MG7100 series Príručka online Skenovanie slovenčina (Slovak)
Obsah Skenovanie. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Skenovanie z počítača. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Skenovanie pomocou aplikácie IJ Scan Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Čo je aplikácia IJ Scan Utility (softvér skenera)?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Obrazovky programu ScanGear (ovládača skenera). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Karta Základný režim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Karta Rozšírený režim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Nastavenia vstupu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Skenovanie Skenovanie z počítača Skenovanie pomocou aplikácie IJ Scan Utility Skenovanie pomocou používaného aplikačného softvéru (ScanGear) Užitočné informácie o skenovaní Ponuka a obrazovka nastavení aplikácie IJ Network Scanner Selector EX Ďalšie skenovacie postupy Umiestnenie položiek (pri skenovaní z počítača) Skenovanie z ovládacieho panela zariadenia Odosielanie naskenovaných údajov do počítača pomocou ovládacieho panela zariadenia Základné Pripojenie naskenovaných údajov k e-mailu pomocou ovládacieh
Skenovanie z počítača Skenovanie pomocou aplikácie IJ Scan Utility Skenovanie pomocou používaného aplikačného softvéru (ScanGear) Užitočné informácie o skenovaní Ponuka a obrazovka nastavení aplikácie IJ Network Scanner Selector EX Ďalšie skenovacie postupy Umiestnenie položiek (pri skenovaní z počítača) 5
Skenovanie pomocou aplikácie IJ Scan Utility Čo je aplikácia IJ Scan Utility (softvér skenera)? Spustenie aplikácie IJ Scan Utility Jednoduché skenovanie pomocou funkcie automatického skenovania Základné Skenovanie fotografií Skenovanie dokumentov Skenovanie pomocou obľúbených nastavení Skenovanie položiek väčších ako ploché predlohové sklo (Spojenie obrázkov) Skenovanie viacerých položiek naraz Ukladanie po kontrole výsledkov skenovania Odosielanie naskenovaných obrázkov prostredníctvom e-mailu Extrakcia
Čo je aplikácia IJ Scan Utility (softvér skenera)? IJ Scan Utility je aplikácia, ktorá umožňuje jednoducho skenovať fotografie, dokumenty a pod. Kliknutím na príslušnú ikonu na hlavnej obrazovke aplikácie IJ Scan Utility môžete naraz vykonať všetky úkony, od skenovania po uloženie. Funkcie aplikácie IJ Scan Utility Jednoduché skenovanie podľa plánovaného účelu Pred skenovaním stačí kliknúť na príslušnú ikonu zodpovedajúcu typu položky alebo plánovanému účelu.
Integrácia s aplikáciami Naskenované obrázky môžete používať prostredníctvom integrácie s inými aplikáciami, zobraziť v obľúbenej aplikácii, pripojiť k e-mailom, extrahovať z nich text atď. Dôležité Niektoré funkcie sú dostupné iba v prípade, ak je nainštalovaná aplikácia My Image Garden. Poznámka Postup nastavenia aplikácií na integráciu nájdete v časti „Dialógové okno Nastavenia“.
Spustenie aplikácie IJ Scan Utility Poznámka Ak máte viac než jeden skener alebo ste zmenili pripojenie USB na sieťové pripojenie, nastavte sieťové prostredie z aplikácie IJ Scan Utility. Nastavenia skenovania v sieti Podľa krokov nižšie spustite aplikáciu IJ Scan Utility. Windows 8: Aplikáciu IJ Scan Utility spustite výberom položky IJ Scan Utility na domovskej obrazovke.
Jednoduché skenovanie pomocou funkcie automatického skenovania Vďaka automatickému zisťovaniu typu položky môžete jednoducho skenovať. Dôležité Nasledujúce typy položiek sa nemusia naskenovať správne. V takom prípade upravte rámy orezania (oblasti skenovania) pri zobrazení celého obrázka v programe ScanGear (ovládači skenera) a zopakujte skenovanie. Fotografie s belavým pozadím Položky vytlačené na bielom papieri, dokumenty písané rukou, vizitky a pod. Tenké položky Hrubé položky 1.
Nastavenia (Automatické skenovanie) (Settings (Auto Scan)) môžete vybrať aj rozšírené nastavenia skenovania. Ak chcete skenovať po výbere typu položky, pozrite si nasledujúce stránky.
Skenovanie fotografií Fotografie umiestnené na predlohovom skle môžete skenovať pomocou nastavení, ktoré sú vhodné pre fotografie. 1. Umiestnite fotografiu na predlohové sklo. Umiestnenie položiek (pri skenovaní z počítača) 2. Spustite aplikáciu IJ Scan Utility. 3. Kliknite na tlačidlo Nastavenia (Settings...), vyberte dialógové okno Nastavenia (Skenovanie fotografií) (Settings (Photo Scan)) a podľa potreby nastavte veľkosť papiera, rozlíšenie a iné parametre položky.
Skenovanie dokumentov Položky umiestnené na predlohovom skle môžete skenovať pomocou nastavení, ktoré sú vhodné pre dokumenty. 1. Umiestnite položku na predlohové sklo. Umiestnenie položiek (pri skenovaní z počítača) 2. Spustite aplikáciu IJ Scan Utility. 3. Kliknite na tlačidlo Nastavenia (Settings...), vyberte dialógové okno Nastavenia (Skenovanie dokumentov) (Settings (Document Scan)) a podľa potreby nastavte veľkosť papiera, rozlíšenie a iné parametre položky.
Skenovanie pomocou obľúbených nastavení Položky umiestnené na predlohovom skle môžete skenovať pomocou obľúbených nastavení, ktoré ste predtým uložili. Táto funkcia je užitočná na uloženie často používaných nastavení alebo pri výbere podrobných nastavení skenovania. 1. Spustite aplikáciu IJ Scan Utility. 2. Kliknite na tlačidlo Nastavenia (Settings...), vyberte dialógové okno Nastavenia (Vlastné skenovanie) (Settings (Custom Scan)) a nastavte výber zdroja, rozlíšenie a iné parametre položky.
Skenovanie položiek väčších ako ploché predlohové sklo (Spojenie obrázkov) Môžete naskenovať ľavú a pravú polovicu položky väčšej ako predlohové sklo a naskenované polovice potom znova spojiť do jedného obrázka. Podporujú sa položky, ktoré sú približne dvakrát také veľké ako predlohové sklo. Poznámka V nasledujúcom postupe sa vysvetľuje skenovanie položky, ktorá sa má umiestniť naľavo. 1. Spustite aplikáciu IJ Scan Utility. 2. Kliknite na tlačidlo Nastavenia (Settings...
5. Uistite sa, že v časti Smer skenovania (Scan Direction) je vybratá možnosť Skenovať zľava (Scan from Left). 6. Na predlohové sklo umiestnite lícovou stranou nadol položku, ktorú chcete zobraziť v ľavej časti obrazovky. 7. Kliknite na tlačidlo Spustiť skenovanie obrázka 1 (Start Scanning Image 1).
Prvá položka sa naskenuje a zobrazí v časti 1. Poznámka Kliknutím na tlačidlo Zrušiť (Cancel) môžete skenovanie zrušiť. 8. Na predlohové sklo umiestnite lícovou stranou nadol položku, ktorú chcete zobraziť v pravej časti obrazovky. 9. Kliknite na tlačidlo Spustiť skenovanie obrázka 2 (Start Scanning Image 2).
Druhá položka sa naskenuje a zobrazí v časti 2. Poznámka Kliknutím na tlačidlo Zrušiť (Cancel) môžete skenovanie zrušiť. 10. Naskenované obrázky upravte podľa potreby. Pomocou panela s nástrojmi otočte, priblížte alebo vzdiaľte obrázky, prípadne ich presuňte na požadované miesta.
Poznámka Začiarknutím políčka Upraviť rámy orezania (Adjust cropping frames) určte oblasť, ktorú chcete uložiť. Úprava rámov orezania v okne Spojenie obrázkov Ak chcete položku znova naskenovať, vyberte príslušný obrázok v oblasti ukážky alebo miniatúr v hornej časti obrazovky a kliknite na položku (Odstrániť). Vybratý obrázok sa odstráni, vďaka čomu môžete položku znova naskenovať. 11. Kliknite na tlačidlo Uložiť (Save). Spojený obrázok sa uloží.
Skenovanie viacerých položiek naraz Môžete naraz naskenovať dve alebo viac fotografií (malých položiek) umiestnených na predlohovom skle a potom ich samostatne uložiť. Dôležité Nasledujúce typy položiek sa nemusia naskenovať správne. V takom prípade upravte rámy orezania (oblasti skenovania) pri zobrazení celého obrázka v programe ScanGear (ovládači skenera) a zopakujte skenovanie. Fotografie s belavým pozadím Položky vytlačené na bielom papieri, dokumenty písané rukou, vizitky a pod.
Zobrazí sa dialógové okno nastavení. 4. Kliknite na tlačidlo Vlastné skenovanie (Custom Scan). 5. Vyberte možnosť Výber zdroja (Select Source) podľa skenovaných položiek.
6. V časti Veľkosť papiera (Paper Size) vyberte položku Automatické skenovanie (Auto scan) a kliknite na tlačidlo OK. Zobrazí sa hlavná obrazovka aplikácie IJ Scan Utility. Poznámka Podrobné informácie o položkách nastavenia v dialógovom okne nastavení nájdete na nasledujúcich stránkach.
Dialógové okno Nastavenia (Vlastné skenovanie) 7. Kliknite na tlačidlo Vlastné (Custom). Viacero položiek sa naskenuje naraz. Poznámka Kliknutím na tlačidlo Zrušiť (Cancel) môžete skenovanie zrušiť. Naskenované obrázky sa uložia do priečinka nastaveného v časti Uložiť do (Save in) príslušného dialógového okna nastavení, ktoré zobrazíte kliknutím na tlačidlo Nastavenia (Settings...). V jednotlivých dialógových oknách nastavení môžete vybrať aj rozšírené nastavenia skenovania.
Ukladanie po kontrole výsledkov skenovania Môžete skontrolovať výsledky skenovania a potom obrázky uložiť v počítači. Dôležité Ak skenujete pomocou funkcie Automaticky (Auto) alebo ovládacieho panela, pred uložením nemôžete výsledky skenovania skontrolovať. Poznámka V nasledujúcich opisoch sa ako príklady používajú obrazovky skenovania fotografií. 1. Spustite aplikáciu IJ Scan Utility. 2. Kliknite na tlačidlo Nastavenia (Settings...). Zobrazí sa dialógové okno nastavení. 3.
4. Začiarknite políčko Skontrolovať výsledky skenovania (Check scan results) a kliknite na tlačidlo OK. Zobrazí sa hlavná obrazovka aplikácie IJ Scan Utility. Poznámka Podrobné informácie o položkách nastavenia v dialógovom okne nastavení nájdete na nasledujúcich stránkach. Dialógové okno Nastavenia (Skenovanie fotografií) Dialógové okno Nastavenia (Skenovanie dokumentov) Dialógové okno Nastavenia (Vlastné skenovanie) Dialógové okno Nastavenia (Naskenovať a spojiť) Dialógové okno Nastavenia (ScanGear) 5.
Poznámka Kliknutím na tlačidlo Zrušiť (Cancel) môžete skenovanie zrušiť. 6. Podľa potreby zmeňte poradie obrázkov alebo možnosti ukladania súborov. Poradie obrázkov alebo možnosti ukladania súborov môžete zmeniť v dialógovom okne Nastavenia ukladania (Save Settings). Poznámka Nižšie sú uvedené predvolené priečinky na ukladanie.
Odosielanie naskenovaných obrázkov prostredníctvom e-mailu Naskenované obrázky môžete odoslať prostredníctvom e-mailu. Poznámka V nasledujúcich opisoch sa ako príklady používajú obrazovky skenovania fotografií. 1. Spustite aplikáciu IJ Scan Utility. 2. Kliknite na tlačidlo Nastavenia (Settings...). Zobrazí sa dialógové okno nastavení. 3. Kliknite na tlačidlo Skenovanie fotografií (Photo Scan).
4. V časti Nastavenia aplikácie (Application Settings) vyberte položku Pripojiť k e-mailu (Attach to e-mail) a potom vyberte e-mailového klienta. Poznámka Z rozbaľovacej ponuky môžete vybrať e-mailových klientov, ktorých chcete používať na odosielanie príloh. Ak je vybratá možnosť Žiadna (pripojiť manuálne) (None (Attach Manually)), naskenované a uložené obrázky pripojte k e-mailu ručne. 5. Kliknite na tlačidlo OK.
Zobrazí sa hlavná obrazovka aplikácie IJ Scan Utility. Poznámka Podrobné informácie o položkách nastavenia v dialógovom okne nastavení nájdete na nasledujúcich stránkach. Dialógové okno Nastavenia (Automatické skenovanie) Dialógové okno Nastavenia (Skenovanie fotografií) Dialógové okno Nastavenia (Skenovanie dokumentov) Dialógové okno Nastavenia (Vlastné skenovanie) Dialógové okno Nastavenia (ScanGear) 6. Kliknite na tlačidlo Fotografie (Photo). Spustí sa skenovanie.
Naskenované obrázky sa uložia podľa nastavení vybratých v dialógovom okne nastavení. Ak v dialógovom okne nastavení začiarknete políčko Skontrolovať výsledky skenovania (Check scan results), zobrazí sa dialógové okno Nastavenia ukladania (Save Settings). Po nastavení možností ukladania a kliknutí na tlačidlo OK sa naskenované obrázky uložia a automaticky pripoja k novej správe vo vybratom e-mailovom klientovi. 7. Zadajte príjemcu, predmet a text správy a odošlite e-mail.
