settings (Document Scan)) aus und geben Sie das Papierformat, die Auflösung etc. an. Wenn Sie die Einstellungen vorgenommen haben, klicken Sie auf OK.
Scannen mit bevorzugten Einstellungen Sie können auf der Auflagefläche liegende Objekte mit Ihren bevorzugten und vorab gespeicherten Einstellungen scannen. Dies ist praktisch für das Speichern von häufig verwendeten Einstellungen und das Festlegen von detaillierten Scaneinstellungen. 1. Starten Sie IJ Scan Utility. 2. Klicken Sie auf Einst... (Settings...), wählen Sie das Dialogfeld Einstellungen (Benutzerdefiniert scannen) (Settings (Custom Scan)) und geben Sie die Quelle, die Auflösung etc. an.
Objekte scannen, die größer als die Auflagefläche sind (Bild zusammenfügen) Sie können die rechten und linken Hälften eines Objekts, das größer als die Auflagefläche ist, scannen und die gescannten Bilder anschließend wieder zu einem Bild zusammenfügen. Es werden Objekte unterstützt, die etwa doppelt so groß wie die Auflagefläche sind. Hinweis Nachfolgend wird beschrieben, wie mit dem Scannen des Objekts begonnen wird, das auf der linken Bildschirmseite angezeigt werden soll. 1.
5. Stellen Sie sicher, dass Von links scannen (Scan from Left) unter Scanrichtung (Scan Direction) ausgewählt ist. 6. Legen Sie das Objekt, das auf der linken Bildschirmseite angezeigt werden soll, mit dem Schriftbild nach unten auf die Auflagefläche. 7. Klicken Sie auf Scannen von Bild 1 beginnen (Start Scanning Image 1).
Das erste Objekt wird gescannt und in 1 angezeigt. Hinweis Klicken Sie auf Abbrechen (Cancel), um den Scanvorgang abzubrechen. 8. Legen Sie das Objekt, das auf der rechten Bildschirmseite angezeigt werden soll, mit dem Schriftbild nach unten auf die Auflagefläche. 9. Klicken Sie auf Scannen von Bild 2 beginnen (Start Scanning Image 2).
Das zweite Objekt wird gescannt und in 2 angezeigt. Hinweis Klicken Sie auf Abbrechen (Cancel), um den Scanvorgang abzubrechen. 10. Passen Sie die gescannten Bilder nach Ihren Vorstellungen an. Verwenden Sie die Symbolleiste zum Drehen und Vergrößern/Verkleinern, oder ziehen Sie die Bilder, um ihre Position zu ändern.
Hinweis Aktivieren Sie das Kontrollkästchen Schnittrahmen anpassen (Adjust cropping frames), um den zu speichernden Bereich festzulegen. Anpassen von Schnittrahmen im Fenster Bild zusammenfügen Zum erneuten Scannen eines Objekts wählen Sie das Bild im Vorschaubereich oder die Miniaturansicht oben im Bildschirm aus und klicken dann auf (Löschen). Das ausgewählte Bild wird gelöscht, und Sie können das Objekt erneut scannen. 11. Klicken Sie auf Speichern (Save). Das zusammengesetzte Bild wird gespeichert.
Mehrere Objekte gleichzeitig scannen Sie können zwei oder mehr Fotos (kleine Objekte) auf der Auflagefläche gleichzeitig scannen und jedes Bild einzeln speichern. Wichtig Die folgenden Objekttypen können möglicherweise nicht korrekt gescannt werden. Passen Sie in diesem Fall die Schnittrahmen (Scanbereiche) in der Gesamtbildansicht von ScanGear (Scanner-Treiber) an und scannen Sie erneut. Fotos mit weißlichem Hintergrund Auf weißem Papier gedruckte Objekte, handgeschriebene Dokumente, Visitenkarten usw.
Das Dialogfeld Einstellungen wird angezeigt. 4. Klicken Sie auf Benutzerdefiniert scannen (Custom Scan). 5. Wählen Sie unter Quelle wählen (Select Source) den Typ der zu scannenden Objekte aus.
6. Wählen Sie Automatisch scannen (Auto scan) unter Papierformat (Paper Size) aus, und klicken Sie dann auf OK. Der Hauptbildschirm von IJ Scan Utility wird angezeigt. Hinweis Auf den folgenden Seiten finden Sie Einzelheiten zu den Einstellungselementen im Dialogfeld Einstellungen.
Dialogfeld Einstellungen (Benutzerdefiniert scannen) 7. Klicken Sie auf Benutzerdef. (Custom). Es werden mehrere Objekte gleichzeitig gescannt. Hinweis Klicken Sie auf Abbrechen (Cancel), um den Scanvorgang abzubrechen. Gescannte Bilder werden in dem Ordner gespeichert, der unter Speichern in (Save in) im entsprechenden Dialogfeld Einstellungen festgelegt ist. Das Dialogfeld wird durch Klicken auf Einst... (Settings...) angezeigt.
Speichern nach dem Prüfen der Scanergebnisse Sie können die Scanergebnisse prüfen und die Bilder dann auf einem Computer speichern. Wichtig Sie können die Scanergebnisse nicht vor dem Speichern prüfen, wenn Sie mit der Einstellung Automatisch (Auto) oder über das Bedienfeld scannen. Hinweis Die Bildschirme für das Scannen von Fotos werden in den folgenden Beschreibungen als Beispiele verwendet. 1. Starten Sie IJ Scan Utility. 2. Klicken Sie auf Einst... (Settings...).
4. Aktivieren Sie das Kontrollkästchen Scanergebnisse prüfen (Check scan results), und klicken Sie anschließend auf OK. Der Hauptbildschirm von IJ Scan Utility wird angezeigt. Hinweis Auf den folgenden Seiten finden Sie Einzelheiten zu den Einstellungselementen im Dialogfeld Einstellungen.
Hinweis Klicken Sie auf Abbrechen (Cancel), um den Scanvorgang abzubrechen. 6. Ändern Sie nach Bedarf die Bildfolge oder die Dateispeicheroptionen. Sie können die Bildfolge bzw. die Dateispeicheroptionen im Dialogfeld Speichereinstellungen (Save Settings) festlegen. Hinweis Die folgenden Ordner werden standardmäßig zum Speichern angegeben.
Gescannte Bilder per E-Mail versenden Sie können gescannte Bilder per E-Mail versenden. Hinweis Die Bildschirme für das Scannen von Fotos werden in den folgenden Beschreibungen als Beispiele verwendet. 1. Starten Sie IJ Scan Utility. 2. Klicken Sie auf Einst... (Settings...). Das Dialogfeld Einstellungen wird angezeigt. 3. Klicken Sie auf Foto scannen (Photo Scan).
4. Wählen Sie unter Anwendungseinstellungen (Application Settings) die Option An E-Mail anhängen (Attach to e-mail) und dann ein E-MailProgramm aus. Hinweis Sie können für Anhänge zu verwendende E-Mail-Programme aus dem PullDown-Menü hinzufügen. Wenn Keines (manuell anhängen) (None (Attach Manually)) ausgewählt ist, hängen Sie die gescannten und gespeicherten Bilder manuell an eine E-Mail an. 5. Klicken Sie auf OK.
Der Hauptbildschirm von IJ Scan Utility wird angezeigt. Hinweis Auf den folgenden Seiten finden Sie Einzelheiten zu den Einstellungselementen im Dialogfeld Einstellungen. Dialogfeld Einstellungen (Automatisch scannen) Dialogfeld Einstellungen (Foto scannen) Dialogfeld Einstellungen (Dokument scannen) Dialogfeld Einstellungen (Benutzerdefiniert scannen) Dialogfeld Einstellungen (ScanGear) 6. Klicken Sie auf Foto (Photo). Der Scan-Vorgang wird gestartet.
Die gescannten Bilder werden entsprechend den im Dialogfeld Einstellungen vorgenommenen Einstellungen gespeichert. Wenn das Kontrollkästchen Scanergebnisse prüfen (Check scan results) im Dialogfeld Einstellungen aktiviert ist, wird das Dialogfeld Speichereinstellungen (Save Settings) angezeigt. Nachdem Sie die Speicheroptionen festgelegt und auf OK geklickt haben, werden die gescannten Bilder gespeichert und im festgelegten E-Mail-Programm automatisch an eine neue Nachricht angehängt. 7.
Extrahieren von Text aus gescannten Bildern (OCR) Scannen Sie Text in gescannten Zeitschriften und Zeitungen und zeigen Sie ihn im Windows-Editor an. Hinweis Sie können Text beim Scannen über Dokument (Document), Benutzerdef. (Custom) oder ScanGear extrahieren. Die Bildschirme für das Scannen von Dokumenten werden in den folgenden Beschreibungen als Beispiele verwendet. 1. Starten Sie IJ Scan Utility. 2. Klicken Sie auf Einst... (Settings...). Das Dialogfeld Einstellungen wird angezeigt. 3.
Hinweis Für Auflösung (Resolution) kann nur 300 dpi oder 400 dpi eingestellt werden, wenn OCR starten (Start OCR) unter Anwendungseinstellungen (Application Settings) ausgewählt wurde. 4. Wählen Sie unter Anwendungseinstellungen (Application Settings) die Option OCR starten (Start OCR) aus, und wählen Sie dann die Anwendung zum Anzeigen des Ergebnisses aus. Hinweis Wird My Image Garden angegeben, wird nach dem Scannen des Bilds der Text im Bild extrahiert und im Editor von Windows angezeigt. 5.
Der Hauptbildschirm von IJ Scan Utility wird angezeigt. Hinweis Auf den folgenden Seiten finden Sie Einzelheiten zu den Einstellungselementen im Dialogfeld Einstellungen. Dialogfeld Einstellungen (Dokument scannen) Dialogfeld Einstellungen (Benutzerdefiniert scannen) Dialogfeld Einstellungen (ScanGear) 6. Klicken Sie auf Dokument (Document). Der Scan-Vorgang wird gestartet.
Der Text, der im Windows-Editor angezeigt wird, dient nur der Orientierung.
Bildschirme von IJ Scan Utility Hauptbildschirm von IJ Scan Utility Dialogfeld Einstellungen Dialogfeld Einstellungen (Automatisch scannen) Dialogfeld Einstellungen (Foto scannen) Dialogfeld Einstellungen (Dokument scannen) Dialogfeld Einstellungen (Benutzerdefiniert scannen) Dialogfeld Einstellungen (Scannen und zusammenfügen) Dialogfeld Einstellungen (ScanGear) Dialogfeld Einstellungen (Auf PC speichern (automatisch)) Dialogfeld Einstellungen (Auf PC speichern (Foto)) Dialogfeld Einstellungen (Auf PC spei
Hauptbildschirm von IJ Scan Utility Befolgen Sie die unten genannten Schritte, um IJ Scan Utility zu starten. Windows 8: Wählen Sie IJ Scan Utility im Start-Bildschirm aus, um IJ Scan Utility zu starten. Wenn IJ Scan Utility nicht im Start-Bildschirm angezeigt wird, wählen Sie den Charm Suchen (Search) aus und suchen Sie nach "IJ Scan Utility".
• Dokument (Document) Scannt Objekte als Dokumente und speichert diese auf einem Computer. Im Dialogfeld Einstellungen (Dokument scannen) (Settings (Document Scan)) können die Einstellungen für das Scannen/Speichern und das Verhalten nach dem Scannen angegeben werden. • Benutzerdef. (Custom) Scannt Objekte mit Ihren bevorzugten Einstellungen und speichert die Bilder auf einem Computer. Der Objekttyp kann automatisch erkannt werden.
Dialogfeld Einstellungen Das Dialogfenster für Einstellungen hat drei Registerkarten: (Scannen über den Computer), (Scannen über das Bedienfeld) und (Allgemeine Einstellungen). Wenn Sie auf eine Registerkarte klicken, ändert sich die Ansicht im roten Rahmen, und Sie können erweiterte Einstellungen für Funktionen auf den Registerkarten vornehmen. Registerkarte (Scannen über den Computer) Sie können das Verhalten für das Scannen über IJ Scan Utility oder My Image Garden festlegen.
Dialogfeld Einstellungen (An E-Mail anhängen (Foto)) Dialogfeld Einstellungen (An E-Mail anhängen (Dokument)) Wichtig Wenn das Dialogfenster für Einstellungen über My Image Garden geöffnet wird, wird die Registerkarte (Scannen über das Bedienfeld) nicht angezeigt. Wenn Sie den Scanner oder Drucker in einem Netzwerk verwenden, wird das Dialogfeld Einstellungen (Auf PC speichern (automatisch)) (Settings (Save to PC (Auto))) nicht angezeigt.
Dialogfeld Einstellungen (Automatisch scannen) Klicken Sie auf der Registerkarte (Scannen über den Computer) auf Automatisch scannen (Auto Scan), um das Dialogfeld Einstellungen (Automatisch scannen) (Settings (Auto Scan)) anzuzeigen. Im Dialogfeld Einstellungen (Automatisch scannen) (Settings (Auto Scan)) können Sie erweiterte Scaneinstellungen vornehmen, um mit automatischer Erkennung des Objekttyps zu scannen.
Einstellungen (Benutzerdefiniert scannen) (Settings (Custom Scan)) an, und klicken Sie dann im Hauptbildschirm von IJ Scan Utility auf Foto (Photo), Dokument (Document) oder Benutzerdef. (Custom). Folgende Objekte können mit Automatisch (Auto) nicht ordnungsgemäß gescannt werden. Fotos im Format A4 Textdokumente, die kleiner als 2L (127 mm x 178 mm) (5 Zoll x 7 Zoll) sind, z. B.
