PIXMA MP600 / MP600R SERVICE MANUAL Canon Copyright 2006, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
PIXMA MP600 I.
PIXMA MP600 II. TABLE OF CONTENTS Part 1: MAINTENANCE 1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer 1-2. Customer Maintenance 1-3. Product Life 1-4. Special Tools 1-5. Serial Number Location 2. LIST OF ERROR DISPLAY / INDICATION 2-1. Operator Call Errors 2-2. Service Call Errors 2-3. Other Error Messages 2-4. Warnings 2-5. Troubleshooting by Symptom 3. REPAIR 3-1. Notes on Service Part Replacement 3-2.
Part 2: TECHNICAL REFERENCE 1. NEW TECHNOLOGIES 2. CLEANING MODE AND AMOUNT OF INK PURGED 3. PRINT MODE 4. FAQ (Problems Specific to the MP600 and Corrective Actions) Part 3: APPENDIX 1. BLOCK DIAGRAM 2. CONNECTOR LOCATION AND PIN LAYOUT 2-1. Logic Board 2-2. Carriage Board (Print Head Connector) 2-3. Print Beam / PictBridge Board 2-4. Card Slot Board (Card Slot Unit) 2-5. Operation Panel Board 3. PIXMA MP600 SPECIFICATIONS 4. PRINT MEDIA SPECIFICATIONS
PIXMA MP600 TABLE OF CONTENTS Part 1 MAINTENANCE
Part 1: MAINTENANCE TABLE OF CONTENTS 1. MAINTENANCE 1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer (1) Adjustment Adjustment Timing Destination settings (EEPROM settings) - At logic board replacement EEPROM initialization - At logic board replacement Ink absorber counter resetting - At logic board replacement Purpose To set destination. To initialize settings To reset the ink absorber counter.
Document pressure sheet position adjustment - At document pressure sheet replacement To adjust the pressure sheet to fit in place to None. the four corners of the platen glass when the cover is closed. 1 min. Caution: DO NOT loosen the red screws at both ends of the carriage shaft, securing the print head position, as they are not readjustable. The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit..
1-3. Product Life (1) Machine Specified print volume (I) or the years of use (II), whichever comes first. (I) Print volume: 24,000 pages Black 1500 character pattern 11,000 pages Color 7.
Part 1: MAINTENANCE TABLE OF CONTENTS 2. LIST OF ERROR DISPLAY / INDICATION Errors and warnings are displayed by the following ways: 1) Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD in text and by icon. 2) Messages during printing from a computer are displayed on the MP driver Status Monitor. 3) Error codes are printed in the "operator call/service call error record" area in EEPROM information print.
- Faulty EEPROM data of the print head. [1405] incorrect. Install the correct print head. - Print head hardware error. [1682] Inner cover open. [1841] --- Inner cover open during printing on paper. [1846] --- Inner cover is open. Close the inner cover and press [OK]. Multiple ink tanks of the same color installed. [1681] U071 (Applicable ink tank icon) Ink tank in a wrong position. [1680] U072 Some ink tanks are not installed in place. Close the inner cover, and press the OK button.
button, the automatic print head alignment will not be re-done. The remaining ink amount unknown. [1683] U130 (Applicable ink tank icon) An ink tank which has once been empty is installed. Replace the applicable ink tank with a new one. The remaining level of the following ink cannot Printing with a once-empty ink tank can be correctly detected. damage the printer. Replace the ink tank. To continue printing without replacing the ink tank(s), press the Stop/Reset button for 5 sec.
Part 1: MAINTENANCE TABLE OF CONTENTS 2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (COPY button), or Alarm LED Lit in Orange) Service call errors are indicated by the number of cycles the Alarm LED and COPY button blink, and the corresponding error code is displayed on the LCD.
15 times USB Host VBUS overcurrent [9000] The USB Host VBUS is overloaded. - Logic board ass'y (QM3-0250)*1 16 times Pump roller sensor error [5C20] The pump roller position cannot be detected. - Logic board ass'y (QM3-0250) *1 - Purge unit (QM3-0033) 17 times Paper eject encoder error [6010] An error occurred in the paper eject encoder signal. - Logic board ass'y (QM3-0250) *1 - Platen unit (QM3-1794) 19 times Ink tank position sensor error [6502] None of the ink tank position is detected.