Extrakcia textu z naskenovaných obrázkov (OCR) Naskenujte text z časopisov a novín a zobrazte ho v programe Poznámkový blok (súčasť systému Windows). Poznámka Text môžete extrahovať pri skenovaní pomocou funkcie Dokument (Document), Vlastné (Custom) alebo ScanGear. V nasledujúcich opisoch sa ako príklady používajú obrazovky skenovania dokumentov. 1. Spustite aplikáciu IJ Scan Utility. 2. Kliknite na tlačidlo Nastavenia (Settings...). Zobrazí sa dialógové okno nastavení. 3.
Poznámka Ak je v oblasti Nastavenia aplikácie (Application Settings) vybratá položka Spustiť funkciu OCR (Start OCR), položku Rozlíšenie (Resolution) možno nastaviť len na hodnotu 300 dpi alebo 400 dpi. 4. V časti Nastavenia aplikácie (Application Settings) vyberte položku Spustiť funkciu OCR (Start OCR) a potom aplikáciu, v ktorej chcete zobraziť výsledok.
Zobrazí sa hlavná obrazovka aplikácie IJ Scan Utility. Poznámka Podrobné informácie o položkách nastavenia v dialógovom okne nastavení nájdete na nasledujúcich stránkach. Dialógové okno Nastavenia (Skenovanie dokumentov) Dialógové okno Nastavenia (Vlastné skenovanie) Dialógové okno Nastavenia (ScanGear) 6. Kliknite na tlačidlo Dokument (Document). Spustí sa skenovanie. Po dokončení skenovania sa naskenované obrázky uložia podľa príslušných nastavení a extrahovaný text sa zobrazí vo vybratej aplikácii.
dokumenty obsahujúce text s veľkosťou písma mimo rozsahu 8 až 40 bodov (pri rozlíšení 300 dpi), zošikmené dokumenty, dokumenty umiestnené obrátene alebo dokumenty s textom s nesprávnou orientáciou (pootočené znaky), dokumenty obsahujúce špeciálne písma, efekty, kurzívu alebo rukou písaný text, dokumenty s úzkym riadkovaním, dokumenty s farebným pozadím textu, dokumenty obsahujúce viaceré jazyky.
Obrazovky aplikácie IJ Scan Utility Hlavná obrazovka aplikácie IJ Scan Utility Dialógové okno Nastavenia Dialógové okno Nastavenia (Automatické skenovanie) Dialógové okno Nastavenia (Skenovanie fotografií) Dialógové okno Nastavenia (Skenovanie dokumentov) Dialógové okno Nastavenia (Vlastné skenovanie) Dialógové okno Nastavenia (Naskenovať a spojiť) Dialógové okno Nastavenia (ScanGear) Dialógové okno Nastavenia (Uložiť v počítači (automaticky)) Dialógové okno Nastavenia (Uložiť v počítači (fotografie)) Dialó
Hlavná obrazovka aplikácie IJ Scan Utility Podľa krokov nižšie spustite aplikáciu IJ Scan Utility. Windows 8: Aplikáciu IJ Scan Utility spustite výberom položky IJ Scan Utility na domovskej obrazovke. Ak sa aplikácia IJ Scan Utility na domovskej obrazovke nezobrazuje, vyberte kľúčové tlačidlo Vyhľadávanie (Search) a vyhľadajte výraz „IJ Scan Utility“.
Umožňuje naskenovať položky ako dokumenty a uložiť ich v počítači. Nastavenia skenovania a ukladania, ako aj odpoveď po skenovaní možno vybrať v dialógovom okne Nastavenia (Skenovanie dokumentov) (Settings (Document Scan)). • Vlastné (Custom) Umožňuje naskenovať položky pomocou obľúbených nastavení a obrázky uložiť v počítači. Typ položky sa môže zistiť automaticky.
Dialógové okno Nastavenia Dialógové okno nastavení obsahuje tri karty: (Skenovanie z počítača), (Skenovanie pomocou ovládacieho panela) a (Všeobecné nastavenia). Po kliknutí na kartu sa zobrazenie prepne na zobrazenie v červenom ráme a vy môžete vybrať rozšírené nastavenia funkcií na jednotlivých kartách. Karta (Skenovanie z počítača) Môžete určiť odpovede pri skenovaní pomocou aplikácie IJ Scan Utility alebo My Image Garden.
Dialógové okno Nastavenia (Pripojiť k e-mailu (fotografie)) Dialógové okno Nastavenia (Pripojiť k e-mailu (dokument)) Dôležité Ak dialógové okno nastavení zobrazíte z aplikácie My Image Garden, karta (Skenovanie pomocou ovládacieho panela) sa nezobrazí. Pri používaní skenera alebo tlačiarne so sieťovým pripojením sa dialógové okno Nastavenia (Uložiť v počítači (automaticky)) (Settings (Save to PC (Auto))) nezobrazí.
Dialógové okno Nastavenia (Automatické skenovanie) Kliknutím na položku Automatické skenovanie (Auto Scan) na karte (Skenovanie z počítača) zobrazíte dialógové okno Nastavenia (Automatické skenovanie) (Settings (Auto Scan)). V dialógovom okne Nastavenia (Automatické skenovanie) (Settings (Auto Scan)) môžete vybrať rozšírené nastavenia na skenovanie s automatickým zistením typu položky.
(Document) alebo Vlastné (Custom). Pri použití funkcie Automaticky (Auto) nenaskenujete položky správne. Fotografie veľkosti A4 Textové dokumenty menšej veľkosti ako 2L (127 x 178 mm) (5 x 7 palcov), napríklad brožované strany s odrezanou väzbou Položky vytlačené na tenkom bielom papieri Dlhé úzke položky, napríklad panoramatické fotografie Reflexné etikety diskov sa nemusia naskenovať tak, ako ste očakávali. Položky správne umiestnite na predlohové sklo.
- Fotografie, pohľadnice, disky BD, DVD alebo CD a vizitky: JPEG - Časopisy, noviny a dokumenty: PDF Dôležité Formát použitý pri ukladaní sa môže líšiť v závislosti od spôsobu umiestnenia položky. Umiestnenie položiek (pri skenovaní z počítača) Poznámka Formát údajov môžete zmeniť pomocou tlačidla Nastavenia... (Settings...). • Nastavenia (Settings...
Aplikáciu vyberte z rozbaľovacej ponuky. • Odoslať do priečinka (Send to a folder) Túto možnosť vyberte v prípade, že naskenované obrázky chcete okrem priečinka vybratého v ponuke Uložiť do (Save in) uložiť aj do iného priečinka. Priečinok vyberte z rozbaľovacej ponuky. • Pripojiť k e-mailu (Attach to e-mail) Túto možnosť vyberte v prípade, že chcete odosielať e-maily s pripojenými naskenovanými obrázkami. E-mailového klienta, ktorého chcete spustiť, vyberte z rozbaľovacej ponuky.
Dialógové okno Nastavenia (Skenovanie fotografií) Kliknutím na položku Skenovanie fotografií (Photo Scan) na karte (Skenovanie z počítača) zobrazíte dialógové okno Nastavenia (Skenovanie fotografií) (Settings (Photo Scan)). V dialógovom okne Nastavenia (Skenovanie fotografií) (Settings (Photo Scan)) môžete vybrať rozšírené nastavenia na skenovanie jednotlivých položiek ako fotografií.
Vyberte režim farieb, v ktorom chcete naskenovať požadovanú položku. Dôležité Ak chcete vybrať položku Čiernobielo (Black and White), zrušte začiarknutie políčka Komprimovať naskenované obrázky pri prenose (Compress scanned images upon transfer). • Veľkosť papiera (Paper Size) Vyberte veľkosť položky, ktorú chcete naskenovať. Po výbere možnosti Vlastné (Custom) sa zobrazí obrazovka, na ktorej môžete vybrať veľkosť papiera.
Slúži na zvýraznenie obrysu objektov a zostrenie snímky. (2) Oblasť Nastavenia ukladania • Názov súboru (File Name) Zadajte názov súboru obrázka, ktorý chcete uložiť. Pri ukladaní súboru sa k nastavenému názvu súboru pripojí dátum a štyri číslice vo formáte „_20XX0101_0001“. • Formát údajov (Data Format) Vyberte formát údajov, v ktorom chcete ukladať naskenované obrázky. Môžete vybrať formát JPEG/Exif, TIFF alebo PNG.
Dôležité Ak dialógové okno nastavení zobrazíte z aplikácie My Image Garden, táto možnosť sa nezobrazí. (3) Oblasť Nastavenia aplikácie • Otvoriť v aplikácii (Open with an application) Túto možnosť vyberte v prípade, že chcete zlepšiť alebo korigovať naskenované obrázky. Aplikáciu vyberte z rozbaľovacej ponuky. • Odoslať do aplikácie (Send to an application) Túto možnosť vyberte v prípade, že chcete naskenované obrázky používať v aplikácii umožňujúcej ich prehľadávanie alebo usporiadanie.
Dialógové okno Nastavenia (Skenovanie dokumentov) Kliknutím na položku Skenovanie dokumentov (Document Scan) na karte (Skenovanie z počítača) zobrazíte dialógové okno Nastavenia (Skenovanie dokumentov) (Settings (Document Scan)). V dialógovom okne Nastavenia (Skenovanie dokumentov) (Settings (Document Scan)) môžete vybrať rozšírené nastavenia na skenovanie jednotlivých položiek ako dokumentov.
Skenovanie dokumentov: Dokument (Document) Skenovanie časopisov: Časopis (Magazine) • Režim farieb (Color Mode) Vyberte režim farieb, v ktorom chcete naskenovať požadovanú položku. Dôležité Ak chcete vybrať položku Čiernobielo (Black and White), zrušte začiarknutie políčka Komprimovať naskenované obrázky pri prenose (Compress scanned images upon transfer). • Veľkosť papiera (Paper Size) Vyberte veľkosť položky, ktorú chcete naskenovať.
• Nastavenia spracovania obrázkov (Image Processing Settings) Kliknutím na tlačidlo (plus) nastavte nasledujúce možnosti. Poznámka Ak je položka Režim farieb (Color Mode) nastavená na hodnotu Čiernobielo (Black and White), zobrazia sa iba možnosti Obmedziť tieň v oblasti väzby (Reduce gutter shadow), Skorigovať naklonený textový dokument (Correct slanted text document) a Zistiť orientáciu textového dokumentu a otočiť obrázok (Detect the orientation of text document and rotate image).
Dôležité K dispozícii je iba v prípade, že nezačiarknete políčko Komprimovať naskenované obrázky pri prenose (Compress scanned images upon transfer). Poznámka Pri skenovaní položiek s neštandardnou veľkosťou alebo vybratých oblastí opravte tieň v oblasti väzby pomocou karty Rozšírený režim (Advanced Mode) programu ScanGear (ovládača skenera). Podrobné informácie nájdete v časti „Korekcia tieňa v oblasti väzby“ pre svoj model z obrazovky Domov dokumentu Príručka online.
Orientácia sa nemusí zistiť pre nasledujúce typy nastavení dokumentov, pretože nebude možné správne rozpoznať text: rozlíšenie mimo rozsahu 300 až 600 dpi, veľkosť písma mimo rozsahu 8 až 48 bodov, dokumenty obsahujúce špeciálne písma, efekty, kurzívu alebo rukou písaný text, dokumenty so vzorom na pozadí. V takom prípade začiarknite políčko Skontrolovať výsledky skenovania (Check scan results) a otočte obrázok v dialógovom okne Nastavenia ukladania (Save Settings).
Windows 8: priečinok Moje dokumenty (My Documents) Windows 7: priečinok Moje dokumenty (My Documents) Windows Vista: priečinok Dokumenty (Documents) Windows XP: priečinok Moje dokumenty (My Documents) Dôležité Ak dialógové okno nastavení zobrazíte z aplikácie My Image Garden, táto možnosť sa nezobrazí. • Skontrolovať výsledky skenovania (Check scan results) Po skenovaní sa zobrazí dialógové okno Nastavenia ukladania (Save Settings).
Umožňuje ukladať do priečinka vybratého v časti Uložiť do (Save in). Poznámka Aplikáciu alebo priečinok vyberte v dialógovom okne Vyberte aplikáciu (Select Application) alebo Vyberte cieľový priečinok (Select Destination Folder), ktoré zobrazíte výberom možnosti Pridať... (Add...) z rozbaľovacej ponuky. • Pokyny (Instructions) Otvorí túto príručku. • Predvolené (Defaults) Na zobrazenej obrazovke môžete obnoviť predvolené hodnoty nastavení.
Dialógové okno Nastavenia (Naskenovať a spojiť) Kliknutím na položku Naskenovať a spojiť (Scan and Stitch) na karte (Skenovanie z počítača) zobrazíte dialógové okno Nastavenia (Naskenovať a spojiť) (Settings (Scan and Stitch)). V dialógovom okne Nastavenia (Naskenovať a spojiť) (Settings (Scan and Stitch)) môžete vybrať rozšírené nastavenia na skenovanie položiek väčších ako predlohové sklo.
Poznámka Ak chcete obmedziť zrnitosť, nastavte položku Výber zdroja (Select Source) na hodnotu Časopis (Magazine). • Režim farieb (Color Mode) Vyberte režim farieb, v ktorom chcete naskenovať požadovanú položku. • Rozlíšenie (Resolution) Vyberte rozlíšenie položky, ktorú chcete naskenovať. Čím je hodnota rozlíšenia vyššia, tým je obrázok detailnejší. Rozlíšenie • Nastavenia spracovania obrázkov (Image Processing Settings) (plus) nastavte nasledujúce možnosti.
(2) Oblasť Nastavenia ukladania • Názov súboru (File Name) Zadajte názov súboru obrázka, ktorý chcete uložiť. Pri ukladaní súboru sa k nastavenému názvu súboru pripojí dátum a štyri číslice vo formáte „_20XX0101_0001“. • Formát údajov (Data Format) Vyberte formát údajov, v ktorom chcete ukladať naskenované obrázky. Môžete vybrať formát JPEG/Exif, TIFF, PNG, PDF alebo PDF (viaceré strany) (PDF (Multiple Pages)).