Geben Sie den Dateinamen des zu speichernden Bilds ein. Wenn Sie eine Datei speichern, werden das Datum und vier Ziffern im Format "_20XX0101_0001" angehängt. • Datenformat (Data Format) Automatisch (Auto) ist ausgewählt. Die folgenden Datenformate werden beim Speichern automatisch gemäß dem Objekttyp angewendet. - Fotos, Postkarten, BDs/DVDs/CDs und Visitenkarten: JPEG - Zeitschriften, Zeitungen und Dokumente: PDF Wichtig Das Speicherformat kann je nach Platzierung des Objekts unterschiedlich sein.
Wählen Sie die Option aus, wenn Sie die gescannten Bilder verbessern oder korrigieren möchten. Sie können die Anwendung über das Pull-Down-Menü angeben. • An Anwendung senden (Send to an application) Wählen Sie diese Option aus, wenn Sie die gescannten Bilder unverändert in einer Anwendung verwenden möchten, in der Sie die Bilder durchsuchen oder organisieren können. Sie können die Anwendung über das Pull-Down-Menü angeben.
Dialogfeld Einstellungen (Foto scannen) Klicken Sie auf der Registerkarte (Scannen über den Computer) auf Foto scannen (Photo Scan), um das Dialogfeld Einstellungen (Foto scannen) (Settings (Photo Scan)) anzuzeigen. Im Dialogfeld Einstellungen (Foto scannen) (Settings (Photo Scan)) können Sie erweiterte Einstellungen für das Scannen von Objekten als Fotos festlegen.
• Farbmodus (Color Mode) Wählen Sie den Farbmodus, in dem das Objekt gescannt werden soll. Wichtig Deaktivieren Sie zum Auswählen von Schwarzweiß (Black and White) das Kontrollkästchen Gescannte Bilder beim Übertragen komprimieren (Compress scanned images upon transfer). • Papierformat (Paper Size) Wählen Sie die Größe des zu scannenden Objekts aus. Wenn Sie die Option Benutzerdefiniert (Custom) auswählen, wird ein Bildschirm angezeigt, in dem Sie das Papierformat angeben können.
Wichtig Ist für Farbmodus (Color Mode) die Option Schwarzweiß (Black and White) festgelegt, ist Bildverarbeitungs-Einstellungen (Image Processing Settings) nicht verfügbar. • Kontor schärfen (Sharpen outline) Verstärkt die Konturen der Motive, um die Bildschärfe zu erhöhen. (2) Bereich Speichereinstellungen • Dateiname (File Name) Geben Sie den Dateinamen des zu speichernden Bilds ein. Wenn Sie eine Datei speichern, werden das Datum und vier Ziffern im Format "_20XX0101_0001" angehängt.
Wichtig Wenn das Dialogfeld Einstellungen über My Image Garden geöffnet wird, wird diese Option nicht angezeigt. • Scanergebnisse prüfen (Check scan results) Zeigt das Dialogfeld Speichereinstellungen (Save Settings) nach dem Scannen an. Wichtig Wenn das Dialogfeld Einstellungen über My Image Garden geöffnet wird, wird diese Option nicht angezeigt.
• Anweisungen (Instructions) Öffnet dieses Handbuch. • Standard (Defaults) Sie können die Einstellungen im angezeigten Bildschirm auf die Standardeinstellungen zurücksetzen.
Dialogfeld Einstellungen (Dokument scannen) Klicken Sie auf der Registerkarte (Scannen über den Computer) auf Dokument scannen (Document Scan), um das Dialogfeld Einstellungen (Dokument scannen) (Settings (Document Scan)) anzuzeigen. Im Dialogfeld Einstellungen (Dokument scannen) (Settings (Document Scan)) können Sie erweiterte Einstellungen für das Scannen von Objekten als Dokumente festlegen.
Dokumente scannen: Dokument (Document) Zeitschriften scannen: Zeitschrift (Magazine) • Farbmodus (Color Mode) Wählen Sie den Farbmodus, in dem das Objekt gescannt werden soll. Wichtig Deaktivieren Sie zum Auswählen von Schwarzweiß (Black and White) das Kontrollkästchen Gescannte Bilder beim Übertragen komprimieren (Compress scanned images upon transfer). • Papierformat (Paper Size) Wählen Sie die Größe des zu scannenden Objekts aus.
• Bildverarbeitungs-Einstellungen (Image Processing Settings) Klicken Sie auf (Plus), um Folgendes festzulegen. Hinweis Wenn Farbmodus (Color Mode) auf Schwarzweiß (Black and White) festgelegt ist, werden nur Bundstegschatten verringern (Reduce gutter shadow), Schräge Textdokumente korrigieren (Correct slanted text document) und Ausrichtung von Textdokumenten erkennen und Bilder drehen (Detect the orientation of text document and rotate image) angezeigt.
• Bundstegschatten verringern (Reduce gutter shadow) Reduziert Bundstegschatten, die beim Scannen von geöffneten Broschüren zwischen den Seiten auftreten. Wichtig Ist nur verfügbar, wenn das Kontrollkästchen Gescannte Bilder beim Übertragen komprimieren (Compress scanned images upon transfer) nicht aktiviert ist.
Wichtig Es werden nur Textdokumente in den Sprachen unterstützt, die unter Sprache des Dokuments (Document Language) im Dialogfeld Einstellungen (Allgemeine Einstellungen) (Settings (General Settings)) ausgewählt werden können. Die Ausrichtung kann bei den folgenden Einstellungs- und Dokumenttypen möglicherweise nicht erkannt werden, da der Text nicht ordnungsgemäß erkannt werden kann.
• Speichern in (Save in) Zeigt den Ordner an, in dem die gescannten Bilder gespeichert werden sollen. Geben Sie zum Ändern des Ordners den Zielordner im Dialogfeld Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können. Die folgenden Ordner werden standardmäßig zum Speichern angegeben.
Wählen Sie die Option aus, wenn Sie die gescannten Bilder an E-Mails anhängen möchten. Sie können das zu startende E-Mail-Programm aus dem Pull-Down-Menü auswählen. • OCR starten (Start OCR) Wählen Sie diese Option, wenn Sie Text im Bild mit einer bestimmten OCR-Software in Textdaten konvertieren möchten. Sie können die Anwendung über das Pull-Down-Menü angeben. • Keine Anwendung starten (Do not start any application) Das Speichern erfolgt in dem unter Speichern in (Save in) angegebenen Ordner.
Dialogfeld Einstellungen (Benutzerdefiniert scannen) Klicken Sie auf der Registerkarte (Scannen über den Computer) auf Benutzerdefiniert scannen (Custom Scan), um das Dialogfeld Einstellungen (Benutzerdefiniert scannen) (Settings (Custom Scan)) anzuzeigen. Im Dialogfeld Einstellungen (Benutzerdefiniert scannen) (Settings (Custom Scan)) können Sie erweiterte Einstellungen für das Scannen mit Ihren bevorzugten Einstellungen festlegen.
Wählen Sie den Typ des zu scannenden Objekts. Wenn Automatisch (Auto) ausgewählt ist, wird der Objekttyp automatisch erkannt. In diesem Fall werden auch Farbmodus (Color Mode), Papierformat (Paper Size) und Auflösung (Resolution) automatisch festgelegt. Wichtig Folgende Objekttypen werden von der Einstellung Automatisch (Auto) unterstützt: Fotos, Postkarten, Visitenkarten, Zeitschriften, Zeitungen, Dokumente und BDs/ DVDs/CDs.
Hinweis Ist für Quelle wählen (Select Source) die Option Automatisch (Auto) ausgewählt, ist nur Farbe (Color) verfügbar. • Papierformat (Paper Size) Wählen Sie die Größe des zu scannenden Objekts aus. Wenn Sie die Option Benutzerdefiniert (Custom) auswählen, wird ein Bildschirm angezeigt, in dem Sie das Papierformat angeben können. Wählen Sie eine Option für Einheit (Unit), geben Sie die Breite (Width) und Höhe (Height) an, und klicken Sie dann auf OK.
Wichtig Wird nicht angezeigt, wenn Quelle wählen (Select Source) auf Automatisch (Auto) gesetzt ist. • Bildverarbeitungs-Einstellungen (Image Processing Settings) Klicken Sie auf (Plus), um Folgendes festzulegen. Die verfügbaren Einstellungselemente hängen von der Option Quelle wählen (Select Source) ab.
Aktivieren Sie dieses Kontrollkästchen, um den Text in einem Dokument oder Magazin zu schärfen und dadurch besser lesbar zu machen. Wichtig Ist nur verfügbar, wenn das Kontrollkästchen Gescannte Bilder beim Übertragen komprimieren (Compress scanned images upon transfer) nicht aktiviert ist. Der Farbton kann aufgrund der Korrekturen von dem des Originalbilds abweichen. Deaktivieren Sie in diesem Fall das Kontrollkästchen und scannen Sie.
Hinweis Sie können Bundstegschatten auf der Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear (Scanner-Treiber) korrigieren, wenn Sie Objekte scannen, bei deren Format es sich nicht um ein Standardformat handelt, oder wenn bestimmte Bereiche angegeben wurden. Weitere Informationen finden Sie auf der Startseite des Online-Handbuchs im Abschnitt "Bundstegschattenkorrektur" des entsprechenden Modells.
Die Auflösung liegt außerhalb des Bereichs von 300 bis 600 dpi Die Schriftgröße liegt außerhalb des Bereichs von 8 bis 48 Punkt Dokumente, die spezielle Schriftarten, Effekte, Kursiv- oder handschriftlichen Text enthalten Dokumente mit gemustertem Hintergrund Aktivieren Sie in diesem Fall das Kontrollkästchen Scanergebnisse prüfen (Check scan results) und drehen Sie das Bild im Dialogfeld Speichereinstellungen (Save Settings).
Zeigt den Ordner an, in dem die gescannten Bilder gespeichert werden sollen. Geben Sie zum Ändern des Ordners den Zielordner im Dialogfeld Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können. Die folgenden Ordner werden standardmäßig zum Speichern angegeben.
Wählen Sie die Option aus, wenn Sie die gescannten Bilder an E-Mails anhängen möchten. Sie können das zu startende E-Mail-Programm aus dem Pull-Down-Menü auswählen. • OCR starten (Start OCR) Wählen Sie diese Option, wenn Sie Text im Bild mit einer bestimmten OCR-Software in Textdaten konvertieren möchten. Sie können die Anwendung über das Pull-Down-Menü angeben. • Keine Anwendung starten (Do not start any application) Das Speichern erfolgt in dem unter Speichern in (Save in) angegebenen Ordner.
Dialogfeld Einstellungen (Scannen und zusammenfügen) Klicken Sie auf der Registerkarte (Scannen über den Computer) auf Scannen und zusammenfügen (Scan and Stitch), um das Dialogfeld Einstellungen (Scannen und zusammenfügen) (Settings (Scan and Stitch)) anzuzeigen. Im Dialogfeld Einstellungen (Scannen und zusammenfügen) (Settings (Scan and Stitch)) können Sie erweiterte Einstellungen für das Scannen von Objekten festlegen, die größer als die Auflagefläche sind.
Zeitschriften scannen: Zeitschrift (Magazine) Hinweis Um den Moiré-Effekt zu reduzieren, setzen Sie Quelle wählen (Select Source) auf Zeitschrift (Magazine). • Farbmodus (Color Mode) Wählen Sie den Farbmodus, in dem das Objekt gescannt werden soll. • Auflösung (Resolution) Wählen Sie die Auflösung des zu scannenden Objekts aus. Je höher der Wert für die Auflösung, desto detailreicher ist das Bild. Auflösung • Bildverarbeitungs-Einstellungen (Image Processing Settings) (Plus), um Folgendes festzulegen.
Hinweis Das Scannen dauert länger als gewöhnlich, wenn Sie Moiré reduzieren (Reduce moire) aktivieren. (2) Bereich Speichereinstellungen • Dateiname (File Name) Geben Sie den Dateinamen des zu speichernden Bilds ein. Wenn Sie eine Datei speichern, werden das Datum und vier Ziffern im Format "_20XX0101_0001" angehängt. • Datenformat (Data Format) Wählen Sie das Datenformat, in dem die gescannten Bilder gespeichert werden sollen.
Zeigt das Dialogfeld Speichereinstellungen (Save Settings) nach dem Scannen an. Wichtig Wenn das Dialogfeld Einstellungen über My Image Garden geöffnet wird, wird diese Option nicht angezeigt. (3) Bereich Anwendungseinstellungen • Mit Anwendung öffnen (Open with an application) Wählen Sie die Option aus, wenn Sie die gescannten Bilder verbessern oder korrigieren möchten. Sie können die Anwendung über das Pull-Down-Menü angeben.
Dialogfeld Einstellungen (ScanGear) Klicken Sie auf der Registerkarte (Scannen über den Computer) auf ScanGear, um das Dialogfeld Einstellungen (ScanGear) (Settings (ScanGear)) anzuzeigen. Im Dialogfeld Einstellungen (ScanGear) (Settings (ScanGear)) können Sie angeben, wie Bilder beim Scannen mit ScanGear (Scanner-Treiber) gespeichert werden sollen und das Verhalten nach dem Scannen festlegen.
Sie können JPEG/Exif, TIFF, PNG, PDF oder PDF (Mehrere Seiten) (PDF (Multiple Pages)) auswählen. Hinweis Wenn PDF oder PDF (Mehrere Seiten) (PDF (Multiple Pages)) ausgewählt ist, können Bilder mit maximal 9.600 Pixel x 9.600 Pixel gescannt werden.
Hinweis Wenn dieses Kontrollkästchen nicht aktiviert ist, können Bilder mit maximal 10.208 Pixel x 14.032 Pixel gescannt werden. • Scanergebnisse prüfen (Check scan results) Zeigt das Dialogfeld Speichereinstellungen (Save Settings) nach dem Scannen an. Wichtig Wenn das Dialogfeld Einstellungen über My Image Garden geöffnet wird, wird diese Option nicht angezeigt.