Part 1: MAINTENANCE TABLE OF CONTENTS 2-3. Other Error Messages Message on the LCD The selected paper cannot be fed from cassette. Change the paper source and press [OK]. Cause The paper type being used (business card, Credit Card size paper, or stickers, etc.) is not supported for paper feeding from the cassette. Solution Change the paper source to the ASF. Device memory is full. Reduce the The memory is not sufficient to do the print amount of photos, films, copies to scan. job.
Part 1: MAINTENANCE TABLE OF CONTENTS 2-4. Warnings Warning Low ink Message on the LCD Solution The following ink is low. Continue? - Select Yes, and press the OK button. (Icon of each ink tank) Yes => Printing starts, and it is indicated on the LCD. No - Select No, and press the OK button. In Camera Direct Printing, only "Yes" can be selected. Print head temperature rise => Printing is cancelled, and the LCD returns to the display immediately before printing was attempted.
Part 1: MAINTENANCE TABLE OF CONTENTS 2-5. Troubleshooting by Symptom Symptom Faulty operation Solution The power does not turn on. - Confirm the connection of The power turns off immediately after power-on. - the power cord, and - between the logic board and the power supply unit. - Replace the - AC adapter, or - logic board*1. A strange noise occurs. - Remove foreign material. - Attach a removed part if any.
- logic board*1. - Remove foreign material from the purge unit caps, if any. - Replace the purge unit. Printing is faint, or white lines appear on printouts even after print head cleaning. Line(s) not included in the print data appears on printouts. - Remove and re-install the print head. - Replace the - ink tank, - print head*2, - purge unit, or - logic board*1. Paper gets smeared. - Feed several sheets of paper. - Perform bottom plate cleaning. - Clean the paper path with cotton swab or cloth.
*1: Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information print). If the counter value is 7% or more, also replace the ink absorber kit (QY5-0181) when replacing the logic board ass'y. [See 3-3. Adjustment / Settings, (5) Service mode, for details.] *2: Replace the print head only after the print head deep cleaning is performed 2 times, and when the problem persists. <1-2-5.
Part 1: MAINTENANCE TABLE OF CONTENTS 3. REPAIR 3-1. Notes on Service Part Replacement (and Disassembling / Reassembling) Notes on replacement*1 Adjustment / settings - Before removal of the logic board ass'y, remove the power cord, and allow for approx. 1 minute (for discharge of capacitor's accumulated charges), to prevent damages to the logic board ass'y. - Before replacement, check the ink absorber counter value (by service test print or EEPROM information print).
Timing slit disk eject film QC2-0476 Timing slit disk film QC2-0475 - Confirm no grease is on the film. (Wipe off any grease thoroughly with ethanol.) alignment in the user mode. - Do not bend the film Print head QY6-0061 After replacement: 1. Perform the print head alignment in the user mode. - Service test print *1: General notes: - Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly. [See 3-2.
Part 1: MAINTENANCE TABLE OF CONTENTS 3-2. Special Notes on Repair Servicing (1) External cover and scanner unit removal (i) Front cover L removal Insert a flat-blade screwdriver in the location indicated by the red circle, and release the front cover L while pushing it upward using the screwdriver. (ii) Front cover R removal Insert the flat-blade screwdriver in the location indicated by the red circle, and release the front cover R in the same way as step (i).
(iv) Remove 2 screws from the front of the machine (1 each on the right and left sides). (v) Remove the side covers L and R. (vi) Scanner lock arm unit removal Push the main case tab outward to unlock the unit. When assembling the scanner lock arm unit, make sure that the unit is in the correct orientation.
(vii) Main case removal Remove screws from the right and left sides of the paper ejection side. Remove screws from the right and left sides of the sheet feeder side.
(2) Operation panel and LCD viewer unit removal (i) Separate the scanner unit from the document cover unit. (ii) Remove screws from the bottom of the document cover unit. (iii) Remove screws, and disconnect the flexible cable and harness. Harness and core bundled: (iv) Remove 2 screws from the LCD hinge.