(3) Oblasť Nastavenia aplikácie • Otvoriť v aplikácii (Open with an application) Túto možnosť vyberte v prípade, že chcete zlepšiť alebo korigovať naskenované obrázky. Aplikáciu vyberte z rozbaľovacej ponuky. • Odoslať do aplikácie (Send to an application) Túto možnosť vyberte v prípade, že chcete naskenované obrázky používať v aplikácii umožňujúcej ich prehľadávanie alebo usporiadanie. Aplikáciu vyberte z rozbaľovacej ponuky.
Dialógové okno Nastavenia (ScanGear) Kliknutím na položku ScanGear na karte (Skenovanie z počítača) zobrazíte dialógové okno Nastavenia (ScanGear) (Settings (ScanGear)). V dialógovom okne Nastavenia (ScanGear) (Settings (ScanGear)) môžete vybrať spôsob ukladania naskenovaných položiek po spustení programu ScanGear (ovládača skenera), ako aj odpoveď po ich uložení.
Poznámka Po výbere formátu PDF alebo PDF (viaceré strany) (PDF (Multiple Pages)) možno skenovať obrázky s rozlíšením až 9600 x 9600 pixlov. Ak je v časti Nastavenia ukladania (Save Settings) začiarknuté políčko Povoliť skenovanie veľkých obrázkov (Enable large image scans) alebo ak je v časti Nastavenia aplikácie (Application Settings) vybratá položka Spustiť funkciu OCR (Start OCR), môžete vybrať formát JPEG/Exif, TIFF alebo PNG. • Nastavenia (Settings...
Poznámka Ak toto políčko nie je začiarknuté, možno skenovať obrázky s maximálnym rozlíšením 10208 x 14032 pixlov. • Skontrolovať výsledky skenovania (Check scan results) Po skenovaní sa zobrazí dialógové okno Nastavenia ukladania (Save Settings). Dôležité Ak dialógové okno nastavení zobrazíte z aplikácie My Image Garden, táto možnosť sa nezobrazí.
Poznámka Aplikáciu alebo priečinok vyberte v dialógovom okne Vyberte aplikáciu (Select Application) alebo Vyberte cieľový priečinok (Select Destination Folder), ktoré zobrazíte výberom možnosti Pridať... (Add...) z rozbaľovacej ponuky. • Pokyny (Instructions) Otvorí túto príručku. • Predvolené (Defaults) Na zobrazenej obrazovke môžete obnoviť predvolené hodnoty nastavení.
Dialógové okno Nastavenia (Uložiť v počítači (automaticky)) Kliknutím na položku Uložiť v počítači (automaticky) (Save to PC (Auto)) na karte (Skenovanie pomocou ovládacieho panela) zobrazíte dialógové okno Nastavenia (Uložiť v počítači (automaticky)) (Settings (Save to PC (Auto))). V dialógovom okne Nastavenia (Uložiť v počítači (automaticky)) (Settings (Save to PC (Auto))) môžete vybrať odpoveď pri ukladaní obrázkov do počítača po ich naskenovaní z ovládacieho panela s automatickým zistením typu položky.
Umožňuje automaticky použiť vhodné korekcie na základe typu položky. Dôležité V dôsledku korekcií sa môže farebný odtieň líšiť od pôvodného obrázka. V takom prípade zrušte začiarknutie políčka a spustite skenovanie. Poznámka Ak povolíte túto funkciu, skenovanie bude trvať dlhšie než zvyčajne. (2) Oblasť Nastavenia ukladania • Názov súboru (File Name) Zadajte názov súboru obrázka, ktorý chcete uložiť.
Windows 8: priečinok Moje dokumenty (My Documents) Windows 7: priečinok Moje dokumenty (My Documents) Windows Vista: priečinok Dokumenty (Documents) Windows XP: priečinok Moje dokumenty (My Documents) (3) Oblasť Nastavenia aplikácie • Otvoriť v aplikácii (Open with an application) Túto možnosť vyberte v prípade, že chcete zlepšiť alebo korigovať naskenované obrázky. Aplikáciu vyberte z rozbaľovacej ponuky.
Dialógové okno Nastavenia (Uložiť v počítači (fotografie)) Kliknutím na položku Uložiť v počítači (fotografie) (Save to PC (Photo)) na karte (Skenovanie pomocou ovládacieho panela) zobrazíte dialógové okno Nastavenia (Uložiť v počítači (fotografie)) (Settings (Save to PC (Photo))). V dialógovom okne Nastavenia (Uložiť v počítači (fotografie)) (Settings (Save to PC (Photo))) môžete vybrať odpoveď pri ukladaní obrázkov do počítača (ako fotografií) po ich naskenovaní pomocou ovládacieho panela.
Umožňuje skomprimovať naskenované obrázky pri ich prenose do počítača. Táto možnosť je užitočná v prípade, že ste skener alebo tlačiareň spolu s počítačom pripojili k pomalému rozhraniu, napríklad USB1.1, alebo sieti. (2) Oblasť Nastavenia ukladania • Názov súboru (File Name) Zadajte názov súboru obrázka, ktorý chcete uložiť. Pri ukladaní súboru sa k nastavenému názvu súboru pripojí dátum a štyri číslice vo formáte „_20XX0101_0001“. • Formát údajov (Data Format) Nastavte pomocou ovládacieho panela.
Túto možnosť vyberte v prípade, že naskenované obrázky chcete okrem priečinka vybratého v ponuke Uložiť do (Save in) uložiť aj do iného priečinka. Priečinok vyberte z rozbaľovacej ponuky. • Nespustiť žiadnu aplikáciu (Do not start any application) Umožňuje ukladať do priečinka vybratého v časti Uložiť do (Save in).
Dialógové okno Nastavenia (Uložiť v počítači (dokument)) Kliknutím na položku Uložiť v počítači (dokument) (Save to PC (Document)) na karte (Skenovanie pomocou ovládacieho panela) zobrazíte dialógové okno Nastavenia (Uložiť v počítači (dokument)) (Settings (Save to PC (Document))). V dialógovom okne Nastavenia (Uložiť v počítači (dokument)) (Settings (Save to PC (Document))) môžete vybrať odpoveď pri ukladaní obrázkov do počítača (ako dokumentov) po ich naskenovaní pomocou ovládacieho panela.
Umožňuje skomprimovať naskenované obrázky pri ich prenose do počítača. Táto možnosť je užitočná v prípade, že ste skener alebo tlačiareň spolu s počítačom pripojili k pomalému rozhraniu, napríklad USB1.1, alebo sieti. • Nastavenia spracovania obrázkov (Image Processing Settings) Kliknutím na tlačidlo (plus) nastavte nasledujúce možnosti. • Použiť funkciu Automatická oprava dokumentov (Apply Auto Document Fix) Začiarknutím tohto políčka zostríte text v dokumente alebo časopise kvôli lepšej čitateľnosti.
text písaný rukou, dokumenty obsahujúce zvislé aj vodorovné čiary (tabuľky). Poznámka Ak povolíte možnosť Skorigovať naklonený textový dokument (Correct slanted text document), skenovanie bude trvať dlhšie než zvyčajne. • Zistiť orientáciu textového dokumentu a otočiť obrázok (Detect the orientation of text document and rotate image) Zistí sa orientácia textu v naskenovanom dokumente a obrázok sa automaticky otočí podľa správnej orientácie.
Destination Folder), ktoré zobrazíte výberom možnosti Pridať... (Add...) z rozbaľovacej ponuky. Nižšie sú uvedené predvolené priečinky na ukladanie.
Dialógové okno Nastavenia (Pripojiť k e-mailu (fotografie)) Kliknutím na položku Pripojiť k e-mailu (fotografie) (Attach to E-mail (Photo)) na karte (Skenovanie pomocou ovládacieho panela) zobrazíte dialógové okno Nastavenia (Pripojiť k e-mailu (fotografie)) (Settings (Attach to E-mail (Photo))).
Umožňuje skomprimovať naskenované obrázky pri ich prenose do počítača. Táto možnosť je užitočná v prípade, že ste skener alebo tlačiareň spolu s počítačom pripojili k pomalému rozhraniu, napríklad USB1.1, alebo sieti. (2) Oblasť Nastavenia ukladania • Názov súboru (File Name) Zadajte názov súboru obrázka, ktorý chcete uložiť. Pri ukladaní súboru sa k nastavenému názvu súboru pripojí dátum a štyri číslice vo formáte „_20XX0101_0001“. • Formát údajov (Data Format) Nastavte pomocou ovládacieho panela.
• Pokyny (Instructions) Otvorí túto príručku. • Predvolené (Defaults) Na zobrazenej obrazovke môžete obnoviť predvolené hodnoty nastavení.
Dialógové okno Nastavenia (Pripojiť k e-mailu (dokument)) Kliknutím na položku Pripojiť k e-mailu (dokument) (Attach to E-mail (Document)) na karte (Skenovanie pomocou ovládacieho panela) zobrazíte dialógové okno Nastavenia (Pripojiť k e-mailu (dokument)) (Settings (Attach to E-mail (Document))).
Umožňuje skomprimovať naskenované obrázky pri ich prenose do počítača. Táto možnosť je užitočná v prípade, že ste skener alebo tlačiareň spolu s počítačom pripojili k pomalému rozhraniu, napríklad USB1.1, alebo sieti. • Nastavenia spracovania obrázkov (Image Processing Settings) Kliknutím na tlačidlo (plus) nastavte nasledujúce možnosti. • Použiť funkciu Automatická oprava dokumentov (Apply Auto Document Fix) Začiarknutím tohto políčka zostríte text v dokumente alebo časopise kvôli lepšej čitateľnosti.
text písaný rukou, dokumenty obsahujúce zvislé aj vodorovné čiary (tabuľky). Poznámka Ak povolíte možnosť Skorigovať naklonený textový dokument (Correct slanted text document), skenovanie bude trvať dlhšie než zvyčajne. • Zistiť orientáciu textového dokumentu a otočiť obrázok (Detect the orientation of text document and rotate image) Zistí sa orientácia textu v naskenovanom dokumente a obrázok sa automaticky otočí podľa správnej orientácie.
Zobrazí priečinok na ukladanie naskenovaných snímok. Ak chcete zmeniť priečinok, kliknite na tlačidlo Pridať... (Add...) a zadajte cieľový priečinok v dialógovom okne Vyberte cieľový priečinok (Select Destination Folder). Nižšie sú uvedené predvolené priečinky na ukladanie.
Dialógové okno Nastavenia (Všeobecné nastavenia) Kliknutím na kartu (Všeobecné nastavenia) zobrazíte dialógové okno Nastavenia (Všeobecné nastavenia) (Settings (General Settings)). V dialógovom okne Nastavenia (Všeobecné nastavenia) (Settings (General Settings)) môžete nastaviť používaný produkt, obmedzenie veľkosti súborov týkajúce sa príloh emailov, jazyk na rozpoznanie textu na obrázkoch a priečinok na dočasné ukladanie obrázkov.
rozlíšenie 1024 x 768 systému Windows) (Large (Suitable for 1024 x 768 Windows)) alebo Bezo zmien (No Change). Dôležité Ak dialógové okno nastavení zobrazíte z aplikácie My Image Garden, táto možnosť sa nezobrazí. • Jazyk dokumentu (Document Language) Vyberte jazyk zisťovania textu na snímkach. • Priečinok na ukladanie dočasných súborov (Folder to Save Temporary Files) Zobrazí priečinok na dočasné ukladanie obrázkov. Kliknutím na tlačidlo Prehľadávať... (Browse...) zadajte cieľový priečinok.
Dialógové okno Nastavenia formátu údajov Dialógové okno Nastavenia formátu údajov (Data Format Settings) zobrazíte vykonaním jedného z nasledujúcich krokov. • Kliknutím na tlačidlo Nastavenia... (Settings...) v časti Nastavenia ukladania (Save Settings) na jednotlivých kartách dialógového okna nastavení • Kliknutím na tlačidlo Nastavenia... (Settings...
• Kompresia PDF (PDF Compression) Vyberte typ kompresie na ukladanie súborov PDF. • Štandardná (Standard) Odporúča sa, aby ste za normálnych okolností vybrali toto nastavenie. • Vysoká (High) Pri ukladaní sa veľkosť súboru skomprimuje, čo umožňuje znížiť zaťaženie siete alebo servera. Dôležité Táto možnosť sa nezobrazí, keď nastavenie Formát údajov (Data Format) na karte (Skenovanie z ovládacieho panela) dialógového okna nastavení je možnosť Použiť nastavenie zariadenia (Use Device Setting).
Dialógové okno Nastavenia ukladania Ak chcete po skenovaní zobraziť dialógové okno Nastavenia ukladania (Save Settings), v časti Nastavenia ukladania (Save Settings) dialógového okna nastavení začiarknite políčko Skontrolovať výsledky skenovania (Check scan results). Môžete určiť formát údajov a cieľové umiestnenie a zároveň zobraziť miniatúry výsledkov skenovania. Dôležité Po skenovaní z aplikácie My Image Garden alebo ovládacieho panela sa dialógové okno Nastavenia ukladania (Save Settings) nezobrazí.
Dôležité Tlačidlá operácií ukážky sa nezobrazia v prípade, ak je v dialógovom okne Nastavenia (ScanGear) (Settings (ScanGear)) začiarknuté políčko Povoliť skenovanie veľkých obrázkov (Enable large image scans). (2) Oblasť výsledkov skenovania Zobrazuje miniatúry naskenovaných obrázkov. Poradie ukladania obrázkov môžete zmeniť ich presunutím. Pod miniatúrami sa zobrazujú názvy súborov na uloženie. (3) Oblasť Nastavenia ukladania • Názov súboru (File Name) Zadajte názov súboru obrázka, ktorý chcete uložiť.
súborov PDF podľa kľúčových slov a typ ich kompresie, ako aj formát údajov, v ktorom sa majú ukladať obrázky naskenované pomocou funkcie automatického skenovania. • Uložiť do (Save in) Zobrazí priečinok na ukladanie naskenovaných snímok. Ak chcete zmeniť priečinok, zadajte cieľový priečinok v dialógovom okne Vyberte cieľový priečinok (Select Destination Folder), ktoré zobrazíte výberom možnosti Pridať... (Add...) z rozbaľovacej ponuky. Nižšie sú uvedené predvolené priečinky na ukladanie.