Hinweis Geben Sie die Anwendung oder den Ordner im Dialogfeld Anwendung auswählen (Select Application) oder Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können. • Anweisungen (Instructions) Öffnet dieses Handbuch. • Standard (Defaults) Sie können die Einstellungen im angezeigten Bildschirm auf die Standardeinstellungen zurücksetzen.
Dialogfeld Einstellungen (Auf PC speichern (automatisch)) Klicken Sie auf der Registerkarte (Scannen über das Bedienfeld) auf Auf PC speichern (automatisch) (Save to PC (Auto)), um das Dialogfeld Einstellungen (Auf PC speichern (automatisch)) (Settings (Save to PC (Auto))) anzuzeigen.
• Empfohlene Bildkorrektur übernehmen (Apply recommended image correction) Wendet für jeden Objekttyp automatisch die geeigneten Korrekturen an. Wichtig Der Farbton kann aufgrund der Korrekturen von dem des Originalbilds abweichen. Deaktivieren Sie in diesem Fall das Kontrollkästchen und scannen Sie. Hinweis Der Scan-Vorgang dauert länger als gewöhnlich, wenn Sie diese Funktion aktivieren. (2) Bereich Speichereinstellungen • Dateiname (File Name) Geben Sie den Dateinamen des zu speichernden Bilds ein.
Zeigt den Ordner an, in dem die gescannten Bilder gespeichert werden sollen. Geben Sie zum Ändern des Ordners den Zielordner im Dialogfeld Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können. Die folgenden Ordner werden standardmäßig zum Speichern angegeben.
Dialogfeld Einstellungen (Auf PC speichern (Foto)) Klicken Sie auf der Registerkarte (Scannen über das Bedienfeld) auf Auf PC speichern (Foto) (Save to PC (Photo)), um das Dialogfeld Einstellungen (Auf PC speichern (Foto)) (Settings (Save to PC (Photo))) anzuzeigen. Im Dialogfeld Einstellungen (Auf PC speichern (Foto)) (Settings (Save to PC (Photo))) können Sie das Verhalten für das Speichern von Bildern als Fotos auf dem Computer festlegen, nachdem diese über das Bedienfeld gescannt wurden.
(2) Bereich Speichereinstellungen • Dateiname (File Name) Geben Sie den Dateinamen des zu speichernden Bilds ein. Wenn Sie eine Datei speichern, werden das Datum und vier Ziffern im Format "_20XX0101_0001" angehängt. • Datenformat (Data Format) Wird über das Bedienfeld festgelegt. • Einst... (Settings...
Sie können den Ordner über das Pull-Down-Menü angeben. • Keine Anwendung starten (Do not start any application) Das Speichern erfolgt in dem unter Speichern in (Save in) angegebenen Ordner. Hinweis Geben Sie die Anwendung oder den Ordner im Dialogfeld Anwendung auswählen (Select Application) oder Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können. • Anweisungen (Instructions) Öffnet dieses Handbuch.
Dialogfeld Einstellungen (Auf PC speichern (Dokument)) Klicken Sie auf der Registerkarte (Scannen über das Bedienfeld) auf Auf PC speichern (Dokument) (Save to PC (Document)), um das Dialogfeld Einstellungen (Auf PC speichern (Dokument)) (Settings (Save to PC (Document))) anzuzeigen.
• Bildverarbeitungs-Einstellungen (Image Processing Settings) Klicken Sie auf (Plus), um Folgendes festzulegen. • Automatische Dokumentkorrektur anwenden (Apply Auto Document Fix) Aktivieren Sie dieses Kontrollkästchen, um den Text in einem Dokument oder Magazin zu schärfen und dadurch besser lesbar zu machen. Wichtig Ist nur verfügbar, wenn das Kontrollkästchen Gescannte Bilder beim Übertragen komprimieren (Compress scanned images upon transfer) nicht aktiviert ist.
Dokumente, die sowohl vertikale als auch horizontale Zeilen (Tabellen) enthalten Hinweis Das Scannen dauert länger als gewöhnlich, wenn Sie Schräge Textdokumente korrigieren (Correct slanted text document) aktivieren. • Ausrichtung von Textdokumenten erkennen und Bilder drehen (Detect the orientation of text document and rotate image) Erkennt die Ausrichtung des Texts im gescannten Dokument und dreht das Bild in die richtige Ausrichtung.
Zeigt den Ordner an, in dem die gescannten Bilder gespeichert werden sollen. Geben Sie zum Ändern des Ordners den Zielordner im Dialogfeld Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können. Die folgenden Ordner werden standardmäßig zum Speichern angegeben.
Sie können die Einstellungen im angezeigten Bildschirm auf die Standardeinstellungen zurücksetzen.
Dialogfeld Einstellungen (An E-Mail anhängen (Foto)) Klicken Sie auf der Registerkarte (Scannen über das Bedienfeld) auf An E-Mail anhängen (Foto) (Attach to E-mail (Photo)), um das Dialogfeld Einstellungen (An EMail anhängen (Foto)) (Settings (Attach to E-mail (Photo))) anzuzeigen.
(2) Bereich Speichereinstellungen • Dateiname (File Name) Geben Sie den Dateinamen des zu speichernden Bilds ein. Wenn Sie eine Datei speichern, werden das Datum und vier Ziffern im Format "_20XX0101_0001" angehängt. • Datenformat (Data Format) Wird über das Bedienfeld festgelegt. • Einst... (Settings...
Sie können die Einstellungen im angezeigten Bildschirm auf die Standardeinstellungen zurücksetzen.
Dialogfeld Einstellungen (An E-Mail anhängen (Dokument)) Klicken Sie auf der Registerkarte (Scannen über das Bedienfeld) auf An E-Mail anhängen (Dokument) (Attach to E-mail (Document)), um das Dialogfeld Einstellungen (An E-Mail anhängen (Dokument)) (Settings (Attach to E-mail (Document))) anzuzeigen.
Komprimiert gescannte Bilder beim Übertragen auf einen Computer. Dies ist hilfreich, wenn der Scanner oder Drucker über eine langsame Schnittstelle, z. B. USB1.1, oder über ein Netzwerk mit dem Computer verbunden ist. • Bildverarbeitungs-Einstellungen (Image Processing Settings) Klicken Sie auf (Plus), um Folgendes festzulegen.
Dokumente mit wenig Text Dokumente, die Abbildungen/Bilder enthalten Handschriftlicher Text Dokumente, die sowohl vertikale als auch horizontale Zeilen (Tabellen) enthalten Hinweis Das Scannen dauert länger als gewöhnlich, wenn Sie Schräge Textdokumente korrigieren (Correct slanted text document) aktivieren.
Schlüsselwortsuche für PDF-Dateien sowie das Datenformat für das Speichern von automatisch gescannten Bildern festlegen können. • Speichern in (Save in) Zeigt den Ordner an, in dem die gescannten Bilder gespeichert werden sollen. Zum Ändern des Ordners klicken Sie auf Hinzufügen... (Add...) und geben den Zielordner dann im Dialogfeld Speicherort auswählen (Select Destination Folder) an. Die folgenden Ordner werden standardmäßig zum Speichern angegeben.
Dialogfeld Einstellungen (Allgemeine Einstellungen) Klicken Sie auf die Registerkarte (Allgemeine Einstellungen), um das Dialogfeld Einstellungen (Allgemeine Einstellungen) (Settings (General Settings)) anzuzeigen. Im Dialogfenster Einstellungen (Allgemeine Einstellungen) (Settings (General Settings)) können Sie das zu verwendende Produkt, die Dateigrößenbeschränkung für EMail-Anhänge, die Sprache für die Erkennung von Text in Bildern und einen Ordner für das vorübergehende Speichern von Bildern festlegen.
Sie können Klein (für Fenster mit 640 x 480 geeignet) (Small (Suitable for 640 x 480 Windows)), Mittel (für Fenster mit 800 x 600 geeignet) (Medium (Suitable for 800 x 600 Windows)), Groß (für Fenster mit 1024 x 768 geeignet) (Large (Suitable for 1024 x 768 Windows)) oder Keine Änderung (No Change) auswählen. Wichtig Wenn das Dialogfeld Einstellungen über My Image Garden geöffnet wird, wird diese Option nicht angezeigt.
Dialogfeld Datenformateinstellungen Zeigen Sie mithilfe einer der folgenden Methoden das Dialogfeld Datenformateinstellungen (Data Format Settings) an. • Klicken auf Einstellungen... (Settings...) unter Speichereinstellungen (Save Settings) auf jeder Registerkarte des Dialogfelds Einstellungen • Klicken auf Einstellungen... (Settings...
• PDF-Komprimierung (PDF Compression) Wählen Sie den Komprimierungstyp zum Speichern von PDF-Dateien aus. • Standard Es wird empfohlen, diese Einstellung grundsätzlich zu verwenden. • Hoch (High) Komprimiert die Dateigröße beim Speichern, so dass die Last auf Ihrem Netzwerk/ Server verringert wird.
Dialogfeld Speichereinstellungen Aktivieren Sie das Kontrollkästchen Scanergebnisse prüfen (Check scan results) unter Speichereinstellungen (Save Settings) im Dialogfeld Einstellungen, um nach dem Scannen das Dialogfeld Speichereinstellungen (Save Settings) anzuzeigen. Sie können das Datenformat und das Ziel festlegen, während Sie sich die Scanergebnisse in Miniaturansicht ansehen.
Wichtig Die Bedienschaltflächen der Vorschau werden nicht angezeigt, wenn das Kontrollkästchen Großformatige Bildscans aktivieren (Enable large image scans) im Dialogfeld Einstellungen (ScanGear) (Settings (ScanGear)) aktiviert ist. (2) Bereich Scanergebnisse Zeigt die Miniaturansichten der gescannten Bilder an. Sie können die Speicherreihenfolge von Bildern per Drag & Drop ändern. Die Dateinamen für das Speichern werden unter den Miniaturansichten angezeigt.
Schlüsselwortsuche für PDF-Dateien und ihren Komprimierungstyp sowie das Datenformat für das Speichern von automatisch gescannten Bildern festlegen können. • Speichern in (Save in) Zeigt den Ordner an, in dem die gescannten Bilder gespeichert werden sollen. Geben Sie zum Ändern des Ordners den Zielordner im Dialogfeld Speicherort auswählen (Select Destination Folder) an, das Sie durch Auswählen von Hinzufügen... (Add...) im Pull-Down-Menü anzeigen können.
Fenster Bild zusammenfügen Klicken Sie im Hauptbildschirm von IJ Scan Utility auf Zusammenf. (Stitch), um das Fenster Bild zusammenfügen (Image Stitch) anzuzeigen. Sie können die rechten und linken Hälften eines Objekts, das größer als die Auflagefläche ist, scannen und die gescannten Bilder anschließend zu einem Bild zusammenfügen. Sie können Objekte scannen, die etwa doppelt so groß wie die Auflagefläche sind.
Scannt die linke und die rechte Hälfte eines Objekts, das doppelt so groß wie das Letter-Format ist, separat. • Ganze Auflagefläche x 2 (Full Platen x 2) Scannt die linke und die rechte Hälfte eines Objekts, das doppelt so groß wie die Auflagefläche ist, separat. • Scanrichtung (Scan Direction) • Von links scannen (Scan from Left) Zeigt das erste gescannte Bild auf der linken Seite an. • Von rechts scannen (Scan from Right) Zeigt das erste gescannte Bild auf der rechten Seite an.
• Schnittrahmen anpassen (Adjust cropping frames) Sie können den Scan-Bereich in der Vorschau anpassen. Wird kein Bereich festgelegt, wird das Bild in der Größe gespeichert, die unter Ausgabegröße wählen (Select Output Size) ausgewählt ist. Wird ein Bereich festgelegt, wird nur das Bild im Schnittrahmen gescannt und gespeichert. Anpassen von Schnittrahmen im Fenster Bild zusammenfügen • Speichern (Save) • Speichern (Save) Speichert die beiden gescannten Bilder als ein Bild.
Klicken Sie mit der rechten Maustaste in den Vorschaubereich, um das angezeigte Bild zu verkleinern. • (Nach links drehen) Das Vorschaubild wird um 90 Grad gegen den Uhrzeigersinn gedreht. • (Vertikal invertieren) Das Vorschaubild wird um 180 Grad gedreht. • (Nach rechts drehen) Das Vorschaubild wird um 90 Grad im Uhrzeigersinn gedreht. • (Handbuch öffnen) Öffnet diese Seite. (3) Miniaturansichtsbereich • Miniaturansichtsbereich Zeigt die Miniaturansichten der gescannten Bilder an.
• Nach dem Scannen des ersten Objekts durch Klicken auf Scannen von Bild 1 beginnen (Start Scanning Image 1) Das Bild wird in der unter Scanrichtung (Scan Direction) festgelegten Richtung gescannt, und 2 wird neben dem Bild angezeigt. • Nach dem Scannen des zweiten Objekts durch Klicken auf Scannen von Bild 2 beginnen (Start Scanning Image 2) Die beiden gescannten Bilder werden angezeigt.