(3) Document pressure sheet replacement Be cautious of the following when replacing the document pressure sheet: (i) Position one of the corners of the document pressure sheet to the reference mark (indicated by the red arrow below) on the platen glass. (ii) Slowly close the document cover unit so that the document pressure sheet will fix to the cover unit with the double-sided adhesive tape in 4 corners.
(4) Printer unit separation from the bottom case unit (i) Unlocking the carriage unit To remove the screw beneath the carriage unit in the home position, unlock the carriage unit first as follows: Rotate the gear (indicated by the red square) toward the rear side of the machine 2 or 3 times. The carriage will be unlocked. (ii) Slide the carriage to the opposite of the home position, and remove the screw.
(5) Flexible cable and harness wiring, connection Be cautious of wiring of the flexible cables and harness. Improper wiring or connection may cause breakage of a line, leading to ignition or emission of smoke. (i) Logic board ass'y wiring (ii) Paper feed motor side wiring <1-3-2.
Part 1: MAINTENANCE TABLE OF CONTENTS 3-3. Adjustment / Settings (1) Paper feed motor adjustment 1) When attaching the motor, fasten the screws so that the belt is properly stretched (in the direction indicated by the blue arrow in the figure below). 2) After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print operation (due to dislocation of the belt or gear, or out-of-phase motor, etc.) occurs.
1-24
■ Other 1 drop = 9 to 18 mg No Part name Where to apply grease / oil Drawing No. Grease / oil Grease / oil Number of amount drops x (mg) locations 1 Jog wheel base Easy-Scroll Wheel sliding portion (1) Floil KG107A 9 to 18 2 Jog wheel Ring key joint (2) Floil KG107A 3 1x4 (3) Ink absorber counter setting When the logic board ass'y is replaced, reset the ink absorber counter. In addition, according to the ink absorber counter value, replace the ink absorber (ink absorber kit).
Turn on the machine. On the operation panel, press the HOME button, select Settings, and Maintenance or Device settings, then a desired function. Menu Remarks Cleaning Nozzle check pattern Deep cleaning Roller cleaning Auto head align (automatic print head alignment) Manual head align (manual print head alignment) Bottom plate cleaning Fold a sheet of A4 or Letter size plain paper in half, then open it. Set the paper in the ASF with the opened surface facing up.
Part 1: MAINTENANCE TABLE OF CONTENTS (5) Service mode A: Service test print, EEPROM initialization, Ink absorber counter resetting Function Service test print - Model name Procedures Remarks See "Service mode operation procedures" below. Set a sheet of A4 or letter size paper. See "Service mode operation procedures" below. The following items are NOT initialized, and the shipment arrival flag is not on: - ROM version For print sample, see 3-4.
1) With the machine power turned off, while pressing the Stop/Reset button, press and hold the ON/OFF button. (DO NOT release the buttons). The Power LED lights in green to indicate that a function is selectable. 2) While holding the ON/OFF button, release the Stop/Reset button. (DO NOT release the ON/OFF button.) 3) While holding the ON/OFF button, press the Stop/Reset button 2 times, and then release both the ON/OFF and Stop/Reset buttons.
B: Destination settings Time(s) LED indication Destination CD / DVD print 0 times Green (Power) No change of the destination 1 time Orange (Alarm) Japan Supported 2 times Green (Power) Korea Not supported 3 times Orange (Alarm) US, CND, LAM Not supported 4 times Green (Power) Europe Supported 5 times Orange (Alarm) Australia Supported 6 times Green (Power) Asia Supported 7 times Orange (Alarm) China Supported 8 times Green (Power) Taiwan Supported 9 times or more Oran
3) In the printout, select the Pattern No. in which streaks or lines are the least noticeable, press the Stop/Reset button the same number of time (s) as the selected Pattern No., then press the ON/OFF button.
3-1) LF correction value Selected pattern number Number of times the Stop/Reset button is pressed (M) 1 1 time 0 0 times 2 2 times Note: - Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green. - If the Stop/Reset button is pressed 3 times or more, then the ON/OFF button is pressed, the machine returns to the service mode menu selection.