Okno Spojenie obrázkov Kliknutím na položku Spojiť (Stitch) na hlavnej obrazovke aplikácie IJ Scan Utility zobrazíte okno Spojenie obrázkov (Image Stitch). Môžete naskenovať ľavú a pravú polovicu položky väčšej ako predlohové sklo a naskenované obrázky potom znova spojiť do jedného obrázka. Môžete skenovať položky, ktoré sú približne dvakrát také veľké ako predlohové sklo.
Samostatne sa naskenuje ľavá a pravá polovica položky, ktorá je dvakrát väčšia ako veľkosť Letter. • Celé predlohové sklo x 2 (Full Platen x 2) Samostatne sa naskenuje ľavá a pravá polovica položky, ktorá je dvakrát väčšia ako predlohové sklo. • Smer skenovania (Scan Direction) • Skenovať zľava (Scan from Left) Prvý naskenovaný obrázok sa zobrazí naľavo. • Skenovať sprava (Scan from Right) Prvý naskenovaný obrázok sa zobrazí napravo.
• Upraviť rámy orezania (Adjust cropping frames) Oblasť skenovania môžete upraviť na ukážke. Ak nevyberiete žiadnu oblasť, uloží sa obrázok s veľkosťou vybratou v časti Vyberte veľkosť výstupu (Select Output Size). Ak vyberiete niektorú oblasť, naskenuje sa a uloží iba obrázok ohraničený rámom orezania. Úprava rámov orezania v okne Spojenie obrázkov • Uložiť (Save) • Uložiť (Save) Dva naskenované obrázky sa uložia ako jeden obrázok. • Zrušiť (Cancel) Skenovanie pomocou funkcie Spojiť (Stitch) sa zruší.
• (Otočiť doľava) Umožňuje otočiť ukážku obrázka o 90 stupňov proti smeru hodinových ručičiek. • (Prevrátiť okolo zvislej osi) Umožňuje otočiť ukážku obrázka o 180 stupňov. • (Otočiť doprava) Umožňuje otočiť ukážku obrázka o 90 stupňov v smere hodinových ručičiek. • (Otvoriť príručku) Umožňuje otvoriť túto stránku. (3) Oblasť zobrazenia miniatúr • Oblasť zobrazenia miniatúr Zobrazuje miniatúry naskenovaných obrázkov. Ak sa nenaskenovala žiadna položka, táto oblasť je prázdna.
Obrázok sa naskenuje podľa smeru určeného v časti Smer skenovania (Scan Direction) a vedľa neho sa zobrazí číslo 2. • Po naskenovaní druhej položky kliknutím na tlačidlo Spustiť skenovanie obrázka 2 (Start Scanning Image 2) Zobrazia sa dva naskenované obrázky.
Skenovanie pomocou používaného aplikačného softvéru (ScanGear) Čo je to ScanGear (ovládač skenera)? Skenovanie s rozšírenými nastaveniami pomocou programu ScanGear (ovládača skenera) Spustenie programu ScanGear (ovládača skenera) Skenovanie v základnom režime Skenovanie v rozšírenom režime Skenovanie viacerých dokumentov naraz pomocou programu ScanGear (ovládača skenera) Oprava obrázkov a úprava farieb pomocou programu ScanGear (ovládača skenera) Obrazovky programu ScanGear (ovládača skenera) Umiestnenie po
Čo je to ScanGear (ovládač skenera)? ScanGear (ovládač skenera) je softvér potrebný na skenovanie dokumentov. Umožňuje vybrať veľkosť výstupu a korigovať obrázky pri skenovaní. Program ScanGear možno spustiť z aplikácie My Image Garden alebo IJ Scan Utility. Možno ho spustiť aj z iných aplikácií, ktoré sú kompatibilné so štandardným rozhraním s názvom TWAIN. (ScanGear je ovládač kompatibilný s rozhraním TWAIN.
Rozšírený režim Na karte Rozšírený režim (Advanced Mode) môžete vybrať režim farieb, rozlíšenie výstupu, jas obrázka, farebný odtieň a ďalšie nastavenia pri skenovaní.
Skenovanie s rozšírenými nastaveniami pomocou programu ScanGear (ovládača skenera) Spustenie programu ScanGear (ovládača skenera) Spustenie programu ScanGear (ovládača skenera) Skenovanie dokumentov po jednoduchých korekciách obrázkov Skenovanie v základnom režime Skenovanie dokumentov po rozšírených korekciách obrázkov a úprave jasu alebo farieb Skenovanie v rozšírenom režime Skenovanie viacerých dokumentov naraz po korekciách obrázkov a úprave farieb Skenovanie viacerých dokumentov naraz pomocou programu
Spustenie programu ScanGear (ovládača skenera) Pomocou programu ScanGear (ovládača skenera) môžete pri skenovaní korigovať obrázky a upravovať farby. Program ScanGear možno spustiť z aplikácie My Image Garden alebo inej aplikácie. Spustenie z aplikácie My Image Garden Ak chcete program ScanGear spustiť z aplikácie My Image Garden, postupujte podľa týchto krokov. 1. Spustite aplikáciu My Image Garden. Pokyny na spustenie aplikácie My Image Garden nájdete v dokumente Príručka aplikácie My Image Garden. 2.
Skenovanie v základnom režime Ak chcete skenovať bez ďalšieho nastavovania, postupujte podľa nasledujúcich krokov zobrazených na karte Základný režim (Basic Mode). Ak chcete skenovať viacero dokumentov naraz, pozrite si časť „Skenovanie viacerých dokumentov naraz pomocou programu ScanGear (ovládača skenera)“. Dôležité Nasledujúce typy dokumentov sa nemusia naskenovať správne. V takom prípade (Miniatúry) na paneli s nástrojmi prepnite na zobrazenie celého kliknutím na tlačidlo obrázka a spustite skenovanie.
Poznámka Ak chcete skenovať časopisy obsahujúce mnoho farebných fotografií, vyberte možnosť Časopis (farebný) (Magazine (Color)). 3. Kliknite na tlačidlo Ukážka (Preview). V oblasti ukážky sa zobrazí ukážka obrázka. Poznámka Farby sa upravia na základe typu dokumentu vybratého v časti Výber zdroja (Select Source). 4. Nastavte položku Cieľ (Destination). 5. Nastavte položku Veľkosť výstupu (Output Size) podľa plánovaného účelu.
Spustí sa skenovanie. Poznámka Kliknutím na tlačidlo (Informácie) otvoríte dialógové okno, v ktorom môžete skontrolovať aktuálne nastavenia skenovania (napríklad typ dokumentu). Odpoveď programu ScanGear po skenovaní možno vybrať v časti Stav dialógového okna ovládača ScanGear po skenovaní (Status of ScanGear dialog after scanning) na karte Skenovať (Scan) dialógového okna Predvoľby (Preferences).
Skenovanie v rozšírenom režime Na karte Rozšírený režim (Advanced Mode) môžete vybrať režim farieb, rozlíšenie výstupu, jas obrázka, farebný odtieň a ďalšie nastavenia pri skenovaní. Ak chcete skenovať viacero dokumentov naraz, pozrite si časť „Skenovanie viacerých dokumentov naraz pomocou programu ScanGear (ovládača skenera)“. Dôležité Nasledujúce typy dokumentov sa nemusia naskenovať správne.
Poznámka Po prepnutí na iný režim sa nezachovajú nastavenia. 3. Nastavte položku Nastavenia vstupu (Input Settings) podľa príslušného dokumentu alebo účelu. 4. Kliknite na tlačidlo Ukážka (Preview). V oblasti ukážky sa zobrazí ukážka obrázka. 5. Nastavte položku Nastavenia výstupu (Output Settings). 6. Podľa potreby upravte rám orezania (oblasť skenovania), opravte obrázok a upravte farby. Úprava rámov orezania (ScanGear) Nastavenia obrázka Tlačidlá úpravy farieb 7. Kliknite na tlačidlo Skenovať (Scan).
Odpoveď programu ScanGear po skenovaní možno vybrať v časti Stav dialógového okna ovládača ScanGear po skenovaní (Status of ScanGear dialog after scanning) na karte Skenovať (Scan) dialógového okna Predvoľby (Preferences).
Skenovanie viacerých dokumentov naraz pomocou programu ScanGear (ovládača skenera) Pomocou kariet Základný režim (Basic Mode) a Rozšírený režim (Advanced Mode) môžete naraz naskenovať dve alebo viac fotografií (malých dokumentov) umiestnených na predlohovom skle. V tejto časti sa vysvetľuje spôsob skenovania viacerých dokumentov pomocou karty Základný režim (Basic Mode). Dôležité Ak chcete naskenovať viacero dokumentov ako jeden obrázok, skenujte pri zobrazení celého obrázka.
2. Podľa dokumentu umiestneného na predlohovom skle nastavte položku Výber zdroja (Select Source). 3. Kliknite na tlačidlo Ukážka (Preview). V oblasti ukážky sa zobrazia miniatúrne ukážky obrázkov. Rámy orezania sa automaticky nastavia podľa veľkosti dokumentu. 4. Nastavte položku Cieľ (Destination). 5. Nastavte položku Veľkosť výstupu (Output Size) podľa plánovaného účelu.
6. Podľa potreby upravte rámy orezania a nastavte položku Korekcie obrázkov (Image corrections). Poznámka Jednotlivé obrázky môžete korigovať osobitne. Vyberte rám, ktorý chcete korigovať. Pri zobrazení miniatúr môžete pre každý obrázok vytvoriť len jeden rám orezania. Ak chcete na obrázku vytvoriť viacero rámov orezania, skenujte pri zobrazení celého obrázka. Skenovanie viacerých dokumentov pri zobrazení celého obrázka 7. Vyberte obrázky, ktoré chcete naskenovať.
Poznámka Po zobrazení celého obrázka sa ikona zmení na ikonu (Celý obrázok). 2. Nastavte položku Cieľ (Destination). 3. Nastavte položku Veľkosť výstupu (Output Size) podľa plánovaného účelu. Tlačidlo Obrátiť pomer strán (Invert aspect ratio) sa aktivuje v prípade, že položku Veľkosť výstupu (Output Size) nastavíte na inú hodnotu než Flexibilná (Flexible). Kliknutím na toto tlačidlo otočíte rám orezania. Ak chcete obnoviť pôvodnú orientáciu, kliknite naň znova. 4. Upravte rámy orezania.
Poznámka Odpoveď programu ScanGear po skenovaní možno vybrať v časti Stav dialógového okna ovládača ScanGear po skenovaní (Status of ScanGear dialog after scanning) na karte Skenovať (Scan) dialógového okna Predvoľby (Preferences).
Oprava obrázkov a úprava farieb pomocou programu ScanGear (ovládača skenera) Zaostrovanie nezaostrených fotografií, obmedzenie množstva prachu a škrabancov, úprava vyblednutých farieb Oprava obrázkov (maska rozostrenia, obmedzenie množstva prachu a škrabancov, korekcia vyblednutia a pod.
Oprava obrázkov (maska rozostrenia, obmedzenie množstva prachu a škrabancov, korekcia vyblednutia a pod.) Funkcie Nastavenia obrázka (Image Settings) na karte Rozšírený režim (Advanced Mode) programu ScanGear (ovládača skenera) umožňujú zlepšiť obrysy objektov, obmedziť množstvo prachu a škrabancov a korigovať vyblednuté farby pri skenovaní obrázkov. Položky nastavenia Kliknite na tlačidlo (šípka) príslušnej funkcie a z rozbaľovacej ponuky vyberte požadovanú položku.
Poznámka Podľa časti „Skenovanie v rozšírenom režime“ otvorte kartu Rozšírený režim (Advanced Mode) programu ScanGear a spustite skenovanie. Úprava jasu a farebného odtieňa obrázka Podľa typu dokumentu nastavte položku Úprava obrázkov (Image Adjustment) na hodnotu Automaticky (Auto), Fotografie (Photo), Časopis (Magazine) alebo Dokument (Document).
Obmedzenie stupňovania farieb a pásov Nastavte položku Odrastrovanie (Descreen) na hodnotu ZAP. (ON) VYP. (OFF) ZAP. (ON) Poznámka Tlačené fotografie a obrázky sa zobrazujú ako súbor jemných bodiek. Ak takéto fotografie alebo obrázky vytlačené pomocou jemných bodiek naskenujete, zobrazí sa moiré, čiže nerovnomerné stupňovanie farieb alebo pásy. Tento efekt moiré môžete obmedziť pomocou funkcie Odrastrovanie (Descreen).
Obmedzenie zrnitosti Podľa úrovne zrnitosti nastavte položku Korekcia zrnitosti (Grain Correction) na hodnotu Nízke (Low), Stredné (Medium) alebo Vysoké (High). Žiadna (None) Stredné (Medium) Korekcia tieňov, ktoré sa objavujú medzi stranami pri skenovaní otvorených brožúr Podľa úrovne tieňov nastavte položku Korekcia tieňa v oblasti väzby (Gutter Shadow Correction) na hodnotu Nízke (Low), Stredné (Medium) alebo Vysoké (High).
Úprava farieb pomocou vzorky farieb Pomocou funkcie vzorky farieb na karte Základný režim (Basic Mode) programu ScanGear (ovládača skenera) môžete zobraziť ukážku zmien farieb a reprodukovať prirodzené farby. Úprava farieb Môžete korigovať farby, ktoré časom vybledli alebo ktorých farebný odtieň sa zmenil. Zmena farebného odtieňa je jav, pri ktorom konkrétna farba ovplyvní celý obrázok v dôsledku počasia alebo okolitých výrazných farieb.