Scannen mit verwendeter Anwendungssoftware (ScanGear) Was ist ScanGear (Scanner-Treiber)? Mit den erweiterten Einstellungen von ScanGear (Scanner-Treiber) scannen ScanGear (Scanner-Treiber) starten Im Basismodus scannen Im erweiterten Modus scannen Mehrere Dokumente gleichzeitig mit ScanGear (Scanner-Treiber) scannen Mit ScanGear (Scanner-Treiber) Bilder korrigieren und Farben anpassen Bildschirme von ScanGear (Scanner-Treiber) Objekte platzieren (beim Scannen über den Computer) Schnittrahmen anpassen (Scan
Was ist ScanGear (Scanner-Treiber)? ScanGear (Scanner-Treiber) ist Software, die zum Scannen von Dokumenten benötigt wird. Mit dieser Software können Sie vor dem Scannen von Dokumenten das Ausgabeformat festlegen und Bildkorrekturen vornehmen. ScanGear kann über My Image Garden oder IJ Scan Utility gestartet werden. Die Software kann ebenfalls von anderen Anwendungen aus gestartet werden, sofern diese mit der Standardschnittstelle TWAIN kompatibel sind. (ScanGear ist ein TWAIN-kompatibler Treiber.
Erweiterter Modus Auf der Registerkarte Erweiterter Modus (Advanced Mode) können Sie den Farbmodus, die Ausgabeauflösung, die Helligkeit, den Farbton usw. für den Scan-Vorgang einstellen.
Mit den erweiterten Einstellungen von ScanGear (Scanner-Treiber) scannen ScanGear (Scanner-Treiber) starten ScanGear (Scanner-Treiber) starten Dokumente nach einfachen Bildkorrekturen scannen Im Basismodus scannen Dokumente nach komplexeren Bildkorrekturen und Helligkeits-/Farbanpassungen scannen Im erweiterten Modus scannen Mehrere Dokumente gleichzeitig nach Bildkorrekturen und Farbanpassungen scannen Mehrere Dokumente gleichzeitig mit ScanGear (Scanner-Treiber) scannen 106
ScanGear (Scanner-Treiber) starten Verwenden Sie ScanGear (Scanner-Treiber), um beim Scannen Bild- und Farbkorrekturen vorzunehmen. ScanGear kann über My Image Garden oder andere Anwendungen gestartet werden. Starten über My Image Garden Befolgen Sie diese Schritte, um ScanGear über My Image Garden zu starten. 1. Starten Sie My Image Garden. Anleitungen zum Starten von My Image Garden finden Sie im Handbuch zu My Image Garden. 2.
Im Basismodus scannen Verwenden Sie die Registerkarte Basismodus (Basic Mode), um mit einer einfachen Methode zu scannen, indem Sie die Anweisungen auf dem Bildschirm befolgen. Weitere Informationen über das Scannen mehrerer Dokumente gleichzeitig finden Sie unter "Mehrere Dokumente gleichzeitig mit ScanGear (Scanner-Treiber) scannen".
Hinweis Um Zeitschriften mit vielen Farbfotos zu scannen, wählen Sie Zeitschrift (Farbe) (Magazine (Color)). 3. Klicken Sie auf Vorschau (Preview). Das Vorschaubild wird im Vorschaubereich angezeigt. Hinweis Die Farben werden entsprechend dem Dokumenttyp angepasst, der unter Quelle wählen (Select Source) ausgewählt wurde. 4. Wählen Sie das Ziel (Destination).
5. Legen Sie das Ausgabeformat (Output Size) dem Zweck entsprechend fest. Die hier verfügbaren Optionen sind davon abhängig, welche Einstellung unter Ziel (Destination) ausgewählt wurde. 6. Legen Sie die Schnittrahmen (Scan-Bereiche) wie gewünscht fest. Passen Sie die Größe und Position der Schnittrahmen auf dem Vorschaubild an. Schnittrahmen anpassen (ScanGear) 7. Legen Sie die erforderlichen Bildkorrekturen (Image corrections) fest. 8. Klicken Sie auf Scannen (Scan). Der Scan-Vorgang wird gestartet.
Im erweiterten Modus scannen Auf der Registerkarte Erweiterter Modus (Advanced Mode) können Sie den Farbmodus, die Ausgabeauflösung, die Helligkeit, den Farbton usw. für den Scan-Vorgang einstellen. Weitere Informationen über das Scannen mehrerer Dokumente gleichzeitig finden Sie unter "Mehrere Dokumente gleichzeitig mit ScanGear (Scanner-Treiber) scannen".
Hinweis Wenn Sie zwischen den Modi wechseln, werden die vorgenommenen Einstellungen nicht beibehalten. 3. Legen Sie die Eingabe-Einstellungen (Input Settings) je nach Dokument oder Zweck fest. 4. Klicken Sie auf Vorschau (Preview). Das Vorschaubild wird im Vorschaubereich angezeigt. 5. Legen Sie die Ausgabe-Einstellungen (Output Settings) fest.
6. Passen Sie bei Bedarf den Schnittrahmen (Scan-Bereich) an, und nehmen Sie Bild- und Farbkorrekturen vor. Schnittrahmen anpassen (ScanGear) Bildeinstellungen Schaltflächen für die Farbeinstellung 7. Klicken Sie auf Scannen (Scan). Der Scan-Vorgang wird gestartet. Hinweis Klicken Sie auf (Information), um das Dialogfeld zu öffnen, in dem Sie die aktuellen Scaneinstellungen (Dokumenttyp usw.) überprüfen können.
Mehrere Dokumente gleichzeitig mit ScanGear (ScannerTreiber) scannen Mit der Registerkarte Basismodus (Basic Mode) und Erweiterter Modus (Advanced Mode) können Sie zwei oder mehr Fotos (kleine Dokumente) auf der Auflagefläche gleichzeitig scannen. In diesem Abschnitt wird erläutert, wie Sie mehrere Dokumente mithilfe der Registerkarte Basismodus (Basic Mode) scannen. Wichtig Um mehrere Dokumente als ein einziges Bild zu scannen, führen Sie den ScanVorgang in der Gesamtbildansicht durch.
2. Wählen Sie unter Quelle wählen (Select Source) den zu scannenden Dokumenttyp aus. 3. Klicken Sie auf Vorschau (Preview). Im Vorschaubereich werden Miniaturansichten der Vorschaubilder angezeigt. Es werden automatisch Schnittrahmen entsprechend der Dokumentgröße festgelegt. 4. Wählen Sie das Ziel (Destination). 5. Legen Sie das Ausgabeformat (Output Size) dem Zweck entsprechend fest.
6. Passen Sie die Schnittrahmen wie gewünscht an und legen Sie Bildkorrekturen (Image corrections) fest. Hinweis Sie können jedes Bild einzeln korrigieren. Wählen Sie das Bild aus, das Sie korrigieren möchten. In der Miniaturansicht können Sie nur einen Schnittrahmen pro Bild erstellen. Um in einem Bild mehrere Schnittrahmen zu erstellen, führen Sie den ScanVorgang in der Gesamtbildansicht durch. Mehrere Dokumente gleichzeitig in der Gesamtbildansicht scannen 7.
Hinweis Wenn das Gesamtbild angezeigt wird, ändert sich das Symbol in (Gesamtbild). 2. Wählen Sie das Ziel (Destination). 3. Legen Sie das Ausgabeformat (Output Size) dem Zweck entsprechend fest. Seitenverhältnis umkehren (Invert aspect ratio) ist aktiviert, wenn Ausgabeformat (Output Size) auf eine andere Einstellung als Flexibel (Flexible) gesetzt ist. Klicken Sie auf diese Schaltfläche, um den Schnittrahmen zu drehen. Klicken Sie erneut darauf, um die ursprüngliche Ausrichtung wiederherzustellen. 4.
Hinweis Im Dialogfeld Voreinstellungen (Preferences) kann auf der Registerkarte Scannen (Scan) unter Status des ScanGear-Dialogfelds nach dem Scannen (Status of ScanGear dialog after scanning) eine Antwort von ScanGear nach dem Scannen angegeben werden.
Mit ScanGear (Scanner-Treiber) Bilder korrigieren und Farben anpassen Fotos schärfen, Staub und Kratzer reduzieren und verblasste Farben korrigieren Bilder korrigieren (Scharfzeichnen, Staub und Kratzer reduzieren, Farbkorrektur usw.) Vorschau des zu scannenden Bilds anzeigen und den Farbton ändern Farben mithilfe eines Farbmusters anpassen Bilder aufhellen, die mit der Zeit verblasst sind oder einen Farbstich haben Sättigung und Farbbalance anpassen Zu dunkle oder zu helle bzw.
Bilder korrigieren (Scharfzeichnen, Staub und Kratzer reduzieren, Farbkorrektur usw.) Mit den Funktionen unter Bildeinstellungen (Image Settings) auf der Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear (Scanner-Treiber) können Sie beim Scannen von Bildern die Konturen von Motiven verbessern, Staub oder Kratzer reduzieren und verblasste Farben korrigieren. Optionen festlegen Klicken Sie auf das Symbol einen Eintrag aus.
Hinweis Informationen dazu, wie Sie die Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear öffnen und damit scannen, finden Sie im Abschnitt "Im erweiterten Modus scannen". Helligkeit und Farbton des Bilds anpassen Legen Sie unter Bildanpassung (Image Adjustment) je nach Dokumenttyp Automatisch (Auto), Foto (Photo), Zeitschrift (Magazine) oder Dokument (Document) fest.
Farbverläufe und Streifen reduzieren Setzen Sie die Option Entrastern (Descreen) auf EIN (ON). AUS (OFF) EIN (ON) Hinweis Gedruckte Fotos und Bilder werden durch eine Ansammlung feiner Punkte wiedergegeben. Moiré ist ein Effekt, bei dem die Farbverläufe des Bildes ungleichmäßig werden und ein Streifenmuster auf dem Bild entsteht, wenn Fotos oder Bilder mit feinen Punkten gescannt werden. Mit der Funktion Entrastern (Descreen) wird der MoiréEffekt reduziert.
Körnigkeit reduzieren Setzen Sie je nach Grad der Körnigkeit die Option Bildglättung (Grain Correction) auf Niedrig (Low), Mittel (Medium) oder Hoch (High). Ohne (None) Mittel (Medium) Schatten beheben, die beim Scannen von geöffneten Broschüren zwischen den Seiten auftreten Setzen Sie je nach Stärke der Schatten die Option Bundstegschattenkorrektur (Gutter Shadow Correction) auf Niedrig (Low), Mittel (Medium) oder Hoch (High).
Farben mithilfe eines Farbmusters anpassen Auf der Registerkarte Basismodus (Basic Mode) von ScanGear (Scanner-Treiber) können Sie mit der Farbmusterfunktion Farbänderungen in der Vorschau anzeigen und natürliche Farben reproduzieren. Farbeinstellung Sie können Bilder korrigieren, die mit der Zeit verblasst sind oder einen Farbstich haben. Ein "Farbstich" entsteht, wenn eine Farbe aufgrund der Wetterverhältnisse bei der Aufnahme oder aufgrund starker Umgebungsfarben ein Bild dominiert.
Zyan und Rot, Magenta und Grün sowie Gelb und Blau sind komplementäre Farbpaare (bei Mischung der einzelnen Farbpaare werden verschiedene Grautöne erzeugt). Sie können die natürliche Farbe reproduzieren, indem Sie die Farbe verringern, die den Stich hervorruft, und die Komplementärfarbe verstärken. Es wird empfohlen, einen Bildbereich auszuwählen, der weiß sein sollte, und die Farben so anzupassen, dass dieser Bildbereich weiß wird. Das Vorschaubild wird in der Mitte angezeigt.
Sättigung und Farbbalance anpassen Klicken Sie auf der Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear (Scanner-Treiber) auf (Sättigung/Farbbalance). Hinweis Klicken Sie auf Standard (Defaults), um alle Anpassungen im aktuellen Fenster rückgängig zu machen. Sättigung Passen Sie die Sättigung bzw. Leuchtkraft der Farben an. Sie können z. B. Farben aufhellen, die mit der Zeit verblasst sind.
Hinweis Der natürliche Farbton des Originalbilds geht ggf. verloren, wenn Sie die Sättigung zu stark erhöhen. Farbbalance Passen Sie Bilder mit Farbstich an. Ein "Farbstich" entsteht, wenn eine Farbe aufgrund der Wetterverhältnisse bei der Aufnahme oder aufgrund starker Umgebungsfarben ein Bild dominiert. Bewegen Sie (Regler) unter Farbbalance (Color Balance) nach links bzw. nach rechts, um die entsprechende Farbe hervorzuheben.
Helligkeit und Kontrast anpassen Klicken Sie auf der Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear (Scanner-Treiber) auf (Helligkeit/Kontrast). Hinweis Klicken Sie auf (Abwärtspfeil), um zur Detailansicht zu wechseln. Klicken Sie auf (Aufwärtspfeil), um zur vorherigen Ansicht zurückzukehren. Klicken Sie auf Standard (Defaults), um alle Anpassungen im aktuellen Fenster rückgängig zu machen.
Passen Sie den Grünkanal an. • Blau (Blue) Passen Sie den Blaukanal an. Hinweis Es wird nur Graustufen (Grayscale) unter Farbkanal (Channel) angezeigt, wenn für Farbmodus (Color Mode) die Option Graustufen (Grayscale) ausgewählt wurde. Helligkeit Passen Sie die Bildhelligkeit an. Verschieben Sie (Regler) unter Helligkeit (Brightness) nach links, um ein dunkleres Bild zu erhalten, und nach rechts, um ein helleres Bild zu erhalten. Sie können auch einen Wert eingeben (-127 bis 127).
Kontrast verringert Originalbild Kontrast erhöht Hinweis Durch das Erhöhen des Kontrasts kann weichen Bildern ein dreidimensionales Aussehen verliehen werden. Wenn Sie den Kontrast zu stark erhöhen, können jedoch Schatten und Spitzlichter verloren gehen.
Histogramm anpassen Klicken Sie auf der Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear (Scanner-Treiber) auf (Histogramm). Hinweis Klicken Sie auf Standard (Defaults), um alle Anpassungen im aktuellen Fenster rückgängig zu machen. Kanal Jeder einzelne Bildpunkt setzt sich in verschiedenen Anteilen aus den Farben Rot, Grün und Blau zusammen (Farbverlauf). Diese Farben können individuell als "Kanal" angepasst werden. • Hauptkanal (Master) Passen Sie Rot, Grün und Blau an.