<1-3-3, (5) Service mode_A~C> 1-32
Part 1: MAINTENANCE TABLE OF CONTENTS D: Left margin correction Adjust the left margin for duplex printing or printing from the cassette. 1) Duplex printing from the ASF and cassette In the left margin correction mode, press the Stop/Reset button 1 time, then press the ON/OFF button 1 time. Duplex printing is performed from the ASF and cassette.
3) Setting of the left margin correction value ("+" means to increase the left margin) Press the Stop/Reset button the specified number of time(s) according to the correction value listed in the table below, then press the ON/OFF button.
1-35
1-36
E: Ink absorber counter setting Set the ink absorber counter value to a replaced new EEPROM after the logic board is replaced in servicing. 1) Before replacement of the logic board ass'y, check the ink absorber counter value in EEPROM information print. See 3-4. Verification Items, (2) EEPROM information print.
F: Button and LCD test Confirm the operation after replacement of the operation panel unit, board, or LCD unit. 1) In the button and LCD test mode, press the Stop/Reset button. The LCD turns blue, waiting for a button to be pressed. 2) Press each button of the operation panel (total 17 buttons). 3) Only one button should be pressed at one time. If 2 or more buttons are pressed at the same time, only one of them is considered to be pressed, and the other buttons are ignored.
4-4) When the Easy-Scroll Wheel is rotated counterclockwise 1 round (24 steps), press the OK button. The color of all segments turns red. 5) Open the scanning unit (printer cover) to display the color pattern. If there is any step left un-selected (a blue segment remained in step 4) above), even the Stop/Reset button is not accepted. 6) Adjust the transparent color and LCD flicker, as follows: 6-1) Press the OK button. "OK1" in white is displayed on the black background.
<1-3-3, (5) Service mode_D~F> 1-40
Part 1: MAINTENANCE TABLE OF CONTENTS 3-4. Verification Items (1) Service test print On the service test print (sample below), confirm the EEPROM information as shown below. - Top area: MP600: Model name Vx.xx: ROM version D = xxx.x: Ink absorber counter value (%) USB (xxxxxx): USB serial number - Middle area: JPN: Destination - Bottom area: FA=xx xx xx: Reserved for plant use VrefPWM=xxxxx: TFT LCD flicker adjustment value Temp.=yyy: Internal temperature AB(K=OK Y=....
<1-3-4, (1) Service test print> 1-42
Part 1: MAINTENANCE TABLE OF CONTENTS 3-4. Verification Items (2) EEPROM information print Print sample: MP600 JPN V1.00 ST=2006/06/15-18:30 LPT=2006/07/09-09:09 ER(ER0=1000 ER1=5100) P_ON(S=00009) MSD(002) IF(USB1=1) PC(M=002 R=000 T=001 D=009 C=000) D=004.
SC=00034 SCAN_ER(ER0=0000 ER1=0000) SC-dpi(75=00000 150=00000 300=00029 600=00005 1200=00000 2400=00000 4800=00000) SG(GY=00003 CL=00002) MCASF(PP=00000 SP+PR+GP=00000 OTH=00000) MCUT(PP=00000 SP+PR+GP =00000 OTH=00000) CCASF(PP=00000 HR+MP=00000 PR+SP+SG=00000 GP=00000 PC=00000) CCUT(PP=00000 HR+MP=00000 PR+SP+SG =00000 GP=00000 PC=00000) Printed items: 1. Model name 2. Destination 3. ROM version 4. Installation date 5. Last printing time 6. Operator call/service call error record 7.
38. Language 39. Memory card use count (CDI = Card Install) 40. Total Card Direct print pages (CDP = Card Print) 41. Card Direct print pages: Photo Paper Pro (CDD-PR = Card Direct PR) (4 x 6, 5 x 7, postcard, A4/Letter) 42. Card Direct print pages: Photo Paper Plus Glossy (CDD-SP = Card Direct SP/PP) (4 x 6, 5 x 7, postcard, A4/Letter) 43. Card Direct print pages: Matte Photo Paper (CDD-MP = Card Direct MP) (4 x 6, 5 x 7, postcard, A4/Letter) 44.