Obmedzením farebného odtieňa a zvýšením úrovne doplnkovej farby môžete reprodukovať prirodzené farby motívu. Odporúča sa vyhľadať časť obrázka, ktorá by mala byť biela, a úpravou farieb ju zmeniť na bielu. V strede sa zobrazí ukážka obrázka. Farby ukážky obrázka sa pri úprave menia. Nižšie nájdete príklad korekcie modrastého obrázka. Keďže farby Modrá (Blue) a Zelená (Green) sú príliš intenzívne, kliknutím na šípky Žltá (Yellow) a Purpurová (Magenta) ich upravte.
Úprava sýtosti a vyváženia farieb Na karte Rozšírený režim (Advanced Mode) programu ScanGear (ovládača skenera) kliknite na tlačidlo (Sýtosť/vyváženie farieb). Poznámka Kliknutím na tlačidlo Predvolené (Defaults) zrušíte všetky úpravy v aktuálnom okne. Sýtosť Upravte sýtosť (živosť) obrázka. Môžete zvýrazniť farby, ktoré časom vybledli a pod. Posúvaním jazdca v časti Sýtosť (Saturation) doľava znížite sýtosť (obrázok stmavne) a posúvaním doprava ju zvýšite (obrázok bude svetlejší).
Vyváženie farieb Upravte obrázky so zmeneným farebným odtieňom. Zmena farebného odtieňa je jav, pri ktorom konkrétna farba ovplyvní celý obrázok v dôsledku počasia alebo okolitých výrazných farieb. Posúvaním jazdca v časti Vyváženie farieb (Color Balance) doľava alebo doprava zvýraznite príslušnú farbu. Azúrová a červená Purpurová a zelená Žltá a modrá Tieto farebné páry sa vzájomne dopĺňajú (zmiešaním jednotlivých párov vznikne príslušný odtieň sivej).
Úprava jasu a kontrastu Na karte Rozšírený režim (Advanced Mode) programu ScanGear (ovládača skenera) kliknite na tlačidlo (Jas/kontrast). Poznámka Kliknutím na tlačidlo (šípka nadol) prepnete na podrobné zobrazenie. Kliknutím na tlačidlo (šípka nahor) sa vrátite k predchádzajúcemu zobrazeniu. Kliknutím na tlačidlo Predvolené (Defaults) zrušíte všetky úpravy v aktuálnom okne. Kanál Každá bodka na obrázku je zmesou červenej, zelenej a modrej farby, ktoré sú v rôznom pomere (s rôznym stupňovaním).
• Modrá (Blue) Upravte modrý kanál. Poznámka Ak je položka Režim farieb (Color Mode) nastavená na hodnotu Odtiene sivej (Grayscale), v časti Kanál (Channel) sa zobrazí iba možnosť Odtiene sivej (Grayscale). Jas Upravte jas obrázka. Posúvaním jazdca v časti Jas (Brightness) doľava obrázok stmavne a posúvaním jazdca doprava bude svetlejší. Takisto môžete zadať požadovanú hodnotu (–127 až 127). Tmavší Pôvodný obrázok Svetlejší Poznámka Ak bude obrázok príliš svetlý, môžu sa stratiť výrazné časti.
Poznámka Zvýšením kontrastu dodáte mäkkým obrázkom trojrozmerný dojem. Ak však kontrast zvýšite priveľmi, môžu sa stratiť tiene a výrazné časti.
Úprava histogramu Na karte Rozšírený režim (Advanced Mode) programu ScanGear (ovládača skenera) kliknite na tlačidlo (Histogram). Poznámka Kliknutím na tlačidlo Predvolené (Defaults) zrušíte všetky úpravy v aktuálnom okne. Kanál Každá bodka na obrázku je zmesou červenej, zelenej a modrej farby, ktoré sú v rôznom pomere (s rôznym stupňovaním). Tieto farby možno upravovať samostatne ako kanály. • Hlavný (Master) Upravte naraz červený, zelený aj modrý kanál. • Červená (Red) Upravte červený kanál.
Čítanie histogramov Môžete zobraziť histogram príslušnej oblasti pre každú položku Kanál (Channel). Čím je vrchol histogramu vyšší, tým viac údajov je umiestnených na príslušnej úrovni. (1) Svetlá oblasť (2) Tmavá oblasť (3) Celý obrázok Viac údajov je umiestnených Viac údajov je Údaje sú umiestnené na strane s výraznými časťami. pomerne rovnomerne medzi stranami s výraznými časťami a tieňmi. umiestnených na strane s tieňmi.
Obrázky, na ktorých je viac údajov umiestnených na strane s tieňmi Posúvajte jazdec bieleho bodu smerom k strane s tieňmi. Obrázky, na ktorých sú údaje umiestnené pomerne rovnomerne Posúvajte jazdec čierneho bodu smerom k strane s výraznými časťami a jazdec bieleho bodu smerom k strane s tieňmi. Posúvanie jazdca stredného bodu Posúvaním jazdca stredného bodu určte úroveň, ktorá sa má nastaviť ako stred rozsahu odtieňov.
- Bod, na ktorý kliknete pomocou kvapkadla (kvapkadlo čierneho bodu), bude najtmavší. Takisto môžete zadať požadovanú hodnotu (0 až 245). - Bod, na ktorý kliknete pomocou kvapkadla (kvapkadlo stredného bodu), bude predstavovať stred rozsahu odtieňov. Takisto môžete zadať požadovanú hodnotu (5 až 250). - Bod, na ktorý kliknete pomocou kvapkadla (kvapkadlo bieleho bodu), bude najsvetlejší. Takisto môžete zadať požadovanú hodnotu (10 až 255).
Úprava krivky odtieňov Na karte Rozšírený režim (Advanced Mode) programu ScanGear (ovládača skenera) kliknite na tlačidlo (Nastavenia krivky odtieňov). Poznámka Kliknutím na tlačidlo Predvolené (Defaults) zrušíte všetky úpravy v aktuálnom okne. Kanál Každá bodka na obrázku je zmesou červenej, zelenej a modrej farby, ktoré sú v rôznom pomere (s rôznym stupňovaním). Tieto farby možno upravovať samostatne ako kanály. • Hlavný (Master) Upravte naraz červený, zelený aj modrý kanál.
Čítanie kriviek odtieňov Pri používaní programu ScanGear je skenovanie obrázkov prostredníctvom skenera vstupom a zobrazenie na monitore výstupom. Krivka odtieňov zobrazuje vyváženie vstupu a výstupu odtieňov pre každú položku Kanál (Channel).
Vysoký kontrast (High contrast) (esovitá krivka) Výrazné časti a tiene na strane vstupu sú zvýraznené, výsledkom čoho je vysokokontrastný obrázok. Zameniť negatívny obraz za pozitívny (Reverse the negative/positive image) (klesajúca čiara) Strany vstupu a výstupu sú obrátené, výsledkom čoho je obrázok so zameneným negatívom a pozitívom. Upraviť vlastnú krivku (Edit custom curve) Presunutím jednotlivých bodov na krivke odtieňov môžete voľne upraviť jas príslušných oblastí.
Nastavenie prahovej hodnoty Jas farebných obrázkov a obrázkov s odtieňmi sivej sa vyjadruje pomocou hodnoty v rozsahu 0 až 255. Pri vytváraní čiernobielych obrázkov sa však všetky farby priradia čiernej (0) alebo bielej (255). Prahová hodnota je hraničná hodnota, ktorá určuje, či je farba čierna alebo biela. Úpravou úrovne prahovej hodnoty môžete dosiahnuť ostrejší text v dokumente alebo obmedziť presvitanie znakov v novinách.
Obrazovky programu ScanGear (ovládača skenera) Karta Základný režim Karta Rozšírený režim Nastavenia vstupu Nastavenia výstupu Nastavenia obrázka Tlačidlá úpravy farieb Dialógové okno Predvoľby Karta Skener Karta Ukážka Karta Skenovať Karta Nastavenia farieb 137
Karta Základný režim V tomto režime môžete jednoducho skenovať podľa krokov zobrazených na obrazovke. V tejto časti nájdete opis nastavení a funkcií dostupných na karte Základný režim (Basic Mode). (1) Nastavenia a ovládacie tlačidlá (2) Panel s nástrojmi (3) Oblasť ukážky Poznámka Zobrazené položky sa líšia v závislosti od typu dokumentu a zobrazenia. (1) Nastavenia a ovládacie tlačidlá • Výber zdroja (Select Source) • Fotografia (farebná) (Photo (Color)) Umožňuje skenovanie farebných fotografií.
Poznámka Po výbere typu dokumentu bude aktívna funkcia masky rozostrenia. Aktívna bude aj funkcia úprav obrázkov, ktorá upravuje obrázky na základe typu dokumentu. Ak vyberiete možnosť Časopis (farebný) (Magazine (Color)), aktívna bude funkcia odrastrovania. • Zobrazenie ukážky obrázka (Display Preview Image) • Ukážka (Preview) Umožňuje vykonať skúšobné skenovanie. Poznámka Pri prvom použití zariadenia sa automaticky spustí kalibrácia skenera. Chvíľu počkajte, kým sa nezobrazí ukážka obrázka.
• Veľkosť výstupu (Output Size) Vyberte veľkosť výstupu. Možnosti veľkosti výstupu sa líšia podľa položky vybratej v časti Cieľ (Destination). • Flexibilná (Flexible) Umožňuje voľne upraviť rámy orezania (oblasti skenovania). Pri zobrazení miniatúr Presunutím myši na príslušnú miniatúru zobrazte rám orezania. Po zobrazení rámu orezania sa naskenuje časť ohraničená týmto rámom. Ak sa nezobrazí žiadny rám orezania, jednotlivé políčka sa naskenujú samostatne.
Ak chcete pridať niektorú veľkosť, zadajte hodnoty Názov veľkosti výstupu (Output Size Name), Šírka (Width) a Výška (Height) a kliknite na tlačidlo Pridať (Add). Ak je v časti Cieľ (Destination) vybratá položka Tlač (Print), môžete v ponuke Jednotka (Unit) vybrať možnosť palce (inches) alebo mm. Ak je však v časti Cieľ (Destination) vybratá položka Zobrazenie obrázka (Image display), môžete vybrať iba možnosť pixle (pixels).
• Korekcie obrázkov (Image corrections) Umožňuje vykonávať korekcie obrázkov. Dôležité Možnosti Použiť automat. opravu dokum. (Apply Auto Document Fix) a Korigovať vyblednutie (Correct fading) sú dostupné v prípade, že na karte Nastavenia farieb (Color Settings) v dialógovom okne Predvoľby (Preferences) vyberiete položku Odporúčané (Recommended). Poznámka Dostupné funkcie sa líšia v závislosti od typu dokumentu vybratého v časti Výber zdroja (Select Source). • Použiť automat. opravu dokum.
Dôležité Toto nastavenie nie je dostupné po výbere možnosti Zhoda farieb (Color Matching) na karte Nastavenia farieb (Color Settings) v dialógovom okne Predvoľby (Preferences). • Spustenie skenovania (Perform Scan) • Skenovať (Scan) Umožňuje spustiť skenovanie. Poznámka Po spustení skenovania sa zobrazí jeho priebeh. Kliknutím na tlačidlo Zrušiť (Cancel) môžete skenovanie zrušiť. • Predvoľby... (Preferences...
• (Otočiť doprava) Umožňuje otočiť ukážku obrázka o 90 stupňov v smere hodinových ručičiek. - Výsledok sa prejaví na naskenovanom obrázku. - Pri opätovnom zobrazení ukážky sa obnoví pôvodný stav obrázka. • (Automatické orezanie) Umožňuje zobraziť a automaticky upraviť rám orezania podľa veľkosti dokumentu zobrazeného v oblasti ukážky. Ak sa v rámci rámu orezania nachádzajú oblasti, ktoré možno orezať, každým kliknutím na toto tlačidlo sa oblasť skenovania zmenší.
Po kliknutí na tlačidlo Ukážka (Preview) sa v tejto oblasti zobrazí skúšobný obrázok. Takisto tu môžete skontrolovať výsledky nastavení (korekcie obrázkov, úpravy farieb a pod.) vybratých v časti „(1) Nastavenia a ovládacie tlačidlá“. Ak sa na paneli s nástrojmi zobrazuje tlačidlo (Miniatúry) Rámy orezania sa určia podľa veľkosti dokumentu a zobrazia sa miniatúry naskenovaných obrázkov. Naskenujú sa iba obrázky so začiarknutým políčkom.
Poznámka Na zobrazenom obrázku môžete určiť rám orezania. Pri zobrazení miniatúr môžete pre každý obrázok vytvoriť len jeden rám orezania. Pri zobrazení celého obrázka môžete vytvoriť viacero rámov orezania.
Karta Rozšírený režim V tomto režime môžete vybrať rozšírené nastavenia skenovania, napríklad režim farieb, rozlíšenie výstupu, jas obrázka alebo farebný odtieň. V tejto časti nájdete opis nastavení a funkcií dostupných na karte Rozšírený režim (Advanced Mode). (1) Nastavenia a ovládacie tlačidlá (2) Panel s nástrojmi (3) Oblasť ukážky Poznámka Zobrazené položky sa líšia v závislosti od typu dokumentu a zobrazenia.
Zadajte text v poli Názov nastavenia (Setting Name) a kliknite na tlačidlo Pridať (Add). Názov sa zobrazí v časti Zoznam obľúbených nastavení (Favorite Settings List). Po kliknutí na tlačidlo Uložiť (Save) sa položka zobrazí v zozname Obľúbené nastavenia (Favorite Settings) a možno ju vybrať spoločne s vopred definovanými položkami. Ak chcete niektorú položku odstrániť, vyberte ju v zozname Zoznam obľúbených nastavení (Favorite Settings List) a kliknite na tlačidlo Odstrániť (Delete).