Histogramme lesen Sie können das Histogramm eines bestimmten Bereichs für jeden Farbkanal (Channel) anzeigen. Je höher die Spitze im Histogramm ist, desto mehr Daten sind auf die betreffende Stufe verteilt. (1) Heller Bereich (2) Dunkler Bereich (3) Gesamtbild Es sind mehr Daten auf den Es sind mehr Daten auf den Die Daten sind weit zwischen Spitzlichtbereich verteilt. Schattenbereich verteilt. dem Spitzlichter- und dem Schattenbereich verteilt.
Bilder, bei denen mehr Daten auf den Spitzlichtbereich verteilt sind Verschieben Sie den Schwarzpunkt-Regler in Richtung des Spitzlichtbereichs. Bilder, bei denen mehr Daten auf den Schattenbereich verteilt sind Verschieben Sie den Weißpunkt-Regler in Richtung des Schattenbereichs. Bilder, bei denen die Daten weit verteilt sind Verschieben Sie den Schwarzpunkt-Regler in Richtung des Spitzlichtbereichs und den Weißpunkt-Regler in Richtung des Schattenbereichs.
Histogramme anpassen (mithilfe der Pipettenwerkzeuge) Wenn Sie einen Farbkanal (Channel) auswählen und auf die Schwarzpunkt-, Mittelpunktoder Weißpunkt-Pipette klicken, wird der Mauszeiger auf dem Vorschaubild als Pipette angezeigt. Klicken Sie auf eine der unter dem Histogramm angezeigten Pipetten, um die entsprechende Einstellung zu ändern. - Der Punkt, auf den Sie mit (Schwarzpunkt-Pipette) klicken, wird als dunkelster Punkt festgelegt. Sie können auch einen Wert eingeben (0 bis 245).
Farbtonkurve anpassen Klicken Sie auf der Registerkarte Erweiterter Modus (Advanced Mode) von ScanGear (Scanner-Treiber) auf (Farbtonkurve - Einstellungen). Hinweis Klicken Sie auf Standard (Defaults), um alle Anpassungen im aktuellen Fenster rückgängig zu machen. Kanal Jeder einzelne Bildpunkt setzt sich in verschiedenen Anteilen aus den Farben Rot, Grün und Blau zusammen (Farbverlauf). Diese Farben können individuell als "Kanal" angepasst werden. • Hauptkanal (Master) Passen Sie Rot, Grün und Blau an.
Farbtonkurven lesen Bei ScanGear ist das Scannen von Bildern mit einem Scanner die Eingabe und die Anzeige auf einem Monitor die Ausgabe. Die "Farbtonkurve" zeigt für jeden Farbkanal (Channel) die Balance zwischen Farbtoneingabe und -ausgabe an.
Starker Kontrast (High contrast) (S-Kurve) Die Spitzlichter und die Schatten der Eingabeseite werden erhöht, wodurch ein Bild mit hohem Kontrast entsteht. Negativ-/Positiv-Bild umkehren (Reverse the negative/positive image) (absteigende Linie) Die Eingabe- und Ausgabeseite werden vertauscht, so dass ein invertiertes Bild entsteht.
Grenzwert einstellen Die Helligkeit von Farb- und Graustufenbildern wird als Wert zwischen 0 und 255 ausgedrückt. Beim Erstellen von Schwarzweißbildern hingegen werden alle Farben dem Wert für Schwarz (0) oder dem Wert für Weiß (255) zugeordnet. "Grenzwert" ist der Wert, der festlegt, ob eine Farbe als Schwarz oder als Weiß angesehen wird. Durch Anpassen des Grenzwerts können Sie eine schärfere Darstellung von Text in Dokumenten erreichen oder ein Durchscheinen bei Zeitungen verhindern.
Bildschirme von ScanGear (Scanner-Treiber) Registerkarte Basismodus Registerkarte Erweiterter Modus Eingabe-Einstellungen Ausgabe-Einstellungen Bildeinstellungen Schaltflächen für die Farbeinstellung Dialogfeld Voreinstellungen Registerkarte Scanner Registerkarte Vorschau Registerkarte Scannen Registerkarte Farbeinstellung 139
Registerkarte Basismodus In diesem Modus können Sie ganz einfach scannen, indem Sie die Anweisungen auf dem Bildschirm befolgen. In diesem Abschnitt werden die auf der Registerkarte Basismodus (Basic Mode) verfügbaren Einstellungen und Funktionen beschrieben. (1) Einstellungen und Bedienschaltflächen (2) Symbolleiste (3) Vorschaubereich Hinweis Je nach Dokumenttyp und Ansicht stehen unterschiedliche Optionen zur Verfügung.
Hinweis Wenn Sie einen Dokumenttyp auswählen, wird die Funktion Scharfzeichnen aktiviert. Die Funktion Bildanpassung, die Bilder basierend auf dem Dokumenttyp anpasst, wird ebenfalls aktiviert. Wenn Sie die Option Zeitschrift (Farbe) (Magazine (Color)) wählen, wird die Funktion Entrastern aktiviert. • Vorschaubild anzeigen (Display Preview Image) • Vorschau (Preview) Führt einen Testscan durch. Hinweis Wenn Sie das Gerät zum ersten Mal verwenden, wird die Scanner-Kalibrierung automatisch gestartet.
Wählen Sie ein Ausgabeformat. Die hier verfügbaren Optionen sind davon abhängig, welche Einstellung unter Ziel (Destination) ausgewählt wurde. • Flexibel (Flexible) Mit dieser Funktion können Sie die Schnittrahmen (Scan-Bereiche) frei anpassen. In Miniaturansicht Ziehen Sie die Maus über eine Miniaturansicht, um einen Schnittrahmen anzuzeigen. Wenn ein Schnittrahmen angezeigt wird, wird der Bildteil innerhalb des Rahmens gescannt. Wenn kein Schnittrahmen angezeigt wird, wird jedes Bild einzeln gescannt.
Im Dialogfeld Ausgabeformat hinzufügen/löschen (Add/Delete the Output Size) können Sie mehrere Ausgabeformate gleichzeitig angeben und speichern. Die gespeicherten Elemente werden in der Liste Ausgabeformat (Output Size) registriert und zusammen mit den vordefinierten Elementen zur Auswahl angezeigt. Hinzufügen Geben Sie Ausgabeformatname (Output Size Name), Breite (Width) und Höhe (Height) an, um ein Format hinzuzufügen, und klicken Sie anschließend auf Hinzufügen (Add).
• Schnittrahmen anpassen (Adjust cropping frames) Sie können den Scan-Bereich im Vorschaubereich anpassen. Wenn kein Bereich festgelegt wurde, wird das Dokument in der Dokumentgröße gescannt (Automatisch beschneiden). Wenn ein Bereich festgelegt wurde, wird nur dieser gescannt. Schnittrahmen anpassen (ScanGear) • Bildkorrekturen (Image corrections) Hiermit können Sie Korrekturen auf Bilder anwenden.
Mit dieser Funktion können Sie die Farben des gesamten Bildes anpassen. Sie können Farben korrigieren, die z. B. durch einen Farbstich verblasst sind, und die natürlichen Farben wiederherstellen. Änderungen werden direkt in der Vorschau sichtbar. Farben mithilfe eines Farbmusters anpassen Wichtig Die Einstellung ist nicht verfügbar, wenn Sie Farbabgleich (Color Matching) auf der Registerkarte Farbeinstellung (Color Settings) des Dialogfelds Voreinstellungen (Preferences) auswählen.
• (Nach links drehen) Das Vorschaubild wird um 90 Grad gegen den Uhrzeigersinn gedreht. - Das Ergebnis wird auf das gescannte Bild angewendet. - Das Bild wird wieder in den Ausgangszustand zurückversetzt, wenn Sie es erneut in die Vorschau laden. • (Nach rechts drehen) Das Vorschaubild wird um 90 Grad im Uhrzeigersinn gedreht. - Das Ergebnis wird auf das gescannte Bild angewendet. - Das Bild wird wieder in den Ausgangszustand zurückversetzt, wenn Sie es erneut in die Vorschau laden.
Zeigt die Version von ScanGear und die aktuellen Einstellungen (Dokumenttyp usw.) an. • (Handbuch öffnen) Öffnet diese Seite. (3) Vorschaubereich • Vorschaubereich Hier wird ein Testbild angezeigt, wenn Sie auf Vorschau (Preview) geklickt haben. Sie können auch die Ergebnisse der Einstellungen (Bildkorrekturen, Farbanpassungen usw.) in "(1) Einstellungen und Bedienschaltflächen" überprüfen.
wechseln), um den vorherigen oder nächsten Rahmen anzuzeigen. Doppelklicken Sie erneut auf den Rahmen, um die ursprüngliche Anzeigegröße wiederherzustellen. Wenn in der Symbolleiste (Gesamtbildansicht) angezeigt wird Elemente auf der Auflagefläche werden als ein einziges Bild gescannt und angezeigt. Alle Bereiche in den Schnittrahmen werden gescannt. Hinweis Sie können den Schnittrahmen auf dem angezeigten Bild festlegen. In der Miniaturansicht können Sie nur einen Schnittrahmen pro Bild erstellen.
Registerkarte Erweiterter Modus In diesem Modus können Sie erweiterte Scan-Einstellungen festlegen, z. B. den Farbmodus, die Ausgabeauflösung, die Helligkeit und den Farbton. In diesem Abschnitt werden die auf der Registerkarte Erweiterter Modus (Advanced Mode) verfügbaren Einstellungen und Funktionen beschrieben. (1) Einstellungen und Bedienschaltflächen (2) Symbolleiste (3) Vorschaubereich Hinweis Je nach Dokumenttyp und Ansicht stehen unterschiedliche Optionen zur Verfügung.
Geben Sie einen Wert unter Einstellungsname (Setting Name) ein, und klicken Sie auf Hinzufügen (Add). Der Name wird unter Liste bevorzugter Einstellungen (Favorite Settings List) angezeigt. Wenn Sie auf Speichern (Save) klicken, wird das Element zusammen mit den vordefinierten Elementen in der Liste Bevorzugte Einstellungen (Favorite Settings) angezeigt und kann ausgewählt werden.
Rückgängig (Undo). Klicken Sie auf Rückgängig (Undo), um die ursprüngliche Anzeigegröße wiederherzustellen. In Miniaturansicht Wenn in der Miniaturansicht mehrere Bilder angezeigt werden, können Sie mit dieser Schaltfläche die Auswahl vergrößern. Klicken Sie am unteren Rand des Bildschirms auf (Rahmen wechseln), um den vorherigen oder nächsten Rahmen anzuzeigen. Hinweis Sie können ein Bild auch vergrößern, indem Sie darauf doppelklicken.
• Scannen (Scan) Startet den Scan-Vorgang. Hinweis Der Fortschritt des Scan-Vorgangs wird angezeigt. Klicken Sie auf Abbrechen (Cancel), um den Scan-Vorgang abzubrechen. Wenn der Scan-Vorgang beendet wurde, wird möglicherweise ein Dialogfeld angezeigt, in dem Sie die nächste auszuführende Aktion auswählen können. Befolgen Sie die Anweisungen, um den Vorgang abzuschließen.
Löscht das Vorschaubild aus dem Vorschaubereich. Durch Klicken auf diese Schaltfläche werden auch die Symbolleisten- und Farbeinstellungen zurückgesetzt. • (Beschneiden) Hiermit können Sie den Scan-Bereich durch Ziehen der Maus festlegen. • (Bild verschieben) Ermöglicht das Ziehen des Bilds mit der Maustaste, bis der gewünschte Bereich angezeigt wird, wenn ein im Vorschaubereich vergrößertes Bild nicht auf den Bildschirm passt. Sie können das Bild auch mithilfe der Bildlaufleisten verschieben.
• (Alle Bilder auswählen) Ist verfügbar, wenn mindestens zwei Bilder angezeigt werden. Wählt die Bilder in der Miniaturansicht aus und versieht sie mit einer blauen Umrandung. • (Alle Schnittrahmen auswählen) Ist verfügbar, wenn mindestens zwei Schnittrahmen festgelegt sind. Ändert die Schnittrahmen in dicke, gestrichelte Linien und wendet die Einstellungen auf alle Schnittrahmen an. • (Schnittrahmen entfernen) Entfernt den ausgewählten Schnittrahmen.
Hinweis Wenn mehrere Bilder in der Vorschau angezeigt werden, signalisieren unterschiedliche Umrisse einen unterschiedlichen Auswahlstatus. Aktiver Rahmen (dicker blauer Umriss): Die angezeigten Einstellungen werden übernommen. Ausgewählter Rahmen (dünner blauer Umriss): Die Einstellungen werden gleichzeitig auf den aktiven und die ausgewählten Rahmen angewendet. Sie können mehrere Bilder auswählen, indem Sie darauf klicken und dabei die StrgTaste gedrückt halten.
Hinweis Sie können den Schnittrahmen auf dem angezeigten Bild festlegen. In der Miniaturansicht können Sie nur einen Schnittrahmen pro Bild erstellen. In der Gesamtbildansicht können mehrere Schnittrahmen erstellt werden.
Eingabe-Einstellungen Unter Eingabe-Einstellungen (Input Settings) können Sie die folgenden Optionen einrichten: • Quelle wählen (Select Source) Der Typ des zu scannenden Dokuments wird angezeigt. • Papierformat (Paper Size) Wählen Sie die Größe des zu scannenden Dokuments aus. Diese Einstellung ist nur in der Gesamtbildansicht verfügbar. Wenn Sie ein Format auswählen, wird die Größe des Vorschaubereichs entsprechend angepasst.
