<< Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MP499 Mac OS 1
<< Previous Next >> Installing Your Multifunction to Your Network for the First Time PIXMA MP499 Mac OS Preparing to Connect My Multifunction to My Network Network Requirements Notes on Wireless Connection Installing the Drivers & Software Registering the Printer & Scanner 3 3 4 5 14 2
Preparing to Connect My Multifunction To My Network << Previous Next >> Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that configuration of the computer and access point or router is complete.
Preparing to Connect My Multifunction To My Network << Previous Next >> An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Notes on Network Connection The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer.
Installing the Drivers & Software << Previous Next >> Software Installation To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.) IMPORTANT • Log on as the administrator (or a member of the Administrators group).
Installing the Drivers & Software << Previous Next >> Software Installation Do not connect the wireless LAN setup cable yet. Software installation requires temporary use of the wireless LAN setup cable. Step One Step Two Turn on the computer, then insert the Setup CDROM into the CD-ROM drive. Double-click the Setup icon of the CD-ROM folder to proceed to the following screen.
Installing the Drivers & Software << Previous Step Three Step Four Enter your administrator name and password. Click OK. Click Easy Install. Click Install. Next >> The drivers, application software, and on-screen manuals are installed. Note: If you want to select particular items to install, click Custom Install. If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.
Installing the Drivers & Software << Previous Step Five Step Six Select Use the printer on network, then click Next. When the Printer Detection screen appears, click Next. Next >> IMPORTANT Follow any on-screen instructions to proceed with the software installation. If the Printer Connection screen appears instead of the screen above, the connection method is not correctly selected in 5. Follow on-screen instructions and proceed with the installation.
Installing the Drivers & Software << Previous Step Seven Step Eight Make sure the machine is turned on, then click OK. When the Set Up New Printer screen appears, click Next. Next >> Note: If the Detected Printers List screen appears, click Set Up New Printer.
Installing the Drivers & Software << Previous Next >> Step Nine When the Connect Cable screen appears, connect the machine to the computer with the wireless LAN setup cable. Follow the on-screen instructions and click Next.
Installing the Drivers & Software << Previous Next >> Step Ten 10-A If the Detected Access Points List screen appears: If the screen below does not appear, perform 10-B. 1. Select the target access point name/network name (SSID). 2. Enter the network key. Enter upper and lower case letters of the alphabet correctly. Letters are case sensitive. To use WEP key number 2, 3 or 4, click WEP Key Number, then specify the WEP key number. 3. Click Connect Go to Step Eleven.
Installing the Drivers & Software << Previous Next >> Step Ten 10-B If the Confirm Connection Access Point screen appears. Make sure that the target access point is displayed, then click Yes. If a screen asking for permission to access the keychain appears, click Allow or Allow Once. Note: If the target access point is not displayed in the Confirm Connection Access Point screen, click No, then perform 10-A.
Installing the Drivers & Software << Previous Step Eleven Step Twelve When the Disconnect Cable screen appears, remove the wireless LAN setup cable, then click Next. Click Complete or OK on the Setup Completion screen.
Registering the Printer & Scanner << Previous Next >> Registering the Printer & Scanner This section describes how to register the machine on a Macintosh computer. Note: The alphanumeric characters after Canon MP499 series is the machine's Bonjour service name or MAC address. If the machine has not been detected, make sure of the following. - The machine is turned on. - The firewall function of any security software is turned off. - The computer is connected to the access point.
Registering the Printer & Scanner << Previous Next >> Step One When the Register Printer and Scanner screen appears, click Register Printer. Proceed to the section that relates to your operating system for further installation instructions Mac OS X v. 10.5.x / 10.6.x: Go to Step 2-A Mac OS X v. 10.4.
Registering the Printer & Scanner << Previous Step Two Step Two 2-A Select Canon MP499 series canonijnetwork and click Add. 2-B 1. When the Printer List window appears, click Add. Next >> Note: When the You have no printers available. screen appears, click Add.
Registering the Printer & Scanner << Previous Step Two Step Two 2-B 2. Click More Printers in the Printer Browser window. 2-B 3. Select Canon IJ Network in the pop-up menu, select Canon MP499 series in the list of printers, then click Add.
Registering the Printer & Scanner << Previous Step Two Step Three 2-B 4. Make sure that Canon MP499 series is added to the list of printers. When the Register Printer and Scanner screen appears, click Register Scanner. Next >> Go to Step Three.
Registering the Printer & Scanner << Previous Step Four Step Five Select Canon MXxxx series on the Scan-from-PC Settings screen, then click OK.. *xxx refers to the model number. Click Next on the Register Printer and Scanner screen. Next >> Wireless setup is now complete.
Registering the Printer & Scanner << Previous Step Six Step Seven Click Next on the Print Head Alignment Recommended screen. Click Next on the Register Printer and Scanner screen.
Registering the Printer & Scanner << Previous Next >> Step Eight If the User Registration screen appears, read the information and click Next or Cancel. If the Extended Survey Program screen appears: If you can agree to Extended Survey Program, click Agree. If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.).
Registering the Printer & Scanner << Previous Step Nine Click Exit. Setup is complete *It is necessary to restart the computer before scanning using the Operation Panel on the machine for the first time.