Part 1: MAINTENANCE TABLE OF CONTENTS 4. MACHINE TRANSPORTATION This section describes the procedures for transporting the machine for returning after repair, etc. 1) In the service mode, press the ON/OFF button to finish the mode, and confirm that the paper lifting plate of the sheet feed unit is raised. 2) Keep the print head and ink tanks installed in the carriage. See Caution 1 below. 3) Turn off the machine to securely lock the carriage in the home position.
PIXMA MP600 TABLE OF CONTENTS Part 2 TECHNICAL REFERENCE
Part 2: TECHNICAL REFERENCE TABLE OF CONTENTS 1. NEW TECHNOLOGIES 1) Easy-Scroll Wheel With the Easy-Scroll Wheel, a menu can be easily selected by rotating the wheel clockwise or counterclockwise. Together with the operation panel which is located at the front center, usability has been significantly enhanced. 2) Print speed By adopting longer nozzles and the double encoder system, higher photo print speed has been achieved. - 4 x 6 photo (PP-101, standard, borderless)*1: Approx. 28 sec.
Unknown: Raw ink remains, but the dot count value exceeds the threshold of complete exhaustion of ink. By pressing and holding the Stop/Reset button for 5 seconds or longer, the function to detect the remaining ink amount can be disabled.
Part 2: TECHNICAL REFERENCE TABLE OF CONTENTS 2. CLEANING MODE AND AMOUNT OF INK PURGED To prevent printing problems due to bubbles, dust, or ink clogging, print head cleaning is performed before the start of printing (when the cleaning flag is on), except in the following cases: - Cleaning on arrival: 1st: Performed when the scanning unit (printer cover) is closed after the print head and ink tanks are installed. 2nd: Performed before automatic print head alignment.
*1: The counter for the on-arrival cleaning is checked at opening and closing of the scanning unit (the first opening and closing only), before start of printing, at dot-count cleaning (at paper ejection), and at manual cleaning, and the on-arrival cleaning is performed according to the counter value. After each on-arrival cleaning, the counter value is reduced by 1. When the counter value is 3, 2, or 1: On-arrival cleaning is performed. When the counter value is 0: On-arrival cleaning is not performed.
Part 2: TECHNICAL REFERENCE TABLE OF CONTENTS 3. PRINT MODE Default setting Selectable in the MP driver Main tab (including settings via the operation panel or a connected camera in Direct printing) Custom setting Ink used Print control PigBK: PGI-5BK C: CLI-8C M: CLI-8M Y: CLI-8Y k: CLI-8BK c: CLI-8C (small droplet) m: CLI-8M (small droplet) Bi: Bi-directional Uni: Uni-directional 3-1.
Print control Ink used Other photo paper 5 passes, Bi C/M/Y/c/m/k 7 passes, Bi C/M/Y/c/m/k Print quality Resolution HxV(dpi) Print control Ink used 8 passes, Bi C/M/Y/c/m/k Standard C/M/Y/c/m/k:1200x1200 8 passes, Bi C/M/Y/c/m/k 3-2.
3-4.
3-6.
Part 2: TECHNICAL REFERENCE TABLE OF CONTENTS 4. FAQ (Problems Specific to the MP600 and Corrective Actions) No. * Function Phenomenon Paper feeding problems - Jam - Skewed paper feeding 1 C Paper feeding Skewed paper feeding (at the level of +/- 1%) 2 C Print results Condition Cause Corrective action Possible call or complaint - Low temperature and low humidity environment Due to curl of a - Eliminate the curl of - Paper jams.
in automatic duplex printing (lines or streaks perpendicular to the paper feed direction) printing (Photo Paper the sheet feed unit Plus Double Sided, used for duplex postcards, plain paper) printing, ink mist may accumulate, smearing paper. operational solution: smeared. Cancel automatic duplex printing, and manually print each side of paper. Cleaning by user: 1. Perform Bottom plate cleaning (from the MP driver) up to 3 times*1. 4 2.
Since the sub-rollers usually do not contact the paper, ink mist can easily accumulate, especially during printing on smallsized paper which never contacts the sub-rollers. Skewed paper feeding 7 B Print results - SG-101 When 10 sheets of - Straighten the paper. - Paper feeds at an angle. - Paper feeding from the paper are set in the - Set 5 or less sheets ASF, and if they curl ASF of paper in the ASF. - A margin significantly, the appears on - 10 sheets (max.) set in curled portions of printouts.