Wählen Sie aus, wie das Dokument gescannt werden soll. • Farbe (Color) Wählen Sie diesen Modus, um Farbdokumente zu scannen oder Farbbilder zu erstellen. In diesem Modus wird das Bild mit 256 Stufen (8 Bit) der Farben R(ot), G(rün) und B(lau) angezeigt. • Graustufen (Grayscale) Wählen Sie diesen Modus, um Schwarzweißfotos zu scannen oder Schwarzweißbilder zu erstellen. In diesem Modus wird das Bild mit 256 Graustufen (d. h. mit 8 Bit Farbtiefe) angezeigt.
Beim automatischen Beschneiden in der Gesamtbildansicht wird das Seitenverhältnis nicht beibehalten, da die Größe eine höhere Priorität hat. Unter "Schnittrahmen anpassen (ScanGear)" finden Sie weitere Informationen zu Schnittrahmen.
Ausgabe-Einstellungen Unter Ausgabe-Einstellungen (Output Settings) können Sie die folgenden Optionen einrichten: • Ausgabeauflösung (Output Resolution) Wählen Sie die Auflösung, mit der gescannt werden soll. Je höher der Wert für die Auflösung, desto detailreicher ist das Bild. Wählen Sie aus den nach dem Klicken auf die Schaltfläche angezeigten Optionen eine Auflösung aus oder geben Sie einen Wert zwischen 25 und 19200 dpi (in 1-dpi-Schritten) an.
In Miniaturansicht Ziehen Sie die Maus über eine Miniaturansicht, um einen Schnittrahmen anzuzeigen. Wenn ein Schnittrahmen angezeigt wird, wird der Bildteil innerhalb des Rahmens gescannt. Wenn kein Schnittrahmen angezeigt wird, wird jedes Bild einzeln gescannt. In Gesamtbildansicht Wird kein Schnittrahmen angezeigt, wird der gesamte Vorschaubereich gescannt. Wenn ein Schnittrahmen angezeigt wird, wird der Bildteil innerhalb des Rahmens gescannt.
Hinzufügen Wählen Sie zum Hinzufügen eines Formats die Option Drucken (Print) oder Bildanzeige (Image display) als Ziel (Destination). Geben Sie anschließend Ausgabeformatname (Output Size Name), Breite (Width) und Höhe (Height) ein und klicken Sie auf Hinzufügen (Add). Für Einheit (Unit) können Sie Inch (inches) oder mm auswählen, wenn für Ziel (Destination) die Option Drucken (Print) ausgewählt wurde.
Beim Scannen mit den aktuellen Einstellungen wird die Datengröße angezeigt. Hinweis Wenn die Datengröße einen bestimmten Wert überschreitet, wird der Wert rot dargestellt. In diesem Fall erscheint eine Warnmeldung, wenn Sie auf Scannen (Scan) klicken. Es empfiehlt sich, die Einstellungen anzupassen, um die Datengröße (Data Size) zu verringern. Scannen Sie anschließend in der Gesamtbildansicht.
Bildeinstellungen Wichtig Wenden Sie diese Funktionen nicht auf Bilder ohne Moiré-Effekte, Staub, Kratzer oder verblasste Farben an. Dies könnte sich ungünstig auf den Farbton auswirken. Die Ergebnisse der Bildkorrektur werden möglicherweise nicht im Vorschaubild angezeigt. Hinweis Welche Einstellungen ausgewählt werden können, hängt von den Einstellungen unter Farbmodus (Color Mode) ab. Das Scannen dauert möglicherweise länger als gewöhnlich, wenn Sie Bildeinstellungen (Image Settings) verwenden.
Die Bildanpassung wird beim automatischen Erkennen des Dokumenttyps angewendet. Es wird empfohlen, diese Einstellung grundsätzlich zu verwenden. • Foto (Photo) Die für Fotos geeigneten Bildanpassungen werden vorgenommen. • Zeitschrift (Magazine) Die für Zeitschriften geeigneten Bildanpassungen werden vorgenommen. • Dokument (Document) Die für Textdokumente geeigneten Bildanpassungen werden vorgenommen. Wichtig Sie können die Bildanpassung (Image Adjustment) nach der Vorschau festlegen.
• Scharfzeichnen (Unsharp Mask) Verstärkt die Konturen der Motive, um die Bildschärfe beim Scannen von Fotos zu erhöhen. • AUS (OFF) Scharfzeichnen wird nicht angewendet. • EIN (ON) Verstärkt die Konturen der Motive, um die Bildschärfe zu erhöhen. Es wird empfohlen, diese Einstellung grundsätzlich zu verwenden. • Entrastern (Descreen) Gedruckte Fotos und Bilder werden durch eine Ansammlung feiner Punkte wiedergegeben.
Wählen Sie diese Option, um kleine und große Staubpartikel und Kratzer zu reduzieren. Dieser Vorgang kann jedoch selbst Spuren im Bild hinterlassen und feinere Bilddetails unkenntlich machen. Wichtig Diese Funktion ist bei bestimmten Fotos möglicherweise nicht wirksam. Hinweis Es wird empfohlen, diese Funktion beim Scannen von gedruckten Materialien auf Ohne (None) zu setzen.
Die Körnigkeit wird nicht reduziert. • Niedrig (Low) Wählen Sie diese Option, wenn das Foto leicht körnig ist. • Mittel (Medium) Es wird empfohlen, diese Einstellung grundsätzlich zu verwenden. • Hoch (High) Wählen Sie diese Option, wenn das Foto sehr körnig ist. Diese Option kann Auswirkungen auf die Kontrast und Schärfe des Bildes haben. Wichtig Die Korrektur wird möglicherweise nicht ordnungsgemäß angewendet, wenn der Scan-Bereich zu klein ist.
Richten Sie das Dokument am Rand der Auflagefläche aus. Andernfalls kann der Schatten nicht vollständig entfernt werden. Schatten können je nach Dokument möglicherweise nicht vollständig entfernt werden. Wenn der Seitenhintergrund nicht weiß ist, werden Schatten möglicherweise nicht korrekt oder gar nicht erkannt. Drücken Sie den Buchrücken während des Scan-Vorgangs wie beim VorschauScannen fest nach unten. Wenn die Bindung nicht flach aufliegt, kann der Schatten nicht vollständig entfernt werden.
Schaltflächen für die Farbeinstellung Die Schaltflächen für die Farbeinstellung können für Feinkorrekturen an der Bildhelligkeit und den Farbtönen verwendet werden. Hiermit können Sie die Helligkeit oder den Kontrast des Bilds, seine hellste und dunkelste Stufe (Histogramm) und die Balance (Farbtonkurve) anpassen.
Sättigung und Farbbalance anpassen • (Helligkeit/Kontrast) Mit dieser Funktion können Sie die Helligkeit und den Kontrast des Bilds anpassen. Wenn das Bild zu dunkel oder zu hell ist oder wenn die Bildqualität unter zu schwachem Kontrast leidet, können Sie die Helligkeit und den Kontrast verändern. Helligkeit und Kontrast anpassen • (Histogramm) In einem Histogramm wird die Datenkonzentration auf den einzelnen Helligkeitspegeln eines Bilds dargestellt.
• Wenn Sie den Cursor auf eine Stelle im Vorschaubild setzen, wird der Bildbereich vergrößert, und die RGB-Werte vor und nach der Farbanpassung werden für diese Stelle angezeigt. (Wenn für Farbmodus (Color Mode) die Option Graustufen (Grayscale) ausgewählt ist, wird nur L angezeigt.) • (Grenzwert) Legen Sie die Grenze (den Grenzwert) für das Aufteilen der Farben in Schwarz und Weiß fest.
Sie können die gespeicherten Farbtonkurven- und Grenzwerteinstellungen laden und auf ein Vorschaubild anwenden. Wenn Sie die Einstellungen laden möchten, wählen Sie den gespeicherten Namen aus dem Pull-Down-Menü aus. Hinweis Sie können bis zu 20 Elemente speichern. • Standard (Defaults) Setzen Sie alle Anpassungen (Sättigung/Farbbalance, Helligkeit/Kontrast, Histogramm und Farbtonkurve) zurück.
Dialogfeld Voreinstellungen Klicken Sie in ScanGear (Scanner-Treiber) auf Voreinstellungen... (Preferences...), um das Dialogfeld Voreinstellungen (Preferences) zu öffnen. Im Dialogfeld Voreinstellungen (Preferences) können Sie erweiterte Einstellungen für ScanGear-Funktionen über die Registerkarten Scanner, Vorschau (Preview), Scannen (Scan) und Farbeinstellung (Color Settings) festlegen.
Registerkarte Scanner In der Registerkarte Scanner können Sie die folgenden Einstellungen festlegen. • Autom. Ein/Aus-Einstellungen (Auto Power Settings) Sie können festlegen, dass sich das Gerät automatisch ein- oder ausschaltet. Klicken Sie auf Einstellungen... (Settings...), um das Dialogfeld Autom. Ein/AusEinstellungen (Auto Power Settings) anzuzeigen.
Wählen Sie den gewünschten Zeitraum aus der Liste aus. Wenn dieser Zeitraum verstreicht, ohne dass Daten empfangen werden, schaltet sich das Gerät automatisch aus. • Geräuscharme Einstellungen (Quiet Settings) Die geräuscharme Funktion senkt den Geräuschpegel dieses Geräts beim Drucken. Verwenden Sie diese Funktion, um die Betriebsgeräusche zu reduzieren, z. B. wenn Sie nachts scannen oder drucken. Klicken Sie auf Einstellungen... (Settings...), um den geräuscharmen Modus festzulegen.
Wichtig Die Zeitangaben für Startzeit (Start time) und Ende (End time) müssen unterschiedlich sein. Wenn Sie Zeitangaben vorgenommen haben, wird der geräuscharme Modus nicht auf Vorgänge anwendet, die direkt über das Gerät ausgeführt werden (Kopieren, Direktdruck usw.). • Speicherordner für temporäre Dateien wählen (Select Folder Where Temporary Files are Saved) Zeigt den Ordner an, in dem Bilder temporär gespeichert werden sollen. Klicken Sie auf Durchsuchen... (Browse...
Registerkarte Vorschau In der Registerkarte Vorschau (Preview) können Sie die folgenden Einstellungen festlegen. • Vorschau beim Start von ScanGear (Preview at Start of ScanGear) Wählen Sie eine Option für die Bildvorschau beim Start von ScanGear (Scanner-Treiber). • Vorschau automatisch ausführen (Automatically Execute Preview) Die Vorschau wird beim Start von ScanGear automatisch angezeigt.
Der Schnittrahmen (Scan-Bereich) wird nach der Vorschau automatisch entsprechend der Dokumentgröße angezeigt. • Letzten Beschneiderahmen bei Vorschaubildern anzeigen (Display the Last Frame on Previewed Images) Nach der Vorschau wird ein Schnittrahmen angezeigt, der dieselbe Größe besitzt wie der zuletzt verwendete Schnittrahmen. • Ohne (None) Nach der Vorschau wird kein Schnittrahmen angezeigt.
Registerkarte Scannen In der Registerkarte Scannen (Scan) können Sie die folgenden Einstellungen festlegen. • Status des ScanGear-Dialogfelds nach dem Scannen (Status of ScanGear dialog after scanning) Geben Sie an, was Sie nach dem Scannen von Bildern mit ScanGear (Scanner-Treiber) tun möchten. • ScanGear automatisch schließen (Close ScanGear automatically) Mit dieser Einstellung kehren Sie zur Originalanwendung zurück, nachdem der ScanVorgang abgeschlossen ist.
Hinweis Auch wenn die Option ScanGear nicht automatisch schließen (Do not close ScanGear automatically) oder Dialogfeld für Auswahl der nächsten Aktion anzeigen (Display the dialog to select next action) ausgewählt ist, kann es vorkommen, dass sie nicht von allen Anwendungen unterstützt wird.
Registerkarte Farbeinstellung In der Registerkarte Farbeinstellung (Color Settings) können Sie die folgenden Einstellungen festlegen. • Farbeinstellung Wählen Sie eine der folgenden Optionen. Sie können eine Option auswählen, wenn Farbmodus (Color Mode) auf Farbe (Color) oder Graustufen (Grayscale) eingestellt ist. • Empfohlen (Recommended) Wählen Sie diese Option, wenn ein Dokument auf dem Bildschirm mit kräftigen Farbtönen wiedergeben werden soll.
• Ohne (None) Wählen Sie diese Funktion, um die Farbkorrekturfunktion von ScanGear (ScannerTreiber) zu deaktivieren. Hinweis Der Farbabgleich kann vorgenommen werden, wenn ScanGear, der Bildschirm, ein Farbmanagement-kompatibles Programm (z. B. Adobe Photoshop) und der Drucker richtig eingerichtet sind. Die Einstellungen für den Bildschirm, den Drucker und das Programm finden Sie in den entsprechenden Handbüchern.
Objekte platzieren (beim Scannen über den Computer) Im Folgenden wird beschrieben, wie Objekte auf die Auflagefläche des Scanners oder Druckers zu legen sind. Platzieren Sie die zu scannenden Objekte entsprechend ihrem Typ ordnungsgemäß auf der Auflagefläche. Anderenfalls werden sie möglicherweise nicht richtig gescannt. Wichtig Legen Sie keine Gegenstände auf dem Vorlagendeckel ab. Beim Öffnen des Vorlagendeckels können die Objekte in den Scanner oder Drucker fallen und eine Fehlfunktion verursachen.
schraffierten Bereich befinden, werden nicht gescannt. Wichtig Informationen zu den Objektteilen, die nicht gescannt werden können, finden Sie auf der Startseite vom Online-Handbuch im Abschnitt "Auflegen von Originalen" des entsprechenden Modells. Wichtig Große Objekte (z. B. Fotos im Format A4), die nicht mit einem Abstand zum Rand/Pfeil (Ausrichtungsmarkierung) der Auflagefläche platziert werden können, werden möglicherweise als PDF-Datei gespeichert.