Pri zobrazení miniatúr Ak je pri zobrazení miniatúr zobrazených viacero obrázkov, kliknutím na toto tlačidlo priblížite vybratý rám. Ak chcete zobraziť predchádzajúci alebo nasledujúci rám, kliknite na tlačidlo (O snímku dopredu) v dolnej časti obrazovky. Poznámka Obrázok môžete priblížiť aj tak, že dvakrát kliknete na rám. Ak na rám znova dvakrát kliknete, obnoví sa zobrazenie bez priblíženia.
Poznámka Po spustení skenovania sa zobrazí jeho priebeh. Kliknutím na tlačidlo Zrušiť (Cancel) môžete skenovanie zrušiť. Po dokončení skenovania sa môže zobraziť dialógové okno s výzvou na výber ďalších krokov. Postupujte podľa výzvy. Podrobné informácie nájdete v odseku Stav dialógového okna ovládača ScanGear po skenovaní (Status of ScanGear dialog after scanning) v časti „Karta Skenovať“ (dialógové okno Predvoľby (Preferences)).
• (Orezať) Umožňuje určiť oblasť skenovania pomocou myši. • (Posunúť obrázok) Ak sa obrázok zväčšený v oblasti ukážky nezmestí na obrazovku, môžete ho pomocou myši presúvať, kým sa nezobrazí požadovaná časť. Obrázok môžete posúvať aj pomocou posúvačov. • (Zväčšiť/zmenšiť) Umožňuje priblížiť oblasť ukážky kliknutím na obrázok. Ak chcete obrázok vzdialiť, kliknite naň pravým tlačidlom myši. • (Otočiť doľava) Umožňuje otočiť ukážku obrázka o 90 stupňov proti smeru hodinových ručičiek.
Rámy orezania sa zmenia na hrubé prerušované čiary a na všetky z nich sa použijú príslušné nastavenia. • (Odstrániť rám orezania) Umožňuje odstrániť vybratý rám orezania. • (Informácie) Umožňuje zobraziť verziu programu ScanGear a aktuálne nastavenia skenovania (typ dokumentu a pod.). • (Otvoriť príručku) Umožňuje otvoriť túto stránku. (3) Oblasť ukážky • Oblasť ukážky Po kliknutí na tlačidlo Ukážka (Preview) sa v tejto oblasti zobrazí skúšobný obrázok.
Vybratý rám (tenký modrý obrys): nastavenia sa použijú na aktívny rám aj na vybraté rámy naraz. Viacero obrázkov môžete vybrať tak, že podržíte kláves Ctrl a kliknete na požadované obrázky. Nevybraté (bez obrysu): nastavenia sa nepoužijú. Ak sa na paneli s nástrojmi zobrazuje tlačidlo (Celý obrázok) Položky umiestnené na predlohovom skle sa naskenujú a zobrazia ako jeden obrázok. Naskenujú sa všetky časti ohraničené rámami orezania. Poznámka Na zobrazenom obrázku môžete určiť rám orezania.
Nastavenia vstupu V časti Nastavenia vstupu (Input Settings) môžete nastaviť nasledujúce položky: • Výber zdroja (Select Source) Zobrazí sa typ dokumentu, ktorý sa naskenuje. • Veľkosť papiera (Paper Size) Vyberte veľkosť dokumentu, ktorý chcete naskenovať. Toto nastavenie je dostupné iba pri zobrazení celého obrázka. Podľa vybratej veľkosti sa zmení aj veľkosť oblasti ukážky. Dôležité Niektoré aplikácie môžu prijať len obmedzené množstvo skenovaných údajov. K dispozícii je nasledujúci rozsah skenovania.
• Farebne (Color) Tento režim vyberte v prípade, ak chcete skenovať farebné dokumenty alebo vytvárať farebné obrázky. V tomto režime sa obrázok vytvorí pomocou 256 úrovní (8 bitov) červenej (R), zelenej (G) a modrej (B) farby. • Odtiene sivej (Grayscale) Tento režim vyberte v prípade, ak chcete skenovať čiernobiele fotografie alebo vytvárať čiernobiele obrázky. V tomto režime sa obrázok vytvorí pomocou 256 úrovní (8 bitov) čiernej a bielej farby.
Nastavenia výstupu V časti Nastavenia výstupu (Output Settings) môžete nastaviť nasledujúce položky: • Rozlíšenie výstupu (Output Resolution) Vyberte rozlíšenie skenovania. Čím je hodnota rozlíšenia vyššia, tým je obrázok detailnejší. Vyberte príslušné rozlíšenie z možností zobrazených po kliknutí na tlačidlo alebo zadajte príslušnú hodnotu v rozsahu 25 až 19 200 dpi (s krokom 1 dpi). Podrobné informácie nájdete v časti „Rozlíšenie“ pre svoj model dostupnej z obrazovky Domov dokumentu Príručka online.
Pri zobrazení celého obrázka Ak sa nezobrazí žiadny rám orezania, naskenuje sa celá oblasť ukážky. Po zobrazení rámu orezania sa naskenuje časť ohraničená týmto rámom. Poznámka Ak chcete naskenovaný obrázok zväčšiť alebo zmenšiť, zadajte hodnoty v poliach (šírka) a (výška) v časti Nastavenia výstupu (Output Settings) alebo zadajte príslušnú hodnotu (s krokom 1 %) v poli %.
Zoznam veľkostí výstupu (Output Size List). Kliknutím na tlačidlo Uložiť (Save) uložte položky uvedené v časti Zoznam veľkostí výstupu (Output Size List). Odstrániť Ak chcete niektorú položku odstrániť, vyberte ju v zozname Zoznam veľkostí výstupu (Output Size List) a kliknite na tlačidlo Odstrániť (Delete). Kliknutím na tlačidlo Uložiť (Save) uložte položky uvedené v časti Zoznam veľkostí výstupu (Output Size List).
Nastavenia obrázka Dôležité Tieto funkcie nepoužívajte na obrázky bez zrnitosti, prachu, škrabancov alebo vyblednutých farieb. Mohli by ste negatívne ovplyvniť ich farebný odtieň. Výsledky korekcie obrázkov sa nemusia prejaviť na ukážke obrázka. Poznámka Nastavenia, ktoré možno vybrať, závisia od nastavení v časti Režim farieb (Color Mode). Ak použijete nastavenia v časti Nastavenia obrázka (Image Settings), skenovanie môže trvať dlhšie než zvyčajne.
Použije sa úprava obrázkov vhodná pre fotografie. • Časopis (Magazine) Použije sa úprava obrázkov vhodná pre časopisy. • Dokument (Document) Použije sa úprava obrázkov vhodná pre textové dokumenty. Dôležité Nastavenie Úprava obrázkov (Image Adjustment) môžete vybrať po zobrazení ukážky. Toto nastavenie môžete vybrať po výbere možnosti Odporúčané (Recommended) na karte Nastavenia farieb (Color Settings) v dialógovom okne Predvoľby (Preferences).
• VYP. (OFF) Maska rozostrenia sa nepoužije. • ZAP. (ON) Slúži na zvýraznenie obrysu objektov a zostrenie snímky. Odporúča sa, aby ste za normálnych okolností vybrali toto nastavenie. • Odrastrovanie (Descreen) Tlačené fotografie a obrázky sa zobrazujú ako súbor jemných bodiek. Ak takéto fotografie alebo obrázky vytlačené pomocou jemných bodiek naskenujete, zobrazí sa moiré, čiže nerovnomerné stupňovanie farieb alebo pásy. Tento efekt moiré môžete obmedziť pomocou funkcie Odrastrovanie (Descreen). • VYP.
Dôležité Pri niektorých typoch fotografií nemusí byť táto funkcia účinná. Poznámka Pri skenovaní tlačených materiálov sa odporúča vybrať možnosť Žiadna (None). • Korekcia vyblednutia (Fading Correction) Pomocou tejto funkcie môžete vykonať korekciu fotografií, ktoré časom vybledli alebo zmenili farebný odtieň. Zmena farebného odtieňa je jav, pri ktorom konkrétna farba ovplyvní celý obrázok v dôsledku počasia alebo okolitých výrazných farieb. • Žiadna (None) Korekcia vyblednutia sa nepoužije.
Odporúča sa, aby ste za normálnych okolností vybrali toto nastavenie. • Vysoké (High) Túto možnosť vyberte v prípade, ak je fotografia veľmi zrnitá. Môže sa tým ovplyvniť stupňovanie farieb a ostrosť obrázka. Dôležité Ak je oblasť skenovania príliš malá, korekcia sa nemusí použiť správne. • Korekcia tieňa v oblasti väzby (Gutter Shadow Correction) Pomocou tejto funkcie môžete korigovať tiene, ktoré sa objavujú medzi stranami pri skenovaní otvorených brožúr.
Pri niektorých dokumentoch sa tiene nemusia opraviť správne. Ak pozadie strany nie je biele, tiene sa nemusia rozpoznať správne alebo vôbec. Pri skenovaní tlačte na väzbu rovnakou silou ako pri zobrazení ukážky skenovaného obrázka. Ak časť s väzbou nie je rovná, nevykoná sa správna korekcia tieňa. Spôsob umiestnenia dokumentu závisí od modelu zariadenia a skenovaného dokumentu.
Tlačidlá úpravy farieb Tlačidlá úpravy farieb umožňujú vykonávať jemné korekcie jasu a farebného odtieňa obrázka vrátane úprav celkového jasu alebo kontrastu obrázka a úprav hodnôt výrazných častí a tieňov (histogram) alebo vyváženia (krivka odtieňov). Dôležité Tlačidlá úpravy farieb nie sú dostupné po výbere možnosti Zhoda farieb (Color Matching) na karte Nastavenia farieb (Color Settings) v dialógovom okne Predvoľby (Preferences).
Upravte jas a kontrast obrázka. Ak je obrázok príliš tmavý, svetlý alebo nevýrazný v dôsledku nedostatočného kontrastu, môžete upraviť úrovne jasu a kontrastu. Úprava jasu a kontrastu • (Histogram) Histogram umožňuje zobraziť koncentráciu údajov pri jednotlivých úrovniach jasu snímky. Môžete určiť najjasnejšiu a najtmavšiu úroveň snímky (výrazné časti a tiene), znížiť tieto úrovne a zvýšiť strednú hodnotu rozsahu odtieňov na snímke.
Nastavte hraničnú (prahovú) hodnotu rozdelenia čiernej a bielej farby. Úpravou úrovne prahovej hodnoty môžete dosiahnuť ostrejší text v dokumente alebo obmedziť presvitanie znakov v novinách. Nastavenie prahovej hodnoty • Vlastné (Custom) Môžete zadať názov a uložiť skupinu nastavení krivky odtieňov a prahovej hodnoty pre tlačidlá úpravy farieb. V rozbaľovacej ponuke vyberte položku Pridať/odstrániť... (Add/Delete...
Dialógové okno Predvoľby Kliknutím na tlačidlo Predvoľby... (Preferences...) na obrazovke programu ScanGear (ovládača skenera) otvoríte dialógové okno Predvoľby (Preferences). Na kartách Skener (Scanner), Ukážka (Preview), Skenovať (Scan) a Nastavenia farieb (Color Settings) dialógového okna Predvoľby (Preferences) môžete vybrať rozšírené nastavenia funkcií programu ScanGear.
Karta Skener Na karte Skener (Scanner) môžete vybrať nasledujúce nastavenia. • Nastavenia automatického napájania (Auto Power Settings) Zariadenie môžete nastaviť tak, aby sa automaticky zapínalo alebo vypínalo. Kliknutím na tlačidlo Nastavenia... (Settings...) zobrazte dialógové okno Nastavenia automatického napájania (Auto Power Settings). Poznámka Ak je zariadenie vypnuté alebo ak je zakázaná obojsmerná komunikácia, môže sa zobraziť hlásenie, pretože počítač nedokáže zistiť stav zariadenia.
Funkcia tichého režimu umožňuje znížiť prevádzkový hluk zariadenia. Tento režim použite v prípade, že chcete znížiť prevádzkový hluk, napríklad pri skenovaní alebo tlači v noci. Kliknutím na tlačidlo Nastavenia... (Settings...) nastavte tichý režim. Poznámka Tichý režim môžete nastaviť na ovládacom paneli zariadenia, v ovládači tlačiarne alebo v programe ScanGear.
• Nastavenia zvuku (Sound Settings) Zariadenie môžete nastaviť tak, aby počas skenovania alebo po jeho skončení prehrávalo hudbu. Začiarknite políčko Prehrávať hudbu počas skenovania (Play Music During Scanning) alebo Prehrať zvuk po dokončení skenovania (Play Sound When Scanning is Completed) a kliknutím na tlačidlo Prehľadávať... (Browse...) vyberte príslušný zvukový súbor. Môžete vybrať nasledujúce súbory. - Súbor MIDI (*.mid, *.rmi, *.midi) - Zvukový súbor (*.wav, *.aif, *.aiff) - Súbor MP3 (*.
Karta Ukážka Na karte Ukážka (Preview) môžete vybrať nasledujúce nastavenia. • Ukážka pri spustení ovládača ScanGear (Preview at Start of ScanGear) Vyberte možnosti ukážky po spustení programu ScanGear (ovládača skenera). • Zobraziť ukážku automaticky (Automatically Execute Preview) Pri spustení programu ScanGear sa automaticky zobrazí ukážka. • Zobraziť uloženú ukážku obrázka (Display Saved Preview Image) Zobrazí sa predtým zobrazená ukážka obrázka.