2) Fold the paper at approx. 60 mm from the end, and fold the folded end in half backward, as shown below. 3) Moisten the folded end portion (indicated by the blue circle in the figure below) using a wipe, and set the paper in the ASF so that the moistened edge of the paper contacts the 2 sub-rollers. Then, fold the other end of the paper along the ASF cover edge to hook the paper to the ASF cover, as shown below. 4) On the machine, select Settings, Maintenance, then Roller cleaning.
PIXMA MP600 TABLE OF CONTENTS Part 3 APPENDIX
Part 3: APPENDIX TABLE OF CONTENTS 3. PIXMA MP600 SPECIFICATIONS Type Desktop serial color inkjet printer Paper feeding method Auto sheet feed (ASF, cassette, automatic duplex printing, CD / DVD printing*1) Resolution 9,600 x 2,400dpi (Max.) 4 x 6 photo (PP-101, standard, borderless)*: Approx. 28 sec. Custom 5 Standard Black text (plain paper, FINE pattern) 30ppm 14.8ppm Color (plain paper, FINE pattern) 24ppm 11.
Environmental requirements Power supply Non operation Humidity 10%RH to 90%RH (no condensation) Temperature 0C to 40C (32F to 104F) Humidity 5%RH to 95%RH (no condensation) Power supply voltage, frequency Power consumption Standby Power-off AC 100 to 240V, 50/60Hz Approx. 17W (max.) Approx. 1.5W Approx. 0.8W External dimensions - With the trays retracted: Approx. 450 (W) x 389 (D) x 194 (H)mm - With the trays extended: Approx. 450 (W) x 593 (D) x 337 (H)mm Weight Approx. 10.
- Notations for the Americas should be confirmed with the related marketing section of each sales company in the Americas. A4 / Letter (max.) Document size Preset ratio: max. (400%), 4x6 -> LTR (183%) 5x7 -> LTR (156%) A5 -> A4 (141%) B5 -> A4 (115%) A4 -> LTR (94%) Enlargement / reduction A4 -> B5 (86%) A4 -> A5 (70%) min. (25%) Zoom: 25 to 400% (in increments of 1%) Number of continuous copies Monochrome / color: 1 to 99 copies - Compact Flash TYPE I/II (3.
1 photo per page (bordered/borderless, only with borders for plain paper) Index printing: A4/Letter: 80 photos per page 4" x 6": 15 photos per page 5" x 7": 35 photos per page Credit Card size: 6 photos per page 8" x 10": 72 photos per page Print layout Wide size: 28 photos per page Layout printing: 2, 4, 8 photos per page (bordered/borderless) Half (bordered/borderless, with/without lines) Card Direct printing Album (4 photos per page, right/left) Mix 1/2/3 (for A4/LTR) Sticker printing: 16 stickers Inf
Printing via Bluetooth communication (optional) Communication range devices, or radio wave conditions) Used frequency band 2.4GHz Communication speed Approx. 720kbps Supported profile BIP, OPP, SPP, HCRP - Windows XP Service Pack 2 or later - Windows XP Service Pack 1 or later: Supported OS for HCRP Microsoft "Support for Bluetooth Wireless Devices" or Toshiba Bluetooth Stack for Windows Ver. 3.00.10 or later has to be installed - Mac OS X v 10.3.3 or later External dimensions 18.5 (W) x 47.
Part 3: APPENDIX TABLE OF CONTENTS 4. PRINT MEDIA SPECIFICATIONS The following types of paper are recommended: Type Name Size Paper feeding method (auto) ASF stacking capacity (max.) Plain paper 64 to 105 g/m2 A4, LTR, A5, LGL*1 , custom ASF, Cassette 13 mm Super White Paper SW-101/201 A4, LTR ASF, Cassette 13 mm High Resolution Paper HR-101 A4, LTR ASF, Cassette Approx. 80 sheets Glossy Photo Paper GP-401 A4, LTR ASF, Cassette GP-401 4x6 101.