Hinweis Sie können bis zu 12 Objekte positionieren. Die Ausrichtung schräg liegender Objekte (maximal 10 Grad) wird automatisch korrigiert.
Schnittrahmen anpassen (ScanGear) Beim "Zuschneiden" wählen Sie den Bildbereich aus, den Sie beibehalten möchten. Die übrigen Bildbereiche werden beim Scannen verworfen. Sie können auf den Registerkarten Basismodus (Basic Mode) und Erweiterter Modus (Advanced Mode) Schnittrahmen (Scan-Bereiche) auf dem im Vorschaubereich des Bildschirms angezeigten Bild festlegen. Beim Sannen wird jeder Bereich in einem Schnittrahmen als separates Bild gescannt.
(1) Dicker Schnittrahmen (umlaufend oder fest) Stellt einen ausgewählten Schnittrahmen dar. Wird nur in der Gesamtbildansicht angezeigt. Sie können mehrere Schnittrahmen auswählen, indem Sie auf sie klicken und dabei die Taste Strg gedrückt halten. Ausgabeformat, Bildkorrekturen und andere Einstellungen auf der Registerkarte Basismodus (Basic Mode) oder Erweiterter Modus (Advanced Mode) werden auf alle ausgewählten Schnittrahmen angewendet.
Sie können einen Schnittrahmen um 90 Grad drehen, indem Sie auf (Seitenverhältnis wechseln) klicken. Die Schaltfläche (Seitenverhältnis wechseln) ist jedoch nicht verfügbar, wenn als Ausgabeformat (Output Size) die Option Flexibel (Flexible) ausgewählt wurde. Mehrere Schnittrahmen erstellen In Miniaturansicht Pro Bild kann nur ein Schnittrahmen erstellt werden.
Wenn Sie mehrere Schnittrahmen auswählen und die Einstellungen auf der Registerkarte auf der rechten Seite von ScanGear ändern, werden die Einstellungen auf alle ausgewählten Schnittrahmen angewendet. Wenn Sie einen neuen Schnittrahmen erstellen, übernimmt dieser die Einstellungen des zuletzt ausgewählten Schnittrahmens. Hinweis Sie können bis zu 12 Schnittrahmen erstellen. Der Scan-Vorgang dauert länger als gewöhnlich, wenn mehrere Schnittrahmen ausgewählt wurden.
Allgemeine Hinweise (Scanner-Treiber) ScanGear (Scanner-Treiber) unterliegt folgenden Einschränkungen. Berücksichtigen Sie diese bei der Verwendung. Scanner-Treiber-Einschränkungen • Bei Verwendung des NTFS-Dateisystems wird die TWAIN-Datenquelle möglicherweise nicht aufgerufen. Der Grund dafür ist, dass das TWAIN-Modul aus Sicherheitsgründen nicht in den Ordner "winnt" geschrieben werden kann. Wenn Sie Hilfe benötigen, setzen Sie sich mit dem Administrator des Computers in Verbindung.
• ScanGear und der WIA-Treiber können nicht gleichzeitig verwendet werden. • Schalten Sie den Computer während des Scan-Vorgangs nicht in den Standby-Modus. Anwendungen mit Verwendungseinschränkungen • Wenn Sie das in Windows XP Media Center Edition 2005 enthaltene Media Center starten, können Sie möglicherweise nicht über das Bedienfeld des Geräts scannen. Starten Sie den Computer in diesem Fall neu.
Hilfreiche Informationen über das Scannen Anpassen von Schnittrahmen im Fenster Bild zusammenfügen Auflösung Datenformate Farbabgleich 193
Anpassen von Schnittrahmen im Fenster Bild zusammenfügen Beim "Zuschneiden" wählen Sie den Bildbereich aus, den Sie beibehalten möchten. Die übrigen Bildbereiche werden beim Scannen verworfen. Im Fenster Bild zusammenfügen (Image Stitch) können Sie einen Schnittrahmen auf dem im Vorschaubereich angezeigten Bild festlegen.
Schnittrahmen löschen Zum Löschen des Schnittrahmens deaktivieren Sie das Kontrollkästchen Schnittrahmen anpassen (Adjust cropping frames).
Auflösung Bei den gescannten Bilddaten handelt es sich um eine Ansammlung von Punkten, die Daten zur Helligkeit und Farbe der Darstellung enthalten. Die Dichte dieser Punkte wird "Auflösung" genannt. Die Auflösung bestimmt, wie viele Detailinformationen in Ihrem Bild enthalten sind. Die Einheit für die Auflösung ist dpi (dots per inch, Punkte pro Zoll). Bei dpi handelt es sich um die Anzahl der Punkte pro Zoll (2,5 cm). Je höher der Auflösungswert, desto detailreicher wird das Bild.
Textdokument (Dokument Kopieren oder Zeitschrift) Farbe, Graustufen oder Schwarzweiß 300 dpi An E-Mail anhängen Farbe, Graustufen oder Schwarzweiß 150 dpi Text mit OCR scannen Farbe oder Graustufen 300 dpi Wichtig Wenn Sie die Auflösung verdoppeln, vervierfacht sich die Datengröße des gescannten Bilds. Wenn die Datei zu groß ist, sinkt die Verarbeitungsgeschwindigkeit deutlich und es kann zu Beeinträchtigungen kommen, z. B. aufgrund von Speichermangel.
Datenformate Sie können beim Speichern von gescannten Bildern ein Datenformat auswählen. Welches Datenformat Sie auswählen sollten, hängt davon ab, wie und mit welcher Anwendung Sie das Bild verwenden möchten. Je nach Anwendung und Betriebssystem (Windows oder Mac OS) stehen unterschiedliche Datenformate zur Verfügung. Nachfolgend finden Sie Informationen zu den verschiedenen Bilddatenformaten. PNG (Standard-Dateierweiterung: .png) Dieses Datenformat wird häufig auf Websites verwendet.
Es kann auf verschiedenen Computern und Betriebssystemen verwendet werden. Außerdem ist das Einbetten von Schriftarten möglich. Daher können Benutzer in unterschiedlichen Umgebungen diese Dateien ungeachtet der Unterschiede ganz einfach austauschen.
Farbabgleich Beim "Farbabgleich" werden Anpassungen vorgenommen, damit die Farbtöne des Originals mit denen der Bildschirmanzeige und denen des Farbdrucks übereinstimmen. Die Farbtöne werden auf Ihrem Scanner oder Drucker wie unten dargestellt angepasst.
Menü und Einstellungsfenster von IJ Network Scanner Selector EX Mit dem IJ Network Scanner Selector EX können Scanner oder Drucker ausgewählt werden, um über ein Netzwerk vom Computer oder mit dem Bedienfeld zu scannen oder zu drucken. Nach der Installation wird IJ Network Scanner Selector EX im Benachrichtigungsbereich auf dem Desktop angezeigt.
Wichtig Wenn Sie ein Modell verwenden, bei dem das Scannen mithilfe des Bedienfelds innerhalb eines Netzwerks nicht möglich ist, kann mit dem Bedienfeld auch dann nicht gescannt werden, wenn diese Einstellung aktiviert ist. • Einstellungen... (Settings...) Der Bildschirm mit den Einstellungen "Scannen von PC" wird angezeigt. Sie können das zu verwendende Modell auswählen. • Info (About) Zeigt die Versionsinformationen an. • Beenden (Exit) (Aktiviert) oder Beendet IJ Network Scanner Selector EX.
Wichtig Wenn Sie ein Modell verwenden, bei dem das Scannen mithilfe des Bedienfelds innerhalb eines Netzwerks nicht möglich ist, wird dieses Modell im Scanner (Scanners) nicht angezeigt, und die Einstellung ist nicht verfügbar. Bildschirm mit den Einstellungen "Scannen von Bedienfeld" Klicken Sie im Bildschirm mit den Einstellungen "Scannen von PC" auf Einstellungen "Scannen von Bedienfeld" (Scan-from-Operation-Panel Settings), um den Bildschirm mit den Einstellungen "Scannen von Bedienfeld" anzuzeigen.
„Deinstallieren von IJ Network Scanner Selector EX“. Sie können über USB scannen, selbst wenn das Programm nicht entfernt wurde.
Deinstallieren von IJ Network Scanner Selector EX Führen Sie die unten angegebenen Schritte aus, um IJ Network Scanner Selector EX vom Computer zu deinstallieren. Wichtig Nach der Deinstallation von IJ Network Scanner Selector EX kann innerhalb eines Netzwerks nicht gescannt werden. Melden Sie sich mit Administratorrechten am Benutzerkonto an. 1. Deinstallieren Sie IJ Network Scanner Selector EX. • Windows 8: 1.
2. Wählen Sie in der Programmliste die Option Canon IJ Network Scanner Selector EX aus, und klicken Sie anschließend auf Ändern/Entfernen (Change/Remove). 2. Klicken Sie bei Anzeige der Bestätigungsmeldung auf Ja (Yes). 3. Wenn die Deinstallation abgeschlossen ist, klicken Sie auf OK. Hinweis Wenn eine Aufforderung zum Neustarten des Computers angezeigt wird, klicken Sie auf OK, um den Computer neu zu starten.
Weitere Scan-Methoden Scannen mit WIA-Treiber Scannen über die Systemsteuerung (nur Windows XP) 207
Scannen mit WIA-Treiber Sie können ein Objekt aus einer WIA-kompatiblen (Windows Image Acquisition) Anwendung heraus scannen. WIA ist ein Treibermodell in Windows XP und neueren Betriebssystemversionen. Es ermöglicht Ihnen das Scannen von Objekten ohne die Verwendung einer Anwendung. Das Verfahren ist von der jeweiligen Anwendung abhängig. Folgende Verfahren dienen nur als Beispiele. Weitere Informationen hierzu finden Sie im Handbuch der Anwendung.
Hinweis Wenn Sie mehrere Scanner oder Drucker besitzen, wird möglicherweise ein Bildschirm zur Auswahl des Scanners angezeigt. Doppelklicken Sie auf den zu verwendenden Scanner. Für eine USB-Verbindung: Canon XXX series (wobei "XXX" für den Modellnamen steht) Für eine Netzwerkverbindung: XXX series_MAC-Adresse (XXX series_MAC address) (wobei "XXX" für den Modellnamen steht) 3. Legen Sie die Einstellungen fest. • Scanner (Scanners) Der Name des gegenwärtig eingestellten Produkts wird angezeigt.
• Helligkeit (Brightness) Stellen Sie die Helligkeit durch Verschieben des Reglers ein. Verschieben Sie ihn nach links, um ein dunkleres Bild zu erhalten, und nach rechts, um ein helleres Bild zu erhalten. Sie können auch einen Wert eingeben (-100 bis 100). • Kontrast (Contrast) Stellen Sie den Kontrast durch Verschieben des Reglers ein. Wenn Sie ihn nach links verschieben, wird der Bildkontrast verringert und das Bild erscheint weicher.
3. Wählen Sie den Bildtyp gemäß dem Typ des zu scannenden Objekts aus. Es stehen folgende Auswahlmöglichkeiten zur Verfügung: Farbbild (Color picture), Graustufenbild (Grayscale picture), Schwarzweißfoto oder Text (Black and white picture or text) und Benutzerdefinierte Einstellungen (Custom Settings). Hinweis Wenn Sie den Scanner oder Drucker mit einer Netzwerkverbindung verwenden, unterscheiden sich die Optionen für den Bildtyp möglicherweise von den bei einer USB-Verbindung verfügbaren Optionen.
• Zurücksetzen (Reset) Klicken Sie auf diese Schaltfläche, um die ursprünglichen Einstellungen wiederherzustellen. Wichtig Wenn Sie den Scanner oder Drucker mit einer Netzwerkverbindung verwenden, können Sie keine Helligkeit (Brightness) und keinen Kontrast (Contrast) festlegen. 5. Klicken Sie auf Vorschau (Preview), um sich das Bild in der Vorschau anzusehen. Das Vorschaubild wird auf der rechten Seite angezeigt. Ziehen Sie das Symbol zum Festlegen des Scan-Bereichs. 6. Klicken Sie auf Scannen (Scan).
Scannen über die Systemsteuerung (nur Windows XP) Sie können Bilder unter Verwendung des WIA-Treibers über die Systemsteuerung von Windows XP scannen. Wichtig Wenn Sie den Scanner oder Drucker mit einer Netzwerkverbindung verwenden, können Sie nicht mithilfe des WIA-Treibers scannen. 1. Wählen Sie im Menü Start die Option Systemsteuerung (Control Panel). 2.
5. Klicken Sie auf Benutzerdefinierte Einstellungen (Custom settings) und legen Sie die Voreinstellungen wie erforderlich fest. • Helligkeit (Brightness) Stellen Sie die Helligkeit durch Verschieben des Reglers ein. Verschieben Sie ihn nach links, um ein dunkleres Bild zu erhalten, und nach rechts, um ein helleres Bild zu erhalten. Sie können auch einen Wert eingeben (-127 bis 127). • Kontrast (Contrast) Stellen Sie den Kontrast durch Verschieben des Reglers ein.
Objekte platzieren (beim Scannen über den Computer) Im Folgenden wird beschrieben, wie Objekte auf die Auflagefläche des Scanners oder Druckers zu legen sind. Platzieren Sie die zu scannenden Objekte entsprechend ihrem Typ ordnungsgemäß auf der Auflagefläche. Anderenfalls werden sie möglicherweise nicht richtig gescannt. Wichtig Legen Sie keine Gegenstände auf dem Vorlagendeckel ab. Beim Öffnen des Vorlagendeckels können die Objekte in den Scanner oder Drucker fallen und eine Fehlfunktion verursachen.