• Zobraziť posledný rám na ukážkach obrázkov (Display the Last Frame on Previewed Images) Po zobrazení ukážky sa zobrazí rám orezania s rovnakou veľkosťou ako naposledy použitý rám orezania. • Žiadna (None) Po zobrazení ukážky sa nezobrazí žiadny rám orezania. • Veľkosť orezania pri zobrazení miniatúr (Cropping Size for Thumbnail View) Vyberte veľkosť orezania miniatúr naskenovaných dokumentov. • Väčšia (Larger) Zobrazí sa 105 % (na šírku aj na výšku) oblasti zobrazenej pri štandardnej veľkosti.
Karta Skenovať Na karte Skenovať (Scan) môžete vybrať nasledujúce nastavenia. • Stav dialógového okna ovládača ScanGear po skenovaní (Status of ScanGear dialog after scanning) Vyberte možnosti programu ScanGear (ovládača skenera) po naskenovaní obrázkov. • Zavrieť ovládač ScanGear automaticky (Close ScanGear automatically) Ak vyberiete túto možnosť, po dokončení skenovania sa vrátite do pôvodnej aplikácie.
Poznámka Aj keď je vybratá možnosť Nezatvárať ovládač ScanGear automaticky (Do not close ScanGear automatically) alebo Zobraziť dialógové okno na výber ďalšej akcie (Display the dialog to select next action), niektoré aplikácie ju nemusia podporovať.
Pre každý obrázok môžete vytvoriť len jeden rám orezania. Pri zobrazení celého obrázka Kliknutím a potiahnutím myšou mimo existujúceho rámu orezania vytvoríte v oblasti ukážky nový rám orezania. Nový rám orezania sa stane aktívnym rámom orezania a starý rám orezania sa stane nevybratým rámom orezania. Môžete vytvoriť viacero rámov orezania a na každý z nich použiť iné nastavenia skenovania. Viacero rámov orezania môžete vybrať aj tak, že podržíte kláves Ctrl a kliknete na požadované rámy.
Odstraňovanie rámov orezania Pri zobrazení miniatúr Ak chcete rám orezania odstrániť, kliknite na oblasť mimo rámu orezania na obrázku. Pri zobrazení celého obrázka Ak chcete rám orezania odstrániť, vyberte ho a kliknite na položku (Odstrániť rám orezania) na paneli s nástrojmi. Prípadne stlačte kláves Delete. Ak existuje viacero rámov orezania, všetky vybraté rámy orezania (aktívny rám orezania a vybraté rámy orezania) sa odstránia naraz.
Všeobecné poznámky (ovládač skenera) Na program ScanGear (ovládač skenera) sa vzťahujú nasledujúce obmedzenia. Pri používaní programu na ne pamätajte. Obmedzenia ovládača skenera • Pri používaní systému súborov NTFS sa nemusí vyvolať zdroj údajov TWAIN. To preto, že z bezpečnostných dôvodov sa modul TWAIN nemôže zapísať do priečinka winnt. Požiadajte o pomoc správcu počítača. • Niektoré počítače (vrátane prenosných počítačov) pripojené k zariadeniu sa nemusia správne prepnúť z pohotovostného režimu.
• Obrázky nemožno skenovať pomocou aplikácie Media Center dodávanej so systémom Windows XP Media Center Edition 2005. Skenujte pomocou iných aplikácií, napríklad použitím pomôcky IJ Scan Utility. • V niektorých aplikáciách sa nemusí zobrazovať používateľské rozhranie TWAIN. V takom prípade si pozrite príručku k aplikácii a zmeňte nastavenia podľa potreby. • Niektoré aplikácie nepodporujú nepretržité skenovanie viacerých dokumentov.
Užitočné informácie o skenovaní Úprava rámov orezania v okne Spojenie obrázkov Rozlíšenie Formáty údajov Farebná zhoda 186
Úprava rámov orezania v okne Spojenie obrázkov Orezanie je operácia, pri ktorej na obrázku vyberiete oblasť, ktorú chcete pri skenovaní zachovať. Zvyšná časť sa odstráni. V okne Spojenie obrázkov (Image Stitch) môžete nastaviť rám orezania na obrázku, ktorý sa zobrazuje v oblasti ukážky. Poznámka Informácie o úprave rámov orezania pomocou aplikácie ScanGear (ovládača skenera) nájdete v časti „Úprava rámov orezania (ScanGear)“ pre svoj model z obrazovky Domov dokumentu Príručka online.
Rozlíšenie Údaje naskenovaného obrázka predstavujú súbor bodiek s informáciami o jase a farbe. Hustota týchto bodiek sa nazýva rozlíšenie a toto rozlíšenie určuje množstvo detailov na obrázku. Jednotkou rozlíšenia sú body na palec (DPI). DPI predstavuje počet bodov na palec (2,5 cm). Čím je hodnota rozlíšenia vyššia, tým je obrázok detailnejší. Čím je hodnota rozlíšenia nižšia, tým je menej detailnejší. Spôsob nastavenia rozlíšenia Rozlíšenie môžete nastaviť na nasledujúcich obrazovkách.
Priloženie k e-mailu Farebne, odtiene sivej alebo čiernobielo 150 dpi Skenovanie textu pomocou funkcie OCR Farebne alebo odtiene sivej 300 dpi Dôležité Ak rozlíšenie zdvojnásobíte, veľkosť údajov skenovaného obrázka sa zväčší štvornásobne. Ak je súbor príliš veľký, značne sa zníži rýchlosť spracovania a vyskytnú sa nepríjemnosti, napríklad nedostatok pamäte. Nastavte minimálne požadované rozlíšenie podľa plánovaného použitia obrázka.
Formáty údajov Pri ukladaní naskenovaných obrázkov môžete vybrať formát údajov. Mali by ste určiť najvhodnejší formát údajov podľa plánovaného spôsobu použitia obrázka v príslušnej aplikácii. Dostupné formáty údajov sa líšia v závislosti od aplikácie a operačného systému (Windows alebo Mac OS). Charakteristiky jednotlivých formátov obrazových údajov nájdete nižšie. PNG (bežná prípona súboru: .png) Formát údajov, ktorý sa často používa na webových stránkach.
Možno ho používať v rôznych počítačoch a operačných systémoch a možno doň vložiť aj typy písma. Takéto súbory si môžu vymieňať ľudia v rôznych prostrediach bez toho, aby si všimli rozdiely.
Farebná zhoda „Zhoda farieb“ predstavuje vykonávanie takých úprav, aby sa zhodovali farebné odtiene pôvodnej položky, odtiene na monitore a odtiene farebného výtlačku. V skeneri alebo tlačiarni sa farebné odtiene upravujú tak, ako je znázornené nižšie.
Ponuka a obrazovka nastavení aplikácie IJ Network Scanner Selector EX Aplikácia IJ Network Scanner Selector EX umožňuje vybrať skenery alebo tlačiarne, ktoré chcete prostredníctvom siete používať na skenovanie alebo tlač pomocou počítača alebo ovládacieho panela. Po inštalácii sa v oblasti oznámení na pracovnej ploche zobrazí ikona aplikácie IJ Network Scanner Selector EX.
Dôležité Ak používate model, ktorý nedokáže skenovať prostredníctvom siete pomocou ovládacieho panela, aj napriek povoleniu tohto nastavenia nemôžete ovládací panel používať na skenovanie. • Nastavenia... (Settings...) Zobrazí sa obrazovka nastavení skenovania z počítača. Môžete vybrať model, ktorý chcete používať. • Informácie (About) Umožňuje zobraziť informácie o verzii. • Skončiť (Exit) Umožňuje ukončiť aplikáciu IJ Network Scanner Selector EX.
Obrazovka nastavení skenovania pomocou ovládacieho panela Kliknutím na položku Nastavenia skenovania z ovládacieho panela (Scan-fromOperation-Panel Settings) na obrazovke nastavení skenovania z počítača zobrazíte obrazovku nastavení skenovania pomocou ovládacieho panela. • Skenery (Scanners) Zobrazia sa adresy MAC skenerov alebo tlačiarní, ktoré možno používať prostredníctvom siete. Naraz môžete celkovo vybrať až tri skenery a tlačiarne.
Odinštalovanie aplikácie IJ Network Scanner Selector EX Podľa nasledujúceho postupu odinštalujete aplikáciu IJ Network Scanner Selector EX z počítača. Dôležité Po odinštalovaní aplikácie IJ Network Scanner Selector EX nemôžete skenovať prostredníctvom siete. Použitím správcovských oprávnení sa prihláste ako používateľ. 1. Odinštalujte aplikáciu IJ Network Scanner Selector EX. • V systéme Windows 8: 1.
2. Zo zoznamu programov vyberte aplikáciu Canon IJ Network Scanner Selector EX a kliknite na tlačidlo Zmeniť alebo odstrániť (Change/ Remove). 2. Po zobrazení potvrdzujúcej správy kliknite na tlačidlo Áno (Yes). 3. Po dokončení odinštalovania kliknite na tlačidlo OK. Poznámka Keď sa zobrazí hlásenie vyžadujúce reštartovanie počítača, kliknutím na tlačidlo OK reštartujte počítač.
Ďalšie skenovacie postupy Skenovanie pomocou ovládača WIA Skenovanie pomocou ovládacieho panela (iba pre Windows XP) 198
Skenovanie pomocou ovládača WIA Položku môžete naskenovať z aplikácie kompatibilnej s ovládačom WIA (Windows Image Acquisition). WIA je model ovládača implementovaný v systéme Windows XP alebo novších. Umožňuje skenovať položky bez použitia aplikácie. Postup sa líši v závislosti od príslušnej aplikácie. Nasledujúce postupy sú len príklady. Podrobné informácie nájdete v príručke k aplikácii. Dôležité V systéme Windows XP nemôžete skenovať pomocou ovládača WIA, ak používate sieťové pripojenie.
V prípade pripojenia USB: Canon XXX series (kde „XXX“ je názov modelu) V prípade sieťového pripojenia: XXX series_Adresa MAC (XXX series_MAC address) (kde „XXX“ je názov modelu) 3. Zadajte nastavenia. • Skenery (Scanners) Zobrazí sa názov aktuálne nastaveného produktu. Ak chcete zmeniť skener, kliknite na tlačidlo Zmeniť... (Change...) a vyberte produkt, ktorý chcete používať. • Profil (Profile) Vyberte možnosť Fotografie (predvolené) (Photo (Default)) alebo Dokumenty (Documents) podľa skenovanej položky.
Posunutím jazdca upravte kontrast. Posúvaním doľava sa kontrast obrázka zníži, vďaka čomu bude obrázok mäkší. Posúvaním doprava sa kontrast obrázka zvýši, vďaka čomu bude obrázok ostrejší. Takisto môžete zadať požadovanú hodnotu (– 100 až 100). • Obrázky zobrazovať v ukážke alebo skenovať ako samostatné súbory (Preview or scan images as separate files) Začiarknutím tohto políčka môžete zobraziť ukážku viacerých obrázkov alebo ich naskenovať ako samostatné súbory.
Poznámka Pri používaní skenera alebo tlačiarne so sieťovým pripojením sa možnosti pre typ obrázka môžu líšiť od možností zobrazených pre pripojenie USB. Ak chcete skenovať použitím hodnôt, ktoré ste predtým nastavili v časti Úprava kvality skenovaného obrázka (Adjust the quality of the scanned picture), vyberte položku Vlastné nastavenie (Custom Settings). 4. Kliknite na položku Úprava kvality skenovaného obrázka (Adjust the quality of the scanned picture) a nastavte požadované predvoľby.
6. Kliknite na tlačidlo Skenovať (Scan). Po dokončení skenovania sa naskenovaný obrázok zobrazí v aplikácii.
Skenovanie pomocou ovládacieho panela (iba pre Windows XP) Obrázky môžete skenovať pomocou Ovládacieho panela systému Windows XP použitím ovládača WIA. Dôležité Pri používaní skenera alebo tlačiarne so sieťovým pripojením nemôžete na skenovanie používať ovládač WIA. 1. V ponuke Štart (Start) vyberte položku Ovládací panel (Control Panel). 2.
5. Kliknutím na tlačidlo Vlastné nastavenie (Custom settings) nastavte požadované predvoľby. • Jas (Brightness) Posunutím jazdca upravte jas. Posúvaním doľava bude obrázok tmavší a posúvaním doprava bude svetlejší. Takisto môžete zadať požadovanú hodnotu (–127 až 127). • Kontrast (Contrast) Posunutím jazdca upravte kontrast. Posúvaním doľava sa kontrast obrázka zníži, vďaka čomu bude obrázok mäkší. Posúvaním doprava sa kontrast obrázka zvýši, vďaka čomu bude obrázok ostrejší.
Umiestnenie položiek (pri skenovaní z počítača) Zistite, ako treba umiestniť položky na predlohové sklo skenera alebo tlačiarne. Položky musíte umiestniť správne podľa typu skenovanej položky. V opačnom prípade sa položky nemusia správne naskenovať. Dôležité Na kryt dokumentov neklaďte predmety. Po otvorení krytu dokumentov môžu predmety spadnúť do skenera alebo tlačiarne a spôsobiť poruchu. Pri skenovaní zatvorte kryt dokumentov.
Dôležité Dôležité Veľké položky (napríklad fotografie veľkosti A4) presahujúce cez okraje alebo šípku (značku zarovnania) predlohového skla možno uložiť ako súbory PDF. Ak chcete ukladať v inom formáte než PDF, pred skenovaním vyberte formát údajov. Umiestnenie viacerých položiek Medzi okrajmi predlohového skla (uhlopriečne šrafovanou oblasťou) a položkami, ako aj jednotlivými položkami nechajte priestor aspoň 1 cm (0,4 palca). Časti umiestnené na uhlopriečne šrafovanej oblasti nemožno naskenovať.
Poloha šikmých položiek (10 alebo menej stupňov) sa koriguje automaticky.