Wichtig Wichtig Große Objekte (z. B. Fotos im Format A4), die nicht mit einem Abstand zum Rand/Pfeil (Ausrichtungsmarkierung) der Auflagefläche platziert werden können, werden möglicherweise als PDF-Datei gespeichert. Wenn das Objekt nicht im PDF-Format gespeichert werden soll, müssen Sie zunächst das gewünschte Datenformat angeben und dann den Scanvorgang starten.
Sie können bis zu vier Objekte auflegen, wenn im Dialogfeld für Einstellungen in IJ Scan Utility das Kontrollkästchen Gescannte Bilder beim Übertragen komprimieren (Compress scanned images upon transfer) aktiviert ist. Die Ausrichtung schräg liegender Objekte (maximal 10 Grad) wird automatisch korrigiert.
Scannen über das Bedienfeld des Geräts Weiterleiten gescannter Daten auf den Computer mithilfe des Bedienfelds am Gerät Grundlagen Anhängen der gescannten Daten an eine E-Mail über das Bedienfeld am Gerät Speichern von gescannten Daten auf der Speicherkarte mithilfe des Bedienfelds am Gerät Löschen gescannter Daten auf der Speicherkarte Vornehmen von Einstellungen über das Bedienfeld am Gerät Netzwerk-Scan-Einstellungen Mit IJ Scan Utility ein Verhalten für Befehle vom Bedienfeld auswählen 218
Weiterleiten gescannter Daten auf den Computer mithilfe des Bedienfelds am Gerät Sie können mithilfe des Bedienfelds am Gerät die gescannten Daten auf den Computer weiterleiten. Überprüfen Sie vor Weiterleiten gescannter Daten auf den Computer die folgenden Punkte: • Die MP Drivers sind installiert. Falls die MP Drivers noch nicht installiert sind, installieren Sie die MP Drivers von der Installations-CDROM oder unserer Website. • Das Gerät ist ordnungsgemäß an einen Computer angeschlossen.
Bei Weiterleitung der Daten an den Netzwerk-Computer: Der Bildschirm zur Auswahl des Mediums, auf das Sie Daten speichern möchten, wird angezeigt. Hinweis • Wenn der Scan-Standby-Bildschirm zur Weiterleitung der Daten an den über USB angeschlossenen Computer in der LCD-Anzeige angezeigt wird, drücken Sie die linke Taste Funktion (Function), um den Bildschirm zur Auswahl des Speicherorts der Daten anzuzeigen.
Hinweis • Bei Weiterleitung der gescannten Daten über WSD an den Computer können Sie den Dokumenttyp nicht auswählen. Automat. Scannen (Auto scan) Dieses Element ist nur verfügbar, wenn das Gerät über ein USB-Kabel an den Computer angeschlossen ist. Das Gerät erkennt den Typ des Originals automatisch, und das Bild wird mit optimierten Werten für Größe, Auflösung und Datenformat weitergeleitet. Wichtig • Sie können Automat.
5. Legen Sie das Originaldokument auf die Auflagefläche. Hinweis • Den Vorgang zum Auflegen des Originals können Sie mit der mittleren Taste Funktion (Function) bestätigen. 6. Drücken Sie zum Scannen in Farbe die Taste Farbe (Color) bzw. zum Scannen in Schwarzweiß die Taste Schwarz (Black). Hinweis • Wenn Sie die gescannten Daten über WSD an den Computer weiterleiten, drücken Sie die Taste Farbe (Color).
Wenn Sie Originale mit erweiterten Einstellungen scannen möchten oder wenn Sie die gescannten Bilder bearbeiten oder drucken möchten: Wenn Sie Originale über einen Computer mit My Image Garden scannen, können Sie in My Image Garden gescannte Dokumente bearbeiten, z. B. durch Optimieren oder Zuschneiden. Außerdem können Sie gescannte Bilder mit der kompatiblen Anwendungssoftware bearbeiten oder drucken.
Anhängen der gescannten Daten an eine E-Mail über das Bedienfeld am Gerät Sie können gescannte Daten über das Bedienfeld des Geräts an eine E-Mail-Nachricht anhängen. Überprüfen Sie vor dem Anhängen gescannter Daten an eine E-Mail die folgenden Punkte: • Die MP Drivers sind installiert. Falls die MP Drivers noch nicht installiert sind, installieren Sie die MP Drivers von der Installations-CDROM oder unserer Website. • Das Gerät ist ordnungsgemäß an einen Computer angeschlossen.
3. Wählen Sie An E-Mail anhängen. (Attach to E-mail) aus, und drücken Sie dann die Taste OK. 4. Verwenden Sie die Taste , um den PC auszuwählen, an den die gescannten Daten weiterleitet werden sollen, und drücken Sie die Taste OK. Wählen Sie bei einem über USB angeschlossenen Computer die Option Lokal (USB) (Local (USB)) aus. Bei einem Netzwerkdrucker müssen Sie den Computer auswählen, an den die gescannten Daten weiterleitet werden sollen. Der Scan-Standby-Bildschirm wird angezeigt. 5.
8. Drücken Sie zum Scannen in Farbe die Taste Farbe (Color) bzw. zum Scannen in Schwarzweiß die Taste Schwarz (Black). • Bei Auswahl von JPEG für Format im Scan-Einstellungsbildschirm: Das Gerät startet den Scanvorgang, und die gescannten Daten werden an den Computer gesendet und an eine E-Mail angehängt.
Speichern von gescannten Daten auf der Speicherkarte mithilfe des Bedienfelds am Gerät Sie können gescannte Daten auf der Speicherkarte mithilfe des Bedienfelds speichern.
4. Wählen Sie Speicherkarte (Memory card) aus, und drücken Sie dann die Taste OK. 5. Wählen Sie Auf Speicherkarte speichern (Save to memory card) aus, und drücken Sie dann die Taste OK. Der Scan-Standby-Bildschirm wird angezeigt. 6. Verwenden Sie die Taste , um den Dokumenttyp auszuwählen. Dokument (Document) Scannt das Original auf der Auflagefläche als Dokumentdaten, wobei die unter Scaneinstellg. (Scan settings) angegebenen Einstellungen angewendet werden.
• Bei Auswahl der Einstellung PDF oder Kompakt-PDF (Compact PDF) für Format im ScanEinstellungsbildschirm: Nach Abschluss des Scanvorgangs wird der Bestätigungsbildschirm mit der Frage, ob weitere Dokumente gescannt werden sollen, angezeigt. Wenn Sie mit dem Scannen fortfahren möchten, legen Sie das Original auf die Auflagefläche, und starten Sie den Scanvorgang. Drücken Sie die linke Taste Funktion (Function), wenn Sie den Scanvorgang abgeschlossen haben.
Löschen gescannter Daten auf der Speicherkarte Sie können gescannte Daten auf der Speicherkarte mithilfe des Bedienfelds löschen. 1. Stellen Sie sicher, dass das Gerät eingeschaltet ist. 2. Wählen Sie Scannen (Scan) im Bildschirm HOME. LCD-Anzeige und Bedienfeld Der Bildschirm zur Auswahl des Mediums, auf das Sie Daten speichern möchten, wird angezeigt.
1. Formatwechs. (Switch format) Mit der linken Taste Funktion (Function) können Sie zwischen der PDF-Datenliste und der JPEG-Datenliste wechseln. 2. Anzeige ändern Mit der mittleren Taste Funktion (Function) können Sie die Anzeige zwischen der Liste und der Vorschau wechseln. Wenn das Format für die PDF-Daten ausgewählt wird, ist auf der LCD-Anzeige nur die erste Seite der PDF-Daten zu sehen. 6. Wählen Sie mit den Tasten die zu löschende Datei aus, und drücken Sie dann die Taste OK. 7.
Vornehmen von Einstellungen über das Bedienfeld am Gerät Sie können Scaneinstellungen wie Scanformat, Auflösung oder Datenformat ändern. Wenn der Scan-Standby-Bildschirm angezeigt wird, drücken Sie die rechte Taste Funktion (Function), um das Einstellungselement aus, und das Einstellungselement auszuwählen. Wählen Sie mit der Taste legen Sie mit der Taste die Einstellung fest. Drücken Sie dann die Taste OK.
1. Scangrö. (Scan size) Wählen Sie die Größe des Originaldokuments aus. 2. Format Wählen Sie das Datenformat der gescannten Daten aus. 3. Scanaufl. (Scan res) (Scanauflösung) Wählen Sie die Scanauflösung aus. 4. Vorschau (Preview) Wählen Sie beim Speichern der Daten auf eine Speicherkarte aus, ob eine Vorschau der gescannten Daten angezeigt werden soll. 5. Durchschein. redu.
Netzwerk-Scan-Einstellungen Sie können Ihren Scanner oder Drucker mit einem Netzwerk verbinden, damit er von mehreren Computern verwendet werden kann oder Bilder in einen bestimmten Computer gescannt werden können. Wichtig Es können nicht mehrere Benutzer gleichzeitig scannen. Hinweis Nehmen Sie die Netzwerkeinstellungen für Ihren Scanner oder Drucker vorher über die Installations-CD-ROM oder anhand der Anweisungen auf der Webseite vor.
Hinweis Wird das Symbol nicht im Benachrichtigungsbereich des Desktops angezeigt, folgen Sie der unten stehenden Vorgehensweise. Windows 8: Klicken Sie auf dem Startbildschirm auf IJ Network Scanner Selector EX. Wenn IJ Network Scanner Selector EX nicht auf dem Startbildschirm angezeigt wird, wählen Sie den Charm Suchen (Search) aus und suchen Sie nach „IJ Network Scanner Selector EX“.
Einstellung zum Scannen mit IJ Scan Utility Um unter Verwendung von IJ Scan Utility mit einem Scanner oder Drucker in einem Netzwerk zu scannen, geben Sie Ihren Scanner oder Drucker in IJ Network Scanner Selector EX an, und befolgen Sie die nachstehenden Anweisungen, um den Verbindungsstatus zwischen dem Gerät und dem Computer zu ändern. 1. Starten Sie IJ Scan Utility. 2. Wählen Sie "Canon XXX series Network" (wobei "XXX" für den Modellnamen steht) unter Produktname (Product Name) aus.
Wird IJ Network Scanner Selector EX ausgeführt, wird im Benachrichtigungsbereich der Taskleiste ein entsprechendes Symbol angezeigt. Klicken Sie auf , um auch die verborgenen Symbole zu prüfen. Hinweis Wird das Symbol nicht im Benachrichtigungsbereich des Desktops angezeigt, folgen Sie der unten stehenden Vorgehensweise. Windows 8: Klicken Sie auf dem Startbildschirm auf IJ Network Scanner Selector EX.
Hinweis Wird Ihr Scanner oder Drucker nicht angezeigt, überprüfen Sie folgende Bedingungen, und klicken Sie auf OK, um den Bildschirm zu schließen. Öffnen Sie ihn dann erneut, und versuchen Sie, das Gerät auszuwählen. MP Drivers ist installiert.
Mit IJ Scan Utility ein Verhalten für Befehle vom Bedienfeld auswählen Mit IJ Scan Utility können Sie das Verhalten für das Scannen über das Bedienfeld festlegen. Hinweis Die Bildschirme zum Festlegen des Verhaltens für das automatische Scannen über das Bedienfeld werden in den folgenden Beschreibungen als Beispiele verwendet. 1. Starten Sie IJ Scan Utility. 2. Klicken Sie auf Einst... (Settings...). Das Dialogfeld Einstellungen wird angezeigt. 3.
Hinweis Nachstehend finden Sie weitere Informationen. Dialogfeld Einstellungen (Auf PC speichern (automatisch)) Dialogfeld Einstellungen (Auf PC speichern (Foto)) Dialogfeld Einstellungen (Auf PC speichern (Dokument)) Dialogfeld Einstellungen (An E-Mail anhängen (Foto)) Dialogfeld Einstellungen (An E-Mail anhängen (Dokument)) 4. Legen Sie Bildkorrekturen unter Scan-Optionen (Scan Options) fest. 5. Geben Sie den Dateinamen und andere Einstellungen unter Speichereinstellungen (Save Settings) an.
6. Wählen Sie Anwendung, die nach dem Scannen gestartet werden soll, unter Anwendungseinstellungen (Application Settings) aus. 7. Klicken Sie auf OK. Die Vorgänge werden gemäß den festgelegten Einstellungen durchgeführt, wenn Sie den Scanvorgang über das Bedienfeld starten.
Scannen im Zugriffspunktmodus Wenn sich das Gerät im Zugriffspunktmodus befindet, können Sie von einem externen Gerät – wie einem Computer oder einem Smartphone – scannen, ohne dass dafür ein Zugriffspunkt erforderlich ist. Wichtig • Bevor Sie das Gerät im Zugriffspunktmodus verwenden, müssen Sie den Namen des Zugriffspunkts vom Gerät und die Sicherheitseinstellung angeben. Vor der Verwendung des Geräts im Zugriffspunktmodus 1. Stellen Sie sicher, dass das Gerät eingeschaltet ist. 2.
Führen Sie den Scanvorgang vom externen Gerät durch und geben Sie das Gerät als verwendeten Scanner an. Hinweis • Details zum Scannen von einem externen Gerät, wie einem Computer oder einem Smartphone, via WLAN finden Sie in der Bedienungsanleitung des Geräts oder des Programms. • Sie können auch anhand von PIXMA Printing Solutions scannen. 8. Drücken Sie die linke Taste Funktion (Function), wenn der Scanvorgang beendet ist. Das Gerät beendet den Zugriffspunktmodus. 9.