Skenovanie z ovládacieho panela zariadenia Odosielanie naskenovaných údajov do počítača pomocou ovládacieho panela zariadenia Základné Pripojenie naskenovaných údajov k e-mailu pomocou ovládacieho panela zariadenia Ukladanie naskenovaných údajov na pamäťovú kartu pomocou ovládacieho panela zariadenia Odstraňovanie naskenovaných údajov z pamäťovej karty Položky nastavenia na ovládacom paneli zariadenia Nastavenia skenovania v sieti Výber odpovede na príkazy z ovládacieho panela použitím aplikácie IJ Scan Uti
Odosielanie naskenovaných údajov do počítača pomocou ovládacieho panela zariadenia Naskenované údaje môžete odoslať do počítača pomocou ovládacieho panela zariadenia. Pred odoslaním naskenovaných údajov do počítača skontrolujte, či sú splnené nasledujúce podmienky: • Sú nainštalované ovládače MP Drivers. Ak nie sú nainštalované ovládače MP Drivers, nainštalujte ovládače MP Drivers z Inštalačného disku alebo z našej webovej lokality. • Zariadenie je správne pripojené k počítaču.
Ak údaje odosielate do počítača pripojeného k sieti: Zobrazí sa obrazovka na výber umiestnenia uložených údajov. Poznámka • Ak sa na dotykovej obrazovke zobrazí pohotovostná obrazovka skenovania určená na odoslanie údajov do počítača pripojeného pomocou rozhrania USB, ťuknutím na ikonu zobrazte obrazovku na výber umiestnenia uložených údajov. Podľa nasledujúceho postupu vyberte počítač, do ktorého sa odošlú naskenované údaje. 1. Ťuknite na položku Počítač (PC). 2.
A. Ťuknutím na túto položku môžete vybrať typ dokumentu. Poznámka • Ak odošlete naskenované údaje do počítača vyhľadaného pomocou protokolu WSD, nemôžete vybrať typ dokumentu. Automatické sken. (Auto scan) Táto položka je dostupná iba po pripojení zariadenia k počítaču pomocou kábla USB. Zariadenie automaticky zistí typ originálov a obrázok odošle s optimalizovanou veľkosťou a rozlíšením a v optimalizovanom formáte údajov. Dôležité • Možnosť Automatické sken.
C. Ťuknutím na túto položku zobrazíte možnosti vloženia originálu. D. Ťuknutím na túto položku zobrazíte obrazovku na výber umiestnenia. 4. Umiestnite originál na ploché predlohové sklo. 5. Dotknutím sa tlačidla Farebne (Color) nastavte farebné skenovanie, dotknutím sa tlačidla Čiernobielo (Black) čiernobiele skenovanie. Poznámka • Keď odosielate naskenované údaje do počítača pomocou protokolu WSD, dotknite sa tlačidla Farebne (Color).
• Ak používate systém Windows XP: Po prvom dotknutí sa tlačidla Farebne (Color) alebo Čiernobielo (Black) sa môže zobraziť obrazovka výberu programu. V takom prípade vyberte program Canon IJ Scan Utility ako aplikačný softvér, ktorý chcete použiť. Vyberte možnosť Pre túto akciu vždy použiť tento program (Always use this program for this action) a kliknite na tlačidlo OK. Odteraz sa bude program Canon IJ Scan Utility spúšťať automaticky.
Pripojenie naskenovaných údajov k e-mailu pomocou ovládacieho panela zariadenia Naskenované údaje môžete priložiť k e-mailu pomocou ovládacieho panela zariadenia. Pred pripojením naskenovaných údajov k e-mailu skontrolujte, či sú splnené nasledujúce podmienky: • Sú nainštalované ovládače MP Drivers. Ak nie sú nainštalované ovládače MP Drivers, nainštalujte ovládače MP Drivers z Inštalačného disku alebo z našej webovej lokality. • Zariadenie je správne pripojené k počítaču.
3. Ťuknite na položku Pripojiť k e-mailu (Attach to E-mail). 4. Ťuknite na počítač, do ktorého sa majú odoslať naskenované údaje. Ak je počítač pripojený prostredníctvom rozhrania USB, ťuknite na položku Lokálny (USB) (Local (USB)). Ak je počítač pripojený k sieti, ťuknite na počítač, do ktorého sa odošlú naskenované údaje. Zobrazí sa pohotovostná obrazovka skenovania. 5. V prípade potreby zadajte nastavenia. A. Ťuknutím na túto položku môžete vybrať typ dokumentu.
• Ak na obrazovke nastavenia skenovania vyberiete v položke Formát (Format) možnosť JPEG: Zariadenie spustí skenovanie, naskenované údaje sa odošlú do počítača a priložia k e-mailu. • Ak na obrazovke nastavenia skenovania vyberiete v položke Formát (Format) možnosť PDF alebo Kompaktný PDF (Compact PDF): Po dokončení skenovania sa zobrazí obrazovka s potvrdením, či chcete pokračovať v skenovaní. Ak chcete pokračovať v skenovaní, položte originál na ploché predlohové sklo a spustite skenovanie.
Ukladanie naskenovaných údajov na pamäťovú kartu pomocou ovládacieho panela zariadenia Naskenované údaje môžete pomocou ovládacieho panela uložiť na pamäťovú kartu. Dôležité • V nasledujúcich prípadoch nevyberajte pamäťovú kartu zo zariadenia: • počas skenovania, • pred uložením naskenovaných údajov. • Z bezpečnostných dôvodov odporúčame naskenované údaje uložené na pamäťovej karte pravidelne zálohovať na iné médium, aby ste sa vyhli neočakávaným stratám.
Po dotknutí sa tlačidla DOMOV (HOME) sa zobrazí domovská obrazovka. 4. Ťuknite na položku Pamäťová karta (Memory card). 5. Ťuknite na položku Uložiť na pamäťovú kartu (Save to memory card). Zobrazí sa pohotovostná obrazovka skenovania. 6. Podľa potreby upravte nastavenia. A. Ťuknutím na túto položku môžete vybrať typ dokumentu. Dokument (Document) Originál na plochom predlohovom skle sa naskenuje ako údaje dokumentu s použitím nastavení zadaných v ponuke Nastav. sken. (Scan settings).
A. Zobrazí sa obrazovka s ukážkou naskenovaných údajov. Obrazovka sa zobrazí, keď na obrazovke nastavenia skenovania vyberiete možnosť PDF alebo Kompaktný PDF (Compact PDF) pre položku Formát (Format). B. Ťuknutím na túto položku môžete otočiť obrazovku s ukážkou. C. Ťuknutím na toto tlačidlo uložíte originál na pamäťovú kartu. D. Ťuknutím na toto tlačidlo môžete znova naskenovať originál.
• Názov priečinka: (prípona súboru: JPG): CANON_SC\IMAGE\0001 • Názov súboru: poradové čísla začínajúce od SCN_0001. • Dátum súboru: 01/01/2013 • Import naskenovaných údajov uložených na pamäťovej karte do počítača Naskenované údaje uložené na pamäťovej karte naimportujte do počítača až po vykonaní niektorej z operácií uvedených nižšie: -vypnutie a opätovné zapnutie zariadenia, -vybratie a následné vloženie pamäťovej karty do zásuvky na kartu.
Odstraňovanie naskenovaných údajov z pamäťovej karty Naskenované údaje môžete pomocou ovládacieho panela odstrániť z pamäťovej karty. 1. Skontrolujte, či je zariadenie zapnuté. 2. Rýchlo pohnite prstom po domovskej obrazovke a ťuknite na položku Skenovať (Scan). Používanie ovládacieho panela Zobrazí sa obrazovka na výber umiestnenia uložených údajov.
A. Rýchlym pohybom môžete zobraziť názov súboru a potom ťuknutím odstrániť údaje. Po výbere formátu údajov PDF sa na dotykovej obrazovke zobrazí len prvá strana údajov vo formáte PDF. B. Ťuknutím na túto ikonu zobrazíte obrazovku s ukážkou. Po výbere formátu údajov PDF sa na dotykovej obrazovke zobrazí len prvá strana údajov vo formáte PDF. C. Ťuknutím na toto tlačidlo môžete zmeniť typ súborov zobrazených na dotykovej obrazovke. D. Rýchlym pohybom údaje zobrazíte a potom ich ťuknutím môžete odstrániť. E.
Položky nastavenia na ovládacom paneli zariadenia Môžete zmeniť nastavenia skenovania, napríklad veľkosť skenovania, rozlíšenie alebo formát údajov. Keď sa zobrazí pohotovostná obrazovka skenovania, ťuknite na tlačidlo Nastavenia (Settings) a vyberte príslušnú položku nastavenia. Rýchlym pohybom zobrazte položky nastavenia a potom ťuknutím na položku nastavenia zobrazte nastavenia. Ťuknutím zadajte nastavenie.
1. Veľ.sken. (Scan size) Vyberte veľkosť originálu. 2. Formát (Format) Výber formátu naskenovaných údajov. 3. Rozl.sken (Scan res) (rozlíšenie skenovania) Výber rozlíšenia skenovania. 4. Ukážka (Preview) Zapnutie alebo vypnutie zobrazenia ukážky naskenovaných údajov pri ukladaní údajov na pamäťovú kartu. 5. Obmedz. presvit. (Reduce show-thru) (zamedzenie presvitaniu) Pri skenovaní tenkého dokumentu, napríklad novín, môžu presvitať znaky na zadnej strane.
Nastavenia skenovania v sieti Pripojením skenera alebo tlačiarne k sieti môžete tento produkt zdieľať s viacerými počítačmi alebo skenovať obrázky do vybratého počítača. Dôležité Viacerí používatelia nemôžu skenovať naraz. Poznámka Sieťové nastavenia skenera alebo tlačiarne vyberte vopred z Inštalačného disku alebo podľa pokynov na webovej stránke. Pri sieťovom pripojení trvá skenovanie dlhšie než pri pripojení USB. Ak chcete povoliť skenovanie prostredníctvom siete, vyberte nasledujúce nastavenia.
Na domovskej obrazovke kliknite na tlačidlo IJ Network Scanner Selector EX. Ak sa aplikácia IJ Network Scanner Selector EX na domovskej obrazovke nezobrazuje, vyberte kľúčové tlačidlo Vyhľadávanie (Search) a vyhľadajte výraz „IJ Network Scanner Selector EX“. Windows 7/Windows Vista/Windows XP: V ponuke Štart (Start) kliknite na položky Všetky programy (All Programs) > Canon Utilities > IJ Network Scanner Selector EX > IJ Network Scanner Selector EX.
Poznámka V prípade pripojenia USB vyberte v časti Názov produktu (Product Name) položku „Canon XXX series“ (kde „XXX“ je názov modelu). 3. Ak chcete použiť iný skener pripojený k sieti, kliknite na tlačidlo Nastavenia (Settings...). 4. Kliknite na kartu (Všeobecné nastavenia) a v časti Názov produktu (Product Name) kliknite na tlačidlo Vyberte (Select). Zobrazí sa obrazovka nastavení skenovania z počítača aplikácie IJ Network Scanner Selector EX.
Windows 7/Windows Vista/Windows XP: V ponuke Štart (Start) kliknite na položky Všetky programy (All Programs) > Canon Utilities > IJ Network Scanner Selector EX > IJ Network Scanner Selector EX. Ikona sa zobrazí v oblasti oznámení na pracovnej ploche a zobrazí sa obrazovka nastavení skenovania z počítača. V takom prípade prejdite na krok č. 3. 2. V oblasti oznámení na pracovnej ploche pravým tlačidlom kliknite na položku (IJ Network Scanner Selector EX) a vyberte možnosť Nastavenia... (Settings...).
Výber odpovede na príkazy z ovládacieho panela použitím aplikácie IJ Scan Utility Aplikácia IJ Scan Utility umožňuje určiť odpovede pri skenovaní pomocou ovládacieho panela. Poznámka V nasledujúcich opisoch sa ako príklady používajú obrazovky na určenie odpovedí pri automatickom skenovaní pomocou ovládacieho panela. 1. Spustite aplikáciu IJ Scan Utility. 2. Kliknite na tlačidlo Nastavenia (Settings...). Zobrazí sa dialógové okno nastavení. 3.
Poznámka Podrobnosti si prečítajte na nasledujúcich stránkach. Dialógové okno Nastavenia (Uložiť v počítači (automaticky)) Dialógové okno Nastavenia (Uložiť v počítači (fotografie)) Dialógové okno Nastavenia (Uložiť v počítači (dokument)) Dialógové okno Nastavenia (Pripojiť k e-mailu (fotografie)) Dialógové okno Nastavenia (Pripojiť k e-mailu (dokument)) 4. V časti Možnosti skenovania (Scan Options) nastavte korekcie obrázkov. 5.
6. V časti Nastavenia aplikácie (Application Settings) vyberte aplikáciu, ktorá sa má spustiť po skenovaní. 7. Kliknite na tlačidlo OK. Po spustení skenovania pomocou ovládacieho panela bude skener reagovať podľa vybratých nastavení.
Skenovanie pomocou režimu prístupového bodu Keď zariadenie prejde do režimu prístupového bodu, môžete z externých zariadení, napríklad počítača alebo smartfónu, skenovať bez použitia prístupového bodu. Dôležité • Skôr než zariadenie začnete používať v režime prístupového bodu, zadajte názov prístupového bodu zariadenia a nastavenie zabezpečenia. Pred použitím zariadenia pomocou režimu prístupového bodu 1. Skontrolujte, či je zariadenie zapnuté. 2.
Poznámka • Podrobné informácie o skenovaní z externého zariadenia, napríklad počítača alebo smartfónu, prostredníctvom bezdrôtovej siete LAN nájdete v príručke príslušného zariadenia alebo aplikácie. • Skenovať môžete aj pomocou aplikácie PIXMA Printing Solutions. 8. Po dokončení skenovania ťuknite na položku Skončiť (Exit). V zariadení sa ukončí režim prístupového bodu. 9. Keď sa zobrazí obrazovka s potvrdením, ťuknutím na tlačidlo OK ukončite režim prístupového bodu.